RTM_NEWADDR notification is sent when IFA_F_TENTATIVE is cleared from
the address. So if the address is added and deleted before DAD probes
completes, the RTM_DELADDR will be sent for which there was no
RTM_NEWADDR causing asymmetry in notification. However if the same
logic is used while sending RTM_DELADDR notification, this asymmetry
can be avoided.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
CC: Patrick McHardy <kaber@trash.net>
CC: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The VF driver is using the wrong struct when sending commands to the NIC
firmware, sometimes causing adverse effects in the firmware.  The right
struct is the one that the PF is using, so make the VF use that as well.
Signed-off-by: Prasad Kanneganti <prasad.kanneganti@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tools: psock_tpacket: block Rx until socket filter has been added and socket has been bound to loopback.

Packets from any/all interfaces may be queued up on the PF_PACKET socket
before it is bound to the loopback interface by psock_tpacket, and
when these are passed up by the kernel, they could interfere
with the Rx tests.

Avoid interference from spurious packet by blocking Rx until the
socket filter has been set up, and the packet has been bound to the
desired (lo) interface. The effective sequence is
	socket(PF_PACKET, SOCK_RAW, 0);
	set up ring
	Invoke SO_ATTACH_FILTER
	bind to sll_protocol set to ETH_P_ALL, sll_ifindex for lo
After this sequence, the only packets that will be passed up are
those received on loopback that pass the attached filter.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For TCP sockets, TX timestamps are only captured when the user data
is successfully and fully written to the socket. In many cases,
however, TCP writes can be partial for which no timestamp is
collected.

Collect timestamps whenever any user data is (fully or partially)
copied into the socket. Pass tcp_write_queue_tail to tcp_tx_timestamp
instead of the local skb pointer since it can be set to NULL on
the error path.

Note that tcp_write_queue_tail can be NULL, even if bytes have been
copied to the socket. This is because acknowledgements are being
processed in tcp_sendmsg(), and by the time tcp_tx_timestamp is
called tcp_write_queue_tail can be NULL. For such cases, this patch
does not collect any timestamps (i.e., it is best-effort).

This patch is written with suggestions from Willem de Bruijn and
Eric Dumazet.

Change-log V1 -> V2:
	- Use sockc.tsflags instead of sk->sk_tsflags.
	- Use the same code path for normal writes and errors.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'rxrpc-rewrite-20170105' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs

David Howells says:

====================
rxrpc: Update tracing and proc interfaces

This set of patches fixes and extends tracing:

 (1) Fix the handling of enum-to-string translations so that external
     tracing tools can make use of it by using TRACE_DEFINE_ENUM.

 (2) Extend a couple of tracepoints to export some extra available
     information and add three new tracepoints to allow monitoring of
     received DATA packets, call disconnection and improper/implicit call
     termination.

and adds a bit more procfs-exported information:

 (3) Show a call's hard-ACK cursors in /proc/net/rxrpc_calls.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Since there can be multiple dsa switches stacked together but
not all of devicetree nodes available at the time of calling
dsa_dst_parse(), EPROBE_DEFER can be returned by it. When this
happens, only the last dsa switch has to be deleted by
dsa_dst_del_ds(), but not the whole list, because next time linux
cames back to this function it will try to add only the last dsa
switch which returned EPROBE_DEFER.
Signed-off-by: Volodymyr Bendiuga <volodymyr.bendiuga@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This chip needs MV88E6XXX_FLAG_G2_INT
Signed-off-by: Volodymyr Bendiuga <volodymyr.bendiuga@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

xemaclite_remove_ndev() is a simple wrapper around free_netdev()
checking for NULL before the call. All possible paths calling
it are guaranteed to pass a non-NULL argument, so rather call
free_netdev() directly.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The io_region_size and dma_alloc members of struct ethoc are only
written but never read, so they might as well be removed.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Show a call's hard-ACK cursors in /proc/net/rxrpc_calls so that a call's
progress can be more easily monitored.
Signed-off-by: David Howells <dhowells@redhat.com>

Add the following extra tracing information:

 (1) Modify the rxrpc_transmit tracepoint to record the Tx window size as
     this is varied by the slow-start algorithm.

 (2) Modify the rxrpc_rx_ack tracepoint to record more information from
     received ACK packets.

 (3) Add an rxrpc_rx_data tracepoint to record the information in DATA
     packets.

 (4) Add an rxrpc_disconnect_call tracepoint to record call disconnection,
     including the reason the call was disconnected.

 (5) Add an rxrpc_improper_term tracepoint to record implicit termination
     of a call by a client either by starting a new call on a particular
     connection channel without first transmitting the final ACK for the
     previous call.
Signed-off-by: David Howells <dhowells@redhat.com>

Fix the way enum values are translated into strings in AF_RXRPC
tracepoints.  The problem with just doing a lookup in a normal flat array
of strings or chars is that external tracing infrastructure can't find it.
Rather, TRACE_DEFINE_ENUM must be used.

Also sort the enums and string tables to make it easier to keep them in
order so that a future patch to __print_symbolic() can be optimised to try
a direct lookup into the table first before iterating over it.

A couple of _proto() macro calls are removed because they refered to tables
that got moved to the tracing infrastructure.  The relevant data can be
found by way of tracing.
Signed-off-by: David Howells <dhowells@redhat.com>

When TX timestamping is in use with TPACKET_V3's TX ring, then we'll
hit the BUG() in __packet_set_timestamp() when ring buffer slot is
returned to user space via tpacket_destruct_skb(). This is due to v3
being assumed as unreachable here, but since 7f953ab2 ("af_packet:
TX_RING support for TPACKET_V3") it's not anymore. Fix it by filling
the timestamp back into the ring slot.

Fixes: 7f953ab2 ("af_packet: TX_RING support for TPACKET_V3")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull xfs fixes from Darrick Wong:

 - fixes for crashes and double-cleanup errors

 - XFS maintainership handover

 - fix to prevent absurdly large block reservations

 - fix broken sysfs getter/setters

* tag 'xfs-for-linus-4.10-rc3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: fix max_retries _show and _store functions
  xfs: update MAINTAINERS
  xfs: fix crash and data corruption due to removal of busy COW extents
  xfs: use the actual AG length when reserving blocks
  xfs: fix double-cleanup when CUI recovery fails

Pull networking fixes from David Miller:

 1) stmmac_drv_probe() can race with stmmac_open() because we register
    the netdevice too early. Fix from Florian Fainelli.

 2) UFO handling in __ip6_append_data() and ip6_finish_output() use
    different tests for deciding whether a frame will be fragmented or
    not, put them in sync. Fix from Zheng Li.

 3) The rtnetlink getstats handlers need to validate that the netlink
    request is large enough, fix from Mathias Krause.

 4) Use after free in mlx4 driver, from Jack Morgenstein.

 5) Fix setting of garbage UID value in sockets during setattr() calls,
    from Eric Biggers.

 6) Packet drop_monitor doesn't format the netlink messages properly
    such that nlmsg_next fails to work, fix from Reiter Wolfgang.

 7) Fix handling of wildcard addresses in l2tp lookups, from Guillaume
    Nault.

 8) __skb_flow_dissect() can crash on pptp packets, from Ian Kumlien.

 9) IGMP code doesn't reset group query timers properly, from Michal
    Tesar.

10) Fix overzealous MAIN/LOCAL route table combining in ipv4, from
    Alexander Duyck.

11) vxlan offload check needs to be more strict in be2net driver, from
    Sabrina Dubroca.

12) Moving l3mdev to packet hooks lost RX stat counters unintentionally,
    fix from David Ahern.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
  sh_eth: enable RX descriptor word 0 shift on SH7734
  sfc: don't report RX hash keys to ethtool when RSS wasn't enabled
  dpaa_eth: Initialize CGR structure before init
  dpaa_eth: cleanup after init_phy() failure
  net: systemport: Pad packet before inserting TSB
  net: systemport: Utilize skb_put_padto()
  LiquidIO VF: s/select/imply/ for PTP_1588_CLOCK
  libcxgb: fix error check for ip6_route_output()
  net: usb: asix_devices: add .reset_resume for USB PM
  net: vrf: Add missing Rx counters
  drop_monitor: consider inserted data in genlmsg_end
  benet: stricter vxlan offloading check in be_features_check
  ipv4: Do not allow MAIN to be alias for new LOCAL w/ custom rules
  net: macb: Updated resource allocation function calls to new version of API.
  net: stmmac: dwmac-oxnas: use generic pm implementation
  net: stmmac: dwmac-oxnas: fix fixed-link-phydev leaks
  net: stmmac: dwmac-oxnas: fix of-node leak
  Documentation/networking: fix typo in mpls-sysctl
  igmp: Make igmp group member RFC 3376 compliant
  flow_dissector: Update pptp handling to avoid null pointer deref.
  ...

Lookup in the ATU can be performed starting from a given MAC
address. This is faster than starting with the first possible MAC
address and iterating all entries.

Entries are returned in numeric order. So if the MAC address returned
is bigger than what we are searching for, we know it is not in the
ATU.

Using the benchmark provided by Volodymyr Bendiuga
<volodymyr.bendiuga@gmail.com>,

https://www.spinics.net/lists/netdev/msg411550.html

on an Marvell Armada 370 RD, the test to add a number of static fdb
entries went from 1.616531 seconds to 0.312052 seconds.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The RX descriptor word 0 on SH7734 has the RFS[9:0] field in bits 16-25
(bits  0-15 usually used for that are occupied by the packet checksum).
Thus  we need to set the 'shift_rd0'  field in the SH7734 SoC data...

Fixes: f0e81fec ("net: sh_eth: Add support SH7734")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we failed to set up RSS on EF10 (e.g. because firmware declared
 RX_RSS_LIMITED), ethtool --show-nfc $dev rx-flow-hash ... should report
 no fields, rather than confusingly reporting what fields we _would_ be
 hashing on if RSS was working.

Fixes: dcb4123c ("sfc: disable RSS when unsupported")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

t6fw-1.15.15.0 enabled compressed error vector in cpl_rx_pkt for T6.
Updating driver to take care of these changes.
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Arjun V <arjun@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sergei Shtylyov says:

====================
sh_eth: E-MAC interrupt handler cleanups

   Here's a set of 3 patches against DaveM's 'net-next.git' repo. I'm cleaning
up the E-MAC interrupt handling with the main goal of factoring out the E-MAC
interrupt handler into a separate function.

[1/3] sh_eth: handle only enabled E-MAC interrupts
[2/3] sh_eth: no need for *else* after *goto*
[3/3] sh_eth: factor out sh_eth_emac_interrupt()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The E-MAC interrupt (EESR.ECI) is not always caused  by an error condition,
so  it really shouldn't be handled by sh_eth_error(). Factor out the E-MAC
interrupt handler, sh_eth_emac_interrupt(),  removing the ECI bit from the
EESR's values throughout the driver...

Update Cogent Embedded's copyright and clean up the whitespace in Renesas'
copyright, while at it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Well, checkpatch.pl complains about *else* after *return* and *break* but
not after *goto*... and it probably should have complained about the code
in sh_eth_error().  Win couple LoCs by removing that *else*. :-)
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver should only handle the enabled E-MAC interrupts, like it does
for the E-DMAC interrupts since commit 3893b273 ("sh_eth: workaround
for spurious ECI interrupt"),  so mask ECSR with  ECSIPR when reading it
in sh_eth_error().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Madalin Bucur says:

====================
dpaa_eth: a couple of fixes

Add cleanup on PHY initialization failure path, avoid using
uninitialized memory at CGR init.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The QBMan CGR options needs to be zeroed before calling the init
function
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: systemport: Fix padding vs. TSB insertion

This patch series fixes how we pad the packets submitted to the SYSTEMPORT
adapter, and how the transmit status block (prepended 8 bytes) fits in the
picture. The first patch is not technically a bug fix, but is required for the
second path to be applied and to greatly simplify the skb length calculation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Inserting the TSB means adding an extra 8 bytes in front the of packet
that is going to be used as metadata information by the TDMA engine, but
stripped off, so it does not really help with the packet padding.

For some odd packet sizes that fall below the 60 bytes payload (e.g: ARP)
we can end-up padding them after the TSB insertion, thus making them 64
bytes, but with the TDMA stripping off the first 8 bytes, they could
still be smaller than 64 bytes which is required to ingress the switch.

Fix this by swapping the padding and TSB insertion, guaranteeing that
the packets have the right sizes.

Fixes: 80105bef ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since we need to pad our packets, utilize skb_put_padto() which
increases skb->len by how much we need to pad, allowing us to eliminate
the test on skb->len right below.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPvlan setup uses one mac-address (of master). The IPv6 link-local
addresses are derived using the mac-address on the link. Lack of
dev-ids makes these link-local addresses same for all slaves including
that of master device. dev-ids are necessary to add differentiation
when L2 address is shared.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The "out" label in dsa_switch_setup_one() is useless, thus remove it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

liquidio driver incorrectly indicates that PTP is supported in 23XX
adapters; this patch fixes that.  PTP is supported in 66XX and 68XX
adapters, and the driver correctly indicates that.
Signed-off-by: Prasad Kanneganti <prasad.kanneganti@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix a minor fallout from the merge of the timers and the networking
trees. The following error may result if the PTP_1588_CLOCK
prerequisites are not available:

drivers/built-in.o: In function `ptp_clock_unregister':
(.text+0x40e0a5): undefined reference to `pps_unregister_source'
drivers/built-in.o: In function `ptp_clock_unregister':
(.text+0x40e0cc): undefined reference to `posix_clock_unregister'
drivers/built-in.o: In function `ptp_clock_event':
(.text+0x40e249): undefined reference to `pps_event'
drivers/built-in.o: In function `ptp_clock_register':
(.text+0x40e5e1): undefined reference to `pps_register_source'
drivers/built-in.o: In function `ptp_clock_register':
(.text+0x40e62c): undefined reference to `posix_clock_register'
drivers/built-in.o: In function `ptp_clock_register':
(.text+0x40e68d): undefined reference to `pps_unregister_source'
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip6_route_output() never returns NULL so
check dst->error instead of !dst.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It must always be the case that CMSG_ALIGN(sizeof(hdr)) == sizeof(hdr).

Otherwise there are missing adjustments in the various calculations
that parse and build these things.
Signed-off-by: David S. Miller <davem@davemloft.net>

sizeof(struct cmsghdr) and sizeof(struct compat_cmsghdr) already aligned.
remove use CMSG_ALIGN(sizeof(struct cmsghdr)) and
CMSG_COMPAT_ALIGN(sizeof(struct compat_cmsghdr)) keep code consistent.
Signed-off-by: yuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

The USB core may call reset_resume when it fails to resume asix device.
And USB core can recovery this abnormal resume at low level driver,
the same .resume at asix driver can work too. Add .reset_resume can
avoid disconnecting after backing from system resume, and NFS can
still be mounted after this commit.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull block layer fixes from Jens Axboe:
 "A set of fixes for the current series, one fixing a regression with
  block size < page cache size in the alias series from Jan. Outside of
  that, two small cleanups for wbt from Bart, a nvme pull request from
  Christoph, and a few small fixes of documentation updates"

* 'for-linus' of git://git.kernel.dk/linux-block:
  block: fix up io_poll documentation
  block: Avoid that sparse complains about context imbalance in __wbt_wait()
  block: Make wbt_wait() definition consistent with declaration
  clean_bdev_aliases: Prevent cleaning blocks that are not in block range
  genhd: remove dead and duplicated scsi code
  block: add back plugging in __blkdev_direct_IO
  nvmet/fcloop: remove some logically dead code performing redundant ret checks
  nvmet: fix KATO offset in Set Features
  nvme/fc: simplify error handling of nvme_fc_create_hw_io_queues
  nvme/fc: correct some printk information
  nvme/scsi: Remove START STOP emulation
  nvme/pci: Delete misleading queue-wrap comment
  nvme/pci: Fix whitespace problem
  nvme: simplify stripe quirk
  nvme: update maintainers information

Pull fbdev fixes from Bartlomiej Zolnierkiewicz:

 - bring fbdev subsystem back into Maintained mode

 - add missing devm_ioremap() error checking to cobalt_lcdfb driver

* tag 'fbdev-v4.10-rc2' of git://github.com/bzolnier/linux:
  video: fbdev: cobalt_lcdfb: Handle return NULL error from devm_ioremap
  MAINTAINERS: add myself as maintainer of fbdev