This is already done in dsi node, introduced in commit eda09fe1
("arm64: dts: imx8mp: Add display pipeline components").
This needs to be applied to csi nodes as well or the clock might be busy
if both csi and dsi nodes are enabled.
Fixes error:
 clk: failed to reparent media_mipi_phy1_ref to osc_24m: -16
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This commit labels LDO5 as `reg_vdd_sdio` in `imx8mp-verdin.dtsi` to
facilitate changing its voltage to 1.8V, necessary for an SDIO
peripheral that requires 1.8V at default and high-speed modes.

Additionally, it links `reg_vdd_sdio` to `&usdhc2`, aligning with the
hardware configuration specified in the datasheet.
Signed-off-by: Philippe Schenker <philippe.schenker@impulsing.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add DTSI for Variscite VAR-SOM-MX93 System on Module and DTS for Variscite
VAR-SOM-MX93 on Symphony evaluation board.

This version comes with:
- NXP i.MX 93 Dual, 1.7GHz, Cortex-A55 + Cortex-M33
- 2 GB of RAM
- 16GB eMMC
- 802.11ax/ac/a/b/g/n WiFi with 5.3 Bluetooth
- CAN bus
- Audio codec
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Per qoriq-thermal.yaml, 'big-endian' is not a valid property.

When the 'little-endian' property is absent, the default is big endian.

Remove it to fix the following schema warning:

tmu@1f00000: 'big-endian' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/thermal/qoriq-thermal.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the TPM device found on the GW71xx revision E PCB.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the TPM device found on the GW71xx revision E PCB.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The GW71xx does not have a gpio controlled vbus regulator but it does
require some pinctrl. Remove the regulator and move the valid pinctrl
into the usbotg1 node.

Fixes: bd306fdb ("arm64: dts: imx8mm-venice-gw71xx: fix USB OTG VBUS")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the TPM device found on the GW7901 revision D PCB.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The GW7901 has GPIO's to configure the direction of its isolated
digital I/O signals. Add the GPIO pinmux and line names.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the DT node for the GPU core found on the i.MX8QXP.

etnaviv-gpu 53100000.gpu: model: GC7000, revision: 6214
[drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

It is eDMA1 at QM, which have the same register with eDMA3 at qxp.

The below commit fix panic problem.
commit b37e75bd ("arm64: dts: imx8qm: Add imx8qm's own pm to avoid panic during startup")

This fixes the IRQ and DMA channel numbers. While QM eDMA1 technically has
32 channels, only 10 channels are likely used for I2C. The exact IRQ
numbers for the remaining channels were unclear in the reference manual.

Fixes: e4d7a330 ("arm64: dts: imx8: add edma[0..3]")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

<&pd IMX_SC_R_DMA_1_CH*> is now properly aligned with the previous line
for improved code readability.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enable SAI1, add the codec to enable LINE_IN and LINE_OUT support on
MBa8Xx on connectors X9 & X10.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

These clock gates provide a clock output on ACM_MCLK_OUT pads. They are
intended to be used as MCLK for SAI0-3.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds the sai nodes attached to aips1 bus. These can be shared with
imx8qm as well. Input clock from ACM is always feed to mclk1 only. Others
are unused and are connected to a dummy clock.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The audio clock mux (ACM) selects the input clock for each attached
consumer, referenced by clock-cell.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

These clock gates provide input clocks for ACM. They can be selected by
IMX_ADMA_ACM_* macros. As SAI driver does not provide Tx/Rx bitclock
clocks yet, add dummy clocks for the unimplemented inputs.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds support for TQMa8XQP and TQMa8XDP modules on MBa8Xx board.
As the only difference is the mounted SoC, both module and baseboard
files are shared.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX 8DualXPlus is a dual (2x) Cortex-A35 processor with powerful
graphic and multimedia features. This patch adds the SoC dtsi, based on
imx8qxp removing the additional CPU cores. Peripherals are identical.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The OSM spec defines dedicated functions for all pads of the SoM.
Therefore we can assume that carrier board designs stick to these
definitions and extend the SoM devicetree include with matching
default nodes and pinmux settings.

This way we can reduce the overhead and redundancy in the carrier
board devicetrees while still sticking to the policy of separating
board and module description.

Even if the carrier board design deviates slightly from the spec it
can define its own pinmux definitions and use them as necessary or
even disable unused nodes from the SoM devicetree.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

There is an EEPROM on the SoM module. Add it to the description.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The RV3028 driver doesn't use this property. Remove it.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The PUE bit is only effective if the PE bit is also set. To avoid
confusion, disable the PUE bit if it is not needed.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The current state of the devicetree for the i.MX8MM OSM-S and the BL
baseboard reflects deprecated prototype hardware. Update the board
description to match the latest hardware revision.

As the old hardware is not available anymore, was only produced in
very small quantities and was broken in some ways, we can safely
fixup the original devicetree.

Fixes: de9618e8 ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The level of the interrupt signal is active low instead. Fix this.

Fixes: de9618e8 ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Some signals have external pullup resistors on the board and don't need
the internal ones to be enabled. Due to silicon errata ERR050080 let's
disable the internal pull resistors whererever possible and prevent
any unwanted behavior in case they wear out.

Fixes: 8668d8b2 ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Some signals have external pullup resistors on the board and don't need
the internal ones to be enabled. Due to silicon errata ERR050080 let's
disable the internal pull resistors whererever possible and prevent
any unwanted behavior in case they wear out.

Fixes: de9618e8 ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

These signals are actively driven by the SoC or by the onboard
transceiver. There's no need to enable the internal pull resistors
and due to silicon errata ERR050080 let's disable the internal ones
to prevent any unwanted behavior in case they wear out.

Fixes: 8668d8b2 ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

These signals are actively driven by the SoC or by the onboard
transceiver. There's no need to enable the internal pull resistors
and due to silicon errata ERR050080 let's disable the internal ones
to prevent any unwanted behavior in case they wear out.

Fixes: de9618e8 ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

There are external pullup resistors on the board and due to silicon
errata ERR050080 let's disable the internal ones to prevent any
unwanted behavior in case they wear out.

Fixes: 8668d8b2 ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

There are external pullup resistors on the board and due to silicon
errata ERR050080 let's disable the internal ones to prevent any
unwanted behavior in case they wear out.

Fixes: de9618e8 ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pull more bcachefs updates from Kent Overstreet:
 "Some fixes, Some refactoring, some minor features:

   - Assorted prep work for disk space accounting rewrite

   - BTREE_TRIGGER_ATOMIC: after combining our trigger callbacks, this
     makes our trigger context more explicit

   - A few fixes to avoid excessive transaction restarts on
     multithreaded workloads: fstests (in addition to ktest tests) are
     now checking slowpath counters, and that's shaking out a few bugs

   - Assorted tracepoint improvements

   - Starting to break up bcachefs_format.h and move on disk types so
     they're with the code they belong to; this will make room to start
     documenting the on disk format better.

   - A few minor fixes"

* tag 'bcachefs-2024-01-21' of https://evilpiepirate.org/git/bcachefs: (46 commits)
  bcachefs: Improve inode_to_text()
  bcachefs: logged_ops_format.h
  bcachefs: reflink_format.h
  bcachefs; extents_format.h
  bcachefs: ec_format.h
  bcachefs: subvolume_format.h
  bcachefs: snapshot_format.h
  bcachefs: alloc_background_format.h
  bcachefs: xattr_format.h
  bcachefs: dirent_format.h
  bcachefs: inode_format.h
  bcachefs; quota_format.h
  bcachefs: sb-counters_format.h
  bcachefs: counters.c -> sb-counters.c
  bcachefs: comment bch_subvolume
  bcachefs: bch_snapshot::btime
  bcachefs: add missing __GFP_NOWARN
  bcachefs: opts->compression can now also be applied in the background
  bcachefs: Prep work for variable size btree node buffers
  bcachefs: grab s_umount only if snapshotting
  ...

Pull timer updates from Thomas Gleixner:
 "Updates for time and clocksources:

   - A fix for the idle and iowait time accounting vs CPU hotplug.

     The time is reset on CPU hotplug which makes the accumulated
     systemwide time jump backwards.

   - Assorted fixes and improvements for clocksource/event drivers"

* tag 'timers-core-2024-01-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick-sched: Fix idle and iowait sleeptime accounting vs CPU hotplug
  clocksource/drivers/ep93xx: Fix error handling during probe
  clocksource/drivers/cadence-ttc: Fix some kernel-doc warnings
  clocksource/drivers/timer-ti-dm: Fix make W=n kerneldoc warnings
  clocksource/timer-riscv: Add riscv_clock_shutdown callback
  dt-bindings: timer: Add StarFive JH8100 clint
  dt-bindings: timer: thead,c900-aclint-mtimer: separate mtime and mtimecmp regs

Pull powerpc fixes from Aneesh Kumar:

 - Increase default stack size to 32KB for Book3S

Thanks to Michael Ellerman.

* tag 'powerpc-6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64s: Increase default stack size to 32KB

Add line breaks - inode_to_text() is now much easier to read.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>