Remove some dead code now that RX pools are being cleaned. This
was included to wait until any pending RX queue interrupts are
processed, but NAPI polling should be disabled by this point.

Another minor change is to use the net device parameter for any
print functions instead of accessing it from the adapter structure.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When sending a packet to a tunnel device, the dev's hard_header_len
could be larger than the skb->len in function packet_length().
In the case of ip6gretap/erspan, hard_header_len = LL_MAX_HEADER + t_hlen,
which is around 180, and an ARP packet sent to this tunnel has
skb->len = 42.  This causes the 'unsign int length' to become super
large because it is negative value, causing the later ovs_vport_send
to drop it due to over-mtu size.  The patch fixes it by setting it to 0.
Signed-off-by: William Tu <u9012063@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kirill Tkhai says:

====================
Converting pernet_operations (part #5)

this series continues to review and to convert pernet_operations
to make them possible to be executed in parallel for several
net namespaces in the same time. There are mostly netfilter
operations (and they should be the last netfilter's), also
there are two patches touching pktgen and xfrm.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

These pernet_operations are similar to ipv4_net_ops.
They are safe to be async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These pernet_operations register and unregister bunch
of nf_conntrack_l4proto. Exit method unregisters related
sysctl, init method calls init_net and get_net_proto.
The whole builtin_l4proto4 array has pretty simple
init_net and get_net_proto methods. The first one register
sysctl table, the second one is just RO memory dereference.
So, these pernet_operations are safe to be marked as async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These pernet_operations unregister net::ipv4::iptable_security table.
Another net/pernet_operations do not send ipv4 packets to foreign
net namespaces. So, we mark them async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These pernet_operations unregister net::ipv4::iptable_raw table.
Another net/pernet_operations do not send ipv4 packets to foreign
net namespaces. So, we mark them async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These pernet_operations unregister net::ipv4::nat_table table.
Another net/pernet_operations do not send ipv4 packets to foreign
net namespaces. So, we mark them async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These pernet_operations unregister net::ipv4::iptable_mangle table.
Another net/pernet_operations do not send ipv4 packets to foreign
net namespaces. So, we mark them async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These pernet_operations unregister net::ipv4::arptable_filter.
Another net/pernet_operations do not send arp packets to foreign
net namespaces. So, we mark them async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These pernet_operations create per-net pktgen threads
and /proc entries. These pernet subsys looks closed
in itself, and there are no pernet_operations outside
this file, which are interested in the threads.
Init and/or exit methods look safe to be executed
in parallel.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These pernet_operations register and unregister net::nf::queue_handler
and /proc entry. The handler is accessed only under RCU, so this looks
safe to convert them.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These pernet_operations create and destroy /proc entries.
Also, exit method unsets nfulnl_logger. The logger is not
set by default, and it becomes bound via userspace request.
So, they look safe to be made async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These pernet_operations also look closed in themself.
Exit method touch only per-net structures, so it's
safe to execute them for several net namespaces in parallel.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These pernet_operations look closed in themself,
and there are no other users of net::nfnl_acct_list
outside. They are safe to be executed for several
net namespaces in parallel.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These pernet_operations create and destroy net::nfnl
socket of NETLINK_NETFILTER code. There are no other
places, where such type the socket is created, except
these pernet_operations. It seem other pernet_operations
depending on CONFIG_NETFILTER_NETLINK send messages
to this socket. So, we mark it async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These pernet_operations looks nicely separated per-net.
Exit method unregisters net's nf tables objects.
We allow them be executed in parallel.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These pernet_operations create and destroy net::xfrm::nlsk
socket of NETLINK_XFRM. There is only entry point, where
it's dereferenced, it's xfrm_user_rcv_msg(). There is no
in-kernel senders to this socket.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The pernet_operations:

    ip6table_filter_net_ops
    ip6table_mangle_net_ops
    ip6table_nat_net_ops
    ip6table_raw_net_ops
    ip6table_security_net_ops

have exit methods, which call ip6t_unregister_table().
ip6table_filter_net_ops has init method registering
filter table.

Since there must not be in-flight ipv6 packets at the time
of pernet_operations execution and since pernet_operations
don't send ipv6 packets each other, these pernet_operations
are safe to be async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow setting firstfrag as matching option in tc flower classifier.

 # tc filter add dev eth0 protocol ip parent ffff: \
     flower indev eth0 \
        ip_flags firstfrag
     action mirred egress redirect dev eth1
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Peng Li says:

====================
fix some bugs for hns3 driver

This patchset fix some bugs for hns3 driver.
[Patch 1/6 - Patch 3/6] fix bugs related about VF driver.
[Patch 3/6 - Patch 6/6] fix the bugs about ethtool_ops.set_channels.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for VF driver inner interface
hclgevf_ops.get_tqps_and_rss_info. This interface will be
used in the initialization process.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

HNS3 driver should alloc netdev with max support ring num, as
driver support change netdev count by ethtool -L.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Command HCLGE_OPC_CFG_COM_TQP_QUEUE should use queue id in the
function, but command HCLGE_OPC_RESET_TQP_QUEUE should use global
queue id.
This patch fixes the queue id about queue enable/disable/reset.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the endian issue when PF get mbx message flag.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver check the out_vld bit when get a new cmdq BD, if the bit is 1,
the BD is valid. driver Should set the bit 0 after used and hw will
set the bit 1 if get a valid BD.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VF driver should get the real rss_size which is assigned
by host PF, not rss_size_max.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Let dpipe/resource be retrieved by unprivileged users.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We miss CONFIG_* fragments so test fib-onlink-tests.sh can do:
ip li add lisa type vrf table 1101
ip li add veth1 type veth peer name veth2

And the follow message occurs if it isn't enabled:
Configuring interfaces
RTNETLINK answers: Operation not supported

This enables for NET_NRF (and friends) and VETH so we can create a vrf
table and veth.

Fixes: 153e1b84 ("selftests: Add FIB onlink tests")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The rx_handler field is rcu-protected, but I forgot to use the
proper accessor while refactoring netif_is_ipvlan_port(). Such
function only check the rx_handler value, so it is safe, but we need
to properly read rx_handler via rcu_access_pointer() to avoid sparse
warnings.

Fixes: 1ec54cb4 ("net: unpollute priv_flags space")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kirill found that recently added synchronize_rcu() call in
ip6mr_sk_done()
was slowing down netns dismantle and posted a patch to use it only if
the socket
was found.

I instead suggested to get rid of this call, and use instead
SOCK_RCU_FREE

We might later change IPv4 side to use the same technique and unify
both stacks. IPv4 does not use synchronize_rcu() but has a call_rcu()
that could be replaced by SOCK_RCU_FREE.

Tested:
 time for i in {1..1000}; do unshare -n /bin/false;done

 Before : real 7m18.911s
 After : real 10.187s

Fixes: 8571ab47 ("ip6mr: Make mroute_sk rcu-based")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Cc: Yuval Mintz <yuvalm@mellanox.com>
Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sowmini Varadhan says:

====================
RDS: zerocopy code enhancements

A couple of enhancements to the rds zerocop code
- patch 1 refactors rds_message_copy_from_user to pull the zcopy logic
  into its own function
- patch 2 drops the usage sk_buff to track MSG_ZEROCOPY cookies and
  uses a simple linked list (enhancement suggested by willemb during
  code review)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 401910db ("rds: deliver zerocopy completion notification
with data") removes support fo r zerocopy completion notification
on the sk_error_queue, thus we no longer need to track the cookie
information in sk_buff structures.

This commit removes the struct sk_buff_head rs_zcookie_queue by
a simpler list that results in a smaller memory footprint as well
as more efficient memory_allocation time.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the large block of code predicated on zcopy from
rds_message_copy_from_user into a new function,
rds_message_zcopy_from_user()
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove VLA usage and change the 'len' argument to a u8 and use a 256
byte buffer on the stack. Notice that these lengths are limited by the
encoding field in the VPD structure, which is a u8 [1].

[1] https://marc.info/?l=linux-netdev&m=152044354814024&w=2Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the SO_ZEROCOPY switch case on sock_setsockopt() avoiding the
ret values to be overwritten by the one set on the default case.

Fixes: 28190752 ("sock: permit SO_ZEROCOPY on PF_RDS socket")
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Maxime Chevallier says:

====================
net: mvpp2: Add Unicast filtering capabilities

This series adds unicast filtering support to the Marvell PPv2 controller.

This is implemented using the header parser cababilities of the PPv2,
which allows for generic packet filtering based on matching patterns in
the packet headers.

PPv2 controller only has 256 of these entries, and we need to share them
with other features, such as VLAN filtering.

For each interface, we have 5 entries dedicated to unicast filtering (the
controller's own address, and 4 other), and 21 to multicast filtering.

When this number is reached, the controller switches to unicast or
multicast promiscuous mode.

The first patch reworks the function that adds and removes addresses to the
filter. This is preparatory work to ease UC filter implementation.

The second patch adds the UC filtering feature.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Marvell PPv2 controller can be used to implement packet filtering based
on the destination MAC address. This is already used to implement
multicast filtering. This patch adds support for Unicast filtering.

Filtering is based on so-called "TCAM entries" to implement filtering.
Due to their limited number and the fact that these are also used for
other purposes, we reserve 80 entries for both unicast and multicast
filters. On top of the broadcast address, and each interface's own MAC
address, we reserve 25 entries per port, 4 for unicast filters, 21 for
multicast.

Whenever unicast or multicast range for one port is full, the filtering
is disabled and port goes into promiscuous mode for the given type of
addresses.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mvpp2_prs_mac_da_accept function takes into parameter both the
struct representing the controller and the port id. This is meaningful
when we want to create TCAM entries for non-initialized ports, but in
this case we expect the port to be initialized before starting adding or
removing MAC addresses to the per-port filter.

This commit changes the function so that it takes struct mvpp2_port as
a parameter instead.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix copy&paste error and pass proper flags.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>