Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add separate function for rf init calibration code and use it
on all init rf subroutines.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge code which program the same registes at the end of rfcsr
initialization for 5592, 5392 and 5390 chips.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In some cases it can be useful to change the MAC address of a virtual
interface to something that's completely different from the EEPROM
stored MAC address. In this case it is a bad idea to use the EEPROM MAC
address for calculating the BSSID mask, as that would make it too wide.

In one case a few devices have been observed to send ACKs for many
packets on the channel not directed at them, which results in a neat
Denial of Service attack on the channel.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Preparation for updating common->macaddr along with virtual interface
MAC address changes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is called with spinlocks held so we have to use GFP_ATOMIC.  It's
the sc_pcu_lock in ath9k_stop() that's the issue.  The call tree looks
like this:

ath9k_stop()
ath_prepare_reset()
ath_stoprecv()
ath_flushrecv()
ath_rx_tasklet()
ath9k_dfs_process_phyerr()
pd->add_pulse() => dpd_add_pulse()
channel_detector_get()
channel_detector_create()
pri_detector_init()

channel_detector_create() uses GFP_ATOMIC as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Acked-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The DFS pattern detector was initially planned to reside on
a higher layer and used generic pr_*() logging functions.

Being part of ath9k, use ath_dbg() instead and make DFS log
ouput selectable via ATH_DBG_DFS (0x20000) at runtime.

This patch does not contain functional modifications.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some cards on Ralink RT30xx chipset not have correctly TX_MIXER_GAIN
value in them EEPROM/EFUSE. In this case, we must use default value,
but always used EEPROM/EFUSE value. As result we have tranmitt power
range from -10dBm to +6dBm instead 0dBm to +16dBm.

Correctly value in EEPROM/EFUSE is one or more for RT3070 and two or
more for other RT30xx chips.

Tested on Canyon CNP-WF518N1 usb Wi-Fi dongle and Jorjin WN8020 usb
embedded Wi-Fi module.
Signed-off-by: Alex A. Mihaylov <minimumlaw@rambler.ru>
Cc: stable@vger.kernel.org
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This rate causes an overflow in the extended rates IE's data rate field,
with the overflowing bit setting the Basic Rate Set membership. This
results in a bogus 8 Mpbs basic rate, making clients checking them refuse
association.

Since the rate is likely unused anyway (HT will yield better rates between
supporting chips), we can just remove it.

This fixes association from wpa_supplicant and Android 4.x and newer.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Samuel Ortiz <sameo@linux.intel.com> says:

"This is the 2nd NFC pull request for 3.10.

With this one we have:

- A major pn533 update. The pn533 framing support has been changed in order to
  easily support all pn533 derivatives. For example we now support the ACR122
  USB dongle.

- An NFC MEI physical layer code factorization through the mei_phy NFC API.
  Both the microread and the pn544 drivers now use it.

- LLCP aggregation support. This allows NFC p2p devices to send aggregated
  frames containing all sort of LLCP frames except SYMM and aggregation
  frames.

- More LLCP socket options for getting the remote device link parameters.

- Fixes for the LLCP socket option code added with the first pull request for
  3.10.

- Some support for LLCP corner cases like 0 length SDUs and general DISC
  (tagged with a 0,0 dsap ssap couple) handling.

- RFKILL support for NFC."
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Pass the rate selection table to mac80211 from minstrel_update_stats.
Only rates for sample attempts are set in info->control.rates, with deferred
sampling, only the second slot gets changed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Pass the rate selection table to mac80211 from minstrel_ht_update_stats.
Only rates for sample attempts are set in info->control.rates.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Allow rate control modules to pass a rate selection table to mac80211
and the driver. This allows drivers to fetch the most recent rate
selection from the sta pointer for already buffered frames. This allows
rate control to respond faster to sudden link changes and it is also a
step towards adding minstrel_ht support to drivers like iwlwifi.

When a driver sets IEEE80211_HW_SUPPORTS_RC_TABLE, mac80211 will not
fill info->control.rates with rates from the rate table (to preserve
explicit overrides by the rate control module). The driver then
explicitly calls ieee80211_get_tx_rates to merge overrides from
info->control.rates with defaults from the sta rate table.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Some protocols need a more reliable connection to complete
successful in reasonable time. This patch adds a user-space
API to indicate the wireless driver that a critical protocol
is about to commence and when it is done, using nl80211 primitives
NL80211_CMD_CRIT_PROTOCOL_START and NL80211_CRIT_PROTOCOL_STOP.

There can be only on critical protocol session started per
registered cfg80211 device.

The driver can support this by implementing the cfg80211 callbacks
.crit_proto_start() and .crit_proto_stop(). Examples of protocols
that can benefit from this are DHCP, EAPOL, APIPA. Exactly how the
link can/should be made more reliable is up to the driver. Things
to consider are avoid scanning, no multi-channel operations, and
alter coexistence schemes.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Initialize {mp,mi}->{max_tp_rate,max_tp_rate2,max_prob_rate} in
minstrel_ht's rate_init and rate_update.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

minstrel_ht initializes max_tp_rate max_tp_rate2 and max_prob_rate to
zero both for minstrel_ht_sta and minstrel_mcs_group_data.
This is wrong since there is no guarantee that the 1st rate of any
group is supported.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
[fix some indentation on the way]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The RCU docs used to state that rcu_barrier() included a wait
for an RCU grace period; however the comments for rcu_barrier()
as of commit f0a0e6f2... "rcu: Clarify memory-ordering properties
of grace-period primitives" contradict this.

So add back synchronize_{rcu,net}() to where they once were,
but keep the rcu_barrier()s for the call_rcu() callbacks.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bob Copeland <bob@cozybit.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Some driver implementations need to know whether mandatory
admission control is required by the AP for some ACs. Add
a parameter to the TX queue parameters indicating this.

As there's currently no support for admission control in
mac80211's AP implementation, it's only ever set for the
client implementation.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In cfg80211_can_use_iftype_chan(), check for P2P Device
first, and then for netdevs. This doesn't really change
anything but makes the code a bit easier to read since
it may not be obvious for everyone at first that a P2P
device has no netdev.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211_stop_p2p_device() requires the devlist_mtx to
be held, but nl80211_stop_p2p_device() doesn't acquire
it which is a locking error and causes a warning (when
lockdep is enabled). Fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Most dump callbacks, including the scan results one, use
the netdev to identify what to do, which is incorrect for
the P2P_DEVICE support, it needs to be able to get the
scan result from the wdev. Change all dumps to unify the
code, but ones other than scan don't really support being
executed on a wdev that has no netdev.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There's an issue in receiving broadcast management frames
on P2P Device virtual interfaces, such frames have the RX
flag IEEE80211_RX_RA_MATCH cleared and are thus dropped
in ieee80211_rx_h_mgmt_check(). They should be let through
to make it to ieee80211_rx_h_userspace_mgmt() and then to
userspace.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This patch renames LE_SCANNING_ENABLED and LE_SCANNING_DISABLED
macros to LE_SCAN_ENABLE and LE_SCAN_DISABLE in order to keep
the same prefix others LE scan macros have.

It also fixes le_scan_enable_req function so it uses the LE_SCAN_
ENABLE macro instead of a magic number.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

This patch adds macros for filter_duplicates parameter values from
HCI LE Set Scan Enable command. It also fixes le_scan_enable_req
function so it uses the LE_SCAN_FILTER_DUP_ENABLE macro instead of
a magic number.

The LE_SCAN_FILTER_DUP_DISABLE was also defined since it will be
required to properly support the GAP Observer Role.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

This patch adds macros for active and passive LE scan type values.
The LE_SCAN_PASSIVE was also defined since it will be used in future
by LE connection routine and GAP Observer Role support.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Define LE scanning timeout macros in jiffies just like we do for
others timeout macros.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

With the introduction of CSA4 there is now also a features page number 2
available. This patch increments the maximum supported page number to 2
and adds code for reading all available pages (as long as we have
support for them - indicated by HCI_MAX_PAGES).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

The local and remote features are organized by page number. Page 0
are the LMP features, page 1 the host features, and any pages beyond 1
features that future core specification versions may define. So far
we've only had the first two pages and two separate variables has been
convenient enough, however with the introduction of Core Specification
Addendum 4 there are features defined on page 2.

Instead of requiring the addition of a new variable each time a new page
number is defined, this patch refactors the code to use a single table
for the features. The patch needs to update both the hci_dev and
hci_conn structures since there are macros that depend on the features
being represented in the same way in both of them.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Since this function is only used by sco, move it from hci_event.c to
sco.c and rename to sco_conn_defer_accept. Make it static.
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Some faulty non SSP devices send extended inquiry response
during device discovery which is a violation of 2.1 specification.
So for these devices we set SSP bit during acl connection
initiation thinking that it is an SSP device. But for these
devices, in remote host features event SSP supported bit
will be off. But we are not clearing the SSP bit in that case
and eventually SSP bit in conn flag will be incorrectly set for
these devices.

The software which has caused this issue is MecApp
http://www.mecel.se/products/bluetooth/downloads/MecApp_download

This patch does a workaround by clearing the SSP bit if it is
not supported in remote host features event

hcidump log
----------

< HCI Command: Inquiry (0x01|0x0001) plen 5
    lap 0x9e8b33 len 4 num 0
> HCI Event: Command Status (0x0f) plen 4
    Inquiry (0x01|0x0001) status 0x00 ncmd 1
> HCI Event: Extended Inquiry Result (0x2f) plen 255
    bdaddr 00:1B:DC:05:B5:25 mode 1 clkoffset 0x3263 class 0x3c0000 rssi -77
    Unknown type 0x42 with 8 bytes data
    Unknown type 0x1e with 2 bytes data
> HCI Event: Inquiry Complete (0x01) plen 1
    status 0x00

< HCI Command: Create Connection (0x01|0x0005) plen 13
    bdaddr 00:1B:DC:05:B5:25 ptype 0xcc18 rswitch 0x01 clkoffset 0x0000
    Packet type: DM1 DM3 DM5 DH1 DH3 DH5
> HCI Event: Command Status (0x0f) plen 4
    Create Connection (0x01|0x0005) status 0x00 ncmd 1
> HCI Event: Connect Complete (0x03) plen 11
    status 0x00 handle 12 bdaddr 00:1B:DC:05:B5:25 type ACL encrypt 0x00
< HCI Command: Read Remote Supported Features (0x01|0x001b) plen 2
    handle 12
> HCI Event: Command Status (0x0f) plen 4
    Read Remote Supported Features (0x01|0x001b) status 0x00 ncmd 1
> HCI Event: Read Remote Supported Features (0x0b) plen 11
    status 0x00 handle 12
    Features: 0xff 0xff 0x8f 0x7e 0xd8 0x1f 0x5b 0x87
< HCI Command: Read Remote Extended Features (0x01|0x001c) plen 3
    handle 12 page 1
> HCI Event: Command Status (0x0f) plen 4
    Read Remote Extended Features (0x01|0x001c) status 0x00 ncmd 1
> HCI Event: Page Scan Repetition Mode Change (0x20) plen 7
    bdaddr 00:1B:DC:05:B5:25 mode 1
> HCI Event: Max Slots Change (0x1b) plen 3
    handle 12 slots 5
> HCI Event: Read Remote Extended Features (0x23) plen 13
    status 0x00 handle 12 page 1 max 0
    Features: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
< HCI Command: Remote Name Request (0x01|0x0019) plen 10
    bdaddr 00:1B:DC:05:B5:25 mode 2 clkoffset 0x0000
> HCI Event: Command Status (0x0f) plen 4
    Remote Name Request (0x01|0x0019) status 0x00 ncmd 1
> HCI Event: Remote Name Req Complete (0x07) plen 255
    status 0x00 bdaddr 00:1B:DC:05:B5:25 name 'Bluetooth PTS Radio v4'
< HCI Command: Authentication Requested (0x01|0x0011) plen 2
    handle 12
> HCI Event: Command Status (0x0f) plen 4
    Authentication Requested (0x01|0x0011) status 0x00 ncmd 1
> HCI Event: Link Key Request (0x17) plen 6
    bdaddr 00:1B:DC:05:B5:25
< HCI Command: Link Key Request Negative Reply (0x01|0x000c) plen 6
    bdaddr 00:1B:DC:05:B5:25
> HCI Event: Command Complete (0x0e) plen 10
    Link Key Request Negative Reply (0x01|0x000c) ncmd 1
    status 0x00 bdaddr 00:1B:DC:05:B5:25
> HCI Event: PIN Code Request (0x16) plen 6
    bdaddr 00:1B:DC:05:B5:25
Signed-off-by: Jaganath Kanakkassery <jaganath.k@samsung.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Use powers of two in ewma of minstrel.
This changes :
- EWMA_DIV   from 100 to 2^7
- EWMA_LEVEL from 75 (/EWMA_DIV=100) to 2^6 + 2^5 (/EWMA_DIV=128)

Note that this changes EWMA_DIV - EWMA_LEVEL from 25 to 2^5 and keeps
EWMA_LEVEL / EWMA_DIV == 0.75.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This changes the minstrel stats ouput from:

rate     throughput  ewma prob   this prob  this succ/attempt   success    attempts
 BCD   6         0.0        0.0        0.0          0(  0)          0           0

to:

rate      throughput  ewma prob  this prob  this succ/attempt   success    attempts
 BCD   6         0.0        0.0        0.0             0(  0)         0           0
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since Stanislaw's patches, when suspending while connected,
cfg80211 will disconnect. This causes the AP station to be
removed, which uses call_rcu() to clean up. Due to needing
process context, this queues a work struct on the mac80211
workqueue. This will warn and fail when already suspended,
which can happen if the rcu call doesn't happen quickly.

To fix this, replace the synchronize_net() which is really
just synchronize_rcu_expedited() with rcu_barrier(), which
unlike synchronize_rcu() waits until RCU callback have run
and thus avoids this issue.

In theory, this can even happen without Stanislaw's change
to disconnect on suspend since userspace might disconnect
just before suspending, though then it's unlikely that the
call_rcu() will be delayed long enough.

Cc: stable@vger.kernel.org [3.7+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

According to the specifications, data output reports must be sent on the
interrupt channel. See also usbhid implementation.
Sending these reports on the control channel breaks newer Wii Remotes.

Note that this will make output reports asynchronous. However, that's how
hid_output_raw_report() is supposed to work with HID_OUTPUT_REPORT as
report type. There are no responses to output reports.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

If a device is registered as HID device, it is always in Report-Mode.
Therefore, we must not send Boot-Protocol messages on
hidinput_input_event() callbacks. This confuses devices and may cause
disconnects on protocol errors.

We disable the hidinput_input_event() callback for now. We can implement
it properly later, but lets first fix the current code by disabling it.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>