- 30 Mar, 2017 40 commits
-
-
Ankur Arora authored
commit 1914f0cd upstream. This was broken in commit cd979883 ("xen/acpi-processor: fix enabling interrupts on syscore_resume"). do_suspend (from xen/manage.c) and thus xen_resume_notifier never get called on the initial-domain at resume (it is if running as guest.) The rationale for the breaking change was that upload_pm_data() potentially does blocking work in syscore_resume(). This patch addresses the original issue by scheduling upload_pm_data() to execute in workqueue context. Cc: Stanislaw Gruszka <sgruszka@redhat.com> Based-on-patch-by:
Konrad Wilk <konrad.wilk@oracle.com> Reviewed-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
Ankur Arora <ankur.a.arora@oracle.com> Signed-off-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alex Williamson authored
commit 65b1adeb upstream. The intent of the original warning is make sure that the mdev vendor driver has removed any group notifiers at the point where the group is closed by the user. Theoretically this would be through an orderly shutdown where any devices are release prior to the group release. We can't always count on an orderly shutdown, the user can close the group before the notifier can be removed or the user task might be killed. We'd like to add this sanity test when the group is idle and the only references are from the devices within the group themselves, but we don't have a good way to do that. Instead check both when the group itself is removed and when the group is opened. A bit later than we'd prefer, but better than the current over aggressive approach. Fixes: ccd46dba ("vfio: support notifier chain in vfio_group") Signed-off-by:
Alex Williamson <alex.williamson@redhat.com> Cc: Jike Song <jike.song@intel.com> Signed-off-by:
-
Eric Biggers authored
commit 1b53cf98 upstream. Filesystem encryption ostensibly supported revoking a keyring key that had been used to "unlock" encrypted files, causing those files to become "locked" again. This was, however, buggy for several reasons, the most severe of which was that when key revocation happened to be detected for an inode, its fscrypt_info was immediately freed, even while other threads could be using it for encryption or decryption concurrently. This could be exploited to crash the kernel or worse. This patch fixes the use-after-free by removing the code which detects the keyring key having been revoked, invalidated, or expired. Instead, an encrypted inode that is "unlocked" now simply remains unlocked until it is evicted from memory. Note that this is no worse than the case for block device-level encryption, e.g. dm-crypt, and it still remains possible for a privileged user to evict unused pages, inodes, and dentries by running 'sync; echo 3 > /proc/sys/vm/drop_caches', or by simply unmounting the filesystem. In fact, one of those actions was already needed anyway for key revocation to work even somewhat sanely. This change is not expected to break any applications. In the future I'd like to implement a real API for fscrypt key revocation that interacts sanely with ongoing filesystem operations --- waiting for existing operations to complete and blocking new operations, and invalidating and sanitizing key material and plaintext from the VFS caches. But this is a hard problem, and for now this bug must be fixed. This bug affected almost all versions of ext4, f2fs, and ubifs encryption, and it was potentially reachable in any kernel configured with encryption support (CONFIG_EXT4_ENCRYPTION=y, CONFIG_EXT4_FS_ENCRYPTION=y, CONFIG_F2FS_FS_ENCRYPTION=y, or CONFIG_UBIFS_FS_ENCRYPTION=y). Note that older kernels did not use the shared fs/crypto/ code, but due to the potential security implications of this bug, it may still be worthwhile to backport this fix to them. Fixes: b7236e21 ("ext4 crypto: reorganize how we store keys in the inode") Signed-off-by:
Eric Biggers <ebiggers@google.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Acked-by:
Michael Halcrow <mhalcrow@google.com> Signed-off-by:
-
Gary R Hook authored
commit 7c468447 upstream. The CCP driver generally uses a round-robin approach when assigning operations to available CCPs. For the DMA engine, however, the DMA mappings of the SGs are associated with a specific CCP. When an IOMMU is enabled, the IOMMU is programmed based on this specific device. If the DMA operations are not performed by that specific CCP then addressing errors and I/O page faults will occur. Update the CCP driver to allow a specific CCP device to be requested for an operation and use this in the DMA engine support. Signed-off-by:
Gary R Hook <gary.hook@amd.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Ryan Hsu authored
commit 6be3b6cc upstream. In the 'commit ebee76f7 ("ath10k: allow setting coverage class")', it inherits the design and the address offset from ath9k, but the address is not applicable to QCA6174, which leads to a random crash while doing the resume() operation, since the set_coverage_class.ops will be called from ieee80211_reconfig() when resume() (if the wow is not configured). Fix the incorrect address offset here to avoid the random crash. Verified on QCA6174/hw3.0 with firmware WLAN.RM.4.4-00022-QCARMSWPZ-2. kvalo: this also seems to fix a regression with firmware restart. Fixes: ebee76f7 ("ath10k: allow setting coverage class") Signed-off-by:
Ryan Hsu <ryanhsu@qca.qualcomm.com> Signed-off-by:
Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by:
-
Brian Norris authored
commit 4e841d3e upstream. When PCIe FLR support was added, much of the remove/release code for PCIe was migrated to ->down_dev(), but ->down_dev() is never called for device removal. Let's refactor the cleanup to be done in both cases. Also, drop the comments above mwifiex_cleanup_pcie(), because they were clearly wrong, and it's better to have clear and obvious code than to detail the code steps in comments anyway. Fixes: 4c5dae59 ("mwifiex: add PCIe function level reset support") Signed-off-by:
Brian Norris <briannorris@chromium.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Chen-Yu Tsai authored
commit ac8616e4 upstream. The MP style clocks support an mux with pre-dividers. While the driver correctly accounted for them in the .determine_rate callback, it did not in the .recalc_rate and .set_rate callbacks. This means when calculating the factors in the .set_rate callback, they would be off by a factor of the active pre-divider. Same goes for reading back the clock rate after it is set. Fixes: 2ab836db ("clk: sunxi-ng: Add M-P factor clock support") Signed-off-by:
Chen-Yu Tsai <wens@csie.org> Signed-off-by:
Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by:
-
Chen-Yu Tsai authored
commit 9ad0bb39 upstream. The enable bit offset for the hdmi-ddc module clock is wrong. It is pointing to the main hdmi module clock enable bit. Reported-by:
Bob Ham <rah@settrans.net> Fixes: c6e6c96d ("clk: sunxi-ng: Add A31/A31s clocks") Signed-off-by:
-
Prarit Bhargava authored
commit 8c75704e upstream. After commit e9afc746 ("hwrng: geode - Use linux/io.h instead of asm/io.h") the geode-rng driver uses devres with pci_dev->dev to keep track of resources, but does not actually register a PCI driver. This results in the following issues: 1. The driver leaks memory because the driver does not attach to a device. The driver only uses the PCI device as a reference. devm_*() functions will release resources on driver detach, which the geode-rng driver will never do. As a result, 2. The driver cannot be reloaded because there is always a use of the ioport and region after the first load of the driver. Revert the changes made by e9afc746 ("hwrng: geode - Use linux/io.h instead of asm/io.h"). Signed-off-by:
Prarit Bhargava <prarit@redhat.com> Fixes: 6e9b5e76 ("hwrng: geode - Migrate to managed API") Cc: Matt Mackall <mpm@selenic.com> Cc: Corentin LABBE <clabbe.montjoie@gmail.com> Cc: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com> Cc: Wei Yongjun <weiyongjun1@huawei.com> Cc: linux-crypto@vger.kernel.org Cc: linux-geode@lists.infradead.org Signed-off-by:
-
Prarit Bhargava authored
commit 69db7009 upstream. After commit 31b2a73c ("hwrng: amd - Migrate to managed API"), the amd-rng driver uses devres with pci_dev->dev to keep track of resources, but does not actually register a PCI driver. This results in the following issues: 1. The message WARNING: CPU: 2 PID: 621 at drivers/base/dd.c:349 driver_probe_device+0x38c is output when the i2c_amd756 driver loads and attempts to register a PCI driver. The PCI & device subsystems assume that no resources have been registered for the device, and the WARN_ON() triggers since amd-rng has already do so. 2. The driver leaks memory because the driver does not attach to a device. The driver only uses the PCI device as a reference. devm_*() functions will release resources on driver detach, which the amd-rng driver will never do. As a result, 3. The driver cannot be reloaded because there is always a use of the ioport and region after the first load of the driver. Revert the changes made by 31b2a73c ("hwrng: amd - Migrate to managed API"). Signed-off-by:
-
Adrian Hunter authored
commit 027fb89e upstream. Disabling interrupts for even a millisecond can cause problems for some devices. That can happen when Intel host controllers wait for the present state to propagate. The spin lock is not necessary here. Anything that is racing with changes to the I/O state is already broken. The mmc core already provides synchronization via "claiming" the host. Although the spin lock probably should be removed from the code paths that lead to this point, such a patch would touch too much code to be suitable for stable trees. Consequently, for this patch, just drop the spin lock while waiting. Signed-off-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Tested-by:
Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by:
-
Adrian Hunter authored
commit e2ebfb21 upstream. Disabling interrupts for even a millisecond can cause problems for some devices. That can happen when sdhci changes clock frequency because it waits for the clock to become stable under a spin lock. The spin lock is not necessary here. Anything that is racing with changes to the I/O state is already broken. The mmc core already provides synchronization via "claiming" the host. Although the spin lock probably should be removed from the code paths that lead to this point, such a patch would touch too much code to be suitable for stable trees. Consequently, for this patch, just drop the spin lock while waiting. Signed-off-by:
-
Anssi Hannula authored
commit 16681037 upstream. sdhci_arasan_get_timeout_clock() divides the frequency it has with (1 << (13 + divisor)). However, the divisor is not some Arasan-specific value, but instead is just the Data Timeout Counter Value from the SDHCI Timeout Control Register. Applying it here like this is wrong as the sdhci driver already takes that value into account when calculating timeouts, and in fact it *sets* that register value based on how long a timeout is wanted. Additionally, sdhci core interprets the .get_timeout_clock callback return value as if it were read from hardware registers, i.e. the unit should be kHz or MHz depending on SDHCI_TIMEOUT_CLK_UNIT capability bit. This bit is set at least on the tested Zynq-7000 SoC. With the tested hardware (SDHCI_TIMEOUT_CLK_UNIT set) this results in too high a timeout clock rate being reported, causing the core to use longer-than-needed timeouts. Additionally, on a partitioned MMC (therefore having erase_group_def bit set) mmc_calc_max_discard() disables discard support as it looks like controller does not support the long timeouts needed for that. Do not apply the extra divisor and return the timeout clock in the expected unit. Tested with a Zynq-7000 SoC and a partitioned Toshiba THGBMAG5A1JBAWR eMMC card. Signed-off-by:
Anssi Hannula <anssi.hannula@bitwise.fi> Fixes: e3ec3a3d ("mmc: arasan: Add driver for Arasan SDHCI") Signed-off-by:
-
Romain Izard authored
commit 2ce0c7b6 upstream. The SDHCI controller in the SAMA5D2 chip requires a valid voltage set in the power control register, otherwise commands will fail with a timeout error. When using the regulator framework to specify the regulator used by the mmc device, the voltage is not configured, and it is not possible to use the connected device. Implement a custom 'set_power' function for this specific hardware, that configures the voltage in the register in all cases. Signed-off-by:
Romain Izard <romain.izard.pro@gmail.com> Acked-by:
-
Paul Moore authored
commit 5b52330b upstream. What started as a rather straightforward race condition reported by Dmitry using the syzkaller fuzzer ended up revealing some major problems with how the audit subsystem managed its netlink sockets and its connection with the userspace audit daemon. Fixing this properly had quite the cascading effect and what we are left with is this rather large and complicated patch. My initial goal was to try and decompose this patch into multiple smaller patches, but the way these changes are intertwined makes it difficult to split these changes into meaningful pieces that don't break or somehow make things worse for the intermediate states. The patch makes a number of changes, but the most significant are highlighted below: * The auditd tracking variables, e.g. audit_sock, are now gone and replaced by a RCU/spin_lock protected variable auditd_conn which is a structure containing all of the auditd tracking information. * We no longer track the auditd sock directly, instead we track it via the network namespace in which it resides and we use the audit socket associated with that namespace. In spirit, this is what the code was trying to do prior to this patch (at least I think that is what the original authors intended), but it was done rather poorly and added a layer of obfuscation that only masked the underlying problems. * Big backlog queue cleanup, again. In v4.10 we made some pretty big changes to how the audit backlog queues work, here we haven't changed the queue design so much as cleaned up the implementation. Brought about by the locking changes, we've simplified kauditd_thread() quite a bit by consolidating the queue handling into a new helper function, kauditd_send_queue(), which allows us to eliminate a lot of very similar code and makes the looping logic in kauditd_thread() clearer. * All netlink messages sent to auditd are now sent via auditd_send_unicast_skb(). Other than just making sense, this makes the lock handling easier. * Change the audit_log_start() sleep behavior so that we never sleep on auditd events (unchanged) or if the caller is holding the audit_cmd_mutex (changed). Previously we didn't sleep if the caller was auditd or if the message type fell between a certain range; the type check was a poor effort of doing what the cmd_mutex check now does. Richard Guy Briggs originally proposed not sleeping the cmd_mutex owner several years ago but his patch wasn't acceptable at the time. At least the idea lives on here. * A problem with the lost record counter has been resolved. Steve Grubb and I both happened to notice this problem and according to some quick testing by Steve, this problem goes back quite some time. It's largely a harmless problem, although it may have left some careful sysadmins quite puzzled. Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
Paul Moore <paul@paul-moore.com> Signed-off-by:
-
Nicholas Piggin authored
commit 6d98ce0b upstream. We concluded there may be a window where the idle wakeup code could get to pnv_wakeup_tb_loss() (which clobbers non-volatile GPRs), but the hardware may set SRR1[46:47] to 01b (no state loss) which would result in the wakeup code failing to restore non-volatile GPRs. I was not able to trigger this condition with trivial tests on real hardware or simulator, but the ISA (at least 2.07) seems to allow for it, and Gautham says that it can happen if there is an exception pending when the sleep/winkle instruction is executed. Fixes: 17065671 ("powerpc/kvm: make hypervisor state restore a function") Signed-off-by:
Nicholas Piggin <npiggin@gmail.com> Acked-by:
Gautham R. Shenoy <ego@linux.vnet.ibm.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Theodore Ts'o authored
commit dac7a4b4 upstream. We must lock the xattr block before calculating or verifying the checksum in order to avoid spurious checksum failures. https://bugzilla.kernel.org/show_bug.cgi?id=193661Reported-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Eric Biggers authored
commit b9cf625d upstream. If ext4_convert_inline_data() was called on a directory with inline data, the filesystem was left in an inconsistent state (as considered by e2fsck) because the file size was not increased to cover the new block. This happened because the inode was not marked dirty after i_disksize was updated. Fix this by marking the inode dirty at the end of ext4_finish_convert_inline_dir(). This bug was probably not noticed before because most users mark the inode dirty afterwards for other reasons. But if userspace executed FS_IOC_SET_ENCRYPTION_POLICY with invalid parameters, as exercised by 'kvm-xfstests -c adv generic/396', then the inode was never marked dirty after updating i_disksize. Fixes: 3c47d541Signed-off-by:
-
Sudip Mukherjee authored
commit 9a69645d upstream. Usually every parallel port will have a single pardev registered with it. But ppdev driver is an exception. This userspace parallel port driver allows to create multiple parrallel port devices for a single parallel port. And as a result we were having a big warning like: "sysfs: cannot create duplicate filename '/devices/parport0/ppdev0.0'". And with that many parallel port printers stopped working. We have been using the minor number as the id field while registering a parralel port device with a parralel port. But when there are multiple parrallel port device for one single parallel port, they all tried to register with the same name like 'pardev0.0' and everything started failing. Use an incremented index as the id instead of the minor number. Fixes: 8b7d3a9d ("ppdev: use new parport device model") Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1414656 Bugzilla: https://bugs.archlinux.org/task/52322Tested-by:
James Feeney <james@nurealm.net> Signed-off-by:
Sudip Mukherjee <sudip.mukherjee@codethink.co.uk> Signed-off-by:
-
Sudip Mukherjee authored
commit 03270c6a upstream. Usually every parallel port will have a single pardev registered with it. But ppdev driver is an exception. This userspace parallel port driver allows to create multiple parrallel port devices for a single parallel port. And as a result we were having a nice warning like: "sysctl table check failed: /dev/parport/parport0/devices/ppdev0/timeslice Sysctl already exists" Use the same logic as used in parport_register_device() and register the proc files only once for each parallel port. Fixes: 6fa45a22 ("parport: add device-model to parport subsystem") Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1414656 Bugzilla: https://bugs.archlinux.org/task/52322Tested-by:
-
Alexander Usyskin authored
commit c6240cac upstream. The driver still struggles with firmwares that do not replay to the OS version request. It is safe not waiting for the replay. First, the driver doesn't do anything with the replay second the connection is closed immediately, hence the packet will be just safely discarded in case it is received and last the driver won't get stuck if the firmware won't reply. Signed-off-by:
Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by:
Tomas Winkler <tomas.winkler@intel.com> Signed-off-by:
-
Tomas Winkler authored
commit a733ded5 upstream. This patch fixes 'mei: synchronize irq before initiating a reset' The patch had introduced a deadlock between irq thread and mei_reset() as they are both holding the same device lock. ---> device_lock: mei_reset() <---- interrupt thread device_lock ---> synchornize_irq() wait on interrupt thread == (dead lock) The fix is to call synchronize_irq prior to call locked mei_reset function. Fixes: f302bb0de6ac (mei: synchronize irq before initiating a reset) Signed-off-by:
-
Dmitry Torokhov authored
commit 3ff861f5 upstream. Even if bus is not hot-pluggable, devices can be unbound from the driver via sysfs, so we should not be using __exit annotations on remove() methods. The only exception is drivers registered with platform_driver_probe() which specifically disables sysfs bind/unbind attributes. Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Song Hongyan authored
iio: hid-sensor-trigger: Change get poll value function order to avoid sensor properties losing after resume from S3 commit 3bec2474 upstream. In function _hid_sensor_power_state(), when hid_sensor_read_poll_value() is called, sensor's all properties will be updated by the value from sensor hardware/firmware. In some implementation, sensor hardware/firmware will do a power cycle during S3. In this case, after resume, once hid_sensor_read_poll_value() is called, sensor's all properties which are kept by driver during S3 will be changed to default value. But instead, if a set feature function is called first, sensor hardware/firmware will be recovered to the last status. So change the sensor_hub_set_feature() calling order to behind of set feature function to avoid sensor properties lose. Signed-off-by:
Song Hongyan <hongyan.song@intel.com> Acked-by:
Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by:
-
Lars-Peter Clausen authored
commit c42f8218 upstream. Use the IS_ENABLED() helper macro to ensure that the configfs group is initialized either when configfs is built-in or when configfs is built as a module. Otherwise software device creation will result in undefined behaviour when configfs is built as a module since the configfs group for the device not properly initialized. Similar to commit b2f0c096 ("iio: sw-trigger: Fix config group initialization"). Fixes: 0f3a8c3f ("iio: Add support for creating IIO devices via configfs") Reported-by:
Miguel Robles <miguel.robles@farole.net> Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Acked-by:
Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by:
-
Michael Engl authored
commit e83bb3e6 upstream. The tiadc_irq_h(int irq, void *private) function is handling FIFO overruns by clearing flags, disabling and enabling the ADC to recover. If the ADC is running in continuous mode a FIFO overrun happens regularly. If the disabling of the ADC happens concurrently with a new conversion. It might happen that the enabling of the ADC is ignored by the hardware. This stops the ADC permanently. No more interrupts are triggered. According to the AM335x Reference Manual (SPRUH73H October 2011 - Revised April 2013 - Chapter 12.4 and 12.5) it is necessary to check the ADC FSM bits in REG_ADCFSM before enabling the ADC again. Because the disabling of the ADC is done right after the current conversion has been finished. To trigger this bug it is necessary to run the ADC in continuous mode. The ADC values of all channels need to be read in an endless loop. The bug appears within the first 6 hours (~5.4 million handled FIFO overruns). The user space application will hang on reading new values from the character device. Fixes: ca9a5638 ("iio: ti_am335x_adc: Add continuous sampling support") Signed-off-by:
Michael Engl <michael.engl@wjw-solutions.com> Signed-off-by:
-
Guenter Roeck authored
commit 773dc118 upstream. HS400-ES devices fail to initialize with the following error messages. mmc1: power class selection to bus width 8 ddr 0 failed mmc1: error -110 whilst initialising MMC card This was seen on Samsung Chromebook Plus. Code analysis points to commit 3d4ef329 ("mmc: core: fix multi-bit bus width without high-speed mode"), which attempts to set the bus width for all but HS200 devices unconditionally. However, for HS400-ES, the bus width is already selected. Cc: Anssi Hannula <anssi.hannula@bitwise.fi> Cc: Douglas Anderson <dianders@chromium.org> Cc: Brian Norris <briannorris@chromium.org> Fixes: 3d4ef329 ("mmc: core: fix multi-bit bus width ...") Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Reviewed-by:
Douglas Anderson <dianders@chromium.org> Reviewed-by:
Shawn Lin <shawn.lin@rock-chip.com> Tested-by:
Heiko Stuebner <heiko@sntech.de> Signed-off-by:
-
Johannes Berg authored
commit ea90e0dc upstream. Sowmini pointed out Dmitry's RTNL deadlock report to me, and it turns out to be perfectly accurate - there are various error paths that miss unlock of the RTNL. To fix those, change the locking a bit to not be conditional in all those nl80211_prepare_*_dump() functions, but make those require the RTNL to start with, and fix the buggy error paths. This also let me use sparse (by appropriately overriding the rtnl_lock/rtnl_unlock functions) to validate the changes. Reported-by:
Sowmini Varadhan <sowmini.varadhan@oracle.com> Reported-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Johan Hovold authored
commit 181302dc upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Fixes: 53f3a9e2 ("mmc: USB SD Host Controller (USHC) driver") Cc: David Vrabel <david.vrabel@csr.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Johan Hovold authored
commit daf229b1 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Note that the dereference happens in the start callback which is called during probe. Fixes: de520b8b ("uwb: add HWA radio controller driver") Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Cc: David Vrabel <david.vrabel@csr.com> Signed-off-by:
-
Johan Hovold authored
commit 4ce36271 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Note that the dereference happens in the cmd and wait_init_done callbacks which are called during probe. Fixes: 1ba47da5 ("uwb: add the i1480 DFU driver") Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Cc: David Vrabel <david.vrabel@csr.com> Signed-off-by:
-
Johan Hovold authored
commit 2e47c535 upstream. Make sure to initialise the return value to avoid having allocation failures going unnoticed when allocating interrupt-endpoint resources. This prevents use-after-free or worse when the device is later unbound. Fixes: dbf3e7f6 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation.") Cc: Dave Penkler <dpenkler@gmail.com> Signed-off-by:
-
Johan Hovold authored
commit 687e0687 upstream. USBTMC devices are required to have a bulk-in and a bulk-out endpoint, but the driver failed to verify this, something which could lead to the endpoint addresses being taken from uninitialised memory. Make sure to zero all private data as part of allocation, and add the missing endpoint sanity check. Note that this also addresses a more recently introduced issue, where the interrupt-in-presence flag would also be uninitialised whenever the optional interrupt-in endpoint is not present. This in turn could lead to an interrupt urb being allocated, initialised and submitted based on uninitialised values. Fixes: dbf3e7f6 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation.") Fixes: 5b775f67 ("USB: add USB test and measurement class driver") Signed-off-by:
-
Guenter Roeck authored
commit 7b2db29f upstream. If usb_get_bos_descriptor() returns an error, usb->bos will be NULL. Nevertheless, it is dereferenced unconditionally in hub_set_initial_usb2_lpm_policy() if usb2_hw_lpm_capable is set. This results in a crash. usb 5-1: unable to get BOS descriptor ... Unable to handle kernel NULL pointer dereference at virtual address 00000008 pgd = ffffffc00165f000 [00000008] *pgd=000000000174f003, *pud=000000000174f003, *pmd=0000000001750003, *pte=00e8000001751713 Internal error: Oops: 96000005 [#1] PREEMPT SMP Modules linked in: uinput uvcvideo videobuf2_vmalloc cmac [ ... ] CPU: 5 PID: 3353 Comm: kworker/5:3 Tainted: G B 4.4.52 #480 Hardware name: Google Kevin (DT) Workqueue: events driver_set_config_work task: ffffffc0c3690000 ti: ffffffc0ae9a8000 task.ti: ffffffc0ae9a8000 PC is at hub_port_init+0xc3c/0xd10 LR is at hub_port_init+0xc3c/0xd10 ... Call trace: [<ffffffc0007fbbfc>] hub_port_init+0xc3c/0xd10 [<ffffffc0007fbe2c>] usb_reset_and_verify_device+0x15c/0x82c [<ffffffc0007fc5e0>] usb_reset_device+0xe4/0x298 [<ffffffbffc0e3fcc>] rtl8152_probe+0x84/0x9b0 [r8152] [<ffffffc00080ca8c>] usb_probe_interface+0x244/0x2f8 [<ffffffc000774a24>] driver_probe_device+0x180/0x3b4 [<ffffffc000774e48>] __device_attach_driver+0xb4/0xe0 [<ffffffc000772168>] bus_for_each_drv+0xb4/0xe4 [<ffffffc0007747ec>] __device_attach+0xd0/0x158 [<ffffffc000775080>] device_initial_probe+0x24/0x30 [<ffffffc0007739d4>] bus_probe_device+0x50/0xe4 [<ffffffc000770bd0>] device_add+0x414/0x738 [<ffffffc000809fe8>] usb_set_configuration+0x89c/0x914 [<ffffffc00080a120>] driver_set_config_work+0xc0/0xf0 [<ffffffc000249bb8>] process_one_work+0x390/0x6b8 [<ffffffc00024abcc>] worker_thread+0x480/0x610 [<ffffffc000251a80>] kthread+0x164/0x178 [<ffffffc0002045d0>] ret_from_fork+0x10/0x40 Since we don't know anything about LPM capabilities without BOS descriptor, don't attempt to enable LPM if it is not available. Fixes: 890dae88 ("xhci: Enable LPM support only for hardwired ...") Cc: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Bin Liu authored
commit 0090114d upstream. The CPPI 4.1 driver polls register to workaround the premature TX interrupt issue, but it causes audio playback underrun when triggered in Isoch transfers. Isoch doesn't do back-to-back transfers, the TX should be done by the time the next transfer is scheduled. So skip this polling workaround for Isoch transfer. Fixes: a655f481 ("usb: musb: musb_cppi41: handle pre-mature TX complete interrupt") Reported-by:
Alexandre Bailon <abailon@baylibre.com> Acked-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Tested-by:
Bin Liu <b-liu@ti.com> Signed-off-by:
-
Johan Hovold authored
commit 03ace948 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer or accessing memory beyond the endpoint array should a malicious device lack the expected endpoints. This specifically fixes the NULL-pointer dereference when probing HWA HC devices. Fixes: df365423 ("wusb: add the Wire Adapter (WA) core") Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Cc: David Vrabel <david.vrabel@csr.com> Signed-off-by:
-
Johan Hovold authored
commit b0addd3f upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Johan Hovold authored
commit 1dc56c52 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should the probed device lack endpoints. Note that this driver does not bind to any devices by default. Fixes: ce21bfe6 ("USB: Add LVS Test device driver") Cc: Pratyush Anand <pratyush.anand@gmail.com> Signed-off-by:
-
Johan Hovold authored
commit f259ca3e upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer or accessing memory beyond the endpoint array should a malicious device lack the expected endpoints. Note that the endpoint access that causes the NULL-deref is currently only used for debugging purposes during probe so the oops only happens when dynamic debugging is enabled. This means the driver could be rewritten to continue to accept device with only two endpoints, should such devices exist. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Samuel Thibault authored
commit 3243367b upstream. Some USB 2.0 devices erroneously report millisecond values in bInterval. The generic config code manages to catch most of them, but in some cases it's not completely enough. The case at stake here is a USB 2.0 braille device, which wants to announce 10ms and thus sets bInterval to 10, but with the USB 2.0 computation that yields to 64ms. It happens that one can type fast enough to reach this interval and get the device buffers overflown, leading to problematic latencies. The generic config code does not catch this case because the 64ms is considered a sane enough value. This change thus adds a USB_QUIRK_LINEAR_FRAME_INTR_BINTERVAL quirk to mark devices which actually report milliseconds in bInterval, and marks Vario Ultra devices as needing it. Signed-off-by:
Samuel Thibault <samuel.thibault@ens-lyon.org> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
