This patch switches can_pernet_init() to the preferred style of using
the sizeof() operator in kzalloc().
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch joins all error message strings in af_can to be in single
lines, to ease searching for them.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch fixes the alignment of find_dev_rcv_lists() and canfd_rcv()
so that checkpatch doesn't complain anymore.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch balances the braces around else statements, so that
checkpatch doesn't complain anymore.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch converts all block comments to network subsystem style block
comments.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

While calculating bitrate for the data phase, the driver is using phase
segment 1 of the arbitration phase instead of the data phase.

Fixes: c223da68 ("can: xilinx_can: Add support for CANFD FD frames")
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Acked-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

can: xilinx_can: xcan_rx_fifo_get_next_frame(): fix FSR register FL and RI mask values for canfd 2.0

For CANFD 2.0 IP configuration existing driver is using incorrect mask
values for FSR register FL and RI fields.

Fixes: c223da68 ("can: xilinx_can: Add support for CANFD FD frames")
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Acked-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

commit c223da68 ("can: xilinx_can: Add support for CANFD FD frames")
is writing data to a wrong offset for FD frames.

This patch fixes this issue.

Fixes: c223da68 ("can: xilinx_can: Add support for CANFD FD frames")
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Shubhrajyoti Datta <Shubhrajyoti.datta@xilinx.com>
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

After commit c223da68 ("can: xilinx_can: Add support for CANFD FD
frames") the driver is updating the FSR IRI index multiple times (i.e in
xcanfd_rx() and xcan_rx_fifo_get_next_frame()), It should be updated
once per RX packet. This patch fixes this issue, also this patch removes
the unnecessary fsr register checks in xcanfd_rx() API.

Fixes: c223da68 ("can: xilinx_can: Add support for CANFD FD frames")
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Shubhrajyoti Datta <Shubhrajyoti.datta@xilinx.com>
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

When can clock is provided from the clock wizard, clock wizard driver
may not be available when can driver probes resulting to the error
message "Device clock not found error".

As this error message is not very userful to the end user, skip printing
it in the case of deferred probe.

Fixes: b1201e44 ("can: xilinx CAN controller support")
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Currently the xilinx_can xcan_chip_start() function, called from
.ndo_open() and via CAN_MODE_START (bus-off restart), waits for the SR
register to show the wanted operating state, with a 1 sec timeout.

However, that register bit will only be set once the HW has observed 11
consecutive recessive bits (BusIdle) on the bus.

If the bus will not see the 11 bits (e.g. it is stuck dominant), the
function will timeout and return an error. If this was done as part of a
scheduled restart from bus-off, the interface will stay in bus-off state
forever even if the bus recovers later.

According to M_CAN and FLEXCAN documentation they also wait for 11
consecutive recessive bits, but their drivers do not seem to wait for
that.

To make the behavior consistent, modify xilinx_can to also not wait for
the synchronization to complete.

The only way for users to know for sure that the bus has been joined
successfully is to see successfully received or transmitted frames. That
does not seem optimal, but it is consistent with other drivers and we
should have a properly working restart-ms with xilinx_can.

Tested on ZynqMP with Xilinx CAN-FD 1.0.

Fixes: b1201e44 ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Tested-by: Appana Durga Kedareswara Rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/can/ti_hecc.c: In function 'ti_hecc_mailbox_read':
drivers/net/can/ti_hecc.c:533:12: warning:
 variable 'mbx_mask' set but not used [-Wunused-but-set-variable]

It is never used so can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch adds two blank lines in ti_hecc_mailbox_read() to improve the
readability of the function.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch changes the multiple assignments of HECC_TX_MASK in
ti_hecc_start() into two single ones.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch fixes the print format strings in the driver.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch fixes long lines in the driver.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch fixes the indention in the driver.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch converts all block comments to network subsystem style block
comments.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Remove including <linux/version.h> that don't need it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

can: kvaser_pciefd: kvaser_pciefd_pwm_stop(): remove unnecessary code when setting pwm duty cycle to zero

To set the duty cycle to zero (i.e. pwm_stop), the trigger value shall
be equal to the top value.

This is achieved by reading the value of the top bit field from the pwm
register and then writing back this value to the trigger and top bit
fields.

Addresses-Coverity: ("Logically dead code")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Christer Beskow <chbe@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

When calling debugfs functions, there is no need to ever check the
return value.  The function can work or not, but the code logic should
never do something different based on this.

Cc: Richard Fontana <rfontana@redhat.com>
Cc: Steve Winslow <swinslow@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When calling debugfs functions, there is no need to ever check the
return value.  The function can work or not, but the code logic should
never do something different based on this.

Cc: Wei Liu <wei.liu@kernel.org>
Cc: Paul Durrant <paul.durrant@citrix.com>
Cc: xen-devel@lists.xenproject.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vivien Didelot says:

====================
net: dsa: mv88e6xxx: prepare Wait Bit operation

The Remote Management Interface has its own implementation of a Wait
Bit operation, which requires a bit number and a value to wait for.

In order to prepare the introduction of this implementation, rework the
code waiting for bits and masks in mv88e6xxx to match this signature.

This has the benefit to unify the implementation of wait routines while
removing obsolete wait and update functions and also reducing the code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The mv88e6xxx_smi_direct_wait routine is used to wait on indirect
registers access. It is of no exception and must delay between read
attempts, like other wait routines.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current mv88e6xxx_smi_direct_wait function is only used to check
the 16th bit of the (16-bit) SMI Command register. But the bit shift
operation is not enough if we eventually use this function to check
other bits, thus replace it with a mask.

Fixes: e7ba0fad ("net: dsa: mv88e6xxx: refine SMI support")
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we have proper Wait Bit and Wait Mask routines, remove the
unused mv88e6xxx_wait routine and its Global 1 and Global 2 variants.

The indirect tables such as the Device Mapping Table or Priority
Override Table make use of an Update bit to distinguish reading (0)
from writing (1) operations. After a write operation occurs, the bit
self clears right away so there's no need to wait on it. Thus keep
things simple and remove the mv88e6xxx_update helper as well.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The AVB is not an indirect table using an Update bit, but a unit using
a Busy bit. This means that we must ensure that this bit is cleared
before setting it and wait until it gets cleared again after writing
an operation. Reflect that.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Many portions of the driver need to wait until a given bit is set
or cleared. Some busses even have a specific implementation for this
operation. In preparation for such variant, implement a generic Wait
Bit routine that can be used by the driver core functions.

This allows us to get rid of the custom implementations we may find
in the driver. Note that for the EEPROM bits, BUSY and RUNNING bits
are independent, thus it is more efficient to wait independently for
each bit instead of waiting for their mask.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current mv88e6xxx_wait routine is used to wait for a given mask
to be cleared to zero. However in some cases, the driver may have
to wait for a given mask to be of a certain non-zero value.

Thus provide a generic wait mask routine that will be used to implement
the current mv88e6xxx_wait function, and use it to wait for 88E6185
PPU states.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PPU state of 88E6185 can be either "Disabled at Reset" or
"Disabled after Initialization". Because we intentionally clear the
PPU Enabled bit before checking its state, it is safe to wait for the
MV88E6185_G1_STS_PPU_STATE_DISABLED state explicitly instead of waiting
for any state different than MV88E6185_G1_STS_PPU_STATE_POLLING.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rtl8169_free_rx_databuff is used in only one place, so let's inline it.
We can improve the loop because rtl8169_init_ring zero's RX_databuff
before calling rtl8169_rx_fill, and rtl8169_rx_fill fills
Rx_databuff starting from index 0.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: realtek: add support for integrated 2.5Gbps PHY in RTL8125

This series adds support for the integrated 2.5Gbps PHY in RTL8125.
First three patches add necessary functionality to phylib.

Changes in v2:
- added patch 1
- changed patch 4 to use a fake PHY ID that is injected by the
  network driver. This allows to use a dedicated PHY driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds support for the integrated 2.5Gbps PHY in Realtek RTL8125.
Advertisement of 2.5Gbps mode is done via a vendor-specific register.
Same applies to reading NBase-T link partner advertisement.
Unfortunately this 2.5Gbps PHY shares the PHY ID with the integrated
1Gbps PHY's in other Realtek network chips and so far no method is
known to differentiate them. As a workaround use a dedicated fake PHY ID
that is set by the network driver by intercepting the MDIO PHY ID read.

v2:
- Create dedicated PHY driver and use a fake PHY ID that is injected by
  the network driver. Suggested by Andrew Lunn.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add helper function phy_modify_paged_changed, behavios is the same
as for phy_modify_changed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The integrated PHY in 2.5Gbps chip RTL8125 is the first (known to me)
PHY that uses standard Clause 22 for all modes up to 1Gbps and adds
2.5Gbps control using vendor-specific registers. To use phylib for
the standard part little extensions are needed:
- Move most of genphy_config_aneg to a new function
  __genphy_config_aneg that takes a parameter whether restarting
  auto-negotiation is needed (depending on whether content of
  vendor-specific advertisement register changed).
- Don't clear phydev->lp_advertising in genphy_read_status so that
  we can set non-C22 mode flags before.

Basically both changes mimic the behavior of the equivalent Clause 45
functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Using linkmode_adv_to_mii_adv_t and linkmode_adv_to_mii_ctrl1000_t
allows to simplify the code. In addition avoiding the conversion to
the legacy u32 advertisement format allows to remove the warning.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Register couple of devlink params, one generic, one driver-specific.
Make the values available over debugfs.

Example:
$ echo "111" > /sys/bus/netdevsim/new_device
$ devlink dev param
netdevsim/netdevsim111:
  name max_macs type generic
    values:
      cmode driverinit value 32
  name test1 type driver-specific
    values:
      cmode driverinit value true
$ cat /sys/kernel/debug/netdevsim/netdevsim111/max_macs
32
$ cat /sys/kernel/debug/netdevsim/netdevsim111/test1
Y
$ devlink dev param set netdevsim/netdevsim111 name max_macs cmode driverinit value 16
$ devlink dev param set netdevsim/netdevsim111 name test1 cmode driverinit value false
$ devlink dev reload netdevsim/netdevsim111
$ cat /sys/kernel/debug/netdevsim/netdevsim111/max_macs
16
$ cat /sys/kernel/debug/netdevsim/netdevsim111/test1
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
drop_monitor: Capture dropped packets and metadata

So far drop monitor supported only one mode of operation in which a
summary of recent packet drops is periodically sent to user space as a
netlink event. The event only includes the drop location (program
counter) and number of drops in the last interval.

While this mode of operation allows one to understand if the system is
dropping packets, it is not sufficient if a more detailed analysis is
required. Both the packet itself and related metadata are missing.

This patchset extends drop monitor with another mode of operation where
the packet - potentially truncated - and metadata (e.g., drop location,
timestamp, netdev) are sent to user space as a netlink event. Thanks to
the extensible nature of netlink, more metadata can be added in the
future.

To avoid performing expensive operations in the context in which
kfree_skb() is called, the dropped skbs are cloned and queued on per-CPU
skb drop list. The list is then processed in process context (using a
workqueue), where the netlink messages are allocated, prepared and
finally sent to user space.

A follow-up patchset will integrate drop monitor with devlink and allow
the latter to call into drop monitor to report hardware drops. In the
future, XDP drops can be added as well, thereby making drop monitor the
go-to netlink channel for diagnosing all packet drops.

Example usage with patched dropwatch [1] can be found here [2]. Example
dissection of drop monitor netlink events with patched wireshark [3] can
be found here [4]. I will submit both changes upstream after the kernel
changes are accepted. Another change worth making is adding a dropmon
pseudo interface to libpcap, similar to the nflog interface [5]. This
will allow users to specifically listen on dropmon traffic instead of
capturing all netlink packets via the nlmon netdev.

Patches #1-#5 prepare the code towards the actual changes in later
patches.

Patch #6 adds another mode of operation to drop monitor in which the
dropped packet itself is notified to user space along with metadata.

Patch #7 allows users to truncate reported packets to a specific length,
in case only the headers are of interest. The original length of the
packet is added as metadata to the netlink notification.

Patch #8 allows user to query the current configuration of drop monitor
(e.g., alert mode, truncation length).

Patches #9-#10 allow users to tune the length of the per-CPU skb drop
list according to their needs.

Changes since v1 [6]:
* Add skb protocol as metadata. This allows user space to correctly
  dissect the packet instead of blindly assuming it is an Ethernet
  packet

Changes since RFC [7]:
* Limit the length of the per-CPU skb drop list and make it configurable
* Do not use the hysteresis timer in packet alert mode
* Introduce alert mode operations in a separate patch and only then
  introduce the new alert mode
* Use 'skb->skb_iif' instead of 'skb->dev' because the latter is inside
  a union with 'dev_scratch' and therefore not guaranteed to point to a
  valid netdev
* Return '-EBUSY' instead of '-EOPNOTSUPP' when trying to configure drop
  monitor while it is monitoring
* Did not change schedule_work() in favor of schedule_work_on() as I did
  not observe a change in number of tail drops

[1] https://github.com/idosch/dropwatch/tree/packet-mode
[2] https://gist.github.com/idosch/3d524b887e16bc11b4b19e25c23dcc23#file-gistfile1-txt
[3] https://github.com/idosch/wireshark/tree/drop-monitor-v2
[4] https://gist.github.com/idosch/3d524b887e16bc11b4b19e25c23dcc23#file-gistfile2-txt
[5] https://github.com/the-tcpdump-group/libpcap/blob/master/pcap-netfilter-linux.c
[6] https://patchwork.ozlabs.org/cover/1143443/
[7] https://patchwork.ozlabs.org/cover/1135226/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Previous patch made the length of the per-CPU skb drop list
configurable. Expose a counter that shows how many packets could not be
enqueued to this list.

This allows users determine the desired queue length.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>