Fix a typo in A37xx pin controllers documentation about uart2 pin group.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Some two functions were missing from the Gemini pin control
driver. Noticed when trying to use ethernet. Fix it up by
adding them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Instead of depends on GPIOLIB and having to run around in
Kconfig menus looking for why your device is not available,
simply select it from the pin control drivers that need it.

The Kconfig for GPIOLIB is improved, selectable and this
should "just work".

Cc: Phil Reid <preid@electromag.com.au>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

GPIO is expected to be disabled iff PIN_CONFIG_BIAS_HIGH_IMPEDANCE is
configured. Update is_enabled flag in config_set() so that it can
reflect GPIO status correctly. Also modify EN_CTL register based on
is_enabled flag in config_set() to configure the GPIO properly.
Signed-off-by: Fenglin Wu <fenglinw@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Variable mask and val are not used in the mcp_pinconf_set().
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds the compatible string for the mcp23018, which is the i2c variant
of the mcp23s18.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The mcp23s08 driver moved to pinctrl recently. It accepts the
bias-pull-up pinctrl property since then. This updates the binding
doc to reflect that.

Thanks to Sebastian Reichel for the working example.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The mcp23s08 driver was moved from gpio to pinctrl. This moves it's
devicetree binding doc as well. So driver and binding doc are in sync
again.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This allows PINCTRL to be selected manually to allow enabling of the
mcp23s08 i2c/spi gpio driver. Which is not platform specific.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

While removing the need to have pin_base defined in meson pinctrl
drivers, I forgot to remove the corresponding field from the
pinctrl_data structure.

Fixing this now.

Fixes: 70e5ecb1 ("pinctrl: meson: get rid of pin_base")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add TEST_N pinmux for channel 6 and 7 of the i2s output
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The structure sx150x_regmap_config is local to the source and does not
need to be in global scope, so make it static.

Cleans up sparse warning:
symbol 'sx150x_regmap_config' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The function ingenic_pinctrl_probe is local to the source and does
not need to be in global scope, so make it static.

Cleans up sparse warnings
symbol 'ingenic_pinctrl_probe' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge tag 'sh-pfc-for-v4.15-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel

pinctrl: sh-pfc: Updates for v4.15

  - Add SDHI and DRIF pin groups on R-Car H3 ES2.0,
  - Add USB3.0 host pin groups on R-Car H3 (ES1.x and ES2.0),
  - Add EthernetAVB and USB2.0 host pin groups on R-Car D3.

If the gmac-m1 optimization(bit10) is selected, the gpio function
of gmac pins is not valid. We may use the rmii mode for gmac interface,
the pins such as rx_d2, rx_d3, which the rgmii mode used, but rmii not
used could be taken as gpio function. So gmac_rxd0m1 selects the bit2,
and gmac_rxd0m3 select bit10 is more correct.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The offset of gpio0 and gpio1 bank drive strength is 0x8, not 0x4.
But the mux is 0x4, we couldn't use the IOMUX_WIDTH_4BIT flag, so
we give them actual offset.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

These request/free functions are just reimplementations of the
standard helpers in gpiolib. Delete them and replace with the
helpers.
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

These request/free functions are just reimplementations of the
standard helpers in gpiolib. Delete them and replace with the
helpers.

Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

These request/free functions are just reimplementations of the
standard helpers in gpiolib. Delete them and replace with the
helpers.
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

GPIOX_22 is declared as a gpio but the id is no present in the pin
table. This hole trigger an error while reading the pingroup debugfs entry

GPIOX_22 is no routed externally. For all we know, it could an internal
pin of SoC
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

On meson-gx platforms, TEST_N has been incorrectly declared in the EE
controller while it belongs to AO controller.

Move the pin to the appropriate controller
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pin_base was used with the manually set pin offset in meson pinctrl. This
is no longer the case, pin_base is 0 on every meson pinctrl controllers
and should go away.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Offset on meson pinctrl and gpios is something that was carried from the
vendor driver, where there is a weird link between the 2
controllers. Since these 2 controllers are independent, this offset adds
an unnecessary complexity.

This patch remove this manually set offset and rely on pinctrl to figure
out the gpio base offset
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch adds USB3.0 ch0 pinmux support to R8A7795 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

This patch adds USB3{0,1} (USB3.0 host) pinmux support to R8A7795 ES1.x
SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Fixed typo on comment for north_community.
Signed-off-by: Chris Gorman <chrisjohgorman@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The pinctrl_request_gpio() and pinctrl_free_gpio() break the nice
namespacing in the other cross-calls like pinctrl_gpio_foo().
Just rename them and all references so we have one namespace
with all cross-calls under pinctrl_gpio_*().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

ENOSYS is special and should only be used for incorrect syscall number.
It is not the case here. let's use ENOTSUPP instead.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Don't populate the read-only arrays prop2 and prop4 on the stack, instead
make them static const.  Makes the object code smaller by over 230 bytes:

Before:
   text	   data	    bss	    dec	    hex	filename
  28235	   5820	    192	  34247	   85c7	drivers/pinctrl/pinctrl-single.o

After:
   text	   data	    bss	    dec	    hex	filename
  27839	   5980	    192	  34011	   84db	drivers/pinctrl/pinctrl-single.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The functions amd_gpio_suspend and amd_gpio_resume are local to the
source and do not need to be in global scope, so make them static.

Cleans up sparse warnings:
symbol 'amd_gpio_suspend' was not declared. Should it be static?
symbol 'amd_gpio_resume' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

DRIF support for r8a7795 was initially added with commit 2d775831
("pinctrl: sh-pfc: r8a7795: Add DRIF support") and later dropped from
the new pfc-r8a7795.c while re-naming the initial pfc-r8a7795.c to
pfc-r8a7795-es1.c in commit b205914c ("pinctrl: sh-pfc: r8a7795:
Add support for R-Car H3 ES2.0"). As the DRIF doesn't differ, re-add
it here.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add SDHI0-3 support for R-Car H3 ES2.0 based on a patch from the Renesas
BSP. SDHI pin config is identical to H3 ES1.*.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Don't populate const arrays on the stack, instead make them
static.  Makes the object code smaller nearly 1000 bytes. Also
line break wide lines to avoid checkpatch warnings.

Before:
   text	   data	    bss	    dec	    hex	filename
  13112	   1996	      0	  15108	   3b04	pinctrl-uniphier-core.o

After:
   text	   data	    bss	    dec	    hex	filename
  11642	   2476	      0	  14118	   3726	pinctrl-uniphier-core.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull UBI updates from Richard Weinberger:
 "Minor improvements"

* tag 'upstream-4.14-rc1' of git://git.infradead.org/linux-ubifs:
  UBI: Fix two typos in comments
  ubi: fastmap: fix spelling mistake: "invalidiate" -> "invalidate"
  ubi: pr_err() strings should end with newlines
  ubi: pr_err() strings should end with newlines
  ubi: pr_err() strings should end with newlines

Pull UML updates from Richard Weinberger:

 - minor improvements

 - fixes for Debian's new gcc defaults (pie enabled by default)

 - fixes for XSTATE/XSAVE to make UML work again on modern systems

* 'for-linus-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: return negative in tuntap_open_tramp()
  um: remove a stray tab
  um: Use relative modversions with LD_SCRIPT_DYN
  um: link vmlinux with -no-pie
  um: Fix CONFIG_GCOV for modules.
  Fix minor typos and grammar in UML start_up help
  um: defconfig: Cleanup from old Kconfig options
  um: Fix FP register size for XSTATE/XSAVE