- 21 Mar, 2006 19 commits
-
-
Michael Krufky authored
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
-
Marcin Rudowski authored
This patch fixes default values for some picture controls: - brightness set to 50% by default (now is 0%) - hue set to 50% by default (now is 0%) - sets saturation to datasheet value - volume set to 0dB (now is -32dB) and some left small fixes: - twice offset adding - balance didn't follow datasheet (bits[0:5] = attenuation; bit[6] = channel to provide attenuation) Signed-off-by: Marcin Rudowski <mar_rud@poczta.onet.pl> Signed-off-by: Ian Pickworth <ian@pickworth.me.uk> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
-
Matheus Izvekov authored
This patch adds support for the IR remote control found in the card CX88_BOARD_PROLINK_PLAYTVPVR. Signed-off-by: Matheus Izvekov <mizvekov@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
-
Matheus Izvekov authored
This patch changes the gpio0 values for the card CX88_BOARD_PROLINK_PLAYTVPVR to the ones observed using RegSpy from the dscaler project. Signed-off-by: Matheus Izvekov <mizvekov@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
-
Rickard Osser authored
- Added support for AVerMedia A169 Dual Analog tuner card (dual saa7134 decoders - only 1 working right now) - Added autodetection for both parts of the card. It shows up like 2 cards, B1 and B - Enabled tuner B1, SVIDEO on B1 and composite1 through SVIDEO, FIXME: B is more or less dead at this point and I suspect the FM-radio is on the B part of the board Signed-off-by: Rickard Osser <ricky@osser.se> Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
-
Michael Krufky authored
- added tuner_lg_taln_pal_secam_ranges - renamed tuner 66 from TUNER_LG_NTSC_TALN_MINI to TUNER_LG_TALN - updated FlyTV mini Asus Digimatrix with new tuner Thanks-to: Rickard Osser <ricky@osser.se> Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
-
Michael Krufky authored
- matched indents on quotes within a printk Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
-
Michael Krufky authored
- added missing "count" element in Thomson FE6600 Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
-
Mauro Carvalho Chehab authored
Some chipsets have several problems when pci to pci transfers are activated on overlay mode. the option no_overlay allows disabling such feature of the driver, in favor of keeping the system stable. The default is to use pcipci_fail flag defined on drivers/pci/quirks.c. It also allows the user to override it by forcing disable overlay or forcing enable. Forcing enable may generate PCI transfer corruption, including disk mass corruption, so should be used with care. Added a text description to this option and make messages looks the same at both bttv and saa7134 drivers. Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
-
Andreas Oberritter authored
Used Lindent, manually changed some line breaks. Removed invalid email addresses, useless casts and useless initialization of return values. Signed-off-by: Andreas Oberritter <obi@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
-
Andreas Oberritter authored
Rename 'enum dmxdevype' to 'enum dmxdev_type' and use this enum instead of int for the member 'type' of struct dmxdev_filter. Signed-off-by: Andreas Oberritter <obi@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
-
Andreas Oberritter authored
The member dvbdev gets initialized once but is never used after that. Signed-off-by: Andreas Oberritter <obi@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
-
Andreas Oberritter authored
The PID value is already stored in struct dmx_sct_filter_params which is a member of struct dmxdev_filter. Acked-by: Johannes Stezenbach <js@linuxtv.org> Signed-off-by: Andreas Oberritter <obi@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
-
Marcin Rudowski authored
Old values generally works in A2 mono, but new ones allows: - detect and use Nicam stereo - mute in tv - use radio FM Signed-off-by: Marcin Rudowski <mar_rud@poczta.onet.pl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
-
Mauro Carvalho Chehab authored
Also Removed whitespaces introduced by previous tena patch Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
-
Ian Pickworth authored
There is an error in the cx88 code that causes this message in the syslog when balance is changed at full volume: Mar 4 18:35:08 ian2 kernel: cx88[0]: irq pci [0x1] vid* Mar 4 18:35:39 ian2 last message repeated 348 times Mar 4 18:36:01 ian2 last message repeated 564 times ... and so on The attached patch cures this problem. Signed-off-by: Ian Pickworth <ian@pickworth.me.uk> Signed-off-by: Marcin Rudowski <mar_rud@poczta.onet.pl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
-
Duncan Sands authored
The Coverity checker (previously Stanford checker) noticed that the value of nskips could be read even if it was never written. Signed-off-by: Duncan Sands <baldrick@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
-
Mauro Carvalho Chehab authored
Radio now works. Tuner now supports both PAL/D and STD/MN models Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
-
Linus Torvalds authored
Conflicts: Documentation/video4linux/CARDLIST.cx88 drivers/media/video/cx88/Kconfig drivers/media/video/em28xx/em28xx-video.c drivers/media/video/saa7134/saa7134-dvb.c Resolved as in the original merge by Mauro Carvalho Chehab
-
- 20 Mar, 2006 3 commits
-
-
Linus Torvalds authored
-
Andrea Arcangeli authored
This address is going to be obsolete, so I should update it.
-
git://ftp.linux-mips.org/pub/scm/upstream-linusLinus Torvalds authored
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: [MIPS] SB1: Check for -mno-sched-prolog if building corelis debug kernel. [MIPS] Sibyte: Fix race in sb1250_gettimeoffset(). [MIPS] Sibyte: Fix interrupt timer off by one bug. [MIPS] Sibyte: Fix M_SCD_TIMER_INIT and M_SCD_TIMER_CNT wrong field width. [MIPS] Protect more of timer_interrupt() by xtime_lock. [MIPS] Work around bad code generation for <asm/io.h>. [MIPS] Simple patch to power off DBAU1200 [MIPS] Fix DBAu1550 software power off. [MIPS] local_r4k_flush_cache_page fix [MIPS] SB1: Fix interrupt disable hazard. [MIPS] Get rid of the IP22-specific code in arclib. Update MAINTAINERS entry for MIPS.
-
- 19 Mar, 2006 2 commits
-
-
Michael Chan authored
The 40-bit DMA workaround recently implemented for 5714, 5715, and 5780 needs to be expanded because there may be other tg3 devices behind the EPB Express to PCIX bridge in the 5780 class device. For example, some 4-port card or mother board designs have 5704 behind the 5714. All devices behind the EPB require the 40-bit DMA workaround. Thanks to Chris Elmquist again for reporting the problem and testing the patch. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ralf Baechle DL5RB authored
If the AX.25 dialect chosen by the sysadmin is set to DAMA master / 3 (or DAMA slave / 2, if CONFIG_AX25_DAMA_SLAVE=n) ax25_kick() will fall through the switch statement without calling ax25_send_iframe() or any other function that would eventually free skbn thus leaking the packet. Fix by restricting the sysctl inferface to allow only actually supported AX.25 dialects. The system administration mistake needed for this to happen is rather unlikely, so this is an uncritical hole. Coverity #651. Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 18 Mar, 2006 16 commits
-
-
Michael Krufky authored
VIDEO_CX88_ALSA should not be between VIDEO_CX88_DVB and VIDEO_CX88_DVB_ALL_FRONTENDS When cx88-alsa was added to cx88/Kconfig, it was added in between VIDEO_CX88_DVB and VIDEO_CX88_DVB_ALL_FRONTENDS. This caused undesireable effects to the appearance of the menu options in menuconfig. This fix reorders cx88-alsa and cx88-dvb in Kconfig, to match saa7134, and restore the correct menuconfig appearance. Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Markus Rechberger authored
Fixed em28xx based system lockup, device needs to be initialized before starting the isoc transfer otherwise the system will completly lock up. Signed-off-by: Markus Rechberger <mrechberger@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Oleg Nesterov authored
sys_unshare() does mmput(new_mm). This is not enough if we have mm->core_waiters. This patch is a temporary fix for soon to be released 2.6.16. Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru> [ Checked with Uli: "I'm not planning to use unshare(CLONE_VM). It's not needed for any functionality planned so far. What we (as in Red Hat) need unshare() for now is the filesystem side." ] Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Ralf Baechle authored
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Ralf Baechle authored
From Dave Johnson <djohnson+linuxmips@sw.starentnetworks.com>: sb1250_gettimeoffset() simply reads the current cpu 0 timer remaining value, however once this counter reaches 0 and the interrupt is raised, it immediately resets and begins to count down again. If sb1250_gettimeoffset() is called on cpu 1 via do_gettimeofday() after the timer has reset but prior to cpu 0 processing the interrupt and taking write_seqlock() in timer_interrupt() it will return a full value (or close to it) causing time to jump backwards 1ms. Once cpu 0 handles the interrupt and timer_interrupt() gets far enough along it will jump forward 1ms. Fix this problem by implementing mips_hpt_*() on sb1250 using a spare timer unrelated to the existing periodic interrupt timers. It runs at 1Mhz with a full 23bit counter. This eliminated the custom do_gettimeoffset() for sb1250 and allowed use of the generic fixed_rate_gettimeoffset() using mips_hpt_*() and timerhi/timerlo. Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Ralf Baechle authored
From Dave Johnson <djohnson+linuxmips@sw.starentnetworks.com>: The timers need to be loaded with 1 less than the desired interval not the interval itself. Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Ralf Baechle authored
From Dave Johnson <djohnson+linuxmips@sw.starentnetworks.com>: Field width should be 23 bits not 20 bits. Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Ralf Baechle authored
From Dave Johnson <djohnson+linuxmips@sw.starentnetworks.com>: * do_timer() expects the arch-specific handler to take the lock as it modifies jiffies[_64] and xtime. * writing timerhi/lo in timer_interrupt() will mess up fixed_rate_gettimeoffset() which reads timerhi/lo. Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Ralf Baechle authored
If a call to set_io_port_base() was being followed by usage of mips_io_port_base in the same function gcc was possibly using the old value due to some clever abuse of const. Adding a barrier will keep the optimization and result in correct code with latest gcc. Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Matej Kupljen authored
Signed-off-by: Matej Kupljen <matej.kupljen@ultra.si> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Sergei Shtylylov authored
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Atsushi Nemoto authored
If dcache_size != icache_size or dcache_size != scache_size, or set-associative cache, icache/scache does not flushed properly. Make blast_?cache_page_indexed() masks its index value correctly. Also, use physical address for physically indexed pcache/scache. Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Ralf Baechle authored
The SB1 core has a three cycle interrupt disable hazard but we were wrongly treating it as fully interlocked. Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Ralf Baechle authored
This breaks the kernel build if sgiwd93 was configured as a module. Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Ralf Baechle authored
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Alexey Kuznetsov authored
It is broken, the condition is checked out of socket lock. It is wonderful the bug survived for so long time. [ This fixes bugzilla #6233: race condition in tcp_sendmsg when connection became established ] Signed-off-by: David S. Miller <davem@davemloft.net>
-