- 27 May, 2019 9 commits
-
-
Heiner Kallweit authored
Certain parts of the PHY initialization are the same for sub versions 1 and 2 of RTL8168d. So let's factor this out to simplify the code. Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Heiner Kallweit says: ==================== r8169: small improvements Series with small improvements. ==================== Signed-off-by: -
Heiner Kallweit authored
Use the appropriate enum type for member mac_version. And don't assign a fixed value to RTL_GIGA_MAC_NONE, there's no benefit in it. Signed-off-by:
-
Heiner Kallweit authored
Remove not needed return statement. Signed-off-by:
-
Heiner Kallweit authored
rtl_hw_init_8168ep() can be removed, this simplifies the code. Signed-off-by:
-
YueHaibing authored
Fix sparse warning: drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:6216:14: warning: symbol 't4_get_tp_e2c_map' was not declared. Should it be static? Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
David Ahern authored
I was really surprised that the IPv6 mtu exception followed by redirect test was passing as nothing about the code suggests it should. The problem is actually with the logic in the test script. Fix the test cases as follows: 1. add debug function to dump the initial and redirect gateway addresses for ipv6. This is shown only in verbose mode. It helps verify the output of 'route get'. 2. fix the check_exception logic for the reset case to make sure that for IPv4 neither mtu nor redirect appears in the 'route get' output. For IPv6, make sure mtu is not present and the gateway is the initial R1 lladdr. 3. fix the reset logic by using a function to delete the routes added by initial_route_*. This format works better for the nexthop version of the tests. While improving the test cases, go ahead and ensure that forwarding is disabled since IPv6 redirect requires it. Also, runs with kernel debugging enabled sometimes show a failure with one of the ipv4 tests, so spread the pings over longer time interval. The end result is that 2 tests now show failures: TEST: IPv6: mtu exception plus redirect [FAIL] and the VRF version. This is a bug in the IPv6 logic that will need to be fixed separately. Redirect followed by MTU works because __ip6_rt_update_pmtu hits the 'if (!rt6_cache_allowed_for_pmtu(rt6))' path and updates the mtu on the exception rt6_info. MTU followed by redirect does not have this logic. rt6_do_redirect creates a new exception and then rt6_insert_exception removes the old one which has the MTU exception. Fixes: ec810535 ("selftests: Add redirect tests") Signed-off-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
Colin Ian King authored
The pointer n is being assigned a value however this value is never read in the code block and the end of the code block continues to the next loop iteration. Clean up the code by removing the redundant assignment. Fixes: 1bff1a0c ("ipv4: Add function to send route updates") Addresses-Coverity: ("Unused value") Signed-off-by:
Colin Ian King <colin.king@canonical.com> Reviewed-by:
-
Heiner Kallweit authored
PHY drivers don't have to and shouldn't fiddle with phylib internals. Most of the code in bcm87xx_config_init() can be removed because phylib takes care. In addition I replaced usage of PHY_10GBIT_FEC_FEATURES with an implementation of the get_features callback. PHY_10GBIT_FEC_FEATURES is used by this driver only and it's questionable whether there will be any other PHY supporting this mode only. Having said that in one of the next kernel versions we may decide to remove it. Signed-off-by:
-
- 26 May, 2019 31 commits
-
-
David S. Miller authored
Eric Dumazet says: ==================== inet: frags: avoid possible races at netns dismantle This patch series fixes a race happening on netns dismantle with frag queues. While rhashtable_free_and_destroy() is running, concurrent timers might run inet_frag_kill() and attempt rhashtable_remove_fast() calls. This is not allowed by rhashtable logic. Since I do not want to add expensive synchronize_rcu() calls in the netns dismantle path, I had to no longer inline netns_frags structures, but dynamically allocate them. The ten first patches make this preparation, so that the last patch clearly shows the fix. As this patch series is not exactly trivial, I chose to target 5.3. We will backport it once soaked a bit. ==================== Signed-off-by: -
Eric Dumazet authored
syszbot found an interesting use-after-free [1] happening while IPv4 fragment rhashtable was destroyed at netns dismantle. While no insertions can possibly happen at the time a dismantling netns is destroying this rhashtable, timers can still fire and attempt to remove elements from this rhashtable. This is forbidden, since rhashtable_free_and_destroy() has no synchronization against concurrent inserts and deletes. Add a new fqdir->dead flag so that timers do not attempt a rhashtable_remove_fast() operation. We also have to respect an RCU grace period before starting the rhashtable_free_and_destroy() from process context, thus we use rcu_work infrastructure. This is a refinement of a prior rough attempt to fix this bug : https://marc.info/?l=linux-netdev&m=153845936820900&w=2 Since the rhashtable cleanup is now deferred to a work queue, netns dismantles should be slightly faster. [1] BUG: KASAN: use-after-free in __read_once_size include/linux/compiler.h:194 [inline] BUG: KASAN: use-after-free in rhashtable_last_table+0x162/0x180 lib/rhashtable.c:212 Read of size 8 at addr ffff8880a6497b70 by task kworker/0:0/5 CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.2.0-rc1+ #2 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Workqueue: events rht_deferred_worker Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x172/0x1f0 lib/dump_stack.c:113 print_address_description.cold+0x7c/0x20d mm/kasan/report.c:188 __kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317 kasan_report+0x12/0x20 mm/kasan/common.c:614 __asan_report_load8_noabort+0x14/0x20 mm/kasan/generic_report.c:132 __read_once_size include/linux/compiler.h:194 [inline] rhashtable_last_table+0x162/0x180 lib/rhashtable.c:212 rht_deferred_worker+0x111/0x2030 lib/rhashtable.c:411 process_one_work+0x989/0x1790 kernel/workqueue.c:2269 worker_thread+0x98/0xe40 kernel/workqueue.c:2415 kthread+0x354/0x420 kernel/kthread.c:255 ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352 Allocated by task 32687: save_stack+0x23/0x90 mm/kasan/common.c:71 set_track mm/kasan/common.c:79 [inline] __kasan_kmalloc mm/kasan/common.c:489 [inline] __kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:462 kasan_kmalloc+0x9/0x10 mm/kasan/common.c:503 __do_kmalloc_node mm/slab.c:3620 [inline] __kmalloc_node+0x4e/0x70 mm/slab.c:3627 kmalloc_node include/linux/slab.h:590 [inline] kvmalloc_node+0x68/0x100 mm/util.c:431 kvmalloc include/linux/mm.h:637 [inline] kvzalloc include/linux/mm.h:645 [inline] bucket_table_alloc+0x90/0x480 lib/rhashtable.c:178 rhashtable_init+0x3f4/0x7b0 lib/rhashtable.c:1057 inet_frags_init_net include/net/inet_frag.h:109 [inline] ipv4_frags_init_net+0x182/0x410 net/ipv4/ip_fragment.c:683 ops_init+0xb3/0x410 net/core/net_namespace.c:130 setup_net+0x2d3/0x740 net/core/net_namespace.c:316 copy_net_ns+0x1df/0x340 net/core/net_namespace.c:439 create_new_namespaces+0x400/0x7b0 kernel/nsproxy.c:107 unshare_nsproxy_namespaces+0xc2/0x200 kernel/nsproxy.c:206 ksys_unshare+0x440/0x980 kernel/fork.c:2692 __do_sys_unshare kernel/fork.c:2760 [inline] __se_sys_unshare kernel/fork.c:2758 [inline] __x64_sys_unshare+0x31/0x40 kernel/fork.c:2758 do_syscall_64+0xfd/0x680 arch/x86/entry/common.c:301 entry_SYSCALL_64_after_hwframe+0x49/0xbe Freed by task 7: save_stack+0x23/0x90 mm/kasan/common.c:71 set_track mm/kasan/common.c:79 [inline] __kasan_slab_free+0x102/0x150 mm/kasan/common.c:451 kasan_slab_free+0xe/0x10 mm/kasan/common.c:459 __cache_free mm/slab.c:3432 [inline] kfree+0xcf/0x220 mm/slab.c:3755 kvfree+0x61/0x70 mm/util.c:460 bucket_table_free+0x69/0x150 lib/rhashtable.c:108 rhashtable_free_and_destroy+0x165/0x8b0 lib/rhashtable.c:1155 inet_frags_exit_net+0x3d/0x50 net/ipv4/inet_fragment.c:152 ipv4_frags_exit_net+0x73/0x90 net/ipv4/ip_fragment.c:695 ops_exit_list.isra.0+0xaa/0x150 net/core/net_namespace.c:154 cleanup_net+0x3fb/0x960 net/core/net_namespace.c:553 process_one_work+0x989/0x1790 kernel/workqueue.c:2269 worker_thread+0x98/0xe40 kernel/workqueue.c:2415 kthread+0x354/0x420 kernel/kthread.c:255 ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352 The buggy address belongs to the object at ffff8880a6497b40 which belongs to the cache kmalloc-1k of size 1024 The buggy address is located 48 bytes inside of 1024-byte region [ffff8880a6497b40, ffff8880a6497f40) The buggy address belongs to the page: page:ffffea0002992580 refcount:1 mapcount:0 mapping:ffff8880aa400ac0 index:0xffff8880a64964c0 compound_mapcount: 0 flags: 0x1fffc0000010200(slab|head) raw: 01fffc0000010200 ffffea0002916e88 ffffea000218fe08 ffff8880aa400ac0 raw: ffff8880a64964c0 ffff8880a6496040 0000000100000005 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff8880a6497a00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8880a6497a80: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc >ffff8880a6497b00: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb ^ ffff8880a6497b80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8880a6497c00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb Fixes: 648700f7 ("inet: frags: use rhashtables for reassembly units") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
-
Eric Dumazet authored
Following patch will add rcu grace period before fqdir rhashtable destruction, so we need to dynamically allocate fqdir structures to not force expensive synchronize_rcu() calls in netns dismantle path. Signed-off-by:
-
Eric Dumazet authored
fqdir will soon be dynamically allocated. We need to reach the struct net pointer from fqdir, so add it, and replace the various container_of() constructs by direct access to the new field. Signed-off-by:
-
Eric Dumazet authored
And pass an extra parameter, since we will soon dynamically allocate fqdir structures. Signed-off-by:
-
Eric Dumazet authored
(struct net *)->ieee802154_lowpan.fqdir will soon be a pointer, so make sure lowpan_frags_ns_ctl_table[] does not reference init_net. lowpan_frags_ns_sysctl_register() can perform the needed initialization for all netns. Signed-off-by:
-
Eric Dumazet authored
(struct net *)->nf_frag.fqdir will soon be a pointer, so make sure nf_ct_frag6_sysctl_table[] does not reference init_net. nf_ct_frag6_sysctl_register() can perform the needed initialization for all netns. Signed-off-by:
-
Eric Dumazet authored
(struct net *)->ipv6.fqdir will soon be a pointer, so make sure ip6_frags_ns_ctl_table[] does not reference init_net. ip6_frags_ns_ctl_register() can perform the needed initialization for all netns. Signed-off-by:
-
Eric Dumazet authored
(struct net *)->ipv4.fqdir will soon be a pointer, so make sure ip4_frags_ns_ctl_table[] does not reference init_net. ip4_frags_ns_ctl_register() can perform the needed initialization for all netns. Signed-off-by:
-
Eric Dumazet authored
Rename the @frags fields from structs netns_ipv4, netns_ipv6, netns_nf_frag and netns_ieee802154_lowpan to @fqdir Signed-off-by:
-
Eric Dumazet authored
Signed-off-by:
-
Eric Dumazet authored
1) struct netns_frags is renamed to struct fqdir This structure is really holding many frag queues in a hash table. 2) (struct inet_frag_queue)->net field is renamed to fqdir since net is generally associated to a 'struct net' pointer in networking stack. Signed-off-by:
-
Marek Vasut authored
Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special BroadRReach 100BaseT1 PHYs used in automotive. Signed-off-by:
Marek Vasut <marex@denx.de> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: Jean Delvare <jdelvare@suse.com> Cc: linux-hwmon@vger.kernel.org Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
David S. Miller authored
Huazhong Tan says: ==================== net: hns3: add aRFS feature and fix FEC bugs for HNS3 driver This patchset adds some new features support and fixes some bugs: [Patch 1/4 - 3/4] adds support for aRFS [Patch 4/4] fix FEC configuration issue ==================== Signed-off-by: -
Jian Shen authored
The FEC capbility may be changed with port speed changes. Driver needs to read the active FEC mode, and update FEC capability when port speed changes. Fixes: 7e6ec914 ("net: hns3: add support for FEC encoding control") Signed-off-by:
Jian Shen <shenjian15@huawei.com> Signed-off-by:
Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by:
-
Jian Shen authored
This patch adds aRFS support for PF. The aRFS rules are also stored in the hardware flow director table, Use the existing filter management functions to insert TCPv4/UDPv4/TCPv6/UDPv6 flow director filters. To avoid rule conflict, once user adds flow director rules with ethtool, the aRFS will be disabled, and clear exist aRFS rules. Once all user configure rules were removed, aRFS can work again. Signed-off-by:
-
Jian Shen authored
In order to be compatible with aRFS rules, this patch adds spin_lock for flow director rule adding, deleting, querying, and packages the rule configuration. Signed-off-by:
-
Jian Shen authored
Allocate CPU rmap and add entry for each irq. CPU rmap is used in aRFS to get the queue number of the rx completion interrupts. In additional, remove the calling of irq_set_affinity_notifier() in hns3_nic_init_irq(), because we have registered notifier in irq_cpu_rmap_add() for each vector, otherwise it may cause use-after-free issue. Signed-off-by:
-
David S. Miller authored
Oleksij Rempel says: ==================== MIPS: ath79: add ag71xx support 2019.05.24 v6: - ag71xx: remove double union - ag71xx: reverse Christmas tree for all functions - ag71xx: add Reviewed-by: Andrew Lunn <andrew@lunn.ch> 2019.05.20 v5: - ag71xx: remove MII_CMD_WRITE, the name is confusing. It is actually disables MII_CMD_READ. - ag71xx: rework ag71xx_mdio_mii_read/write - ag71xx: set proper mask for the addr in ag71xx_mdio_mii_read/write - Kconfig: remove MDIO_BITBANG - ag71xx: ./scripts/checkpatch.pl it. 2019.05.19 v4: - DT: define eth and mdio clocks - ag71xx: remove module parameters - ag71xx: return proper error value on mdio_read/write - ag71xx: use proper mdio clock registration - ag71xx: add ag71xx_dma_wait_stop() for ag71xx_dma_reset() - ag71xx: remove ag71xx_speed_str() - ag71xx: use phydev->link/sped/duplex instead of ag-> variants - ag71xx: use WARN() instead of BUG() - ag71xx: drop big part of ag71xx_phy_link_adjust() - ag71xx: drop most of ag71xx_do_ioctl() - ag71xx: register eth clock - ag71xx: remove AG71XX_ETH0_NO_MDIO quirk. 2019.04.22 v3: - ag71xx: use phy_modes() instead of ag71xx_get_phy_if_mode_name() - ag71xx: remove .ndo_poll_controller support - ag71xx: unregister_netdev before disconnecting phy. 2019.04.18 v2: - ag71xx: add list of openwrt authors - ag71xx: remove redundant PHY_POLL assignment - ag71xx: use phy_attached_info instead of netif_info - ag71xx: remove redundant netif_carrier_off() on .stop. - DT: use "ethernet" instead of "eth" This patch series provide ethernet support for many Atheros/QCA MIPS based SoCs. I reworked ag71xx driver which was previously maintained within OpenWRT repository. So far, following changes was made to make upstreaming easier: - everything what can be some how used in user space was removed. Most of it was debug functionality. - most of deficetree bindings was removed. Not every thing made sense and most of it is SoC specific, so it is possible to detect it by compatible. - mac and mdio parts are merged in to one driver. It makes easier to maintaine SoC specific quirks. ==================== Signed-off-by: -
Oleksij Rempel authored
Add support for Atheros/QCA AR7XXX/AR9XXX/QCA95XX built-in ethernet mac support Reviewed-by:
Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by:
-
Oleksij Rempel authored
Add ethernet nodes supported by ag71xx driver. Signed-off-by:
-
Oleksij Rempel authored
Add binding documentation for Atheros/QCA networking IP core used in many routers. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
David S. Miller authored
Michal Kalderon says: ==================== qed*: Improve performance on 100G link for offload protocols This patch series modifies the current implementation of PF selection. The refactoring of the llh code enables setting additional filters (mac / protocol) per PF, and improves performance for offload protocols (RoCE, iWARP, iSCSI, fcoe) on 100G link (was capped at 90G per single PF). Improved performance on 100G link is achieved by configuring engine affinty to each PF. The engine affinity is read from the Management FW and hw is configured accordingly. A new hw resource called PPFID is exposed and an API is introduced to utilize it. This additional resource enables setting the affinity of a PF and providing more classification rules per PF. qedr,qedi,qedf are also modified as part of the series. Without the changes functionality is broken. v1 --> v2 --------- - Remove iWARP module parameter. Instead use devlink param infrastructure for setting the iwarp_cmt mode. Additional patch added to the series for adding the devlink support. - Fix kbuild test robot warning on qed_llh_filter initialization. - Remove comments inside function calls ==================== Signed-off-by: -
Chad Dupuis authored
MSI-X vector index is determined using qed device information and affinity to use. Signed-off-by:
Chad Dupuis <cdupuis@marvell.com> Signed-off-by:
Saurav Kashyap <skashyap@marvell.com> Signed-off-by:
Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by:
-
Manish Rangankar authored
MSI-X vector index is determined using qed device information and affinity to use. Signed-off-by:
Manish Rangankar <mrangankar@marvell.com> Signed-off-by:
Ariel Elior <ariel.elior@marvell.com> Signed-off-by:
-
Manish Rangankar authored
Always request for number of irqs equals to number of queues. This reverts commit 1a291bce. Signed-off-by:
-
Michal Kalderon authored
Add iWARP engine affinity setting for supporting iWARP over 100g. iWARP cannot be distinguished by the LLH from L2, hence the engine division will affect L2 as well. For this reason we add a parameter to devlink to determine the engine division. Signed-off-by:
-
Michal Kalderon authored
The table currently contains a single parameter for configuring whether iWARP should be enabled on a 100g device. Enabling iWARP on a 100g device impacts L2 performance and is therefore not enabled by default. Signed-off-by:
-
Michal Kalderon authored
In 100g mode the doorbell bar is united for both engines. Set the correct offset in the hwfn so that the doorbell returned for RoCE is in the affined hwfn. Signed-off-by:
Denis Bolotin <denis.bolotin@marvell.com> Signed-off-by:
-
Michal Kalderon authored
Use the msix vectors of the affined hwfn and not the leading one. Signed-off-by:
-
Michal Kalderon authored
To enable 100g support for offload protocols each PF gets a dedicated engine to work on from the MFW. This patch modifies the code to use the affined hwfn instead of the leading one. The offload protocols require the ll2 to be opened on both engines, and not just the affined hwfn. Signed-off-by:
-
