- 14 Jul, 2020 20 commits
-
-
Julian Wiedmann authored
BugLink: https://bugs.launchpad.net/bugs/1885932 [ Upstream commit 75e82bec ] qdio_establish() calls qdio_setup_thinint() via qdio_setup_irq(). If the subsequent qdio_establish_thinint() fails, we miss to put the DSCI again. Thus the DSCI isn't available for re-use. Given enough of such errors, we could end up with having only the shared DSCI available. Merge qdio_setup_thinint() into qdio_establish_thinint(), and deal with such an error internally. Fixes: 779e6e1c ("[S390] qdio: new qdio driver.") Signed-off-by:
Julian Wiedmann <jwi@linux.ibm.com> Reviewed-by:
Benjamin Block <bblock@linux.ibm.com> Signed-off-by:
Vasily Gorbik <gor@linux.ibm.com> Signed-off-by:
Sasha Levin <sashal@kernel.org> Signed-off-by:
Kamal Mostafa <kamal@canonical.com> Signed-off-by:
Kelsey Skunberg <kelsey.skunberg@canonical.com>
-
Alexander Tsoy authored
BugLink: https://bugs.launchpad.net/bugs/1885932 [ Upstream commit f0bd62b6 ] For computation of the the next frame size current value of fs/fps and accumulated fractional parts of fs/fps are used, where values are stored in Q16.16 format. This is quite natural for computing frame size for asynchronous endpoints driven by explicit feedback, since in this case fs/fps is a value provided by the feedback endpoint and it's already in the Q format. If an error is accumulated over time, the device can adjust fs/fps value to prevent buffer overruns/underruns. But for synchronous endpoints the accuracy provided by these computations is not enough. Due to accumulated error the driver periodically produces frames with incorrect size (+/- 1 audio sample). This patch fixes this issue by implementing a different algorithm for frame size computation. It is based on accumulating of the remainders from division fs/fps and it doesn't accumulate errors over time. This new method is enabled for synchronous and adaptive playback endpoints. Signed-off-by:
Alexander Tsoy <alexander@tsoy.me> Link: https://lore.kernel.org/r/20200424022449.14972-1-alexander@tsoy.meSigned-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Tyrel Datwyler authored
BugLink: https://bugs.launchpad.net/bugs/1885932 [ Upstream commit 4919b33b ] The adapter info MAD is used to send the client info and receive the host info as a response. A persistent buffer is used and as such the client info is overwritten after the response. During the course of a normal adapter reset the client info is refreshed in the buffer in preparation for sending the adapter info MAD. However, in the special case of LPM where we reenable the CRQ instead of a full CRQ teardown and reset we fail to refresh the client info in the adapter info buffer. As a result, after Live Partition Migration (LPM) we erroneously report the host's info as our own. [mkp: typos] Link: https://lore.kernel.org/r/20200603203632.18426-1-tyreld@linux.ibm.comSigned-off-by:
Tyrel Datwyler <tyreld@linux.ibm.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Simon Arlott authored
BugLink: https://bugs.launchpad.net/bugs/1885932 [ Upstream commit 6555781b ] If the cdrom fails to be registered then the device minor should be deallocated. Link: https://lore.kernel.org/r/072dac4b-8402-4de8-36bd-47e7588969cd@0882a8b5-c6c3-11e9-b005-00805fc181feSigned-off-by:
Simon Arlott <simon@octiron.net> Signed-off-by:
-
ashimida authored
BugLink: https://bugs.launchpad.net/bugs/1885932 [ Upstream commit 72d24acc ] When System.map was generated, the kernel used mksysmap to filter the kernel symbols, but all the symbols with the second letter 'L' in the kernel were filtered out, not just the symbols starting with 'dot + L'. For example: ashimida@ubuntu:~/linux$ cat System.map |grep ' .L' ashimida@ubuntu:~/linux$ nm -n vmlinux |grep ' .L' ffff0000088028e0 t bLength_show ...... ffff0000092e0408 b PLLP_OUTC_lock ffff0000092e0410 b PLLP_OUTA_lock The original intent should be to filter out all local symbols starting with '.L', so the dot should be escaped. Fixes: 00902e98 ("mksysmap: Add h8300 local symbol pattern") Signed-off-by:
ashimida <ashimida@linux.alibaba.com> Signed-off-by:
Masahiro Yamada <masahiroy@kernel.org> Signed-off-by:
-
Wang Hai authored
BugLink: https://bugs.launchpad.net/bugs/1885932 [ Upstream commit 98749b71 ] If register_netdev(dev) fails, free_netdev(dev) needs to be called, otherwise a memory leak will occur. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Wang Hai <wanghai38@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Pingfan Liu authored
BugLink: https://bugs.launchpad.net/bugs/1885932 [ Upstream commit be5470e0 ] 'mem=" option is an easy way to put high pressure on memory during some test. Hence after applying the memory limit, instead of total mem, the actual usable memory should be considered when reserving mem for crashkernel. Otherwise the boot up may experience OOM issue. E.g. it would reserve 4G prior to the change and 512M afterward, if passing crashkernel="2G-4G:384M,4G-16G:512M,16G-64G:1G,64G-128G:2G,128G-:4G", and mem=5G on a 256G machine. This issue is powerpc specific because it puts higher priority on fadump and kdump reservation than on "mem=". Referring the following code: if (fadump_reserve_mem() == 0) reserve_crashkernel(); ... /* Ensure that total memory size is page-aligned. */ limit = ALIGN(memory_limit ?: memblock_phys_mem_size(), PAGE_SIZE); memblock_enforce_memory_limit(limit); While on other arches, the effect of "mem=" takes a higher priority and pass through memblock_phys_mem_size() before calling reserve_crashkernel(). Signed-off-by:
Pingfan Liu <kernelfans@gmail.com> Reviewed-by:
Hari Bathini <hbathini@linux.ibm.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/1585749644-4148-1-git-send-email-kernelfans@gmail.comSigned-off-by:
-
Xiyu Yang authored
BugLink: https://bugs.launchpad.net/bugs/1885932 [ Upstream commit a4abc6b1 ] nfsd4_process_cb_update() invokes svc_xprt_get(), which increases the refcount of the "c->cn_xprt". The reference counting issue happens in one exception handling path of nfsd4_process_cb_update(). When setup callback client failed, the function forgets to decrease the refcnt increased by svc_xprt_get(), causing a refcnt leak. Fix this issue by calling svc_xprt_put() when setup callback client failed. Signed-off-by:
Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by:
Xin Tan <tanxin.ctf@gmail.com> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Xiyu Yang authored
BugLink: https://bugs.launchpad.net/bugs/1885932 [ Upstream commit 7217e6e6 ] In order to create or activate a new node, lpfc_els_unsol_buffer() invokes lpfc_nlp_init() or lpfc_enable_node() or lpfc_nlp_get(), all of them will return a reference of the specified lpfc_nodelist object to "ndlp" with increased refcnt. When lpfc_els_unsol_buffer() returns, local variable "ndlp" becomes invalid, so the refcount should be decreased to keep refcount balanced. The reference counting issue happens in one exception handling path of lpfc_els_unsol_buffer(). When "ndlp" in DEV_LOSS, the function forgets to decrease the refcnt increased by lpfc_nlp_init() or lpfc_enable_node() or lpfc_nlp_get(), causing a refcnt leak. Fix this issue by calling lpfc_nlp_put() when "ndlp" in DEV_LOSS. Link: https://lore.kernel.org/r/1590416184-52592-1-git-send-email-xiyuyang19@fudan.edu.cnReviewed-by:
Daniel Wagner <dwagner@suse.de> Reviewed-by:
James Smart <james.smart@broadcom.com> Signed-off-by:
-
Marek Szyprowski authored
BugLink: https://bugs.launchpad.net/bugs/1885932 [ Upstream commit d4f9b542 ] WM8994 chip has built-in regulators, which might be used for chip operation. They are controlled by a separate wm8994-regulator driver, which should be loaded before this driver calls regulator_get(), because that driver also provides consumer-supply mapping for the them. If that driver is not yet loaded, regulator core substitute them with dummy regulator, what breaks chip operation, because the built-in regulators are never enabled. Fix this by annotating this driver with MODULE_SOFTDEP() "pre" dependency to "wm8994_regulator" module. Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Acked-by:
Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Qian Cai authored
BugLink: https://bugs.launchpad.net/bugs/1885932 [ Upstream commit 3e63b94b ] vfio_pci_disable() calls vfio_config_free() but forgets to call free_perm_bits() resulting in memory leaks, unreferenced object 0xc000000c4db2dee0 (size 16): comm "qemu-kvm", pid 4305, jiffies 4295020272 (age 3463.780s) hex dump (first 16 bytes): 00 00 ff 00 ff ff ff ff ff ff ff ff ff ff 00 00 ................ backtrace: [<00000000a6a4552d>] alloc_perm_bits+0x58/0xe0 [vfio_pci] [<00000000ac990549>] vfio_config_init+0xdf0/0x11b0 [vfio_pci] init_pci_cap_msi_perm at drivers/vfio/pci/vfio_pci_config.c:1125 (inlined by) vfio_msi_cap_len at drivers/vfio/pci/vfio_pci_config.c:1180 (inlined by) vfio_cap_len at drivers/vfio/pci/vfio_pci_config.c:1241 (inlined by) vfio_cap_init at drivers/vfio/pci/vfio_pci_config.c:1468 (inlined by) vfio_config_init at drivers/vfio/pci/vfio_pci_config.c:1707 [<000000006db873a1>] vfio_pci_open+0x234/0x700 [vfio_pci] [<00000000630e1906>] vfio_group_fops_unl_ioctl+0x8e0/0xb84 [vfio] [<000000009e34c54f>] ksys_ioctl+0xd8/0x130 [<000000006577923d>] sys_ioctl+0x28/0x40 [<000000006d7b1cf2>] system_call_exception+0x114/0x1e0 [<0000000008ea7dd5>] system_call_common+0xf0/0x278 unreferenced object 0xc000000c4db2e330 (size 16): comm "qemu-kvm", pid 4305, jiffies 4295020272 (age 3463.780s) hex dump (first 16 bytes): 00 ff ff 00 ff ff ff ff ff ff ff ff ff ff 00 00 ................ backtrace: [<000000004c71914f>] alloc_perm_bits+0x44/0xe0 [vfio_pci] [<00000000ac990549>] vfio_config_init+0xdf0/0x11b0 [vfio_pci] [<000000006db873a1>] vfio_pci_open+0x234/0x700 [vfio_pci] [<00000000630e1906>] vfio_group_fops_unl_ioctl+0x8e0/0xb84 [vfio] [<000000009e34c54f>] ksys_ioctl+0xd8/0x130 [<000000006577923d>] sys_ioctl+0x28/0x40 [<000000006d7b1cf2>] system_call_exception+0x114/0x1e0 [<0000000008ea7dd5>] system_call_common+0xf0/0x278 Fixes: 89e1f7d4 ("vfio: Add PCI device driver") Signed-off-by:
Qian Cai <cai@lca.pw> [aw: rolled in follow-up patch] Signed-off-by:
Alex Williamson <alex.williamson@redhat.com> Signed-off-by:
-
Emmanuel Nicolet authored
BugLink: https://bugs.launchpad.net/bugs/1885932 [ Upstream commit 720bc316 ] Since commit dcebd755 ("block: use bio_for_each_bvec() to compute multi-page bvec count"), the kernel will bug_on on the PS3 because bio_split() is called with sectors == 0: kernel BUG at block/bio.c:1853! Oops: Exception in kernel mode, sig: 5 [#1] BE PAGE_SIZE=4K MMU=Hash PREEMPT SMP NR_CPUS=8 NUMA PS3 Modules linked in: firewire_sbp2 rtc_ps3(+) soundcore ps3_gelic(+) \ ps3rom(+) firewire_core ps3vram(+) usb_common crc_itu_t CPU: 0 PID: 97 Comm: blkid Not tainted 5.3.0-rc4 #1 NIP: c00000000027d0d0 LR: c00000000027d0b0 CTR: 0000000000000000 REGS: c00000000135ae90 TRAP: 0700 Not tainted (5.3.0-rc4) MSR: 8000000000028032 <SF,EE,IR,DR,RI> CR: 44008240 XER: 20000000 IRQMASK: 0 GPR00: c000000000289368 c00000000135b120 c00000000084a500 c000000004ff8300 GPR04: 0000000000000c00 c000000004c905e0 c000000004c905e0 000000000000ffff GPR08: 0000000000000000 0000000000000001 0000000000000000 000000000000ffff GPR12: 0000000000000000 c0000000008ef000 000000000000003e 0000000000080001 GPR16: 0000000000000100 000000000000ffff 0000000000000000 0000000000000004 GPR20: c00000000062fd7e 0000000000000001 000000000000ffff 0000000000000080 GPR24: c000000000781788 c00000000135b350 0000000000000080 c000000004c905e0 GPR28: c00000000135b348 c000000004ff8300 0000000000000000 c000000004c90000 NIP [c00000000027d0d0] .bio_split+0x28/0xac LR [c00000000027d0b0] .bio_split+0x8/0xac Call Trace: [c00000000135b120] [c00000000027d130] .bio_split+0x88/0xac (unreliable) [c00000000135b1b0] [c000000000289368] .__blk_queue_split+0x11c/0x53c [c00000000135b2d0] [c00000000028f614] .blk_mq_make_request+0x80/0x7d4 [c00000000135b3d0] [c000000000283a8c] .generic_make_request+0x118/0x294 [c00000000135b4b0] [c000000000283d34] .submit_bio+0x12c/0x174 [c00000000135b580] [c000000000205a44] .mpage_bio_submit+0x3c/0x4c [c00000000135b600] [c000000000206184] .mpage_readpages+0xa4/0x184 [c00000000135b750] [c0000000001ff8fc] .blkdev_readpages+0x24/0x38 [c00000000135b7c0] [c0000000001589f0] .read_pages+0x6c/0x1a8 [c00000000135b8b0] [c000000000158c74] .__do_page_cache_readahead+0x118/0x184 [c00000000135b9b0] [c0000000001591a8] .force_page_cache_readahead+0xe4/0xe8 [c00000000135ba50] [c00000000014fc24] .generic_file_read_iter+0x1d8/0x830 [c00000000135bb50] [c0000000001ffadc] .blkdev_read_iter+0x40/0x5c [c00000000135bbc0] [c0000000001b9e00] .new_sync_read+0x144/0x1a0 [c00000000135bcd0] [c0000000001bc454] .vfs_read+0xa0/0x124 [c00000000135bd70] [c0000000001bc7a4] .ksys_read+0x70/0xd8 [c00000000135be20] [c00000000000a524] system_call+0x5c/0x70 Instruction dump: 7fe3fb78 482e30dc 7c0802a6 482e3085 7c9e2378 f821ff71 7ca42b78 7d3e00d0 7c7d1b78 79290fe0 7cc53378 69290001 <0b090000> 81230028 7bca0020 7929ba62 [ end trace 313fec760f30aa1f ]--- The problem originates from setting the segment boundary of the request queue to -1UL. This makes get_max_segment_size() return zero when offset is zero, whatever the max segment size. The test with BLK_SEG_BOUNDARY_MASK fails and 'mask - (mask & offset) + 1' overflows to zero in the return statement. Not setting the segment boundary and using the default value (BLK_SEG_BOUNDARY_MASK) fixes the problem. Signed-off-by:
Emmanuel Nicolet <emmanuel.nicolet@gmail.com> Signed-off-by:
Geoff Levand <geoff@infradead.org> Signed-off-by:
-
Oliver Neukum authored
BugLink: https://bugs.launchpad.net/bugs/1885932 [ Upstream commit 296a193b ] syzkaller reported an URB that should have been killed to be active. We do not understand it, but this should fix the issue if it is real. Signed-off-by:
Oliver Neukum <oneukum@suse.com> Reported-by: syzbot+be5b5f86a162a6c281e6@syzkaller.appspotmail.com Link: https://lore.kernel.org/r/20200507085806.5793-1-oneukum@suse.comSigned-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Russell King authored
BugLink: https://bugs.launchpad.net/bugs/1885932 [ Upstream commit e81c979f ] If we timeout during a message transfer, the control register may contain bits that cause an action to be set. Read-modify-writing the register leaving these bits set may trigger the hardware to attempt one of these actions unintentionally. Always clear these bits when cleaning up after a message or after a timeout. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
Wolfram Sang <wsa@kernel.org> Signed-off-by:
-
Viacheslav Dubeyko authored
BugLink: https://bugs.launchpad.net/bugs/1885932 [ Upstream commit 803e4555 ] The goal of the following command sequence is to restart the adapter. However, the tgt_stop flag remains set, indicating that the adapter is still in stopping state even after re-enabling it. echo 0x7fffffff > /sys/module/qla2xxx/parameters/logging modprobe target_core_mod modprobe tcm_qla2xxx mkdir /sys/kernel/config/target/qla2xxx mkdir /sys/kernel/config/target/qla2xxx/<port-name> mkdir /sys/kernel/config/target/qla2xxx/<port-name>/tpgt_1 echo 1 > /sys/kernel/config/target/qla2xxx/<port-name>/tpgt_1/enable echo 0 > /sys/kernel/config/target/qla2xxx/<port-name>/tpgt_1/enable echo 1 > /sys/kernel/config/target/qla2xxx/<port-name>/tpgt_1/enable kernel: PID 1396:qla_target.c:1555 qlt_stop_phase1(): tgt_stop 0x0, tgt_stopped 0x0 kernel: qla2xxx [0001:00:02.0]-e803:1: PID 1396:qla_target.c:1567: Stopping target for host 1(c0000000033557e8) kernel: PID 1396:qla_target.c:1579 qlt_stop_phase1(): tgt_stop 0x1, tgt_stopped 0x0 kernel: PID 1396:qla_target.c:1266 qlt_schedule_sess_for_deletion(): tgt_stop 0x1, tgt_stopped 0x0 kernel: qla2xxx [0001:00:02.0]-e801:1: PID 1396:qla_target.c:1316: Scheduling sess c00000002d5cd800 for deletion 21:00:00:24:ff:7f:35:c7 <skipped> kernel: qla2xxx [0001:00:02.0]-290a:1: PID 340:qla_target.c:1187: qlt_unreg_sess sess c00000002d5cd800 for deletion 21:00:00:24:ff:7f:35:c7 <skipped> kernel: qla2xxx [0001:00:02.0]-f801:1: PID 340:qla_target.c:1145: Unregistration of sess c00000002d5cd800 21:00:00:24:ff:7f:35:c7 finished fcp_cnt 0 kernel: PID 340:qla_target.c:1155 qlt_free_session_done(): tgt_stop 0x1, tgt_stopped 0x0 kernel: qla2xxx [0001:00:02.0]-4807:1: PID 346:qla_os.c:6329: ISP abort scheduled. <skipped> kernel: qla2xxx [0001:00:02.0]-28f1:1: PID 346:qla_os.c:3956: Mark all dev lost kernel: PID 346:qla_target.c:1266 qlt_schedule_sess_for_deletion(): tgt_stop 0x1, tgt_stopped 0x0 kernel: qla2xxx [0001:00:02.0]-4808:1: PID 346:qla_os.c:6338: ISP abort end. <skipped> kernel: PID 1396:qla_target.c:6812 qlt_enable_vha(): tgt_stop 0x1, tgt_stopped 0x0 <skipped> kernel: qla2xxx [0001:00:02.0]-4807:1: PID 346:qla_os.c:6329: ISP abort scheduled. <skipped> kernel: qla2xxx [0001:00:02.0]-4808:1: PID 346:qla_os.c:6338: ISP abort end. qlt_handle_cmd_for_atio() rejects the request to send commands because the adapter is in the stopping state: kernel: PID 0:qla_target.c:4442 qlt_handle_cmd_for_atio(): tgt_stop 0x1, tgt_stopped 0x0 kernel: qla2xxx [0001:00:02.0]-3861:1: PID 0:qla_target.c:4447: New command while device c000000005314600 is shutting down kernel: qla2xxx [0001:00:02.0]-e85f:1: PID 0:qla_target.c:5728: qla_target: Unable to send command to target This patch calls qla_stop_phase2() in addition to qlt_stop_phase1() in tcm_qla2xxx_tpg_enable_store() and tcm_qla2xxx_npiv_tpg_enable_store(). The qlt_stop_phase1() marks adapter as stopping (tgt_stop == 0x1, tgt_stopped == 0x0) but qlt_stop_phase2() marks adapter as stopped (tgt_stop == 0x0, tgt_stopped == 0x1). Link: https://lore.kernel.org/r/52be1e8a3537f6c5407eae3edd4c8e08a9545ea5.camel@yadro.comReviewed-by:
Roman Bolshakov <r.bolshakov@yadro.com> Reviewed-by:
Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by:
Viacheslav Dubeyko <v.dubeiko@yadro.com> Signed-off-by:
-
Dan Carpenter authored
BugLink: https://bugs.launchpad.net/bugs/1885932 [ Upstream commit 7f0d5053 ] The "header->number" comes from the ioctl and it needs to be clamped to prevent out of bounds writes. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20200501094011.GA960082@mwandaSigned-off-by:
-
Bryan O'Donoghue authored
BugLink: https://bugs.launchpad.net/bugs/1885932 [ Upstream commit f47ab3c2 ] During the process of debugging a processor derived from the msm8916 which we found the new processor was not starting one of its PLLs. After tracing the addresses and writes that downstream was doing and comparing to upstream it became obvious that we were writing to a different register location than downstream when trying to configure the PLL. This error is also present in upstream msm8916. As an example clk-pll.c::clk_pll_recalc_rate wants to write to pll->config_reg updating the bit-field POST_DIV_RATIO. That bit-field is defined in PLL_USER_CTL not in PLL_CONFIG_CTL. Taking the BIMC PLL as an example lm80-p0436-13_c_qc_snapdragon_410_processor_hrd.pdf 0x01823010 GCC_BIMC_PLL_USER_CTL 0x01823014 GCC_BIMC_PLL_CONFIG_CTL This pattern is repeated for gpll0, gpll1, gpll2 and bimc_pll. This error is likely not apparent since the bootloader will already have initialized these PLLs. This patch corrects the location of config_reg from PLL_CONFIG_CTL to PLL_USER_CTL for all relevant PLLs on msm8916. Fixes commit 3966fab8 ("clk: qcom: Add MSM8916 Global Clock Controller support") Cc: Georgi Djakov <georgi.djakov@linaro.org> Cc: Andy Gross <agross@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Stephen Boyd <sboyd@kernel.org> Signed-off-by:
Bryan O'Donoghue <bryan.odonoghue@linaro.org> Link: https://lkml.kernel.org/r/20200329124116.4185447-1-bryan.odonoghue@linaro.orgSigned-off-by:
Stephen Boyd <sboyd@kernel.org> Signed-off-by:
-
Adam Honse authored
BugLink: https://bugs.launchpad.net/bugs/1885932 [ Upstream commit f27237c1 ] The AMD X370 and other AM4 chipsets (A/B/X 3/4/5 parts) and Threadripper equivalents have a secondary SMBus controller at I/O port address 0x0B20. This bus is used by several manufacturers to control motherboard RGB lighting via embedded controllers. I have been using this bus in my OpenRGB project to control the Aura RGB on many motherboards and ASRock also uses this bus for their Polychrome RGB controller. I am not aware of any CZ-compatible platforms which do not have the second SMBus channel. All of AMD's AM4- and Threadripper- series chipsets that OpenRGB users have tested appear to have this secondary bus. I also noticed this secondary bus is present on older AMD platforms including my FM1 home server. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202587Signed-off-by:
Adam Honse <calcprogrammer1@gmail.com> Reviewed-by:
Jean Delvare <jdelvare@suse.de> Reviewed-by:
Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Rikard Falkeborn authored
BugLink: https://bugs.launchpad.net/bugs/1885932 [ Upstream commit ee25d974 ] round_down() can only round to powers of 2. If round_down() is asked to round to something that is not a power of 2, incorrect results are produced. The incorrect results can be both too large and too small. Instead, use rounddown() which can round to any number. Fixes: 6a721db1 ("clk: sunxi: Add A31 clocks support") Signed-off-by:
Rikard Falkeborn <rikard.falkeborn@gmail.com> Signed-off-by:
Maxime Ripard <maxime@cerno.tech> Signed-off-by:
-
Dmitry V. Levin authored
BugLink: https://bugs.launchpad.net/bugs/1885932 commit b3583fca upstream. If both the tracer and the tracee are compat processes, and gprs[2] is assigned a value by __poke_user_compat, then the higher 32 bits of gprs[2] are cleared, IS_ERR_VALUE() always returns false, and syscall_get_error() always returns 0. Fix the implementation by sign-extending the value for compat processes the same way as x86 implementation does. The bug was exposed to user space by commit 201766a2 ("ptrace: add PTRACE_GET_SYSCALL_INFO request") and detected by strace test suite. This change fixes strace syscall tampering on s390. Link: https://lkml.kernel.org/r/20200602180051.GA2427@altlinux.org Fixes: 753c4dd6 ("[S390] ptrace changes") Cc: Elvira Khabirova <lineprinter@altlinux.org> Cc: stable@vger.kernel.org # v2.6.28+ Signed-off-by:
Dmitry V. Levin <ldv@altlinux.org> Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
-
- 01 Jul, 2020 3 commits
-
-
Khalid Elmously authored
Signed-off-by:Khalid Elmously <khalid.elmously@canonical.com>
-
Khalid Elmously authored
BugLink: https://bugs.launchpad.net/bugs/1885514 Properties: no-test-build Signed-off-by:
-
Khalid Elmously authored
Ignore: yes Signed-off-by:
-
- 30 Jun, 2020 17 commits
-
-
Kamal Mostafa authored
BugLink: https://bugs.launchpad.net/bugs/1884564 Ignore: yes Signed-off-by:
-
Greg Kroah-Hartman authored
BugLink: https://bugs.launchpad.net/bugs/1884564Signed-off-by:
-
Adrian Hunter authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 85afd355 upstream. Reportedly, from 19.10 Ubuntu has begun mixing up the location of some debug symbol files, putting files expected to be in /usr/lib/debug/usr/lib into /usr/lib/debug/lib instead. Fix by adding another dso_binary_type. Example on Ubuntu 20.04 Before: $ perf record -e intel_pt//u uname Linux [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 0.030 MB perf.data ] $ perf script --call-trace | head -5 uname 14003 [005] 15321.764958566: cbr: 42 freq: 4219 MHz (156%) uname 14003 [005] 15321.764958566: (/usr/lib/x86_64-linux-gnu/ld-2.31.so ) 7f1e71cc4100 uname 14003 [005] 15321.764961566: (/usr/lib/x86_64-linux-gnu/ld-2.31.so ) 7f1e71cc4df0 uname 14003 [005] 15321.764961900: (/usr/lib/x86_64-linux-gnu/ld-2.31.so ) 7f1e71cc4e18 uname 14003 [005] 15321.764963233: (/usr/lib/x86_64-linux-gnu/ld-2.31.so ) 7f1e71cc5128 After: $ perf script --call-trace | head -5 uname 14003 [005] 15321.764958566: cbr: 42 freq: 4219 MHz (156%) uname 14003 [005] 15321.764958566: (/usr/lib/x86_64-linux-gnu/ld-2.31.so ) _start uname 14003 [005] 15321.764961566: (/usr/lib/x86_64-linux-gnu/ld-2.31.so ) _dl_start uname 14003 [005] 15321.764961900: (/usr/lib/x86_64-linux-gnu/ld-2.31.so ) _dl_start uname 14003 [005] 15321.764963233: (/usr/lib/x86_64-linux-gnu/ld-2.31.so ) _dl_start Reported-by:
Travis Downs <travis.downs@gmail.com> Signed-off-by:
Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: stable@vger.kernel.org Link: http://lore.kernel.org/lkml/20200526155207.9172-1-adrian.hunter@intel.comSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Masami Hiramatsu authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit f41ebe9d upstream. When a probe point is expanded to several places (like inlined) and if some of them are skipped because of blacklisted or __init function, those trace_events has no event name. It must be skipped while showing results. Without this fix, you can see "(null):(null)" on the list, # ./perf probe request_resource reserve_setup is out of .text, skip it. Added new events: (null):(null) (on request_resource) probe:request_resource (on request_resource) You can now use it in all perf tools, such as: perf record -e probe:request_resource -aR sleep 1 # With this fix, it is ignored: # ./perf probe request_resource reserve_setup is out of .text, skip it. Added new events: probe:request_resource (on request_resource) You can now use it in all perf tools, such as: perf record -e probe:request_resource -aR sleep 1 # Fixes: 5a51fcd1 ("perf probe: Skip kernel symbols which is out of .text") Signed-off-by:
Masami Hiramatsu <mhiramat@kernel.org> Tested-by:
-
H. Nikolaus Schaller authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 5e02f3b3 upstream. Otherwise it will corrupt the console log during debugging. Fixes: 7b5362a6 ("w1: omap_hdq: Fix some error/debug handling.") Cc: stable@vger.kernel.org Acked-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
H. Nikolaus Schaller <hns@goldelico.com> Link: https://lore.kernel.org/r/cd0d55749a091214106575f6e1d363c6db56622f.1590255176.git.hns@goldelico.comSigned-off-by:
-
NeilBrown authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 24c5efe4 upstream. gss_mech_register() calls svcauth_gss_register_pseudoflavor() for each flavour, but gss_mech_unregister() does not call auth_domain_put(). This is unbalanced and makes it impossible to reload the module. Change svcauth_gss_register_pseudoflavor() to return the registered auth_domain, and save it for later release. Cc: stable@vger.kernel.org (v2.6.12+) Link: https://bugzilla.kernel.org/show_bug.cgi?id=206651Signed-off-by:
NeilBrown <neilb@suse.de> Signed-off-by:
-
NeilBrown authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit d47a5dc2 upstream. There is no valid case for supporting duplicate pseudoflavor registrations. Currently the silent acceptance of such registrations is hiding a bug. The rpcsec_gss_krb5 module registers 2 flavours but does not unregister them, so if you load, unload, reload the module, it will happily continue to use the old registration which now has pointers to the memory were the module was originally loaded. This could lead to unexpected results. So disallow duplicate registrations. Link: https://bugzilla.kernel.org/show_bug.cgi?id=206651 Cc: stable@vger.kernel.org (v2.6.12+) Signed-off-by:
-
Masahiro Yamada authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 4b50c8c4 upstream. This code does not work as stated in the comment. $(CONFIG_MODVERSIONS) is always empty because it is expanded before include/config/auto.conf is included. Hence, 'make modules' with CONFIG_MODVERSION=y cannot record the version CRCs. This has been broken since 2003, commit ("kbuild: Enable modules to be build using the "make dir/" syntax"). [1] [1]: https://git.kernel.org/pub/scm/linux/kernel/git/history/history.git/commit/?id=15c6240cdc44bbeef3c4797ec860f9765ef4f1a7 Cc: linux-stable <stable@vger.kernel.org> # v2.5.71+ Signed-off-by:
-
Michael Ellerman authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 93900337 upstream. create_cpu_loop() calls smu_sat_get_sdb_partition() which does kmalloc() and returns the allocated buffer. In fact it's called twice, and neither buffer is freed. This results in a memory leak as reported by Erhard: unreferenced object 0xc00000047081f840 (size 32): comm "kwindfarm", pid 203, jiffies 4294880630 (age 5552.877s) hex dump (first 32 bytes): c8 06 02 7f ff 02 ff 01 fb bf 00 41 00 20 00 00 ...........A. .. 00 07 89 37 00 a0 00 00 00 00 00 00 00 00 00 00 ...7............ backtrace: [<0000000083f0a65c>] .smu_sat_get_sdb_partition+0xc4/0x2d0 [windfarm_smu_sat] [<000000003010fcb7>] .pm112_wf_notify+0x104c/0x13bc [windfarm_pm112] [<00000000b958b2dd>] .notifier_call_chain+0xa8/0x180 [<0000000070490868>] .blocking_notifier_call_chain+0x64/0x90 [<00000000131d8149>] .wf_thread_func+0x114/0x1a0 [<000000000d54838d>] .kthread+0x13c/0x190 [<00000000669b72bc>] .ret_from_kernel_thread+0x58/0x64 unreferenced object 0xc0000004737089f0 (size 16): comm "kwindfarm", pid 203, jiffies 4294880879 (age 5552.050s) hex dump (first 16 bytes): c4 04 01 7f 22 11 e0 e6 ff 55 7b 12 ec 11 00 00 ...."....U{..... backtrace: [<0000000083f0a65c>] .smu_sat_get_sdb_partition+0xc4/0x2d0 [windfarm_smu_sat] [<00000000b94ef7e1>] .pm112_wf_notify+0x1294/0x13bc [windfarm_pm112] [<00000000b958b2dd>] .notifier_call_chain+0xa8/0x180 [<0000000070490868>] .blocking_notifier_call_chain+0x64/0x90 [<00000000131d8149>] .wf_thread_func+0x114/0x1a0 [<000000000d54838d>] .kthread+0x13c/0x190 [<00000000669b72bc>] .ret_from_kernel_thread+0x58/0x64 Fix it by rearranging the logic so we deal with each buffer separately, which then makes it easy to free the buffer once we're done with it. Fixes: ac171c46 ("[PATCH] powerpc: Thermal control for dual core G5s") Cc: stable@vger.kernel.org # v2.6.16+ Reported-by:
Erhard F. <erhard_f@mailbox.org> Signed-off-by:
-
Dmitry Osipenko authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 35509737 upstream. The PL310 Auxiliary Control Register shouldn't have the "Full line of zero" optimization bit being set before L2 cache is enabled. The L2X0 driver takes care of enabling the optimization by itself. This patch fixes a noisy error message on Tegra20 and Tegra30 telling that cache optimization is erroneously enabled without enabling it for the CPU: L2C-310: enabling full line of zeros but not enabled in Cortex-A9 Cc: <stable@vger.kernel.org> Signed-off-by:
Dmitry Osipenko <digetx@gmail.com> Tested-by:
Nicolas Chauvet <kwizart@gmail.com> Signed-off-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
-
Douglas Anderson authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit b5945214 upstream. cpu_pm_notify() is basically a wrapper of notifier_call_chain(). notifier_call_chain() doesn't initialize *nr_calls to 0 before it starts incrementing it--presumably it's up to the callers to do this. Unfortunately the callers of cpu_pm_notify() don't init *nr_calls. This potentially means you could get too many or two few calls to CPU_PM_ENTER_FAILED or CPU_CLUSTER_PM_ENTER_FAILED depending on the luck of the stack. Let's fix this. Fixes: ab10023e ("cpu_pm: Add cpu power management notifiers") Cc: stable@vger.kernel.org Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by:
Stephen Boyd <swboyd@chromium.org> Reviewed-by:
Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20200504104917.v6.3.I2d44fc0053d019f239527a4e5829416714b7e299@changeidSigned-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by:
-
Al Viro authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit cf51e129 upstream. It needs access_process_vm() if the traced process does not share mm with the caller. Solution is similar to what sparc64 does. Note that genregs32_set() is only ever called with pos being 0 or 32 * sizeof(u32) (the latter - as part of PTRACE_SETREGS handling). Cc: stable@kernel.org Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Jonathan Bakker authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit f354157a upstream. Currently, for EINT_TYPE GPIOs, the CON and FLTCON registers are saved and restored over a suspend/resume cycle. However, the EINT_MASK registers are not. On S5PV210 at the very least, these registers are not retained over suspend, leading to the interrupts remaining masked upon resume and therefore no interrupts being triggered for the device. There should be no effect on any SoCs that do retain these registers as theoretically we would just be re-writing what was already there. Fixes: 7ccbc60c ("pinctrl: exynos: Handle suspend/resume of GPIO EINT registers") Cc: <stable@vger.kernel.org> Signed-off-by:
Jonathan Bakker <xc-racer2@live.ca> Signed-off-by:
Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by:
-
Anders Roxell authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 73174acc upstream. Make sure that the POWER_RESET_VEXPRESS driver won't have bind/unbind attributes available via the sysfs, so lets be explicit here and use ".suppress_bind_attrs = true" to prevent userspace from doing something silly. Link: https://lore.kernel.org/r/20200527112608.3886105-2-anders.roxell@linaro.org Cc: stable@vger.kernel.org Signed-off-by:
Anders Roxell <anders.roxell@linaro.org> Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Kai-Heng Feng authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 165ae7a8 upstream. igb device gets runtime suspended when there's no link partner. We can't get correct speed under that state: $ cat /sys/class/net/enp3s0/speed 1000 In addition to that, an error can also be spotted in dmesg: [ 385.991957] igb 0000:03:00.0 enp3s0: PCIe link lost Since device can only be runtime suspended when there's no link partner, we can skip reading register and let the following logic set speed and duplex with correct status. The more generic approach will be wrap get_link_ksettings() with begin() and complete() callbacks. However, for this particular issue, begin() calls igb_runtime_resume() , which tries to rtnl_lock() while the lock is already hold by upper ethtool layer. So let's take this approach until the igb_runtime_resume() no longer needs to hold rtnl_lock. CC: stable <stable@vger.kernel.org> Suggested-by:
Alexander Duyck <alexander.duyck@gmail.com> Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Larry Finger authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 6a29d134 upstream. Since the driver was first introduced into the kernel, it has only handled the ciphers associated with WEP, WPA, and WPA2. It fails with WPA3 even though mac80211 can handle those additional ciphers in software, b43legacy did not report that it could handle them. By setting MFP_CAPABLE using ieee80211_set_hw(), the problem is fixed. With this change, b43legacy will handle the ciphers it knows in hardware, and let mac80211 handle the others in software. It is not necessary to use the module parameter NOHWCRYPT to turn hardware encryption off. Although this change essentially eliminates that module parameter, I am choosing to keep it for cases where the hardware is broken, and software encryption is required for all ciphers. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200526155909.5807-3-Larry.Finger@lwfinger.netSigned-off-by:
-
Larry Finger authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 75d057bd upstream. Since the driver was first introduced into the kernel, it has only handled the ciphers associated with WEP, WPA, and WPA2. It fails with WPA3 even though mac80211 can handle those additional ciphers in software, b43 did not report that it could handle them. By setting MFP_CAPABLE using ieee80211_set_hw(), the problem is fixed. With this change, b43 will handle the ciphers it knows in hardware, and let mac80211 handle the others in software. It is not necessary to use the module parameter NOHWCRYPT to turn hardware encryption off. Although this change essentially eliminates that module parameter, I am choosing to keep it for cases where the hardware is broken, and software encryption is required for all ciphers. Reported-and-tested-by:
Rui Salvaterra <rsalvaterra@gmail.com> Signed-off-by:
-
