Enable USB0 on the EA4357 devkit and setup the required USB0
control pins.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

All devices in the LPC18xx/43xx familiy contain a ARM PL172
MultiPort Memory Controller (MPMC).
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

NXP LPC185x and LPC435x/70 devices contain a ARM PL111 lcd controller.
Signed-off-by: Joachim Eastwood <joachim.eastwood@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Add the USB OTG phy under the CREG syscon node and attach it to
the USB0 EHCI controller.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

mvebu dt changes for v4.3 (part #2)

Add support Buffalo Linkstation LS-WTGL

* tag 'mvebu-dt-4.3-2' of git://git.infradead.org/linux-mvebu:
  ARM: dts: orion5x: add buffalo linkstation ls-wtgl
Signed-off-by: Olof Johansson <olof@lixom.net>

arm: Xilinx Zynq dt patches for v4.3

- Add ECC for Synopsys MC
- Add OCM, pushbuttons to zc702

* tag 'zynq-dt-for-4.3' of https://github.com/Xilinx/linux-xlnx:
  ARM: zynq: DT: Add zc702 pushbuttons to DT as gpio-keys
  ARM: zynq: DT: Add missing interrupt for L2 pl310
  Documentation: devicetree: Add ECC information to synopsys ddr controller
  ARM: dts: zynq: Add OCM node
Signed-off-by: Olof Johansson <olof@lixom.net>

Qualcomm ARM Based Device Tree Updates for v4.3

* Switch to use pinctrl compatible for GPIOs
* Add RPM regulators for MSM8960
* Add SPI Ethernet support on MSM8960 CDP
* Add SMEM support along with dependencies
* Add PM8921 support for GPIO and MPP
* Fix GSBI cell index
* Switch to use real regulators on APQ8064 w/ SDCC

* tag 'qcom-dt-for-4.3' of git://codeaurora.org/quic/kernel/agross-msm:
  ARM: dts: qs600: Add real regulators to sdcc
  ARM: dts: ifc6410: add real regulators for sdcc nodes.
  ARM: dts: apq8064: remove temporary fixed regulator for mmc
  ARM: dts: apq8064: fix missing gsbi cell-index
  ARM: dts: apq8064: Add DT support for GSBI6 and for UART pin mux
  ARM: dts: apq8064: add pm8921 mpp support
  ARM: dts: apq8064: Add pm8921 mfd and its gpio node
  ARM: dts: msm8974: Add smem reservation and node
  ARM: dts: msm8974: Add tcsr mutex node
  ARM: dts: qcom: Add ks8851 node for wired ethernet
  ARM: dts: qcom: Add MSM8960 CDP RPM regulators
  ARM: dts: qcom: Add MSM8960 RPM and RPM regulator nodes
  ARM: dts: qcom: Replace gpio node with pinctrl node
  ARM: dts: qcom: Replace gpio node with pinctrl node
Signed-off-by: Olof Johansson <olof@lixom.net>

First batch of DT changes for 4.3:
- some fixes on sama5d4 ADC definition
- adding Image Sensor Interface (aka ISI) on at91sam9m10g45ek board
- update rst controller compatible string on sama5 machines
- new sama5d2 DT definition and its reference board:
  the sama5d2 Xplained. Minimal configuration for now.

* tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
  ARM: at91/dt: add minimal sama5d2 Xplained board
  ARM: at91/dt: add basic dtsi for sama5d2 SoC
  ARM: at91/dt: sama5: update rstc to correct compatible string
  ARM: at91/dt: add isi & ov2640 dt nodes for at91sam9m10g45ek board
  ARM: at91/dt: sama5d4: move ADC pinctrl to board device trees
  ARM: at91/dt: sama5d4: fix external trigger property
Signed-off-by: Olof Johansson <olof@lixom.net>

Adds the two MIO connected pushbuttons on the zc702 board to the devicetree as a
single multi-key device for us with the gpio-keys driver.
Signed-off-by: Ezra Savard <ezra.savard@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add pl310 interrupt to the Zynq devicetree.
Signed-off-by: Alex Wilson <alex.david.wilson@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add ECC information to synopsys ddr memory controller.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add OCM node for all zynq boards. OCM location
can changed but for all current boards this
is the location where OCM is.`
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add minimal support for the new sama5d2 Xplained board. Only USB,
spi/i2c, ethernet and uart/usart peripherals added.
With this DTS file you can boot the board and begin to play with it.
Rootfs on NFS and sd card have successfully been tested.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Only the basic support for this new Atmel Cortex-A5 SoC. A subset of the
peripherals is setup to allow booting.
IRQ, clocks, USB, crypto, timers, rtc, ethernet, spi/i2c and
uart/usart peripheral nodes are added.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

They'll use "atmel,sama5d3-rstc" for reset function.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
[nicolas.ferre@atmel.com: add the old compatible string as a fallback]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

First we group the isi data pins, and for now we only use 0~7 data pins
with HSYNC and VSYNC.
Also add the link for atmel-isi and ov2640 sensor node.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
[nicolas.ferre@atmel.com: move the pinctrl properties in board .dts file]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

This patch adds real regulators to sdcc nodes.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>

This patch adds real regulators for all the three sdcc nodes.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>

This patch removes temporary fixed regluator use for mmc.
Board files should use the regulators which are wiredup appropriately.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>

Merge tag 'socfpga_dts_for_v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt

SoCFPGA DTS updates for v4.3
- Update clocking for DTS nodes
- Add DTS board file for Terasic DE0 Atlas board
- Use stdout-patch for chosen node
- Enable prefetch-data and prefetch-instr

* tag 'socfpga_dts_for_v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
  ARM: socfpga: dts: add osc1 as a possible parent for dbg_base_clk
  ARM: socfpga: dts: add missing clock gates to socfpga.dtsi
  ARM: socfpga: dts: Fix gpio dts entry for the correct clock
  ARM: socfpga: dts: Correct the parent clock for l3_sp_clk and dbg_clk
  ARM: dts: socfpga: Add support of Terasic DE0 Atlas board
  ARM: dts: socfpga: use stdout-path for chosen node
  ARM: dts: socfpga: enable the data and instruction prefetch for the l2 cache
Signed-off-by: Olof Johansson <olof@lixom.net>

- ARM: dts: mediatek: add mt6580 basic support
- Document: DT: Add bindings for mediatek MT6580 SoC Platform
- ARM: dts: mediatek mt8135: Use real UART clocks
- ARM: dts: mt8135-evbp1: Add PMIC support
- ARM: dts: mt8135: Add pmic wrapper nodes
- ARM: dts: mediatek: Enable clock support for Mediatek MT8135.

* tag 'v4.2-next-dts' of https://github.com/mbgg/linux-mediatek:
  ARM: dts: mediatek: add mt6580 basic support
  Document: DT: Add bindings for mediatek MT6580 SoC Platform
  ARM: dts: mediatek mt8135: Use real UART clocks
  ARM: dts: mt8135-evbp1: Add PMIC support
  ARM: dts: mt8135: Add pmic wrapper nodes
  ARM: dts: mediatek: Enable clock support for Mediatek MT8135.
Signed-off-by: Olof Johansson <olof@lixom.net>

The ADC pinctrl is board specific, move it to the board device trees.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The property is actually atmel,adc-use-external-triggers.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Without this i2c instance for missing cell-index nodes would fail, fix
it by adding correct cell-index.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>

This change adds DT support for GSBI6 and muxes the gpio pins
as UART lines. Also defines a alias for serial port on these lines.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
[Srinivas Kandagatla]: fix pinctrl location and rename alias correctly
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>

This patch adds pmic pm8921 mpp gpio controller node.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>

This patch adds pmic gpio node to the device tree, this node is
necessary for devices like wlan to control reset gpio.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>

The DT nodes in uniphier-pinctrl.dtsi provide the default pinctrl
settings that would be suitable for most boards.  You can still
override them in your board DTS file if necessary.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Add the pinctrol device nodes for UniPhier PH1-LD4, PH1-Pro4,
and PH1-sLD8.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v4.3/dt-dm814x' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

omap dts changes for minimal dm814x support for v4.3 merge window.

These changes make dm814x boot and adds minimal board support for
dm814x-evm and hp t410.

Note that to boot these depend on omap-for-v4.3/soc-signed branch,
but as dm814x support is currently broken, these can be merged
separately with the other dts changes.

* tag 'omap-for-v4.3/dt-dm814x' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: Add custom abort handler for t410
  ARM: dts: Add minimal support for HP T410
  ARM: dts: Add minimal dts support for dm8148-evm
  ARM: dts: Add minimal clocks for dm814x
  ARM: dts: Add minimal dm814x support
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-dt2-for-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Second Round of Renesas ARM Based SoC DT Updates for v4.3

* Add Audio MIX and CTU support to r8a779[01] SoCs
* Correct IRQ sense for adv7511 on lager board
* Add sound label to koelsch and lager boards
* Add IIC support to emev2 SoC

* tag 'renesas-dt2-for-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: r8a7791: Add Audio MIX support on DTSI
  ARM: shmobile: r8a7791: Add Audio CTU support on DTSI
  ARM: shmobile: r8a7790: Add Audio MIX support on DTSI
  ARM: shmobile: r8a7790: Add Audio CTU support on DTSI
  ARM: shmobile: lager: Fix adv7511 IRQ sensing
  ARM: shmobile: koelsch: add sound label on DTS
  ARM: shmobile: lager: add sound label on DTS
  ARM: shmobile: emev2: kzm9d: enable IIC busses
  ARM: shmobile: emev2: add IIC cores to dtsi
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'stm32-dt-for-v4.3-1b' of https://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/stm32 into next/dt

STM32 DT updates for v4.3, round 1.

Highlights:
-----------
 - Add RCC clocks support to STM32F429
 - Add STM32429i-EVAL board support
 - Use stdout-path instead of linux,stdout-path in Disco board

* tag 'stm32-dt-for-v4.3-1b' of https://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/stm32:
  ARM: dts: Use stdout-path in STM32F429 Discovery board
  ARM: dts: Add STM32429i-EVAL board support
  ARM: dts: stm32f429: Adopt STM32F4 clock driver
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'sti-dt-for-v4.3-1' of https://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/sti into next/dt

STi DT update for v4.3, round 1.

Highlights:
-----------
 - Add pinctrl configurations for transport stream channels
 - Add cpu-release-addr properties to STiH407 and STiH418
 - Add PWM regulator support so STIH407 family
 - Add BDISP node to STiH407

* tag 'sti-dt-for-v4.3-1' of https://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/sti:
  ARM: DT: STiH410: Add bdisp dt nodes
  ARM: STi: STiH407: Add PWM Regulator node
  ARM: STi: STiH407: Move PWM nodes STiH407 => STiH407-family
  ARM: STi: DT: Rename st_pll3200c32_407_c0_x into st_pll3200c32_cx_x
  ARM: STi: DT: STiH418: Add cpu-release-addr dt property.
  ARM: STi: DT: STiH407: Add cpu-release-addr dt property.
  ARM: STi: DT: Add STiH407 family mtsin0 pinctrl configuration
  ARM: STi: DT: Add STiH407 family tsout1 pinctrl configuration
  ARM: STi: DT: Add STiH407 family tsout0 pinctrl configuration
  ARM: STi: DT: Add STiH407 family tsin5 pinctrl configuration
  ARM: STi: DT: Add STiH407 family tsin4 pinctrl configuration
  ARM: STi: DT: Add STiH407 family tsin3 pinctrl configuration
  ARM: STi: DT: Add STiH407 family tsin2 pinctrl configuration
  ARM: STi: DT: Add STiH407 family tsin1 pinctrl configuration
  ARM: STi: DT: Add STiH407 family tsin0 pinctrl configuration
Signed-off-by: Olof Johansson <olof@lixom.net>

Add dts file to support Buffalo Linkstation LS-WTGL,
which is marvell orion5x based 2-bay 3.5" HDD NAS.
Product info:
 - (JPN) http://buffalo.jp/products/catalog/storage/ls-wtgl_r1/
 - (ENG) http://www.buffalotech.com/support-and-downloads/download/LinkStation_Pro_Duo_Manual_web.pdfSigned-off-by: Roger Shimizu <rogershimizu@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

The dbg_base_clk can also have osc1 has a parent.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>

Similar to commit fdf4850c ("ARM: BCM5301X: workaround suppress fault"),
let's add custom handling for the aborts on t410 that prevent booting:

Unhandled fault: imprecise external abort (0xc06) at 0xee091fb0
pgd = ee4bc000
[ee091fb0] *pgd=ae00041e(bad)
Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000007

Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add minimal support for HP T410.

Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add minimal dts support for dm8148-evm.

Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use fixed clocks until we have a clock driver for the PLL.
The mux and divider composite clocks work the same way
as on dm816x and am335x.

Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add minimal dm814x support.

Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>