- 19 Apr, 2015 40 commits
-
-
Ilya Dryomov authored
commit 6d7fdb0a upstream. This reverts commit 89baaa57. Dirty page throttling should be sufficient for us in the general case so there is no need to use __GFP_MEMALLOC - it would be needed only in the swap-over-rbd case, which we currently don't support. (It would probably take approximately the commit that is being reverted to add that support, but we would also need the "swap" option to distinguish from the general case and make sure swap ceph_client-s aren't shared with anything else.) See ceph-devel threads [1] and [2] for the details of why enabling pfmemalloc reserves for all cases is a bad thing. On top of potential system lockups related to drained emergency reserves, this turned out to cause ceph lockups in case peers are on the same host and communicating via loopback due to sk_filter() dropping pfmemalloc skbs on the receiving side because the receiving loopback socket is not tagged with SOCK_MEMALLOC. [1] "SOCK_MEMALLOC vs loopback" http://www.spinics.net/lists/ceph-devel/msg22998.html [2] "[PATCH] libceph: don't set memalloc flags in loopback case" http://www.spinics.net/lists/ceph-devel/msg23392.html Conflicts: net/ceph/messenger.c [ context: tcp_nodelay option ] Cc: Mike Christie <michaelc@cs.wisc.edu> Cc: Mel Gorman <mgorman@suse.de> Cc: Sage Weil <sage@redhat.com> Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Acked-by:
Mike Christie <michaelc@cs.wisc.edu> Acked-by:
Mel Gorman <mgorman@suse.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Rafael J. Wysocki authored
commit f82daee4 upstream. Commit 84c91b7a (PM / hibernate: avoid unsafe pages in e820 reserved regions) is reported to make resume from hibernation on Lenovo x230 unreliable, so revert it. We will revisit the issue the commit in question was supposed to fix in the future. Link: https://bugzilla.kernel.org/show_bug.cgi?id=96111Reported-by:
rhn <kebuac.rhn@porcupinefactory.org> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Benjamin Herrenschmidt authored
commit 41d94893 upstream. The "sdc" node is missing the ranges property, it needs to be treated as having an empty one otherwise translation fails for its children. Fixes 746c9e9f, "of/base: Fix PowerPC address parsing hack" Tested-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
Grant Likely <grant.likely@linaro.org> Signed-off-by:
-
Larry Finger authored
commit be0b5e63 upstream. Transmission of an AP beacon does not call the TX interrupt service routine, which usually does the cleanup. Instead, cleanup is handled in a tasklet completion routine. Unfortunately, this routine has a serious bug in that it does not release the DMA mapping before it frees the skb, thus one IOMMU mapping is leaked for each beacon. The test system failed with no free IOMMU mapping slots approximately one hour after hostapd was used to start an AP. This issue was reported and tested at https://github.com/lwfinger/rtlwifi_new/issues/30. Reported-and-tested-by:
Kevin Mullican <kevin@mullican.com> Cc: Kevin Mullican <kevin@mullican.com> Signed-off-by:
Shao Fu <shaofu@realtek.com> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Alex Williamson authored
commit 71684406 upstream. Device domains never span IOMMU hardware units, which allows the domain ID space for each IOMMU to be an independent address space. Therefore we can have multiple, independent domains, each with the same domain->id, but attached to different hardware units. This is also why we need to do a heavy-weight search for VM domains since they can span multiple IOMMUs hardware units and we don't require a single global ID to use for all hardware units. Therefore, if we call iommu_detach_domain() across all active IOMMU hardware units for a non-VM domain, the result is that we clear domain IDs that are not associated with our domain, allowing them to be re-allocated and causing apparent coherency issues when the device cannot access IOVAs for the intended domain. This bug was introduced in commit fb170fb4 ("iommu/vt-d: Introduce helper functions to make code symmetric for readability"), but is significantly exacerbated by the more recent commit 62c22167 ("iommu/vt-d: Fix dmar_domain leak in iommu_attach_device") which calls domain_exit() more frequently to resolve a domain leak. Fixes: fb170fb4 ("iommu/vt-d: Introduce helper functions to make code symmetric for readability") Signed-off-by:
Alex Williamson <alex.williamson@redhat.com> Cc: Jiang Liu <jiang.liu@linux.intel.com> Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
-
Arend van Spriel authored
commit f93a25b3 upstream. The BCM43362 firmware falsely reports it is capable of providing MBSS. As a result AP mode no longer works for this device. Therefor disable MBSS in the driver for this chipset. Reported-by:
Jorg Krause <jkrause@posteo.de> Reviewed-by:
Hante Meuleman <meuleman@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
-
David Disseldorp authored
commit e1e9bda2 upstream. Under intermittent network outages, find_writable_file() is susceptible to the following race condition, which results in a user-after-free in the cifs_writepages code-path: Thread 1 Thread 2 ======== ======== inv_file = NULL refind = 0 spin_lock(&cifs_file_list_lock) // invalidHandle found on openFileList inv_file = open_file // inv_file->count currently 1 cifsFileInfo_get(inv_file) // inv_file->count = 2 spin_unlock(&cifs_file_list_lock); cifs_reopen_file() cifs_close() // fails (rc != 0) ->cifsFileInfo_put() spin_lock(&cifs_file_list_lock) // inv_file->count = 1 spin_unlock(&cifs_file_list_lock) spin_lock(&cifs_file_list_lock); list_move_tail(&inv_file->flist, &cifs_inode->openFileList); spin_unlock(&cifs_file_list_lock); cifsFileInfo_put(inv_file); ->spin_lock(&cifs_file_list_lock) // inv_file->count = 0 list_del(&cifs_file->flist); // cleanup!! kfree(cifs_file); spin_unlock(&cifs_file_list_lock); spin_lock(&cifs_file_list_lock); ++refind; // refind = 1 goto refind_writable; At this point we loop back through with an invalid inv_file pointer and a refind value of 1. On second pass, inv_file is not overwritten on openFileList traversal, and is subsequently dereferenced. Signed-off-by:
David Disseldorp <ddiss@suse.de> Reviewed-by:
Jeff Layton <jlayton@samba.org> Signed-off-by:
Steve French <smfrench@gmail.com> Signed-off-by:
-
Sachin Prabhu authored
commit 2477bc58 upstream. While attempting to clone a file on a samba server, we receive a STATUS_INVALID_DEVICE_REQUEST. This is mapped to -EOPNOTSUPP which isn't handled in smb2_clone_range(). We end up looping in the while loop making same call to the samba server over and over again. The proposed fix is to exit and return the error value when encountered with an unhandled error. Signed-off-by:
Sachin Prabhu <sprabhu@redhat.com> Signed-off-by:
Steve French <steve.french@primarydata.com> Signed-off-by:
-
Peter Hurley authored
commit fb5ef9e7 upstream. In canon mode, the read buffer head will advance over the buffer tail if the input > 4095 bytes without receiving a line termination char. Discard additional input until a line termination is received. Before evaluating for overflow, the 'room' value is normalized for I_PARMRK and 1 byte is reserved for line termination (even in !icanon mode, in case the mode is switched). The following table shows the transform: actual buffer | 'room' value before overflow calc space avail | !I_PARMRK | I_PARMRK -------------------------------------------------- 0 | -1 | -1 1 | 0 | 0 2 | 1 | 0 3 | 2 | 0 4+ | 3 | 1 When !icanon or when icanon and the read buffer contains newlines, normalized 'room' values of -1 and 0 are clamped to 0, and 'overflow' is 0, so read_head is not adjusted and the input i/o loop exits (setting no_room if called from flush_to_ldisc()). No input is discarded since the reader does have input available to read which ensures forward progress. When icanon and the read buffer does not contain newlines and the normalized 'room' value is 0, then overflow and room are reset to 1, so that the i/o loop will process the next input char normally (except for parity errors which are ignored). Thus, erasures, signalling chars, 7-bit mode, etc. will continue to be handled properly. If the input char processed was not a line termination char, then the canon_head index will not have advanced, so the normalized 'room' value will now be -1 and 'overflow' will be set, which indicates the read_head can safely be reset, effectively erasing the last char processed. If the input char processed was a line termination, then the canon_head index will have advanced, so 'overflow' is cleared to 0, the read_head is not reset, and 'room' is cleared to 0, which exits the i/o loop (because the reader now have input available to read which ensures forward progress). Note that it is possible for a line termination to be received, and for the reader to copy the line to the user buffer before the input i/o loop is ready to process the next input char. This is why the i/o loop recomputes the room/overflow state with every input char while handling overflow. Finally, if the input data was processed without receiving a line termination (so that overflow is still set), the pty driver must receive a write wakeup. A pty writer may be waiting to write more data in n_tty_write() but without unthrottling here that wakeup will not arrive, and forward progress will halt. (Normally, the pty writer is woken when the reader reads data out of the buffer and more space become available). Signed-off-by:
Peter Hurley <peter@hurleysoftware.com> Signed-off-by:
Joseph Salisbury <joseph.salisbury@canonical.com>
-
Stefan Agner authored
commit 8e4934c6 upstream. When the receiver was enabled during startup, a character could have been in the FIFO when the UART get initially used. The driver configures the (receive) watermark level, and flushes the FIFO. However, the receive flag (RDRF) could still be set at that stage (as mentioned in the register description of UARTx_RWFIFO). This leads to an interrupt which won't be handled properly in interrupt mode: The receive interrupt function lpuart_rxint checks the FIFO count, which is 0 at that point (due to the flush during initialization). The problem does not manifest when using DMA to receive characters. Fix this situation by explicitly read the status register, which leads to clearing of the RDRF flag. Due to the flush just after the status flag read, a explicit data read is not to required. Signed-off-by:
Stefan Agner <stefan@agner.ch> Signed-off-by:
-
Stefan Agner authored
commit 4e8f2459 upstream. Specify transmit FIFO size which might be different depending on LPUART instance. This makes sure uart_wait_until_sent in serial core getting called, which in turn waits and checks if the FIFO is really empty on shutdown by using the tx_empty callback. Without the call of this callback, the last several characters might not yet be transmitted when closing the serial port. This can be reproduced by simply using echo and redirect the output to a ttyLP device. Signed-off-by:
-
Lu Baolu authored
commit 227a4fd8 upstream. When a device with an isochronous endpoint is plugged into the Intel xHCI host controller, and the driver submits multiple frames per URB, the xHCI driver will set the Block Event Interrupt (BEI) flag on all but the last TD for the URB. This causes the host controller to place an event on the event ring, but not send an interrupt. When the last TD for the URB completes, BEI is cleared, and we get an interrupt for the whole URB. However, under Intel xHCI host controllers, if the event ring is full of events from transfers with BEI set, an "Event Ring is Full" event will be posted to the last entry of the event ring, but no interrupt is generated. Host will cease all transfer and command executions and wait until software completes handling the pending events in the event ring. That means xHC stops, but event of "event ring is full" is not notified. As the result, the xHC looks like dead to user. This patch is to apply XHCI_AVOID_BEI quirk to Intel xHC devices. And it should be backported to kernels as old as 3.0, that contains the commit 69e848c2 ("Intel xhci: Support EHCI/xHCI port switching."). Signed-off-by:
Lu Baolu <baolu.lu@linux.intel.com> Tested-by:
Alistair Grant <akgrant0710@gmail.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Lu Baolu authored
commit 9425183d upstream. Linux xHCI driver doesn't report and handle port cofig error change. If Port Configure Error for root hub port occurs, CEC bit in PORTSC would be set by xHC and remains 1. This happends when the root port fails to configure its link partner, e.g. the port fails to exchange port capabilities information using Port Capability LMPs. Then the Port Status Change Events will be blocked until all status change bits(CEC is one of the change bits) are cleared('0') (refer to xHCI spec 4.19.2). Otherwise, the port status change event for this root port will not be generated anymore, then root port would look like dead for user and can't be recovered until a Host Controller Reset(HCRST). This patch is to check CEC bit in PORTSC in xhci_get_port_status() and set a Config Error in the return status if CEC is set. This will cause a ClearPortFeature request, where CEC bit is cleared in xhci_clear_port_change_bit(). [The commit log is based on initial Marvell patch posted at http://marc.info/?l=linux-kernel&m=142323612321434&w=2] Reported-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
-
Thomas Schlichter authored
commit c7e8bdf5 upstream. Fix a bug that leads to showing the name and description of C-state C0 as "<null>" in sysfs after the ACPI C-states changed (e.g. after AC->DC or DC->AC transition). The function poll_idle_init() in drivers/cpuidle/driver.c initializes the state 0 during cpuidle_register_driver(), so we better do not overwrite it again with '\0' during acpi_processor_cst_has_changed(). Signed-off-by:
Thomas Schlichter <thomas.schlichter@web.de> Reviewed-by:
Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
commit d75e4af1 upstream. Thomas Schlichter reports the following issue on his Samsung NC20: "The C-states C1 and C2 to the OS when connected to AC, and additionally provides the C3 C-state when disconnected from AC. However, the number of C-states shown in sysfs is fixed to the number of C-states present at boot. If I boot with AC connected, I always only see the C-states up to C2 even if I disconnect AC. The reason is commit 130a5f69 (ACPI / cpuidle: remove dev->state_count setting). It removes the update of dev->state_count, but sysfs uses exactly this variable to show the C-states. The fix is to use drv->state_count in sysfs. As this is currently the last user of dev->state_count, this variable can be completely removed." Remove dev->state_count as per the above. Reported-by:
Kyungmin Park <kyungmin.park@samsung.com> Acked-by:
Daniel Lezcano <daniel.lezcano@linaro.org> [ rjw: Changelog ] Signed-off-by:
-
Jean Delvare authored
commit bfbaafae upstream. dmi_num is a u16, dmi_len is a u32, so this construct: dmi_num = dmi_len / 4; would result in an integer overflow for a DMI table larger than 256 kB. I've never see such a large table so far, but SMBIOS 3.0 makes it possible so maybe we'll see such tables in the future. So instead of faking a structure count when the entry point does not provide it, adjust the loop condition in dmi_table() to properly deal with the case where dmi_num is not set. This bug was introduced with the initial SMBIOS 3.0 support in commit fc430262 ("dmi: add support for SMBIOS 3.0 64-bit entry point"). Signed-off-by:
Jean Delvare <jdelvare@suse.de> Cc: Matt Fleming <matt.fleming@intel.com> Cc: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Acked-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by:
Matt Fleming <matt.fleming@intel.com> Signed-off-by:
-
Andreas Werner authored
commit 555828ef upstream. Return EPROBE_DEFER if Regulator returns EPROBE_DEFER If the Flexcan driver is built into kernel and a regulator is used to enable the CAN transceiver, the Flexcan driver may not use the regulator. When initializing the Flexcan device with a regulator defined in the device tree, but not initialized, the regulator subsystem returns EPROBE_DEFER, hence the Flexcan init fails. The solution for this is to return EPROBE_DEFER if regulator is not initialized and wait until the regulator is initialized. Signed-off-by:
Andreas Werner <kernel@andy89.org> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Andri Yngvason authored
commit 258ce80e upstream. Making sure that the bus-off state gets passed to can_change_state(). Signed-off-by:
Andri Yngvason <andri.yngvason@marel.com> Signed-off-by:
-
Stefan Lippers-Hollmann authored
commit 80313b30 upstream. The ASRock Q1900DC-ITX mainboard (Baytrail-D) hangs randomly in both BIOS and UEFI mode while rebooting unless reboot=pci is used. Add a quirk to reboot via the pci method. The problem is very intermittent and hard to debug, it might succeed rebooting just fine 40 times in a row - but fails half a dozen times the next day. It seems to be slightly less common in BIOS CSM mode than native UEFI (with the CSM disabled), but it does happen in either mode. Since I've started testing this patch in late january, rebooting has been 100% reliable. Most of the time it already hangs during POST, but occasionally it might even make it through the bootloader and the kernel might even start booting, but then hangs before the mode switch. The same symptoms occur with grub-efi, gummiboot and grub-pc, just as well as (at least) kernel 3.16-3.19 and 4.0-rc6 (I haven't tried older kernels than 3.16). Upgrading to the most current mainboard firmware of the ASRock Q1900DC-ITX, version 1.20, does not improve the situation. ( Searching the web seems to suggest that other Bay Trail-D mainboards might be affected as well. ) -- Signed-off-by:
Stefan Lippers-Hollmann <s.l-h@gmx.de> Cc: Matt Fleming <matt.fleming@intel.com> Link: http://lkml.kernel.org/r/20150330224427.0fb58e42@mirSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Felix Fietkau authored
commit 1cf48f22 upstream. sc->nbcnvifs tracks assigned beacon slots, not enabled beacons. Therefore, it cannot be used to decide if cur_conf->enable_beacon (bool) should be updated, or if beacons have been enabled already. With the current code (depending on the order of calls), beacons often do not get enabled in an AP+STA setup. To fix tracking of enabled beacons, convert cur_conf->enable_beacon to a bitmask of enabled beacon slots. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
-
Peter Ujfalusi authored
commit 02d88b73 upstream. In omap_dma_start_desc the vdesc->node is removed from the virt-dma framework managed lists (to be precise from the desc_issued list). If a terminate_all comes before the transfer finishes the omap_desc will not be freed up because it is not in any of the lists and we stopped the DMA channel so the transfer will not going to complete. There is no special sequence for leaking memory when using cyclic (audio) transfer: with every start and stop of a cyclic transfer the driver leaks struct omap_desc worth of memory. Free up the allocated memory directly in omap_dma_terminate_all() since the framework will not going to do that for us. Signed-off-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> CC: <linux-omap@vger.kernel.org> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Petr Kulhavy authored
commit 5ca9e7ce upstream. If edma_terminate_all() was called while a transfer was running (i.e. after edma_execute() but before edma_callback()) the echan->edesc was not freed. This was due to the fact that a running transfer is on none of the vchan lists: desc_submitted, desc_issued, desc_completed (edma_execute() removes it from the desc_issued list), so the vchan_dma_desc_free_list() called at the end of edma_terminate_all() didn't find it and didn't free it. This bug was found on an AM1808 based hardware (very similar to da850evm, however using the second MMC/SD controller), where intense operations on the SD card wasted the device 128MB RAM within a couple of days. Peter Ujfalusi: The issue is even more severe since it affects cyclic (audio) transfers as well. In this case starting/stopping audio will results memory leak. Signed-off-by:
Petr Kulhavy <petr@barix.com> Signed-off-by:
-
Darshana Padmadas authored
commit 4ce7ca89 upstream. This patch uses iio_trigger_get to increment the reference count of trigger device, to avoid incorrect assignment. Can result in a null pointer dereference during removal if the trigger has been changed before removal. This patch refers to a similar situation encountered through the following discussion: http://www.spinics.net/lists/linux-iio/msg13669.htmlSigned-off-by:
Darshana Padmadas <darshanapadmadas@gmail.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Stefan Agner authored
commit f54e9f2b upstream. Depending on conversion mode used, the ADC clock (ADCK) needs to be below a maximum frequency. According to Vybrid's data sheet this is 20MHz for the low power conversion mode. The ADC clock is depending on input clock, which is the bus clock by default. Vybrid SoC are typically clocked at at 400MHz or 500MHz, which leads to 66MHz or 83MHz bus clock respectively. Hence, a divider of 8 is required to stay below the specified maximum clock of 20MHz. Due to the different bus clock speeds, the resulting sampling frequency is not static. Hence use the ADC clock and calculate the actual available sampling frequency dynamically. This fixes bogous values observed on some 500MHz clocked Vybrid SoC. The resulting value usually showed Bit 9 being stuck at 1, or 0, which lead to a value of +/-512. Signed-off-by:
Fugang Duan <B38611@freescale.com> Signed-off-by:
-
Sathyanarayanan Kuppuswamy authored
commit 0ba8da96 upstream. Currently driver reports device bandwidth list as available sampling frequency. But sampling frequency is actually twice the device bandwidth. This patch fixes this issue. Signed-off-by:
Sathyanarayanan Kuppuswamy <sathyanarayanan.kuppuswamy@intel.com> Signed-off-by:
Octavian Purdila <octavian.purdila@intel.com> Signed-off-by:
-
Martin Fuzzey authored
commit c1b03ab5 upstream. When an error occurred during event registration memory was freed twice resulting in kernel memory corruption and a crash in unrelated code. The problem was caused by iio_device_unregister_eventset() iio_device_unregister_sysfs() being called twice, once on the error path and then again via iio_dev_release(). Fix this by making these two functions idempotent so they may be called multiple times. The problem was observed before applying 78b33216 iio:core: Handle error when mask type is not separate Signed-off-by:
Martin Fuzzey <mfuzzey@parkeon.com> Signed-off-by:
-
Viorel Suman authored
commit 4dac0a8e upstream. A hardware fifo reset always imply an invalidation of the existing timestamps, so we'll clear timestamps fifo on successfull hardware fifo reset. Signed-off-by:
Viorel Suman <viorel.suman@gmail.com> Signed-off-by:
-
Bart Van Assche authored
commit bba0bdd7 upstream. SCSI transport drivers and SCSI LLDs block a SCSI device if the transport layer is not operational. This means that in this state no requests should be processed, even if the REQ_PREEMPT flag has been set. This patch avoids that a rescan shortly after a cable pull sporadically triggers the following kernel oops: BUG: unable to handle kernel paging request at ffffc9001a6bc084 IP: [<ffffffffa04e08f2>] mlx4_ib_post_send+0xd2/0xb30 [mlx4_ib] Process rescan-scsi-bus (pid: 9241, threadinfo ffff88053484a000, task ffff880534aae100) Call Trace: [<ffffffffa0718135>] srp_post_send+0x65/0x70 [ib_srp] [<ffffffffa071b9df>] srp_queuecommand+0x1cf/0x3e0 [ib_srp] [<ffffffffa0001ff1>] scsi_dispatch_cmd+0x101/0x280 [scsi_mod] [<ffffffffa0009ad1>] scsi_request_fn+0x411/0x4d0 [scsi_mod] [<ffffffff81223b37>] __blk_run_queue+0x27/0x30 [<ffffffff8122a8d2>] blk_execute_rq_nowait+0x82/0x110 [<ffffffff8122a9c2>] blk_execute_rq+0x62/0xf0 [<ffffffffa000b0e8>] scsi_execute+0xe8/0x190 [scsi_mod] [<ffffffffa000b2f3>] scsi_execute_req+0xa3/0x130 [scsi_mod] [<ffffffffa000c1aa>] scsi_probe_lun+0x17a/0x450 [scsi_mod] [<ffffffffa000ce86>] scsi_probe_and_add_lun+0x156/0x480 [scsi_mod] [<ffffffffa000dc2f>] __scsi_scan_target+0xdf/0x1f0 [scsi_mod] [<ffffffffa000dfa3>] scsi_scan_host_selected+0x183/0x1c0 [scsi_mod] [<ffffffffa000edfb>] scsi_scan+0xdb/0xe0 [scsi_mod] [<ffffffffa000ee13>] store_scan+0x13/0x20 [scsi_mod] [<ffffffff811c8d9b>] sysfs_write_file+0xcb/0x160 [<ffffffff811589de>] vfs_write+0xce/0x140 [<ffffffff81158b53>] sys_write+0x53/0xa0 [<ffffffff81464592>] system_call_fastpath+0x16/0x1b [<00007f611c9d9300>] 0x7f611c9d92ff Reported-by:
Max Gurtuvoy <maxg@mellanox.com> Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by:
James Bottomley <JBottomley@Odin.com> Signed-off-by:
-
Doug Goldstein authored
commit b229a0f8 upstream. This patch uses the existing CALAO Systems ftdi_8u2232c_probe in order to avoid attaching a TTY to the JTAG port as this board is based on the CALAO Systems reference design and needs the same fix up. Signed-off-by:
Doug Goldstein <cardoe@cardoe.com> [johan: clean up probe logic ] Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Doug Goldstein authored
commit 4899c054 upstream. Synapse Wireless uses the FTDI VID with a custom PID of 0x9090 for their SNAP Stick 200 product. Signed-off-by:
-
Nathaniel W Filardo authored
commit 5e71fc86 upstream. Add USB VID/PID for Xircom PGMFHUB USB/serial component. (The hub and SCSI bridge on that hardware are recognized out of the box by existing drivers.) Tested VID/PID using new_id and loopback connection and was met with success, but that's all the testing done. Signed-off-by:
Nathaniel Wesley Filardo <nwf@cs.jhu.edu> Signed-off-by:
-
David Miller authored
commit f2c9e560 upstream. Use readb() and memcpy_fromio() accessors instead. Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Martin K. Petersen authored
commit 6fc4d97a upstream. Blacklist queued TRIM on this drive for now. Reported-by:
Stefan Keller <linux-list@zahlenfresser.de> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Martin K. Petersen authored
commit ff7f53fb upstream. Micron has released an updated firmware (MU02) for M510/M550/MX100 drives to fix the issues with queued TRIM. Queued TRIM remains broken on M500 but is working fine on later drives such as M600 and MX200. Tweak our blacklist to reflect the above. Link: https://bugzilla.kernel.org/show_bug.cgi?id=71371Signed-off-by:
-
Tejun Heo authored
commit c72efb65 upstream. From 1ebf33901ecc75d9496862dceb1ef0377980587c Mon Sep 17 00:00:00 2001 From: Tejun Heo <tj@kernel.org> Date: Mon, 23 Mar 2015 00:08:19 -0400 2f800fbd ("writeback: fix dirtied pages accounting on redirty") introduced account_page_redirty() which reverts stat updates for a redirtied page, making BDI_DIRTIED no longer monotonically increasing. bdi_update_write_bandwidth() uses the delta in BDI_DIRTIED as the basis for bandwidth calculation. While unlikely, since the above patch, the newer value may be lower than the recorded past value and underflow the bandwidth calculation leading to a wild result. Fix it by subtracing min of the old and new values when calculating delta. AFAIK, there hasn't been any report of it happening but the resulting erratic behavior would be non-critical and temporary, so it's possible that the issue is happening without being reported. The risk of the fix is very low, so tagged for -stable. Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Tejun Heo authored
commit 7d70e154 upstream. global_update_bandwidth() uses static variable update_time as the timestamp for the last update but forgets to initialize it to INITIALIZE_JIFFIES. This means that global_dirty_limit will be 5 mins into the future on 32bit and some large amount jiffies into the past on 64bit. This isn't critical as the only effect is that global_dirty_limit won't be updated for the first 5 mins after booting on 32bit machines, especially given the auxiliary nature of global_dirty_limit's role - protecting against global dirty threshold's sudden dips; however, it does lead to unintended suboptimal behavior. Fix it. Fixes: c42843f2 ("writeback: introduce smoothed global dirty limit") Signed-off-by:
Jan Kara <jack@suse.cz> Cc: Wu Fengguang <fengguang.wu@intel.com> Cc: Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Viresh Kumar authored
commit c75de0ac upstream. All CPUs leaving the first-online CPU are hotplugged out on suspend and and cpufreq core stops managing them. On resume, we need to call cpufreq_update_policy() for this CPU's policy to make sure its frequency is in sync with cpufreq's cached value, as it might have got updated by hardware during suspend/resume. The policies are always added to the top of the policy-list. So, in normal circumstances, CPU 0's policy will be the last one in the list. And so the code checks for the last policy. But there are cases where it will fail. Consider quad-core system, with policy-per core. If CPU0 is hotplugged out and added back again, the last policy will be on CPU1 :( To fix this in a proper way, always look for the policy of the first online CPU. That way we will be sure that we are calling cpufreq_update_policy() for the only CPU that wasn't hotplugged out. Fixes: 2f0aea93 ("cpufreq: suspend governors on system suspend/hibernate") Reported-by:
Saravana Kannan <skannan@codeaurora.org> Signed-off-by:
Viresh Kumar <viresh.kumar@linaro.org> Acked-by:
-
Brian Silverman authored
commit 746db944 upstream. When non-realtime tasks get priority-inheritance boosted to a realtime scheduling class, RLIMIT_RTTIME starts to apply to them. However, the counter used for checking this (the same one used for SCHED_RR timeslices) was not getting reset. This meant that tasks running with a non-realtime scheduling class which are repeatedly boosted to a realtime one, but never block while they are running realtime, eventually hit the timeout without ever running for a time over the limit. This patch resets the realtime timeslice counter when un-PI-boosting from an RT to a non-RT scheduling class. I have some test code with two threads and a shared PTHREAD_PRIO_INHERIT mutex which induces priority boosting and spins while boosted that gets killed by a SIGXCPU on non-fixed kernels but doesn't with this patch applied. It happens much faster with a CONFIG_PREEMPT_RT kernel, and does happen eventually with PREEMPT_VOLUNTARY kernels. Signed-off-by:
Brian Silverman <brian@peloton-tech.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: austin@peloton-tech.com Link: http://lkml.kernel.org/r/1424305436-6716-1-git-send-email-brian@peloton-tech.comSigned-off-by:
-
Laura Abbott authored
commit cfa86943 upstream. Commit 3c605096 ("mm/page_alloc: restrict max order of merging on isolated pageblock") changed the logic of unset_migratetype_isolate to check the buddy allocator and explicitly call __free_pages to merge. The page that is being freed in this path never had prep_new_page called so set_page_refcounted is called explicitly but there is no call to kernel_map_pages. With the default kernel_map_pages this is mostly harmless but if kernel_map_pages does any manipulation of the page tables (unmapping or setting pages to read only) this may trigger a fault: alloc_contig_range test_pages_isolated(ceb00, ced00) failed Unable to handle kernel paging request at virtual address ffffffc0cec00000 pgd = ffffffc045fc4000 [ffffffc0cec00000] *pgd=0000000000000000 Internal error: Oops: 9600004f [#1] PREEMPT SMP Modules linked in: exfatfs CPU: 1 PID: 23237 Comm: TimedEventQueue Not tainted 3.10.49-gc72ad36-dirty #1 task: ffffffc03de52100 ti: ffffffc015388000 task.ti: ffffffc015388000 PC is at memset+0xc8/0x1c0 LR is at kernel_map_pages+0x1ec/0x244 Fix this by calling kernel_map_pages to ensure the page is set in the page table properly Fixes: 3c605096 ("mm/page_alloc: restrict max order of merging on isolated pageblock") Signed-off-by:
Laura Abbott <lauraa@codeaurora.org> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Mel Gorman <mgorman@suse.de> Acked-by:
Rik van Riel <riel@redhat.com> Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com> Cc: Xishi Qiu <qiuxishi@huawei.com> Cc: Vladimir Davydov <vdavydov@parallels.com> Acked-by:
Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Gioh Kim <gioh.kim@lge.com> Cc: Michal Nazarewicz <mina86@mina86.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Vlastimil Babka <vbabka@suse.cz> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Gu Zheng authored
commit b0dc3a34 upstream. Qiu Xishi reported the following BUG when testing hot-add/hot-remove node under stress condition: BUG: unable to handle kernel paging request at 0000000000025f60 IP: next_online_pgdat+0x1/0x50 PGD 0 Oops: 0000 [#1] SMP ACPI: Device does not support D3cold Modules linked in: fuse nls_iso8859_1 nls_cp437 vfat fat loop dm_mod coretemp mperf crc32c_intel ghash_clmulni_intel aesni_intel ablk_helper cryptd lrw gf128mul glue_helper aes_x86_64 pcspkr microcode igb dca i2c_algo_bit ipv6 megaraid_sas iTCO_wdt i2c_i801 i2c_core iTCO_vendor_support tg3 sg hwmon ptp lpc_ich pps_core mfd_core acpi_pad rtc_cmos button ext3 jbd mbcache sd_mod crc_t10dif scsi_dh_alua scsi_dh_rdac scsi_dh_hp_sw scsi_dh_emc scsi_dh ahci libahci libata scsi_mod [last unloaded: rasf] CPU: 23 PID: 238 Comm: kworker/23:1 Tainted: G O 3.10.15-5885-euler0302 #1 Hardware name: HUAWEI TECHNOLOGIES CO.,LTD. Huawei N1/Huawei N1, BIOS V100R001 03/02/2015 Workqueue: events vmstat_update task: ffffa800d32c0000 ti: ffffa800d32ae000 task.ti: ffffa800d32ae000 RIP: 0010: next_online_pgdat+0x1/0x50 RSP: 0018:ffffa800d32afce8 EFLAGS: 00010286 RAX: 0000000000001440 RBX: ffffffff81da53b8 RCX: 0000000000000082 RDX: 0000000000000000 RSI: 0000000000000082 RDI: 0000000000000000 RBP: ffffa800d32afd28 R08: ffffffff81c93bfc R09: ffffffff81cbdc96 R10: 00000000000040ec R11: 00000000000000a0 R12: ffffa800fffb3440 R13: ffffa800d32afd38 R14: 0000000000000017 R15: ffffa800e6616800 FS: 0000000000000000(0000) GS:ffffa800e6600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000025f60 CR3: 0000000001a0b000 CR4: 00000000001407e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: refresh_cpu_vm_stats+0xd0/0x140 vmstat_update+0x11/0x50 process_one_work+0x194/0x3d0 worker_thread+0x12b/0x410 kthread+0xc6/0xd0 ret_from_fork+0x7c/0xb0 The cause is the "memset(pgdat, 0, sizeof(*pgdat))" at the end of try_offline_node, which will reset all the content of pgdat to 0, as the pgdat is accessed lock-free, so that the users still using the pgdat will panic, such as the vmstat_update routine. process A: offline node XX: vmstat_updat() refresh_cpu_vm_stats() for_each_populated_zone() find online node XX cond_resched() offline cpu and memory, then try_offline_node() node_set_offline(nid), and memset(pgdat, 0, sizeof(*pgdat)) zone = next_zone(zone) pg_data_t *pgdat = zone->zone_pgdat; // here pgdat is NULL now next_online_pgdat(pgdat) next_online_node(pgdat->node_id); // NULL pointer access So the solution here is postponing the reset of obsolete pgdat from try_offline_node() to hotadd_new_pgdat(), and just resetting pgdat->nr_zones and pgdat->classzone_idx to be 0 rather than the memset 0 to avoid breaking pointer information in pgdat. Signed-off-by:
Gu Zheng <guz.fnst@cn.fujitsu.com> Reported-by:
Xishi Qiu <qiuxishi@huawei.com> Suggested-by:
KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: David Rientjes <rientjes@google.com> Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Cc: Taku Izumi <izumi.taku@jp.fujitsu.com> Cc: Tang Chen <tangchen@cn.fujitsu.com> Cc: Xie XiuQi <xiexiuqi@huawei.com> Signed-off-by:
-
