- 02 Jun, 2015 27 commits
-
-
Thadeu Lima de Souza Cascardo authored
commit 47cc84ce upstream. When more than a multicast address is present in a MLDv2 report, all but the first address is ignored, because the code breaks out of the loop if there has not been an error adding that address. This has caused failures when two guests connected through the bridge tried to communicate using IPv6. Neighbor discoveries would not be transmitted to the other guest when both used a link-local address and a static address. This only happens when there is a MLDv2 querier in the network. The fix will only break out of the loop when there is a failure adding a multicast address. The mdb before the patch: dev ovirtmgmt port vnet0 grp ff02::1:ff7d:6603 temp dev ovirtmgmt port vnet1 grp ff02::1:ff7d:6604 temp dev ovirtmgmt port bond0.86 grp ff02::2 temp After the patch: dev ovirtmgmt port vnet0 grp ff02::1:ff7d:6603 temp dev ovirtmgmt port vnet1 grp ff02::1:ff7d:6604 temp dev ovirtmgmt port bond0.86 grp ff02::fb temp dev ovirtmgmt port bond0.86 grp ff02::2 temp dev ovirtmgmt port bond0.86 grp ff02::d temp dev ovirtmgmt port vnet0 grp ff02::1:ff00:76 temp dev ovirtmgmt port bond0.86 grp ff02::16 temp dev ovirtmgmt port vnet1 grp ff02::1:ff00:77 temp dev ovirtmgmt port bond0.86 grp ff02::1:ff00:def temp dev ovirtmgmt port bond0.86 grp ff02::1:ffa1:40bf temp Fixes: 08b202b6 ("bridge br_multicast: IPv6 MLD support.") Reported-by:
Rik Theys <Rik.Theys@esat.kuleuven.be> Signed-off-by:
Thadeu Lima de Souza Cascardo <cascardo@redhat.com> Tested-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Bjørn Mork authored
commit 44f6731d upstream. The tx_curr_frame_payload field is u32. When we try to calculate a small negative delta based on it, we end up with a positive integer close to 2^32 instead. So the tx_bytes pointer increases by about 2^32 for every transmitted frame. Fix by calculating the delta as a signed long. Cc: Ben Hutchings <ben.hutchings@codethink.co.uk> Reported-by:
Florian Bruhin <me@the-compiler.org> Fixes: 7a1e890e ("usbnet: Fix tx_bytes statistic running backward in cdc_ncm") Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Eric W. Biederman authored
commit 381c759d upstream. ip_error does not check if in_dev is NULL before dereferencing it. IThe following sequence of calls is possible: CPU A CPU B ip_rcv_finish ip_route_input_noref() ip_route_input_slow() inetdev_destroy() dst_input() With the result that a network device can be destroyed while processing an input packet. A crash was triggered with only unicast packets in flight, and forwarding enabled on the only network device. The error condition was created by the removal of the network device. As such it is likely the that error code was -EHOSTUNREACH, and the action taken by ip_error (if in_dev had been accessible) would have been to not increment any counters and to have tried and likely failed to send an icmp error as the network device is going away. Therefore handle this weird case by just dropping the packet if !in_dev. It will result in dropping the packet sooner, and will not result in an actual change of behavior. Fixes: 251da413 ("ipv4: Cache ip_error() routes even when not forwarding.") Reported-by:
Vittorio Gambaletta <linuxbugs@vittgam.net> Tested-by:
"Eric W. Biederman" <ebiederm@xmission.com> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Michal Kubeček authored
commit 27596472 upstream. When replacing an IPv6 multipath route with "ip route replace", i.e. NLM_F_CREATE | NLM_F_REPLACE, fib6_add_rt2node() replaces only first matching route without fixing its siblings, resulting in corrupted siblings linked list; removing one of the siblings can then end in an infinite loop. IPv6 ECMP implementation is a bit different from IPv4 so that route replacement cannot work in exactly the same way. This should be a reasonable approximation: 1. If the new route is ECMP-able and there is a matching ECMP-able one already, replace it and all its siblings (if any). 2. If the new route is ECMP-able and no matching ECMP-able route exists, replace first matching non-ECMP-able (if any) or just add the new one. 3. If the new route is not ECMP-able, replace first matching non-ECMP-able route (if any) or add the new route. We also need to remove the NLM_F_REPLACE flag after replacing old route(s) by first nexthop of an ECMP route so that each subsequent nexthop does not replace previous one. Fixes: 51ebd318 ("ipv6: add support of equal cost multipath (ECMP)") Signed-off-by:
Michal Kubecek <mkubecek@suse.cz> Acked-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
-
Michal Kubeček authored
commit 35f1b4e9 upstream. If adding a nexthop of an IPv6 multipath route fails, comment in ip6_route_multipath() says we are going to delete all nexthops already added. However, current implementation deletes even the routes it hasn't even tried to add yet. For example, running ip route add 1234:5678::/64 \ nexthop via fe80::aa dev dummy1 \ nexthop via fe80::bb dev dummy1 \ nexthop via fe80::cc dev dummy1 twice results in removing all routes first command added. Limit the second (delete) run to nexthops that succeeded in the first (add) run. Fixes: 51ebd318 ("ipv6: add support of equal cost multipath (ECMP)") Signed-off-by:
-
Florent Fourcot authored
commit 21858cd0 upstream. commit 1d13a96c ("ipv6: tcp: fix flowlabel value in ACK messages send from TIME_WAIT") added the flow label in the last TCP packets. Unfortunately, it was not casted properly. This patch replace the buggy shift with be32_to_cpu/cpu_to_be32. Fixes: 1d13a96c ("ipv6: tcp: fix flowlabel value in ACK messages") Reported-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
Florent Fourcot <florent.fourcot@enst-bretagne.fr> Acked-by:
-
Tommi Rantala authored
commit f30bf2a5 upstream. Fix memory leak introduced in commit a0840e2e ("IPVS: netns, ip_vs_ctl local vars moved to ipvs struct."): unreferenced object 0xffff88005785b800 (size 2048): comm "(-localed)", pid 1434, jiffies 4294755650 (age 1421.089s) hex dump (first 32 bytes): bb 89 0b 83 ff ff ff ff b0 78 f0 4e 00 88 ff ff .........x.N.... 04 00 00 00 a4 01 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<ffffffff8262ea8e>] kmemleak_alloc+0x4e/0xb0 [<ffffffff811fba74>] __kmalloc_track_caller+0x244/0x430 [<ffffffff811b88a0>] kmemdup+0x20/0x50 [<ffffffff823276b7>] ip_vs_control_net_init+0x1f7/0x510 [<ffffffff8231d630>] __ip_vs_init+0x100/0x250 [<ffffffff822363a1>] ops_init+0x41/0x190 [<ffffffff82236583>] setup_net+0x93/0x150 [<ffffffff82236cc2>] copy_net_ns+0x82/0x140 [<ffffffff810ab13d>] create_new_namespaces+0xfd/0x190 [<ffffffff810ab49a>] unshare_nsproxy_namespaces+0x5a/0xc0 [<ffffffff810833e3>] SyS_unshare+0x173/0x310 [<ffffffff8265cbd7>] system_call_fastpath+0x12/0x6f [<ffffffffffffffff>] 0xffffffffffffffff Fixes: a0840e2e ("IPVS: netns, ip_vs_ctl local vars moved to ipvs struct.") Signed-off-by:
Tommi Rantala <tt.rantala@gmail.com> Acked-by:
Julian Anastasov <ja@ssi.bg> Signed-off-by:
Simon Horman <horms@verge.net.au> Signed-off-by:
-
Harald Freudenberger authored
commit a1cae34e upstream. Multitheaded tests showed that the icv buffer in the current ghash implementation is not handled correctly. A move of this working ghash buffer value to the descriptor context fixed this. Code is tested and verified with an multithreaded application via af_alg interface. Signed-off-by:
Harald Freudenberger <freude@linux.vnet.ibm.com> Signed-off-by:
Gerald Schaefer <geraldsc@linux.vnet.ibm.com> Reported-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Ilya Dryomov authored
commit b0494532 upstream. This commit does two things. First, if there are any homeless lingering requests, we now request a new osdmap even if the osdmap that is being processed brought no changes, i.e. if a given lingering request turned homeless in one of the previous epochs and remained homeless in the current epoch. Not doing so leaves us with a stale osdmap and as a result we may miss our window for reestablishing the watch and lose notifies. MON=1 OSD=1: # cat linger-needmap.sh #!/bin/bash rbd create --size 1 test DEV=$(rbd map test) ceph osd out 0 rbd map dne/dne # obtain a new osdmap as a side effect (!) sleep 1 ceph osd in 0 rbd resize --size 2 test # rbd info test | grep size -> 2M # blockdev --getsize $DEV -> 1M N.B.: Not obtaining a new osdmap in between "osd out" and "osd in" above is enough to make it miss that resize notify, but that is a bug^Wlimitation of ceph watch/notify v1. Second, homeless lingering requests are now kicked just like those lingering requests whose mapping has changed. This is mainly to recognize that a homeless lingering request makes no sense and to preserve the invariant that a registered lingering request is not sitting on any of r_req_lru_item lists. This spares us a WARN_ON, which commit ba9d114e ("libceph: clear r_req_lru_item in __unregister_linger_request()") tried to fix the _wrong_ way. Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Reviewed-by:
Sage Weil <sage@redhat.com> Signed-off-by:
-
David Vrabel authored
commit 77bb3dfd upstream. A non-percpu VIRQ (e.g., VIRQ_CONSOLE) may be freed on a different VCPU than it is bound to. This can result in a race between handle_percpu_irq() and removing the action in __free_irq() because handle_percpu_irq() does not take desc->lock. The interrupt handler sees a NULL action and oopses. Only use the percpu chip/handler for per-CPU VIRQs (like VIRQ_TIMER). # cat /proc/interrupts | grep virq 40: 87246 0 xen-percpu-virq timer0 44: 0 0 xen-percpu-virq debug0 47: 0 20995 xen-percpu-virq timer1 51: 0 0 xen-percpu-virq debug1 69: 0 0 xen-dyn-virq xen-pcpu 74: 0 0 xen-dyn-virq mce 75: 29 0 xen-dyn-virq hvc_console Signed-off-by:
David Vrabel <david.vrabel@citrix.com> Signed-off-by:
-
Mark Hounschell authored
commit 74856fbf upstream. 256 bytes per sector support has been broken since 2.6.X, and no-one stepped up to fix this. So disable support for it. Signed-off-by:
Mark Hounschell <dmarkh@cfl.rr.com> Signed-off-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
James Bottomley <JBottomley@Odin.com> Signed-off-by:
-
Ludovic Desroches authored
commit 60c8f783 upstream. clkdiv is declared as an u32 but it can be set to a negative value causing a huge divisor value. Change its type to int to avoid this case. Signed-off-by:
Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Ansgar Hegerfeld authored
commit 09ea9976 upstream. The Lenovo ThinkPad L450 requires the ALC292_FIXUP_TPT440_DOCK fix in order to get sound output on the docking stations audio port. This patch was tested using a ThinkPad L450 (20DSS00B00) using kernel 4.0.3 and a ThinkPad Pro Dock. Signed-off-by:
Ansgar Hegerfeld <linux@hegerfeld.org> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
David Henningsson authored
commit 6ffc0898 upstream. This patch adds support for Conexant HD Audio codecs CX20721, CX20722, CX20723 and CX20724. BugLink: https://bugs.launchpad.net/bugs/1454656Signed-off-by:
David Henningsson <david.henningsson@canonical.com> Signed-off-by:
-
Anton Blanchard authored
commit 5e95235c upstream. Recent toolchains force the TOC to be 256 byte aligned. We need to enforce this alignment in our linker script, otherwise pointers to our TOC variables (__toc_start, __prom_init_toc_start) could be incorrect. If they are bad, we die a few hundred instructions into boot. Signed-off-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Benjamin Tissoires authored
commit 3c0213d1 upstream. When the v3 hardware sees more than one finger, it uses the semi-mt protocol to report the touches. However, it currently works when num_fingers is 0, 1 or 2, but when it is 3 and above, it sends only 1 finger as if num_fingers was 1. This confuses userspace which knows how to deal with extra fingers when all the slots are used, but not when some are missing. Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=90101Signed-off-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Zidan Wang authored
commit 17fc2e0a upstream. According to the RM of wm8958, BCLK DIV 348 doesn't exist, correct it to 384. Signed-off-by:
Zidan Wang <zidan.wang@freescale.com> Acked-by:
Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Zidan Wang authored
commit 85e36a1f upstream. It should be "RINPUT3" instead of "LINPUT3" route to "Right Input Mixer". Signed-off-by:
-
K. Y. Srinivasan authored
commit dc45708c upstream. Set the SRB flags correctly when there is no data transfer. Without this change some IHV drivers will fail valid commands such as TEST_UNIT_READY. Signed-off-by:
K. Y. Srinivasan <kys@microsoft.com> Reviewed-by:
Long Li <longli@microsoft.com> Signed-off-by:
-
Xiao Guangrong authored
commit 0be0226f upstream. KVM may turn a user page to a kernel page when kernel writes a readonly user page if CR0.WP = 1. This shadow page entry will be reused after SMAP is enabled so that kernel is allowed to access this user page Fix it by setting SMAP && !CR0.WP into shadow page's role and reset mmu once CR4.SMAP is updated Signed-off-by:
Xiao Guangrong <guangrong.xiao@linux.intel.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
-
Paolo Bonzini authored
commit 89876115 upstream. smep_andnot_wp is initialized in kvm_init_shadow_mmu and shadow pages should not be reused for different values of it. Thus, it has to be added to the mask in kvm_mmu_pte_write. Reviewed-by:
-
Xiao Guangrong authored
commit 7cbeed9b upstream. Current permission check assumes that RSVD bit in PFEC is always zero, however, it is not true since MMIO #PF will use it to quickly identify MMIO access Fix it by clearing the bit if walking guest page table is needed Signed-off-by:
-
Janusz Dziedzic authored
commit 47b4e1fc upstream. Remove checking tailroom when adding IV as it uses only headroom, and move the check to the ICV generation that actually needs the tailroom. In other case I hit such warning and datapath don't work, when testing: - IBSS + WEP - ath9k with hw crypt enabled - IPv6 data (ping6) WARNING: CPU: 3 PID: 13301 at net/mac80211/wep.c:102 ieee80211_wep_add_iv+0x129/0x190 [mac80211]() [...] Call Trace: [<ffffffff817bf491>] dump_stack+0x45/0x57 [<ffffffff8107746a>] warn_slowpath_common+0x8a/0xc0 [<ffffffff8107755a>] warn_slowpath_null+0x1a/0x20 [<ffffffffc09ae109>] ieee80211_wep_add_iv+0x129/0x190 [mac80211] [<ffffffffc09ae7ab>] ieee80211_crypto_wep_encrypt+0x6b/0xd0 [mac80211] [<ffffffffc09d3fb1>] invoke_tx_handlers+0xc51/0xf30 [mac80211] [...] Signed-off-by:
Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Nadav Haklai authored
commit efa86858 upstream. Improve the Armada 380 thermal sensor accuracy by using updated formula. The updated formula is: Temperature[C degrees] = 0.4761 * tsen_vsen_out - 279.1 Signed-off-by:
Nadav Haklai <nadavh@marvell.com> Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
Eduardo Valentin <edubezval@gmail.com> Signed-off-by:
-
Axel Lin authored
commit 545774bd upstream. mc13xxx_reg_rmw() won't change any bit if passing 0 to the mask field. Pass AUDIO_SSI_SEL instead of 0 for the mask field to set AUDIO_SSI_SEL bit. Signed-off-by:
Axel Lin <axel.lin@ingics.com> Signed-off-by:
-
Takashi Iwai authored
commit 88776f36 upstream. Fujitsu Lifebook E752 laptop needs a similar quirk done for Lifebook T731. Otherwise the headphone is always muted. Reported-and-tested-by:
Christian Weber <we_chris@hotmail.com> Signed-off-by:
-
Junling Zheng authored
Based on 08adb7da upstream. Commit 281c9c36 (net: compat: Update get_compat_msghdr() to match copy_msghdr_from_user() behaviour) made get_compat_msghdr() return error if msg_sys->msg_namelen was negative, which changed the behaviors of recvmsg and sendmsg syscall in a lib32 system: Before commit 281c9c36, get_compat_msghdr() wouldn't fail and it would return -EINVAL in move_addr_to_user() or somewhere if msg_sys->msg_namelen was invalid and then syscall returned -EINVAL, which is correct. And now, when msg_sys->msg_namelen is negative, get_compat_msghdr() will fail and wants to return -EINVAL, however, the outer syscall will return -EFAULT directly, which is unexpected. This patch gets the return value of get_compat_msghdr() as well as copy_msghdr_from_user(), then returns this expected value if get_compat_msghdr() fails. Fixes: 281c9c36 (net: compat: Update get_compat_msghdr() to match copy_msghdr_from_user() behaviour) Signed-off-by:
Junling Zheng <zhengjunling@huawei.com> Signed-off-by:
Hanbing Xu <xuhanbing@huawei.com> Cc: Li Zefan <lizefan@huawei.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: David Miller <davem@davemloft.net> Signed-off-by:
-
- 28 May, 2015 13 commits
-
-
Thomas Petazzoni authored
This patch is a partial backport of commit ef01c6c3 ("ARM: mvebu: remove Armada 375 Z1 workaround for I/O coherency"). This commit was merged in v3.19, so kernel versions later than v3.19 are not affected by the problem that this commit fixes. It does not make a lot of sense to backport this commit entirely, since it is mainly removing some no longer useful code. However, this commit is also making sure that the bus_register_notifier that register the custom DMA operations that should be used for HW I/O coherency does not get registered when said HW I/O coherency is not enabled. This is particularly critical since we have decided to disable HW I/O coherency completely in all kernels < 4.0, to be on the safe side, while experimenting a new implementation of the HW I/O coherency in >= 4.0. Without this commit, kernels earlier than 3.18 have the custom DMA operations normally used for HW I/O coherency registered (they don't do cache maintenance operations), while HW I/O coherency is disabled. It essentially causes every DMA transfer to transfer garbage. The issue fixed by this commit was introduced by 5ab5afd8 ("ARM: mvebu: implement Armada 375 coherency workaround"), but it was not visible until now since it didn't cause any problem when HW I/O coherency is enabled. Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Chen Gang authored
commit 9493c242 upstream. Remove 2 redundant extern inline functions: qla8044_set_qsnt_ready() and qla8044_need_reset_handler(). At present, within upstream next kernel source code, they are only used within "drivers/scsi/qla2xxx/qla_nx2.c". The related error and warnings (with allmodconfig under tile): CC [M] drivers/scsi/qla2xxx/qla_nx2.o drivers/scsi/qla2xxx/qla_nx2.c:1633:1: error: static declaration of 'qla8044_need_reset_handler' follows non-static declaration qla8044_need_reset_handler(struct scsi_qla_host *vha) ^ In file included from drivers/scsi/qla2xxx/qla_def.h:3706:0, from drivers/scsi/qla2xxx/qla_nx2.c:11: drivers/scsi/qla2xxx/qla_gbl.h:756:20: note: previous declaration of 'qla8044_need_reset_handler' was here extern inline void qla8044_need_reset_handler(struct scsi_qla_host *vha); ^ drivers/scsi/qla2xxx/qla_gbl.h:756:20: warning: inline function 'qla8044_need_reset_handler' declared but never defined make[3]: *** [drivers/scsi/qla2xxx/qla_nx2.o] Error 1 make[2]: *** [drivers/scsi/qla2xxx] Error 2 make[1]: *** [drivers/scsi] Error 2 make: *** [drivers] Error 2 CC [M] drivers/scsi/qla2xxx/qla_tmpl.o In file included from drivers/scsi/qla2xxx/qla_def.h:3706:0, from drivers/scsi/qla2xxx/qla_tmpl.c:7: drivers/scsi/qla2xxx/qla_gbl.h:755:20: warning: inline function 'qla8044_set_qsnt_ready' declared but never defined extern inline void qla8044_set_qsnt_ready(struct scsi_qla_host *vha); ^ Signed-off-by:
Chen Gang <gang.chen.5i5j@gmail.com> Acked-by:
Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by:
Christoph Hellwig <hch@lst.de> Cc: Philip Müller <philm@manjaro.org> Signed-off-by:
-
Arnd Bergmann authored
commit 0c9f3a65 upstream. The rtl8712 driver has an 'extern inline' function that contains an 'if', which causes lots of warnings with CONFIG_PROFILE_ALL_BRANCHES overriding the definition of 'if': drivers/staging/rtl8712/ieee80211.h:759:229: warning: '______f' is static but declared in inline function 'ieee80211_get_hdrlen' which is not static [enabled by default] This changes the driver to use 'static inline' instead, which happens to be the correct annotation anyway. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: Florian Schilhabel <florian.c.schilhabel@googlemail.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Philip Müller <philm@manjaro.org> Signed-off-by:
-
gregkh@linuxfoundation.org authored
Patch not upstream as this driver is deleted there. Fix up some "extern inline" functions as they break the build when using a "modern" complier (i.e. gcc5). Signed-off-by:
-
Behan Webster authored
commit 62ec95f8 upstream. rtllib_probe_req is defined as "static inline" in rtllib_softmac.c however it is declared differently as "extern inline" in rtllib_softmac.h. Since it isn't used outside of the scope of rtllib_softmac, it makes sense to remove the incorrect declaration. Signed-off-by:
Behan Webster <behanw@converseincode.com> Suggested-by:
-
Kirill A. Shutemov authored
commit 51b97e35 upstream. Sasha Levin reports: "gcc5 changes the default standard to c11, which makes kernel build unhappy Explicitly define the kernel standard to be gnu89 which should keep everything working exactly like it was before gcc5" There are multiple small issues with the new default, but the biggest issue seems to be that the old - and very useful - GNU extension to allow a cast in front of an initializer has gone away. Patch updated by Kirill: "I'm pretty sure all gcc versions you can build kernel with supports -std=gnu89. cc-option is redunrant. We also need to adjust HOSTCFLAGS otherwise allmodconfig fails for me" Note by Andrew Pinski: "Yes it was reported and both problems relating to this extension has been added to gnu99 and gnu11. Though there are other issues with the kernel dealing with extern inline have different semantics between gnu89 and gnu99/11" End result: we may be able to move up to a newer stdc model eventually, but right now the newer models have some annoying deficiencies, so the traditional "gnu89" model ends up being the preferred one. Signed-off-by:
Sasha Levin <sasha.levin@oracle.com> Singed-off-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Cc: Philip Müller <philm@manjaro.org> Signed-off-by:
-
Behan Webster authored
commit 6d91857d upstream. With compilers which follow the C99 standard (like modern versions of gcc and clang), "extern inline" does the opposite thing from older versions of gcc (emits code for an externally linkable version of the inline function). "static inline" does the intended behavior in all cases instead. Signed-off-by:
-
Konrad Rzeszutek Wilk authored
commit a6dfa128 upstream. A huge amount of NIC drivers use the DMA API, however if compiled under 32-bit an very important part of the DMA API can be ommitted leading to the drivers not working at all (especially if used with 'swiotlb=force iommu=soft'). As Prashant Sreedharan explains it: "the driver [tg3] uses DEFINE_DMA_UNMAP_ADDR(), dma_unmap_addr_set() to keep a copy of the dma "mapping" and dma_unmap_addr() to get the "mapping" value. On most of the platforms this is a no-op, but ... with "iommu=soft and swiotlb=force" this house keeping is required, ... otherwise we pass 0 while calling pci_unmap_/pci_dma_sync_ instead of the DMA address." As such enable this even when using 32-bit kernels. Reported-by:
Ian Jackson <Ian.Jackson@eu.citrix.com> Signed-off-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by:
Prashant Sreedharan <prashant@broadcom.com> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Michael Chan <mchan@broadcom.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: boris.ostrovsky@oracle.com Cc: cascardo@linux.vnet.ibm.com Cc: david.vrabel@citrix.com Cc: sanjeevb@broadcom.com Cc: siva.kallam@broadcom.com Cc: vyasevich@gmail.com Cc: xen-devel@lists.xensource.com Link: http://lkml.kernel.org/r/20150417190448.GA9462@l.oracle.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Mark Rutland authored
commit c0978773 upstream. arm64 builds with GCC 5 have caused the __asmeq assertions in the PSCI calling code to fire, so move the ARM PSCI calls out of line into their own assembly file for consistency and to safeguard against the same issue occuring with the 32-bit toolchain. [will: brought into line with arm64 implementation] Reported-by:
Andy Whitcroft <apw@canonical.com> Signed-off-by:
Mark Rutland <mark.rutland@arm.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Alexey Khoroshilov authored
commit bc26d4d0 upstream. A deadlock can be initiated by userspace via ioctl(SNDCTL_SEQ_OUTOFBAND) on /dev/sequencer with TMR_ECHO midi event. In this case the control flow is: sound_ioctl() -> case SND_DEV_SEQ: case SND_DEV_SEQ2: sequencer_ioctl() -> case SNDCTL_SEQ_OUTOFBAND: spin_lock_irqsave(&lock,flags); play_event(); -> case EV_TIMING: seq_timing_event() -> case TMR_ECHO: seq_copy_to_input() -> spin_lock_irqsave(&lock,flags); It seems that spin_lock_irqsave() around play_event() is not necessary, because the only other call location in seq_startplay() makes the call without acquiring spinlock. So, the patch just removes spinlocks around play_event(). By the way, it removes unreachable code in seq_timing_event(), since (seq_mode == SEQ_2) case is handled in the beginning. Compile tested only. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by:
-
Dean Nelson authored
commit 2cff98b9 upstream. __dma_alloc() does a PAGE_ALIGN() on the passed in size argument before doing anything else. __dma_free() does not. And because it doesn't, it is possible to leak memory should size not be an integer multiple of PAGE_SIZE. The solution is to add a PAGE_ALIGN() to __dma_free() like is done in __dma_alloc(). Additionally, this patch removes a redundant PAGE_ALIGN() from __dma_alloc_coherent(), since __dma_alloc_coherent() can only be called from __dma_alloc(), which already does a PAGE_ALIGN() before the call. Acked-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
Dean Nelson <dnelson@redhat.com> Signed-off-by:
-
Hans Ulli Kroll authored
commit 31fc835f upstream. This patch fixes a compiler warning in gemini_restart() issued by commit 7b6d864b ("reboot:arm: reboot_mode changes from char to enum reboot_mode"). arch/arm/mach-gemini/board-rut1xx.c:93:2: warning: initialization from incompatible pointer type The warning is harmless, and the patch does not need to be backported to stable kernels. Fixes: 7b6d864b ("reboot:arm: reboot_mode changes from char to enum reboot_mode.") Signed-off-by:
Hans Ulli Kroll <ulli.kroll@googlemail.com> Signed-off-by:
-
Toshiaki Makita authored
commit 2439fc4d upstream. adapter->tx_ring is set to NULL where rx_ring should be. Fixes: 5536d210 ("igb: Combine q_vector and ring allocation into a single function") Signed-off-by:
Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
