- 02 Dec, 2017 31 commits
-
-
Peter Meerwald-Stadler authored
Current code assumes always 2 measurements (6 bytes) have to be copied, prepare for more flexibility Signed-off-by:
Peter Meerwald-Stadler <pmeerw@pmeerw.net> Acked-by:
Matt Ranostay <matt.ranostay@konsulko.com> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Peter Meerwald-Stadler authored
Move the programming of the mode setting from init() to buffer_postenable() Split out a separate function to only update the power/shutdown bit This changes permits to more easily implement different modes of measurements in further patches Signed-off-by:
-
Peter Meerwald-Stadler authored
Signed-off-by:
-
Peter Meerwald-Stadler authored
Chip must not be in shutdown for reading temperature, so briefly leave shutdown if buffer is not already running Signed-off-by:
-
Peter Meerwald-Stadler authored
Signed-off-by:
-
Peter Meerwald-Stadler authored
Signed-off-by:
-
Peter Meerwald-Stadler authored
Signed-off-by:
-
Peter Meerwald-Stadler authored
Table 4 of the datasheet specifies the mode control, these are not individual bits; add multi LED mode Add multi-LED mode and fix MODE_MASK (3 bits wide, not 2) Signed-off-by:
-
Peter Meerwald-Stadler authored
Signed-off-by:
-
Peter Meerwald-Stadler authored
Signed-off-by:
-
Fabrice Gasnier authored
STM32H7 ADC channels can be configured either as single ended or differential with 'st,adc-channels' or 'st,adc-diff-channels' (positive and negative input pair: <vinp vinn>, ...). Differential channels have different offset and scale, from spec: raw value = (full_scale / 2) * (1 + (vinp - vinn) / vref). Add offset attribute. Differential channels are selected by DIFSEL register. Negative inputs must be added to pre-selected channels as well (PCSEL). Signed-off-by:
Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by:
-
Fabrice Gasnier authored
Remove const array that defines channels. Build channels definition at probe time, when initializing channels (only for requested ones). This will ease adding differential channels support. Signed-off-by:
-
Fabrice Gasnier authored
STM32H7 ADC channels may be configured either as single-ended or differential. Add 'st,adc-diff-channels' property to support differential channels. Differential channels are defined as a pair of positive and negative inputs: vinp & vinn. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Stefan Brüns authored
Reducing shunt and bus voltage range improves the accuracy, so allow altering the default settings. Both settings are exposed as gain values. While for the shunt voltage this is straightforward, the bus range settings of 32V (default) and 16V are mapped to gain values of 1 resp. 2, to provide a uniform API to userspace. As the gain settings are incorporated into the raw values by the sensor itself, adjusting of the scale attributes is not necessary. Signed-off-by:
Stefan Brüns <stefan.bruens@rwth-aachen.de> Signed-off-by:
-
Stefan Brüns authored
While the config uses the physical value corresponding to the LSB for both the power and the bus voltage register, the shunt voltage is specified as parts of 1 mV. Use the LSB physical value for all registers. No functional change. Signed-off-by:
-
Stefan Brüns authored
Lower bits of the INA219/220 bus voltage register are conversion status flags, properly shift the value. When reading via IIO buffer, the value is passed on unaltered, shifting is the responsibility of the user. Signed-off-by:
-
Andy Shevchenko authored
Since i2c_unregister_device() became NULL-aware we may remove duplicate NULL check. Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: linux-iio@vger.kernel.org Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Markus Elfring authored
* Add a jump target so that a call of the function "mutex_unlock" is stored only twice in this function implementation. * Replace two calls by goto statements. This issue was detected by using the Coccinelle software. Signed-off-by:
Markus Elfring <elfring@users.sourceforge.net> Signed-off-by:
-
Markus Elfring authored
* Add a jump target so that a call of the function "mutex_unlock" is stored only twice in this function implementation. * Replace two calls by goto statements. This issue was detected by using the Coccinelle software. Signed-off-by:
-
Andy Shevchenko authored
Add new ACPI ID for ak9911 as had been found on prototype board. Signed-off-by:
-
Andy Shevchenko authored
Add new ACPI ID for sx9500 as had been found on prototype board. Signed-off-by:
-
Harinath Nampally authored
Rename structs holding event configuration registers to more appropriate names. This naming is consistent with the event config register names given in the mma845x and fxls8471 datasheets. Signed-off-by:
Harinath Nampally <harinath922@gmail.com> Acked-by:
Martin Kepplinger <martink@posteo.de> Signed-off-by:
-
Harinath Nampally authored
Rename time step look up struct to generic name as the values in the look table are same for all the other events like pulse, transient etc. Signed-off-by:
-
Peter Meerwald-Stadler authored
Signed-off-by:
-
Peter Meerwald-Stadler authored
Driver for 20-bit ALS and UV B sensor with I2C interface exposing the following API: in_uvindex_input in_illuminance_raw in_illuminance_scale in_illuminance_scale_available in_intensity_uv_raw in_intensity_uv_scale in_intensity_uv_scale_available integration_time integration_time_available Signed-off-by:
-
Gustavo A. R. Silva authored
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. Addresses-Coverity-ID: 1397962 Signed-off-by:
Gustavo A. R. Silva <garsilva@embeddedor.com> Signed-off-by:
-
Paolo Cretaro authored
Fix gcc warnings about variable 'ec_device' being set but not used in these files: common/cros_ec_sensors/cros_ec_sensors.c:194:25 light/cros_ec_light_prox.c:184:25 Signed-off-by:
Paolo Cretaro <paolocretaro@gmail.com> Signed-off-by:
-
Eugen Hristev authored
Need to acknowledge DRDY irq in direct mode/ software triggered mode. Otherwise, on the next conversion, overrun flag will be raised, which is not a correct state. This doesn't affect the functionality, but will generate possible incorrect overrun reports. Signed-off-by:
Eugen Hristev <eugen.hristev@microchip.com> Signed-off-by:
-
Eugen Hristev authored
Added support for DMA transfers. The implementation uses the user watermark to decide whether DMA will be used or not. For watermark 1, DMA will not be used. If watermark is bigger, DMA will be used. Sysfs attributes are created to indicate whether the DMA is used, with hwfifo_enabled, and the current DMA watermark is readable in hwfifo_watermark. Minimum and maximum values are in hwfifo_watermark_min and hwfifo_watermark_max. Signed-off-by:
-
Eugen Hristev authored
Added property for DMA configuration of the device. Signed-off-by:
-
Linus Walleij authored
The module license checker complains about these two so just fix it up. They are both GPLv2, both written by me or using code I extracted while refactoring from the GPLv2 drivers. Cc: Randy Dunlap <rdunlap@infradead.org> Reported-by:
Randy Dunlap <rdunlap@infradead.org> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
- 30 Nov, 2017 1 commit
-
-
Randy Dunlap authored
IPX depends on NET, so add that to the Kconfig file. Fixes Kconfig warning and build errors: warning: (IPX) selects LLC which has unmet direct dependencies (NET) and 94 "undefined reference" build errors. Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 28 Nov, 2017 8 commits
-
-
Benjamin Gaignard authored
Put include in alphabetic order Signed-off-by:
Benjamin Gaignard <benjamin.gaignard@linaro.org> Acked-by:
Laura Abbott <labbott@redhat.com> Signed-off-by:
-
Arvind Yadav authored
All attribute group created during sys_init_dir() should be removed in sys_free_dir() Signed-off-by:
Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by:
-
Tim Sell authored
Add necessary casting to several places where we were doing 32-bit arithmetic (unsigned) to produce a 64-bit (unsigned long) result, to prevent the theoretical possibility of a 32-bit overflow during the arithmetic. FYI, these are unsigned long: ctx->param_bytes ctx->allocbytes These are unsigned int: bytes phdr->name_offset phdr->name_length Here is the test program demonstrating why we really need the casts: void main() { unsigned int i; unsigned long il; printf("sizeof(int) =%dn",sizeof(i)); printf("sizeof(long)=%dn",sizeof(il)); i = (unsigned int)((((unsigned long)(1)) << 32) - 1); printf("i = %un", i); il = i+1; printf("adding 1 withOUT cast = %lun", il); il = (unsigned long)i+1; printf("adding 1 WITH cast = %lun", il); } [selltc@mac tmp]$ gcc x.c -o x.out [selltc@mac tmp]$ ./x.out sizeof(int) =4 sizeof(long)=8 i = 4294967295 adding 1 withOUT cast = 0 adding 1 WITH cast = 4294967296 Signed-off-by:Tim Sell <Timothy.Sell@unisys.com> Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
David Kershner <david.kershner@unisys.com> Reviewed-by:
David Binder <david.binder@unisys.com> Signed-off-by:
-
Sinan Kaya authored
Remove unused rtsx_read_pci_cfg_byte() function. Signed-off-by:
Sinan Kaya <okaya@codeaurora.org> Signed-off-by:
-
Kees Cook authored
Noticed during Clang builds. This drops the redundant parentheses. Cc: Samuel Ortiz <samuel@sortiz.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: devel@driverdev.osuosl.org Signed-off-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
-
Colin Ian King authored
dev_alloc_skb can potentially return NULL, so add a null check to avoid a null pointer dereference on skb Detected by CoverityScan, CID#1454558 ("Dereference on null return") Fixes: 7e5b796c ("staging: r8822be: Add the driver code") Signed-off-by:Colin Ian King <colin.king@canonical.com> Acked-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Talat Batheesh authored
This patch fix the line over 80 characters warning that was detected using checkpatch.pl script. Signed-off-by:
Talat Batheesh <talat.b87@gmail.com> Signed-off-by:
-
Arvind Yadav authored
All attribute group created during class_procfs_init() should be removed. if class_procfs_init() will fail and also in class_procfs_clean(). Signed-off-by:
-
