- 02 Mar, 2023 1 commit
-
-
Sergio Paracuellos authored
MT7621 SoC provides a system controller node for accessing to some registers. Add a phandle in this node to avoid using MIPS related arch operations and includes in watchdog driver code. Acked-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
Sergio Paracuellos <sergio.paracuellos@gmail.com> Reviewed-by:
Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20230214103936.1061078-2-sergio.paracuellos@gmail.comSigned-off-by:
Wim Van Sebroeck <wim@linux-watchdog.org>
-
- 18 Feb, 2023 27 commits
-
-
George Cherian authored
Make sure to honour the max_hw_heartbeat_ms while programming the timeout value to WOR. Clamp the timeout passed to sbsa_gwdt_set_timeout() to make sure the programmed value is within the permissible range. Fixes: abd3ac79 ("watchdog: sbsa: Support architecture version 1") Signed-off-by:
George Cherian <george.cherian@marvell.com> Reviewed-by:
-
Bartosz Golaszewski authored
Add a compatible for the sa8775p platform's KPSS watchdog. Signed-off-by:
Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Acked-by:
-
Thomas Weißschuh authored
This synchronizes the information reported by ioctl and sysfs. The mismatch is confusing because "wdctl" from util-linux uses the ioctl when used with root privileges and sysfs without. Signed-off-by:
Thomas Weißschuh <linux@weissschuh.net> Reviewed-by:
-
Thomas Weißschuh authored
This synchronizes the information reported by ioctl and sysfs. The mismatch is confusing because "wdctl" from util-linux uses the ioctl when used with root privileges and sysfs without. The file is called "fw_version" instead of "firmware_version" as "firmware_version" is already used as custom attribute by single drivers. Signed-off-by:
-
Andrej Picej authored
Property "fsl,suspend-in-wait" suspends watchdog in "WAIT" mode which corresponds to Linux's Suspend-to-Idle S0 mode. If this property is not set and the device is put into Suspend-to-Idle mode, the watchdog triggers a reset after 128 seconds. Signed-off-by:
Andrej Picej <andrej.picej@norik.com> Reviewed-by:
Fabio Estevam <festevam@gmail.com> Reviewed-by:
-
Andrej Picej authored
Putting device into the "Suspend-To-Idle" mode causes watchdog to trigger and resets the board after set watchdog timeout period elapses. Introduce new device-tree property "fsl,suspend-in-wait" which suspends watchdog in WAIT mode. This is done by setting WDW bit in WCR (Watchdog Control Register). Watchdog operation is restored after exiting WAIT mode as expected. WAIT mode corresponds with Linux's "Suspend-To-Idle". Signed-off-by:
-
Li Hua authored
The stack variable msb and lsb may be used uninitialized in function usb_pcwd_get_temperature and usb_pcwd_get_timeleft when usb card no response. The build waring is: drivers/watchdog/pcwd_usb.c:336:22: error: ‘lsb’ is used uninitialized in this function [-Werror=uninitialized] *temperature = (lsb * 9 / 5) + 32; ~~~~^~~ drivers/watchdog/pcwd_usb.c:328:21: note: ‘lsb’ was declared here unsigned char msb, lsb; ^~~ cc1: all warnings being treated as errors scripts/Makefile.build:250: recipe for target 'drivers/watchdog/pcwd_usb.o' failed make[3]: *** [drivers/watchdog/pcwd_usb.o] Error 1 Fixes: b7e04f8c ("mv watchdog tree under drivers") Signed-off-by:Li Hua <hucool.lihua@huawei.com> Reviewed-by:
-
Krzysztof Kozlowski authored
Merge Qualcomm MSM timer bindings into watchdog, because the timer compatibles are already included here and the hardware is quite similar. While converting the MSM timer bindings, adjust clock-frequency property to take only one frequency, instead of two, because: 1. DT schema does not allow to frequencies, 2. The Linux timer driver reads only first frequency. Signed-off-by:
Daniel Lezcano <daniel.lezcano@linaro.org> Reviewed-by:
Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20221212163532.142533-6-krzysztof.kozlowski@linaro.orgSigned-off-by:
-
Krzysztof Kozlowski authored
Both of type of watchdogs described in the binding (the KPSS watchdog and APSS WDT timer) have interrupts. Allow interrupts and describe them for KPSS watchdog to fix warnings like: watchdog@17c10000: Unevaluated properties are not allowed ('interrupts' was unexpected) Signed-off-by: -
Krzysztof Kozlowski authored
Document new MDM9615 qcom,kpss-wdt-mdm9615 watchdog/timer compatible. Signed-off-by:
-
Krzysztof Kozlowski authored
The MSM timer ("qcom,msm-timer") is a bit different timer and watchdog device than KPSS watchdog. It has its own generic and specific compatibles, so fix the list to reflect this. Adjust the example to show the newer KPSS watchdog. Signed-off-by: -
Krzysztof Kozlowski authored
The compatible "qcom,kpss-wdt" is too generic and should not be used alone. Mark it as deprecated when not prepended by specific compatible. Signed-off-by:
-
Krzysztof Kozlowski authored
The device specific compatibles ("qcom,kpss-wdt-ipq4019") should be follwed by fallback "qcom,kpss-wdt", which is actually used by Linux driver for binding. Signed-off-by: -
Chen Jun authored
kmemleak reports memory leaks in watchdog_dev_register, as follows: unreferenced object 0xffff888116233000 (size 2048): comm ""modprobe"", pid 28147, jiffies 4353426116 (age 61.741s) hex dump (first 32 bytes): 80 fa b9 05 81 88 ff ff 08 30 23 16 81 88 ff ff .........0#..... 08 30 23 16 81 88 ff ff 00 00 00 00 00 00 00 00 .0#............. backtrace: [<000000007f001ffd>] __kmem_cache_alloc_node+0x157/0x220 [<000000006a389304>] kmalloc_trace+0x21/0x110 [<000000008d640eea>] watchdog_dev_register+0x4e/0x780 [watchdog] [<0000000053c9f248>] __watchdog_register_device+0x4f0/0x680 [watchdog] [<00000000b2979824>] watchdog_register_device+0xd2/0x110 [watchdog] [<000000001f730178>] 0xffffffffc10880ae [<000000007a1a8bcc>] do_one_initcall+0xcb/0x4d0 [<00000000b98be325>] do_init_module+0x1ca/0x5f0 [<0000000046d08e7c>] load_module+0x6133/0x70f0 ... unreferenced object 0xffff888105b9fa80 (size 16): comm ""modprobe"", pid 28147, jiffies 4353426116 (age 61.741s) hex dump (first 16 bytes): 77 61 74 63 68 64 6f 67 31 00 b9 05 81 88 ff ff watchdog1....... backtrace: [<000000007f001ffd>] __kmem_cache_alloc_node+0x157/0x220 [<00000000486ab89b>] __kmalloc_node_track_caller+0x44/0x1b0 [<000000005a39aab0>] kvasprintf+0xb5/0x140 [<0000000024806f85>] kvasprintf_const+0x55/0x180 [<000000009276cb7f>] kobject_set_name_vargs+0x56/0x150 [<00000000a92e820b>] dev_set_name+0xab/0xe0 [<00000000cec812c6>] watchdog_dev_register+0x285/0x780 [watchdog] [<0000000053c9f248>] __watchdog_register_device+0x4f0/0x680 [watchdog] [<00000000b2979824>] watchdog_register_device+0xd2/0x110 [watchdog] [<000000001f730178>] 0xffffffffc10880ae [<000000007a1a8bcc>] do_one_initcall+0xcb/0x4d0 [<00000000b98be325>] do_init_module+0x1ca/0x5f0 [<0000000046d08e7c>] load_module+0x6133/0x70f0 ... The reason is that put_device is not be called if cdev_device_add fails and wdd->id != 0. watchdog_cdev_register wd_data = kzalloc [1] err = dev_set_name [2] .. err = cdev_device_add if (err) { if (wdd->id == 0) { // wdd->id != 0 .. } return err; // [1],[2] would be leaked To fix it, call put_device in all wdd->id cases. Fixes: 72139dfa ("watchdog: Fix the race between the release of watchdog_core_data and cdev") Signed-off-by:Chen Jun <chenjun102@huawei.com> Reviewed-by:
-
Christophe JAILLET authored
The kstrto<something>() functions have been moved from kernel.h to kstrtox.h. So, in order to eventually remove <linux/kernel.h> from <linux/watchdog.h>, include the latter directly in the appropriate files. Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by:
-
ruanjinjie authored
free_irq() is missing in case of error in at91_wdt_init(), use devm_request_irq to fix that. Fixes: 5161b31d ("watchdog: at91sam9_wdt: better watchdog support") Signed-off-by:
ruanjinjie <ruanjinjie@huawei.com> Reviewed-by:
-
Fabrizio Castro authored
As per section 48.4 of the HW User Manual, IPs in the RZ/V2M SoC need either a TYPE-A reset sequence or a TYPE-B reset sequence. More specifically, the watchdog IP needs a TYPE-B reset sequence. If the proper reset sequence isn't implemented, then resetting IPs may lead to undesired behaviour. In the restart callback of the watchdog driver the reset has basically no effect on the desired funcionality, as the register writes following the reset happen before the IP manages to come out of reset. Implement the TYPE-B reset sequence in the watchdog driver to address the issues with the restart callback on RZ/V2M. Fixes: ec122fd9 ("watchdog: rzg2l_wdt: Add rzv2m support") Signed-off-by:
Fabrizio Castro <fabrizio.castro.jz@renesas.com> Reviewed-by:
Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20221117114907.138583-3-fabrizio.castro.jz@renesas.comSigned-off-by:
-
Lad Prabhakar authored
On RZ/Five SoC it was observed that setting timeout (to say 1 sec) wouldn't reset the system. The procedure described in the HW manual (Procedure for Activating Modules) for activating the target module states we need to start supply of the clock module before applying the reset signal. This patch makes sure we follow the same procedure to clear the registers of the WDT module, fixing the issues seen on RZ/Five SoC. While at it re-used rzg2l_wdt_stop() in rzg2l_wdt_set_timeout() as it has the same function calls. Fixes: 4055ee81 ("watchdog: rzg2l_wdt: Add set_timeout callback") Signed-off-by:
Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by:
Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/r/20221117114907.138583-2-fabrizio.castro.jz@renesas.comSigned-off-by:
-
Konrad Dybcio authored
Document the MSM8994 watchdog timer which is already used in DT. Signed-off-by:
Konrad Dybcio <konrad.dybcio@linaro.org> Acked-by:
-
Lad Prabhakar authored
The WDT block on the RZ/Five SoC is identical to one found on the RZ/G2UL SoC. "renesas,r9a07g043-wdt" compatible string will be used on the RZ/Five SoC so to make this clear, update the comment to include RZ/Five SoC. No driver changes are required as generic compatible string "renesas,rzg2l-wdt" will be used as a fallback on RZ/Five SoC. Signed-off-by:
-
Neil Armstrong authored
Convert the Amlogic Meson6 SoCs Watchdog timer bindings to dt-schema. Take in account the used interrupts property. The "amlogic,meson8-wdt" representation has been simplified since there's no users of this compatible used along the "amlogic,meson6-wdt". Reviewed-by:
Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by:
Neil Armstrong <neil.armstrong@linaro.org> Reviewed-by:
-
Robert Marko authored
Convert the DT binding for GPIO WDT to JSON schema. Cc: luka.perkov@sartura.hr Signed-off-by:
Robert Marko <robert.marko@sartura.hr> Reviewed-by:
-
Cosmin Tanislav authored
HW running watchdogs are just watchdogs that are enabled before the Linux driver is probed, usually by the bootloader (eg. U-Boot). When the system is shutting down, the mechanism for keeping a HW running watchdog pinged is also stopped, but the watchdog itself is not stopped, causing a reset, and preventing the system from being shut down. Opt into stopping watchdogs on reboot. Signed-off-by:
Cosmin Tanislav <cosmin.tanislav@analog.com> Reviewed-by:
-
Uwe Kleine-König authored
The probe function doesn't make use of the i2c_device_id * parameter so it can be trivially converted. Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by:
-
Thomas Weißschuh authored
Synchronize the reported information in dmesg and the watchdog APIs. Signed-off-by:
-
Krzysztof Kozlowski authored
On some SoCs the watchdog device is actually mixed with timer, e.g. the qcom,msm-timer on older Qualcomm SoCs where this is actually one hardware block responsible for both system timer and watchdog. Allow calling such device nodes as "timer". Signed-off-by:
-
Primoz Fiser authored
Machine resets via da9062/da9063 PMICs are challenging since one needs to use special i2c atomic transfers due to the fact interrupts are disabled in such late system stages. This is the reason both PMICs don't use regmap and have instead opted for i2c_smbus_write_byte_data() in restart handlers. However extensive testing revealed that even using atomic safe function is not enough and occasional resets fail with error message "Failed to shutdown (err = -11)". This is due to the fact that function i2c_smbus_write_byte_data() in turn calls __i2c_lock_bus_helper() which might fail with -EAGAIN when bus lock is already taken and cannot be released anymore. Thus replace i2c_smbus_write_byte_data() with unlocked flavor of i2c_smbus_xfer() function to avoid above dead-lock scenario. At this system stage we don't care about proper locking anymore and only want proper machine reset to be carried out. Signed-off-by:
Primoz Fiser <primoz.fiser@norik.com> Reviewed-by:
-
- 12 Feb, 2023 12 commits
-
-
Thomas Weißschuh authored
As per the specification the action QUERY_COUNTDOWN_PERIOD is optional. If the action is not implemented by the physical device the driver would always report "0" from get_timeleft(). Avoid confusing userspace by only providing get_timeleft() when implemented by the hardware. Signed-off-by:
-
Christophe JAILLET authored
The devm_clk_get_enabled() helper: - calls devm_clk_get() - calls clk_prepare_enable() and registers what is needed in order to call clk_disable_unprepare() when needed, as a managed resource. This simplifies the code and avoids the need of a dedicated function used with devm_add_action_or_reset(). Signed-off-by:Sven Peter <sven@svenpeter.dev> Link: https://lore.kernel.org/r/6f312af6160d1e10b616c9adbd1fd8f822db964d.1672473415.git.christophe.jaillet@wanadoo.frSigned-off-by:
-
Christophe JAILLET authored
The devm_clk_get_enabled() helper: - calls devm_clk_get() - calls clk_prepare_enable() and registers what is needed in order to call clk_disable_unprepare() when needed, as a managed resource. This simplifies the code and avoids the need of a dedicated function used with devm_add_action_or_reset(). Signed-off-by: -
Christophe JAILLET authored
The devm_clk_get_enabled() helper: - calls devm_clk_get() - calls clk_prepare_enable() and registers what is needed in order to call clk_disable_unprepare() when needed, as a managed resource. This simplifies the code and avoids the need of a dedicated function used with devm_add_action_or_reset(). Signed-off-by: -
Christophe JAILLET authored
The devm_clk_get_enabled() helper: - calls devm_clk_get() - calls clk_prepare_enable() and registers what is needed in order to call clk_disable_unprepare() when needed, as a managed resource. This simplifies the code and avoids the need of a dedicated function used with devm_add_action_or_reset(). Signed-off-by: -
Christophe JAILLET authored
The devm_clk_get_enabled() helper: - calls devm_clk_get() - calls clk_prepare_enable() and registers what is needed in order to call clk_disable_unprepare() when needed, as a managed resource. This simplifies the code and avoids the need of a dedicated function used with devm_add_action_or_reset(). Signed-off-by: -
Christophe JAILLET authored
The devm_clk_get_enabled() helper: - calls devm_clk_get() - calls clk_prepare_enable() and registers what is needed in order to call clk_disable_unprepare() when needed, as a managed resource. This simplifies the code and avoids the need of a dedicated function used with devm_add_action_or_reset(). Signed-off-by:Florian Fainelli <f.fainelli@gmail.com> Reviewed-by:
-
Christophe JAILLET authored
The devm_clk_get_enabled() helper: - calls devm_clk_get() - calls clk_prepare_enable() and registers what is needed in order to call clk_disable_unprepare() when needed, as a managed resource. This simplifies the code and avoids the need of a dedicated function used with devm_add_action_or_reset(). Signed-off-by: -
Christophe JAILLET authored
The devm_clk_get_enabled() helper: - calls devm_clk_get() - calls clk_prepare_enable() and registers what is needed in order to call clk_disable_unprepare() when needed, as a managed resource. This simplifies the code and avoids the need of a dedicated function used with devm_add_action_or_reset(). Signed-off-by: -
Christophe JAILLET authored
The devm_clk_get_enabled() helper: - calls devm_clk_get() - calls clk_prepare_enable() and registers what is needed in order to call clk_disable_unprepare() when needed, as a managed resource. This simplifies the code and avoids the need of a dedicated function used with devm_add_action_or_reset(). Signed-off-by: -
Christophe JAILLET authored
The devm_clk_get_enabled() helper: - calls devm_clk_get() - calls clk_prepare_enable() and registers what is needed in order to call clk_disable_unprepare() when needed, as a managed resource. This simplifies the code and avoids the need of a dedicated function used with devm_add_action_or_reset(). Signed-off-by: -
Christophe JAILLET authored
The devm_clk_get_enabled() helper: - calls devm_clk_get() - calls clk_prepare_enable() and registers what is needed in order to call clk_disable_unprepare() when needed, as a managed resource. This simplifies the code and avoids the need of a dedicated function used with devm_add_action_or_reset(). Signed-off-by:
-
