Whenever the interface is brought up/down then set_rx_mode
function is called by the stack which enables promisc/allmulti
MCAM entries. But there are cases when driver brings
interface down and then up such as while changing number
of channels. In these cases promisc/allmulti MCAM entries
are left disabled as set_rx_mode callback is not called.
This patch enables these MCAM entries in all such cases.
Signed-off-by: Rakesh Babu <rsaladi2@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously with CONFIG_QRTR=m a separate ns.ko would be built which
wasn't done on purpose and should be included in qrtr.ko.

Rename qrtr.c to af_qrtr.c so we can build a qrtr.ko with both af_qrtr.c
and ns.c.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-By: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://lore.kernel.org/r/20210928171156.6353-1-luca@z3ntu.xyzSigned-off-by: Jakub Kicinski <kuba@kernel.org>

fib_notifier.c hasn't use any macro or function declared
in net/netns/ipv4.h.

Thus, these files can be removed from fib_notifier.c safely
without affecting the compilation of the net/ipv4 module.
Signed-off-by: Mianhan Liu <liumh1@shanghaitech.edu.cn>
Link: https://lore.kernel.org/r/20210928164011.1454-1-liumh1@shanghaitech.edu.cnSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The use of dma_unmap_addr()/dma_unmap_len() in the driver causes
multiple warnings when these macros are defined as empty, e.g.
in an ARCH=i386 allmodconfig build:

drivers/net/ethernet/google/gve/gve_tx_dqo.c: In function 'gve_tx_add_skb_no_copy_dqo':
drivers/net/ethernet/google/gve/gve_tx_dqo.c:494:40: error: unused variable 'buf' [-Werror=unused-variable]
  494 |                 struct gve_tx_dma_buf *buf =

This is not how the NEED_DMA_MAP_STATE macros are meant to work,
as they rely on never using local variables or a temporary structure
like gve_tx_dma_buf.

Remote the gve_tx_dma_buf definition and open-code the contents
in all places to avoid the warning. This causes some rather long
lines but otherwise ends up making the driver slightly smaller.

Fixes: a57e5de4 ("gve: DQO: Add TX path")
Link: https://lore.kernel.org/netdev/20210723231957.1113800-1-bcf@google.com/
Link: https://lore.kernel.org/netdev/20210721151100.2042139-1-arnd@kernel.org/Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current driver uses software CQ head pointer to poll on CQE
header in memory to determine if CQE is valid. Software needs
to make sure, that the reads of the CQE do not get re-ordered
so much that it ends up with an inconsistent view of the CQE.
To ensure that DMB barrier after read to first CQE cacheline
and before reading of the rest of the CQE is needed.
But having barrier for every CQE read will impact the performance,
instead use hardware CQ head and tail pointers to find the
valid number of CQEs.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hariprasad Kelam says:

====================
Externel ptp clock support

Externel ptp support is required in a scenario like connecting
a external timing device to the chip for time synchronization.
This series of patches adds support to ptp driver to use external
clock and enables PTP config in CN10K MAC block (RPM). Currently
PTP configuration is left unchanged in FLR handler these patches
addresses the same.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
,

PTP hardware block can be configured to utilize
the external clock. Also the current ptp timestamp
can be captured when external trigger is applied on
a gpio pin. These features are required in scenarios
like connecting a external timing device to the chip
for time synchronization. The timing device provides
the clock and trigger(PPS signal) to the PTP block.
This patch does the following:
1. configures PTP block to use external clock
frequency and timestamp capture on external event.
2. sends PTP_REQ_EXTTS events to kernel ptp phc susbsytem
with captured timestamps
3. aligns PPS edge to adjusted ptp clock in the ptp device
by setting the PPS_THRESH to the reminder of the last
timestamp value captured by external PPS
Signed-off-by: Yi Guo <yig@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The input clock frequency of PTP block is figured
out from hardware reset block currently. The firmware
data already has this info in sclk. Hence simplify
ptp driver to use sclk from firmware data.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MAC on CN10K support hardware timestamping such that 8 bytes addition
header is prepended to incoming packets. This patch does necessary
configuration to enable Hardware time stamping upon receiving request
from PF netdev interfaces.

Timestamp configuration is different on MAC (CGX) Octeontx2 silicon
and MAC (RPM) OcteonTX3 CN10k. Based on silicon variant appropriate
fn() pointer is called. Refactor MAC specific mbox messages to remove
unnecessary gaps in mboxids.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Upon receiving ptp config request from netdev interface , Octeontx2 MAC
block CGX is configured to append timestamp to every incoming packet
and NPC config is updated with DMAC offset change.

Currently this configuration is not reset in FLR handler. This patch
resets the same.
Signed-off-by: Harman Kalra <hkalra@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The IV of CCM mode has special requirements, this patch supports CCM
mode of SM4 algorithm.
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kbuild supports <modname>-y as well as <modname>-objs.
This simplifies the Makefile.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Assign the objects directly to obj-$(CONFIG_INET).
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

My previous patch had an off-by-one error in the added sanity
check, the arrays are MTL_MAX_{RX,TX}_QUEUES long, so if that
index is that number, it has overflown.

The patch silenced the warning anyway because the strings could
no longer overlap with the input, but they could still overlap
with other fields.

Fixes: 3e0d5699 ("net: stmmac: fix gcc-10 -Wrestrict warning")
Reported-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

clang warns about arithmetic on NULL pointers:

drivers/net/ethernet/ti/am65-cpsw-ethtool.c:71:2: error: performing pointer subtraction with a null pointer has undefined behavior [-Werror,-Wnull-pointer-subtraction]
        AM65_CPSW_REGDUMP_REC(AM65_CPSW_REGDUMP_MOD_NUSS, 0x0, 0x1c),
        ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/ti/am65-cpsw-ethtool.c:64:29: note: expanded from macro 'AM65_CPSW_REGDUMP_REC'
        .hdr.len = (((u32 *)(end)) - ((u32 *)(start)) + 1) * sizeof(u32) * 2 + \
                                   ^ ~~~~~~~~~~~~~~~~

The expression here is easily changed to a calculation based on integers
that is no less readable.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

When rhashtable_init() fails, it returns -EINVAL.
However, since error return value of rhashtable_init is not checked,
it can cause use of uninitialized pointers.
So, fix unhandled errors of rhashtable_init.
Signed-off-by: MichelleJin <shjy180909@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When rhashtable_init() fails, it returns -EINVAL.
However, since error return value of rhashtable_init is not checked,
it can cause use of uninitialized pointers.
So, fix unhandled errors of rhashtable_init.
Signed-off-by: MichelleJin <shjy180909@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When rhashtable_init() fails, it returns -EINVAL.
However, since error return value of rhashtable_init is not checked,
it can cause use of uninitialized pointers.
So, fix unhandled errors of rhashtable_init.
Signed-off-by: MichelleJin <shjy180909@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: bcmgenet: support for flow control

This patch series adds support for flow control to the GENET driver, the
first 2 patches remove superfluous code, the 3rd one does re-organize
code a little bit and the 4th one ads the support for flow control
proper.
====================

This commit extends the supported ethtool operations to allow MAC
level flow control to be configured for the bcmgenet driver.

The ethtool utility can be used to change the configuration of
auto-negotiated symmetric and asymmetric modes as well as manually
configuring support for RX and TX Pause frames individually.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit separates out the MAC configuration that occurs on a
PHY state change into a function named bcmgenet_mac_config().

This allows the function to be called directly elsewhere.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PHY state machine has been fixed to only call the adjust_link
callback when the link state has changed. Therefore the old link
state variables are no longer needed to detect a change in link
state.

This commit effectively reverts
commit 5ad6e6c5 ("net: bcmgenet: improve bcmgenet_mii_setup()")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bcmgenet_mii_setup() function is registered as the adjust_link
callback from the phylib for the GENET driver.

The phylib always sets the netif_carrier according to phydev->link
prior to invoking the adjust_link callback, so there is no need to
repeat that in the link down case within the network driver.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Linus Walleij says:

====================
RTL8366(RB) cleanups part 1

This is a first set of patches making the RTL8366RB work out of
the box with a default OpenWrt userspace.

We achieve bridge port isolation with the first patch, and the
next 5 patches removes the very weird VLAN set-up with one
VLAN with PVID per port that has been in this driver in all
vendor trees and in OpenWrt for years.

The switch is now managed the way a modern bridge/DSA switch
shall be managed.

After these patches are merged, I will send the next set which
adds new features, some which have circulated before.

ChangeLog v4->v5:
- Drop the patch disabling 4K VLAN.
- Drop the patch forcing VLAN0 untagged.
- Fix a semantic bug in the filer enablement code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We don't need a message for every VLAN association, dbg
is fine. The message about adding the DSA or CPU
port to a VLAN is directly misleading, this is perfectly
fine.

Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We were checking that the MC (member config) was != 0
for some reason, all we need to check is that the config
has no ports, i.e. no members. Then it can be recycled.
This must be some misunderstanding.

Fixes: 4ddcaf1e ("net: dsa: rtl8366: Properly clear member config")
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The max VLAN number with non-4K VLAN activated is 15, and the
range is 0..15. Not 16.

The impact should be low since we by default have 4K VLAN and
thus have 4095 VLANs to play with in this switch. There will
not be a problem unless the code is rewritten to only use
16 VLANs.

Fixes: d8652956 ("net: dsa: realtek-smi: Add Realtek SMI driver")
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While we were defining one VLAN per port for isolating the ports
the port_vlan_filtering() callback was implemented to enable a
VLAN on the port + 1. This function makes no sense, not only is
it incomplete as it only enables the VLAN, it doesn't do what
the callback is supposed to do, which is to selectively enable
and disable filtering on a certain port.

Implement the correct callback: we have two registers dealing
with filtering on the RTL9366RB, so we implement an ASIC-specific
callback and implement filering using the register bit that makes
the switch drop frames if the port is not in the VLAN member set.

The DSA documentation Documentation/networking/switchdev.rst states:

  When the bridge has VLAN filtering enabled and a PVID is not
  configured on the ingress port, untagged and 802.1p tagged
  packets must be dropped. When the bridge has VLAN filtering
  enabled and a PVID exists on the ingress port, untagged and
  priority-tagged packets must be accepted and forwarded according
  to the bridge's port membership of the PVID VLAN. When the
  bridge has VLAN filtering disabled, the presence/lack of a
  PVID should not influence the packet forwarding decision.

To comply with this, we add two arrays of bool in the RTL8366RB
state that keeps track of if filtering and PVID is enabled or
not for each port. We then add code such that whenever filtering
or PVID changes, we update the filter according to the
specification.

Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: Alvin Šipraga <alsi@bang-olufsen.dk>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This hacky default VLAN setup was done in order to direct
packets to the right ports and provide port isolation, both
which we now support properly using custom tags and proper
bridge port isolation.

We can drop the custom VLAN code and leave all VLAN handling
alone, as users expect things to be. We can also drop
ds->configure_vlan_while_not_filtering = false; and let
the core deal with any VLANs it wants.

Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use port isolation registers to configure bridge offloading.

Tested on the D-Link DIR-685, switching between ports and
sniffing ports to make sure no packets leak.

Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Leon Romanovsky says:

====================
Move devlink_register to be last devlink command

This is second version of patch series
https://lore.kernel.org/netdev/cover.1628599239.git.leonro@nvidia.com/

The main change is addition of delayed notification logic that will
allowed us to delete devlink_params_publish API (future series will
remove it completely) and conversion of all drivers to have devlink_register
being last commend.

The series itself is pretty straightforward, except liquidio driver
which performs initializations in various workqueues without proper
locks. That driver doesn't hole device_lock and it is clearly broken
for any parallel driver core flows (modprobe + devlink + PCI reset will
100% crash it).

In order to annotate devlink_register() will lockdep of holding
device_lock, I added workaround in this driver.

Thanks

----------------------
From previous cover letter:
Hi Dave and Jakub,

This series prepares code to remove devlink_reload_enable/_disable API
and in order to do, we move all devlink_register() calls to be right
before devlink_reload_enable().

The best place for such a call should be right before exiting from
the probe().

This is done because devlink_register() opens devlink netlink to the
users and gives them a venue to issue commands before initialization
is finished.

1. Some drivers were aware of such "functionality" and tried to protect
themselves with extra locks, state machines and devlink_reload_enable().
Let's assume that it worked for them, but I'm personally skeptical about
it.

2. Some drivers copied that pattern, but without locks and state
machines. That protected them from reload flows, but not from any _set_
routines.

3. And all other drivers simply didn't understand the implications of early
devlink_register() and can be seen as "broken".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This change prevents from users to access device before devlink
is fully configured.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change prevents from users to access device before devlink is
fully configured.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change prevents from users to access device before devlink is
fully configured.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change prevents from users to access device before devlink is
fully configured. Indirectly this change fixes the commit mentioned
below where devlink_unregister() was prematurely removed.

Fixes: db4278c5 ("devlink: Make devlink_register to be void")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change prevents from users to access device before devlink is
fully configured.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change prevents from users to access device before devlink is
fully configured.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change prevents from users to access device before devlink is
fully configured.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change prevents from users to access device before devlink is
fully configured.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Open user space access to the devlink after driver is probed.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>