- ors: establish backward compatibility proxy to software-ors.cfg
- generic: correct pucch_dedicated setup for CA
- generic: Move user-authorized-key back to be eNB property instead of RU property
- generic: Adjust cell schemas for root_sequence_index - it is a bit different in between LTE and NE
- generic: Restore CPRI delay defaults for Lopcomm and Sunwave
- generic: Fix address of GTP-on-loopback
- misc...

* master:
  software/end-to-end-testing: add test_ors.py
  software/end-to-end-testing: add test_lopcomm.py
  component/python3: version up python3.11.8
  stack/slapos: version up pyparsing (3.1.1 on py3, 2.4.7 on py2)
  stack/slapos: version up defusedxml 0.7.1
  component/pygolang: remove some duplicate versions
  *: normalize versions of pexpect
  stack/slapos: move httplib2 version pin in slapos.cfg and update to 0.22.0
  component/ZODB: update ZODB5 5.8.1
  software/gitlab: run git-backup test during software step
  software/gitlab: version up gilab-ce
  software/gitlab: remove outdated comment

Original SR had defaults as

mme.gtp: 127.0.1.100
enb.gtp: 127.0.1.1

With this both can listen at the same port and talk to each other.

But if we set gtp addr to be the same for mme and enb, then enb listen
will fail as the listening address is already taken by mme.

Fix it with restoring explicit enb gtp loopback default.

rx_delay is meaningful to have as the default, as that is RU-model
specific and goes as T2a+T3a-Toffset.

tx_delay is less meaningful to have as the default: it is T12 + T2a,
where T2a is RU-model specific and T12 depends on the length of the
fiber link. But I keep the previous default because it might be handy to
have something as the default.

Also restore previous values for sunwave n_antenna_* as it was there in
old ors-amarisoft SR.

The code already behaved in the "updated" way with

    slaplte.jinja2:{%-     do cell.setdefault('root_sequence_index', 1 + 203*(cell.cell_type == 'lte') + n)  %}

See merge request nexedi/slapos!1531

See merge request nexedi/slapos!1529

These are already defined in stack/slapos.cfg

jupyter-py2 used an old version not py3 compatible
pygolang/test used the same version as in stack/slapos.cfg

* master:
  software/ors-amarisoft: enb.jinja2.cfg: Increase SNR in handover code
  software/ors-amarisoft: enb.jinja2.cfg: Factor handover code into one place
  software/ors-amarisoft: slapos-render-config: Test handover
  software/ors-amarisoft: enb.jinja2.cfg: Unify logging
  software/ors-amarisoft: test: Preprocess enb.cfg & co on YAML loading
  software/ors-amarisoft: test: Avoid YAMLLoadWarning warning
  software/ors-amarisoft: test: Factor loading YAML config into dedicated function
  software/ors-amarisoft: Merge instance-gnb.jinja2.cfg into instance-enb.jinja2.cfg
  software/ors-amarisoft: Start to introduce ORS mode
  software/ors-amarisoft: Rename ors-id -> comp-id
  software/ors-amarisoft: enb.jinja2.cfg: Tune PUCCH 1 and PUCCH 3 for CA
  stack/erp5: version up erp5diff 0.8.1.9

Don't repeat slapparameter_dict['ncell_list'][k] - we can introduce a name for
current neighbour cell, and use that name in the loop. And align entries to
that they read more clearly.

No non-whitespace changes in rendered enb.cfg and gnb.cfg .

/cc @jhuge, @lu.xu, @tomo, @xavier_thompson, @Daetalus
/proposed-for-review-on nexedi/slapos!1526
/reviewed-by TrustMe

We currently have LTE-specific handover configuration in under cell_list and
NR-specific handover configuration in under nr_cell_list. Those configuration
are different.

However in upcoming MultiRU we will need to handle LTE->NR handover, NR->LTE
handover, and also Intra-ENB handover in addition to Inter-ENB handover we
currently do.

-> Move handover code into common function as a preparatory step for that.

In the future the handover code for LTE and NR cells will be the same, so it
makes sense to move that code to common place to avoid duplication.

For rendered enb.cfg this unification introduces only space and trivial
changes as shown in the appendix.

/cc @jhuge, @lu.xu, @tomo, @xavier_thompson, @Daetalus
/proposed-for-review-on nexedi/slapos!1528
/reviewed-by TrustMe

Appendix. Diff for rendered enb.cfg and gnb.cfg before and after this patch

```
$ git diff -w --no-index config/{old,out}
```

```diff
diff --git a/config/old/enb.cfg b/config/out/enb.cfg
index 43301ee13..9dcca16c7 100644
--- a/config/old/enb.cfg
+++ b/config/out/enb.cfg
@@ -45,16 +45,18 @@
       root_sequence_index: 204,
       dl_earfcn: 36100,
       inactivity_timer: 10000,
+
       // Handover
       ncell_list: [
         // Inter-ENB HO
         {
+          rat: "eutra",
           n_id_cell: 35,
           dl_earfcn: 700,
           cell_id: 0x12345,
           tac: 123,
-        }],
-
+        },
+      ],

       // Carrier Aggregation
       scell_list: [
diff --git a/config/old/gnb.cfg b/config/out/gnb.cfg
index 2127a2f6b..23b07d6e1 100644
--- a/config/old/gnb.cfg
+++ b/config/out/gnb.cfg
@@ -57,6 +57,7 @@
     ssb_pos_bitmap: "10000000",

     inactivity_timer: 10000,
+
       // Handover
       ncell_list: [
         // Inter-ENB HO
@@ -74,8 +75,8 @@
           ssb_period: 20,
           ssb_offset: 0,
           ssb_duration: 1,
-      }],
-
+        },
+      ],

     // tune NR parameters for the cell
     manual_ref_signal_power: true,
```

Useful to have while doing handover-related changes.

/cc @jhuge, @lu.xu, @tomo, @xavier_thompson, @Daetalus
/proposed-for-review-on nexedi/slapos!1528
/reviewed-by TrustMe

Appendix. Diff for rendered enb.cfg and gnb.cfg before and after this patch

```
$ git diff --no-index config/{old,out}
```

```diff
diff --git a/config/old/enb.cfg b/config/out/enb.cfg
index 1843e0f24..43301ee13 100644
--- a/config/old/enb.cfg
+++ b/config/out/enb.cfg
@@ -45,6 +45,16 @@
       root_sequence_index: 204,
       dl_earfcn: 36100,
       inactivity_timer: 10000,
+      // Handover
+      ncell_list: [
+        // Inter-ENB HO
+        {
+          n_id_cell: 35,
+          dl_earfcn: 700,
+          cell_id: 0x12345,
+          tac: 123,
+        }],
+

       // Carrier Aggregation
       scell_list: [
diff --git a/config/old/gnb.cfg b/config/out/gnb.cfg
index d76b45d3c..2127a2f6b 100644
--- a/config/old/gnb.cfg
+++ b/config/out/gnb.cfg
@@ -57,6 +57,25 @@
     ssb_pos_bitmap: "10000000",

     inactivity_timer: 10000,
+    // Handover
+    ncell_list: [
+      // Inter-ENB HO
+      {
+        rat: "nr",
+        dl_nr_arfcn: 520000,
+        ssb_nr_arfcn: ,
+        ul_nr_arfcn: 520000,
+        n_id_cell: 75,
+        gnb_id_bits: 22,
+        nr_cell_id: 0x77712,
+        tac: 321,
+        band: 38,
+        ssb_subcarrier_spacing: 30,
+        ssb_period: 20,
+        ssb_offset: 0,
+        ssb_duration: 1,
+      }],
+
```