autogenerated headers for rev...

autogenerated headers for rev https://github.com/mavlink/mavlink/tree/010dbcebcc216be9ab04da9f1102d7a2da826e8e

ASLUAV/ASLUAV.h

@@ -142,7 +142,7 @@ typedef enum MAV_CMD
    MAV_CMD_DO_JUMP_TAG=601, /* Jump to the matching tag in the mission list. Repeat this action for the specified number of times. A mission should contain a single matching tag for each jump. If this is not the case then a jump to a missing tag should complete the mission, and a jump where there are multiple matching tags should always select the one with the lowest mission sequence number. |Target tag to jump to.| Repeat count.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_PARAM_TRANSACTION=900, /* Request to start or end a parameter transaction. Multiple kinds of transport layers can be used to exchange parameters in the transaction (param, param_ext and mavftp). The command response can either be a success/failure or an in progress in case the receiving side takes some time to apply the parameters. |Action to be performed (start, commit, cancel, etc.)| Possible transport layers to set and get parameters via mavlink during a parameter transaction.| Identifier for a specific transaction.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_DO_GIMBAL_MANAGER_TILTPAN=1000, /* High level setpoint to be sent to a gimbal manager to set a gimbal attitude. It is possible to set combinations of the values below. E.g. an angle as well as a desired angular rate can be used to get to this angle at a certain angular rate, or an angular rate only will result in continuous turning. NaN is to be used to signal unset. Note: a gimbal is never to react to this command but only the gimbal manager. |Tilt/pitch rate (positive to tilt up).| Pan/yaw rate (positive to pan to the right).| Tilt/pitch angle (positive to tilt up, relative to vehicle for PAN mode, relative to world horizon for HOLD mode).| Pan/yaw angle (positive to pan to the right, relative to vehicle for PAN mode, absolute to North for HOLD mode).| Gimbal manager flags to use.| Reserved (default:0)| Component ID of gimbal device to address (or 1-6 for non-MAVLink gimbal), 0 for all gimbal device components. (Send command multiple times for more than one but not all gimbals.)|  */
-   MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1), otherwise set to 0. Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted.| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)|  */
    MAV_CMD_IMAGE_STOP_CAPTURE=2001, /* Stop image capture sequence Use NaN for reserved values. |Reserved (Set to 0)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)|  */
    MAV_CMD_REQUEST_CAMERA_IMAGE_CAPTURE=2002, /* Re-request a CAMERA_IMAGE_CAPTURED message. |Sequence number for missing CAMERA_IMAGE_CAPTURED message| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)|  */
    MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| 1 to pause triggering, but without switching the camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */

ASLUAV/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Wed Sep 16 2020"
+#define MAVLINK_BUILD_DATE "Thu Sep 17 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

ardupilotmega/ardupilotmega.h

@@ -162,7 +162,7 @@ typedef enum MAV_CMD
    MAV_CMD_DO_JUMP_TAG=601, /* Jump to the matching tag in the mission list. Repeat this action for the specified number of times. A mission should contain a single matching tag for each jump. If this is not the case then a jump to a missing tag should complete the mission, and a jump where there are multiple matching tags should always select the one with the lowest mission sequence number. |Target tag to jump to.| Repeat count.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_PARAM_TRANSACTION=900, /* Request to start or end a parameter transaction. Multiple kinds of transport layers can be used to exchange parameters in the transaction (param, param_ext and mavftp). The command response can either be a success/failure or an in progress in case the receiving side takes some time to apply the parameters. |Action to be performed (start, commit, cancel, etc.)| Possible transport layers to set and get parameters via mavlink during a parameter transaction.| Identifier for a specific transaction.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_DO_GIMBAL_MANAGER_TILTPAN=1000, /* High level setpoint to be sent to a gimbal manager to set a gimbal attitude. It is possible to set combinations of the values below. E.g. an angle as well as a desired angular rate can be used to get to this angle at a certain angular rate, or an angular rate only will result in continuous turning. NaN is to be used to signal unset. Note: a gimbal is never to react to this command but only the gimbal manager. |Tilt/pitch rate (positive to tilt up).| Pan/yaw rate (positive to pan to the right).| Tilt/pitch angle (positive to tilt up, relative to vehicle for PAN mode, relative to world horizon for HOLD mode).| Pan/yaw angle (positive to pan to the right, relative to vehicle for PAN mode, absolute to North for HOLD mode).| Gimbal manager flags to use.| Reserved (default:0)| Component ID of gimbal device to address (or 1-6 for non-MAVLink gimbal), 0 for all gimbal device components. (Send command multiple times for more than one but not all gimbals.)|  */
-   MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1), otherwise set to 0. Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted.| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)|  */
    MAV_CMD_IMAGE_STOP_CAPTURE=2001, /* Stop image capture sequence Use NaN for reserved values. |Reserved (Set to 0)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)|  */
    MAV_CMD_REQUEST_CAMERA_IMAGE_CAPTURE=2002, /* Re-request a CAMERA_IMAGE_CAPTURED message. |Sequence number for missing CAMERA_IMAGE_CAPTURED message| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)|  */
    MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| 1 to pause triggering, but without switching the camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */

ardupilotmega/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Wed Sep 16 2020"
+#define MAVLINK_BUILD_DATE "Thu Sep 17 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

autoquad/autoquad.h

@@ -186,7 +186,7 @@ typedef enum MAV_CMD
    MAV_CMD_DO_JUMP_TAG=601, /* Jump to the matching tag in the mission list. Repeat this action for the specified number of times. A mission should contain a single matching tag for each jump. If this is not the case then a jump to a missing tag should complete the mission, and a jump where there are multiple matching tags should always select the one with the lowest mission sequence number. |Target tag to jump to.| Repeat count.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_PARAM_TRANSACTION=900, /* Request to start or end a parameter transaction. Multiple kinds of transport layers can be used to exchange parameters in the transaction (param, param_ext and mavftp). The command response can either be a success/failure or an in progress in case the receiving side takes some time to apply the parameters. |Action to be performed (start, commit, cancel, etc.)| Possible transport layers to set and get parameters via mavlink during a parameter transaction.| Identifier for a specific transaction.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_DO_GIMBAL_MANAGER_TILTPAN=1000, /* High level setpoint to be sent to a gimbal manager to set a gimbal attitude. It is possible to set combinations of the values below. E.g. an angle as well as a desired angular rate can be used to get to this angle at a certain angular rate, or an angular rate only will result in continuous turning. NaN is to be used to signal unset. Note: a gimbal is never to react to this command but only the gimbal manager. |Tilt/pitch rate (positive to tilt up).| Pan/yaw rate (positive to pan to the right).| Tilt/pitch angle (positive to tilt up, relative to vehicle for PAN mode, relative to world horizon for HOLD mode).| Pan/yaw angle (positive to pan to the right, relative to vehicle for PAN mode, absolute to North for HOLD mode).| Gimbal manager flags to use.| Reserved (default:0)| Component ID of gimbal device to address (or 1-6 for non-MAVLink gimbal), 0 for all gimbal device components. (Send command multiple times for more than one but not all gimbals.)|  */
-   MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1), otherwise set to 0. Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted.| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)|  */
    MAV_CMD_IMAGE_STOP_CAPTURE=2001, /* Stop image capture sequence Use NaN for reserved values. |Reserved (Set to 0)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)|  */
    MAV_CMD_REQUEST_CAMERA_IMAGE_CAPTURE=2002, /* Re-request a CAMERA_IMAGE_CAPTURED message. |Sequence number for missing CAMERA_IMAGE_CAPTURED message| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)|  */
    MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| 1 to pause triggering, but without switching the camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */

autoquad/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Wed Sep 16 2020"
+#define MAVLINK_BUILD_DATE "Thu Sep 17 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

common/common.h

@@ -635,7 +635,7 @@ typedef enum MAV_CMD
    MAV_CMD_DO_JUMP_TAG=601, /* Jump to the matching tag in the mission list. Repeat this action for the specified number of times. A mission should contain a single matching tag for each jump. If this is not the case then a jump to a missing tag should complete the mission, and a jump where there are multiple matching tags should always select the one with the lowest mission sequence number. |Target tag to jump to.| Repeat count.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_PARAM_TRANSACTION=900, /* Request to start or end a parameter transaction. Multiple kinds of transport layers can be used to exchange parameters in the transaction (param, param_ext and mavftp). The command response can either be a success/failure or an in progress in case the receiving side takes some time to apply the parameters. |Action to be performed (start, commit, cancel, etc.)| Possible transport layers to set and get parameters via mavlink during a parameter transaction.| Identifier for a specific transaction.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_DO_GIMBAL_MANAGER_TILTPAN=1000, /* High level setpoint to be sent to a gimbal manager to set a gimbal attitude. It is possible to set combinations of the values below. E.g. an angle as well as a desired angular rate can be used to get to this angle at a certain angular rate, or an angular rate only will result in continuous turning. NaN is to be used to signal unset. Note: a gimbal is never to react to this command but only the gimbal manager. |Tilt/pitch rate (positive to tilt up).| Pan/yaw rate (positive to pan to the right).| Tilt/pitch angle (positive to tilt up, relative to vehicle for PAN mode, relative to world horizon for HOLD mode).| Pan/yaw angle (positive to pan to the right, relative to vehicle for PAN mode, absolute to North for HOLD mode).| Gimbal manager flags to use.| Reserved (default:0)| Component ID of gimbal device to address (or 1-6 for non-MAVLink gimbal), 0 for all gimbal device components. (Send command multiple times for more than one but not all gimbals.)|  */
-   MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1), otherwise set to 0. Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted.| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)|  */
    MAV_CMD_IMAGE_STOP_CAPTURE=2001, /* Stop image capture sequence Use NaN for reserved values. |Reserved (Set to 0)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)|  */
    MAV_CMD_REQUEST_CAMERA_IMAGE_CAPTURE=2002, /* Re-request a CAMERA_IMAGE_CAPTURED message. |Sequence number for missing CAMERA_IMAGE_CAPTURED message| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)|  */
    MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| 1 to pause triggering, but without switching the camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */

common/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Wed Sep 16 2020"
+#define MAVLINK_BUILD_DATE "Thu Sep 17 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

icarous/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Wed Sep 16 2020"
+#define MAVLINK_BUILD_DATE "Thu Sep 17 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 46
  

matrixpilot/matrixpilot.h

@@ -159,7 +159,7 @@ typedef enum MAV_CMD
    MAV_CMD_DO_JUMP_TAG=601, /* Jump to the matching tag in the mission list. Repeat this action for the specified number of times. A mission should contain a single matching tag for each jump. If this is not the case then a jump to a missing tag should complete the mission, and a jump where there are multiple matching tags should always select the one with the lowest mission sequence number. |Target tag to jump to.| Repeat count.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_PARAM_TRANSACTION=900, /* Request to start or end a parameter transaction. Multiple kinds of transport layers can be used to exchange parameters in the transaction (param, param_ext and mavftp). The command response can either be a success/failure or an in progress in case the receiving side takes some time to apply the parameters. |Action to be performed (start, commit, cancel, etc.)| Possible transport layers to set and get parameters via mavlink during a parameter transaction.| Identifier for a specific transaction.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_DO_GIMBAL_MANAGER_TILTPAN=1000, /* High level setpoint to be sent to a gimbal manager to set a gimbal attitude. It is possible to set combinations of the values below. E.g. an angle as well as a desired angular rate can be used to get to this angle at a certain angular rate, or an angular rate only will result in continuous turning. NaN is to be used to signal unset. Note: a gimbal is never to react to this command but only the gimbal manager. |Tilt/pitch rate (positive to tilt up).| Pan/yaw rate (positive to pan to the right).| Tilt/pitch angle (positive to tilt up, relative to vehicle for PAN mode, relative to world horizon for HOLD mode).| Pan/yaw angle (positive to pan to the right, relative to vehicle for PAN mode, absolute to North for HOLD mode).| Gimbal manager flags to use.| Reserved (default:0)| Component ID of gimbal device to address (or 1-6 for non-MAVLink gimbal), 0 for all gimbal device components. (Send command multiple times for more than one but not all gimbals.)|  */
-   MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1), otherwise set to 0. Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted.| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)|  */
    MAV_CMD_IMAGE_STOP_CAPTURE=2001, /* Stop image capture sequence Use NaN for reserved values. |Reserved (Set to 0)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)|  */
    MAV_CMD_REQUEST_CAMERA_IMAGE_CAPTURE=2002, /* Re-request a CAMERA_IMAGE_CAPTURED message. |Sequence number for missing CAMERA_IMAGE_CAPTURED message| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)|  */
    MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| 1 to pause triggering, but without switching the camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */

matrixpilot/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Wed Sep 16 2020"
+#define MAVLINK_BUILD_DATE "Thu Sep 17 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

message_definitions/common.xml

@@ -1736,9 +1736,11 @@
         <description>Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values.</description>
         <param index="1">Reserved (Set to 0)</param>
         <param index="2" label="Interval" units="s" minValue="0">Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).</param>
-        <param index="3" label="Capture Count" minValue="0" increment="1">Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.</param>
-        <param index="4" label="Sequence Number" minValue="1" increment="1">Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.</param>
-        <param index="5">Reserved (all remaining params)</param>
+        <param index="3" label="Total Images" minValue="0" increment="1">Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.</param>
+        <param index="4" label="Sequence Number" minValue="1" increment="1">Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1), otherwise set to 0. Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted.</param>
+        <param index="5" reserved="true" default="NaN"/>
+        <param index="6" reserved="true" default="NaN"/>
+        <param index="7" reserved="true" default="NaN"/>
       </entry>
       <entry value="2001" name="MAV_CMD_IMAGE_STOP_CAPTURE" hasLocation="false" isDestination="false">
         <description>Stop image capture sequence Use NaN for reserved values.</description>

minimal/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Wed Sep 16 2020"
+#define MAVLINK_BUILD_DATE "Thu Sep 17 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 22
  

standard/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Wed Sep 16 2020"
+#define MAVLINK_BUILD_DATE "Thu Sep 17 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

test/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Wed Sep 16 2020"
+#define MAVLINK_BUILD_DATE "Thu Sep 17 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 179
  

uAvionix/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Wed Sep 16 2020"
+#define MAVLINK_BUILD_DATE "Thu Sep 17 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255