autogenerated headers for rev...

autogenerated headers for rev https://github.com/mavlink/mavlink/tree/4f0599109e5dac8efb5e6374081cd0094722f40e

ASLUAV/ASLUAV.h

@@ -112,7 +112,7 @@ typedef enum MAV_CMD
    MAV_CMD_DO_LAST=240, /* NOP - This command is only used to mark the upper limit of the DO commands in the enumeration |Empty| Empty| Empty| Empty| Empty| Empty| Empty|  */
    MAV_CMD_PREFLIGHT_CALIBRATION=241, /* Trigger calibration. This command will be only accepted if in pre-flight mode. Except for Temperature Calibration, only one sensor should be set in a single message and all others should be zero. |1: gyro calibration, 3: gyro temperature calibration| 1: magnetometer calibration| 1: ground pressure calibration| 1: radio RC calibration, 2: RC trim calibration| 1: accelerometer calibration, 2: board level calibration, 3: accelerometer temperature calibration, 4: simple accelerometer calibration| 1: APM: compass/motor interference calibration (PX4: airspeed calibration, deprecated), 2: airspeed calibration| 1: ESC calibration, 3: barometer temperature calibration|  */
    MAV_CMD_PREFLIGHT_SET_SENSOR_OFFSETS=242, /* Set sensor offsets. This command will be only accepted if in pre-flight mode. |Sensor to adjust the offsets for: 0: gyros, 1: accelerometer, 2: magnetometer, 3: barometer, 4: optical flow, 5: second magnetometer, 6: third magnetometer| X axis offset (or generic dimension 1), in the sensor's raw units| Y axis offset (or generic dimension 2), in the sensor's raw units| Z axis offset (or generic dimension 3), in the sensor's raw units| Generic dimension 4, in the sensor's raw units| Generic dimension 5, in the sensor's raw units| Generic dimension 6, in the sensor's raw units|  */
-   MAV_CMD_PREFLIGHT_UAVCAN=243, /* Trigger UAVCAN config. This command will be only accepted if in pre-flight mode. |1: Trigger actuator ID assignment and direction mapping.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
+   MAV_CMD_PREFLIGHT_UAVCAN=243, /* Trigger UAVCAN configuration (actuator ID assignment and direction mapping). Note that this maps to the legacy UAVCAN v0 function UAVCAN_ENUMERATE, which is intended to be executed just once during initial vehicle configuration (it is not a normal pre-flight command and has been poorly named). |1: Trigger actuator ID assignment and direction mapping. 0: Cancel command.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
    MAV_CMD_PREFLIGHT_STORAGE=245, /* Request storage of different parameter values and logs. This command will be only accepted if in pre-flight mode. |Parameter storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM, 2: Reset to defaults| Mission storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM, 2: Reset to defaults| Onboard logging: 0: Ignore, 1: Start default rate logging, -1: Stop logging, > 1: logging rate (e.g. set to 1000 for 1000 Hz logging)| Reserved| Empty| Empty| Empty|  */
    MAV_CMD_PREFLIGHT_REBOOT_SHUTDOWN=246, /* Request the reboot or shutdown of system components. |0: Do nothing for autopilot, 1: Reboot autopilot, 2: Shutdown autopilot, 3: Reboot autopilot and keep it in the bootloader until upgraded.| 0: Do nothing for onboard computer, 1: Reboot onboard computer, 2: Shutdown onboard computer, 3: Reboot onboard computer and keep it in the bootloader until upgraded.| WIP: 0: Do nothing for camera, 1: Reboot onboard camera, 2: Shutdown onboard camera, 3: Reboot onboard camera and keep it in the bootloader until upgraded| WIP: 0: Do nothing for mount (e.g. gimbal), 1: Reboot mount, 2: Shutdown mount, 3: Reboot mount and keep it in the bootloader until upgraded| Reserved (set to 0)| Reserved (set to 0)| WIP: ID (e.g. camera ID -1 for all IDs)|  */
    MAV_CMD_DO_UPGRADE=247, /* Request a target system to start an upgrade of one (or all) of its components. For example, the command might be sent to a companion computer to cause it to upgrade a connected flight controller. The system doing the upgrade will report progress using the normal command protocol sequence for a long running operation. Command protocol information: https://mavlink.io/en/services/command.html. |Component id of the component to be upgraded. If set to 0, all components should be upgraded.| 0: Do not reboot component after the action is executed, 1: Reboot component after the action is executed.| Reserved| Reserved| Reserved| Reserved| WIP: upgrade progress report rate (can be used for more granular control).|  */

ASLUAV/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Sep 11 2020"
+#define MAVLINK_BUILD_DATE "Wed Sep 16 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

ardupilotmega/ardupilotmega.h

@@ -132,7 +132,7 @@ typedef enum MAV_CMD
    MAV_CMD_DO_LAST=240, /* NOP - This command is only used to mark the upper limit of the DO commands in the enumeration |Empty| Empty| Empty| Empty| Empty| Empty| Empty|  */
    MAV_CMD_PREFLIGHT_CALIBRATION=241, /* Trigger calibration. This command will be only accepted if in pre-flight mode. Except for Temperature Calibration, only one sensor should be set in a single message and all others should be zero. |1: gyro calibration, 3: gyro temperature calibration| 1: magnetometer calibration| 1: ground pressure calibration| 1: radio RC calibration, 2: RC trim calibration| 1: accelerometer calibration, 2: board level calibration, 3: accelerometer temperature calibration, 4: simple accelerometer calibration| 1: APM: compass/motor interference calibration (PX4: airspeed calibration, deprecated), 2: airspeed calibration| 1: ESC calibration, 3: barometer temperature calibration|  */
    MAV_CMD_PREFLIGHT_SET_SENSOR_OFFSETS=242, /* Set sensor offsets. This command will be only accepted if in pre-flight mode. |Sensor to adjust the offsets for: 0: gyros, 1: accelerometer, 2: magnetometer, 3: barometer, 4: optical flow, 5: second magnetometer, 6: third magnetometer| X axis offset (or generic dimension 1), in the sensor's raw units| Y axis offset (or generic dimension 2), in the sensor's raw units| Z axis offset (or generic dimension 3), in the sensor's raw units| Generic dimension 4, in the sensor's raw units| Generic dimension 5, in the sensor's raw units| Generic dimension 6, in the sensor's raw units|  */
-   MAV_CMD_PREFLIGHT_UAVCAN=243, /* Trigger UAVCAN config. This command will be only accepted if in pre-flight mode. |1: Trigger actuator ID assignment and direction mapping.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
+   MAV_CMD_PREFLIGHT_UAVCAN=243, /* Trigger UAVCAN configuration (actuator ID assignment and direction mapping). Note that this maps to the legacy UAVCAN v0 function UAVCAN_ENUMERATE, which is intended to be executed just once during initial vehicle configuration (it is not a normal pre-flight command and has been poorly named). |1: Trigger actuator ID assignment and direction mapping. 0: Cancel command.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
    MAV_CMD_PREFLIGHT_STORAGE=245, /* Request storage of different parameter values and logs. This command will be only accepted if in pre-flight mode. |Parameter storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM, 2: Reset to defaults| Mission storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM, 2: Reset to defaults| Onboard logging: 0: Ignore, 1: Start default rate logging, -1: Stop logging, > 1: logging rate (e.g. set to 1000 for 1000 Hz logging)| Reserved| Empty| Empty| Empty|  */
    MAV_CMD_PREFLIGHT_REBOOT_SHUTDOWN=246, /* Request the reboot or shutdown of system components. |0: Do nothing for autopilot, 1: Reboot autopilot, 2: Shutdown autopilot, 3: Reboot autopilot and keep it in the bootloader until upgraded.| 0: Do nothing for onboard computer, 1: Reboot onboard computer, 2: Shutdown onboard computer, 3: Reboot onboard computer and keep it in the bootloader until upgraded.| WIP: 0: Do nothing for camera, 1: Reboot onboard camera, 2: Shutdown onboard camera, 3: Reboot onboard camera and keep it in the bootloader until upgraded| WIP: 0: Do nothing for mount (e.g. gimbal), 1: Reboot mount, 2: Shutdown mount, 3: Reboot mount and keep it in the bootloader until upgraded| Reserved (set to 0)| Reserved (set to 0)| WIP: ID (e.g. camera ID -1 for all IDs)|  */
    MAV_CMD_DO_UPGRADE=247, /* Request a target system to start an upgrade of one (or all) of its components. For example, the command might be sent to a companion computer to cause it to upgrade a connected flight controller. The system doing the upgrade will report progress using the normal command protocol sequence for a long running operation. Command protocol information: https://mavlink.io/en/services/command.html. |Component id of the component to be upgraded. If set to 0, all components should be upgraded.| 0: Do not reboot component after the action is executed, 1: Reboot component after the action is executed.| Reserved| Reserved| Reserved| Reserved| WIP: upgrade progress report rate (can be used for more granular control).|  */

ardupilotmega/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Sep 11 2020"
+#define MAVLINK_BUILD_DATE "Wed Sep 16 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

autoquad/autoquad.h

@@ -156,7 +156,7 @@ typedef enum MAV_CMD
    MAV_CMD_DO_LAST=240, /* NOP - This command is only used to mark the upper limit of the DO commands in the enumeration |Empty| Empty| Empty| Empty| Empty| Empty| Empty|  */
    MAV_CMD_PREFLIGHT_CALIBRATION=241, /* Trigger calibration. This command will be only accepted if in pre-flight mode. Except for Temperature Calibration, only one sensor should be set in a single message and all others should be zero. |1: gyro calibration, 3: gyro temperature calibration| 1: magnetometer calibration| 1: ground pressure calibration| 1: radio RC calibration, 2: RC trim calibration| 1: accelerometer calibration, 2: board level calibration, 3: accelerometer temperature calibration, 4: simple accelerometer calibration| 1: APM: compass/motor interference calibration (PX4: airspeed calibration, deprecated), 2: airspeed calibration| 1: ESC calibration, 3: barometer temperature calibration|  */
    MAV_CMD_PREFLIGHT_SET_SENSOR_OFFSETS=242, /* Set sensor offsets. This command will be only accepted if in pre-flight mode. |Sensor to adjust the offsets for: 0: gyros, 1: accelerometer, 2: magnetometer, 3: barometer, 4: optical flow, 5: second magnetometer, 6: third magnetometer| X axis offset (or generic dimension 1), in the sensor's raw units| Y axis offset (or generic dimension 2), in the sensor's raw units| Z axis offset (or generic dimension 3), in the sensor's raw units| Generic dimension 4, in the sensor's raw units| Generic dimension 5, in the sensor's raw units| Generic dimension 6, in the sensor's raw units|  */
-   MAV_CMD_PREFLIGHT_UAVCAN=243, /* Trigger UAVCAN config. This command will be only accepted if in pre-flight mode. |1: Trigger actuator ID assignment and direction mapping.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
+   MAV_CMD_PREFLIGHT_UAVCAN=243, /* Trigger UAVCAN configuration (actuator ID assignment and direction mapping). Note that this maps to the legacy UAVCAN v0 function UAVCAN_ENUMERATE, which is intended to be executed just once during initial vehicle configuration (it is not a normal pre-flight command and has been poorly named). |1: Trigger actuator ID assignment and direction mapping. 0: Cancel command.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
    MAV_CMD_PREFLIGHT_STORAGE=245, /* Request storage of different parameter values and logs. This command will be only accepted if in pre-flight mode. |Parameter storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM, 2: Reset to defaults| Mission storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM, 2: Reset to defaults| Onboard logging: 0: Ignore, 1: Start default rate logging, -1: Stop logging, > 1: logging rate (e.g. set to 1000 for 1000 Hz logging)| Reserved| Empty| Empty| Empty|  */
    MAV_CMD_PREFLIGHT_REBOOT_SHUTDOWN=246, /* Request the reboot or shutdown of system components. |0: Do nothing for autopilot, 1: Reboot autopilot, 2: Shutdown autopilot, 3: Reboot autopilot and keep it in the bootloader until upgraded.| 0: Do nothing for onboard computer, 1: Reboot onboard computer, 2: Shutdown onboard computer, 3: Reboot onboard computer and keep it in the bootloader until upgraded.| WIP: 0: Do nothing for camera, 1: Reboot onboard camera, 2: Shutdown onboard camera, 3: Reboot onboard camera and keep it in the bootloader until upgraded| WIP: 0: Do nothing for mount (e.g. gimbal), 1: Reboot mount, 2: Shutdown mount, 3: Reboot mount and keep it in the bootloader until upgraded| Reserved (set to 0)| Reserved (set to 0)| WIP: ID (e.g. camera ID -1 for all IDs)|  */
    MAV_CMD_DO_UPGRADE=247, /* Request a target system to start an upgrade of one (or all) of its components. For example, the command might be sent to a companion computer to cause it to upgrade a connected flight controller. The system doing the upgrade will report progress using the normal command protocol sequence for a long running operation. Command protocol information: https://mavlink.io/en/services/command.html. |Component id of the component to be upgraded. If set to 0, all components should be upgraded.| 0: Do not reboot component after the action is executed, 1: Reboot component after the action is executed.| Reserved| Reserved| Reserved| Reserved| WIP: upgrade progress report rate (can be used for more granular control).|  */

autoquad/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Sep 11 2020"
+#define MAVLINK_BUILD_DATE "Wed Sep 16 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

common/common.h

@@ -605,7 +605,7 @@ typedef enum MAV_CMD
    MAV_CMD_DO_LAST=240, /* NOP - This command is only used to mark the upper limit of the DO commands in the enumeration |Empty| Empty| Empty| Empty| Empty| Empty| Empty|  */
    MAV_CMD_PREFLIGHT_CALIBRATION=241, /* Trigger calibration. This command will be only accepted if in pre-flight mode. Except for Temperature Calibration, only one sensor should be set in a single message and all others should be zero. |1: gyro calibration, 3: gyro temperature calibration| 1: magnetometer calibration| 1: ground pressure calibration| 1: radio RC calibration, 2: RC trim calibration| 1: accelerometer calibration, 2: board level calibration, 3: accelerometer temperature calibration, 4: simple accelerometer calibration| 1: APM: compass/motor interference calibration (PX4: airspeed calibration, deprecated), 2: airspeed calibration| 1: ESC calibration, 3: barometer temperature calibration|  */
    MAV_CMD_PREFLIGHT_SET_SENSOR_OFFSETS=242, /* Set sensor offsets. This command will be only accepted if in pre-flight mode. |Sensor to adjust the offsets for: 0: gyros, 1: accelerometer, 2: magnetometer, 3: barometer, 4: optical flow, 5: second magnetometer, 6: third magnetometer| X axis offset (or generic dimension 1), in the sensor's raw units| Y axis offset (or generic dimension 2), in the sensor's raw units| Z axis offset (or generic dimension 3), in the sensor's raw units| Generic dimension 4, in the sensor's raw units| Generic dimension 5, in the sensor's raw units| Generic dimension 6, in the sensor's raw units|  */
-   MAV_CMD_PREFLIGHT_UAVCAN=243, /* Trigger UAVCAN config. This command will be only accepted if in pre-flight mode. |1: Trigger actuator ID assignment and direction mapping.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
+   MAV_CMD_PREFLIGHT_UAVCAN=243, /* Trigger UAVCAN configuration (actuator ID assignment and direction mapping). Note that this maps to the legacy UAVCAN v0 function UAVCAN_ENUMERATE, which is intended to be executed just once during initial vehicle configuration (it is not a normal pre-flight command and has been poorly named). |1: Trigger actuator ID assignment and direction mapping. 0: Cancel command.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
    MAV_CMD_PREFLIGHT_STORAGE=245, /* Request storage of different parameter values and logs. This command will be only accepted if in pre-flight mode. |Parameter storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM, 2: Reset to defaults| Mission storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM, 2: Reset to defaults| Onboard logging: 0: Ignore, 1: Start default rate logging, -1: Stop logging, > 1: logging rate (e.g. set to 1000 for 1000 Hz logging)| Reserved| Empty| Empty| Empty|  */
    MAV_CMD_PREFLIGHT_REBOOT_SHUTDOWN=246, /* Request the reboot or shutdown of system components. |0: Do nothing for autopilot, 1: Reboot autopilot, 2: Shutdown autopilot, 3: Reboot autopilot and keep it in the bootloader until upgraded.| 0: Do nothing for onboard computer, 1: Reboot onboard computer, 2: Shutdown onboard computer, 3: Reboot onboard computer and keep it in the bootloader until upgraded.| WIP: 0: Do nothing for camera, 1: Reboot onboard camera, 2: Shutdown onboard camera, 3: Reboot onboard camera and keep it in the bootloader until upgraded| WIP: 0: Do nothing for mount (e.g. gimbal), 1: Reboot mount, 2: Shutdown mount, 3: Reboot mount and keep it in the bootloader until upgraded| Reserved (set to 0)| Reserved (set to 0)| WIP: ID (e.g. camera ID -1 for all IDs)|  */
    MAV_CMD_DO_UPGRADE=247, /* Request a target system to start an upgrade of one (or all) of its components. For example, the command might be sent to a companion computer to cause it to upgrade a connected flight controller. The system doing the upgrade will report progress using the normal command protocol sequence for a long running operation. Command protocol information: https://mavlink.io/en/services/command.html. |Component id of the component to be upgraded. If set to 0, all components should be upgraded.| 0: Do not reboot component after the action is executed, 1: Reboot component after the action is executed.| Reserved| Reserved| Reserved| Reserved| WIP: upgrade progress report rate (can be used for more granular control).|  */

common/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Sep 11 2020"
+#define MAVLINK_BUILD_DATE "Wed Sep 16 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

icarous/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Sep 11 2020"
+#define MAVLINK_BUILD_DATE "Wed Sep 16 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 46
  

matrixpilot/matrixpilot.h

@@ -129,7 +129,7 @@ typedef enum MAV_CMD
    MAV_CMD_DO_LAST=240, /* NOP - This command is only used to mark the upper limit of the DO commands in the enumeration |Empty| Empty| Empty| Empty| Empty| Empty| Empty|  */
    MAV_CMD_PREFLIGHT_CALIBRATION=241, /* Trigger calibration. This command will be only accepted if in pre-flight mode. Except for Temperature Calibration, only one sensor should be set in a single message and all others should be zero. |1: gyro calibration, 3: gyro temperature calibration| 1: magnetometer calibration| 1: ground pressure calibration| 1: radio RC calibration, 2: RC trim calibration| 1: accelerometer calibration, 2: board level calibration, 3: accelerometer temperature calibration, 4: simple accelerometer calibration| 1: APM: compass/motor interference calibration (PX4: airspeed calibration, deprecated), 2: airspeed calibration| 1: ESC calibration, 3: barometer temperature calibration|  */
    MAV_CMD_PREFLIGHT_SET_SENSOR_OFFSETS=242, /* Set sensor offsets. This command will be only accepted if in pre-flight mode. |Sensor to adjust the offsets for: 0: gyros, 1: accelerometer, 2: magnetometer, 3: barometer, 4: optical flow, 5: second magnetometer, 6: third magnetometer| X axis offset (or generic dimension 1), in the sensor's raw units| Y axis offset (or generic dimension 2), in the sensor's raw units| Z axis offset (or generic dimension 3), in the sensor's raw units| Generic dimension 4, in the sensor's raw units| Generic dimension 5, in the sensor's raw units| Generic dimension 6, in the sensor's raw units|  */
-   MAV_CMD_PREFLIGHT_UAVCAN=243, /* Trigger UAVCAN config. This command will be only accepted if in pre-flight mode. |1: Trigger actuator ID assignment and direction mapping.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
+   MAV_CMD_PREFLIGHT_UAVCAN=243, /* Trigger UAVCAN configuration (actuator ID assignment and direction mapping). Note that this maps to the legacy UAVCAN v0 function UAVCAN_ENUMERATE, which is intended to be executed just once during initial vehicle configuration (it is not a normal pre-flight command and has been poorly named). |1: Trigger actuator ID assignment and direction mapping. 0: Cancel command.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
    MAV_CMD_PREFLIGHT_STORAGE=245, /* Request storage of different parameter values and logs. This command will be only accepted if in pre-flight mode. |Parameter storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM, 2: Reset to defaults| Mission storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM, 2: Reset to defaults| Onboard logging: 0: Ignore, 1: Start default rate logging, -1: Stop logging, > 1: logging rate (e.g. set to 1000 for 1000 Hz logging)| Reserved| Empty| Empty| Empty|  */
    MAV_CMD_PREFLIGHT_REBOOT_SHUTDOWN=246, /* Request the reboot or shutdown of system components. |0: Do nothing for autopilot, 1: Reboot autopilot, 2: Shutdown autopilot, 3: Reboot autopilot and keep it in the bootloader until upgraded.| 0: Do nothing for onboard computer, 1: Reboot onboard computer, 2: Shutdown onboard computer, 3: Reboot onboard computer and keep it in the bootloader until upgraded.| WIP: 0: Do nothing for camera, 1: Reboot onboard camera, 2: Shutdown onboard camera, 3: Reboot onboard camera and keep it in the bootloader until upgraded| WIP: 0: Do nothing for mount (e.g. gimbal), 1: Reboot mount, 2: Shutdown mount, 3: Reboot mount and keep it in the bootloader until upgraded| Reserved (set to 0)| Reserved (set to 0)| WIP: ID (e.g. camera ID -1 for all IDs)|  */
    MAV_CMD_DO_UPGRADE=247, /* Request a target system to start an upgrade of one (or all) of its components. For example, the command might be sent to a companion computer to cause it to upgrade a connected flight controller. The system doing the upgrade will report progress using the normal command protocol sequence for a long running operation. Command protocol information: https://mavlink.io/en/services/command.html. |Component id of the component to be upgraded. If set to 0, all components should be upgraded.| 0: Do not reboot component after the action is executed, 1: Reboot component after the action is executed.| Reserved| Reserved| Reserved| Reserved| WIP: upgrade progress report rate (can be used for more granular control).|  */

matrixpilot/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Sep 11 2020"
+#define MAVLINK_BUILD_DATE "Wed Sep 16 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

message_definitions/common.xml

@@ -1527,8 +1527,8 @@
         <param index="7" label="6th Dimension">Generic dimension 6, in the sensor's raw units</param>
       </entry>
       <entry value="243" name="MAV_CMD_PREFLIGHT_UAVCAN" hasLocation="false" isDestination="false">
-        <description>Trigger UAVCAN config. This command will be only accepted if in pre-flight mode.</description>
-        <param index="1" label="Actuator ID">1: Trigger actuator ID assignment and direction mapping.</param>
+        <description>Trigger UAVCAN configuration (actuator ID assignment and direction mapping). Note that this maps to the legacy UAVCAN v0 function UAVCAN_ENUMERATE, which is intended to be executed just once during initial vehicle configuration (it is not a normal pre-flight command and has been poorly named).</description>
+        <param index="1" label="Actuator ID">1: Trigger actuator ID assignment and direction mapping. 0: Cancel command.</param>
         <param index="2">Reserved</param>
         <param index="3">Reserved</param>
         <param index="4">Reserved</param>

minimal/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Sep 11 2020"
+#define MAVLINK_BUILD_DATE "Wed Sep 16 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 22
  

standard/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Sep 11 2020"
+#define MAVLINK_BUILD_DATE "Wed Sep 16 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

test/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Sep 11 2020"
+#define MAVLINK_BUILD_DATE "Wed Sep 16 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 179
  

uAvionix/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Sep 11 2020"
+#define MAVLINK_BUILD_DATE "Wed Sep 16 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255