autogenerated headers for rev...

autogenerated headers for rev https://github.com/mavlink/mavlink/tree/4cc25bb0f238473cdd6d12990302538ee7f3c68d

autogenerated headers for rev...
autogenerated headers for rev https://github.com/mavlink/mavlink/tree/4cc25bb0f238473cdd6d12990302538ee7f3c68d
fd29ec19 · PX4BuildBot · 2148dde1 · fd29ec19 · fd29ec19 · fd29ec19
Commit fd29ec19 authored Aug 08, 2019 by PX4BuildBot
18 changed files
--- a/ASLUAV/ASLUAV.h
+++ b/ASLUAV/ASLUAV.h
@@ -117,8 +117,8 @@ typedef enum MAV_CMD
   MAV_CMD_COMPONENT_ARM_DISARM=400, /* Arms / Disarms a component |0: disarm, 1: arm| 0: only arm-disarm when landed, 21196: enforce arming/disarming even in-air (during flight)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_GET_HOME_POSITION=410, /* Request the home position from the vehicle. |Reserved| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
   MAV_CMD_START_RX_PAIR=500, /* Starts receiver pairing. |0:Spektrum.| RC type.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
-   MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
-   MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM |The MAVLink message ID| The interval between two messages. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID. The receiver should ACK the command and then emit its response in a MESSAGE_INTERVAL message. |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM. |The MAVLink message ID| s. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES=520, /* Request autopilot capabilities. The receiver should ACK the command and then emit its capabilities in an AUTOPILOT_VERSION message |1: Request autopilot version| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
@@ -134,10 +134,10 @@ typedef enum MAV_CMD
   MAV_CMD_SET_CAMERA_FOCUS=532, /* Set camera focus. Camera must respond with a CAMERA_SETTINGS message (on success). Use NaN for reserved values. |Focus type| Focus value| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_JUMP_TAG=600, /* Tagged jump target. Can be jumped to with MAV_CMD_DO_JUMP_TAG. |Tag.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_DO_JUMP_TAG=601, /* Jump to the matching tag in the mission list. Repeat this action for the specified number of times. A mission should contain a single matching tag for each jump. If this is not the case then a jump to a missing tag should complete the mission, and a jump where there are multiple matching tags should always select the one with the lowest mission sequence number. |Target tag to jump to.| Repeat count.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
-   MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| end on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_IMAGE_STOP_CAPTURE=2001, /* Stop image capture sequence Use NaN for reserved values. |Reserved (Set to 0)| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_REQUEST_CAMERA_IMAGE_CAPTURE=2002, /* Re-request a CAMERA_IMAGE_CAPTURE message. Use NaN for reserved values. |Sequence number for missing CAMERA_IMAGE_CAPTURE message| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
-   MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| e camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| 1 to pause triggering, but without switching the camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_VIDEO_START_CAPTURE=2500, /* Starts video capture (recording). Use NaN for reserved values. |Video Stream ID (0 for all streams)| Frequency CAMERA_CAPTURE_STATUS messages should be sent while recording (0 for no messages, otherwise frequency)| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_VIDEO_STOP_CAPTURE=2501, /* Stop the current video capture (recording). Use NaN for reserved values. |Video Stream ID (0 for all streams)| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_VIDEO_START_STREAMING=2502, /* Start video streaming |Video Stream ID (0 for all streams, 1 for first, 2 for second, etc.)| Reserved| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
@@ -148,7 +148,7 @@ typedef enum MAV_CMD
   MAV_CMD_LOGGING_STOP=2511, /* Request to stop streaming log data over MAVLink |Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)|  */
   MAV_CMD_AIRFRAME_CONFIGURATION=2520, /*  |Landing gear ID (default: 0, -1 for all)| Landing gear position (Down: 0, Up: 1, NaN for no change)| Reserved, set to NaN| Reserved, set to NaN| Reserved, set to NaN| Reserved, set to NaN| Reserved, set to NaN|  */
   MAV_CMD_CONTROL_HIGH_LATENCY=2600, /* Request to start/stop transmitting over the high latency telemetry |Control transmission over high latency telemetry (0: stop, 1: start)| Empty| Empty| Empty| Empty| Empty| Empty|  */
-   MAV_CMD_PANORAMA_CREATE=2800, /* Create a panorama at the current position |Viewing angle horizontal of the panorama (+- 0.5 the total angle)| cal of panorama.| Speed of the horizontal rotation.| Speed of the vertical rotation.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_PANORAMA_CREATE=2800, /* Create a panorama at the current position |l angle)| Viewing angle vertical of panorama.| Speed of the horizontal rotation.| Speed of the vertical rotation.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_DO_VTOL_TRANSITION=3000, /* Request VTOL transition |The target VTOL state. Only MAV_VTOL_STATE_MC and MAV_VTOL_STATE_FW can be used.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_ARM_AUTHORIZATION_REQUEST=3001, /* Request authorization to arm the vehicle to a external entity, the arm authorizer is responsible to request all data that is needs from the vehicle before authorize or deny the request. If approved the progress of command_ack message should be set with period of time that this authorization is valid in seconds or in case it was denied it should be set with one of the reasons in ARM_AUTH_DENIED_REASON.
         |Vehicle system id, this way ground station can request arm authorization on behalf of any vehicle| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
@@ -171,7 +171,7 @@ typedef enum MAV_CMD
         |Reserved| Reserved| Reserved| Reserved| Latitude| Longitude| Altitude|  */
   MAV_CMD_UAVCAN_GET_NODE_INFO=5200, /* Commands the vehicle to respond with a sequence of messages UAVCAN_NODE_INFO, one message per every UAVCAN node that is online. Note that some of the response messages can be lost, which the receiver can detect easily by checking whether every received UAVCAN_NODE_STATUS has a matching message UAVCAN_NODE_INFO received earlier; if not, this command should be sent again in order to request re-transmission of the node information messages. |Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)|  */
   MAV_CMD_PAYLOAD_PREPARE_DEPLOY=30001, /* Deploy payload on a Lat / Lon / Alt position. This includes the navigation to reach the required release position and velocity. |Operation mode. 0: prepare single payload deploy (overwriting previous requests), but do not execute it. 1: execute payload deploy immediately (rejecting further deploy commands during execution, but allowing abort). 2: add payload deploy to existing deployment list.| Desired approach vector in compass heading. A negative value indicates the system can define the approach vector at will.| Desired ground speed at release time. This can be overridden by the airframe in case it needs to meet minimum airspeed. A negative value indicates the system can define the ground speed at will.| Minimum altitude clearance to the release position. A negative value indicates the system can define the clearance at will.| Latitude unscaled for MISSION_ITEM or in 1e7 degrees for MISSION_ITEM_INT| Longitude unscaled for MISSION_ITEM or in 1e7 degrees for MISSION_ITEM_INT| Altitude (MSL), in meters|  */
-   MAV_CMD_PAYLOAD_CONTROL_DEPLOY=30002, /* Control the payload deployment. |Operation mode. 0: Abort deployment, continue normal mission. 1: switch to payload deployment mode. 100: delete first payload deployment request. 101: delete all payload deployment requests.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
+   MAV_CMD_PAYLOAD_CONTROL_DEPLOY=30002, /* Control the payload deployment. |payload deployment request. 101: delete all payload deployment requests.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
   MAV_CMD_WAYPOINT_USER_1=31000, /* User defined waypoint item. Ground Station will show the Vehicle as flying through this item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude (MSL), in meters|  */
   MAV_CMD_WAYPOINT_USER_2=31001, /* User defined waypoint item. Ground Station will show the Vehicle as flying through this item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude (MSL), in meters|  */
   MAV_CMD_WAYPOINT_USER_3=31002, /* User defined waypoint item. Ground Station will show the Vehicle as flying through this item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude (MSL), in meters|  */

--- a/ASLUAV/version.h
+++ b/ASLUAV/version.h
@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H

-#define MAVLINK_BUILD_DATE "Wed Aug 07 2019"
+#define MAVLINK_BUILD_DATE "Thu Aug 08 2019"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
 

--- a/ardupilotmega/ardupilotmega.h
+++ b/ardupilotmega/ardupilotmega.h
@@ -137,8 +137,8 @@ typedef enum MAV_CMD
   MAV_CMD_COMPONENT_ARM_DISARM=400, /* Arms / Disarms a component |0: disarm, 1: arm| 0: only arm-disarm when landed, 21196: enforce arming/disarming even in-air (during flight)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_GET_HOME_POSITION=410, /* Request the home position from the vehicle. |Reserved| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
   MAV_CMD_START_RX_PAIR=500, /* Starts receiver pairing. |0:Spektrum.| RC type.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
-   MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
-   MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM |The MAVLink message ID| The interval between two messages. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID. The receiver should ACK the command and then emit its response in a MESSAGE_INTERVAL message. |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM. |The MAVLink message ID| s. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES=520, /* Request autopilot capabilities. The receiver should ACK the command and then emit its capabilities in an AUTOPILOT_VERSION message |1: Request autopilot version| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
@@ -154,10 +154,10 @@ typedef enum MAV_CMD
   MAV_CMD_SET_CAMERA_FOCUS=532, /* Set camera focus. Camera must respond with a CAMERA_SETTINGS message (on success). Use NaN for reserved values. |Focus type| Focus value| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_JUMP_TAG=600, /* Tagged jump target. Can be jumped to with MAV_CMD_DO_JUMP_TAG. |Tag.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_DO_JUMP_TAG=601, /* Jump to the matching tag in the mission list. Repeat this action for the specified number of times. A mission should contain a single matching tag for each jump. If this is not the case then a jump to a missing tag should complete the mission, and a jump where there are multiple matching tags should always select the one with the lowest mission sequence number. |Target tag to jump to.| Repeat count.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
-   MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| end on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_IMAGE_STOP_CAPTURE=2001, /* Stop image capture sequence Use NaN for reserved values. |Reserved (Set to 0)| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_REQUEST_CAMERA_IMAGE_CAPTURE=2002, /* Re-request a CAMERA_IMAGE_CAPTURE message. Use NaN for reserved values. |Sequence number for missing CAMERA_IMAGE_CAPTURE message| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
-   MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| e camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| 1 to pause triggering, but without switching the camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_VIDEO_START_CAPTURE=2500, /* Starts video capture (recording). Use NaN for reserved values. |Video Stream ID (0 for all streams)| Frequency CAMERA_CAPTURE_STATUS messages should be sent while recording (0 for no messages, otherwise frequency)| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_VIDEO_STOP_CAPTURE=2501, /* Stop the current video capture (recording). Use NaN for reserved values. |Video Stream ID (0 for all streams)| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_VIDEO_START_STREAMING=2502, /* Start video streaming |Video Stream ID (0 for all streams, 1 for first, 2 for second, etc.)| Reserved| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
@@ -168,7 +168,7 @@ typedef enum MAV_CMD
   MAV_CMD_LOGGING_STOP=2511, /* Request to stop streaming log data over MAVLink |Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)|  */
   MAV_CMD_AIRFRAME_CONFIGURATION=2520, /*  |Landing gear ID (default: 0, -1 for all)| Landing gear position (Down: 0, Up: 1, NaN for no change)| Reserved, set to NaN| Reserved, set to NaN| Reserved, set to NaN| Reserved, set to NaN| Reserved, set to NaN|  */
   MAV_CMD_CONTROL_HIGH_LATENCY=2600, /* Request to start/stop transmitting over the high latency telemetry |Control transmission over high latency telemetry (0: stop, 1: start)| Empty| Empty| Empty| Empty| Empty| Empty|  */
-   MAV_CMD_PANORAMA_CREATE=2800, /* Create a panorama at the current position |Viewing angle horizontal of the panorama (+- 0.5 the total angle)| cal of panorama.| Speed of the horizontal rotation.| Speed of the vertical rotation.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_PANORAMA_CREATE=2800, /* Create a panorama at the current position |l angle)| Viewing angle vertical of panorama.| Speed of the horizontal rotation.| Speed of the vertical rotation.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_DO_VTOL_TRANSITION=3000, /* Request VTOL transition |The target VTOL state. Only MAV_VTOL_STATE_MC and MAV_VTOL_STATE_FW can be used.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_ARM_AUTHORIZATION_REQUEST=3001, /* Request authorization to arm the vehicle to a external entity, the arm authorizer is responsible to request all data that is needs from the vehicle before authorize or deny the request. If approved the progress of command_ack message should be set with period of time that this authorization is valid in seconds or in case it was denied it should be set with one of the reasons in ARM_AUTH_DENIED_REASON.
         |Vehicle system id, this way ground station can request arm authorization on behalf of any vehicle| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
@@ -191,7 +191,7 @@ typedef enum MAV_CMD
         |Reserved| Reserved| Reserved| Reserved| Latitude| Longitude| Altitude|  */
   MAV_CMD_UAVCAN_GET_NODE_INFO=5200, /* Commands the vehicle to respond with a sequence of messages UAVCAN_NODE_INFO, one message per every UAVCAN node that is online. Note that some of the response messages can be lost, which the receiver can detect easily by checking whether every received UAVCAN_NODE_STATUS has a matching message UAVCAN_NODE_INFO received earlier; if not, this command should be sent again in order to request re-transmission of the node information messages. |Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)|  */
   MAV_CMD_PAYLOAD_PREPARE_DEPLOY=30001, /* Deploy payload on a Lat / Lon / Alt position. This includes the navigation to reach the required release position and velocity. |Operation mode. 0: prepare single payload deploy (overwriting previous requests), but do not execute it. 1: execute payload deploy immediately (rejecting further deploy commands during execution, but allowing abort). 2: add payload deploy to existing deployment list.| Desired approach vector in compass heading. A negative value indicates the system can define the approach vector at will.| Desired ground speed at release time. This can be overridden by the airframe in case it needs to meet minimum airspeed. A negative value indicates the system can define the ground speed at will.| Minimum altitude clearance to the release position. A negative value indicates the system can define the clearance at will.| Latitude unscaled for MISSION_ITEM or in 1e7 degrees for MISSION_ITEM_INT| Longitude unscaled for MISSION_ITEM or in 1e7 degrees for MISSION_ITEM_INT| Altitude (MSL), in meters|  */
-   MAV_CMD_PAYLOAD_CONTROL_DEPLOY=30002, /* Control the payload deployment. |Operation mode. 0: Abort deployment, continue normal mission. 1: switch to payload deployment mode. 100: delete first payload deployment request. 101: delete all payload deployment requests.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
+   MAV_CMD_PAYLOAD_CONTROL_DEPLOY=30002, /* Control the payload deployment. |payload deployment request. 101: delete all payload deployment requests.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
   MAV_CMD_WAYPOINT_USER_1=31000, /* User defined waypoint item. Ground Station will show the Vehicle as flying through this item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude (MSL), in meters|  */
   MAV_CMD_WAYPOINT_USER_2=31001, /* User defined waypoint item. Ground Station will show the Vehicle as flying through this item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude (MSL), in meters|  */
   MAV_CMD_WAYPOINT_USER_3=31002, /* User defined waypoint item. Ground Station will show the Vehicle as flying through this item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude (MSL), in meters|  */

--- a/ardupilotmega/version.h
+++ b/ardupilotmega/version.h
@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H

-#define MAVLINK_BUILD_DATE "Wed Aug 07 2019"
+#define MAVLINK_BUILD_DATE "Thu Aug 08 2019"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
 

--- a/autoquad/autoquad.h
+++ b/autoquad/autoquad.h
@@ -161,8 +161,8 @@ typedef enum MAV_CMD
   MAV_CMD_COMPONENT_ARM_DISARM=400, /* Arms / Disarms a component |0: disarm, 1: arm| 0: only arm-disarm when landed, 21196: enforce arming/disarming even in-air (during flight)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_GET_HOME_POSITION=410, /* Request the home position from the vehicle. |Reserved| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
   MAV_CMD_START_RX_PAIR=500, /* Starts receiver pairing. |0:Spektrum.| RC type.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
-   MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
-   MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM |The MAVLink message ID| The interval between two messages. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID. The receiver should ACK the command and then emit its response in a MESSAGE_INTERVAL message. |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM. |The MAVLink message ID| s. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES=520, /* Request autopilot capabilities. The receiver should ACK the command and then emit its capabilities in an AUTOPILOT_VERSION message |1: Request autopilot version| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
@@ -178,10 +178,10 @@ typedef enum MAV_CMD
   MAV_CMD_SET_CAMERA_FOCUS=532, /* Set camera focus. Camera must respond with a CAMERA_SETTINGS message (on success). Use NaN for reserved values. |Focus type| Focus value| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_JUMP_TAG=600, /* Tagged jump target. Can be jumped to with MAV_CMD_DO_JUMP_TAG. |Tag.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_DO_JUMP_TAG=601, /* Jump to the matching tag in the mission list. Repeat this action for the specified number of times. A mission should contain a single matching tag for each jump. If this is not the case then a jump to a missing tag should complete the mission, and a jump where there are multiple matching tags should always select the one with the lowest mission sequence number. |Target tag to jump to.| Repeat count.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
-   MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| end on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_IMAGE_STOP_CAPTURE=2001, /* Stop image capture sequence Use NaN for reserved values. |Reserved (Set to 0)| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_REQUEST_CAMERA_IMAGE_CAPTURE=2002, /* Re-request a CAMERA_IMAGE_CAPTURE message. Use NaN for reserved values. |Sequence number for missing CAMERA_IMAGE_CAPTURE message| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
-   MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| e camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| 1 to pause triggering, but without switching the camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_VIDEO_START_CAPTURE=2500, /* Starts video capture (recording). Use NaN for reserved values. |Video Stream ID (0 for all streams)| Frequency CAMERA_CAPTURE_STATUS messages should be sent while recording (0 for no messages, otherwise frequency)| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_VIDEO_STOP_CAPTURE=2501, /* Stop the current video capture (recording). Use NaN for reserved values. |Video Stream ID (0 for all streams)| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_VIDEO_START_STREAMING=2502, /* Start video streaming |Video Stream ID (0 for all streams, 1 for first, 2 for second, etc.)| Reserved| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
@@ -192,7 +192,7 @@ typedef enum MAV_CMD
   MAV_CMD_LOGGING_STOP=2511, /* Request to stop streaming log data over MAVLink |Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)|  */
   MAV_CMD_AIRFRAME_CONFIGURATION=2520, /*  |Landing gear ID (default: 0, -1 for all)| Landing gear position (Down: 0, Up: 1, NaN for no change)| Reserved, set to NaN| Reserved, set to NaN| Reserved, set to NaN| Reserved, set to NaN| Reserved, set to NaN|  */
   MAV_CMD_CONTROL_HIGH_LATENCY=2600, /* Request to start/stop transmitting over the high latency telemetry |Control transmission over high latency telemetry (0: stop, 1: start)| Empty| Empty| Empty| Empty| Empty| Empty|  */
-   MAV_CMD_PANORAMA_CREATE=2800, /* Create a panorama at the current position |Viewing angle horizontal of the panorama (+- 0.5 the total angle)| cal of panorama.| Speed of the horizontal rotation.| Speed of the vertical rotation.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_PANORAMA_CREATE=2800, /* Create a panorama at the current position |l angle)| Viewing angle vertical of panorama.| Speed of the horizontal rotation.| Speed of the vertical rotation.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_DO_VTOL_TRANSITION=3000, /* Request VTOL transition |The target VTOL state. Only MAV_VTOL_STATE_MC and MAV_VTOL_STATE_FW can be used.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_ARM_AUTHORIZATION_REQUEST=3001, /* Request authorization to arm the vehicle to a external entity, the arm authorizer is responsible to request all data that is needs from the vehicle before authorize or deny the request. If approved the progress of command_ack message should be set with period of time that this authorization is valid in seconds or in case it was denied it should be set with one of the reasons in ARM_AUTH_DENIED_REASON.
         |Vehicle system id, this way ground station can request arm authorization on behalf of any vehicle| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
@@ -215,7 +215,7 @@ typedef enum MAV_CMD
         |Reserved| Reserved| Reserved| Reserved| Latitude| Longitude| Altitude|  */
   MAV_CMD_UAVCAN_GET_NODE_INFO=5200, /* Commands the vehicle to respond with a sequence of messages UAVCAN_NODE_INFO, one message per every UAVCAN node that is online. Note that some of the response messages can be lost, which the receiver can detect easily by checking whether every received UAVCAN_NODE_STATUS has a matching message UAVCAN_NODE_INFO received earlier; if not, this command should be sent again in order to request re-transmission of the node information messages. |Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)|  */
   MAV_CMD_PAYLOAD_PREPARE_DEPLOY=30001, /* Deploy payload on a Lat / Lon / Alt position. This includes the navigation to reach the required release position and velocity. |Operation mode. 0: prepare single payload deploy (overwriting previous requests), but do not execute it. 1: execute payload deploy immediately (rejecting further deploy commands during execution, but allowing abort). 2: add payload deploy to existing deployment list.| Desired approach vector in compass heading. A negative value indicates the system can define the approach vector at will.| Desired ground speed at release time. This can be overridden by the airframe in case it needs to meet minimum airspeed. A negative value indicates the system can define the ground speed at will.| Minimum altitude clearance to the release position. A negative value indicates the system can define the clearance at will.| Latitude unscaled for MISSION_ITEM or in 1e7 degrees for MISSION_ITEM_INT| Longitude unscaled for MISSION_ITEM or in 1e7 degrees for MISSION_ITEM_INT| Altitude (MSL), in meters|  */
-   MAV_CMD_PAYLOAD_CONTROL_DEPLOY=30002, /* Control the payload deployment. |Operation mode. 0: Abort deployment, continue normal mission. 1: switch to payload deployment mode. 100: delete first payload deployment request. 101: delete all payload deployment requests.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
+   MAV_CMD_PAYLOAD_CONTROL_DEPLOY=30002, /* Control the payload deployment. |payload deployment request. 101: delete all payload deployment requests.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
   MAV_CMD_WAYPOINT_USER_1=31000, /* User defined waypoint item. Ground Station will show the Vehicle as flying through this item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude (MSL), in meters|  */
   MAV_CMD_WAYPOINT_USER_2=31001, /* User defined waypoint item. Ground Station will show the Vehicle as flying through this item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude (MSL), in meters|  */
   MAV_CMD_WAYPOINT_USER_3=31002, /* User defined waypoint item. Ground Station will show the Vehicle as flying through this item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude (MSL), in meters|  */

--- a/autoquad/version.h
+++ b/autoquad/version.h
@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H

-#define MAVLINK_BUILD_DATE "Wed Aug 07 2019"
+#define MAVLINK_BUILD_DATE "Thu Aug 08 2019"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
 

--- a/common/common.h
+++ b/common/common.h
@@ -525,8 +525,8 @@ typedef enum MAV_CMD
   MAV_CMD_COMPONENT_ARM_DISARM=400, /* Arms / Disarms a component |0: disarm, 1: arm| 0: only arm-disarm when landed, 21196: enforce arming/disarming even in-air (during flight)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_GET_HOME_POSITION=410, /* Request the home position from the vehicle. |Reserved| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
   MAV_CMD_START_RX_PAIR=500, /* Starts receiver pairing. |0:Spektrum.| RC type.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
-   MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
-   MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM |The MAVLink message ID| The interval between two messages. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID. The receiver should ACK the command and then emit its response in a MESSAGE_INTERVAL message. |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM. |The MAVLink message ID| s. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES=520, /* Request autopilot capabilities. The receiver should ACK the command and then emit its capabilities in an AUTOPILOT_VERSION message |1: Request autopilot version| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
@@ -542,10 +542,10 @@ typedef enum MAV_CMD
   MAV_CMD_SET_CAMERA_FOCUS=532, /* Set camera focus. Camera must respond with a CAMERA_SETTINGS message (on success). Use NaN for reserved values. |Focus type| Focus value| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_JUMP_TAG=600, /* Tagged jump target. Can be jumped to with MAV_CMD_DO_JUMP_TAG. |Tag.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_DO_JUMP_TAG=601, /* Jump to the matching tag in the mission list. Repeat this action for the specified number of times. A mission should contain a single matching tag for each jump. If this is not the case then a jump to a missing tag should complete the mission, and a jump where there are multiple matching tags should always select the one with the lowest mission sequence number. |Target tag to jump to.| Repeat count.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
-   MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| end on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_IMAGE_STOP_CAPTURE=2001, /* Stop image capture sequence Use NaN for reserved values. |Reserved (Set to 0)| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_REQUEST_CAMERA_IMAGE_CAPTURE=2002, /* Re-request a CAMERA_IMAGE_CAPTURE message. Use NaN for reserved values. |Sequence number for missing CAMERA_IMAGE_CAPTURE message| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
-   MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| e camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| 1 to pause triggering, but without switching the camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_VIDEO_START_CAPTURE=2500, /* Starts video capture (recording). Use NaN for reserved values. |Video Stream ID (0 for all streams)| Frequency CAMERA_CAPTURE_STATUS messages should be sent while recording (0 for no messages, otherwise frequency)| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_VIDEO_STOP_CAPTURE=2501, /* Stop the current video capture (recording). Use NaN for reserved values. |Video Stream ID (0 for all streams)| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_VIDEO_START_STREAMING=2502, /* Start video streaming |Video Stream ID (0 for all streams, 1 for first, 2 for second, etc.)| Reserved| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
@@ -556,7 +556,7 @@ typedef enum MAV_CMD
   MAV_CMD_LOGGING_STOP=2511, /* Request to stop streaming log data over MAVLink |Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)|  */
   MAV_CMD_AIRFRAME_CONFIGURATION=2520, /*  |Landing gear ID (default: 0, -1 for all)| Landing gear position (Down: 0, Up: 1, NaN for no change)| Reserved, set to NaN| Reserved, set to NaN| Reserved, set to NaN| Reserved, set to NaN| Reserved, set to NaN|  */
   MAV_CMD_CONTROL_HIGH_LATENCY=2600, /* Request to start/stop transmitting over the high latency telemetry |Control transmission over high latency telemetry (0: stop, 1: start)| Empty| Empty| Empty| Empty| Empty| Empty|  */
-   MAV_CMD_PANORAMA_CREATE=2800, /* Create a panorama at the current position |Viewing angle horizontal of the panorama (+- 0.5 the total angle)| cal of panorama.| Speed of the horizontal rotation.| Speed of the vertical rotation.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_PANORAMA_CREATE=2800, /* Create a panorama at the current position |l angle)| Viewing angle vertical of panorama.| Speed of the horizontal rotation.| Speed of the vertical rotation.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_DO_VTOL_TRANSITION=3000, /* Request VTOL transition |The target VTOL state. Only MAV_VTOL_STATE_MC and MAV_VTOL_STATE_FW can be used.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_ARM_AUTHORIZATION_REQUEST=3001, /* Request authorization to arm the vehicle to a external entity, the arm authorizer is responsible to request all data that is needs from the vehicle before authorize or deny the request. If approved the progress of command_ack message should be set with period of time that this authorization is valid in seconds or in case it was denied it should be set with one of the reasons in ARM_AUTH_DENIED_REASON.
         |Vehicle system id, this way ground station can request arm authorization on behalf of any vehicle| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
@@ -579,7 +579,7 @@ typedef enum MAV_CMD
         |Reserved| Reserved| Reserved| Reserved| Latitude| Longitude| Altitude|  */
   MAV_CMD_UAVCAN_GET_NODE_INFO=5200, /* Commands the vehicle to respond with a sequence of messages UAVCAN_NODE_INFO, one message per every UAVCAN node that is online. Note that some of the response messages can be lost, which the receiver can detect easily by checking whether every received UAVCAN_NODE_STATUS has a matching message UAVCAN_NODE_INFO received earlier; if not, this command should be sent again in order to request re-transmission of the node information messages. |Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)|  */
   MAV_CMD_PAYLOAD_PREPARE_DEPLOY=30001, /* Deploy payload on a Lat / Lon / Alt position. This includes the navigation to reach the required release position and velocity. |Operation mode. 0: prepare single payload deploy (overwriting previous requests), but do not execute it. 1: execute payload deploy immediately (rejecting further deploy commands during execution, but allowing abort). 2: add payload deploy to existing deployment list.| Desired approach vector in compass heading. A negative value indicates the system can define the approach vector at will.| Desired ground speed at release time. This can be overridden by the airframe in case it needs to meet minimum airspeed. A negative value indicates the system can define the ground speed at will.| Minimum altitude clearance to the release position. A negative value indicates the system can define the clearance at will.| Latitude unscaled for MISSION_ITEM or in 1e7 degrees for MISSION_ITEM_INT| Longitude unscaled for MISSION_ITEM or in 1e7 degrees for MISSION_ITEM_INT| Altitude (MSL), in meters|  */
-   MAV_CMD_PAYLOAD_CONTROL_DEPLOY=30002, /* Control the payload deployment. |Operation mode. 0: Abort deployment, continue normal mission. 1: switch to payload deployment mode. 100: delete first payload deployment request. 101: delete all payload deployment requests.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
+   MAV_CMD_PAYLOAD_CONTROL_DEPLOY=30002, /* Control the payload deployment. |payload deployment request. 101: delete all payload deployment requests.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
   MAV_CMD_WAYPOINT_USER_1=31000, /* User defined waypoint item. Ground Station will show the Vehicle as flying through this item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude (MSL), in meters|  */
   MAV_CMD_WAYPOINT_USER_2=31001, /* User defined waypoint item. Ground Station will show the Vehicle as flying through this item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude (MSL), in meters|  */
   MAV_CMD_WAYPOINT_USER_3=31002, /* User defined waypoint item. Ground Station will show the Vehicle as flying through this item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude (MSL), in meters|  */

--- a/common/version.h
+++ b/common/version.h
@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H

-#define MAVLINK_BUILD_DATE "Wed Aug 07 2019"
+#define MAVLINK_BUILD_DATE "Thu Aug 08 2019"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
 

--- a/icarous/version.h
+++ b/icarous/version.h
@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H

-#define MAVLINK_BUILD_DATE "Wed Aug 07 2019"
+#define MAVLINK_BUILD_DATE "Thu Aug 08 2019"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
 

--- a/matrixpilot/matrixpilot.h
+++ b/matrixpilot/matrixpilot.h
@@ -134,8 +134,8 @@ typedef enum MAV_CMD
   MAV_CMD_COMPONENT_ARM_DISARM=400, /* Arms / Disarms a component |0: disarm, 1: arm| 0: only arm-disarm when landed, 21196: enforce arming/disarming even in-air (during flight)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_GET_HOME_POSITION=410, /* Request the home position from the vehicle. |Reserved| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
   MAV_CMD_START_RX_PAIR=500, /* Starts receiver pairing. |0:Spektrum.| RC type.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
-   MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
-   MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM |The MAVLink message ID| The interval between two messages. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID. The receiver should ACK the command and then emit its response in a MESSAGE_INTERVAL message. |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM. |The MAVLink message ID| s. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES=520, /* Request autopilot capabilities. The receiver should ACK the command and then emit its capabilities in an AUTOPILOT_VERSION message |1: Request autopilot version| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
@@ -151,10 +151,10 @@ typedef enum MAV_CMD
   MAV_CMD_SET_CAMERA_FOCUS=532, /* Set camera focus. Camera must respond with a CAMERA_SETTINGS message (on success). Use NaN for reserved values. |Focus type| Focus value| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_JUMP_TAG=600, /* Tagged jump target. Can be jumped to with MAV_CMD_DO_JUMP_TAG. |Tag.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_DO_JUMP_TAG=601, /* Jump to the matching tag in the mission list. Repeat this action for the specified number of times. A mission should contain a single matching tag for each jump. If this is not the case then a jump to a missing tag should complete the mission, and a jump where there are multiple matching tags should always select the one with the lowest mission sequence number. |Target tag to jump to.| Repeat count.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
-   MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| end on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_IMAGE_STOP_CAPTURE=2001, /* Stop image capture sequence Use NaN for reserved values. |Reserved (Set to 0)| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_REQUEST_CAMERA_IMAGE_CAPTURE=2002, /* Re-request a CAMERA_IMAGE_CAPTURE message. Use NaN for reserved values. |Sequence number for missing CAMERA_IMAGE_CAPTURE message| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
-   MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| e camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| 1 to pause triggering, but without switching the camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_VIDEO_START_CAPTURE=2500, /* Starts video capture (recording). Use NaN for reserved values. |Video Stream ID (0 for all streams)| Frequency CAMERA_CAPTURE_STATUS messages should be sent while recording (0 for no messages, otherwise frequency)| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_VIDEO_STOP_CAPTURE=2501, /* Stop the current video capture (recording). Use NaN for reserved values. |Video Stream ID (0 for all streams)| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_VIDEO_START_STREAMING=2502, /* Start video streaming |Video Stream ID (0 for all streams, 1 for first, 2 for second, etc.)| Reserved| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
@@ -165,7 +165,7 @@ typedef enum MAV_CMD
   MAV_CMD_LOGGING_STOP=2511, /* Request to stop streaming log data over MAVLink |Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)|  */
   MAV_CMD_AIRFRAME_CONFIGURATION=2520, /*  |Landing gear ID (default: 0, -1 for all)| Landing gear position (Down: 0, Up: 1, NaN for no change)| Reserved, set to NaN| Reserved, set to NaN| Reserved, set to NaN| Reserved, set to NaN| Reserved, set to NaN|  */
   MAV_CMD_CONTROL_HIGH_LATENCY=2600, /* Request to start/stop transmitting over the high latency telemetry |Control transmission over high latency telemetry (0: stop, 1: start)| Empty| Empty| Empty| Empty| Empty| Empty|  */
-   MAV_CMD_PANORAMA_CREATE=2800, /* Create a panorama at the current position |Viewing angle horizontal of the panorama (+- 0.5 the total angle)| cal of panorama.| Speed of the horizontal rotation.| Speed of the vertical rotation.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_PANORAMA_CREATE=2800, /* Create a panorama at the current position |l angle)| Viewing angle vertical of panorama.| Speed of the horizontal rotation.| Speed of the vertical rotation.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_DO_VTOL_TRANSITION=3000, /* Request VTOL transition |The target VTOL state. Only MAV_VTOL_STATE_MC and MAV_VTOL_STATE_FW can be used.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_ARM_AUTHORIZATION_REQUEST=3001, /* Request authorization to arm the vehicle to a external entity, the arm authorizer is responsible to request all data that is needs from the vehicle before authorize or deny the request. If approved the progress of command_ack message should be set with period of time that this authorization is valid in seconds or in case it was denied it should be set with one of the reasons in ARM_AUTH_DENIED_REASON.
         |Vehicle system id, this way ground station can request arm authorization on behalf of any vehicle| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
@@ -188,7 +188,7 @@ typedef enum MAV_CMD
         |Reserved| Reserved| Reserved| Reserved| Latitude| Longitude| Altitude|  */
   MAV_CMD_UAVCAN_GET_NODE_INFO=5200, /* Commands the vehicle to respond with a sequence of messages UAVCAN_NODE_INFO, one message per every UAVCAN node that is online. Note that some of the response messages can be lost, which the receiver can detect easily by checking whether every received UAVCAN_NODE_STATUS has a matching message UAVCAN_NODE_INFO received earlier; if not, this command should be sent again in order to request re-transmission of the node information messages. |Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)|  */
   MAV_CMD_PAYLOAD_PREPARE_DEPLOY=30001, /* Deploy payload on a Lat / Lon / Alt position. This includes the navigation to reach the required release position and velocity. |Operation mode. 0: prepare single payload deploy (overwriting previous requests), but do not execute it. 1: execute payload deploy immediately (rejecting further deploy commands during execution, but allowing abort). 2: add payload deploy to existing deployment list.| Desired approach vector in compass heading. A negative value indicates the system can define the approach vector at will.| Desired ground speed at release time. This can be overridden by the airframe in case it needs to meet minimum airspeed. A negative value indicates the system can define the ground speed at will.| Minimum altitude clearance to the release position. A negative value indicates the system can define the clearance at will.| Latitude unscaled for MISSION_ITEM or in 1e7 degrees for MISSION_ITEM_INT| Longitude unscaled for MISSION_ITEM or in 1e7 degrees for MISSION_ITEM_INT| Altitude (MSL), in meters|  */
-   MAV_CMD_PAYLOAD_CONTROL_DEPLOY=30002, /* Control the payload deployment. |Operation mode. 0: Abort deployment, continue normal mission. 1: switch to payload deployment mode. 100: delete first payload deployment request. 101: delete all payload deployment requests.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
+   MAV_CMD_PAYLOAD_CONTROL_DEPLOY=30002, /* Control the payload deployment. |payload deployment request. 101: delete all payload deployment requests.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
   MAV_CMD_WAYPOINT_USER_1=31000, /* User defined waypoint item. Ground Station will show the Vehicle as flying through this item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude (MSL), in meters|  */
   MAV_CMD_WAYPOINT_USER_2=31001, /* User defined waypoint item. Ground Station will show the Vehicle as flying through this item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude (MSL), in meters|  */
   MAV_CMD_WAYPOINT_USER_3=31002, /* User defined waypoint item. Ground Station will show the Vehicle as flying through this item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude (MSL), in meters|  */

--- a/matrixpilot/version.h
+++ b/matrixpilot/version.h
@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H

-#define MAVLINK_BUILD_DATE "Wed Aug 07 2019"
+#define MAVLINK_BUILD_DATE "Thu Aug 08 2019"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
 

--- a/message_definitions/common.xml
+++ b/message_definitions/common.xml
@@ -1553,11 +1553,11 @@
        <param index="2" label="RC Type" enum="RC_TYPE">RC type.</param>
      </entry>
      <entry value="510" name="MAV_CMD_GET_MESSAGE_INTERVAL" hasLocation="false" isDestination="false">
-        <description>Request the interval between messages for a particular MAVLink message ID</description>
+        <description>Request the interval between messages for a particular MAVLink message ID. The receiver should ACK the command and then emit its response in a MESSAGE_INTERVAL message.</description>
        <param index="1" label="Message ID" minValue="0" maxValue="16777215" increment="1">The MAVLink message ID</param>
      </entry>
      <entry value="511" name="MAV_CMD_SET_MESSAGE_INTERVAL" hasLocation="false" isDestination="false">
-        <description>Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM</description>
+        <description>Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM.</description>
        <param index="1" label="Message ID" minValue="0" maxValue="16777215" increment="1">The MAVLink message ID</param>
        <param index="2" label="Interval" units="us" minValue="-1" increment="1">The interval between two messages. Set to -1 to disable and 0 to request default rate.</param>
      </entry>
@@ -4736,7 +4736,7 @@
      <field type="uint64_t" name="time_usec" units="us">Timestamp (UNIX Epoch time or time since system boot). The receiving end can infer timestamp format (since 1.1.1970 or since system boot) by checking for the magnitude the number.</field>
    </message>
    <message id="244" name="MESSAGE_INTERVAL">
-      <description>The interval between messages for a particular MAVLink message ID. This interface replaces DATA_STREAM</description>
+      <description>The interval between messages for a particular MAVLink message ID. This message is the response to the MAV_CMD_GET_MESSAGE_INTERVAL command. This interface replaces DATA_STREAM.</description>
      <field type="uint16_t" name="message_id">The ID of the requested MAVLink message. v1.0 is limited to 254 messages.</field>
      <field type="int32_t" name="interval_us" units="us">The interval between two messages. A value of -1 indicates this stream is disabled, 0 indicates it is not available, &gt; 0 indicates the interval at which it is sent.</field>
    </message>

--- a/minimal/version.h
+++ b/minimal/version.h
@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H

-#define MAVLINK_BUILD_DATE "Wed Aug 07 2019"
+#define MAVLINK_BUILD_DATE "Thu Aug 08 2019"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 22
 

--- a/slugs/slugs.h
+++ b/slugs/slugs.h
@@ -117,8 +117,8 @@ typedef enum MAV_CMD
   MAV_CMD_COMPONENT_ARM_DISARM=400, /* Arms / Disarms a component |0: disarm, 1: arm| 0: only arm-disarm when landed, 21196: enforce arming/disarming even in-air (during flight)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_GET_HOME_POSITION=410, /* Request the home position from the vehicle. |Reserved| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
   MAV_CMD_START_RX_PAIR=500, /* Starts receiver pairing. |0:Spektrum.| RC type.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
-   MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
-   MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM |The MAVLink message ID| The interval between two messages. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID. The receiver should ACK the command and then emit its response in a MESSAGE_INTERVAL message. |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM. |The MAVLink message ID| s. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES=520, /* Request autopilot capabilities. The receiver should ACK the command and then emit its capabilities in an AUTOPILOT_VERSION message |1: Request autopilot version| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
@@ -134,10 +134,10 @@ typedef enum MAV_CMD
   MAV_CMD_SET_CAMERA_FOCUS=532, /* Set camera focus. Camera must respond with a CAMERA_SETTINGS message (on success). Use NaN for reserved values. |Focus type| Focus value| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_JUMP_TAG=600, /* Tagged jump target. Can be jumped to with MAV_CMD_DO_JUMP_TAG. |Tag.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_DO_JUMP_TAG=601, /* Jump to the matching tag in the mission list. Repeat this action for the specified number of times. A mission should contain a single matching tag for each jump. If this is not the case then a jump to a missing tag should complete the mission, and a jump where there are multiple matching tags should always select the one with the lowest mission sequence number. |Target tag to jump to.| Repeat count.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
-   MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| end on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_IMAGE_STOP_CAPTURE=2001, /* Stop image capture sequence Use NaN for reserved values. |Reserved (Set to 0)| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_REQUEST_CAMERA_IMAGE_CAPTURE=2002, /* Re-request a CAMERA_IMAGE_CAPTURE message. Use NaN for reserved values. |Sequence number for missing CAMERA_IMAGE_CAPTURE message| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
-   MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| e camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| 1 to pause triggering, but without switching the camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_VIDEO_START_CAPTURE=2500, /* Starts video capture (recording). Use NaN for reserved values. |Video Stream ID (0 for all streams)| Frequency CAMERA_CAPTURE_STATUS messages should be sent while recording (0 for no messages, otherwise frequency)| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_VIDEO_STOP_CAPTURE=2501, /* Stop the current video capture (recording). Use NaN for reserved values. |Video Stream ID (0 for all streams)| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_VIDEO_START_STREAMING=2502, /* Start video streaming |Video Stream ID (0 for all streams, 1 for first, 2 for second, etc.)| Reserved| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
@@ -148,7 +148,7 @@ typedef enum MAV_CMD
   MAV_CMD_LOGGING_STOP=2511, /* Request to stop streaming log data over MAVLink |Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)| Reserved (set to 0)|  */
   MAV_CMD_AIRFRAME_CONFIGURATION=2520, /*  |Landing gear ID (default: 0, -1 for all)| Landing gear position (Down: 0, Up: 1, NaN for no change)| Reserved, set to NaN| Reserved, set to NaN| Reserved, set to NaN| Reserved, set to NaN| Reserved, set to NaN|  */
   MAV_CMD_CONTROL_HIGH_LATENCY=2600, /* Request to start/stop transmitting over the high latency telemetry |Control transmission over high latency telemetry (0: stop, 1: start)| Empty| Empty| Empty| Empty| Empty| Empty|  */
-   MAV_CMD_PANORAMA_CREATE=2800, /* Create a panorama at the current position |Viewing angle horizontal of the panorama (+- 0.5 the total angle)| cal of panorama.| Speed of the horizontal rotation.| Speed of the vertical rotation.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_PANORAMA_CREATE=2800, /* Create a panorama at the current position |l angle)| Viewing angle vertical of panorama.| Speed of the horizontal rotation.| Speed of the vertical rotation.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_DO_VTOL_TRANSITION=3000, /* Request VTOL transition |The target VTOL state. Only MAV_VTOL_STATE_MC and MAV_VTOL_STATE_FW can be used.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_ARM_AUTHORIZATION_REQUEST=3001, /* Request authorization to arm the vehicle to a external entity, the arm authorizer is responsible to request all data that is needs from the vehicle before authorize or deny the request. If approved the progress of command_ack message should be set with period of time that this authorization is valid in seconds or in case it was denied it should be set with one of the reasons in ARM_AUTH_DENIED_REASON.
         |Vehicle system id, this way ground station can request arm authorization on behalf of any vehicle| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
@@ -177,7 +177,7 @@ typedef enum MAV_CMD
   MAV_CMD_GET_MID_LEVEL_COMMANDS=10014, /* Requests vehicle to send current mid-level commands to ground station. |Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_MIDLEVEL_STORAGE=10015, /* Requests storage of mid-level commands. |Mid-level command storage: 0: read from flash/EEPROM, 1: write to flash/EEPROM| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
   MAV_CMD_PAYLOAD_PREPARE_DEPLOY=30001, /* Deploy payload on a Lat / Lon / Alt position. This includes the navigation to reach the required release position and velocity. |Operation mode. 0: prepare single payload deploy (overwriting previous requests), but do not execute it. 1: execute payload deploy immediately (rejecting further deploy commands during execution, but allowing abort). 2: add payload deploy to existing deployment list.| Desired approach vector in compass heading. A negative value indicates the system can define the approach vector at will.| Desired ground speed at release time. This can be overridden by the airframe in case it needs to meet minimum airspeed. A negative value indicates the system can define the ground speed at will.| Minimum altitude clearance to the release position. A negative value indicates the system can define the clearance at will.| Latitude unscaled for MISSION_ITEM or in 1e7 degrees for MISSION_ITEM_INT| Longitude unscaled for MISSION_ITEM or in 1e7 degrees for MISSION_ITEM_INT| Altitude (MSL), in meters|  */
-   MAV_CMD_PAYLOAD_CONTROL_DEPLOY=30002, /* Control the payload deployment. |Operation mode. 0: Abort deployment, continue normal mission. 1: switch to payload deployment mode. 100: delete first payload deployment request. 101: delete all payload deployment requests.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
+   MAV_CMD_PAYLOAD_CONTROL_DEPLOY=30002, /* Control the payload deployment. |payload deployment request. 101: delete all payload deployment requests.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
   MAV_CMD_WAYPOINT_USER_1=31000, /* User defined waypoint item. Ground Station will show the Vehicle as flying through this item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude (MSL), in meters|  */
   MAV_CMD_WAYPOINT_USER_2=31001, /* User defined waypoint item. Ground Station will show the Vehicle as flying through this item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude (MSL), in meters|  */
   MAV_CMD_WAYPOINT_USER_3=31002, /* User defined waypoint item. Ground Station will show the Vehicle as flying through this item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude (MSL), in meters|  */

--- a/slugs/version.h
+++ b/slugs/version.h
@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H

-#define MAVLINK_BUILD_DATE "Wed Aug 07 2019"
+#define MAVLINK_BUILD_DATE "Thu Aug 08 2019"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
 

--- a/standard/version.h
+++ b/standard/version.h
@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H

-#define MAVLINK_BUILD_DATE "Wed Aug 07 2019"
+#define MAVLINK_BUILD_DATE "Thu Aug 08 2019"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
 

--- a/test/version.h
+++ b/test/version.h
@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H

-#define MAVLINK_BUILD_DATE "Wed Aug 07 2019"
+#define MAVLINK_BUILD_DATE "Thu Aug 08 2019"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 179
 

--- a/uAvionix/version.h
+++ b/uAvionix/version.h
@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H

-#define MAVLINK_BUILD_DATE "Wed Aug 07 2019"
+#define MAVLINK_BUILD_DATE "Thu Aug 08 2019"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255