[PATCH] Fix pcnet_cs network hotplug

pcnet_cs registers the network device too early.  The effect of this
is that the networking hotplug scripts are unable to bring the device
up automatically.

There are two issues:
- we were registering the net device before we finished setting up
  the device (eg, reading the MAC address.)
- we were using DEV_CONFIG_PENDING to block the net device "open"
  callback, and as we know the other methods may be called prior
  to open.

My only concern with this patch is that we set info->node.dev_name
after we register the net device, so use of cardctl during the
hotplug scripts may give unexpected results.  However, I am not
aware of anyone using cardctl to read the device name in network
hotplug scripts.

Please review and merge.  Thanks.

drivers/net/pcmcia/pcnet_cs.c

@@ -681,10 +681,6 @@ static void pcnet_config(dev_link_t *link)
     } else {
 	dev->if_port = 0;
     }
-    if (register_netdev(dev) != 0) {
-	printk(KERN_NOTICE "pcnet_cs: register_netdev() failed\n");
-	goto failed;
-    }
 
     hw_info = get_hwinfo(link);
     if (hw_info == NULL)
@@ -699,7 +695,6 @@ static void pcnet_config(dev_link_t *link)
     if (hw_info == NULL) {
 	printk(KERN_NOTICE "pcnet_cs: unable to read hardware net"
 	       " address for io base %#3lx\n", dev->base_addr);
-	unregister_netdev(dev);
 	goto failed;
     }
 
@@ -733,8 +728,6 @@ static void pcnet_config(dev_link_t *link)
     ei_status.word16 = 1;
     ei_status.reset_8390 = &pcnet_reset_8390;
 
-    strcpy(info->node.dev_name, dev->name);
-    link->dev = &info->node;
     SET_ETHTOOL_OPS(dev, &netdev_ethtool_ops);
 
     if (info->flags & (IS_DL10019|IS_DL10022)) {
@@ -743,6 +736,21 @@ static void pcnet_config(dev_link_t *link)
 	mii_phy_probe(dev);
 	if ((id == 0x30) && !info->pna_phy && (info->eth_phy == 4))
 	    info->eth_phy = 0;
+    }
+
+    link->dev = &info->node;
+    link->state &= ~DEV_CONFIG_PENDING;
+
+    if (register_netdev(dev) != 0) {
+	printk(KERN_NOTICE "pcnet_cs: register_netdev() failed\n");
+	link->dev = NULL;
+	goto failed;
+    }
+
+    strcpy(info->node.dev_name, dev->name);
+
+    if (info->flags & (IS_DL10019|IS_DL10022)) {
+	u_char id = inb(dev->base_addr + 0x1a);
 	printk(KERN_INFO "%s: NE2000 (DL100%d rev %02x): ",
 	       dev->name, ((info->flags & IS_DL10022) ? 22 : 19), id);
 	if (info->pna_phy)
@@ -758,7 +766,6 @@ static void pcnet_config(dev_link_t *link)
     printk(" hw_addr ");
     for (i = 0; i < 6; i++)
 	printk("%02X%s", dev->dev_addr[i], ((i<5) ? ":" : "\n"));
-    link->state &= ~DEV_CONFIG_PENDING;
     return;
 
 cs_failed: