Staging: Merge Ben Collins solo6x10 tree with upstream

There were some duplicate changes that needed to be hand-merged due to
fixes needed to keep .37 building and working properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drivers/staging/solo6x10/Kconfig

 config SOLO6X10
 	tristate "Softlogic 6x10 MPEG codec cards"
 	depends on PCI && VIDEO_DEV && SND
-	select VIDEOBUF_DMA_CONTIG
+	select VIDEOBUF_DMA_SG
 	---help---
 	  This driver supports the Softlogic based MPEG-4 and h.264 codec
 	  codec cards.

drivers/staging/solo6x10/TODO

 TODO (staging => main):
 
-	* checkpatch.pl (haven't run it yet)
-	* Lindent (should be clean, but check)
 	* Motion detection flags need to be moved to v4l2
 	* Some private CIDs need to be moved to v4l2
 
@@ -21,8 +19,6 @@ TODO (general):
 	  - implement playback via external sound jack
 	  - implement loopback of external sound jack with incoming audio?
 	  - implement pause/resume
-	  - check into jacking sound from tx28xx chips directly (to avoid
-	    g.723/8khz limitations)
 
 Plase send patches to Greg Kroah-Hartman <greg@kroah.com> and Cc Ben Collins
 <bcollins@bluecherry.net>

drivers/staging/solo6x10/solo6010-core.c

@@ -136,6 +136,7 @@ static int __devinit solo6010_pci_probe(struct pci_dev *pdev,
 	int ret;
 	int sdram;
 	u8 chip_id;
+
 	solo_dev = kzalloc(sizeof(*solo_dev), GFP_KERNEL);
 	if (solo_dev == NULL)
 		return -ENOMEM;
@@ -261,13 +262,18 @@ static void __devexit solo6010_pci_remove(struct pci_dev *pdev)
 }
 
 static struct pci_device_id solo6010_id_table[] = {
+	/* 6010 based cards */
 	{PCI_DEVICE(PCI_VENDOR_ID_SOFTLOGIC, PCI_DEVICE_ID_SOLO6010)},
 	{PCI_DEVICE(PCI_VENDOR_ID_BLUECHERRY, PCI_DEVICE_ID_NEUSOLO_4)},
 	{PCI_DEVICE(PCI_VENDOR_ID_BLUECHERRY, PCI_DEVICE_ID_NEUSOLO_9)},
 	{PCI_DEVICE(PCI_VENDOR_ID_BLUECHERRY, PCI_DEVICE_ID_NEUSOLO_16)},
-	{PCI_DEVICE(PCI_VENDOR_ID_BLUECHERRY, PCI_DEVICE_ID_COMMSOLO_4)},
-	{PCI_DEVICE(PCI_VENDOR_ID_BLUECHERRY, PCI_DEVICE_ID_COMMSOLO_9)},
-	{PCI_DEVICE(PCI_VENDOR_ID_BLUECHERRY, PCI_DEVICE_ID_COMMSOLO_16)},
+	{PCI_DEVICE(PCI_VENDOR_ID_BLUECHERRY, PCI_DEVICE_ID_BC_SOLO_4)},
+	{PCI_DEVICE(PCI_VENDOR_ID_BLUECHERRY, PCI_DEVICE_ID_BC_SOLO_9)},
+	{PCI_DEVICE(PCI_VENDOR_ID_BLUECHERRY, PCI_DEVICE_ID_BC_SOLO_16)},
+	/* 6110 based cards */
+	{PCI_DEVICE(PCI_VENDOR_ID_BLUECHERRY, PCI_DEVICE_ID_BC_6110_4)},
+	{PCI_DEVICE(PCI_VENDOR_ID_BLUECHERRY, PCI_DEVICE_ID_BC_6110_8)},
+	{PCI_DEVICE(PCI_VENDOR_ID_BLUECHERRY, PCI_DEVICE_ID_BC_6110_16)},
 	{0,}
 };
 

drivers/staging/solo6x10/solo6010-i2c.c

@@ -227,7 +227,7 @@ static int solo_i2c_master_xfer(struct i2c_adapter *adap,
 	if (i == SOLO_I2C_ADAPTERS)
 		return num; // XXX Right return value for failure?
 
-	down(&solo_dev->i2c_sem);
+	mutex_lock(&solo_dev->i2c_mutex);
 	solo_dev->i2c_id = i;
 	solo_dev->i2c_msg = msgs;
 	solo_dev->i2c_msg_num = num;
@@ -258,7 +258,7 @@ static int solo_i2c_master_xfer(struct i2c_adapter *adap,
 	solo_dev->i2c_state = IIC_STATE_IDLE;
 	solo_dev->i2c_id = -1;
 
-	up(&solo_dev->i2c_sem);
+	mutex_unlock(&solo_dev->i2c_mutex);
 
 	return ret;
 }
@@ -284,7 +284,7 @@ int solo_i2c_init(struct solo6010_dev *solo_dev)
 	solo_dev->i2c_id = -1;
 	solo_dev->i2c_state = IIC_STATE_IDLE;
 	init_waitqueue_head(&solo_dev->i2c_wait);
-	sema_init(&solo_dev->i2c_sem, 1);
+	mutex_init(&solo_dev->i2c_mutex);
 
 	for (i = 0; i < SOLO_I2C_ADAPTERS; i++) {
 		struct i2c_adapter *adap = &solo_dev->i2c_adap[i];

drivers/staging/solo6x10/solo6010-p2m.c

@@ -18,6 +18,7 @@
  */
 
 #include <linux/kernel.h>
+#include <linux/scatterlist.h>
 
 #include "solo6010.h"
 
@@ -30,8 +31,9 @@ int solo_p2m_dma(struct solo6010_dev *solo_dev, u8 id, int wr,
 	int ret;
 
 	WARN_ON(!size);
-	WARN_ON(id >= SOLO_NR_P2M);
-	if (!size || id >= SOLO_NR_P2M)
+	BUG_ON(id >= SOLO_NR_P2M);
+
+	if (!size)
 		return -EINVAL;
 
 	dma_addr = pci_map_single(solo_dev->pdev, sys_addr, size,
@@ -47,42 +49,137 @@ int solo_p2m_dma(struct solo6010_dev *solo_dev, u8 id, int wr,
 
 int solo_p2m_dma_t(struct solo6010_dev *solo_dev, u8 id, int wr,
 		   dma_addr_t dma_addr, u32 ext_addr, u32 size)
+{
+	struct p2m_desc *desc = kzalloc(sizeof(*desc) * 2, GFP_DMA);
+	int ret;
+
+	if (desc == NULL)
+		return -ENOMEM;
+
+	solo_p2m_push_desc(&desc[1], wr, dma_addr, ext_addr, size, 0, 0);
+	ret = solo_p2m_dma_desc(solo_dev, id, desc, 2);
+	kfree(desc);
+
+	return ret;
+}
+
+void solo_p2m_push_desc(struct p2m_desc *desc, int wr, dma_addr_t dma_addr,
+			u32 ext_addr, u32 size, int repeat, u32 ext_size)
+{
+	desc->ta = dma_addr;
+	desc->fa = ext_addr;
+
+	desc->ext = SOLO_P2M_COPY_SIZE(size >> 2);
+	desc->ctrl = SOLO_P2M_BURST_SIZE(SOLO_P2M_BURST_256) |
+		(wr ? SOLO_P2M_WRITE : 0) | SOLO_P2M_TRANS_ON;
+
+	/* Ext size only matters when we're repeating */
+	if (repeat) {
+		desc->ext |= SOLO_P2M_EXT_INC(ext_size >> 2);
+		desc->ctrl |=  SOLO_P2M_PCI_INC(size >> 2) |
+			SOLO_P2M_REPEAT(repeat);
+	}
+}
+
+int solo_p2m_dma_desc(struct solo6010_dev *solo_dev, u8 id,
+		      struct p2m_desc *desc, int desc_count)
 {
 	struct solo_p2m_dev *p2m_dev;
-	unsigned int timeout = 0;
+	unsigned int timeout;
+	int ret = 0;
+	u32 config = 0;
+	dma_addr_t desc_dma = 0;
 
-	WARN_ON(!size);
-	WARN_ON(id >= SOLO_NR_P2M);
-	if (!size || id >= SOLO_NR_P2M)
-		return -EINVAL;
+	BUG_ON(id >= SOLO_NR_P2M);
+	BUG_ON(!desc_count || desc_count > SOLO_NR_P2M_DESC);
 
 	p2m_dev = &solo_dev->p2m_dev[id];
 
-	down(&p2m_dev->sem);
+	mutex_lock(&p2m_dev->mutex);
+
+	solo_reg_write(solo_dev, SOLO_P2M_CONTROL(id), 0);
 
-start_dma:
 	INIT_COMPLETION(p2m_dev->completion);
 	p2m_dev->error = 0;
-	solo_reg_write(solo_dev, SOLO_P2M_TAR_ADR(id), dma_addr);
-	solo_reg_write(solo_dev, SOLO_P2M_EXT_ADR(id), ext_addr);
-	solo_reg_write(solo_dev, SOLO_P2M_EXT_CFG(id),
-		       SOLO_P2M_COPY_SIZE(size >> 2));
-	solo_reg_write(solo_dev, SOLO_P2M_CONTROL(id),
-		       SOLO_P2M_BURST_SIZE(SOLO_P2M_BURST_256) |
-		       (wr ? SOLO_P2M_WRITE : 0) | SOLO_P2M_TRANS_ON);
 
+	/* Enable the descriptors */
+	config = solo_reg_read(solo_dev, SOLO_P2M_CONFIG(id));
+	desc_dma = pci_map_single(solo_dev->pdev, desc,
+				  desc_count * sizeof(*desc),
+				  PCI_DMA_TODEVICE);
+	solo_reg_write(solo_dev, SOLO_P2M_DES_ADR(id), desc_dma);
+	solo_reg_write(solo_dev, SOLO_P2M_DESC_ID(id), desc_count - 1);
+	solo_reg_write(solo_dev, SOLO_P2M_CONFIG(id), config |
+		       SOLO_P2M_DESC_MODE);
+
+	/* Should have all descriptors completed from one interrupt */
 	timeout = wait_for_completion_timeout(&p2m_dev->completion, HZ);
 
 	solo_reg_write(solo_dev, SOLO_P2M_CONTROL(id), 0);
 
-	/* XXX Really looks to me like we will get stuck here if a
-	 * real PCI P2M error occurs */
+	/* Reset back to non-descriptor mode */
+	solo_reg_write(solo_dev, SOLO_P2M_CONFIG(id), config);
+	solo_reg_write(solo_dev, SOLO_P2M_DESC_ID(id), 0);
+	solo_reg_write(solo_dev, SOLO_P2M_DES_ADR(id), 0);
+	pci_unmap_single(solo_dev->pdev, desc_dma,
+			 desc_count * sizeof(*desc),
+			 PCI_DMA_TODEVICE);
+
 	if (p2m_dev->error)
-		goto start_dma;
+		ret = -EIO;
+	else if (timeout == 0)
+		ret = -EAGAIN;
+
+	mutex_unlock(&p2m_dev->mutex);
+
+	WARN_ON_ONCE(ret);
+
+	return ret;
+}
+
+int solo_p2m_dma_sg(struct solo6010_dev *solo_dev, u8 id,
+		    struct p2m_desc *pdesc, int wr,
+		    struct scatterlist *sg, u32 sg_off,
+		    u32 ext_addr, u32 size)
+{
+	int i;
+	int idx;
+
+	BUG_ON(id >= SOLO_NR_P2M);
 
-	up(&p2m_dev->sem);
+	if (WARN_ON_ONCE(!size))
+		return -EINVAL;
+
+	memset(pdesc, 0, sizeof(*pdesc));
+
+	/* Should rewrite this to handle > SOLO_NR_P2M_DESC transactions */
+	for (i = 0, idx = 1; idx < SOLO_NR_P2M_DESC && sg && size > 0;
+	     i++, sg = sg_next(sg)) {
+		struct p2m_desc *desc = &pdesc[idx];
+		u32 sg_len = sg_dma_len(sg);
+		u32 len;
+
+		if (sg_off >= sg_len) {
+			sg_off -= sg_len;
+			continue;
+		}
 
-	return (timeout == 0) ? -EAGAIN : 0;
+		sg_len -= sg_off;
+		len = min(sg_len, size);
+
+		solo_p2m_push_desc(desc, wr, sg_dma_address(sg) + sg_off,
+				   ext_addr, len, 0, 0);
+
+		size -= len;
+		ext_addr += len;
+		idx++;
+
+		sg_off = 0;
+	}
+
+	WARN_ON_ONCE(size || i >= SOLO_NR_P2M_DESC);
+
+	return solo_p2m_dma_desc(solo_dev, id, pdesc, idx);
 }
 
 #ifdef SOLO_TEST_P2M
@@ -152,8 +249,11 @@ static void run_p2m_test(struct solo6010_dev *solo_dev)
 
 void solo_p2m_isr(struct solo6010_dev *solo_dev, int id)
 {
+	struct solo_p2m_dev *p2m_dev = &solo_dev->p2m_dev[id];
+
 	solo_reg_write(solo_dev, SOLO_IRQ_STAT, SOLO_IRQ_P2M(id));
-	complete(&solo_dev->p2m_dev[id].completion);
+
+	complete(&p2m_dev->completion);
 }
 
 void solo_p2m_error_isr(struct solo6010_dev *solo_dev, u32 status)
@@ -188,16 +288,14 @@ int solo_p2m_init(struct solo6010_dev *solo_dev)
 	for (i = 0; i < SOLO_NR_P2M; i++) {
 		p2m_dev = &solo_dev->p2m_dev[i];
 
-		sema_init(&p2m_dev->sem, 1);
+		mutex_init(&p2m_dev->mutex);
 		init_completion(&p2m_dev->completion);
 
-		solo_reg_write(solo_dev, SOLO_P2M_DES_ADR(i),
-			       __pa(p2m_dev->desc));
-
 		solo_reg_write(solo_dev, SOLO_P2M_CONTROL(i), 0);
 		solo_reg_write(solo_dev, SOLO_P2M_CONFIG(i),
 			       SOLO_P2M_CSC_16BIT_565 |
-			       SOLO_P2M_DMA_INTERVAL(0) |
+			       SOLO_P2M_DMA_INTERVAL(3) |
+			       SOLO_P2M_DESC_INTR_OPT |
 			       SOLO_P2M_PCI_MASTER_MODE);
 		solo6010_irq_on(solo_dev, SOLO_IRQ_P2M(i));
 	}

drivers/staging/solo6x10/solo6010-v4l2.c

@@ -24,14 +24,13 @@
 
 #include <media/v4l2-ioctl.h>
 #include <media/v4l2-common.h>
-#include <media/videobuf-dma-contig.h>
+#include <media/videobuf-dma-sg.h>
 
 #include "solo6010.h"
 #include "solo6010-tw28.h"
 
 #define SOLO_HW_BPL		2048
 #define SOLO_DISP_PIX_FIELD	V4L2_FIELD_INTERLACED
-#define SOLO_DISP_BUF_SIZE	(64 * 1024) // 64k
 
 /* Image size is two fields, SOLO_HW_BPL is one horizontal line */
 #define solo_vlines(__solo)	(__solo->video_vsize * 2)
@@ -49,6 +48,8 @@ struct solo_filehandle {
 	spinlock_t		slock;
 	int			old_write;
 	struct list_head	vidq_active;
+	struct p2m_desc		desc[SOLO_NR_P2M_DESC];
+	int			desc_idx;
 };
 
 unsigned video_nr = -1;
@@ -203,50 +204,148 @@ static int solo_v4l2_set_ch(struct solo6010_dev *solo_dev, u8 ch)
 	return 0;
 }
 
+static void disp_reset_desc(struct solo_filehandle *fh)
+{
+	/* We use desc mode, which ignores desc 0 */
+	memset(fh->desc, 0, sizeof(*fh->desc));
+	fh->desc_idx = 1;
+}
+
+static int disp_flush_descs(struct solo_filehandle *fh)
+{
+	int ret;
+
+	if (!fh->desc_idx)
+		return 0;
+
+	ret = solo_p2m_dma_desc(fh->solo_dev, SOLO_P2M_DMA_ID_DISP,
+				fh->desc, fh->desc_idx);
+	disp_reset_desc(fh);
+
+	return ret;
+}
+
+static int disp_push_desc(struct solo_filehandle *fh, dma_addr_t dma_addr,
+		      u32 ext_addr, int size, int repeat, int ext_size)
+{
+	if (fh->desc_idx >= SOLO_NR_P2M_DESC) {
+		int ret = disp_flush_descs(fh);
+		if (ret)
+			return ret;
+	}
+
+	solo_p2m_push_desc(&fh->desc[fh->desc_idx], 0, dma_addr, ext_addr,
+			   size, repeat, ext_size);
+	fh->desc_idx++;
+
+	return 0;
+}
+
 static void solo_fillbuf(struct solo_filehandle *fh,
 			 struct videobuf_buffer *vb)
 {
 	struct solo6010_dev *solo_dev = fh->solo_dev;
-	dma_addr_t vbuf;
+	struct videobuf_dmabuf* vbuf;
 	unsigned int fdma_addr;
-	int frame_size;
 	int error = 1;
 	int i;
+	struct scatterlist* sg;
+	dma_addr_t sg_dma;
+	int sg_size_left;
 
-	if (!(vbuf = videobuf_to_dma_contig(vb)))
+	if (!(vbuf = videobuf_to_dma(vb)))
 		goto finish_buf;
 
 	if (erase_off(solo_dev)) {
-		void *p = videobuf_queue_to_vaddr(&fh->vidq, vb);
-		int image_size = solo_image_size(solo_dev);
-		for (i = 0; i < image_size; i += 2) {
+		int i;
+
+		/* Just blit to the entire sg list, ignoring size */
+		for_each_sg(vbuf->sglist, sg, vbuf->sglen, i) {
+			void *p = sg_virt(sg);
+			size_t len = sg_dma_len(sg);
+
+			for (i = 0; i < len; i += 2) {
 				((u8 *)p)[i] = 0x80;
 				((u8 *)p)[i + 1] = 0x00;
 			}
+		}
+
 		error = 0;
 		goto finish_buf;
 	}
 
-	frame_size = SOLO_HW_BPL * solo_vlines(solo_dev);
-	fdma_addr = SOLO_DISP_EXT_ADDR(solo_dev) + (fh->old_write * frame_size);
+	disp_reset_desc(fh);
+	sg = vbuf->sglist;
+	sg_dma = sg_dma_address(sg);
+	sg_size_left = sg_dma_len(sg);
+
+	fdma_addr = SOLO_DISP_EXT_ADDR(solo_dev) + (fh->old_write *
+			(SOLO_HW_BPL * solo_vlines(solo_dev)));
 
-	for (i = 0; i < frame_size / SOLO_DISP_BUF_SIZE; i++) {
-		int j;
-		for (j = 0; j < (SOLO_DISP_BUF_SIZE / SOLO_HW_BPL); j++) {
-			if (solo_p2m_dma_t(solo_dev, SOLO_P2M_DMA_ID_DISP, 0,
-					   vbuf, fdma_addr + (j * SOLO_HW_BPL),
-					   solo_bytesperline(solo_dev)))
+	for (i = 0; i < solo_vlines(solo_dev); i++) {
+		int line_len = solo_bytesperline(solo_dev);
+		int lines;
+
+		if (!sg_size_left) {
+			sg = sg_next(sg);
+			if (sg == NULL)
 				goto finish_buf;
-			vbuf += solo_bytesperline(solo_dev);
+			sg_dma = sg_dma_address(sg);
+			sg_size_left = sg_dma_len(sg);
 		}
-		fdma_addr += SOLO_DISP_BUF_SIZE;
+
+		/* No room for an entire line, so chunk it up */
+		if (sg_size_left < line_len) {
+			int this_addr = fdma_addr;
+
+			while (line_len > 0) {
+				int this_write;
+
+				if (!sg_size_left) {
+					sg = sg_next(sg);
+					if (sg == NULL)
+						goto finish_buf;
+					sg_dma = sg_dma_address(sg);
+					sg_size_left = sg_dma_len(sg);
 				}
-	error = 0;
+
+				this_write = min(sg_size_left, line_len);
+
+				if (disp_push_desc(fh, sg_dma, this_addr,
+						   this_write, 0, 0))
+					goto finish_buf;
+
+				line_len -= this_write;
+				sg_size_left -= this_write;
+				sg_dma += this_write;
+				this_addr += this_write;
+			}
+
+			fdma_addr += SOLO_HW_BPL;
+			continue;
+		}
+
+		/* Shove as many lines into a repeating descriptor as possible */
+		lines = min(sg_size_left / line_len,
+			    solo_vlines(solo_dev) - i);
+
+		if (disp_push_desc(fh, sg_dma, fdma_addr, line_len,
+				   lines - 1, SOLO_HW_BPL))
+			goto finish_buf;
+
+		i += lines - 1;
+		fdma_addr += SOLO_HW_BPL * lines;
+		sg_dma += lines * line_len;
+		sg_size_left -= lines * line_len;
+	}
+
+	error = disp_flush_descs(fh);
 
 finish_buf:
 	if (error) {
 		vb->state = VIDEOBUF_ERROR;
 	} else {
+		vb->size = solo_vlines(solo_dev) * solo_bytesperline(solo_dev);
 		vb->state = VIDEOBUF_DONE;
 		vb->field_count++;
 		do_gettimeofday(&vb->ts);
@@ -364,7 +463,9 @@ static int solo_buf_prepare(struct videobuf_queue *vq,
 	if (vb->state == VIDEOBUF_NEEDS_INIT) {
 		int rc = videobuf_iolock(vq, vb, NULL);
 		if (rc < 0) {
-			videobuf_dma_contig_free(vq, vb);
+			struct videobuf_dmabuf *dma = videobuf_to_dma(vb);
+			videobuf_dma_unmap(vq->dev, dma);
+			videobuf_dma_free(dma);
 			vb->state = VIDEOBUF_NEEDS_INIT;
 			return rc;
 		}
@@ -388,7 +489,10 @@ static void solo_buf_queue(struct videobuf_queue *vq,
 static void solo_buf_release(struct videobuf_queue *vq,
 			     struct videobuf_buffer *vb)
 {
-	videobuf_dma_contig_free(vq, vb);
+	struct videobuf_dmabuf *dma = videobuf_to_dma(vb);
+
+	videobuf_dma_unmap(vq->dev, dma);
+	videobuf_dma_free(dma);
 	vb->state = VIDEOBUF_NEEDS_INIT;
 }
 
@@ -433,7 +537,7 @@ static int solo_v4l2_open(struct file *file)
 		return ret;
 	}
 
-	videobuf_queue_dma_contig_init(&fh->vidq, &solo_video_qops,
+	videobuf_queue_sg_init(&fh->vidq, &solo_video_qops,
 			       &solo_dev->pdev->dev, &fh->slock,
 			       V4L2_BUF_TYPE_VIDEO_CAPTURE,
 			       SOLO_DISP_PIX_FIELD,
@@ -530,7 +634,7 @@ static int solo_enum_input(struct file *file, void *priv,
 	if (solo_dev->video_type == SOLO_VO_FMT_TYPE_NTSC)
 		input->std = V4L2_STD_NTSC_M;
 	else
-		input->std = V4L2_STD_PAL_M;
+		input->std = V4L2_STD_PAL_B;
 
 	return 0;
 }
@@ -795,7 +899,7 @@ static struct video_device solo_v4l2_template = {
 	.minor			= -1,
 	.release		= video_device_release,
 
-	.tvnorms		= V4L2_STD_NTSC_M | V4L2_STD_PAL_M,
+	.tvnorms		= V4L2_STD_NTSC_M | V4L2_STD_PAL_B,
 	.current_norm		= V4L2_STD_NTSC_M,
 };
 

drivers/staging/solo6x10/solo6010.h

@@ -26,8 +26,8 @@
 #include <linux/semaphore.h>
 #include <linux/mutex.h>
 #include <linux/list.h>
-#include <linux/delay.h>
 #include <linux/wait.h>
+#include <linux/delay.h>
 #include <asm/io.h>
 #include <asm/atomic.h>
 
@@ -48,10 +48,14 @@
 #define PCI_DEVICE_ID_NEUSOLO_4		0x4304
 #define PCI_DEVICE_ID_NEUSOLO_9		0x4309
 #define PCI_DEVICE_ID_NEUSOLO_16	0x4310
-/* Commell Softlogic 6010 based cards */
-#define PCI_DEVICE_ID_COMMSOLO_4	0x4E04
-#define PCI_DEVICE_ID_COMMSOLO_9	0x4E09
-#define PCI_DEVICE_ID_COMMSOLO_16	0x4E10
+/* Bluecherry Softlogic 6010 based cards */
+#define PCI_DEVICE_ID_BC_SOLO_4		0x4E04
+#define PCI_DEVICE_ID_BC_SOLO_9		0x4E09
+#define PCI_DEVICE_ID_BC_SOLO_16	0x4E10
+/* Bluecherry Softlogic 6110 based cards */
+#define PCI_DEVICE_ID_BC_6110_4		0x5304
+#define PCI_DEVICE_ID_BC_6110_8		0x5308
+#define PCI_DEVICE_ID_BC_6110_16	0x5310
 #endif /* Bluecherry */
 
 #define SOLO6010_NAME			"solo6010"
@@ -78,7 +82,6 @@
 /* DMA Engine setup */
 #define SOLO_NR_P2M			4
 #define SOLO_NR_P2M_DESC		256
-#define SOLO_P2M_DESC_SIZE		(SOLO_NR_P2M_DESC * 16)
 /* MPEG and JPEG share the same interrupt and locks so they must be together
  * in the same dma channel. */
 #define SOLO_P2M_DMA_ID_MP4E		0
@@ -123,11 +126,17 @@ enum SOLO_I2C_STATE {
 	IIC_STATE_STOP
 };
 
+struct p2m_desc {
+	u32 ctrl;
+	u32 ext;
+	u32 ta;
+	u32 fa;
+};
+
 struct solo_p2m_dev {
-	struct semaphore	sem;
+	struct mutex		mutex;
 	struct completion	completion;
 	int			error;
-	u8			desc[SOLO_P2M_DESC_SIZE];
 };
 
 #define OSD_TEXT_MAX		30
@@ -185,7 +194,7 @@ struct solo6010_dev {
 	/* i2c related items */
 	struct i2c_adapter	i2c_adap[SOLO_I2C_ADAPTERS];
 	enum SOLO_I2C_STATE	i2c_state;
-	struct semaphore	i2c_sem;
+	struct mutex		i2c_mutex;
 	int			i2c_id;
 	wait_queue_head_t	i2c_wait;
 	struct i2c_msg		*i2c_msg;
@@ -306,6 +315,14 @@ int solo_p2m_dma_t(struct solo6010_dev *solo_dev, u8 id, int wr,
 		   dma_addr_t dma_addr, u32 ext_addr, u32 size);
 int solo_p2m_dma(struct solo6010_dev *solo_dev, u8 id, int wr,
 		 void *sys_addr, u32 ext_addr, u32 size);
+int solo_p2m_dma_sg(struct solo6010_dev *solo_dev, u8 id,
+		    struct p2m_desc *pdesc, int wr,
+		    struct scatterlist *sglist, u32 sg_off,
+		    u32 ext_addr, u32 size);
+void solo_p2m_push_desc(struct p2m_desc *desc, int wr, dma_addr_t dma_addr,
+			u32 ext_addr, u32 size, int repeat, u32 ext_size);
+int solo_p2m_dma_desc(struct solo6010_dev *solo_dev, u8 id,
+		      struct p2m_desc *desc, int desc_count);
 
 /* Set the threshold for motion detection */
 void solo_set_motion_threshold(struct solo6010_dev *solo_dev, u8 ch, u16 val);