Merge branch 'next' into for-linus

Prepare first round of input updates for 4.8 merge window.

Documentation/devicetree/bindings/input/atmel,captouch.txt

+Device tree bindings for Atmel capacitive touch device, typically
+an Atmel touch sensor connected to AtmegaXX MCU running firmware
+based on Qtouch library.
+
+The node for this device must be a child of a I2C controller node, as the
+device communicates via I2C.
+
+Required properties:
+
+	compatible:	Must be "atmel,captouch".
+	reg:		The I2C slave address of the device.
+	interrupts:	Property describing the interrupt line the device
+			is connected to. The device only has one interrupt
+			source.
+	linux,keycodes:	Specifies an array of numeric keycode values to
+			be used for reporting button presses. The array can
+			contain up to 8 entries.
+
+Optional properties:
+
+	autorepeat:	Enables the Linux input system's autorepeat
+			feature on the input device.
+
+Example:
+
+	atmel-captouch@51 {
+		compatible = "atmel,captouch";
+		reg = <0x51>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <67 IRQ_TYPE_EDGE_FALLING>;
+		linux,keycodes = <BTN_0>, <BTN_1>,
+			<BTN_2>, <BTN_3>,
+			<BTN_4>, <BTN_5>,
+			<BTN_6>, <BTN_7>;
+		autorepeat;
+	};

Documentation/devicetree/bindings/input/raydium_i2c_ts.txt

+Raydium I2C touchscreen
+
+Required properties:
+- compatible: must be "raydium,rm32380"
+- reg: The I2C address of the device
+- interrupt-parent: the phandle for the interrupt controller
+- interrupts: interrupt to which the chip is connected
+    See ../interrupt-controller/interrupts.txt
+Optional properties:
+- avdd-supply: analog power supply needed to power device
+- vccio-supply: IO Power source
+- reset-gpios: reset gpio the chip is connected to.
+
+Example:
+	touchscreen@39 {
+		compatible = "raydium,rm32380";
+		reg = <0x39>;
+		interrupt-parent = <&gpio>;
+		interrupts = <0x0 IRQ_TYPE_EDGE_FALLING>;
+	};

Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt

@@ -22,6 +22,15 @@ See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
 - syna,reset-delay-ms: The number of milliseconds to wait after resetting the
 			device.
 
+- syna,startup-delay-ms: The number of milliseconds to wait after powering on
+			 the device.
+
+- vdd-supply: VDD power supply.
+See ../regulator/regulator.txt
+
+- vio-supply: VIO power supply
+See ../regulator/regulator.txt
+
 Function Parameters:
 Parameters specific to RMI functions are contained in child nodes of the rmi device
  node. Documentation for the parameters of each function can be found in:

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -198,6 +198,7 @@ raidsonic	RaidSonic Technology GmbH
 ralink	Mediatek/Ralink Technology Corp.
 ramtron	Ramtron International
 raspberrypi	Raspberry Pi Foundation
+raydium	Raydium Semiconductor Corp.
 realtek Realtek Semiconductor Corp.
 renesas	Renesas Electronics Corporation
 richtek	Richtek Technology Corporation

drivers/input/input-mt.c

@@ -218,8 +218,23 @@ void input_mt_report_pointer_emulation(struct input_dev *dev, bool use_count)
 	}
 
 	input_event(dev, EV_KEY, BTN_TOUCH, count > 0);
-	if (use_count)
+
+	if (use_count) {
+		if (count == 0 &&
+		    !test_bit(ABS_MT_DISTANCE, dev->absbit) &&
+		    test_bit(ABS_DISTANCE, dev->absbit) &&
+		    input_abs_get_val(dev, ABS_DISTANCE) != 0) {
+			/*
+			 * Force reporting BTN_TOOL_FINGER for devices that
+			 * only report general hover (and not per-contact
+			 * distance) when contact is in proximity but not
+			 * on the surface.
+			 */
+			count = 1;
+		}
+
 		input_mt_report_finger_count(dev, count);
+	}
 
 	if (oldest) {
 		int x = input_mt_get_value(oldest, ABS_MT_POSITION_X);

drivers/input/input.c

@@ -153,8 +153,6 @@ static void input_pass_values(struct input_dev *dev,
 
 	rcu_read_unlock();
 
-	add_input_randomness(vals->type, vals->code, vals->value);
-
 	/* trigger auto repeat for key events */
 	if (test_bit(EV_REP, dev->evbit) && test_bit(EV_KEY, dev->evbit)) {
 		for (v = vals; v != vals + count; v++) {
@@ -371,9 +369,10 @@ static int input_get_disposition(struct input_dev *dev,
 static void input_handle_event(struct input_dev *dev,
 			       unsigned int type, unsigned int code, int value)
 {
-	int disposition;
+	int disposition = input_get_disposition(dev, type, code, &value);
 
-	disposition = input_get_disposition(dev, type, code, &value);
+	if (disposition != INPUT_IGNORE_EVENT && type != EV_SYN)
+		add_input_randomness(type, code, value);
 
 	if ((disposition & INPUT_PASS_TO_DEVICE) && dev->event)
 		dev->event(dev, type, code, value);

drivers/input/keyboard/tc3589x-keypad.c

@@ -32,7 +32,7 @@
 #define TC3589x_PULL_DOWN_MASK		0x1
 #define TC3589x_PULL_UP_MASK		0x2
 #define TC3589x_PULLUP_ALL_MASK		0xAA
-#define TC3589x_IO_PULL_VAL(index, mask)	((mask)<<((index)%4)*2))
+#define TC3589x_IO_PULL_VAL(index, mask)	((mask)<<((index)%4)*2)
 
 /* Bit masks for IOCFG register */
 #define IOCFG_BALLCFG		0x01

drivers/input/keyboard/tegra-kbc.c

@@ -552,7 +552,7 @@ static int tegra_kbc_parse_dt(struct tegra_kbc *kbc)
 
 	if (!num_rows || !num_cols || ((num_rows + num_cols) > KBC_MAX_GPIO)) {
 		dev_err(kbc->dev,
-			"keypad rows/columns not porperly specified\n");
+			"keypad rows/columns not properly specified\n");
 		return -EINVAL;
 	}
 

drivers/input/misc/Kconfig

@@ -82,6 +82,20 @@ config INPUT_ARIZONA_HAPTICS
 	  To compile this driver as a module, choose M here: the
 	  module will be called arizona-haptics.
 
+config INPUT_ATMEL_CAPTOUCH
+	tristate "Atmel Capacitive Touch Button Driver"
+	depends on OF || COMPILE_TEST
+	depends on I2C
+	help
+	  Say Y here if an Atmel Capacitive Touch Button device which
+	  implements "captouch" protocol is connected to I2C bus. Typically
+	  this device consists of Atmel Touch sensor controlled by AtMegaXX
+	  MCU running firmware based on Qtouch library.
+	  One should find "atmel,captouch" node in the board specific DTS.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called atmel_captouch.
+
 config INPUT_BMA150
 	tristate "BMA150/SMB380 acceleration sensor support"
 	depends on I2C
@@ -796,4 +810,13 @@ config INPUT_DRV2667_HAPTICS
 	  To compile this driver as a module, choose M here: the
 	  module will be called drv2667-haptics.
 
+config INPUT_HISI_POWERKEY
+	tristate "Hisilicon PMIC ONKEY support"
+	depends on ARCH_HISI || COMPILE_TEST
+	help
+	  Say Y to enable support for PMIC ONKEY.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called hisi_powerkey.
+
 endif

drivers/input/misc/Makefile

@@ -17,6 +17,7 @@ obj-$(CONFIG_INPUT_APANEL)		+= apanel.o
 obj-$(CONFIG_INPUT_ARIZONA_HAPTICS)	+= arizona-haptics.o
 obj-$(CONFIG_INPUT_ATI_REMOTE2)		+= ati_remote2.o
 obj-$(CONFIG_INPUT_ATLAS_BTNS)		+= atlas_btns.o
+obj-$(CONFIG_INPUT_ATMEL_CAPTOUCH)	+= atmel_captouch.o
 obj-$(CONFIG_INPUT_BFIN_ROTARY)		+= bfin_rotary.o
 obj-$(CONFIG_INPUT_BMA150)		+= bma150.o
 obj-$(CONFIG_INPUT_CM109)		+= cm109.o
@@ -34,6 +35,7 @@ obj-$(CONFIG_INPUT_DRV2667_HAPTICS)	+= drv2667.o
 obj-$(CONFIG_INPUT_GP2A)		+= gp2ap002a00f.o
 obj-$(CONFIG_INPUT_GPIO_BEEPER)		+= gpio-beeper.o
 obj-$(CONFIG_INPUT_GPIO_TILT_POLLED)	+= gpio_tilt_polled.o
+obj-$(CONFIG_INPUT_HISI_POWERKEY)	+= hisi_powerkey.o
 obj-$(CONFIG_HP_SDC_RTC)		+= hp_sdc_rtc.o
 obj-$(CONFIG_INPUT_IMS_PCU)		+= ims-pcu.o
 obj-$(CONFIG_INPUT_IXP4XX_BEEPER)	+= ixp4xx-beeper.o

drivers/input/misc/apanel.c

@@ -297,7 +297,7 @@ static int __init apanel_init(void)
 
 		if (slave != i2c_addr) {
 			pr_notice(APANEL ": only one SMBus slave "
-				  "address supported, skiping device...\n");
+				  "address supported, skipping device...\n");
 			continue;
 		}
 

drivers/input/misc/atmel_captouch.c

+/*
+ * Atmel Atmegaxx Capacitive Touch Button Driver
+ *
+ * Copyright (C) 2016 Google, inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+/*
+ * It's irrelevant that the HW used to develop captouch driver is based
+ * on Atmega88PA part and uses QtouchADC parts for sensing touch.
+ * Calling this driver "captouch" is an arbitrary way to distinguish
+ * the protocol this driver supported by other atmel/qtouch drivers.
+ *
+ * Captouch driver supports a newer/different version of the I2C
+ * registers/commands than the qt1070.c driver.
+ * Don't let the similarity of the general driver structure fool you.
+ *
+ * For raw i2c access from userspace, use i2cset/i2cget
+ * to poke at /dev/i2c-N devices.
+ */
+
+#include <linux/device.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/i2c.h>
+#include <linux/input.h>
+#include <linux/interrupt.h>
+#include <linux/slab.h>
+
+/* Maximum number of buttons supported */
+#define MAX_NUM_OF_BUTTONS		8
+
+/* Registers */
+#define REG_KEY1_THRESHOLD		0x02
+#define REG_KEY2_THRESHOLD		0x03
+#define REG_KEY3_THRESHOLD		0x04
+#define REG_KEY4_THRESHOLD		0x05
+
+#define REG_KEY1_REF_H			0x20
+#define REG_KEY1_REF_L			0x21
+#define REG_KEY2_REF_H			0x22
+#define REG_KEY2_REF_L			0x23
+#define REG_KEY3_REF_H			0x24
+#define REG_KEY3_REF_L			0x25
+#define REG_KEY4_REF_H			0x26
+#define REG_KEY4_REF_L			0x27
+
+#define REG_KEY1_DLT_H			0x30
+#define REG_KEY1_DLT_L			0x31
+#define REG_KEY2_DLT_H			0x32
+#define REG_KEY2_DLT_L			0x33
+#define REG_KEY3_DLT_H			0x34
+#define REG_KEY3_DLT_L			0x35
+#define REG_KEY4_DLT_H			0x36
+#define REG_KEY4_DLT_L			0x37
+
+#define REG_KEY_STATE			0x3C
+
+/*
+ * @i2c_client: I2C slave device client pointer
+ * @input: Input device pointer
+ * @num_btn: Number of buttons
+ * @keycodes: map of button# to KeyCode
+ * @prev_btn: Previous key state to detect button "press" or "release"
+ * @xfer_buf: I2C transfer buffer
+ */
+struct atmel_captouch_device {
+	struct i2c_client *client;
+	struct input_dev *input;
+	u32 num_btn;
+	u32 keycodes[MAX_NUM_OF_BUTTONS];
+	u8 prev_btn;
+	u8 xfer_buf[8] ____cacheline_aligned;
+};
+
+/*
+ * Read from I2C slave device
+ * The protocol is that the client has to provide both the register address
+ * and the length, and while reading back the device would prepend the data
+ * with address and length for verification.
+ */
+static int atmel_read(struct atmel_captouch_device *capdev,
+			 u8 reg, u8 *data, size_t len)
+{
+	struct i2c_client *client = capdev->client;
+	struct device *dev = &client->dev;
+	struct i2c_msg msg[2];
+	int err;
+
+	if (len > sizeof(capdev->xfer_buf) - 2)
+		return -EINVAL;
+
+	capdev->xfer_buf[0] = reg;
+	capdev->xfer_buf[1] = len;
+
+	msg[0].addr = client->addr;
+	msg[0].flags = 0;
+	msg[0].buf = capdev->xfer_buf;
+	msg[0].len = 2;
+
+	msg[1].addr = client->addr;
+	msg[1].flags = I2C_M_RD;
+	msg[1].buf = capdev->xfer_buf;
+	msg[1].len = len + 2;
+
+	err = i2c_transfer(client->adapter, msg, ARRAY_SIZE(msg));
+	if (err != ARRAY_SIZE(msg))
+		return err < 0 ? err : -EIO;
+
+	if (capdev->xfer_buf[0] != reg) {
+		dev_err(dev,
+			"I2C read error: register address does not match (%#02x vs %02x)\n",
+			capdev->xfer_buf[0], reg);
+		return -ECOMM;
+	}
+
+	memcpy(data, &capdev->xfer_buf[2], len);
+
+	return 0;
+}
+
+/*
+ * Handle interrupt and report the key changes to the input system.
+ * Multi-touch can be supported; however, it really depends on whether
+ * the device can multi-touch.
+ */
+static irqreturn_t atmel_captouch_isr(int irq, void *data)
+{
+	struct atmel_captouch_device *capdev = data;
+	struct device *dev = &capdev->client->dev;
+	int error;
+	int i;
+	u8 new_btn;
+	u8 changed_btn;
+
+	error = atmel_read(capdev, REG_KEY_STATE, &new_btn, 1);
+	if (error) {
+		dev_err(dev, "failed to read button state: %d\n", error);
+		goto out;
+	}
+
+	dev_dbg(dev, "%s: button state %#02x\n", __func__, new_btn);
+
+	changed_btn = new_btn ^ capdev->prev_btn;
+	capdev->prev_btn = new_btn;
+
+	for (i = 0; i < capdev->num_btn; i++) {
+		if (changed_btn & BIT(i))
+			input_report_key(capdev->input,
+					 capdev->keycodes[i],
+					 new_btn & BIT(i));
+	}
+
+	input_sync(capdev->input);
+
+out:
+	return IRQ_HANDLED;
+}
+
+/*
+ * Probe function to setup the device, input system and interrupt
+ */
+static int atmel_captouch_probe(struct i2c_client *client,
+		const struct i2c_device_id *id)
+{
+	struct atmel_captouch_device *capdev;
+	struct device *dev = &client->dev;
+	struct device_node *node;
+	int i;
+	int err;
+
+	if (!i2c_check_functionality(client->adapter,
+				     I2C_FUNC_SMBUS_BYTE_DATA |
+					I2C_FUNC_SMBUS_WORD_DATA |
+					I2C_FUNC_SMBUS_I2C_BLOCK)) {
+		dev_err(dev, "needed i2c functionality is not supported\n");
+		return -EINVAL;
+	}
+
+	capdev = devm_kzalloc(dev, sizeof(*capdev), GFP_KERNEL);
+	if (!capdev)
+		return -ENOMEM;
+
+	capdev->client = client;
+	i2c_set_clientdata(client, capdev);
+
+	err = atmel_read(capdev, REG_KEY_STATE,
+			    &capdev->prev_btn, sizeof(capdev->prev_btn));
+	if (err) {
+		dev_err(dev, "failed to read initial button state: %d\n", err);
+		return err;
+	}
+
+	capdev->input = devm_input_allocate_device(dev);
+	if (!capdev->input) {
+		dev_err(dev, "failed to allocate input device\n");
+		return -ENOMEM;
+	}
+
+	capdev->input->id.bustype = BUS_I2C;
+	capdev->input->id.product = 0x880A;
+	capdev->input->id.version = 0;
+	capdev->input->name = "ATMegaXX Capacitive Button Controller";
+	__set_bit(EV_KEY, capdev->input->evbit);
+
+	node = dev->of_node;
+	if (!node) {
+		dev_err(dev, "failed to find matching node in device tree\n");
+		return -EINVAL;
+	}
+
+	if (of_property_read_bool(node, "autorepeat"))
+		__set_bit(EV_REP, capdev->input->evbit);
+
+	capdev->num_btn = of_property_count_u32_elems(node, "linux,keymap");
+	if (capdev->num_btn > MAX_NUM_OF_BUTTONS)
+		capdev->num_btn = MAX_NUM_OF_BUTTONS;
+
+	err = of_property_read_u32_array(node, "linux,keycodes",
+					 capdev->keycodes,
+					 capdev->num_btn);
+	if (err) {
+		dev_err(dev,
+			"failed to read linux,keycode property: %d\n", err);
+		return err;
+	}
+
+	for (i = 0; i < capdev->num_btn; i++)
+		__set_bit(capdev->keycodes[i], capdev->input->keybit);
+
+	capdev->input->keycode = capdev->keycodes;
+	capdev->input->keycodesize = sizeof(capdev->keycodes[0]);
+	capdev->input->keycodemax = capdev->num_btn;
+
+	err = input_register_device(capdev->input);
+	if (err)
+		return err;
+
+	err = devm_request_threaded_irq(dev, client->irq,
+					NULL, atmel_captouch_isr,
+					IRQF_ONESHOT,
+					"atmel_captouch", capdev);
+	if (err) {
+		dev_err(dev, "failed to request irq %d: %d\n",
+			client->irq, err);
+		return err;
+	}
+
+	return 0;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id atmel_captouch_of_id[] = {
+	{
+		.compatible = "atmel,captouch",
+	},
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, atmel_captouch_of_id);
+#endif
+
+static const struct i2c_device_id atmel_captouch_id[] = {
+	{ "atmel_captouch", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, atmel_captouch_id);
+
+static struct i2c_driver atmel_captouch_driver = {
+	.probe		= atmel_captouch_probe,
+	.id_table	= atmel_captouch_id,
+	.driver		= {
+		.name	= "atmel_captouch",
+		.of_match_table = of_match_ptr(atmel_captouch_of_id),
+	},
+};
+module_i2c_driver(atmel_captouch_driver);
+
+/* Module information */
+MODULE_AUTHOR("Hung-yu Wu <hywu@google.com>");
+MODULE_DESCRIPTION("Atmel ATmegaXX Capacitance Touch Sensor I2C Driver");
+MODULE_LICENSE("GPL v2");

drivers/input/misc/hisi_powerkey.c

+/*
+ * Hisilicon PMIC powerkey driver
+ *
+ * Copyright (C) 2013 Hisilicon Ltd.
+ * Copyright (C) 2015, 2016 Linaro Ltd.
+ *
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License. See the file "COPYING" in the main directory of this
+ * archive for more details.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/reboot.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_irq.h>
+#include <linux/input.h>
+#include <linux/slab.h>
+
+/* the held interrupt will trigger after 4 seconds */
+#define MAX_HELD_TIME	(4 * MSEC_PER_SEC)
+
+static irqreturn_t hi65xx_power_press_isr(int irq, void *q)
+{
+	struct input_dev *input = q;
+
+	pm_wakeup_event(input->dev.parent, MAX_HELD_TIME);
+	input_report_key(input, KEY_POWER, 1);
+	input_sync(input);
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t hi65xx_power_release_isr(int irq, void *q)
+{
+	struct input_dev *input = q;
+
+	pm_wakeup_event(input->dev.parent, MAX_HELD_TIME);
+	input_report_key(input, KEY_POWER, 0);
+	input_sync(input);
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t hi65xx_restart_toggle_isr(int irq, void *q)
+{
+	struct input_dev *input = q;
+	int value = test_bit(KEY_RESTART, input->key);
+
+	pm_wakeup_event(input->dev.parent, MAX_HELD_TIME);
+	input_report_key(input, KEY_RESTART, !value);
+	input_sync(input);
+
+	return IRQ_HANDLED;
+}
+
+static const struct {
+	const char *name;
+	irqreturn_t (*handler)(int irq, void *q);
+} hi65xx_irq_info[] = {
+	{ "down", hi65xx_power_press_isr },
+	{ "up", hi65xx_power_release_isr },
+	{ "hold 4s", hi65xx_restart_toggle_isr },
+};
+
+static int hi65xx_powerkey_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct input_dev *input;
+	int irq, i, error;
+
+	input = devm_input_allocate_device(&pdev->dev);
+	if (!input) {
+		dev_err(&pdev->dev, "failed to allocate input device\n");
+		return -ENOMEM;
+	}
+
+	input->phys = "hisi_on/input0";
+	input->name = "HISI 65xx PowerOn Key";
+
+	input_set_capability(input, EV_KEY, KEY_POWER);
+	input_set_capability(input, EV_KEY, KEY_RESTART);
+
+	for (i = 0; i < ARRAY_SIZE(hi65xx_irq_info); i++) {
+
+		irq = platform_get_irq_byname(pdev, hi65xx_irq_info[i].name);
+		if (irq < 0) {
+			error = irq;
+			dev_err(dev, "couldn't get irq %s: %d\n",
+				hi65xx_irq_info[i].name, error);
+			return error;
+		}
+
+		error = devm_request_any_context_irq(dev, irq,
+						     hi65xx_irq_info[i].handler,
+						     IRQF_ONESHOT,
+						     hi65xx_irq_info[i].name,
+						     input);
+		if (error < 0) {
+			dev_err(dev, "couldn't request irq %s: %d\n",
+				hi65xx_irq_info[i].name, error);
+			return error;
+		}
+	}
+
+	error = input_register_device(input);
+	if (error) {
+		dev_err(&pdev->dev, "failed to register input device: %d\n",
+			error);
+		return error;
+	}
+
+	device_init_wakeup(&pdev->dev, 1);
+
+	return 0;
+}
+
+static int hi65xx_powerkey_remove(struct platform_device *pdev)
+{
+	device_init_wakeup(&pdev->dev, 0);
+
+	return 0;
+}
+
+static struct platform_driver hi65xx_powerkey_driver = {
+	.driver = {
+		.name = "hi65xx-powerkey",
+	},
+	.probe = hi65xx_powerkey_probe,
+	.remove  = hi65xx_powerkey_remove,
+};
+module_platform_driver(hi65xx_powerkey_driver);
+
+MODULE_AUTHOR("Zhiliang Xue <xuezhiliang@huawei.com");
+MODULE_DESCRIPTION("Hisi PMIC Power key driver");
+MODULE_LICENSE("GPL v2");

drivers/input/misc/regulator-haptic.c

@@ -124,7 +124,7 @@ regulator_haptic_parse_dt(struct device *dev, struct regulator_haptic *haptic)
 
 	node = dev->of_node;
 	if(!node) {
-		dev_err(dev, "Missing dveice tree data\n");
+		dev_err(dev, "Missing device tree data\n");
 		return -EINVAL;
 	}
 

drivers/input/misc/xen-kbdfront.c

@@ -130,8 +130,8 @@ static int xenkbd_probe(struct xenbus_device *dev,
 	if (xenbus_scanf(XBT_NIL, dev->otherend, "feature-abs-pointer", "%d", &abs) < 0)
 		abs = 0;
 	if (abs) {
-		ret = xenbus_printf(XBT_NIL, dev->nodename,
-				    "request-abs-pointer", "1");
+		ret = xenbus_write(XBT_NIL, dev->nodename,
+				   "request-abs-pointer", "1");
 		if (ret) {
 			pr_warning("xenkbd: can't request abs-pointer");
 			abs = 0;
@@ -327,8 +327,8 @@ static void xenkbd_backend_changed(struct xenbus_device *dev,
 		if (ret < 0)
 			val = 0;
 		if (val) {
-			ret = xenbus_printf(XBT_NIL, info->xbdev->nodename,
-					    "request-abs-pointer", "1");
+			ret = xenbus_write(XBT_NIL, info->xbdev->nodename,
+					   "request-abs-pointer", "1");
 			if (ret)
 				pr_warning("xenkbd: can't request abs-pointer");
 		}

drivers/input/mouse/elantech.c

@@ -1708,7 +1708,7 @@ int elantech_init(struct psmouse *psmouse)
 		snprintf(etd->tp_phys, sizeof(etd->tp_phys), "%s/input1",
 			psmouse->ps2dev.serio->phys);
 		tp_dev->phys = etd->tp_phys;
-		tp_dev->name = "Elantech PS/2 TrackPoint";
+		tp_dev->name = "ETPS/2 Elantech TrackPoint";
 		tp_dev->id.bustype = BUS_I8042;
 		tp_dev->id.vendor  = 0x0002;
 		tp_dev->id.product = PSMOUSE_ELANTECH;

drivers/input/mouse/lifebook.c

@@ -287,7 +287,7 @@ static int lifebook_create_relative_device(struct psmouse *psmouse)
 		 "%s/input1", psmouse->ps2dev.serio->phys);
 
 	dev2->phys = priv->phys;
-	dev2->name = "PS/2 Touchpad";
+	dev2->name = "LBPS/2 Fujitsu Lifebook Touchpad";
 	dev2->id.bustype = BUS_I8042;
 	dev2->id.vendor  = 0x0002;
 	dev2->id.product = PSMOUSE_LIFEBOOK;

drivers/input/rmi4/rmi_f01.c

@@ -81,26 +81,26 @@ struct f01_basic_properties {
  * This bit disables whatever sleep mode may be selected by the sleep_mode
  * field and forces the device to run at full power without sleeping.
  */
-#define RMI_F01_CRTL0_NOSLEEP_BIT	BIT(2)
+#define RMI_F01_CTRL0_NOSLEEP_BIT	BIT(2)
 
 /*
  * When this bit is set, the touch controller employs a noise-filtering
  * algorithm designed for use with a connected battery charger.
  */
-#define RMI_F01_CRTL0_CHARGER_BIT	BIT(5)
+#define RMI_F01_CTRL0_CHARGER_BIT	BIT(5)
 
 /*
  * Sets the report rate for the device. The effect of this setting is
  * highly product dependent. Check the spec sheet for your particular
  * touch sensor.
  */
-#define RMI_F01_CRTL0_REPORTRATE_BIT	BIT(6)
+#define RMI_F01_CTRL0_REPORTRATE_BIT	BIT(6)
 
 /*
  * Written by the host as an indicator that the device has been
  * successfully configured.
  */
-#define RMI_F01_CRTL0_CONFIGURED_BIT	BIT(7)
+#define RMI_F01_CTRL0_CONFIGURED_BIT	BIT(7)
 
 /**
  * @ctrl0 - see the bit definitions above.
@@ -330,10 +330,10 @@ static int rmi_f01_probe(struct rmi_function *fn)
 	case RMI_F01_NOSLEEP_DEFAULT:
 		break;
 	case RMI_F01_NOSLEEP_OFF:
-		f01->device_control.ctrl0 &= ~RMI_F01_CRTL0_NOSLEEP_BIT;
+		f01->device_control.ctrl0 &= ~RMI_F01_CTRL0_NOSLEEP_BIT;
 		break;
 	case RMI_F01_NOSLEEP_ON:
-		f01->device_control.ctrl0 |= RMI_F01_CRTL0_NOSLEEP_BIT;
+		f01->device_control.ctrl0 |= RMI_F01_CTRL0_NOSLEEP_BIT;
 		break;
 	}
 
@@ -349,7 +349,7 @@ static int rmi_f01_probe(struct rmi_function *fn)
 		f01->device_control.ctrl0 &= ~RMI_F01_CTRL0_SLEEP_MODE_MASK;
 	}
 
-	f01->device_control.ctrl0 |= RMI_F01_CRTL0_CONFIGURED_BIT;
+	f01->device_control.ctrl0 |= RMI_F01_CTRL0_CONFIGURED_BIT;
 
 	error = rmi_write(rmi_dev, fn->fd.control_base_addr,
 			  f01->device_control.ctrl0);
@@ -535,8 +535,8 @@ static int rmi_f01_suspend(struct rmi_function *fn)
 	int error;
 
 	f01->old_nosleep =
-		f01->device_control.ctrl0 & RMI_F01_CRTL0_NOSLEEP_BIT;
-	f01->device_control.ctrl0 &= ~RMI_F01_CRTL0_NOSLEEP_BIT;
+		f01->device_control.ctrl0 & RMI_F01_CTRL0_NOSLEEP_BIT;
+	f01->device_control.ctrl0 &= ~RMI_F01_CTRL0_NOSLEEP_BIT;
 
 	f01->device_control.ctrl0 &= ~RMI_F01_CTRL0_SLEEP_MODE_MASK;
 	if (device_may_wakeup(fn->rmi_dev->xport->dev))
@@ -549,7 +549,7 @@ static int rmi_f01_suspend(struct rmi_function *fn)
 	if (error) {
 		dev_err(&fn->dev, "Failed to write sleep mode: %d.\n", error);
 		if (f01->old_nosleep)
-			f01->device_control.ctrl0 |= RMI_F01_CRTL0_NOSLEEP_BIT;
+			f01->device_control.ctrl0 |= RMI_F01_CTRL0_NOSLEEP_BIT;
 		f01->device_control.ctrl0 &= ~RMI_F01_CTRL0_SLEEP_MODE_MASK;
 		f01->device_control.ctrl0 |= RMI_SLEEP_MODE_NORMAL;
 		return error;
@@ -564,7 +564,7 @@ static int rmi_f01_resume(struct rmi_function *fn)
 	int error;
 
 	if (f01->old_nosleep)
-		f01->device_control.ctrl0 |= RMI_F01_CRTL0_NOSLEEP_BIT;
+		f01->device_control.ctrl0 |= RMI_F01_CTRL0_NOSLEEP_BIT;
 
 	f01->device_control.ctrl0 &= ~RMI_F01_CTRL0_SLEEP_MODE_MASK;
 	f01->device_control.ctrl0 |= RMI_SLEEP_MODE_NORMAL;

drivers/input/rmi4/rmi_f11.c

@@ -530,8 +530,8 @@ static void rmi_f11_rel_pos_report(struct f11_data *f11, u8 n_finger)
 	struct f11_2d_data *data = &f11->data;
 	s8 x, y;
 
-	x = data->rel_pos[n_finger * 2];
-	y = data->rel_pos[n_finger * 2 + 1];
+	x = data->rel_pos[n_finger * RMI_F11_REL_BYTES];
+	y = data->rel_pos[n_finger * RMI_F11_REL_BYTES + 1];
 
 	rmi_2d_sensor_rel_report(sensor, x, y);
 }
@@ -1241,7 +1241,6 @@ static int rmi_f11_attention(struct rmi_function *fn, unsigned long *irq_bits)
 	struct rmi_driver_data *drvdata = dev_get_drvdata(&rmi_dev->dev);
 	struct f11_data *f11 = dev_get_drvdata(&fn->dev);
 	u16 data_base_addr = fn->fd.data_base_addr;
-	u16 data_base_addr_offset = 0;
 	int error;
 
 	if (rmi_dev->xport->attn_data) {
@@ -1251,8 +1250,7 @@ static int rmi_f11_attention(struct rmi_function *fn, unsigned long *irq_bits)
 		rmi_dev->xport->attn_size -= f11->sensor.attn_size;
 	} else {
 		error = rmi_read_block(rmi_dev,
-				data_base_addr + data_base_addr_offset,
-				f11->sensor.data_pkt,
+				data_base_addr, f11->sensor.data_pkt,
 				f11->sensor.pkt_size);
 		if (error < 0)
 			return error;
@@ -1260,7 +1258,6 @@ static int rmi_f11_attention(struct rmi_function *fn, unsigned long *irq_bits)
 
 	rmi_f11_finger_handler(f11, &f11->sensor, irq_bits,
 				drvdata->num_of_irq_regs);
-	data_base_addr_offset += f11->sensor.pkt_size;
 
 	return 0;
 }

drivers/input/rmi4/rmi_f12.c

@@ -27,7 +27,6 @@ enum rmi_f12_object_type {
 };
 
 struct f12_data {
-	struct rmi_function *fn;
 	struct rmi_2d_sensor sensor;
 	struct rmi_2d_sensor_platform_data sensor_pdata;
 

drivers/input/rmi4/rmi_i2c.c

@@ -11,6 +11,8 @@
 #include <linux/rmi.h>
 #include <linux/irq.h>
 #include <linux/of.h>
+#include <linux/delay.h>
+#include <linux/regulator/consumer.h>
 #include "rmi_driver.h"
 
 #define BUFFER_SIZE_INCREMENT 32
@@ -37,6 +39,9 @@ struct rmi_i2c_xport {
 
 	u8 *tx_buf;
 	size_t tx_buf_size;
+
+	struct regulator_bulk_data supplies[2];
+	u32 startup_delay;
 };
 
 #define RMI_PAGE_SELECT_REGISTER 0xff
@@ -246,6 +251,24 @@ static int rmi_i2c_probe(struct i2c_client *client,
 		return -ENODEV;
 	}
 
+	rmi_i2c->supplies[0].supply = "vdd";
+	rmi_i2c->supplies[1].supply = "vio";
+	retval = devm_regulator_bulk_get(&client->dev,
+					 ARRAY_SIZE(rmi_i2c->supplies),
+					 rmi_i2c->supplies);
+	if (retval < 0)
+		return retval;
+
+	retval = regulator_bulk_enable(ARRAY_SIZE(rmi_i2c->supplies),
+				       rmi_i2c->supplies);
+	if (retval < 0)
+		return retval;
+
+	of_property_read_u32(client->dev.of_node, "syna,startup-delay-ms",
+			     &rmi_i2c->startup_delay);
+
+	msleep(rmi_i2c->startup_delay);
+
 	rmi_i2c->client = client;
 	mutex_init(&rmi_i2c->page_mutex);
 
@@ -286,6 +309,8 @@ static int rmi_i2c_remove(struct i2c_client *client)
 	struct rmi_i2c_xport *rmi_i2c = i2c_get_clientdata(client);
 
 	rmi_unregister_transport_device(&rmi_i2c->xport);
+	regulator_bulk_disable(ARRAY_SIZE(rmi_i2c->supplies),
+			       rmi_i2c->supplies);
 
 	return 0;
 }
@@ -308,6 +333,10 @@ static int rmi_i2c_suspend(struct device *dev)
 			dev_warn(dev, "Failed to enable irq for wake: %d\n",
 				ret);
 	}
+
+	regulator_bulk_disable(ARRAY_SIZE(rmi_i2c->supplies),
+			       rmi_i2c->supplies);
+
 	return ret;
 }
 
@@ -317,6 +346,13 @@ static int rmi_i2c_resume(struct device *dev)
 	struct rmi_i2c_xport *rmi_i2c = i2c_get_clientdata(client);
 	int ret;
 
+	ret = regulator_bulk_enable(ARRAY_SIZE(rmi_i2c->supplies),
+				    rmi_i2c->supplies);
+	if (ret)
+		return ret;
+
+	msleep(rmi_i2c->startup_delay);
+
 	enable_irq(rmi_i2c->irq);
 	if (device_may_wakeup(&client->dev)) {
 		ret = disable_irq_wake(rmi_i2c->irq);
@@ -346,6 +382,9 @@ static int rmi_i2c_runtime_suspend(struct device *dev)
 
 	disable_irq(rmi_i2c->irq);
 
+	regulator_bulk_disable(ARRAY_SIZE(rmi_i2c->supplies),
+			       rmi_i2c->supplies);
+
 	return 0;
 }
 
@@ -355,6 +394,13 @@ static int rmi_i2c_runtime_resume(struct device *dev)
 	struct rmi_i2c_xport *rmi_i2c = i2c_get_clientdata(client);
 	int ret;
 
+	ret = regulator_bulk_enable(ARRAY_SIZE(rmi_i2c->supplies),
+				    rmi_i2c->supplies);
+	if (ret)
+		return ret;
+
+	msleep(rmi_i2c->startup_delay);
+
 	enable_irq(rmi_i2c->irq);
 
 	ret = rmi_driver_resume(rmi_i2c->xport.rmi_dev);

drivers/input/serio/ams_delta_serio.c

@@ -56,7 +56,7 @@ static int check_data(int data)
 	/* it should be odd */
 	if (!(parity & 0x01)) {
 		dev_warn(&ams_delta_serio->dev,
-				"paritiy check failed, data=0x%X parity=0x%X\n",
+				"parity check failed, data=0x%X parity=0x%X\n",
 				data, parity);
 		return SERIO_PARITY;
 	}

drivers/input/tablet/Kconfig

@@ -73,6 +73,21 @@ config TABLET_USB_KBTAB
 	  To compile this driver as a module, choose M here: the
 	  module will be called kbtab.
 
+config TABLET_USB_PEGASUS
+	tristate "Pegasus Mobile Notetaker Pen input tablet support"
+	depends on USB_ARCH_HAS_HCD
+	select USB
+	help
+	  Say Y here if you want to use the Pegasus Mobile Notetaker,
+	  also known as:
+	  Genie e-note The Notetaker,
+	  Staedtler Digital ballpoint pen 990 01,
+	  IRISnotes Express or
+	  NEWLink Digital Note Taker.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called pegasus_notetaker.
+
 config TABLET_SERIAL_WACOM4
 	tristate "Wacom protocol 4 serial tablet support"
 	select SERIO

drivers/input/tablet/Makefile

@@ -8,4 +8,5 @@ obj-$(CONFIG_TABLET_USB_AIPTEK)	+= aiptek.o
 obj-$(CONFIG_TABLET_USB_GTCO)	+= gtco.o
 obj-$(CONFIG_TABLET_USB_HANWANG) += hanwang.o
 obj-$(CONFIG_TABLET_USB_KBTAB)	+= kbtab.o
+obj-$(CONFIG_TABLET_USB_PEGASUS) += pegasus_notetaker.o
 obj-$(CONFIG_TABLET_SERIAL_WACOM4) += wacom_serial4.o

drivers/input/touchscreen/Kconfig

@@ -632,7 +632,7 @@ config TOUCHSCREEN_EDT_FT5X06
 
 config TOUCHSCREEN_MIGOR
 	tristate "Renesas MIGO-R touchscreen"
-	depends on SH_MIGOR && I2C
+	depends on (SH_MIGOR || COMPILE_TEST) && I2C
 	help
 	  Say Y here to enable MIGO-R touchscreen support.
 
@@ -1046,6 +1046,19 @@ config TOUCHSCREEN_PCAP
 	  To compile this driver as a module, choose M here: the
 	  module will be called pcap_ts.
 
+config TOUCHSCREEN_RM_TS
+	tristate "Raydium I2C Touchscreen"
+	depends on I2C
+	depends on GPIOLIB || COMPILE_TEST
+	help
+	  Say Y here if you have Raydium series I2C touchscreen,
+	  such as RM32380, connected to your system.
+
+	  If unsure, say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called raydium_i2c_ts.
+
 config TOUCHSCREEN_ST1232
 	tristate "Sitronix ST1232 touchscreen controllers"
 	depends on I2C
@@ -1094,6 +1107,19 @@ config TOUCHSCREEN_SUR40
 	  To compile this driver as a module, choose M here: the
 	  module will be called sur40.
 
+config TOUCHSCREEN_SURFACE3_SPI
+	tristate "Ntrig/Microsoft Surface 3 SPI touchscreen"
+	depends on SPI
+	depends on GPIOLIB || COMPILE_TEST
+	help
+	  Say Y here if you have the Ntrig/Microsoft SPI touchscreen
+	  controller chip as found on the Surface 3 in your system.
+
+	  If unsure, say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called surface3_spi.
+
 config TOUCHSCREEN_SX8654
 	tristate "Semtech SX8654 touchscreen"
 	depends on I2C

drivers/input/touchscreen/Makefile

@@ -62,11 +62,13 @@ obj-$(CONFIG_TOUCHSCREEN_USB_COMPOSITE)	+= usbtouchscreen.o
 obj-$(CONFIG_TOUCHSCREEN_PCAP)		+= pcap_ts.o
 obj-$(CONFIG_TOUCHSCREEN_PENMOUNT)	+= penmount.o
 obj-$(CONFIG_TOUCHSCREEN_PIXCIR)	+= pixcir_i2c_ts.o
+obj-$(CONFIG_TOUCHSCREEN_RM_TS)		+= raydium_i2c_ts.o
 obj-$(CONFIG_TOUCHSCREEN_S3C2410)	+= s3c2410_ts.o
 obj-$(CONFIG_TOUCHSCREEN_ST1232)	+= st1232.o
 obj-$(CONFIG_TOUCHSCREEN_STMPE)		+= stmpe-ts.o
 obj-$(CONFIG_TOUCHSCREEN_SUN4I)		+= sun4i-ts.o
 obj-$(CONFIG_TOUCHSCREEN_SUR40)		+= sur40.o
+obj-$(CONFIG_TOUCHSCREEN_SURFACE3_SPI)	+= surface3_spi.o
 obj-$(CONFIG_TOUCHSCREEN_TI_AM335X_TSC)	+= ti_am335x_tsc.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHIT213)	+= touchit213.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHRIGHT)	+= touchright.o

drivers/input/touchscreen/ad7879.c

@@ -595,7 +595,7 @@ struct ad7879 *ad7879_probe(struct device *dev, u8 devid, unsigned int irq,
 	} else {
 		input_set_abs_params(input_dev, ABS_X, 0, MAX_12BIT, 0, 0);
 		input_set_abs_params(input_dev, ABS_Y, 0, MAX_12BIT, 0, 0);
-		touchscreen_parse_properties(input_dev, false);
+		touchscreen_parse_properties(input_dev, false, NULL);
 		if (!input_abs_get_max(input_dev, ABS_PRESSURE)) {
 			dev_err(dev, "Touchscreen pressure is not specified\n");
 			return ERR_PTR(-EINVAL);

drivers/input/touchscreen/chipone_icn8318.c

@@ -17,6 +17,7 @@
 #include <linux/i2c.h>
 #include <linux/input.h>
 #include <linux/input/mt.h>
+#include <linux/input/touchscreen.h>
 #include <linux/module.h>
 #include <linux/of.h>
 
@@ -52,11 +53,7 @@ struct icn8318_data {
 	struct i2c_client *client;
 	struct input_dev *input;
 	struct gpio_desc *wake_gpio;
-	u32 max_x;
-	u32 max_y;
-	bool invert_x;
-	bool invert_y;
-	bool swap_x_y;
+	struct touchscreen_properties prop;
 };
 
 static int icn8318_read_touch_data(struct i2c_client *client,
@@ -91,7 +88,7 @@ static irqreturn_t icn8318_irq(int irq, void *dev_id)
 	struct icn8318_data *data = dev_id;
 	struct device *dev = &data->client->dev;
 	struct icn8318_touch_data touch_data;
-	int i, ret, x, y;
+	int i, ret;
 
 	ret = icn8318_read_touch_data(data->client, &touch_data);
 	if (ret < 0) {
@@ -124,22 +121,9 @@ static irqreturn_t icn8318_irq(int irq, void *dev_id)
 		if (!act)
 			continue;
 
-		x = be16_to_cpu(touch->x);
-		y = be16_to_cpu(touch->y);
-
-		if (data->invert_x)
-			x = data->max_x - x;
-
-		if (data->invert_y)
-			y = data->max_y - y;
-
-		if (!data->swap_x_y) {
-			input_event(data->input, EV_ABS, ABS_MT_POSITION_X, x);
-			input_event(data->input, EV_ABS, ABS_MT_POSITION_Y, y);
-		} else {
-			input_event(data->input, EV_ABS, ABS_MT_POSITION_X, y);
-			input_event(data->input, EV_ABS, ABS_MT_POSITION_Y, x);
-		}
+		touchscreen_report_pos(data->input, &data->prop,
+				       be16_to_cpu(touch->x),
+				       be16_to_cpu(touch->y), true);
 	}
 
 	input_mt_sync_frame(data->input);
@@ -200,10 +184,8 @@ static int icn8318_probe(struct i2c_client *client,
 			 const struct i2c_device_id *id)
 {
 	struct device *dev = &client->dev;
-	struct device_node *np = dev->of_node;
 	struct icn8318_data *data;
 	struct input_dev *input;
-	u32 fuzz_x = 0, fuzz_y = 0;
 	int error;
 
 	if (!client->irq) {
@@ -223,19 +205,6 @@ static int icn8318_probe(struct i2c_client *client,
 		return error;
 	}
 
-	if (of_property_read_u32(np, "touchscreen-size-x", &data->max_x) ||
-	    of_property_read_u32(np, "touchscreen-size-y", &data->max_y)) {
-		dev_err(dev, "Error touchscreen-size-x and/or -y missing\n");
-		return -EINVAL;
-	}
-
-	/* Optional */
-	of_property_read_u32(np, "touchscreen-fuzz-x", &fuzz_x);
-	of_property_read_u32(np, "touchscreen-fuzz-y", &fuzz_y);
-	data->invert_x = of_property_read_bool(np, "touchscreen-inverted-x");
-	data->invert_y = of_property_read_bool(np, "touchscreen-inverted-y");
-	data->swap_x_y = of_property_read_bool(np, "touchscreen-swapped-x-y");
-
 	input = devm_input_allocate_device(dev);
 	if (!input)
 		return -ENOMEM;
@@ -246,16 +215,14 @@ static int icn8318_probe(struct i2c_client *client,
 	input->close = icn8318_stop;
 	input->dev.parent = dev;
 
-	if (!data->swap_x_y) {
-		input_set_abs_params(input, ABS_MT_POSITION_X, 0,
-				     data->max_x, fuzz_x, 0);
-		input_set_abs_params(input, ABS_MT_POSITION_Y, 0,
-				     data->max_y, fuzz_y, 0);
-	} else {
-		input_set_abs_params(input, ABS_MT_POSITION_X, 0,
-				     data->max_y, fuzz_y, 0);
-		input_set_abs_params(input, ABS_MT_POSITION_Y, 0,
-				     data->max_x, fuzz_x, 0);
+	input_set_capability(input, EV_ABS, ABS_MT_POSITION_X);
+	input_set_capability(input, EV_ABS, ABS_MT_POSITION_Y);
+
+	touchscreen_parse_properties(input, true, &data->prop);
+	if (!input_abs_get_max(input, ABS_MT_POSITION_X) ||
+	    !input_abs_get_max(input, ABS_MT_POSITION_Y)) {
+		dev_err(dev, "Error touchscreen-size-x and/or -y missing\n");
+		return -EINVAL;
 	}
 
 	error = input_mt_init_slots(input, ICN8318_MAX_TOUCHES,

drivers/input/touchscreen/cyttsp_core.c

@@ -657,7 +657,7 @@ struct cyttsp *cyttsp_probe(const struct cyttsp_bus_ops *bus_ops,
 
 	input_set_capability(input_dev, EV_ABS, ABS_MT_POSITION_X);
 	input_set_capability(input_dev, EV_ABS, ABS_MT_POSITION_Y);
-	touchscreen_parse_properties(input_dev, true);
+	touchscreen_parse_properties(input_dev, true, NULL);
 
 	error = input_mt_init_slots(input_dev, CY_MAX_ID, 0);
 	if (error) {

drivers/input/touchscreen/edt-ft5x06.c

@@ -86,6 +86,7 @@ struct edt_reg_addr {
 struct edt_ft5x06_ts_data {
 	struct i2c_client *client;
 	struct input_dev *input;
+	struct touchscreen_properties prop;
 	u16 num_x;
 	u16 num_y;
 
@@ -246,8 +247,8 @@ static irqreturn_t edt_ft5x06_ts_isr(int irq, void *dev_id)
 		if (!down)
 			continue;
 
-		input_report_abs(tsdata->input, ABS_MT_POSITION_X, x);
-		input_report_abs(tsdata->input, ABS_MT_POSITION_Y, y);
+		touchscreen_report_pos(tsdata->input, &tsdata->prop, x, y,
+				       true);
 	}
 
 	input_mt_report_pointer_emulation(tsdata->input, true);
@@ -972,7 +973,7 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
 	input_set_abs_params(input, ABS_MT_POSITION_Y,
 			     0, tsdata->num_y * 64 - 1, 0, 0);
 
-	touchscreen_parse_properties(input, true);
+	touchscreen_parse_properties(input, true, &tsdata->prop);
 
 	error = input_mt_init_slots(input, tsdata->max_support_points,
 				INPUT_MT_DIRECT);

drivers/input/touchscreen/migor_ts.c

@@ -202,7 +202,7 @@ static int migor_ts_remove(struct i2c_client *client)
 	return 0;
 }
 
-static int migor_ts_suspend(struct device *dev)
+static int __maybe_unused migor_ts_suspend(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct migor_ts_priv *priv = i2c_get_clientdata(client);
@@ -213,7 +213,7 @@ static int migor_ts_suspend(struct device *dev)
 	return 0;
 }
 
-static int migor_ts_resume(struct device *dev)
+static int __maybe_unused migor_ts_resume(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct migor_ts_priv *priv = i2c_get_clientdata(client);
@@ -230,7 +230,7 @@ static const struct i2c_device_id migor_ts_id[] = {
 	{ "migor_ts", 0 },
 	{ }
 };
-MODULE_DEVICE_TABLE(i2c, migor_ts);
+MODULE_DEVICE_TABLE(i2c, migor_ts_id);
 
 static struct i2c_driver migor_ts_driver = {
 	.driver = {

drivers/input/touchscreen/of_touchscreen.c

@@ -55,12 +55,16 @@ static void touchscreen_set_params(struct input_dev *dev,
  * @input: input device that should be parsed
  * @multitouch: specifies whether parsed properties should be applied to
  *	single-touch or multi-touch axes
+ * @prop: pointer to a struct touchscreen_properties into which to store
+ *	axis swap and invert info for use with touchscreen_report_x_y();
+ *	or %NULL
  *
  * This function parses common DT properties for touchscreens and setups the
  * input device accordingly. The function keeps previously set up default
  * values if no value is specified via DT.
  */
-void touchscreen_parse_properties(struct input_dev *input, bool multitouch)
+void touchscreen_parse_properties(struct input_dev *input, bool multitouch,
+				  struct touchscreen_properties *prop)
 {
 	struct device *dev = input->dev.parent;
 	unsigned int axis;
@@ -104,5 +108,80 @@ void touchscreen_parse_properties(struct input_dev *input, bool multitouch)
 						&fuzz);
 	if (data_present)
 		touchscreen_set_params(input, axis, maximum, fuzz);
+
+	if (!prop)
+		return;
+
+	axis = multitouch ? ABS_MT_POSITION_X : ABS_X;
+
+	prop->max_x = input_abs_get_max(input, axis);
+	prop->max_y = input_abs_get_max(input, axis + 1);
+	prop->invert_x =
+		device_property_read_bool(dev, "touchscreen-inverted-x");
+	prop->invert_y =
+		device_property_read_bool(dev, "touchscreen-inverted-y");
+	prop->swap_x_y =
+		device_property_read_bool(dev, "touchscreen-swapped-x-y");
+
+	if (prop->swap_x_y)
+		swap(input->absinfo[axis], input->absinfo[axis + 1]);
 }
 EXPORT_SYMBOL(touchscreen_parse_properties);
+
+static void
+touchscreen_apply_prop_to_x_y(const struct touchscreen_properties *prop,
+			      unsigned int *x, unsigned int *y)
+{
+	if (prop->invert_x)
+		*x = prop->max_x - *x;
+
+	if (prop->invert_y)
+		*y = prop->max_y - *y;
+
+	if (prop->swap_x_y)
+		swap(*x, *y);
+}
+
+/**
+ * touchscreen_set_mt_pos - Set input_mt_pos coordinates
+ * @pos: input_mt_pos to set coordinates of
+ * @prop: pointer to a struct touchscreen_properties
+ * @x: X coordinate to store in pos
+ * @y: Y coordinate to store in pos
+ *
+ * Adjust the passed in x and y values applying any axis inversion and
+ * swapping requested in the passed in touchscreen_properties and store
+ * the result in a struct input_mt_pos.
+ */
+void touchscreen_set_mt_pos(struct input_mt_pos *pos,
+			    const struct touchscreen_properties *prop,
+			    unsigned int x, unsigned int y)
+{
+	touchscreen_apply_prop_to_x_y(prop, &x, &y);
+	pos->x = x;
+	pos->y = y;
+}
+EXPORT_SYMBOL(touchscreen_set_mt_pos);
+
+/**
+ * touchscreen_report_pos - Report touchscreen coordinates
+ * @input: input_device to report coordinates for
+ * @prop: pointer to a struct touchscreen_properties
+ * @x: X coordinate to report
+ * @y: Y coordinate to report
+ * @multitouch: Report coordinates on single-touch or multi-touch axes
+ *
+ * Adjust the passed in x and y values applying any axis inversion and
+ * swapping requested in the passed in touchscreen_properties and then
+ * report the resulting coordinates on the input_dev's x and y axis.
+ */
+void touchscreen_report_pos(struct input_dev *input,
+			    const struct touchscreen_properties *prop,
+			    unsigned int x, unsigned int y,
+			    bool multitouch)
+{
+	touchscreen_apply_prop_to_x_y(prop, &x, &y);
+	input_report_abs(input, multitouch ? ABS_MT_POSITION_X : ABS_X, x);
+	input_report_abs(input, multitouch ? ABS_MT_POSITION_Y : ABS_Y, y);
+}
+EXPORT_SYMBOL(touchscreen_report_pos);

drivers/input/touchscreen/pixcir_i2c_ts.c

@@ -27,9 +27,9 @@
 #include <linux/input/touchscreen.h>
 #include <linux/gpio.h>
 #include <linux/gpio/consumer.h>
-/*#include <linux/of.h>*/
 #include <linux/of_device.h>
 #include <linux/platform_data/pixcir_i2c_ts.h>
+#include <asm/unaligned.h>
 
 #define PIXCIR_MAX_SLOTS       5 /* Max fingers supported by driver */
 
@@ -41,19 +41,15 @@ struct pixcir_i2c_ts_data {
 	struct gpio_desc *gpio_enable;
 	struct gpio_desc *gpio_wake;
 	const struct pixcir_i2c_chip_data *chip;
+	struct touchscreen_properties prop;
 	int max_fingers;	/* Max fingers supported in this instance */
 	bool running;
 };
 
-struct pixcir_touch {
-	int x;
-	int y;
-	int id;
-};
-
 struct pixcir_report_data {
 	int num_touches;
-	struct pixcir_touch touches[PIXCIR_MAX_SLOTS];
+	struct input_mt_pos pos[PIXCIR_MAX_SLOTS];
+	int ids[PIXCIR_MAX_SLOTS];
 };
 
 static void pixcir_ts_parse(struct pixcir_i2c_ts_data *tsdata,
@@ -98,11 +94,11 @@ static void pixcir_ts_parse(struct pixcir_i2c_ts_data *tsdata,
 	bufptr = &rdbuf[2];
 
 	for (i = 0; i < touch; i++) {
-		report->touches[i].x = (bufptr[1] << 8) | bufptr[0];
-		report->touches[i].y = (bufptr[3] << 8) | bufptr[2];
-
+		touchscreen_set_mt_pos(&report->pos[i], &tsdata->prop,
+				       get_unaligned_le16(bufptr),
+				       get_unaligned_le16(bufptr + 2));
 		if (chip->has_hw_ids) {
-			report->touches[i].id = bufptr[4];
+			report->ids[i] = bufptr[4];
 			bufptr = bufptr + 5;
 		} else {
 			bufptr = bufptr + 4;
@@ -113,9 +109,7 @@ static void pixcir_ts_parse(struct pixcir_i2c_ts_data *tsdata,
 static void pixcir_ts_report(struct pixcir_i2c_ts_data *ts,
 			     struct pixcir_report_data *report)
 {
-	struct input_mt_pos pos[PIXCIR_MAX_SLOTS];
 	int slots[PIXCIR_MAX_SLOTS];
-	struct pixcir_touch *touch;
 	int n, i, slot;
 	struct device *dev = &ts->client->dev;
 	const struct pixcir_i2c_chip_data *chip = ts->chip;
@@ -124,24 +118,16 @@ static void pixcir_ts_report(struct pixcir_i2c_ts_data *ts,
 	if (n > PIXCIR_MAX_SLOTS)
 		n = PIXCIR_MAX_SLOTS;
 
-	if (!ts->chip->has_hw_ids) {
-		for (i = 0; i < n; i++) {
-			touch = &report->touches[i];
-			pos[i].x = touch->x;
-			pos[i].y = touch->y;
-		}
-
-		input_mt_assign_slots(ts->input, slots, pos, n, 0);
-	}
+	if (!ts->chip->has_hw_ids)
+		input_mt_assign_slots(ts->input, slots, report->pos, n, 0);
 
 	for (i = 0; i < n; i++) {
-		touch = &report->touches[i];
-
 		if (chip->has_hw_ids) {
-			slot = input_mt_get_slot_by_key(ts->input, touch->id);
+			slot = input_mt_get_slot_by_key(ts->input,
+							report->ids[i]);
 			if (slot < 0) {
 				dev_dbg(dev, "no free slot for id 0x%x\n",
-					touch->id);
+					report->ids[i]);
 				continue;
 			}
 		} else {
@@ -149,14 +135,15 @@ static void pixcir_ts_report(struct pixcir_i2c_ts_data *ts,
 		}
 
 		input_mt_slot(ts->input, slot);
-		input_mt_report_slot_state(ts->input,
-					   MT_TOOL_FINGER, true);
+		input_mt_report_slot_state(ts->input, MT_TOOL_FINGER, true);
 
-		input_event(ts->input, EV_ABS, ABS_MT_POSITION_X, touch->x);
-		input_event(ts->input, EV_ABS, ABS_MT_POSITION_Y, touch->y);
+		input_report_abs(ts->input, ABS_MT_POSITION_X,
+				 report->pos[i].x);
+		input_report_abs(ts->input, ABS_MT_POSITION_Y,
+				 report->pos[i].y);
 
 		dev_dbg(dev, "%d: slot %d, x %d, y %d\n",
-			i, slot, touch->x, touch->y);
+			i, slot, report->pos[i].x, report->pos[i].y);
 	}
 
 	input_mt_sync_frame(ts->input);
@@ -515,7 +502,7 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client,
 	} else {
 		input_set_capability(input, EV_ABS, ABS_MT_POSITION_X);
 		input_set_capability(input, EV_ABS, ABS_MT_POSITION_Y);
-		touchscreen_parse_properties(input, true);
+		touchscreen_parse_properties(input, true, &tsdata->prop);
 		if (!input_abs_get_max(input, ABS_MT_POSITION_X) ||
 		    !input_abs_get_max(input, ABS_MT_POSITION_Y)) {
 			dev_err(dev, "Touchscreen size is not specified\n");

drivers/input/touchscreen/ti_am335x_tsc.c

@@ -406,7 +406,7 @@ static int titsc_probe(struct platform_device *pdev)
 	int err;
 
 	/* Allocate memory for device */
-	ts_dev = kzalloc(sizeof(struct titsc), GFP_KERNEL);
+	ts_dev = kzalloc(sizeof(*ts_dev), GFP_KERNEL);
 	input_dev = input_allocate_device();
 	if (!ts_dev || !input_dev) {
 		dev_err(&pdev->dev, "failed to allocate memory.\n");

drivers/input/touchscreen/tsc200x-core.c

@@ -568,7 +568,7 @@ int tsc200x_probe(struct device *dev, int irq, const struct input_id *tsc_id,
 	input_set_abs_params(input_dev, ABS_PRESSURE, 0, max_p, fudge_p, 0);
 
 	if (np)
-		touchscreen_parse_properties(input_dev, false);
+		touchscreen_parse_properties(input_dev, false, NULL);
 
 	input_dev->open = tsc200x_open;
 	input_dev->close = tsc200x_close;

drivers/input/touchscreen/wacom_w8001.c

@@ -518,13 +518,21 @@ static int w8001_setup_touch(struct w8001 *w8001, char *basename,
 		w8001->pktlen = W8001_PKTLEN_TOUCH2FG;
 
 		__set_bit(BTN_TOOL_DOUBLETAP, dev->keybit);
-		input_mt_init_slots(dev, 2, 0);
+		error = input_mt_init_slots(dev, 2, 0);
+		if (error) {
+			dev_err(&w8001->serio->dev,
+				"failed to initialize MT slots: %d\n", error);
+			return error;
+		}
+
 		input_set_abs_params(dev, ABS_MT_POSITION_X,
 					0, touch.x, 0, 0);
 		input_set_abs_params(dev, ABS_MT_POSITION_Y,
 					0, touch.y, 0, 0);
 		input_set_abs_params(dev, ABS_MT_TOOL_TYPE,
 					0, MT_TOOL_MAX, 0, 0);
+		input_abs_set_res(dev, ABS_MT_POSITION_X, touch.panel_res);
+		input_abs_set_res(dev, ABS_MT_POSITION_Y, touch.panel_res);
 
 		strlcat(basename, " 2FG", basename_sz);
 		if (w8001->max_pen_x && w8001->max_pen_y)

drivers/tty/vt/keyboard.c

@@ -1733,16 +1733,10 @@ int vt_do_diacrit(unsigned int cmd, void __user *udp, int perm)
 			return -EINVAL;
 
 		if (ct) {
-			buf = kmalloc(ct * sizeof(struct kbdiacruc),
-								GFP_KERNEL);
-			if (buf == NULL)
-				return -ENOMEM;
-
-			if (copy_from_user(buf, a->kbdiacruc,
-					ct * sizeof(struct kbdiacruc))) {
-				kfree(buf);
-				return -EFAULT;
-			}
+			buf = memdup_user(a->kbdiacruc,
+					  ct * sizeof(struct kbdiacruc));
+			if (IS_ERR(buf))
+				return PTR_ERR(buf);
 		} 
 		spin_lock_irqsave(&kbd_event_lock, flags);
 		if (ct)

include/linux/input.h

@@ -95,7 +95,7 @@ struct input_value {
  * @grab: input handle that currently has the device grabbed (via
  *	EVIOCGRAB ioctl). When a handle grabs a device it becomes sole
  *	recipient for all input events coming from the device
- * @event_lock: this spinlock is is taken when input core receives
+ * @event_lock: this spinlock is taken when input core receives
  *	and processes a new event for the device (in input_event()).
  *	Code that accesses and/or modifies parameters of a device
  *	(such as keymap or absmin, absmax, absfuzz, etc.) after device

include/linux/input/touchscreen.h

@@ -10,7 +10,26 @@
 #define _TOUCHSCREEN_H
 
 struct input_dev;
+struct input_mt_pos;
 
-void touchscreen_parse_properties(struct input_dev *dev, bool multitouch);
+struct touchscreen_properties {
+	unsigned int max_x;
+	unsigned int max_y;
+	bool invert_x;
+	bool invert_y;
+	bool swap_x_y;
+};
+
+void touchscreen_parse_properties(struct input_dev *input, bool multitouch,
+				  struct touchscreen_properties *prop);
+
+void touchscreen_set_mt_pos(struct input_mt_pos *pos,
+			    const struct touchscreen_properties *prop,
+			    unsigned int x, unsigned int y);
+
+void touchscreen_report_pos(struct input_dev *input,
+			    const struct touchscreen_properties *prop,
+			    unsigned int x, unsigned int y,
+			    bool multitouch);
 
 #endif