Merge remote-tracking branches 'asoc/topic/rt5659', 'asoc/topic/rt5660',...

Merge remote-tracking branches 'asoc/topic/rt5659', 'asoc/topic/rt5660', 'asoc/topic/rt5677' and 'asoc/topic/samsung' into asoc-next

Documentation/devicetree/bindings/sound/rt5659.txt

@@ -12,6 +12,9 @@ Required properties:
 
 Optional properties:
 
+- clocks: The phandle of the master clock to the CODEC
+- clock-names: Should be "mclk"
+
 - realtek,in1-differential
 - realtek,in3-differential
 - realtek,in4-differential

Documentation/devicetree/bindings/sound/rt5660.txt

+RT5660 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+- compatible : "realtek,rt5660".
+
+- reg : The I2C address of the device.
+
+Optional properties:
+
+- clocks: The phandle of the master clock to the CODEC
+- clock-names: Should be "mclk"
+
+- realtek,in1-differential
+- realtek,in3-differential
+  Boolean. Indicate MIC1/3 input are differential, rather than single-ended.
+
+- realtek,poweroff-in-suspend
+  Boolean. If the codec will be powered off in suspend, the resume should be
+  added delay time for waiting codec power ready.
+
+- realtek,dmic1-data-pin
+  0: dmic1 is not used
+  1: using GPIO2 pin as dmic1 data pin
+  2: using IN1P pin as dmic1 data pin
+
+Pins on the device (for linking into audio routes) for RT5660:
+
+  * DMIC L1
+  * DMIC R1
+  * IN1P
+  * IN1N
+  * IN2P
+  * IN3P
+  * IN3N
+  * SPO
+  * LOUTL
+  * LOUTR
+
+Example:
+
+rt5660 {
+	compatible = "realtek,rt5660";
+	reg = <0x1c>;
+};

Documentation/devicetree/bindings/sound/rt5663.txt

+RT5663/RT5668 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+- compatible : One of "realtek,rt5663" or "realtek,rt5668".
+
+- reg : The I2C address of the device.
+
+- interrupts : The CODEC's interrupt output.
+
+Optional properties:
+
+Pins on the device (for linking into audio routes) for RT5663/RT5668:
+
+  * IN1P
+  * IN1N
+  * IN2P
+  * IN2N
+  * HPOL
+  * HPOR
+
+Example:
+
+codec: rt5663@12 {
+	compatible = "realtek,rt5663";
+	reg = <0x12>;
+	interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+};

arch/arm/mach-s3c24xx/mach-mini2440.c

@@ -497,9 +497,28 @@ static struct i2c_board_info mini2440_i2c_devs[] __initdata = {
 	},
 };
 
+static struct uda134x_platform_data s3c24xx_uda134x = {
+	.l3 = {
+		.gpio_clk = S3C2410_GPB(4),
+		.gpio_data = S3C2410_GPB(3),
+		.gpio_mode = S3C2410_GPB(2),
+		.use_gpios = 1,
+		.data_hold = 1,
+		.data_setup = 1,
+		.clock_high = 1,
+		.mode_hold = 1,
+		.mode = 1,
+		.mode_setup = 1,
+	},
+	.model = UDA134X_UDA1341,
+};
+
 static struct platform_device uda1340_codec = {
 		.name = "uda134x-codec",
 		.id = -1,
+		.dev = {
+			.platform_data	= &s3c24xx_uda134x,
+		},
 };
 
 static struct platform_device *mini2440_devices[] __initdata = {

include/sound/l3.h

@@ -2,9 +2,15 @@
 #define _L3_H_ 1
 
 struct l3_pins {
-	void (*setdat)(int);
-	void (*setclk)(int);
-	void (*setmode)(int);
+	void (*setdat)(struct l3_pins *, int);
+	void (*setclk)(struct l3_pins *, int);
+	void (*setmode)(struct l3_pins *, int);
+
+	int gpio_data;
+	int gpio_clk;
+	int gpio_mode;
+	int use_gpios;
+
 	int data_hold;
 	int data_setup;
 	int clock_high;
@@ -13,6 +19,9 @@ struct l3_pins {
 	int mode_setup;
 };
 
+struct device;
+
 int l3_write(struct l3_pins *adap, u8 addr, u8 *data, int len);
+int l3_set_gpio_ops(struct device *dev, struct l3_pins *adap);
 
 #endif

include/sound/rt5660.h

+/*
+ * linux/sound/rt5660.h -- Platform data for RT5660
+ *
+ * Copyright 2016 Realtek Semiconductor Corp.
+ * Author: Oder Chiou <oder_chiou@realtek.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __LINUX_SND_RT5660_H
+#define __LINUX_SND_RT5660_H
+
+enum rt5660_dmic1_data_pin {
+	RT5660_DMIC1_NULL,
+	RT5660_DMIC1_DATA_GPIO2,
+	RT5660_DMIC1_DATA_IN1P,
+};
+
+struct rt5660_platform_data {
+	/* IN1 & IN3 can optionally be differential */
+	bool in1_diff;
+	bool in3_diff;
+	bool use_ldo2;
+	bool poweroff_codec_in_suspend;
+
+	enum rt5660_dmic1_data_pin dmic1_data_pin;
+};
+
+#endif

include/sound/s3c24xx_uda134x.h

@@ -7,7 +7,6 @@ struct s3c24xx_uda134x_platform_data {
 	int l3_clk;
 	int l3_mode;
 	int l3_data;
-	void (*power) (int);
 	int model;
 };
 

sound/soc/codecs/Kconfig

@@ -113,6 +113,8 @@ config SND_SOC_ALL_CODECS
 	select SND_SOC_RT5645 if I2C
 	select SND_SOC_RT5651 if I2C
 	select SND_SOC_RT5659 if I2C
+	select SND_SOC_RT5660 if I2C
+	select SND_SOC_RT5663 if I2C
 	select SND_SOC_RT5670 if I2C
 	select SND_SOC_RT5677 if I2C && SPI_MASTER
 	select SND_SOC_SGTL5000 if I2C
@@ -646,6 +648,8 @@ config SND_SOC_RL6231
 	default y if SND_SOC_RT5645=y
 	default y if SND_SOC_RT5651=y
 	default y if SND_SOC_RT5659=y
+	default y if SND_SOC_RT5660=y
+	default y if SND_SOC_RT5663=y
 	default y if SND_SOC_RT5670=y
 	default y if SND_SOC_RT5677=y
 	default m if SND_SOC_RT5514=m
@@ -654,6 +658,8 @@ config SND_SOC_RL6231
 	default m if SND_SOC_RT5645=m
 	default m if SND_SOC_RT5651=m
 	default m if SND_SOC_RT5659=m
+	default m if SND_SOC_RT5660=m
+	default m if SND_SOC_RT5663=m
 	default m if SND_SOC_RT5670=m
 	default m if SND_SOC_RT5677=m
 
@@ -666,6 +672,7 @@ config SND_SOC_RL6347A
 
 config SND_SOC_RT286
 	tristate
+	select SND_SOC_RT5663
 	depends on I2C
 
 config SND_SOC_RT298
@@ -698,6 +705,12 @@ config SND_SOC_RT5651
 config SND_SOC_RT5659
 	tristate
 
+config SND_SOC_RT5660
+	tristate
+
+config SND_SOC_RT5663
+	tristate
+
 config SND_SOC_RT5670
 	tristate
 

sound/soc/codecs/Makefile

@@ -113,6 +113,8 @@ snd-soc-rt5640-objs := rt5640.o
 snd-soc-rt5645-objs := rt5645.o
 snd-soc-rt5651-objs := rt5651.o
 snd-soc-rt5659-objs := rt5659.o
+snd-soc-rt5660-objs := rt5660.o
+snd-soc-rt5663-objs := rt5663.o
 snd-soc-rt5670-objs := rt5670.o
 snd-soc-rt5677-objs := rt5677.o
 snd-soc-rt5677-spi-objs := rt5677-spi.o
@@ -335,6 +337,8 @@ obj-$(CONFIG_SND_SOC_RT5640)	+= snd-soc-rt5640.o
 obj-$(CONFIG_SND_SOC_RT5645)	+= snd-soc-rt5645.o
 obj-$(CONFIG_SND_SOC_RT5651)	+= snd-soc-rt5651.o
 obj-$(CONFIG_SND_SOC_RT5659)	+= snd-soc-rt5659.o
+obj-$(CONFIG_SND_SOC_RT5660)	+= snd-soc-rt5660.o
+obj-$(CONFIG_SND_SOC_RT5663)	+= snd-soc-rt5663.o
 obj-$(CONFIG_SND_SOC_RT5670)	+= snd-soc-rt5670.o
 obj-$(CONFIG_SND_SOC_RT5677)	+= snd-soc-rt5677.o
 obj-$(CONFIG_SND_SOC_RT5677_SPI)	+= snd-soc-rt5677-spi.o

sound/soc/codecs/l3.c

@@ -20,6 +20,8 @@
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/gpio.h>
 
 #include <sound/l3.h>
 
@@ -32,11 +34,11 @@ static void sendbyte(struct l3_pins *adap, unsigned int byte)
 	int i;
 
 	for (i = 0; i < 8; i++) {
-		adap->setclk(0);
+		adap->setclk(adap, 0);
 		udelay(adap->data_hold);
-		adap->setdat(byte & 1);
+		adap->setdat(adap, byte & 1);
 		udelay(adap->data_setup);
-		adap->setclk(1);
+		adap->setclk(adap, 1);
 		udelay(adap->clock_high);
 		byte >>= 1;
 	}
@@ -55,10 +57,10 @@ static void sendbytes(struct l3_pins *adap, const u8 *buf,
 	for (i = 0; i < len; i++) {
 		if (i) {
 			udelay(adap->mode_hold);
-			adap->setmode(0);
+			adap->setmode(adap, 0);
 			udelay(adap->mode);
 		}
-		adap->setmode(1);
+		adap->setmode(adap, 1);
 		udelay(adap->mode_setup);
 		sendbyte(adap, buf[i]);
 	}
@@ -66,26 +68,71 @@ static void sendbytes(struct l3_pins *adap, const u8 *buf,
 
 int l3_write(struct l3_pins *adap, u8 addr, u8 *data, int len)
 {
-	adap->setclk(1);
-	adap->setdat(1);
-	adap->setmode(1);
+	adap->setclk(adap, 1);
+	adap->setdat(adap, 1);
+	adap->setmode(adap, 1);
 	udelay(adap->mode);
 
-	adap->setmode(0);
+	adap->setmode(adap, 0);
 	udelay(adap->mode_setup);
 	sendbyte(adap, addr);
 	udelay(adap->mode_hold);
 
 	sendbytes(adap, data, len);
 
-	adap->setclk(1);
-	adap->setdat(1);
-	adap->setmode(0);
+	adap->setclk(adap, 1);
+	adap->setdat(adap, 1);
+	adap->setmode(adap, 0);
 
 	return len;
 }
 EXPORT_SYMBOL_GPL(l3_write);
 
+
+static void l3_set_clk(struct l3_pins *adap, int val)
+{
+	gpio_set_value(adap->gpio_clk, val);
+}
+
+static void l3_set_data(struct l3_pins *adap, int val)
+{
+	gpio_set_value(adap->gpio_data, val);
+}
+
+static void l3_set_mode(struct l3_pins *adap, int val)
+{
+	gpio_set_value(adap->gpio_mode, val);
+}
+
+int l3_set_gpio_ops(struct device *dev, struct l3_pins *adap)
+{
+	int ret;
+
+	if (!adap->use_gpios)
+		return -EINVAL;
+
+	ret = devm_gpio_request_one(dev, adap->gpio_data,
+				GPIOF_OUT_INIT_LOW, "l3_data");
+	if (ret < 0)
+		return ret;
+	adap->setdat = l3_set_data;
+
+	ret = devm_gpio_request_one(dev, adap->gpio_clk,
+				GPIOF_OUT_INIT_LOW, "l3_clk");
+	if (ret < 0)
+		return ret;
+	adap->setclk = l3_set_clk;
+
+	ret = devm_gpio_request_one(dev, adap->gpio_mode,
+				GPIOF_OUT_INIT_LOW, "l3_mode");
+	if (ret < 0)
+		return ret;
+	adap->setmode = l3_set_mode;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(l3_set_gpio_ops);
+
 MODULE_DESCRIPTION("L3 bit-banging driver");
 MODULE_AUTHOR("Christian Pellegrin <chripell@evolware.org>");
 MODULE_LICENSE("GPL");

sound/soc/codecs/rt5659.c

@@ -9,6 +9,7 @@
  * published by the Free Software Foundation.
  */
 
+#include <linux/clk.h>
 #include <linux/module.h>
 #include <linux/moduleparam.h>
 #include <linux/init.h>
@@ -3565,7 +3566,9 @@ static int rt5659_set_bclk_ratio(struct snd_soc_dai *dai, unsigned int ratio)
 static int rt5659_set_bias_level(struct snd_soc_codec *codec,
 			enum snd_soc_bias_level level)
 {
+	struct snd_soc_dapm_context *dapm = snd_soc_codec_get_dapm(codec);
 	struct rt5659_priv *rt5659 = snd_soc_codec_get_drvdata(codec);
+	int ret;
 
 	switch (level) {
 	case SND_SOC_BIAS_PREPARE:
@@ -3582,6 +3585,17 @@ static int rt5659_set_bias_level(struct snd_soc_codec *codec,
 			RT5659_PWR_FV1 | RT5659_PWR_FV2);
 		break;
 
+	case SND_SOC_BIAS_STANDBY:
+		if (dapm->bias_level == SND_SOC_BIAS_OFF) {
+			ret = clk_prepare_enable(rt5659->mclk);
+			if (ret) {
+				dev_err(codec->dev,
+					"failed to enable MCLK: %d\n", ret);
+				return ret;
+			}
+		}
+		break;
+
 	case SND_SOC_BIAS_OFF:
 		regmap_update_bits(rt5659->regmap, RT5659_PWR_DIG_1,
 			RT5659_PWR_LDO, 0);
@@ -3591,6 +3605,7 @@ static int rt5659_set_bias_level(struct snd_soc_codec *codec,
 			RT5659_PWR_MB | RT5659_PWR_VREF2);
 		regmap_update_bits(rt5659->regmap, RT5659_DIG_MISC,
 			RT5659_DIG_GATE_CTRL, 0);
+		clk_disable_unprepare(rt5659->mclk);
 		break;
 
 	default:
@@ -4022,6 +4037,15 @@ static int rt5659_i2c_probe(struct i2c_client *i2c,
 
 	regmap_write(rt5659->regmap, RT5659_RESET, 0);
 
+	/* Check if MCLK provided */
+	rt5659->mclk = devm_clk_get(&i2c->dev, "mclk");
+	if (IS_ERR(rt5659->mclk)) {
+		if (PTR_ERR(rt5659->mclk) != -ENOENT)
+			return PTR_ERR(rt5659->mclk);
+		/* Otherwise mark the mclk pointer to NULL */
+		rt5659->mclk = NULL;
+	}
+
 	rt5659_calibrate(rt5659);
 
 	/* line in diff mode*/
@@ -4165,6 +4189,9 @@ static int rt5659_i2c_probe(struct i2c_client *i2c,
 		if (ret)
 			dev_err(&i2c->dev, "Failed to reguest IRQ: %d\n", ret);
 
+		/* Enable IRQ output for GPIO1 pin any way */
+		regmap_update_bits(rt5659->regmap, RT5659_GPIO_CTRL_1,
+				   RT5659_GP1_PIN_MASK, RT5659_GP1_PIN_IRQ);
 	}
 
 	return snd_soc_register_codec(&i2c->dev, &soc_codec_dev_rt5659,

sound/soc/codecs/rt5659.h

@@ -180,9 +180,9 @@
 #define RT5659_IRQ_CTRL_1			0x00b6
 #define RT5659_IRQ_CTRL_2			0x00b7
 #define RT5659_IRQ_CTRL_3			0x00b8
-#define RT5659_IRQ_CTRL_4			0x00b9
-#define RT5659_IRQ_CTRL_5			0x00ba
-#define RT5659_IRQ_CTRL_6			0x00bb
+#define RT5659_IRQ_CTRL_4			0x00ba
+#define RT5659_IRQ_CTRL_5			0x00bb
+#define RT5659_IRQ_CTRL_6			0x00bc
 #define RT5659_INT_ST_1				0x00be
 #define RT5659_INT_ST_2				0x00bf
 #define RT5659_GPIO_CTRL_1			0x00c0
@@ -1796,6 +1796,7 @@ struct rt5659_priv {
 	struct gpio_desc *gpiod_reset;
 	struct snd_soc_jack *hs_jack;
 	struct delayed_work jack_detect_work;
+	struct clk *mclk;
 
 	int sysclk;
 	int sysclk_src;

sound/soc/codecs/rt5677.c

@@ -9,6 +9,7 @@
  * published by the Free Software Foundation.
  */
 
+#include <linux/acpi.h>
 #include <linux/fs.h>
 #include <linux/module.h>
 #include <linux/moduleparam.h>
@@ -40,6 +41,15 @@
 
 #define RT5677_PR_BASE (RT5677_PR_RANGE_BASE + (0 * RT5677_PR_SPACING))
 
+/* GPIO indexes defined by ACPI */
+enum {
+	RT5677_GPIO_PLUG_DET		= 0,
+	RT5677_GPIO_MIC_PRESENT_L	= 1,
+	RT5677_GPIO_HOTWORD_DET_L	= 2,
+	RT5677_GPIO_DSP_INT		= 3,
+	RT5677_GPIO_HP_AMP_SHDN_L	= 4,
+};
+
 static const struct regmap_range_cfg rt5677_ranges[] = {
 	{
 		.name = "PR",
@@ -5020,10 +5030,47 @@ static const struct regmap_config rt5677_regmap = {
 static const struct i2c_device_id rt5677_i2c_id[] = {
 	{ "rt5677", RT5677 },
 	{ "rt5676", RT5676 },
+	{ "RT5677CE:00", RT5677 },
 	{ }
 };
 MODULE_DEVICE_TABLE(i2c, rt5677_i2c_id);
 
+static const struct acpi_gpio_params plug_det_gpio = { RT5677_GPIO_PLUG_DET, 0, false };
+static const struct acpi_gpio_params mic_present_gpio = { RT5677_GPIO_MIC_PRESENT_L, 0, false };
+static const struct acpi_gpio_params headphone_enable_gpio = { RT5677_GPIO_HP_AMP_SHDN_L, 0, false };
+
+static const struct acpi_gpio_mapping bdw_rt5677_gpios[] = {
+	{ "plug-det-gpios", &plug_det_gpio, 1 },
+	{ "mic-present-gpios", &mic_present_gpio, 1 },
+	{ "headphone-enable-gpios", &headphone_enable_gpio, 1 },
+	{ NULL },
+};
+
+static void rt5677_read_acpi_properties(struct rt5677_priv *rt5677,
+		struct device *dev)
+{
+	int ret;
+	u32 val;
+
+	ret = acpi_dev_add_driver_gpios(ACPI_COMPANION(dev),
+			bdw_rt5677_gpios);
+	if (ret)
+		dev_warn(dev, "Failed to add driver gpios\n");
+
+	if (!device_property_read_u32(dev, "DCLK", &val))
+		rt5677->pdata.dmic2_clk_pin = val;
+
+	rt5677->pdata.in1_diff = device_property_read_bool(dev, "IN1");
+	rt5677->pdata.in2_diff = device_property_read_bool(dev, "IN2");
+	rt5677->pdata.lout1_diff = device_property_read_bool(dev, "OUT1");
+	rt5677->pdata.lout2_diff = device_property_read_bool(dev, "OUT2");
+	rt5677->pdata.lout3_diff = device_property_read_bool(dev, "OUT3");
+
+	device_property_read_u32(dev, "JD1", &rt5677->pdata.jd1_gpio);
+	device_property_read_u32(dev, "JD2", &rt5677->pdata.jd2_gpio);
+	device_property_read_u32(dev, "JD3", &rt5677->pdata.jd3_gpio);
+}
+
 static void rt5677_read_device_properties(struct rt5677_priv *rt5677,
 		struct device *dev)
 {
@@ -5129,8 +5176,12 @@ static int rt5677_i2c_probe(struct i2c_client *i2c,
 
 	if (pdata)
 		rt5677->pdata = *pdata;
-	else
+	else if (i2c->dev.of_node)
 		rt5677_read_device_properties(rt5677, &i2c->dev);
+	else if (ACPI_HANDLE(&i2c->dev))
+		rt5677_read_acpi_properties(rt5677, &i2c->dev);
+	else
+		return -EINVAL;
 
 	/* pow-ldo2 and reset are optional. The codec pins may be statically
 	 * connected on the board without gpios. If the gpio device property

sound/soc/codecs/uda134x.c

@@ -546,6 +546,7 @@ static int uda134x_codec_probe(struct platform_device *pdev)
 {
 	struct uda134x_platform_data *pd = pdev->dev.platform_data;
 	struct uda134x_priv *uda134x;
+	int ret;
 
 	if (!pd) {
 		dev_err(&pdev->dev, "Missing L3 bitbang function\n");
@@ -559,6 +560,12 @@ static int uda134x_codec_probe(struct platform_device *pdev)
 	uda134x->pd = pd;
 	platform_set_drvdata(pdev, uda134x);
 
+	if (pd->l3.use_gpios) {
+		ret = l3_set_gpio_ops(&pdev->dev, &uda134x->pd->l3);
+		if (ret < 0)
+			return ret;
+	}
+
 	uda134x->regmap = devm_regmap_init(&pdev->dev, NULL, pd,
 		&uda134x_regmap_config);
 	if (IS_ERR(uda134x->regmap))

sound/soc/samsung/Kconfig

-config SND_SOC_SAMSUNG
+menuconfig SND_SOC_SAMSUNG
 	tristate "ASoC support for Samsung"
 	depends on (PLAT_SAMSUNG || ARCH_EXYNOS)
 	select SND_SOC_GENERIC_DMAENGINE_PCM
-	help
+	---help---
 	  Say Y or M if you want to add support for codecs attached to
 	  the Samsung SoCs' Audio interfaces. You will also need to
 	  select the audio interfaces to support below.
 
+if SND_SOC_SAMSUNG
+
 config SND_S3C24XX_I2S
 	tristate
 
@@ -18,22 +20,22 @@ config SND_S3C2412_SOC_I2S
 	select SND_S3C_I2SV2_SOC
 
 config SND_SAMSUNG_PCM
-	tristate
+	tristate "Samsung PCM interface support"
 
 config SND_SAMSUNG_AC97
 	tristate
 	select SND_SOC_AC97_BUS
 
 config SND_SAMSUNG_SPDIF
-	tristate
+	tristate "Samsung SPDIF transmitter support"
 	select SND_SOC_SPDIF
 
 config SND_SAMSUNG_I2S
-	tristate
+	tristate "Samsung I2S interface support"
 
 config SND_SOC_SAMSUNG_NEO1973_WM8753
 	tristate "Audio support for Openmoko Neo1973 Smartphones (GTA02)"
-	depends on SND_SOC_SAMSUNG && MACH_NEO1973_GTA02
+	depends on MACH_NEO1973_GTA02
 	select SND_S3C24XX_I2S
 	select SND_SOC_WM8753
 	select SND_SOC_BT_SCO
@@ -43,7 +45,7 @@ config SND_SOC_SAMSUNG_NEO1973_WM8753
 
 config SND_SOC_SAMSUNG_JIVE_WM8750
 	tristate "SoC I2S Audio support for Jive"
-	depends on SND_SOC_SAMSUNG && MACH_JIVE && I2C
+	depends on MACH_JIVE && I2C
 	select SND_SOC_WM8750
 	select SND_S3C2412_SOC_I2S
 	help
@@ -51,7 +53,7 @@ config SND_SOC_SAMSUNG_JIVE_WM8750
 
 config SND_SOC_SAMSUNG_SMDK_WM8580
 	tristate "SoC I2S Audio support for WM8580 on SMDK"
-	depends on SND_SOC_SAMSUNG && (MACH_SMDK6410 || MACH_SMDKC100 || MACH_SMDKV210 || MACH_SMDKC110)
+	depends on MACH_SMDK6410 || MACH_SMDKC100 || MACH_SMDKV210 || MACH_SMDKC110
 	depends on I2C
 	select SND_SOC_WM8580
 	select SND_SAMSUNG_I2S
@@ -60,7 +62,6 @@ config SND_SOC_SAMSUNG_SMDK_WM8580
 
 config SND_SOC_SAMSUNG_SMDK_WM8994
 	tristate "SoC I2S Audio support for WM8994 on SMDK"
-	depends on SND_SOC_SAMSUNG
 	depends on I2C=y
 	select MFD_WM8994
 	select SND_SOC_WM8994
@@ -70,7 +71,7 @@ config SND_SOC_SAMSUNG_SMDK_WM8994
 
 config SND_SOC_SAMSUNG_SMDK2443_WM9710
 	tristate "SoC AC97 Audio support for SMDK2443 - WM9710"
-	depends on SND_SOC_SAMSUNG && MACH_SMDK2443
+	depends on MACH_SMDK2443
 	select AC97_BUS
 	select SND_SOC_AC97_CODEC
 	select SND_SAMSUNG_AC97
@@ -80,7 +81,7 @@ config SND_SOC_SAMSUNG_SMDK2443_WM9710
 
 config SND_SOC_SAMSUNG_LN2440SBC_ALC650
 	tristate "SoC AC97 Audio support for LN2440SBC - ALC650"
-	depends on SND_SOC_SAMSUNG && ARCH_S3C24XX
+	depends on ARCH_S3C24XX
 	select AC97_BUS
 	select SND_SOC_AC97_CODEC
 	select SND_SAMSUNG_AC97
@@ -90,7 +91,7 @@ config SND_SOC_SAMSUNG_LN2440SBC_ALC650
 
 config SND_SOC_SAMSUNG_S3C24XX_UDA134X
 	tristate "SoC I2S Audio support UDA134X wired to a S3C24XX"
-	depends on SND_SOC_SAMSUNG && ARCH_S3C24XX
+	depends on ARCH_S3C24XX
 	select SND_S3C24XX_I2S
 	select SND_SOC_L3
 	select SND_SOC_UDA134X
@@ -102,21 +103,21 @@ config SND_SOC_SAMSUNG_SIMTEC
 
 config SND_SOC_SAMSUNG_SIMTEC_TLV320AIC23
 	tristate "SoC I2S Audio support for TLV320AIC23 on Simtec boards"
-	depends on SND_SOC_SAMSUNG && ARCH_S3C24XX && I2C
+	depends on ARCH_S3C24XX && I2C
 	select SND_S3C24XX_I2S
 	select SND_SOC_TLV320AIC23_I2C
 	select SND_SOC_SAMSUNG_SIMTEC
 
 config SND_SOC_SAMSUNG_SIMTEC_HERMES
 	tristate "SoC I2S Audio support for Simtec Hermes board"
-	depends on SND_SOC_SAMSUNG && ARCH_S3C24XX && I2C
+	depends on ARCH_S3C24XX && I2C
 	select SND_S3C24XX_I2S
 	select SND_SOC_TLV320AIC3X
 	select SND_SOC_SAMSUNG_SIMTEC
 
 config SND_SOC_SAMSUNG_H1940_UDA1380
 	tristate "Audio support for the HP iPAQ H1940"
-	depends on SND_SOC_SAMSUNG && ARCH_H1940 && I2C
+	depends on ARCH_H1940 && I2C
 	select SND_S3C24XX_I2S
 	select SND_SOC_UDA1380
 	help
@@ -124,7 +125,7 @@ config SND_SOC_SAMSUNG_H1940_UDA1380
 
 config SND_SOC_SAMSUNG_RX1950_UDA1380
 	tristate "Audio support for the HP iPAQ RX1950"
-	depends on SND_SOC_SAMSUNG && MACH_RX1950 && I2C
+	depends on MACH_RX1950 && I2C
 	select SND_S3C24XX_I2S
 	select SND_SOC_UDA1380
 	help
@@ -132,7 +133,7 @@ config SND_SOC_SAMSUNG_RX1950_UDA1380
 
 config SND_SOC_SAMSUNG_SMDK_WM9713
 	tristate "SoC AC97 Audio support for SMDK with WM9713"
-	depends on SND_SOC_SAMSUNG && (MACH_SMDK6410 || MACH_SMDKC100 || MACH_SMDKV210 || MACH_SMDKC110)
+	depends on MACH_SMDK6410 || MACH_SMDKC100 || MACH_SMDKV210 || MACH_SMDKC110
 	select SND_SOC_WM9713
 	select SND_SAMSUNG_AC97
 	help
@@ -140,20 +141,19 @@ config SND_SOC_SAMSUNG_SMDK_WM9713
 
 config SND_SOC_SMARTQ
 	tristate "SoC I2S Audio support for SmartQ board"
-	depends on SND_SOC_SAMSUNG && MACH_SMARTQ && I2C
+	depends on MACH_SMARTQ && I2C
 	select SND_SAMSUNG_I2S
 	select SND_SOC_WM8750
 
 config SND_SOC_SAMSUNG_SMDK_SPDIF
 	tristate "SoC S/PDIF Audio support for SMDK"
-	depends on SND_SOC_SAMSUNG
 	select SND_SAMSUNG_SPDIF
 	help
 	  Say Y if you want to add support for SoC S/PDIF audio on the SMDK.
 
 config SND_SOC_SMDK_WM8580_PCM
 	tristate "SoC PCM Audio support for WM8580 on SMDK"
-	depends on SND_SOC_SAMSUNG && (MACH_SMDKV210 || MACH_SMDKC110)
+	depends on MACH_SMDKV210 || MACH_SMDKC110
 	depends on I2C
 	select SND_SOC_WM8580
 	select SND_SAMSUNG_PCM
@@ -162,7 +162,6 @@ config SND_SOC_SMDK_WM8580_PCM
 
 config SND_SOC_SMDK_WM8994_PCM
 	tristate "SoC PCM Audio support for WM8994 on SMDK"
-	depends on SND_SOC_SAMSUNG
 	depends on I2C=y
 	select MFD_WM8994
 	select SND_SOC_WM8994
@@ -172,7 +171,7 @@ config SND_SOC_SMDK_WM8994_PCM
 
 config SND_SOC_SPEYSIDE
 	tristate "Audio support for Wolfson Speyside"
-	depends on SND_SOC_SAMSUNG && I2C && SPI_MASTER
+	depends on I2C && SPI_MASTER
 	depends on MACH_WLF_CRAGG_6410 || COMPILE_TEST
 	select SND_SAMSUNG_I2S
 	select SND_SOC_WM8996
@@ -182,14 +181,14 @@ config SND_SOC_SPEYSIDE
 
 config SND_SOC_TOBERMORY
 	tristate "Audio support for Wolfson Tobermory"
-	depends on SND_SOC_SAMSUNG && INPUT && I2C
+	depends on INPUT && I2C
 	depends on MACH_WLF_CRAGG_6410 || COMPILE_TEST
 	select SND_SAMSUNG_I2S
 	select SND_SOC_WM8962
 
 config SND_SOC_BELLS
 	tristate "Audio support for Wolfson Bells"
-	depends on SND_SOC_SAMSUNG && MFD_ARIZONA && I2C && SPI_MASTER
+	depends on MFD_ARIZONA && I2C && SPI_MASTER
 	depends on MACH_WLF_CRAGG_6410 || COMPILE_TEST
 	select SND_SAMSUNG_I2S
 	select SND_SOC_WM5102
@@ -200,7 +199,7 @@ config SND_SOC_BELLS
 
 config SND_SOC_LOWLAND
 	tristate "Audio support for Wolfson Lowland"
-	depends on SND_SOC_SAMSUNG && I2C
+	depends on I2C
 	depends on MACH_WLF_CRAGG_6410 || COMPILE_TEST
 	select SND_SAMSUNG_I2S
 	select SND_SOC_WM5100
@@ -208,7 +207,7 @@ config SND_SOC_LOWLAND
 
 config SND_SOC_LITTLEMILL
 	tristate "Audio support for Wolfson Littlemill"
-	depends on SND_SOC_SAMSUNG && I2C
+	depends on I2C
 	depends on MACH_WLF_CRAGG_6410 || COMPILE_TEST
 	select SND_SAMSUNG_I2S
 	select MFD_WM8994
@@ -216,7 +215,7 @@ config SND_SOC_LITTLEMILL
 
 config SND_SOC_SNOW
 	tristate "Audio support for Google Snow boards"
-	depends on SND_SOC_SAMSUNG && I2C
+	depends on I2C
 	select SND_SOC_MAX98090
 	select SND_SOC_MAX98095
 	select SND_SAMSUNG_I2S
@@ -226,6 +225,8 @@ config SND_SOC_SNOW
 
 config SND_SOC_ARNDALE_RT5631_ALC5631
         tristate "Audio support for RT5631(ALC5631) on Arndale Board"
-        depends on SND_SOC_SAMSUNG && I2C
+        depends on I2C
         select SND_SAMSUNG_I2S
         select SND_SOC_RT5631
+
+endif #SND_SOC_SAMSUNG

sound/soc/samsung/ac97.c

@@ -38,16 +38,16 @@ struct s3c_ac97_info {
 };
 static struct s3c_ac97_info s3c_ac97;
 
-static struct s3c_dma_params s3c_ac97_pcm_out = {
-	.dma_size	= 4,
+static struct snd_dmaengine_dai_dma_data s3c_ac97_pcm_out = {
+	.addr_width	= 4,
 };
 
-static struct s3c_dma_params s3c_ac97_pcm_in = {
-	.dma_size	= 4,
+static struct snd_dmaengine_dai_dma_data s3c_ac97_pcm_in = {
+	.addr_width	= 4,
 };
 
-static struct s3c_dma_params s3c_ac97_mic_in = {
-	.dma_size	= 4,
+static struct snd_dmaengine_dai_dma_data s3c_ac97_mic_in = {
+	.addr_width	= 4,
 };
 
 static void s3c_ac97_activate(struct snd_ac97 *ac97)
@@ -74,7 +74,7 @@ static void s3c_ac97_activate(struct snd_ac97 *ac97)
 	writel(ac_glbctrl, s3c_ac97.regs + S3C_AC97_GLBCTRL);
 
 	if (!wait_for_completion_timeout(&s3c_ac97.done, HZ))
-		pr_err("AC97: Unable to activate!");
+		pr_err("AC97: Unable to activate!\n");
 }
 
 static unsigned short s3c_ac97_read(struct snd_ac97 *ac97,
@@ -100,7 +100,7 @@ static unsigned short s3c_ac97_read(struct snd_ac97 *ac97,
 	writel(ac_glbctrl, s3c_ac97.regs + S3C_AC97_GLBCTRL);
 
 	if (!wait_for_completion_timeout(&s3c_ac97.done, HZ))
-		pr_err("AC97: Unable to read!");
+		pr_err("AC97: Unable to read!\n");
 
 	stat = readl(s3c_ac97.regs + S3C_AC97_STAT);
 	addr = (stat >> 16) & 0x7f;
@@ -137,7 +137,7 @@ static void s3c_ac97_write(struct snd_ac97 *ac97, unsigned short reg,
 	writel(ac_glbctrl, s3c_ac97.regs + S3C_AC97_GLBCTRL);
 
 	if (!wait_for_completion_timeout(&s3c_ac97.done, HZ))
-		pr_err("AC97: Unable to write!");
+		pr_err("AC97: Unable to write!\n");
 
 	ac_codec_cmd = readl(s3c_ac97.regs + S3C_AC97_CODEC_CMD);
 	ac_codec_cmd |= S3C_AC97_CODEC_CMD_READ;
@@ -273,14 +273,14 @@ static const struct snd_soc_dai_ops s3c_ac97_mic_dai_ops = {
 
 static int s3c_ac97_dai_probe(struct snd_soc_dai *dai)
 {
-	samsung_asoc_init_dma_data(dai, &s3c_ac97_pcm_out, &s3c_ac97_pcm_in);
+	snd_soc_dai_init_dma_data(dai, &s3c_ac97_pcm_out, &s3c_ac97_pcm_in);
 
 	return 0;
 }
 
 static int s3c_ac97_mic_dai_probe(struct snd_soc_dai *dai)
 {
-	samsung_asoc_init_dma_data(dai, NULL, &s3c_ac97_mic_in);
+	snd_soc_dai_init_dma_data(dai, NULL, &s3c_ac97_mic_in);
 
 	return 0;
 }
@@ -346,12 +346,12 @@ static int s3c_ac97_probe(struct platform_device *pdev)
 	if (IS_ERR(s3c_ac97.regs))
 		return PTR_ERR(s3c_ac97.regs);
 
-	s3c_ac97_pcm_out.slave = ac97_pdata->dma_playback;
-	s3c_ac97_pcm_out.dma_addr = mem_res->start + S3C_AC97_PCM_DATA;
-	s3c_ac97_pcm_in.slave = ac97_pdata->dma_capture;
-	s3c_ac97_pcm_in.dma_addr = mem_res->start + S3C_AC97_PCM_DATA;
-	s3c_ac97_mic_in.slave = ac97_pdata->dma_capture_mic;
-	s3c_ac97_mic_in.dma_addr = mem_res->start + S3C_AC97_MIC_DATA;
+	s3c_ac97_pcm_out.filter_data = ac97_pdata->dma_playback;
+	s3c_ac97_pcm_out.addr = mem_res->start + S3C_AC97_PCM_DATA;
+	s3c_ac97_pcm_in.filter_data = ac97_pdata->dma_capture;
+	s3c_ac97_pcm_in.addr = mem_res->start + S3C_AC97_PCM_DATA;
+	s3c_ac97_mic_in.filter_data = ac97_pdata->dma_capture_mic;
+	s3c_ac97_mic_in.addr = mem_res->start + S3C_AC97_MIC_DATA;
 
 	init_completion(&s3c_ac97.done);
 	mutex_init(&s3c_ac97.lock);

sound/soc/samsung/dma.h

 /*
- *  dma.h --
- *
  *  This program is free software; you can redistribute  it and/or modify it
  *  under  the terms of  the GNU General  Public License as published by the
  *  Free Software Foundation;  either version 2 of the  License, or (at your
@@ -9,27 +7,15 @@
  *  ALSA PCM interface for the Samsung SoC
  */
 
-#ifndef _S3C_AUDIO_H
-#define _S3C_AUDIO_H
+#ifndef _SAMSUNG_DMA_H
+#define _SAMSUNG_DMA_H
 
 #include <sound/dmaengine_pcm.h>
-#include <linux/dmaengine.h>
-
-struct s3c_dma_params {
-	void *slave;				/* Channel ID */
-	dma_addr_t dma_addr;
-	int dma_size;			/* Size of the DMA transfer */
-	char *ch_name;
-	struct snd_dmaengine_dai_dma_data dma_data;
-};
 
-void samsung_asoc_init_dma_data(struct snd_soc_dai *dai,
-				struct s3c_dma_params *playback,
-				struct s3c_dma_params *capture);
 /*
  * @tx, @rx arguments can be NULL if the DMA channel names are "tx", "rx",
  * otherwise actual DMA channel names must be passed to this function.
  */
 int samsung_asoc_dma_platform_register(struct device *dev, dma_filter_fn filter,
 				       const char *tx, const char *rx);
-#endif
+#endif /* _SAMSUNG_DMA_H */

sound/soc/samsung/dmaengine.c

@@ -16,49 +16,18 @@
  */
 
 #include <linux/module.h>
-#include <linux/amba/pl08x.h>
-#include <linux/platform_data/dma-s3c24xx.h>
-
 #include <sound/core.h>
 #include <sound/pcm.h>
 #include <sound/pcm_params.h>
 #include <sound/dmaengine_pcm.h>
 #include <sound/soc.h>
-#include <sound/soc-dai.h>
 
 #include "dma.h"
 
-void samsung_asoc_init_dma_data(struct snd_soc_dai *dai,
-				struct s3c_dma_params *playback,
-				struct s3c_dma_params *capture)
-{
-	struct snd_dmaengine_dai_dma_data *playback_data = NULL;
-	struct snd_dmaengine_dai_dma_data *capture_data = NULL;
-
-	if (playback) {
-		playback_data = &playback->dma_data;
-		playback_data->filter_data = playback->slave;
-		playback_data->chan_name = playback->ch_name;
-		playback_data->addr = playback->dma_addr;
-		playback_data->addr_width = playback->dma_size;
-	}
-	if (capture) {
-		capture_data = &capture->dma_data;
-		capture_data->filter_data = capture->slave;
-		capture_data->chan_name = capture->ch_name;
-		capture_data->addr = capture->dma_addr;
-		capture_data->addr_width = capture->dma_size;
-	}
-
-	snd_soc_dai_init_dma_data(dai, playback_data, capture_data);
-}
-EXPORT_SYMBOL_GPL(samsung_asoc_init_dma_data);
-
 int samsung_asoc_dma_platform_register(struct device *dev, dma_filter_fn filter,
 				       const char *tx, const char *rx)
 {
 	unsigned int flags = SND_DMAENGINE_PCM_FLAG_COMPAT;
-
 	struct snd_dmaengine_pcm_config *pcm_conf;
 
 	pcm_conf = devm_kzalloc(dev, sizeof(*pcm_conf), GFP_KERNEL);

sound/soc/samsung/i2s.c

@@ -87,9 +87,9 @@ struct i2s_dai {
 	/* Driver for this DAI */
 	struct snd_soc_dai_driver i2s_dai_drv;
 	/* DMA parameters */
-	struct s3c_dma_params dma_playback;
-	struct s3c_dma_params dma_capture;
-	struct s3c_dma_params idma_playback;
+	struct snd_dmaengine_dai_dma_data dma_playback;
+	struct snd_dmaengine_dai_dma_data dma_capture;
+	struct snd_dmaengine_dai_dma_data idma_playback;
 	dma_filter_fn filter;
 	u32	quirks;
 	u32	suspend_i2smod;
@@ -692,15 +692,15 @@ static int i2s_hw_params(struct snd_pcm_substream *substream,
 		break;
 	case 2:
 		if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
-			i2s->dma_playback.dma_size = 4;
+			i2s->dma_playback.addr_width = 4;
 		else
-			i2s->dma_capture.dma_size = 4;
+			i2s->dma_capture.addr_width = 4;
 		break;
 	case 1:
 		if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
-			i2s->dma_playback.dma_size = 2;
+			i2s->dma_playback.addr_width = 2;
 		else
-			i2s->dma_capture.dma_size = 2;
+			i2s->dma_capture.addr_width = 2;
 
 		break;
 	default:
@@ -754,7 +754,7 @@ static int i2s_hw_params(struct snd_pcm_substream *substream,
 	writel(mod, i2s->addr + I2SMOD);
 	spin_unlock_irqrestore(i2s->lock, flags);
 
-	samsung_asoc_init_dma_data(dai, &i2s->dma_playback, &i2s->dma_capture);
+	snd_soc_dai_init_dma_data(dai, &i2s->dma_playback, &i2s->dma_capture);
 
 	i2s->frmclk = params_rate(params);
 
@@ -991,10 +991,10 @@ static int samsung_i2s_dai_probe(struct snd_soc_dai *dai)
 	unsigned long flags;
 
 	if (is_secondary(i2s)) { /* If this is probe on the secondary DAI */
-		samsung_asoc_init_dma_data(dai, &other->sec_dai->dma_playback,
+		snd_soc_dai_init_dma_data(dai, &other->sec_dai->dma_playback,
 					   NULL);
 	} else {
-		samsung_asoc_init_dma_data(dai, &i2s->dma_playback,
+		snd_soc_dai_init_dma_data(dai, &i2s->dma_playback,
 					   &i2s->dma_capture);
 
 		if (i2s->quirks & QUIRK_NEED_RSTCLR)
@@ -1002,7 +1002,7 @@ static int samsung_i2s_dai_probe(struct snd_soc_dai *dai)
 
 		if (i2s->quirks & QUIRK_SUPPORTS_IDMA)
 			idma_reg_addr_init(i2s->addr,
-					i2s->sec_dai->idma_playback.dma_addr);
+					i2s->sec_dai->idma_playback.addr);
 	}
 
 	/* Reset any constraint on RFS and BFS */
@@ -1262,8 +1262,8 @@ static int samsung_i2s_probe(struct platform_device *pdev)
 			return -EINVAL;
 		}
 
-		pri_dai->dma_playback.slave = i2s_pdata->dma_playback;
-		pri_dai->dma_capture.slave = i2s_pdata->dma_capture;
+		pri_dai->dma_playback.filter_data = i2s_pdata->dma_playback;
+		pri_dai->dma_capture.filter_data = i2s_pdata->dma_capture;
 		pri_dai->filter = i2s_pdata->dma_filter;
 
 		if (&i2s_pdata->type)
@@ -1302,12 +1302,12 @@ static int samsung_i2s_probe(struct platform_device *pdev)
 		dev_err(&pdev->dev, "failed to enable clock: %d\n", ret);
 		return ret;
 	}
-	pri_dai->dma_playback.dma_addr = regs_base + I2STXD;
-	pri_dai->dma_capture.dma_addr = regs_base + I2SRXD;
-	pri_dai->dma_playback.ch_name = "tx";
-	pri_dai->dma_capture.ch_name = "rx";
-	pri_dai->dma_playback.dma_size = 4;
-	pri_dai->dma_capture.dma_size = 4;
+	pri_dai->dma_playback.addr = regs_base + I2STXD;
+	pri_dai->dma_capture.addr = regs_base + I2SRXD;
+	pri_dai->dma_playback.chan_name = "tx";
+	pri_dai->dma_capture.chan_name = "rx";
+	pri_dai->dma_playback.addr_width = 4;
+	pri_dai->dma_capture.addr_width = 4;
 	pri_dai->quirks = quirks;
 	pri_dai->variant_regs = i2s_dai_data->i2s_variant_regs;
 
@@ -1318,31 +1318,33 @@ static int samsung_i2s_probe(struct platform_device *pdev)
 		sec_dai = i2s_alloc_dai(pdev, true);
 		if (!sec_dai) {
 			dev_err(&pdev->dev, "Unable to alloc I2S_sec\n");
-			return -ENOMEM;
+			ret = -ENOMEM;
+			goto err_disable_clk;
 		}
 
 		sec_dai->lock = &pri_dai->spinlock;
 		sec_dai->variant_regs = pri_dai->variant_regs;
-		sec_dai->dma_playback.dma_addr = regs_base + I2STXDS;
-		sec_dai->dma_playback.ch_name = "tx-sec";
+		sec_dai->dma_playback.addr = regs_base + I2STXDS;
+		sec_dai->dma_playback.chan_name = "tx-sec";
 
 		if (!np) {
-			sec_dai->dma_playback.slave = i2s_pdata->dma_play_sec;
+			sec_dai->dma_playback.filter_data = i2s_pdata->dma_play_sec;
 			sec_dai->filter = i2s_pdata->dma_filter;
 		}
 
-		sec_dai->dma_playback.dma_size = 4;
+		sec_dai->dma_playback.addr_width = 4;
 		sec_dai->addr = pri_dai->addr;
 		sec_dai->clk = pri_dai->clk;
 		sec_dai->quirks = quirks;
-		sec_dai->idma_playback.dma_addr = idma_addr;
+		sec_dai->idma_playback.addr = idma_addr;
 		sec_dai->pri_dai = pri_dai;
 		pri_dai->sec_dai = sec_dai;
 	}
 
 	if (i2s_pdata && i2s_pdata->cfg_gpio && i2s_pdata->cfg_gpio(pdev)) {
 		dev_err(&pdev->dev, "Unable to configure gpio\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto err_disable_clk;
 	}
 
 	ret = devm_snd_soc_register_component(&pri_dai->pdev->dev,
@@ -1366,6 +1368,8 @@ static int samsung_i2s_probe(struct platform_device *pdev)
 err_free_dai:
 	if (sec_dai)
 		i2s_free_sec_dai(sec_dai);
+err_disable_clk:
+	clk_disable_unprepare(pri_dai->clk);
 	return ret;
 }
 

sound/soc/samsung/idma.c

@@ -22,7 +22,6 @@
 
 #include "i2s.h"
 #include "idma.h"
-#include "dma.h"
 #include "i2s-regs.h"
 
 #define ST_RUNNING		(1<<0)

sound/soc/samsung/pcm.c

@@ -127,25 +127,25 @@ struct s3c_pcm_info {
 	struct clk	*pclk;
 	struct clk	*cclk;
 
-	struct s3c_dma_params	*dma_playback;
-	struct s3c_dma_params	*dma_capture;
+	struct snd_dmaengine_dai_dma_data *dma_playback;
+	struct snd_dmaengine_dai_dma_data *dma_capture;
 };
 
-static struct s3c_dma_params s3c_pcm_stereo_out[] = {
+static struct snd_dmaengine_dai_dma_data s3c_pcm_stereo_out[] = {
 	[0] = {
-		.dma_size	= 4,
+		.addr_width	= 4,
 	},
 	[1] = {
-		.dma_size	= 4,
+		.addr_width	= 4,
 	},
 };
 
-static struct s3c_dma_params s3c_pcm_stereo_in[] = {
+static struct snd_dmaengine_dai_dma_data s3c_pcm_stereo_in[] = {
 	[0] = {
-		.dma_size	= 4,
+		.addr_width	= 4,
 	},
 	[1] = {
-		.dma_size	= 4,
+		.addr_width	= 4,
 	},
 };
 
@@ -552,15 +552,13 @@ static int s3c_pcm_dev_probe(struct platform_device *pdev)
 	}
 	clk_prepare_enable(pcm->pclk);
 
-	s3c_pcm_stereo_in[pdev->id].dma_addr = mem_res->start
-							+ S3C_PCM_RXFIFO;
-	s3c_pcm_stereo_out[pdev->id].dma_addr = mem_res->start
-							+ S3C_PCM_TXFIFO;
+	s3c_pcm_stereo_in[pdev->id].addr = mem_res->start + S3C_PCM_RXFIFO;
+	s3c_pcm_stereo_out[pdev->id].addr = mem_res->start + S3C_PCM_TXFIFO;
 
 	filter = NULL;
 	if (pcm_pdata) {
-		s3c_pcm_stereo_in[pdev->id].slave = pcm_pdata->dma_capture;
-		s3c_pcm_stereo_out[pdev->id].slave = pcm_pdata->dma_playback;
+		s3c_pcm_stereo_in[pdev->id].filter_data = pcm_pdata->dma_capture;
+		s3c_pcm_stereo_out[pdev->id].filter_data = pcm_pdata->dma_playback;
 		filter = pcm_pdata->dma_filter;
 	}
 

sound/soc/samsung/s3c-i2s-v2.c

@@ -24,7 +24,6 @@
 
 #include "regs-i2s-v2.h"
 #include "s3c-i2s-v2.h"
-#include "dma.h"
 
 #undef S3C_IIS_V2_SUPPORTED
 
@@ -302,7 +301,7 @@ static int s3c_i2sv2_hw_params(struct snd_pcm_substream *substream,
 				 struct snd_soc_dai *dai)
 {
 	struct s3c_i2sv2_info *i2s = to_info(dai);
-	struct s3c_dma_params *dma_data;
+	struct snd_dmaengine_dai_dma_data *dma_data;
 	u32 iismod;
 
 	pr_debug("Entered %s\n", __func__);

sound/soc/samsung/s3c-i2s-v2.h

@@ -60,8 +60,8 @@ struct s3c_i2sv2_info {
 
 	unsigned char	 master;
 
-	struct s3c_dma_params	*dma_playback;
-	struct s3c_dma_params	*dma_capture;
+	struct snd_dmaengine_dai_dma_data *dma_playback;
+	struct snd_dmaengine_dai_dma_data *dma_capture;
 
 	u32		 suspend_iismod;
 	u32		 suspend_iiscon;

sound/soc/samsung/s3c2412-i2s.c

@@ -34,14 +34,14 @@
 
 #include <linux/platform_data/asoc-s3c.h>
 
-static struct s3c_dma_params s3c2412_i2s_pcm_stereo_out = {
-	.ch_name	= "tx",
-	.dma_size	= 4,
+static struct snd_dmaengine_dai_dma_data s3c2412_i2s_pcm_stereo_out = {
+	.chan_name	= "tx",
+	.addr_width	= 4,
 };
 
-static struct s3c_dma_params s3c2412_i2s_pcm_stereo_in = {
-	.ch_name	= "rx",
-	.dma_size	= 4,
+static struct snd_dmaengine_dai_dma_data s3c2412_i2s_pcm_stereo_in = {
+	.chan_name	= "rx",
+	.addr_width	= 4,
 };
 
 static struct s3c_i2sv2_info s3c2412_i2s;
@@ -52,7 +52,7 @@ static int s3c2412_i2s_probe(struct snd_soc_dai *dai)
 
 	pr_debug("Entered %s\n", __func__);
 
-	samsung_asoc_init_dma_data(dai, &s3c2412_i2s_pcm_stereo_out,
+	snd_soc_dai_init_dma_data(dai, &s3c2412_i2s_pcm_stereo_out,
 					&s3c2412_i2s_pcm_stereo_in);
 
 	ret = s3c_i2sv2_probe(dai, &s3c2412_i2s, S3C2410_PA_IIS);
@@ -163,10 +163,10 @@ static int s3c2412_iis_dev_probe(struct platform_device *pdev)
 	if (IS_ERR(s3c2412_i2s.regs))
 		return PTR_ERR(s3c2412_i2s.regs);
 
-	s3c2412_i2s_pcm_stereo_out.dma_addr = res->start + S3C2412_IISTXD;
-	s3c2412_i2s_pcm_stereo_out.slave = pdata->dma_playback;
-	s3c2412_i2s_pcm_stereo_in.dma_addr = res->start + S3C2412_IISRXD;
-	s3c2412_i2s_pcm_stereo_in.slave = pdata->dma_capture;
+	s3c2412_i2s_pcm_stereo_out.addr = res->start + S3C2412_IISTXD;
+	s3c2412_i2s_pcm_stereo_out.filter_data = pdata->dma_playback;
+	s3c2412_i2s_pcm_stereo_in.addr = res->start + S3C2412_IISRXD;
+	s3c2412_i2s_pcm_stereo_in.filter_data = pdata->dma_capture;
 
 	ret = s3c_i2sv2_register_component(&pdev->dev, -1,
 					   &s3c2412_i2s_component,

sound/soc/samsung/s3c24xx-i2s.c

@@ -32,14 +32,14 @@
 
 #include <linux/platform_data/asoc-s3c.h>
 
-static struct s3c_dma_params s3c24xx_i2s_pcm_stereo_out = {
-	.ch_name	= "tx",
-	.dma_size	= 2,
+static struct snd_dmaengine_dai_dma_data s3c24xx_i2s_pcm_stereo_out = {
+	.chan_name	= "tx",
+	.addr_width	= 2,
 };
 
-static struct s3c_dma_params s3c24xx_i2s_pcm_stereo_in = {
-	.ch_name	= "rx",
-	.dma_size	= 2,
+static struct snd_dmaengine_dai_dma_data s3c24xx_i2s_pcm_stereo_in = {
+	.chan_name	= "rx",
+	.addr_width	= 2,
 };
 
 struct s3c24xx_i2s_info {
@@ -360,7 +360,7 @@ static int s3c24xx_i2s_probe(struct snd_soc_dai *dai)
 {
 	pr_debug("Entered %s\n", __func__);
 
-	samsung_asoc_init_dma_data(dai, &s3c24xx_i2s_pcm_stereo_out,
+	snd_soc_dai_init_dma_data(dai, &s3c24xx_i2s_pcm_stereo_out,
 					&s3c24xx_i2s_pcm_stereo_in);
 
 	s3c24xx_i2s.iis_clk = devm_clk_get(dai->dev, "iis");
@@ -469,10 +469,10 @@ static int s3c24xx_iis_dev_probe(struct platform_device *pdev)
 	if (IS_ERR(s3c24xx_i2s.regs))
 		return PTR_ERR(s3c24xx_i2s.regs);
 
-	s3c24xx_i2s_pcm_stereo_out.dma_addr = res->start + S3C2410_IISFIFO;
-	s3c24xx_i2s_pcm_stereo_out.slave = pdata->dma_playback;
-	s3c24xx_i2s_pcm_stereo_in.dma_addr = res->start + S3C2410_IISFIFO;
-	s3c24xx_i2s_pcm_stereo_in.slave = pdata->dma_capture;
+	s3c24xx_i2s_pcm_stereo_out.addr = res->start + S3C2410_IISFIFO;
+	s3c24xx_i2s_pcm_stereo_out.filter_data = pdata->dma_playback;
+	s3c24xx_i2s_pcm_stereo_in.addr = res->start + S3C2410_IISFIFO;
+	s3c24xx_i2s_pcm_stereo_in.filter_data = pdata->dma_capture;
 
 	ret = devm_snd_soc_register_component(&pdev->dev,
 			&s3c24xx_i2s_component, &s3c24xx_i2s_dai, 1);

sound/soc/samsung/s3c24xx_uda134x.c

@@ -54,8 +54,6 @@ static struct snd_pcm_hw_constraint_list hw_constraints_rates = {
 };
 #endif
 
-static struct platform_device *s3c24xx_uda134x_snd_device;
-
 static int s3c24xx_uda134x_startup(struct snd_pcm_substream *substream)
 {
 	struct snd_soc_pcm_runtime *rtd = substream->private_data;
@@ -66,16 +64,16 @@ static int s3c24xx_uda134x_startup(struct snd_pcm_substream *substream)
 	int ret = 0;
 
 	mutex_lock(&clk_lock);
-	pr_debug("%s %d\n", __func__, clk_users);
+
 	if (clk_users == 0) {
-		xtal = clk_get(&s3c24xx_uda134x_snd_device->dev, "xtal");
+		xtal = clk_get(rtd->dev, "xtal");
 		if (IS_ERR(xtal)) {
-			printk(KERN_ERR "%s cannot get xtal\n", __func__);
+			dev_err(rtd->dev, "%s cannot get xtal\n", __func__);
 			ret = PTR_ERR(xtal);
 		} else {
 			pclk = clk_get(cpu_dai->dev, "iis");
 			if (IS_ERR(pclk)) {
-				printk(KERN_ERR "%s cannot get pclk\n",
+				dev_err(rtd->dev, "%s cannot get pclk\n",
 					__func__);
 				clk_put(xtal);
 				ret = PTR_ERR(pclk);
@@ -102,7 +100,7 @@ static int s3c24xx_uda134x_startup(struct snd_pcm_substream *substream)
 						 SNDRV_PCM_HW_PARAM_RATE,
 						 &hw_constraints_rates);
 		if (ret < 0)
-			printk(KERN_ERR "%s cannot set constraints\n",
+			dev_err(rtd->dev, "%s cannot set constraints\n",
 				__func__);
 #endif
 	}
@@ -112,7 +110,6 @@ static int s3c24xx_uda134x_startup(struct snd_pcm_substream *substream)
 static void s3c24xx_uda134x_shutdown(struct snd_pcm_substream *substream)
 {
 	mutex_lock(&clk_lock);
-	pr_debug("%s %d\n", __func__, clk_users);
 	clk_users -= 1;
 	if (clk_users == 0) {
 		clk_put(xtal);
@@ -159,18 +156,19 @@ static int s3c24xx_uda134x_hw_params(struct snd_pcm_substream *substream,
 		clk_source = S3C24XX_CLKSRC_PCLK;
 		div = bi % 33;
 	}
-	pr_debug("%s desired rate %lu, %d\n", __func__, rate, bi);
+
+	dev_dbg(rtd->dev, "%s desired rate %lu, %d\n", __func__, rate, bi);
 
 	clk = (fs_mode == S3C2410_IISMOD_384FS ? 384 : 256) * rate;
-	pr_debug("%s will use: %s %s %d sysclk %d err %ld\n", __func__,
+
+	dev_dbg(rtd->dev, "%s will use: %s %s %d sysclk %d err %ld\n", __func__,
 		fs_mode == S3C2410_IISMOD_384FS ? "384FS" : "256FS",
 		clk_source == S3C24XX_CLKSRC_MPLL ? "MPLLin" : "PCLK",
 		div, clk, err);
 
 	if ((err * 100 / rate) > 5) {
-		printk(KERN_ERR "S3C24XX_UDA134X: effective frequency "
-		       "too different from desired (%ld%%)\n",
-		       err * 100 / rate);
+		dev_err(rtd->dev, "effective frequency too different "
+				  "from desired (%ld%%)\n", err * 100 / rate);
 		return -EINVAL;
 	}
 
@@ -227,115 +225,27 @@ static struct snd_soc_card snd_soc_s3c24xx_uda134x = {
 	.num_links = 1,
 };
 
-static struct s3c24xx_uda134x_platform_data *s3c24xx_uda134x_l3_pins;
-
-static void setdat(int v)
-{
-	gpio_set_value(s3c24xx_uda134x_l3_pins->l3_data, v > 0);
-}
-
-static void setclk(int v)
-{
-	gpio_set_value(s3c24xx_uda134x_l3_pins->l3_clk, v > 0);
-}
-
-static void setmode(int v)
-{
-	gpio_set_value(s3c24xx_uda134x_l3_pins->l3_mode, v > 0);
-}
-
-/* FIXME - This must be codec platform data but in which board file ?? */
-static struct uda134x_platform_data s3c24xx_uda134x = {
-	.l3 = {
-		.setdat = setdat,
-		.setclk = setclk,
-		.setmode = setmode,
-		.data_hold = 1,
-		.data_setup = 1,
-		.clock_high = 1,
-		.mode_hold = 1,
-		.mode = 1,
-		.mode_setup = 1,
-	},
-};
-
-static int s3c24xx_uda134x_setup_pin(int pin, char *fun)
-{
-	if (gpio_request(pin, "s3c24xx_uda134x") < 0) {
-		printk(KERN_ERR "S3C24XX_UDA134X SoC Audio: "
-		       "l3 %s pin already in use", fun);
-		return -EBUSY;
-	}
-	gpio_direction_output(pin, 0);
-	return 0;
-}
-
 static int s3c24xx_uda134x_probe(struct platform_device *pdev)
 {
+	struct snd_soc_card *card = &snd_soc_s3c24xx_uda134x;
 	int ret;
 
-	printk(KERN_INFO "S3C24XX_UDA134X SoC Audio driver\n");
+	platform_set_drvdata(pdev, card);
+	card->dev = &pdev->dev;
 
-	s3c24xx_uda134x_l3_pins = pdev->dev.platform_data;
-	if (s3c24xx_uda134x_l3_pins == NULL) {
-		printk(KERN_ERR "S3C24XX_UDA134X SoC Audio: "
-		       "unable to find platform data\n");
-		return -ENODEV;
-	}
-	s3c24xx_uda134x.power = s3c24xx_uda134x_l3_pins->power;
-	s3c24xx_uda134x.model = s3c24xx_uda134x_l3_pins->model;
-
-	if (s3c24xx_uda134x_setup_pin(s3c24xx_uda134x_l3_pins->l3_data,
-				      "data") < 0)
-		return -EBUSY;
-	if (s3c24xx_uda134x_setup_pin(s3c24xx_uda134x_l3_pins->l3_clk,
-				      "clk") < 0) {
-		gpio_free(s3c24xx_uda134x_l3_pins->l3_data);
-		return -EBUSY;
-	}
-	if (s3c24xx_uda134x_setup_pin(s3c24xx_uda134x_l3_pins->l3_mode,
-				      "mode") < 0) {
-		gpio_free(s3c24xx_uda134x_l3_pins->l3_data);
-		gpio_free(s3c24xx_uda134x_l3_pins->l3_clk);
-		return -EBUSY;
-	}
-
-	s3c24xx_uda134x_snd_device = platform_device_alloc("soc-audio", -1);
-	if (!s3c24xx_uda134x_snd_device) {
-		printk(KERN_ERR "S3C24XX_UDA134X SoC Audio: "
-		       "Unable to register\n");
-		return -ENOMEM;
-	}
-
-	platform_set_drvdata(s3c24xx_uda134x_snd_device,
-			     &snd_soc_s3c24xx_uda134x);
-	platform_device_add_data(s3c24xx_uda134x_snd_device, &s3c24xx_uda134x, sizeof(s3c24xx_uda134x));
-	ret = platform_device_add(s3c24xx_uda134x_snd_device);
-	if (ret) {
-		printk(KERN_ERR "S3C24XX_UDA134X SoC Audio: Unable to add\n");
-		platform_device_put(s3c24xx_uda134x_snd_device);
-	}
+	ret = devm_snd_soc_register_card(&pdev->dev, card);
+	if (ret)
+		dev_err(&pdev->dev, "failed to register card: %d\n", ret);
 
 	return ret;
 }
 
-static int s3c24xx_uda134x_remove(struct platform_device *pdev)
-{
-	platform_device_unregister(s3c24xx_uda134x_snd_device);
-	gpio_free(s3c24xx_uda134x_l3_pins->l3_data);
-	gpio_free(s3c24xx_uda134x_l3_pins->l3_clk);
-	gpio_free(s3c24xx_uda134x_l3_pins->l3_mode);
-	return 0;
-}
-
 static struct platform_driver s3c24xx_uda134x_driver = {
 	.probe  = s3c24xx_uda134x_probe,
-	.remove = s3c24xx_uda134x_remove,
 	.driver = {
 		.name = "s3c24xx_uda134x",
 	},
 };
-
 module_platform_driver(s3c24xx_uda134x_driver);
 
 MODULE_AUTHOR("Zoltan Devai, Christian Pellegrin <chripell@evolware.org>");

sound/soc/samsung/smdk_wm8580pcm.c

@@ -16,7 +16,6 @@
 #include <asm/mach-types.h>
 
 #include "../codecs/wm8580.h"
-#include "dma.h"
 #include "pcm.h"
 
 /*

sound/soc/samsung/smdk_wm8994pcm.c

@@ -15,7 +15,6 @@
 #include <sound/pcm_params.h>
 
 #include "../codecs/wm8994.h"
-#include "dma.h"
 #include "pcm.h"
 
 /*

sound/soc/samsung/spdif.c

@@ -90,10 +90,10 @@ struct samsung_spdif_info {
 	u32		saved_clkcon;
 	u32		saved_con;
 	u32		saved_cstas;
-	struct s3c_dma_params	*dma_playback;
+	struct snd_dmaengine_dai_dma_data *dma_playback;
 };
 
-static struct s3c_dma_params spdif_stereo_out;
+static struct snd_dmaengine_dai_dma_data spdif_stereo_out;
 static struct samsung_spdif_info spdif_info;
 
 static inline struct samsung_spdif_info *to_info(struct snd_soc_dai *cpu_dai)
@@ -179,7 +179,7 @@ static int spdif_hw_params(struct snd_pcm_substream *substream,
 	struct snd_soc_pcm_runtime *rtd = substream->private_data;
 	struct samsung_spdif_info *spdif = to_info(rtd->cpu_dai);
 	void __iomem *regs = spdif->regs;
-	struct s3c_dma_params *dma_data;
+	struct snd_dmaengine_dai_dma_data *dma_data;
 	u32 con, clkcon, cstas;
 	unsigned long flags;
 	int i, ratio;
@@ -425,11 +425,11 @@ static int spdif_probe(struct platform_device *pdev)
 		goto err4;
 	}
 
-	spdif_stereo_out.dma_size = 2;
-	spdif_stereo_out.dma_addr = mem_res->start + DATA_OUTBUF;
+	spdif_stereo_out.addr_width = 2;
+	spdif_stereo_out.addr = mem_res->start + DATA_OUTBUF;
 	filter = NULL;
 	if (spdif_pdata) {
-		spdif_stereo_out.slave = spdif_pdata->dma_playback;
+		spdif_stereo_out.filter_data = spdif_pdata->dma_playback;
 		filter = spdif_pdata->dma_filter;
 	}