Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC device-tree updates, take 2, from Olof Johansson:
 "This branch contains device-tree updates for the SPEAr platform.  They
  had dependencies on earlier branches from this merge window, which is
  why they were broken out in a separate branch."

* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: SPEAr3xx: Shirq: Move shirq controller out of plat/
  ARM: SPEAr320: DT: Add SPEAr 320 HMI board support
  ARM: SPEAr3xx: DT: add shirq node for interrupt multiplexor
  ARM: SPEAr3xx: shirq: simplify and move the shared irq multiplexor to DT
  ARM: SPEAr1310: Fix AUXDATA for compact flash controller
  ARM: SPEAr13xx: Remove fields not required for ssp controller
  ARM: SPEAr1310: Move 1310 specific misc register into machine specific files
  ARM: SPEAr: DT: Update device nodes
  ARM: SPEAr: DT: add uart state to fix warning
  ARM: SPEAr: DT: Modify DT bindings for STMMAC
  ARM: SPEAr: DT: Fix existing DT support
  ARM: SPEAr: DT: Update partition info for MTD devices
  ARM: SPEAr: DT: Update pinctrl list
  ARM: SPEAr13xx: DT: Add spics gpio controller nodes

Documentation/devicetree/bindings/arm/spear/shirq.txt

+* SPEAr Shared IRQ layer (shirq)
+
+SPEAr3xx architecture includes shared/multiplexed irqs for certain set
+of devices. The multiplexor provides a single interrupt to parent
+interrupt controller (VIC) on behalf of a group of devices.
+
+There can be multiple groups available on SPEAr3xx variants but not
+exceeding 4. The number of devices in a group can differ, further they
+may share same set of status/mask registers spanning across different
+bit masks. Also in some cases the group may not have enable or other
+registers. This makes software little complex.
+
+A single node in the device tree is used to describe the shared
+interrupt multiplexor (one node for all groups). A group in the
+interrupt controller shares config/control registers with other groups.
+For example, a 32-bit interrupt enable/disable config register can
+accommodate upto 4 interrupt groups.
+
+Required properties:
+  - compatible: should be, either of
+     - "st,spear300-shirq"
+     - "st,spear310-shirq"
+     - "st,spear320-shirq"
+  - interrupt-controller: Identifies the node as an interrupt controller.
+  - #interrupt-cells: should be <1> which basically contains the offset
+    (starting from 0) of interrupts for all the groups.
+  - reg: Base address and size of shirq registers.
+  - interrupts: The list of interrupts generated by the groups which are
+    then connected to a parent interrupt controller. Each group is
+    associated with one of the interrupts, hence number of interrupts (to
+    parent) is equal to number of groups. The format of the interrupt
+    specifier depends in the interrupt parent controller.
+
+  Optional properties:
+  - interrupt-parent: pHandle of the parent interrupt controller, if not
+    inherited from the parent node.
+
+Example:
+
+The following is an example from the SPEAr320 SoC dtsi file.
+
+shirq: interrupt-controller@0xb3000000 {
+	compatible = "st,spear320-shirq";
+	reg = <0xb3000000 0x1000>;
+	interrupts = <28 29 30 1>;
+	#interrupt-cells = <1>;
+	interrupt-controller;
+};

arch/arm/boot/dts/Makefile

@@ -126,7 +126,8 @@ dtb-$(CONFIG_ARCH_SPEAR13XX) += spear1310-evb.dtb \
 	spear1340-evb.dtb
 dtb-$(CONFIG_ARCH_SPEAR3XX)+= spear300-evb.dtb \
 	spear310-evb.dtb \
-	spear320-evb.dtb
+	spear320-evb.dtb \
+	spear320-hmi.dtb
 dtb-$(CONFIG_ARCH_SPEAR6XX)+= spear600-evb.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun4i-cubieboard.dtb \
 	sun5i-olinuxino.dtb

arch/arm/boot/dts/spear1310-evb.dts

@@ -30,10 +30,14 @@ pinmux@e0700000 {
 			pinctrl-0 = <&state_default>;
 
 			state_default: pinmux {
-				i2c0-pmx {
+				i2c0 {
 					st,pins = "i2c0_grp";
 					st,function = "i2c0";
 				};
+				i2s0 {
+					st,pins = "i2s0_grp";
+					st,function = "i2s0";
+				};
 				i2s1 {
 					st,pins = "i2s1_grp";
 					st,function = "i2s1";
@@ -42,6 +46,10 @@ gpio {
 					st,pins = "arm_gpio_grp";
 					st,function = "arm_gpio";
 				};
+				clcd {
+					st,pins = "clcd_grp" , "clcd_high_res";
+					st,function = "clcd";
+				};
 				eth {
 					st,pins = "gmii_grp";
 					st,function = "gmii";
@@ -74,11 +82,6 @@ i2c1_2 {
 					st,pins = "i2c_1_2_grp";
 					st,function = "i2c_1_2";
 				};
-				pci {
-					st,pins = "pcie0_grp","pcie1_grp",
-						"pcie2_grp";
-					st,function = "pci";
-				};
 				smii {
 					st,pins = "smii_0_1_2_grp";
 					st,function = "smii_0_1_2";
@@ -88,6 +91,14 @@ nand {
 						"nand_16bit_grp";
 					st,function = "nand";
 				};
+				sata {
+					st,pins = "sata0_grp";
+					st,function = "sata";
+				};
+				pcie {
+					st,pins = "pcie1_grp", "pcie2_grp";
+					st,function = "pci_express";
+				};
 			};
 		};
 
@@ -109,9 +120,49 @@ dma@eb000000 {
 
 		fsmc: flash@b0000000 {
 			status = "okay";
+
+			partition@0 {
+				label = "xloader";
+				reg = <0x0 0x80000>;
+			};
+			partition@80000 {
+				label = "u-boot";
+				reg = <0x80000 0x140000>;
+			};
+			partition@1C0000 {
+				label = "environment";
+				reg = <0x1C0000 0x40000>;
+			};
+			partition@200000 {
+				label = "dtb";
+				reg = <0x200000 0x40000>;
+			};
+			partition@240000 {
+				label = "linux";
+				reg = <0x240000 0xC00000>;
+			};
+			partition@E40000 {
+				label = "rootfs";
+				reg = <0xE40000 0x0>;
+			};
+		};
+
+		gpio_keys {
+			compatible = "gpio-keys";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			button@1 {
+				label = "wakeup";
+				linux,code = <0x100>;
+				gpios = <&gpio0 7 0x4>;
+				debounce-interval = <20>;
+				gpio-key,wakeup = <1>;
+			};
 		};
 
 		gmac0: eth@e2000000 {
+			phy-mode = "gmii";
 			status = "okay";
 		};
 
@@ -135,21 +186,25 @@ partition@0 {
 				};
 				partition@10000 {
 					label = "u-boot";
-					reg = <0x10000 0x40000>;
+					reg = <0x10000 0x50000>;
+				};
+				partition@60000 {
+					label = "environment";
+					reg = <0x60000 0x10000>;
 				};
-				partition@50000 {
+				partition@70000 {
+					label = "dtb";
+					reg = <0x70000 0x10000>;
+				};
+				partition@80000 {
 					label = "linux";
-					reg = <0x50000 0x2c0000>;
+					reg = <0x80000 0x310000>;
 				};
-				partition@310000 {
+				partition@390000 {
 					label = "rootfs";
-					reg = <0x310000 0x4f0000>;
-				};
+					reg = <0x390000 0x0>;
 				};
 			};
-
-		spi0: spi@e0100000 {
-			status = "okay";
 		};
 
 		ehci@e4800000 {
@@ -189,10 +244,6 @@ i2c0: i2c@e0280000 {
 			       status = "okay";
 			};
 
-			i2c1: i2c@5cd00000 {
-			       status = "okay";
-			};
-
 			kbd@e0300000 {
 				linux,keymap = < 0x00000001
 						 0x00010002
@@ -277,6 +328,7 @@ kbd@e0300000 {
 						 0x08080052 >;
 			       autorepeat;
 			       st,mode = <0>;
+			       suspended_rate = <2000000>;
 			       status = "okay";
 			};
 
@@ -286,6 +338,81 @@ rtc@e0580000 {
 
 			serial@e0000000 {
 			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
+			};
+
+			spi0: spi@e0100000 {
+				status = "okay";
+				num-cs = <3>;
+				cs-gpios = <&gpio1 7 0>, <&spics 0>, <&spics 1>;
+
+				stmpe610@0 {
+					compatible = "st,stmpe610";
+					reg = <0>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					spi-max-frequency = <1000000>;
+					spi-cpha;
+					pl022,hierarchy = <0>;
+					pl022,interface = <0>;
+					pl022,slave-tx-disable;
+					pl022,com-mode = <0>;
+					pl022,rx-level-trig = <0>;
+					pl022,tx-level-trig = <0>;
+					pl022,ctrl-len = <0x7>;
+					pl022,wait-state = <0>;
+					pl022,duplex = <0>;
+					interrupts = <6 0x4>;
+					interrupt-parent = <&gpio1>;
+					irq-trigger = <0x2>;
+
+					stmpe_touchscreen {
+						compatible = "st,stmpe-ts";
+						ts,sample-time = <4>;
+						ts,mod-12b = <1>;
+						ts,ref-sel = <0>;
+						ts,adc-freq = <1>;
+						ts,ave-ctrl = <1>;
+						ts,touch-det-delay = <2>;
+						ts,settling = <2>;
+						ts,fraction-z = <7>;
+						ts,i-drive = <1>;
+					};
+				};
+
+				m25p80@1 {
+					compatible = "st,m25p80";
+					reg = <1>;
+					spi-max-frequency = <12000000>;
+					spi-cpol;
+					spi-cpha;
+					pl022,hierarchy = <0>;
+					pl022,interface = <0>;
+					pl022,slave-tx-disable;
+					pl022,com-mode = <0x2>;
+					pl022,rx-level-trig = <0>;
+					pl022,tx-level-trig = <0>;
+					pl022,ctrl-len = <0x11>;
+					pl022,wait-state = <0>;
+					pl022,duplex = <0>;
+				};
+
+				spidev@2 {
+					compatible = "spidev";
+					reg = <2>;
+					spi-max-frequency = <25000000>;
+					spi-cpha;
+					pl022,hierarchy = <0>;
+					pl022,interface = <0>;
+					pl022,slave-tx-disable;
+					pl022,com-mode = <0x2>;
+					pl022,rx-level-trig = <0>;
+					pl022,tx-level-trig = <0>;
+					pl022,ctrl-len = <0x11>;
+					pl022,wait-state = <0>;
+					pl022,duplex = <0>;
+				};
 			};
 
 			wdt@ec800620 {

arch/arm/boot/dts/spear1310.dtsi

@@ -17,6 +17,18 @@ / {
 	compatible = "st,spear1310";
 
 	ahb {
+		spics: spics@e0700000{
+			compatible = "st,spear-spics-gpio";
+			reg = <0xe0700000 0x1000>;
+			st-spics,peripcfg-reg = <0x3b0>;
+			st-spics,sw-enable-bit = <12>;
+			st-spics,cs-value-bit = <11>;
+			st-spics,cs-enable-mask = <3>;
+			st-spics,cs-enable-shift = <8>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
 		ahci@b1000000 {
 			compatible = "snps,spear-ahci";
 			reg = <0xb1000000 0x10000>;
@@ -43,6 +55,7 @@ gmac1: eth@5c400000 {
 			reg = <0x5c400000 0x8000>;
 			interrupts = <0 95 0x4>;
 			interrupt-names = "macirq";
+			phy-mode = "mii";
 			status = "disabled";
 		};
 
@@ -51,6 +64,7 @@ gmac2: eth@5c500000 {
 			reg = <0x5c500000 0x8000>;
 			interrupts = <0 96 0x4>;
 			interrupt-names = "macirq";
+			phy-mode = "mii";
 			status = "disabled";
 		};
 
@@ -59,6 +73,7 @@ gmac3: eth@5c600000 {
 			reg = <0x5c600000 0x8000>;
 			interrupts = <0 97 0x4>;
 			interrupt-names = "macirq";
+			phy-mode = "rmii";
 			status = "disabled";
 		};
 
@@ -67,6 +82,7 @@ gmac4: eth@5c700000 {
 			reg = <0x5c700000 0x8000>;
 			interrupts = <0 98 0x4>;
 			interrupt-names = "macirq";
+			phy-mode = "rgmii";
 			status = "disabled";
 		};
 
@@ -76,13 +92,6 @@ pinmux: pinmux@e0700000 {
 			#gpio-range-cells = <2>;
 		};
 
-		spi1: spi@5d400000 {
-			compatible = "arm,pl022", "arm,primecell";
-			reg = <0x5d400000 0x1000>;
-			interrupts = <0 99 0x4>;
-			status = "disabled";
-		};
-
 		apb {
 			i2c1: i2c@5cd00000 {
 				#address-cells = <1>;
@@ -147,6 +156,15 @@ i2c7: i2c@5d300000 {
 				status = "disabled";
 			};
 
+			spi1: spi@5d400000 {
+				compatible = "arm,pl022", "arm,primecell";
+				reg = <0x5d400000 0x1000>;
+				interrupts = <0 99 0x4>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
 			serial@5c800000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0x5c800000 0x1000>;

arch/arm/boot/dts/spear1340-evb.dts

@@ -38,20 +38,15 @@ fsmc {
 					st,pins = "fsmc_8bit_grp";
 					st,function = "fsmc";
 				};
-				kbd {
-					st,pins = "keyboard_row_col_grp",
-						"keyboard_col5_grp";
-					st,function = "keyboard";
-				};
 				uart0 {
-					st,pins = "uart0_grp", "uart0_enh_grp";
+					st,pins = "uart0_grp";
 					st,function = "uart0";
 				};
-				i2c0-pmx {
+				i2c0 {
 					st,pins = "i2c0_grp";
 					st,function = "i2c0";
 				};
-				i2c1-pmx {
+				i2c1 {
 					st,pins = "i2c1_grp";
 					st,function = "i2c1";
 				};
@@ -64,14 +59,9 @@ spdif-out {
 					st,function = "spdif_out";
 				};
 				ssp0 {
-					st,pins = "ssp0_grp", "ssp0_cs1_grp",
-						"ssp0_cs3_grp";
+					st,pins = "ssp0_grp", "ssp0_cs1_grp", "ssp0_cs2_grp", "ssp0_cs3_grp";
 					st,function = "ssp0";
 				};
-				pwm {
-					st,pins = "pwm2_grp", "pwm3_grp";
-					st,function = "pwm";
-				};
 				smi-pmx {
 					st,pins = "smi_grp";
 					st,function = "smi";
@@ -84,6 +74,18 @@ gmac {
 					st,pins = "gmii_grp", "rgmii_grp";
 					st,function = "gmac";
 				};
+				cam0 {
+					st,pins = "cam0_grp";
+					st,function = "cam0";
+				};
+				cam1 {
+					st,pins = "cam1_grp";
+					st,function = "cam1";
+				};
+				cam2 {
+					st,pins = "cam2_grp";
+					st,function = "cam2";
+				};
 				cam3 {
 					st,pins = "cam3_grp";
 					st,function = "cam3";
@@ -108,9 +110,18 @@ sata {
 					st,pins = "sata_grp";
 					st,function = "sata";
 				};
+				pcie {
+					st,pins = "pcie_grp";
+					st,function = "pcie";
+				};
+
 			};
 		};
 
+		ahci@b1000000 {
+			status = "okay";
+		};
+
 		dma@ea800000 {
 			status = "okay";
 		};
@@ -121,9 +132,35 @@ dma@eb000000 {
 
 		fsmc: flash@b0000000 {
 			status = "okay";
+
+			partition@0 {
+				label = "xloader";
+				reg = <0x0 0x200000>;
+			};
+			partition@200000 {
+				label = "u-boot";
+				reg = <0x200000 0x200000>;
+			};
+			partition@400000 {
+				label = "environment";
+				reg = <0x400000 0x100000>;
+			};
+			partition@500000 {
+				label = "dtb";
+				reg = <0x500000 0x100000>;
+			};
+			partition@600000 {
+				label = "linux";
+				reg = <0x600000 0xC00000>;
+			};
+			partition@1200000 {
+				label = "rootfs";
+				reg = <0x1200000 0x0>;
+			};
 		};
 
 		gmac0: eth@e2000000 {
+			phy-mode = "rgmii";
 			status = "okay";
 		};
 
@@ -147,31 +184,62 @@ partition@0 {
 				};
 				partition@10000 {
 					label = "u-boot";
-					reg = <0x10000 0x40000>;
+					reg = <0x10000 0x50000>;
 				};
-				partition@50000 {
+				partition@60000 {
+					label = "environment";
+					reg = <0x60000 0x10000>;
+				};
+				partition@70000 {
+					label = "dtb";
+					reg = <0x70000 0x10000>;
+				};
+				partition@80000 {
 					label = "linux";
-					reg = <0x50000 0x2c0000>;
+					reg = <0x80000 0x310000>;
 				};
-				partition@310000 {
+				partition@390000 {
 					label = "rootfs";
-					reg = <0x310000 0x4f0000>;
+					reg = <0x390000 0x0>;
 				};
 			};
 		};
 
-		spi0: spi@e0100000 {
+		ehci@e4800000 {
 			status = "okay";
 		};
 
-		ehci@e4800000 {
-			status = "okay";
+		gpio_keys {
+			compatible = "gpio-keys";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			button@1 {
+				label = "wakeup";
+				linux,code = <0x100>;
+				gpios = <&gpio1 1 0x4>;
+				debounce-interval = <20>;
+				gpio-key,wakeup = <1>;
+			};
 		};
 
 		ehci@e5800000 {
 			status = "okay";
 		};
 
+		i2s0: i2s-play@b2400000 {
+			status = "okay";
+		};
+
+		i2s1: i2s-rec@b2000000 {
+			status = "okay";
+		};
+
+		incodec: dir-hifi {
+			compatible = "dummy,dir-hifi";
+			status = "okay";
+		};
+
 		ohci@e4000000 {
 			status = "okay";
 		};
@@ -180,11 +248,43 @@ ohci@e5000000 {
 			status = "okay";
 		};
 
+		outcodec: dit-hifi {
+			compatible = "dummy,dit-hifi";
+			status = "okay";
+		};
+
+		sound {
+			compatible = "spear,spear-evb";
+			audio-controllers = <&spdif0 &spdif1 &i2s0 &i2s1>;
+			audio-codecs = <&incodec &outcodec &sta529 &sta529>;
+			codec_dai_name = "dir-hifi", "dit-hifi", "sta529-audio", "sta529-audio";
+			stream_name = "spdif-cap", "spdif-play", "i2s-play", "i2s-cap";
+			dai_name = "spdifin-pcm", "spdifout-pcm", "i2s0-pcm", "i2s1-pcm";
+			nr_controllers = <4>;
+		        status = "okay";
+		};
+
+		spdif0: spdif-in@d0100000 {
+			status = "okay";
+		};
+
+		spdif1: spdif-out@d0000000 {
+			status = "okay";
+		};
+
 		apb {
 			adc@e0080000 {
 				status = "okay";
 			};
 
+			i2s-play@b2400000 {
+				status = "okay";
+			};
+
+			i2s-rec@b2000000 {
+				status = "okay";
+			};
+
 			gpio0: gpio@e0600000 {
 			       status = "okay";
 			};
@@ -199,10 +299,36 @@ gpio@e2800000 {
 
 			i2c0: i2c@e0280000 {
 			       status = "okay";
+
+				sta529: sta529@1a {
+					compatible = "st,sta529";
+					reg = <0x1a>;
+				};
 			};
 
 			i2c1: i2c@b4000000 {
 			       status = "okay";
+
+				eeprom0@56 {
+					compatible = "st,eeprom";
+					reg = <0x56>;
+				};
+
+				stmpe801@41 {
+					compatible = "st,stmpe801";
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x41>;
+					interrupts = <4 0x4>;
+					interrupt-parent = <&gpio0>;
+					irq-trigger = <0x2>;
+
+					stmpegpio: stmpe_gpio {
+						compatible = "st,stmpe-gpio";
+						gpio-controller;
+						#gpio-cells = <2>;
+					};
+				};
 			};
 
 			kbd@e0300000 {
@@ -289,6 +415,7 @@ kbd@e0300000 {
 						 0x08080052 >;
 			       autorepeat;
 			       st,mode = <0>;
+			       suspended_rate = <2000000>;
 			       status = "okay";
 			};
 
@@ -298,10 +425,92 @@ rtc@e0580000 {
 
 			serial@e0000000 {
 			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
 			};
 
 			serial@b4100000 {
 			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
+			};
+
+			spi0: spi@e0100000 {
+				status = "okay";
+				num-cs = <3>;
+				cs-gpios = <&gpiopinctrl 80 0>, <&gpiopinctrl 24 0>,
+					   <&gpiopinctrl 85 0>;
+
+				m25p80@0 {
+					compatible = "m25p80";
+					reg = <0>;
+					spi-max-frequency = <12000000>;
+					spi-cpol;
+					spi-cpha;
+					pl022,hierarchy = <0>;
+					pl022,interface = <0>;
+					pl022,slave-tx-disable;
+					pl022,com-mode = <0x2>;
+					pl022,rx-level-trig = <0>;
+					pl022,tx-level-trig = <0>;
+					pl022,ctrl-len = <0x11>;
+					pl022,wait-state = <0>;
+					pl022,duplex = <0>;
+				};
+
+				stmpe610@1 {
+					compatible = "st,stmpe610";
+					spi-max-frequency = <1000000>;
+					spi-cpha;
+					reg = <1>;
+					pl022,hierarchy = <0>;
+					pl022,interface = <0>;
+					pl022,slave-tx-disable;
+					pl022,com-mode = <0>;
+					pl022,rx-level-trig = <0>;
+					pl022,tx-level-trig = <0>;
+					pl022,ctrl-len = <0x7>;
+					pl022,wait-state = <0>;
+					pl022,duplex = <0>;
+					interrupts = <100 0>;
+					interrupt-parent = <&gpiopinctrl>;
+					irq-trigger = <0x2>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					stmpe_touchscreen {
+						compatible = "st,stmpe-ts";
+						ts,sample-time = <4>;
+						ts,mod-12b = <1>;
+						ts,ref-sel = <0>;
+						ts,adc-freq = <1>;
+						ts,ave-ctrl = <1>;
+						ts,touch-det-delay = <2>;
+						ts,settling = <2>;
+						ts,fraction-z = <7>;
+						ts,i-drive = <1>;
+					};
+				};
+
+				spidev@2 {
+					compatible = "spidev";
+					reg = <2>;
+					spi-max-frequency = <25000000>;
+					spi-cpha;
+					pl022,hierarchy = <0>;
+					pl022,interface = <0>;
+					pl022,slave-tx-disable;
+					pl022,com-mode = <0x2>;
+					pl022,rx-level-trig = <0>;
+					pl022,tx-level-trig = <0>;
+					pl022,ctrl-len = <0x11>;
+					pl022,wait-state = <0>;
+					pl022,duplex = <0>;
+				};
+			};
+
+			timer@ec800600 {
+				status = "okay";
 			};
 
 			wdt@ec800620 {

arch/arm/boot/dts/spear1340.dtsi

@@ -17,6 +17,20 @@ / {
 	compatible = "st,spear1340";
 
 	ahb {
+
+		spics: spics@e0700000{
+			compatible = "st,spear-spics-gpio";
+			reg = <0xe0700000 0x1000>;
+			st-spics,peripcfg-reg = <0x42c>;
+			st-spics,sw-enable-bit = <21>;
+			st-spics,cs-value-bit = <20>;
+			st-spics,cs-enable-mask = <3>;
+			st-spics,cs-enable-shift = <18>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
 		ahci@b1000000 {
 			compatible = "snps,spear-ahci";
 			reg = <0xb1000000 0x10000>;
@@ -24,15 +38,61 @@ ahci@b1000000 {
 			status = "disabled";
 		};
 
+		i2s-play@b2400000 {
+			compatible = "snps,designware-i2s";
+			reg = <0xb2400000 0x10000>;
+			interrupt-names = "play_irq";
+			interrupts = <0 98 0x4
+				      0 99 0x4>;
+			play;
+			channel = <8>;
+			status = "disabled";
+		};
+
+		i2s-rec@b2000000 {
+			compatible = "snps,designware-i2s";
+			reg = <0xb2000000 0x10000>;
+			interrupt-names = "record_irq";
+			interrupts = <0 100  0x4
+				      0 101 0x4>;
+			record;
+			channel = <8>;
+			status = "disabled";
+		};
+
 		pinmux: pinmux@e0700000 {
 			compatible = "st,spear1340-pinmux";
 			reg = <0xe0700000 0x1000>;
 			#gpio-range-cells = <2>;
 		};
 
+		pwm: pwm@e0180000 {
+			compatible ="st,spear13xx-pwm";
+			reg = <0xe0180000 0x1000>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		spdif-in@d0100000 {
+			compatible = "st,spdif-in";
+			reg = < 0xd0100000 0x20000
+				0xd0110000 0x10000 >;
+			interrupts = <0 84 0x4>;
+			status = "disabled";
+		};
+
+		spdif-out@d0000000 {
+			compatible = "st,spdif-out";
+			reg = <0xd0000000 0x20000>;
+			interrupts = <0 85 0x4>;
+			status = "disabled";
+		};
+
 		spi1: spi@5d400000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x5d400000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
 			interrupts = <0 99 0x4>;
 			status = "disabled";
 		};
@@ -44,6 +104,7 @@ i2c1: i2c@b4000000 {
 				compatible = "snps,designware-i2c";
 				reg = <0xb4000000 0x1000>;
 				interrupts = <0 104 0x4>;
+				write-16bit;
 				status = "disabled";
 			};
 

arch/arm/boot/dts/spear13xx.dtsi

@@ -64,12 +64,26 @@ chosen {
 		bootargs = "console=ttyAMA0,115200";
 	};
 
+	cpufreq {
+		compatible = "st,cpufreq-spear";
+		cpufreq_tbl = < 166000
+				200000
+				250000
+				300000
+				400000
+				500000
+				600000 >;
+		status = "disable";
+	};
+
 	ahb {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
 		ranges = <0x50000000 0x50000000 0x10000000
 			  0xb0000000 0xb0000000 0x10000000
+			  0xd0000000 0xd0000000 0x02000000
+			  0xd8000000 0xd8000000 0x01000000
 			  0xe0000000 0xe0000000 0x10000000>;
 
 		sdhci@b3000000 {
@@ -81,7 +95,7 @@ sdhci@b3000000 {
 
 		cf@b2800000 {
 			compatible = "arasan,cf-spear1340";
-			reg = <0xb2800000 0x100>;
+			reg = <0xb2800000 0x1000>;
 			interrupts = <0 29 0x4>;
 			status = "disabled";
 		};
@@ -113,6 +127,7 @@ fsmc: flash@b0000000 {
 				      0 23 0x4>;
 			st,ale-off = <0x20000>;
 			st,cle-off = <0x10000>;
+			st,mode = <2>;
 			status = "disabled";
 		};
 
@@ -125,6 +140,13 @@ gmac0: eth@e2000000 {
 			status = "disabled";
 		};
 
+		pcm {
+			compatible = "st,pcm-audio";
+			#address-cells = <0>;
+			#size-cells = <0>;
+			status = "disable";
+		};
+
 		smi: flash@ea000000 {
 			compatible = "st,spear600-smi";
 			#address-cells = <1>;
@@ -134,17 +156,11 @@ smi: flash@ea000000 {
 			status = "disabled";
 		};
 
-		spi0: spi@e0100000 {
-			compatible = "arm,pl022", "arm,primecell";
-			reg = <0xe0100000 0x1000>;
-			interrupts = <0 31 0x4>;
-			status = "disabled";
-		};
-
 		ehci@e4800000 {
 			compatible = "st,spear600-ehci", "usb-ehci";
 			reg = <0xe4800000 0x1000>;
 			interrupts = <0 64 0x4>;
+			usbh0_id = <0>;
 			status = "disabled";
 		};
 
@@ -152,6 +168,7 @@ ehci@e5800000 {
 			compatible = "st,spear600-ehci", "usb-ehci";
 			reg = <0xe5800000 0x1000>;
 			interrupts = <0 66 0x4>;
+			usbh1_id = <1>;
 			status = "disabled";
 		};
 
@@ -159,6 +176,7 @@ ohci@e4000000 {
 			compatible = "st,spear600-ohci", "usb-ohci";
 			reg = <0xe4000000 0x1000>;
 			interrupts = <0 65 0x4>;
+			usbh0_id = <0>;
 			status = "disabled";
 		};
 
@@ -166,6 +184,7 @@ ohci@e5000000 {
 			compatible = "st,spear600-ohci", "usb-ohci";
 			reg = <0xe5000000 0x1000>;
 			interrupts = <0 67 0x4>;
+			usbh1_id = <1>;
 			status = "disabled";
 		};
 
@@ -175,6 +194,8 @@ apb {
 			compatible = "simple-bus";
 			ranges = <0x50000000 0x50000000 0x10000000
 				  0xb0000000 0xb0000000 0x10000000
+				  0xd0000000 0xd0000000 0x02000000
+				  0xd8000000 0xd8000000 0x01000000
 				  0xe0000000 0xe0000000 0x10000000>;
 
 			gpio0: gpio@e0600000 {
@@ -215,8 +236,35 @@ i2c0: i2c@e0280000 {
 				status = "disabled";
 			};
 
+			i2s@e0180000 {
+				compatible = "st,designware-i2s";
+				reg = <0xe0180000 0x1000>;
+				interrupt-names = "play_irq", "record_irq";
+				interrupts = <0 10 0x4
+					      0 11 0x4 >;
+				status = "disabled";
+			};
+
+			i2s@e0200000 {
+				compatible = "st,designware-i2s";
+				reg = <0xe0200000 0x1000>;
+				interrupt-names = "play_irq", "record_irq";
+				interrupts = <0 26 0x4
+					      0 53 0x4>;
+				status = "disabled";
+			};
+
+			spi0: spi@e0100000 {
+				compatible = "arm,pl022", "arm,primecell";
+				reg = <0xe0100000 0x1000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <0 31 0x4>;
+				status = "disabled";
+			};
+
 			rtc@e0580000 {
-				compatible = "st,spear-rtc";
+				compatible = "st,spear600-rtc";
 				reg = <0xe0580000 0x1000>;
 				interrupts = <0 36 0x4>;
 				status = "disabled";
@@ -232,7 +280,7 @@ serial@e0000000 {
 			adc@e0080000 {
 				compatible = "st,spear600-adc";
 				reg = <0xe0080000 0x1000>;
-				interrupts = <0 44 0x4>;
+				interrupts = <0 12 0x4>;
 				status = "disabled";
 			};
 
@@ -245,7 +293,8 @@ timer@e0380000 {
 			timer@ec800600 {
 				compatible = "arm,cortex-a9-twd-timer";
 				reg = <0xec800600 0x20>;
-				interrupts = <1 13 0x301>;
+				interrupts = <1 13 0x4>;
+				status = "disabled";
 			};
 
 			wdt@ec800620 {
@@ -257,6 +306,7 @@ wdt@ec800620 {
 			thermal@e07008c4 {
 				compatible = "st,thermal-spear1340";
 				reg = <0xe07008c4 0x4>;
+				thermal_flags = <0x7000>;
 			};
 		};
 	};

arch/arm/boot/dts/spear300-evb.dts

@@ -100,15 +100,23 @@ partition@0 {
 				};
 				partition@10000 {
 					label = "u-boot";
-					reg = <0x10000 0x40000>;
+					reg = <0x10000 0x50000>;
 				};
-				partition@50000 {
+				partition@60000 {
+					label = "environment";
+					reg = <0x60000 0x10000>;
+				};
+				partition@70000 {
+					label = "dtb";
+					reg = <0x70000 0x10000>;
+				};
+				partition@80000 {
 					label = "linux";
-					reg = <0x50000 0x2c0000>;
+					reg = <0x80000 0x310000>;
 				};
-				partition@310000 {
+				partition@390000 {
 					label = "rootfs";
-					reg = <0x310000 0x4f0000>;
+					reg = <0x390000 0x0>;
 				};
 			};
 		};
@@ -235,6 +243,8 @@ rtc@fc900000 {
 
 			serial@d0000000 {
 			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
 			};
 
 			wdt@fc880000 {

arch/arm/boot/dts/spear300.dtsi

@@ -27,7 +27,7 @@ pinmux@99000000 {
 		};
 
 		clcd@60000000 {
-			compatible = "arm,clcd-pl110", "arm,primecell";
+			compatible = "arm,pl110", "arm,primecell";
 			reg = <0x60000000 0x1000>;
 			interrupts = <30>;
 			status = "disabled";
@@ -52,6 +52,14 @@ sdhci@70000000 {
 			status = "disabled";
 		};
 
+		shirq: interrupt-controller@0x50000000 {
+			compatible = "st,spear300-shirq";
+			reg = <0x50000000 0x1000>;
+			interrupts = <28>;
+			#interrupt-cells = <1>;
+			interrupt-controller;
+		};
+
 		apb {
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -64,12 +72,16 @@ gpio1: gpio@a9000000 {
 				compatible = "arm,pl061", "arm,primecell";
 				gpio-controller;
 				reg = <0xa9000000 0x1000>;
+				interrupts = <8>;
+				interrupt-parent = <&shirq>;
 				status = "disabled";
 			};
 
 			kbd@a0000000 {
 				compatible = "st,spear300-kbd";
 				reg = <0xa0000000 0x1000>;
+				interrupts = <7>;
+				interrupt-parent = <&shirq>;
 				status = "disabled";
 			};
 		};

arch/arm/boot/dts/spear310-evb.dts

@@ -114,15 +114,23 @@ partition@0 {
 				};
 				partition@10000 {
 					label = "u-boot";
-					reg = <0x10000 0x40000>;
+					reg = <0x10000 0x50000>;
 				};
-				partition@50000 {
+				partition@60000 {
+					label = "environment";
+					reg = <0x60000 0x10000>;
+				};
+				partition@70000 {
+					label = "dtb";
+					reg = <0x70000 0x10000>;
+				};
+				partition@80000 {
 					label = "linux";
-					reg = <0x50000 0x2c0000>;
+					reg = <0x80000 0x310000>;
 				};
-				partition@310000 {
+				partition@390000 {
 					label = "rootfs";
-					reg = <0x310000 0x4f0000>;
+					reg = <0x390000 0x0>;
 				};
 			};
 		};
@@ -158,26 +166,38 @@ rtc@fc900000 {
 
 			serial@d0000000 {
 			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
 			};
 
 			serial@b2000000 {
 			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
 			};
 
 			serial@b2080000 {
 			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
 			};
 
 			serial@b2100000 {
 			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
 			};
 
 			serial@b2180000 {
 			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
 			};
 
 			serial@b2200000 {
 			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
 			};
 
 			wdt@fc880000 {

arch/arm/boot/dts/spear310.dtsi

@@ -40,6 +40,14 @@ fsmc: flash@44000000 {
 			status = "disabled";
 		};
 
+		shirq: interrupt-controller@0xb4000000 {
+			compatible = "st,spear310-shirq";
+			reg = <0xb4000000 0x1000>;
+			interrupts = <28 29 30 1>;
+			#interrupt-cells = <1>;
+			interrupt-controller;
+		};
+
 		apb {
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -50,30 +58,40 @@ apb {
 			serial@b2000000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0xb2000000 0x1000>;
+				interrupts = <8>;
+				interrupt-parent = <&shirq>;
 				status = "disabled";
 			};
 
 			serial@b2080000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0xb2080000 0x1000>;
+				interrupts = <9>;
+				interrupt-parent = <&shirq>;
 				status = "disabled";
 			};
 
 			serial@b2100000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0xb2100000 0x1000>;
+				interrupts = <10>;
+				interrupt-parent = <&shirq>;
 				status = "disabled";
 			};
 
 			serial@b2180000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0xb2180000 0x1000>;
+				interrupts = <11>;
+				interrupt-parent = <&shirq>;
 				status = "disabled";
 			};
 
 			serial@b2200000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0xb2200000 0x1000>;
+				interrupts = <12>;
+				interrupt-parent = <&shirq>;
 				status = "disabled";
 			};
 

arch/arm/boot/dts/spear320-evb.dts

@@ -76,20 +76,12 @@ mii2 {
 					st,function = "mii2";
 				};
 				pwm0_1 {
-					st,pins = "pwm0_1_pin_14_15_grp";
+					st,pins = "pwm0_1_pin_37_38_grp";
 					st,function = "pwm0_1";
 				};
-				pwm2 {
-					st,pins = "pwm2_pin_13_grp";
-					st,function = "pwm2";
-				};
 			};
 		};
 
-		clcd@90000000 {
-			status = "okay";
-		};
-
 		dma@fc400000 {
 			status = "okay";
 		};
@@ -103,6 +95,7 @@ gmac: eth@e0800000 {
 		};
 
 		sdhci@70000000 {
+			power-gpio = <&gpiopinctrl 61 1>;
 			status = "okay";
 		};
 
@@ -122,15 +115,23 @@ partition@0 {
 				};
 				partition@10000 {
 					label = "u-boot";
-					reg = <0x10000 0x40000>;
+					reg = <0x10000 0x50000>;
+				};
+				partition@60000 {
+					label = "environment";
+					reg = <0x60000 0x10000>;
 				};
-				partition@50000 {
+				partition@70000 {
+					label = "dtb";
+					reg = <0x70000 0x10000>;
+				};
+				partition@80000 {
 					label = "linux";
-					reg = <0x50000 0x2c0000>;
+					reg = <0x80000 0x310000>;
 				};
-				partition@310000 {
+				partition@390000 {
 					label = "rootfs";
-					reg = <0x310000 0x4f0000>;
+					reg = <0x390000 0x0>;
 				};
 			};
 		};
@@ -182,14 +183,20 @@ rtc@fc900000 {
 
 			serial@d0000000 {
 			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
 			};
 
 			serial@a3000000 {
 			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
 			};
 
 			serial@a4000000 {
 			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
 			};
 
 			wdt@fc880000 {

arch/arm/boot/dts/spear320-hmi.dts

+/*
+ * DTS file for SPEAr320 Evaluation Baord
+ *
+ * Copyright 2012 Shiraz Hashim <shiraz.hashim@st.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "spear320.dtsi"
+
+/ {
+	model = "ST SPEAr320 HMI Board";
+	compatible = "st,spear320-hmi", "st,spear320";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory {
+		reg = <0 0x40000000>;
+	};
+
+	ahb {
+		pinmux@b3000000 {
+			st,pinmux-mode = <4>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&state_default>;
+
+			state_default: pinmux {
+				i2c0 {
+					st,pins = "i2c0_grp";
+					st,function = "i2c0";
+				};
+				ssp0 {
+					st,pins = "ssp0_grp";
+					st,function = "ssp0";
+				};
+				uart0 {
+					st,pins = "uart0_grp";
+					st,function = "uart0";
+				};
+				clcd {
+					st,pins = "clcd_grp";
+					st,function = "clcd";
+				};
+				fsmc {
+					st,pins = "fsmc_8bit_grp";
+					st,function = "fsmc";
+				};
+				sdhci {
+					st,pins = "sdhci_cd_12_grp";
+					st,function = "sdhci";
+				};
+				i2s {
+					st,pins = "i2s_grp";
+					st,function = "i2s";
+				};
+				uart1 {
+					st,pins = "uart1_grp";
+					st,function = "uart1";
+				};
+				uart2 {
+					st,pins = "uart2_grp";
+					st,function = "uart2";
+				};
+				can0 {
+					st,pins = "can0_grp";
+					st,function = "can0";
+				};
+				can1 {
+					st,pins = "can1_grp";
+					st,function = "can1";
+				};
+				mii0_1 {
+					st,pins = "rmii0_1_grp";
+					st,function = "mii0_1";
+				};
+				pwm0_1 {
+					st,pins = "pwm0_1_pin_37_38_grp";
+					st,function = "pwm0_1";
+				};
+				pwm2 {
+					st,pins = "pwm2_pin_34_grp";
+					st,function = "pwm2";
+				};
+			};
+		};
+
+		clcd@90000000 {
+			status = "okay";
+		};
+
+		dma@fc400000 {
+			status = "okay";
+		};
+
+		ehci@e1800000 {
+			status = "okay";
+		};
+
+		fsmc: flash@4c000000 {
+			status = "okay";
+
+			partition@0 {
+				label = "xloader";
+				reg = <0x0 0x80000>;
+			};
+			partition@80000 {
+				label = "u-boot";
+				reg = <0x80000 0x140000>;
+			};
+			partition@1C0000 {
+				label = "environment";
+				reg = <0x1C0000 0x40000>;
+			};
+			partition@200000 {
+				label = "dtb";
+				reg = <0x200000 0x40000>;
+			};
+			partition@240000 {
+				label = "linux";
+				reg = <0x240000 0xC00000>;
+			};
+			partition@E40000 {
+				label = "rootfs";
+				reg = <0xE40000 0x0>;
+			};
+		};
+
+		gpio_keys {
+			compatible = "gpio-keys";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			button@1 {
+				label = "user button 1";
+				linux,code = <0x100>;
+				gpios = <&stmpegpio 3 0x4>;
+				debounce-interval = <20>;
+				gpio-key,wakeup = <1>;
+			};
+
+			button@2 {
+				label = "user button 2";
+				linux,code = <0x200>;
+				gpios = <&stmpegpio 2 0x4>;
+				debounce-interval = <20>;
+				gpio-key,wakeup = <1>;
+			};
+		};
+
+		ohci@e1900000 {
+			status = "okay";
+		};
+
+		ohci@e2100000 {
+			status = "okay";
+		};
+
+		pwm: pwm@a8000000 {
+			status = "okay";
+		};
+
+		sdhci@70000000 {
+			power-gpio = <&gpiopinctrl 50 1>;
+			power_always_enb;
+			status = "okay";
+		};
+
+		smi: flash@fc000000 {
+			status = "okay";
+			clock-rate=<50000000>;
+
+			flash@f8000000 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xf8000000 0x800000>;
+				st,smi-fast-mode;
+
+				partition@0 {
+					label = "xloader";
+					reg = <0x0 0x10000>;
+				};
+				partition@10000 {
+					label = "u-boot";
+					reg = <0x10000 0x50000>;
+				};
+				partition@60000 {
+					label = "environment";
+					reg = <0x60000 0x10000>;
+				};
+				partition@70000 {
+					label = "dtb";
+					reg = <0x70000 0x10000>;
+				};
+				partition@80000 {
+					label = "linux";
+					reg = <0x80000 0x310000>;
+				};
+				partition@390000 {
+					label = "rootfs";
+					reg = <0x390000 0x0>;
+				};
+			};
+		};
+
+		spi0: spi@d0100000 {
+			status = "okay";
+		};
+
+		spi1: spi@a5000000 {
+			status = "okay";
+		};
+
+		spi2: spi@a6000000 {
+			status = "okay";
+		};
+
+		usbd@e1100000 {
+			status = "okay";
+		};
+
+		apb {
+			gpio0: gpio@fc980000 {
+			       status = "okay";
+			};
+
+			gpio@b3000000 {
+				status = "okay";
+			};
+
+			i2c0: i2c@d0180000 {
+				status = "okay";
+
+				stmpe811@41 {
+					compatible = "st,stmpe811";
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x41>;
+					irq-over-gpio;
+					irq-gpios = <&gpiopinctrl 29 0x4>;
+					id = <0>;
+					blocks = <0x5>;
+					irq-trigger = <0x1>;
+
+					stmpegpio: stmpe-gpio {
+						compatible = "stmpe,gpio";
+						reg = <0>;
+						gpio-controller;
+						#gpio-cells = <2>;
+						gpio,norequest-mask = <0xF3>;
+					};
+
+					stmpe610-ts {
+						compatible = "stmpe,ts";
+						reg = <0>;
+						ts,sample-time = <4>;
+						ts,mod-12b = <1>;
+						ts,ref-sel = <0>;
+						ts,adc-freq = <1>;
+						ts,ave-ctrl = <1>;
+						ts,touch-det-delay = <3>;
+						ts,settling = <4>;
+						ts,fraction-z = <7>;
+						ts,i-drive = <1>;
+					};
+				};
+			};
+
+			i2c1: i2c@a7000000 {
+			       status = "okay";
+			};
+
+			rtc@fc900000 {
+			       status = "okay";
+			};
+
+			serial@d0000000 {
+			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
+			};
+
+			serial@a3000000 {
+			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
+			};
+
+			serial@a4000000 {
+			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
+			};
+
+			wdt@fc880000 {
+			       status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/spear320.dtsi

@@ -28,9 +28,10 @@ pinmux: pinmux@b3000000 {
 		};
 
 		clcd@90000000 {
-			compatible = "arm,clcd-pl110", "arm,primecell";
+			compatible = "arm,pl110", "arm,primecell";
 			reg = <0x90000000 0x1000>;
-			interrupts = <33>;
+			interrupts = <8>;
+			interrupt-parent = <&shirq>;
 			status = "disabled";
 		};
 
@@ -49,19 +50,43 @@ fsmc: flash@4c000000 {
 		sdhci@70000000 {
 			compatible = "st,sdhci-spear";
 			reg = <0x70000000 0x100>;
-			interrupts = <29>;
+			interrupts = <10>;
+			interrupt-parent = <&shirq>;
 			status = "disabled";
 		};
 
+		shirq: interrupt-controller@0xb3000000 {
+			compatible = "st,spear320-shirq";
+			reg = <0xb3000000 0x1000>;
+			interrupts = <30 28 29 1>;
+			#interrupt-cells = <1>;
+			interrupt-controller;
+		};
+
 		spi1: spi@a5000000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0xa5000000 0x1000>;
+			interrupts = <15>;
+			interrupt-parent = <&shirq>;
+			#address-cells = <1>;
+			#size-cells = <0>;
 			status = "disabled";
 		};
 
 		spi2: spi@a6000000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0xa6000000 0x1000>;
+			interrupts = <16>;
+			interrupt-parent = <&shirq>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		pwm: pwm@a8000000 {
+			compatible ="st,spear-pwm";
+			reg = <0xa8000000 0x1000>;
+			#pwm-cells = <2>;
 			status = "disabled";
                 };
 
@@ -69,7 +94,7 @@ apb {
 			#address-cells = <1>;
 			#size-cells = <1>;
 			compatible = "simple-bus";
-			ranges = <0xa0000000 0xa0000000 0x10000000
+			ranges = <0xa0000000 0xa0000000 0x20000000
 				  0xd0000000 0xd0000000 0x30000000>;
 
 			i2c1: i2c@a7000000 {
@@ -77,18 +102,24 @@ i2c1: i2c@a7000000 {
 				#size-cells = <0>;
 				compatible = "snps,designware-i2c";
 				reg = <0xa7000000 0x1000>;
+				interrupts = <21>;
+				interrupt-parent = <&shirq>;
 				status = "disabled";
 			};
 
 			serial@a3000000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0xa3000000 0x1000>;
+				interrupts = <13>;
+				interrupt-parent = <&shirq>;
 				status = "disabled";
 			};
 
 			serial@a4000000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0xa4000000 0x1000>;
+				interrupts = <14>;
+				interrupt-parent = <&shirq>;
 				status = "disabled";
 			};
 

arch/arm/boot/dts/spear3xx.dtsi

@@ -53,6 +53,7 @@ gmac: eth@e0800000 {
 			reg = <0xe0800000 0x8000>;
 			interrupts = <23 22>;
 			interrupt-names = "macirq", "eth_wake_irq";
+			phy-mode = "mii";
 			status = "disabled";
 		};
 
@@ -69,6 +70,8 @@ spi0: spi@d0100000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0xd0100000 0x1000>;
 			interrupts = <20>;
+			#address-cells = <1>;
+			#size-cells = <0>;
 			status = "disabled";
 		};
 
@@ -120,7 +123,7 @@ i2c0: i2c@d0180000 {
 			};
 
 			rtc@fc900000 {
-				compatible = "st,spear-rtc";
+				compatible = "st,spear600-rtc";
 				reg = <0xfc900000 0x1000>;
 				interrupts = <10>;
 				status = "disabled";

arch/arm/boot/dts/spear600-evb.dts

@@ -24,15 +24,35 @@ memory {
 	};
 
 	ahb {
+		clcd@fc200000 {
+			status = "okay";
+		};
+
 		dma@fc400000 {
 			status = "okay";
 		};
 
+		ehci@e1800000 {
+			status = "okay";
+		};
+
+		ehci@e2000000 {
+			status = "okay";
+		};
+
 		gmac: ethernet@e0800000 {
 			phy-mode = "gmii";
 			status = "okay";
 		};
 
+		ohci@e1900000 {
+			status = "okay";
+		};
+
+		ohci@e2100000 {
+			status = "okay";
+		};
+
 		smi: flash@fc000000 {
 			status = "okay";
 			clock-rate=<50000000>;
@@ -49,15 +69,23 @@ partition@0 {
 				};
 				partition@10000 {
 					label = "u-boot";
-					reg = <0x10000 0x40000>;
+					reg = <0x10000 0x50000>;
 				};
-				partition@50000 {
+				partition@60000 {
+					label = "environment";
+					reg = <0x60000 0x10000>;
+				};
+				partition@70000 {
+					label = "dtb";
+					reg = <0x70000 0x10000>;
+				};
+				partition@80000 {
 					label = "linux";
-					reg = <0x50000 0x2c0000>;
+					reg = <0x80000 0x310000>;
 				};
-				partition@310000 {
+				partition@390000 {
 					label = "rootfs";
-					reg = <0x310000 0x4f0000>;
+					reg = <0x390000 0x0>;
 				};
 			};
 		};
@@ -65,10 +93,18 @@ partition@310000 {
 		apb {
 			serial@d0000000 {
 				status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
 			};
 
 			serial@d0080000 {
 				status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
+			};
+
+			rtc@fc900000 {
+			       status = "okay";
 			};
 
 			i2c@d0200000 {

arch/arm/boot/dts/spear600.dtsi

@@ -45,6 +45,14 @@ vic1: interrupt-controller@f1000000 {
 			#interrupt-cells = <1>;
 		};
 
+		clcd@fc200000 {
+			compatible = "arm,pl110", "arm,primecell";
+			reg = <0xfc200000 0x1000>;
+			interrupt-parent = <&vic1>;
+			interrupts = <12>;
+			status = "disabled";
+		};
+
 		dma@fc400000 {
 			compatible = "arm,pl080", "arm,primecell";
 			reg = <0xfc400000 0x1000>;
@@ -59,6 +67,7 @@ gmac: ethernet@e0800000 {
 			interrupt-parent = <&vic1>;
 			interrupts = <24 23>;
 			interrupt-names = "macirq", "eth_wake_irq";
+			phy-mode = "gmii";
 			status = "disabled";
 		};
 
@@ -178,6 +187,13 @@ i2c@d0200000 {
 				status = "disabled";
 			};
 
+			rtc@fc900000 {
+				compatible = "st,spear600-rtc";
+				reg = <0xfc900000 0x1000>;
+				interrupts = <10>;
+				status = "disabled";
+			};
+
 			timer@f0000000 {
 				compatible = "st,spear-timer";
 				reg = <0xf0000000 0x400>;

arch/arm/mach-spear13xx/include/mach/spear.h

@@ -47,14 +47,6 @@
 #define DMAC1_BASE				UL(0xEB000000)
 #define MCIF_CF_BASE				UL(0xB2800000)
 
-/* Devices present in SPEAr1310 */
-#ifdef CONFIG_MACH_SPEAR1310
-#define SPEAR1310_RAS_GRP1_BASE			UL(0xD8000000)
-#define VA_SPEAR1310_RAS_GRP1_BASE		UL(0xFA000000)
-#define SPEAR1310_RAS_BASE			UL(0xD8400000)
-#define VA_SPEAR1310_RAS_BASE			IOMEM(UL(0xFA400000))
-#endif /* CONFIG_MACH_SPEAR1310 */
-
 /* Debug uart for linux, will be used for debug and uncompress messages */
 #define SPEAR_DBG_UART_BASE			UART_BASE
 #define VA_SPEAR_DBG_UART_BASE			VA_UART_BASE

arch/arm/mach-spear13xx/spear1310.c

@@ -15,6 +15,7 @@
 
 #include <linux/amba/pl022.h>
 #include <linux/of_platform.h>
+#include <linux/pata_arasan_cf_data.h>
 #include <asm/hardware/gic.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
@@ -27,16 +28,25 @@
 #define SPEAR1310_SATA1_BASE			UL(0xB1800000)
 #define SPEAR1310_SATA2_BASE			UL(0xB4000000)
 
+#define SPEAR1310_RAS_GRP1_BASE			UL(0xD8000000)
+#define VA_SPEAR1310_RAS_GRP1_BASE		UL(0xFA000000)
+#define SPEAR1310_RAS_BASE			UL(0xD8400000)
+#define VA_SPEAR1310_RAS_BASE			IOMEM(UL(0xFA400000))
+
+static struct arasan_cf_pdata cf_pdata = {
+	.cf_if_clk = CF_IF_CLK_166M,
+	.quirk = CF_BROKEN_UDMA,
+	.dma_priv = &cf_dma_priv,
+};
+
 /* ssp device registration */
 static struct pl022_ssp_controller ssp1_plat_data = {
-	.bus_id = 0,
 	.enable_dma = 0,
-	.num_chipselect = 3,
 };
 
 /* Add SPEAr1310 auxdata to pass platform data */
 static struct of_dev_auxdata spear1310_auxdata_lookup[] __initdata = {
-	OF_DEV_AUXDATA("arasan,cf-spear1340", MCIF_CF_BASE, NULL, &cf_dma_priv),
+	OF_DEV_AUXDATA("arasan,cf-spear1340", MCIF_CF_BASE, NULL, &cf_pdata),
 	OF_DEV_AUXDATA("snps,dma-spear1340", DMAC0_BASE, NULL, &dmac_plat_data),
 	OF_DEV_AUXDATA("snps,dma-spear1340", DMAC1_BASE, NULL, &dmac_plat_data),
 	OF_DEV_AUXDATA("arm,pl022", SSP_BASE, NULL, &pl022_plat_data),

arch/arm/mach-spear13xx/spear13xx.c

@@ -57,12 +57,10 @@ static struct dw_dma_slave ssp_dma_param[] = {
 };
 
 struct pl022_ssp_controller pl022_plat_data = {
-	.bus_id = 0,
 	.enable_dma = 1,
 	.dma_filter = dw_dma_filter,
 	.dma_rx_param = &ssp_dma_param[1],
 	.dma_tx_param = &ssp_dma_param[0],
-	.num_chipselect = 3,
 };
 
 /* CF device registration */

arch/arm/mach-spear3xx/include/mach/irqs.h

@@ -14,14 +14,6 @@
 #ifndef __MACH_IRQS_H
 #define __MACH_IRQS_H
 
-/* FIXME: probe all these from DT */
-#define SPEAR3XX_IRQ_INTRCOMM_RAS_ARM		1
-#define SPEAR3XX_IRQ_GEN_RAS_1			28
-#define SPEAR3XX_IRQ_GEN_RAS_2			29
-#define SPEAR3XX_IRQ_GEN_RAS_3			30
-#define SPEAR3XX_IRQ_VIC_END			32
-#define SPEAR3XX_VIRQ_START			SPEAR3XX_IRQ_VIC_END
-
-#define NR_IRQS			160
+#define NR_IRQS			256
 
 #endif /* __MACH_IRQS_H */

arch/arm/mach-spear3xx/spear300.c

@@ -17,102 +17,9 @@
 #include <linux/of_platform.h>
 #include <asm/hardware/vic.h>
 #include <asm/mach/arch.h>
-#include <plat/shirq.h>
 #include <mach/generic.h>
 #include <mach/spear.h>
 
-/* Base address of various IPs */
-#define SPEAR300_TELECOM_BASE		UL(0x50000000)
-
-/* Interrupt registers offsets and masks */
-#define SPEAR300_INT_ENB_MASK_REG	0x54
-#define SPEAR300_INT_STS_MASK_REG	0x58
-#define SPEAR300_IT_PERS_S_IRQ_MASK	(1 << 0)
-#define SPEAR300_IT_CHANGE_S_IRQ_MASK	(1 << 1)
-#define SPEAR300_I2S_IRQ_MASK		(1 << 2)
-#define SPEAR300_TDM_IRQ_MASK		(1 << 3)
-#define SPEAR300_CAMERA_L_IRQ_MASK	(1 << 4)
-#define SPEAR300_CAMERA_F_IRQ_MASK	(1 << 5)
-#define SPEAR300_CAMERA_V_IRQ_MASK	(1 << 6)
-#define SPEAR300_KEYBOARD_IRQ_MASK	(1 << 7)
-#define SPEAR300_GPIO1_IRQ_MASK		(1 << 8)
-
-#define SPEAR300_SHIRQ_RAS1_MASK	0x1FF
-
-#define SPEAR300_SOC_CONFIG_BASE	UL(0x99000000)
-
-
-/* SPEAr300 Virtual irq definitions */
-/* IRQs sharing IRQ_GEN_RAS_1 */
-#define SPEAR300_VIRQ_IT_PERS_S			(SPEAR3XX_VIRQ_START + 0)
-#define SPEAR300_VIRQ_IT_CHANGE_S		(SPEAR3XX_VIRQ_START + 1)
-#define SPEAR300_VIRQ_I2S			(SPEAR3XX_VIRQ_START + 2)
-#define SPEAR300_VIRQ_TDM			(SPEAR3XX_VIRQ_START + 3)
-#define SPEAR300_VIRQ_CAMERA_L			(SPEAR3XX_VIRQ_START + 4)
-#define SPEAR300_VIRQ_CAMERA_F			(SPEAR3XX_VIRQ_START + 5)
-#define SPEAR300_VIRQ_CAMERA_V			(SPEAR3XX_VIRQ_START + 6)
-#define SPEAR300_VIRQ_KEYBOARD			(SPEAR3XX_VIRQ_START + 7)
-#define SPEAR300_VIRQ_GPIO1			(SPEAR3XX_VIRQ_START + 8)
-
-/* IRQs sharing IRQ_GEN_RAS_3 */
-#define SPEAR300_IRQ_CLCD			SPEAR3XX_IRQ_GEN_RAS_3
-
-/* IRQs sharing IRQ_INTRCOMM_RAS_ARM */
-#define SPEAR300_IRQ_SDHCI			SPEAR3XX_IRQ_INTRCOMM_RAS_ARM
-
-/* spear3xx shared irq */
-static struct shirq_dev_config shirq_ras1_config[] = {
-	{
-		.virq = SPEAR300_VIRQ_IT_PERS_S,
-		.enb_mask = SPEAR300_IT_PERS_S_IRQ_MASK,
-		.status_mask = SPEAR300_IT_PERS_S_IRQ_MASK,
-	}, {
-		.virq = SPEAR300_VIRQ_IT_CHANGE_S,
-		.enb_mask = SPEAR300_IT_CHANGE_S_IRQ_MASK,
-		.status_mask = SPEAR300_IT_CHANGE_S_IRQ_MASK,
-	}, {
-		.virq = SPEAR300_VIRQ_I2S,
-		.enb_mask = SPEAR300_I2S_IRQ_MASK,
-		.status_mask = SPEAR300_I2S_IRQ_MASK,
-	}, {
-		.virq = SPEAR300_VIRQ_TDM,
-		.enb_mask = SPEAR300_TDM_IRQ_MASK,
-		.status_mask = SPEAR300_TDM_IRQ_MASK,
-	}, {
-		.virq = SPEAR300_VIRQ_CAMERA_L,
-		.enb_mask = SPEAR300_CAMERA_L_IRQ_MASK,
-		.status_mask = SPEAR300_CAMERA_L_IRQ_MASK,
-	}, {
-		.virq = SPEAR300_VIRQ_CAMERA_F,
-		.enb_mask = SPEAR300_CAMERA_F_IRQ_MASK,
-		.status_mask = SPEAR300_CAMERA_F_IRQ_MASK,
-	}, {
-		.virq = SPEAR300_VIRQ_CAMERA_V,
-		.enb_mask = SPEAR300_CAMERA_V_IRQ_MASK,
-		.status_mask = SPEAR300_CAMERA_V_IRQ_MASK,
-	}, {
-		.virq = SPEAR300_VIRQ_KEYBOARD,
-		.enb_mask = SPEAR300_KEYBOARD_IRQ_MASK,
-		.status_mask = SPEAR300_KEYBOARD_IRQ_MASK,
-	}, {
-		.virq = SPEAR300_VIRQ_GPIO1,
-		.enb_mask = SPEAR300_GPIO1_IRQ_MASK,
-		.status_mask = SPEAR300_GPIO1_IRQ_MASK,
-	},
-};
-
-static struct spear_shirq shirq_ras1 = {
-	.irq = SPEAR3XX_IRQ_GEN_RAS_1,
-	.dev_config = shirq_ras1_config,
-	.dev_count = ARRAY_SIZE(shirq_ras1_config),
-	.regs = {
-		.enb_reg = SPEAR300_INT_ENB_MASK_REG,
-		.status_reg = SPEAR300_INT_STS_MASK_REG,
-		.status_reg_mask = SPEAR300_SHIRQ_RAS1_MASK,
-		.clear_reg = -1,
-	},
-};
-
 /* DMAC platform data's slave info */
 struct pl08x_channel_data spear300_dma_info[] = {
 	{
@@ -285,21 +192,11 @@ static struct of_dev_auxdata spear300_auxdata_lookup[] __initdata = {
 
 static void __init spear300_dt_init(void)
 {
-	int ret;
-
 	pl080_plat_data.slave_channels = spear300_dma_info;
 	pl080_plat_data.num_slave_channels = ARRAY_SIZE(spear300_dma_info);
 
 	of_platform_populate(NULL, of_default_bus_match_table,
 			spear300_auxdata_lookup, NULL);
-
-	/* shared irq registration */
-	shirq_ras1.regs.base = ioremap(SPEAR300_TELECOM_BASE, SZ_4K);
-	if (shirq_ras1.regs.base) {
-		ret = spear_shirq_register(&shirq_ras1);
-		if (ret)
-			pr_err("Error registering Shared IRQ\n");
-	}
 }
 
 static const char * const spear300_dt_board_compat[] = {

arch/arm/mach-spear3xx/spear310.c

@@ -18,7 +18,6 @@
 #include <linux/of_platform.h>
 #include <asm/hardware/vic.h>
 #include <asm/mach/arch.h>
-#include <plat/shirq.h>
 #include <mach/generic.h>
 #include <mach/spear.h>
 
@@ -27,176 +26,6 @@
 #define SPEAR310_UART3_BASE		UL(0xB2100000)
 #define SPEAR310_UART4_BASE		UL(0xB2180000)
 #define SPEAR310_UART5_BASE		UL(0xB2200000)
-#define SPEAR310_SOC_CONFIG_BASE	UL(0xB4000000)
-
-/* Interrupt registers offsets and masks */
-#define SPEAR310_INT_STS_MASK_REG	0x04
-#define SPEAR310_SMII0_IRQ_MASK		(1 << 0)
-#define SPEAR310_SMII1_IRQ_MASK		(1 << 1)
-#define SPEAR310_SMII2_IRQ_MASK		(1 << 2)
-#define SPEAR310_SMII3_IRQ_MASK		(1 << 3)
-#define SPEAR310_WAKEUP_SMII0_IRQ_MASK	(1 << 4)
-#define SPEAR310_WAKEUP_SMII1_IRQ_MASK	(1 << 5)
-#define SPEAR310_WAKEUP_SMII2_IRQ_MASK	(1 << 6)
-#define SPEAR310_WAKEUP_SMII3_IRQ_MASK	(1 << 7)
-#define SPEAR310_UART1_IRQ_MASK		(1 << 8)
-#define SPEAR310_UART2_IRQ_MASK		(1 << 9)
-#define SPEAR310_UART3_IRQ_MASK		(1 << 10)
-#define SPEAR310_UART4_IRQ_MASK		(1 << 11)
-#define SPEAR310_UART5_IRQ_MASK		(1 << 12)
-#define SPEAR310_EMI_IRQ_MASK		(1 << 13)
-#define SPEAR310_TDM_HDLC_IRQ_MASK	(1 << 14)
-#define SPEAR310_RS485_0_IRQ_MASK	(1 << 15)
-#define SPEAR310_RS485_1_IRQ_MASK	(1 << 16)
-
-#define SPEAR310_SHIRQ_RAS1_MASK	0x000FF
-#define SPEAR310_SHIRQ_RAS2_MASK	0x01F00
-#define SPEAR310_SHIRQ_RAS3_MASK	0x02000
-#define SPEAR310_SHIRQ_INTRCOMM_RAS_MASK	0x1C000
-
-/* SPEAr310 Virtual irq definitions */
-/* IRQs sharing IRQ_GEN_RAS_1 */
-#define SPEAR310_VIRQ_SMII0			(SPEAR3XX_VIRQ_START + 0)
-#define SPEAR310_VIRQ_SMII1			(SPEAR3XX_VIRQ_START + 1)
-#define SPEAR310_VIRQ_SMII2			(SPEAR3XX_VIRQ_START + 2)
-#define SPEAR310_VIRQ_SMII3			(SPEAR3XX_VIRQ_START + 3)
-#define SPEAR310_VIRQ_WAKEUP_SMII0		(SPEAR3XX_VIRQ_START + 4)
-#define SPEAR310_VIRQ_WAKEUP_SMII1		(SPEAR3XX_VIRQ_START + 5)
-#define SPEAR310_VIRQ_WAKEUP_SMII2		(SPEAR3XX_VIRQ_START + 6)
-#define SPEAR310_VIRQ_WAKEUP_SMII3		(SPEAR3XX_VIRQ_START + 7)
-
-/* IRQs sharing IRQ_GEN_RAS_2 */
-#define SPEAR310_VIRQ_UART1			(SPEAR3XX_VIRQ_START + 8)
-#define SPEAR310_VIRQ_UART2			(SPEAR3XX_VIRQ_START + 9)
-#define SPEAR310_VIRQ_UART3			(SPEAR3XX_VIRQ_START + 10)
-#define SPEAR310_VIRQ_UART4			(SPEAR3XX_VIRQ_START + 11)
-#define SPEAR310_VIRQ_UART5			(SPEAR3XX_VIRQ_START + 12)
-
-/* IRQs sharing IRQ_GEN_RAS_3 */
-#define SPEAR310_VIRQ_EMI			(SPEAR3XX_VIRQ_START + 13)
-#define SPEAR310_VIRQ_PLGPIO			(SPEAR3XX_VIRQ_START + 14)
-
-/* IRQs sharing IRQ_INTRCOMM_RAS_ARM */
-#define SPEAR310_VIRQ_TDM_HDLC			(SPEAR3XX_VIRQ_START + 15)
-#define SPEAR310_VIRQ_RS485_0			(SPEAR3XX_VIRQ_START + 16)
-#define SPEAR310_VIRQ_RS485_1			(SPEAR3XX_VIRQ_START + 17)
-
-
-/* spear3xx shared irq */
-static struct shirq_dev_config shirq_ras1_config[] = {
-	{
-		.virq = SPEAR310_VIRQ_SMII0,
-		.status_mask = SPEAR310_SMII0_IRQ_MASK,
-	}, {
-		.virq = SPEAR310_VIRQ_SMII1,
-		.status_mask = SPEAR310_SMII1_IRQ_MASK,
-	}, {
-		.virq = SPEAR310_VIRQ_SMII2,
-		.status_mask = SPEAR310_SMII2_IRQ_MASK,
-	}, {
-		.virq = SPEAR310_VIRQ_SMII3,
-		.status_mask = SPEAR310_SMII3_IRQ_MASK,
-	}, {
-		.virq = SPEAR310_VIRQ_WAKEUP_SMII0,
-		.status_mask = SPEAR310_WAKEUP_SMII0_IRQ_MASK,
-	}, {
-		.virq = SPEAR310_VIRQ_WAKEUP_SMII1,
-		.status_mask = SPEAR310_WAKEUP_SMII1_IRQ_MASK,
-	}, {
-		.virq = SPEAR310_VIRQ_WAKEUP_SMII2,
-		.status_mask = SPEAR310_WAKEUP_SMII2_IRQ_MASK,
-	}, {
-		.virq = SPEAR310_VIRQ_WAKEUP_SMII3,
-		.status_mask = SPEAR310_WAKEUP_SMII3_IRQ_MASK,
-	},
-};
-
-static struct spear_shirq shirq_ras1 = {
-	.irq = SPEAR3XX_IRQ_GEN_RAS_1,
-	.dev_config = shirq_ras1_config,
-	.dev_count = ARRAY_SIZE(shirq_ras1_config),
-	.regs = {
-		.enb_reg = -1,
-		.status_reg = SPEAR310_INT_STS_MASK_REG,
-		.status_reg_mask = SPEAR310_SHIRQ_RAS1_MASK,
-		.clear_reg = -1,
-	},
-};
-
-static struct shirq_dev_config shirq_ras2_config[] = {
-	{
-		.virq = SPEAR310_VIRQ_UART1,
-		.status_mask = SPEAR310_UART1_IRQ_MASK,
-	}, {
-		.virq = SPEAR310_VIRQ_UART2,
-		.status_mask = SPEAR310_UART2_IRQ_MASK,
-	}, {
-		.virq = SPEAR310_VIRQ_UART3,
-		.status_mask = SPEAR310_UART3_IRQ_MASK,
-	}, {
-		.virq = SPEAR310_VIRQ_UART4,
-		.status_mask = SPEAR310_UART4_IRQ_MASK,
-	}, {
-		.virq = SPEAR310_VIRQ_UART5,
-		.status_mask = SPEAR310_UART5_IRQ_MASK,
-	},
-};
-
-static struct spear_shirq shirq_ras2 = {
-	.irq = SPEAR3XX_IRQ_GEN_RAS_2,
-	.dev_config = shirq_ras2_config,
-	.dev_count = ARRAY_SIZE(shirq_ras2_config),
-	.regs = {
-		.enb_reg = -1,
-		.status_reg = SPEAR310_INT_STS_MASK_REG,
-		.status_reg_mask = SPEAR310_SHIRQ_RAS2_MASK,
-		.clear_reg = -1,
-	},
-};
-
-static struct shirq_dev_config shirq_ras3_config[] = {
-	{
-		.virq = SPEAR310_VIRQ_EMI,
-		.status_mask = SPEAR310_EMI_IRQ_MASK,
-	},
-};
-
-static struct spear_shirq shirq_ras3 = {
-	.irq = SPEAR3XX_IRQ_GEN_RAS_3,
-	.dev_config = shirq_ras3_config,
-	.dev_count = ARRAY_SIZE(shirq_ras3_config),
-	.regs = {
-		.enb_reg = -1,
-		.status_reg = SPEAR310_INT_STS_MASK_REG,
-		.status_reg_mask = SPEAR310_SHIRQ_RAS3_MASK,
-		.clear_reg = -1,
-	},
-};
-
-static struct shirq_dev_config shirq_intrcomm_ras_config[] = {
-	{
-		.virq = SPEAR310_VIRQ_TDM_HDLC,
-		.status_mask = SPEAR310_TDM_HDLC_IRQ_MASK,
-	}, {
-		.virq = SPEAR310_VIRQ_RS485_0,
-		.status_mask = SPEAR310_RS485_0_IRQ_MASK,
-	}, {
-		.virq = SPEAR310_VIRQ_RS485_1,
-		.status_mask = SPEAR310_RS485_1_IRQ_MASK,
-	},
-};
-
-static struct spear_shirq shirq_intrcomm_ras = {
-	.irq = SPEAR3XX_IRQ_INTRCOMM_RAS_ARM,
-	.dev_config = shirq_intrcomm_ras_config,
-	.dev_count = ARRAY_SIZE(shirq_intrcomm_ras_config),
-	.regs = {
-		.enb_reg = -1,
-		.status_reg = SPEAR310_INT_STS_MASK_REG,
-		.status_reg_mask = SPEAR310_SHIRQ_INTRCOMM_RAS_MASK,
-		.clear_reg = -1,
-	},
-};
 
 /* DMAC platform data's slave info */
 struct pl08x_channel_data spear310_dma_info[] = {
@@ -405,42 +234,11 @@ static struct of_dev_auxdata spear310_auxdata_lookup[] __initdata = {
 
 static void __init spear310_dt_init(void)
 {
-	void __iomem *base;
-	int ret;
-
 	pl080_plat_data.slave_channels = spear310_dma_info;
 	pl080_plat_data.num_slave_channels = ARRAY_SIZE(spear310_dma_info);
 
 	of_platform_populate(NULL, of_default_bus_match_table,
 			spear310_auxdata_lookup, NULL);
-
-	/* shared irq registration */
-	base = ioremap(SPEAR310_SOC_CONFIG_BASE, SZ_4K);
-	if (base) {
-		/* shirq 1 */
-		shirq_ras1.regs.base = base;
-		ret = spear_shirq_register(&shirq_ras1);
-		if (ret)
-			pr_err("Error registering Shared IRQ 1\n");
-
-		/* shirq 2 */
-		shirq_ras2.regs.base = base;
-		ret = spear_shirq_register(&shirq_ras2);
-		if (ret)
-			pr_err("Error registering Shared IRQ 2\n");
-
-		/* shirq 3 */
-		shirq_ras3.regs.base = base;
-		ret = spear_shirq_register(&shirq_ras3);
-		if (ret)
-			pr_err("Error registering Shared IRQ 3\n");
-
-		/* shirq 4 */
-		shirq_intrcomm_ras.regs.base = base;
-		ret = spear_shirq_register(&shirq_intrcomm_ras);
-		if (ret)
-			pr_err("Error registering Shared IRQ 4\n");
-	}
 }
 
 static const char * const spear310_dt_board_compat[] = {

arch/arm/mach-spear3xx/spear320.c

@@ -19,7 +19,6 @@
 #include <linux/of_platform.h>
 #include <asm/hardware/vic.h>
 #include <asm/mach/arch.h>
-#include <plat/shirq.h>
 #include <mach/generic.h>
 #include <mach/spear.h>
 
@@ -28,184 +27,6 @@
 #define SPEAR320_SSP0_BASE		UL(0xA5000000)
 #define SPEAR320_SSP1_BASE		UL(0xA6000000)
 
-/* Interrupt registers offsets and masks */
-#define SPEAR320_INT_STS_MASK_REG		0x04
-#define SPEAR320_INT_CLR_MASK_REG		0x04
-#define SPEAR320_INT_ENB_MASK_REG		0x08
-#define SPEAR320_GPIO_IRQ_MASK			(1 << 0)
-#define SPEAR320_I2S_PLAY_IRQ_MASK		(1 << 1)
-#define SPEAR320_I2S_REC_IRQ_MASK		(1 << 2)
-#define SPEAR320_EMI_IRQ_MASK			(1 << 7)
-#define SPEAR320_CLCD_IRQ_MASK			(1 << 8)
-#define SPEAR320_SPP_IRQ_MASK			(1 << 9)
-#define SPEAR320_SDHCI_IRQ_MASK			(1 << 10)
-#define SPEAR320_CAN_U_IRQ_MASK			(1 << 11)
-#define SPEAR320_CAN_L_IRQ_MASK			(1 << 12)
-#define SPEAR320_UART1_IRQ_MASK			(1 << 13)
-#define SPEAR320_UART2_IRQ_MASK			(1 << 14)
-#define SPEAR320_SSP1_IRQ_MASK			(1 << 15)
-#define SPEAR320_SSP2_IRQ_MASK			(1 << 16)
-#define SPEAR320_SMII0_IRQ_MASK			(1 << 17)
-#define SPEAR320_MII1_SMII1_IRQ_MASK		(1 << 18)
-#define SPEAR320_WAKEUP_SMII0_IRQ_MASK		(1 << 19)
-#define SPEAR320_WAKEUP_MII1_SMII1_IRQ_MASK	(1 << 20)
-#define SPEAR320_I2C1_IRQ_MASK			(1 << 21)
-
-#define SPEAR320_SHIRQ_RAS1_MASK		0x000380
-#define SPEAR320_SHIRQ_RAS3_MASK		0x000007
-#define SPEAR320_SHIRQ_INTRCOMM_RAS_MASK	0x3FF800
-
-/* SPEAr320 Virtual irq definitions */
-/* IRQs sharing IRQ_GEN_RAS_1 */
-#define SPEAR320_VIRQ_EMI			(SPEAR3XX_VIRQ_START + 0)
-#define SPEAR320_VIRQ_CLCD			(SPEAR3XX_VIRQ_START + 1)
-#define SPEAR320_VIRQ_SPP			(SPEAR3XX_VIRQ_START + 2)
-
-/* IRQs sharing IRQ_GEN_RAS_2 */
-#define SPEAR320_IRQ_SDHCI			SPEAR3XX_IRQ_GEN_RAS_2
-
-/* IRQs sharing IRQ_GEN_RAS_3 */
-#define SPEAR320_VIRQ_PLGPIO			(SPEAR3XX_VIRQ_START + 3)
-#define SPEAR320_VIRQ_I2S_PLAY			(SPEAR3XX_VIRQ_START + 4)
-#define SPEAR320_VIRQ_I2S_REC			(SPEAR3XX_VIRQ_START + 5)
-
-/* IRQs sharing IRQ_INTRCOMM_RAS_ARM */
-#define SPEAR320_VIRQ_CANU			(SPEAR3XX_VIRQ_START + 6)
-#define SPEAR320_VIRQ_CANL			(SPEAR3XX_VIRQ_START + 7)
-#define SPEAR320_VIRQ_UART1			(SPEAR3XX_VIRQ_START + 8)
-#define SPEAR320_VIRQ_UART2			(SPEAR3XX_VIRQ_START + 9)
-#define SPEAR320_VIRQ_SSP1			(SPEAR3XX_VIRQ_START + 10)
-#define SPEAR320_VIRQ_SSP2			(SPEAR3XX_VIRQ_START + 11)
-#define SPEAR320_VIRQ_SMII0			(SPEAR3XX_VIRQ_START + 12)
-#define SPEAR320_VIRQ_MII1_SMII1		(SPEAR3XX_VIRQ_START + 13)
-#define SPEAR320_VIRQ_WAKEUP_SMII0		(SPEAR3XX_VIRQ_START + 14)
-#define SPEAR320_VIRQ_WAKEUP_MII1_SMII1		(SPEAR3XX_VIRQ_START + 15)
-#define SPEAR320_VIRQ_I2C1			(SPEAR3XX_VIRQ_START + 16)
-
-/* spear3xx shared irq */
-static struct shirq_dev_config shirq_ras1_config[] = {
-	{
-		.virq = SPEAR320_VIRQ_EMI,
-		.status_mask = SPEAR320_EMI_IRQ_MASK,
-		.clear_mask = SPEAR320_EMI_IRQ_MASK,
-	}, {
-		.virq = SPEAR320_VIRQ_CLCD,
-		.status_mask = SPEAR320_CLCD_IRQ_MASK,
-		.clear_mask = SPEAR320_CLCD_IRQ_MASK,
-	}, {
-		.virq = SPEAR320_VIRQ_SPP,
-		.status_mask = SPEAR320_SPP_IRQ_MASK,
-		.clear_mask = SPEAR320_SPP_IRQ_MASK,
-	},
-};
-
-static struct spear_shirq shirq_ras1 = {
-	.irq = SPEAR3XX_IRQ_GEN_RAS_1,
-	.dev_config = shirq_ras1_config,
-	.dev_count = ARRAY_SIZE(shirq_ras1_config),
-	.regs = {
-		.enb_reg = -1,
-		.status_reg = SPEAR320_INT_STS_MASK_REG,
-		.status_reg_mask = SPEAR320_SHIRQ_RAS1_MASK,
-		.clear_reg = SPEAR320_INT_CLR_MASK_REG,
-		.reset_to_clear = 1,
-	},
-};
-
-static struct shirq_dev_config shirq_ras3_config[] = {
-	{
-		.virq = SPEAR320_VIRQ_PLGPIO,
-		.enb_mask = SPEAR320_GPIO_IRQ_MASK,
-		.status_mask = SPEAR320_GPIO_IRQ_MASK,
-		.clear_mask = SPEAR320_GPIO_IRQ_MASK,
-	}, {
-		.virq = SPEAR320_VIRQ_I2S_PLAY,
-		.enb_mask = SPEAR320_I2S_PLAY_IRQ_MASK,
-		.status_mask = SPEAR320_I2S_PLAY_IRQ_MASK,
-		.clear_mask = SPEAR320_I2S_PLAY_IRQ_MASK,
-	}, {
-		.virq = SPEAR320_VIRQ_I2S_REC,
-		.enb_mask = SPEAR320_I2S_REC_IRQ_MASK,
-		.status_mask = SPEAR320_I2S_REC_IRQ_MASK,
-		.clear_mask = SPEAR320_I2S_REC_IRQ_MASK,
-	},
-};
-
-static struct spear_shirq shirq_ras3 = {
-	.irq = SPEAR3XX_IRQ_GEN_RAS_3,
-	.dev_config = shirq_ras3_config,
-	.dev_count = ARRAY_SIZE(shirq_ras3_config),
-	.regs = {
-		.enb_reg = SPEAR320_INT_ENB_MASK_REG,
-		.reset_to_enb = 1,
-		.status_reg = SPEAR320_INT_STS_MASK_REG,
-		.status_reg_mask = SPEAR320_SHIRQ_RAS3_MASK,
-		.clear_reg = SPEAR320_INT_CLR_MASK_REG,
-		.reset_to_clear = 1,
-	},
-};
-
-static struct shirq_dev_config shirq_intrcomm_ras_config[] = {
-	{
-		.virq = SPEAR320_VIRQ_CANU,
-		.status_mask = SPEAR320_CAN_U_IRQ_MASK,
-		.clear_mask = SPEAR320_CAN_U_IRQ_MASK,
-	}, {
-		.virq = SPEAR320_VIRQ_CANL,
-		.status_mask = SPEAR320_CAN_L_IRQ_MASK,
-		.clear_mask = SPEAR320_CAN_L_IRQ_MASK,
-	}, {
-		.virq = SPEAR320_VIRQ_UART1,
-		.status_mask = SPEAR320_UART1_IRQ_MASK,
-		.clear_mask = SPEAR320_UART1_IRQ_MASK,
-	}, {
-		.virq = SPEAR320_VIRQ_UART2,
-		.status_mask = SPEAR320_UART2_IRQ_MASK,
-		.clear_mask = SPEAR320_UART2_IRQ_MASK,
-	}, {
-		.virq = SPEAR320_VIRQ_SSP1,
-		.status_mask = SPEAR320_SSP1_IRQ_MASK,
-		.clear_mask = SPEAR320_SSP1_IRQ_MASK,
-	}, {
-		.virq = SPEAR320_VIRQ_SSP2,
-		.status_mask = SPEAR320_SSP2_IRQ_MASK,
-		.clear_mask = SPEAR320_SSP2_IRQ_MASK,
-	}, {
-		.virq = SPEAR320_VIRQ_SMII0,
-		.status_mask = SPEAR320_SMII0_IRQ_MASK,
-		.clear_mask = SPEAR320_SMII0_IRQ_MASK,
-	}, {
-		.virq = SPEAR320_VIRQ_MII1_SMII1,
-		.status_mask = SPEAR320_MII1_SMII1_IRQ_MASK,
-		.clear_mask = SPEAR320_MII1_SMII1_IRQ_MASK,
-	}, {
-		.virq = SPEAR320_VIRQ_WAKEUP_SMII0,
-		.status_mask = SPEAR320_WAKEUP_SMII0_IRQ_MASK,
-		.clear_mask = SPEAR320_WAKEUP_SMII0_IRQ_MASK,
-	}, {
-		.virq = SPEAR320_VIRQ_WAKEUP_MII1_SMII1,
-		.status_mask = SPEAR320_WAKEUP_MII1_SMII1_IRQ_MASK,
-		.clear_mask = SPEAR320_WAKEUP_MII1_SMII1_IRQ_MASK,
-	}, {
-		.virq = SPEAR320_VIRQ_I2C1,
-		.status_mask = SPEAR320_I2C1_IRQ_MASK,
-		.clear_mask = SPEAR320_I2C1_IRQ_MASK,
-	},
-};
-
-static struct spear_shirq shirq_intrcomm_ras = {
-	.irq = SPEAR3XX_IRQ_INTRCOMM_RAS_ARM,
-	.dev_config = shirq_intrcomm_ras_config,
-	.dev_count = ARRAY_SIZE(shirq_intrcomm_ras_config),
-	.regs = {
-		.enb_reg = -1,
-		.status_reg = SPEAR320_INT_STS_MASK_REG,
-		.status_reg_mask = SPEAR320_SHIRQ_INTRCOMM_RAS_MASK,
-		.clear_reg = SPEAR320_INT_CLR_MASK_REG,
-		.reset_to_clear = 1,
-	},
-};
-
 /* DMAC platform data's slave info */
 struct pl08x_channel_data spear320_dma_info[] = {
 	{
@@ -416,41 +237,17 @@ static struct of_dev_auxdata spear320_auxdata_lookup[] __initdata = {
 
 static void __init spear320_dt_init(void)
 {
-	void __iomem *base;
-	int ret;
-
 	pl080_plat_data.slave_channels = spear320_dma_info;
 	pl080_plat_data.num_slave_channels = ARRAY_SIZE(spear320_dma_info);
 
 	of_platform_populate(NULL, of_default_bus_match_table,
 			spear320_auxdata_lookup, NULL);
-
-	/* shared irq registration */
-	base = ioremap(SPEAR320_SOC_CONFIG_BASE, SZ_4K);
-	if (base) {
-		/* shirq 1 */
-		shirq_ras1.regs.base = base;
-		ret = spear_shirq_register(&shirq_ras1);
-		if (ret)
-			pr_err("Error registering Shared IRQ 1\n");
-
-		/* shirq 3 */
-		shirq_ras3.regs.base = base;
-		ret = spear_shirq_register(&shirq_ras3);
-		if (ret)
-			pr_err("Error registering Shared IRQ 3\n");
-
-		/* shirq 4 */
-		shirq_intrcomm_ras.regs.base = base;
-		ret = spear_shirq_register(&shirq_intrcomm_ras);
-		if (ret)
-			pr_err("Error registering Shared IRQ 4\n");
-	}
 }
 
 static const char * const spear320_dt_board_compat[] = {
 	"st,spear320",
 	"st,spear320-evb",
+	"st,spear320-hmi",
 	NULL,
 };
 

arch/arm/mach-spear3xx/spear3xx.c

@@ -15,6 +15,7 @@
 
 #include <linux/amba/pl022.h>
 #include <linux/amba/pl08x.h>
+#include <linux/irqchip/spear-shirq.h>
 #include <linux/of_irq.h>
 #include <linux/io.h>
 #include <asm/hardware/pl080.h>
@@ -121,6 +122,9 @@ struct sys_timer spear3xx_timer = {
 
 static const struct of_device_id vic_of_match[] __initconst = {
 	{ .compatible = "arm,pl190-vic", .data = vic_of_init, },
+	{ .compatible = "st,spear300-shirq", .data = spear300_shirq_of_init, },
+	{ .compatible = "st,spear310-shirq", .data = spear310_shirq_of_init, },
+	{ .compatible = "st,spear320-shirq", .data = spear320_shirq_of_init, },
 	{ /* Sentinel */ }
 };
 

arch/arm/plat-spear/Makefile

@@ -5,5 +5,5 @@
 # Common support
 obj-y	:= restart.o time.o
 
-obj-$(CONFIG_ARCH_SPEAR3XX)	+= pl080.o shirq.o
+obj-$(CONFIG_ARCH_SPEAR3XX)	+= pl080.o
 obj-$(CONFIG_ARCH_SPEAR6XX)	+= pl080.o

arch/arm/plat-spear/shirq.c

-/*
- * arch/arm/plat-spear/shirq.c
- *
- * SPEAr platform shared irq layer source file
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar <viresh.linux@gmail.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/err.h>
-#include <linux/io.h>
-#include <linux/irq.h>
-#include <linux/spinlock.h>
-#include <plat/shirq.h>
-
-struct spear_shirq *shirq;
-static DEFINE_SPINLOCK(lock);
-
-static void shirq_irq_mask(struct irq_data *d)
-{
-	struct spear_shirq *shirq = irq_data_get_irq_chip_data(d);
-	u32 val, id = d->irq - shirq->dev_config[0].virq;
-	unsigned long flags;
-
-	if ((shirq->regs.enb_reg == -1) || shirq->dev_config[id].enb_mask == -1)
-		return;
-
-	spin_lock_irqsave(&lock, flags);
-	val = readl(shirq->regs.base + shirq->regs.enb_reg);
-	if (shirq->regs.reset_to_enb)
-		val |= shirq->dev_config[id].enb_mask;
-	else
-		val &= ~(shirq->dev_config[id].enb_mask);
-	writel(val, shirq->regs.base + shirq->regs.enb_reg);
-	spin_unlock_irqrestore(&lock, flags);
-}
-
-static void shirq_irq_unmask(struct irq_data *d)
-{
-	struct spear_shirq *shirq = irq_data_get_irq_chip_data(d);
-	u32 val, id = d->irq - shirq->dev_config[0].virq;
-	unsigned long flags;
-
-	if ((shirq->regs.enb_reg == -1) || shirq->dev_config[id].enb_mask == -1)
-		return;
-
-	spin_lock_irqsave(&lock, flags);
-	val = readl(shirq->regs.base + shirq->regs.enb_reg);
-	if (shirq->regs.reset_to_enb)
-		val &= ~(shirq->dev_config[id].enb_mask);
-	else
-		val |= shirq->dev_config[id].enb_mask;
-	writel(val, shirq->regs.base + shirq->regs.enb_reg);
-	spin_unlock_irqrestore(&lock, flags);
-}
-
-static struct irq_chip shirq_chip = {
-	.name		= "spear_shirq",
-	.irq_ack	= shirq_irq_mask,
-	.irq_mask	= shirq_irq_mask,
-	.irq_unmask	= shirq_irq_unmask,
-};
-
-static void shirq_handler(unsigned irq, struct irq_desc *desc)
-{
-	u32 i, val, mask;
-	struct spear_shirq *shirq = irq_get_handler_data(irq);
-
-	desc->irq_data.chip->irq_ack(&desc->irq_data);
-	while ((val = readl(shirq->regs.base + shirq->regs.status_reg) &
-				shirq->regs.status_reg_mask)) {
-		for (i = 0; (i < shirq->dev_count) && val; i++) {
-			if (!(shirq->dev_config[i].status_mask & val))
-				continue;
-
-			generic_handle_irq(shirq->dev_config[i].virq);
-
-			/* clear interrupt */
-			val &= ~shirq->dev_config[i].status_mask;
-			if ((shirq->regs.clear_reg == -1) ||
-					shirq->dev_config[i].clear_mask == -1)
-				continue;
-			mask = readl(shirq->regs.base + shirq->regs.clear_reg);
-			if (shirq->regs.reset_to_clear)
-				mask &= ~shirq->dev_config[i].clear_mask;
-			else
-				mask |= shirq->dev_config[i].clear_mask;
-			writel(mask, shirq->regs.base + shirq->regs.clear_reg);
-		}
-	}
-	desc->irq_data.chip->irq_unmask(&desc->irq_data);
-}
-
-int spear_shirq_register(struct spear_shirq *shirq)
-{
-	int i;
-
-	if (!shirq || !shirq->dev_config || !shirq->regs.base)
-		return -EFAULT;
-
-	if (!shirq->dev_count)
-		return -EINVAL;
-
-	irq_set_chained_handler(shirq->irq, shirq_handler);
-	for (i = 0; i < shirq->dev_count; i++) {
-		irq_set_chip_and_handler(shirq->dev_config[i].virq,
-					 &shirq_chip, handle_simple_irq);
-		set_irq_flags(shirq->dev_config[i].virq, IRQF_VALID);
-		irq_set_chip_data(shirq->dev_config[i].virq, shirq);
-	}
-
-	irq_set_handler_data(shirq->irq, shirq);
-	return 0;
-}

drivers/clk/spear/spear1310_clock.c

@@ -20,6 +20,7 @@
 #include <mach/spear.h>
 #include "clk.h"
 
+#define VA_SPEAR1310_RAS_BASE			IOMEM(UL(0xFA400000))
 /* PLL related registers and bit values */
 #define SPEAR1310_PLL_CFG			(VA_MISC_BASE + 0x210)
 	/* PLL_CFG bit values */

drivers/irqchip/Makefile

 obj-$(CONFIG_ARCH_BCM2835)		+= irq-bcm2835.o
 obj-$(CONFIG_ARCH_SUNXI)		+= irq-sunxi.o
 obj-$(CONFIG_VERSATILE_FPGA_IRQ)	+= irq-versatile-fpga.o
+obj-$(CONFIG_ARCH_SPEAR3XX)		+= spear-shirq.o

drivers/irqchip/spear-shirq.c

+/*
+ * SPEAr platform shared irq layer source file
+ *
+ * Copyright (C) 2009-2012 ST Microelectronics
+ * Viresh Kumar <viresh.linux@gmail.com>
+ *
+ * Copyright (C) 2012 ST Microelectronics
+ * Shiraz Hashim <shiraz.hashim@st.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/err.h>
+#include <linux/export.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/irqchip/spear-shirq.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/spinlock.h>
+
+static DEFINE_SPINLOCK(lock);
+
+/* spear300 shared irq registers offsets and masks */
+#define SPEAR300_INT_ENB_MASK_REG	0x54
+#define SPEAR300_INT_STS_MASK_REG	0x58
+
+static struct spear_shirq spear300_shirq_ras1 = {
+	.irq_nr = 9,
+	.irq_bit_off = 0,
+	.regs = {
+		.enb_reg = SPEAR300_INT_ENB_MASK_REG,
+		.status_reg = SPEAR300_INT_STS_MASK_REG,
+		.clear_reg = -1,
+	},
+};
+
+static struct spear_shirq *spear300_shirq_blocks[] = {
+	&spear300_shirq_ras1,
+};
+
+/* spear310 shared irq registers offsets and masks */
+#define SPEAR310_INT_STS_MASK_REG	0x04
+
+static struct spear_shirq spear310_shirq_ras1 = {
+	.irq_nr = 8,
+	.irq_bit_off = 0,
+	.regs = {
+		.enb_reg = -1,
+		.status_reg = SPEAR310_INT_STS_MASK_REG,
+		.clear_reg = -1,
+	},
+};
+
+static struct spear_shirq spear310_shirq_ras2 = {
+	.irq_nr = 5,
+	.irq_bit_off = 8,
+	.regs = {
+		.enb_reg = -1,
+		.status_reg = SPEAR310_INT_STS_MASK_REG,
+		.clear_reg = -1,
+	},
+};
+
+static struct spear_shirq spear310_shirq_ras3 = {
+	.irq_nr = 1,
+	.irq_bit_off = 13,
+	.regs = {
+		.enb_reg = -1,
+		.status_reg = SPEAR310_INT_STS_MASK_REG,
+		.clear_reg = -1,
+	},
+};
+
+static struct spear_shirq spear310_shirq_intrcomm_ras = {
+	.irq_nr = 3,
+	.irq_bit_off = 14,
+	.regs = {
+		.enb_reg = -1,
+		.status_reg = SPEAR310_INT_STS_MASK_REG,
+		.clear_reg = -1,
+	},
+};
+
+static struct spear_shirq *spear310_shirq_blocks[] = {
+	&spear310_shirq_ras1,
+	&spear310_shirq_ras2,
+	&spear310_shirq_ras3,
+	&spear310_shirq_intrcomm_ras,
+};
+
+/* spear320 shared irq registers offsets and masks */
+#define SPEAR320_INT_STS_MASK_REG		0x04
+#define SPEAR320_INT_CLR_MASK_REG		0x04
+#define SPEAR320_INT_ENB_MASK_REG		0x08
+
+static struct spear_shirq spear320_shirq_ras1 = {
+	.irq_nr = 3,
+	.irq_bit_off = 7,
+	.regs = {
+		.enb_reg = -1,
+		.status_reg = SPEAR320_INT_STS_MASK_REG,
+		.clear_reg = SPEAR320_INT_CLR_MASK_REG,
+		.reset_to_clear = 1,
+	},
+};
+
+static struct spear_shirq spear320_shirq_ras2 = {
+	.irq_nr = 1,
+	.irq_bit_off = 10,
+	.regs = {
+		.enb_reg = -1,
+		.status_reg = SPEAR320_INT_STS_MASK_REG,
+		.clear_reg = SPEAR320_INT_CLR_MASK_REG,
+		.reset_to_clear = 1,
+	},
+};
+
+static struct spear_shirq spear320_shirq_ras3 = {
+	.irq_nr = 3,
+	.irq_bit_off = 0,
+	.invalid_irq = 1,
+	.regs = {
+		.enb_reg = SPEAR320_INT_ENB_MASK_REG,
+		.reset_to_enb = 1,
+		.status_reg = SPEAR320_INT_STS_MASK_REG,
+		.clear_reg = SPEAR320_INT_CLR_MASK_REG,
+		.reset_to_clear = 1,
+	},
+};
+
+static struct spear_shirq spear320_shirq_intrcomm_ras = {
+	.irq_nr = 11,
+	.irq_bit_off = 11,
+	.regs = {
+		.enb_reg = -1,
+		.status_reg = SPEAR320_INT_STS_MASK_REG,
+		.clear_reg = SPEAR320_INT_CLR_MASK_REG,
+		.reset_to_clear = 1,
+	},
+};
+
+static struct spear_shirq *spear320_shirq_blocks[] = {
+	&spear320_shirq_ras3,
+	&spear320_shirq_ras1,
+	&spear320_shirq_ras2,
+	&spear320_shirq_intrcomm_ras,
+};
+
+static void shirq_irq_mask_unmask(struct irq_data *d, bool mask)
+{
+	struct spear_shirq *shirq = irq_data_get_irq_chip_data(d);
+	u32 val, offset = d->irq - shirq->irq_base;
+	unsigned long flags;
+
+	if (shirq->regs.enb_reg == -1)
+		return;
+
+	spin_lock_irqsave(&lock, flags);
+	val = readl(shirq->base + shirq->regs.enb_reg);
+
+	if (mask ^ shirq->regs.reset_to_enb)
+		val &= ~(0x1 << shirq->irq_bit_off << offset);
+	else
+		val |= 0x1 << shirq->irq_bit_off << offset;
+
+	writel(val, shirq->base + shirq->regs.enb_reg);
+	spin_unlock_irqrestore(&lock, flags);
+
+}
+
+static void shirq_irq_mask(struct irq_data *d)
+{
+	shirq_irq_mask_unmask(d, 1);
+}
+
+static void shirq_irq_unmask(struct irq_data *d)
+{
+	shirq_irq_mask_unmask(d, 0);
+}
+
+static struct irq_chip shirq_chip = {
+	.name		= "spear-shirq",
+	.irq_ack	= shirq_irq_mask,
+	.irq_mask	= shirq_irq_mask,
+	.irq_unmask	= shirq_irq_unmask,
+};
+
+static void shirq_handler(unsigned irq, struct irq_desc *desc)
+{
+	u32 i, j, val, mask, tmp;
+	struct irq_chip *chip;
+	struct spear_shirq *shirq = irq_get_handler_data(irq);
+
+	chip = irq_get_chip(irq);
+	chip->irq_ack(&desc->irq_data);
+
+	mask = ((0x1 << shirq->irq_nr) - 1) << shirq->irq_bit_off;
+	while ((val = readl(shirq->base + shirq->regs.status_reg) &
+				mask)) {
+
+		val >>= shirq->irq_bit_off;
+		for (i = 0, j = 1; i < shirq->irq_nr; i++, j <<= 1) {
+
+			if (!(j & val))
+				continue;
+
+			generic_handle_irq(shirq->irq_base + i);
+
+			/* clear interrupt */
+			if (shirq->regs.clear_reg == -1)
+				continue;
+
+			tmp = readl(shirq->base + shirq->regs.clear_reg);
+			if (shirq->regs.reset_to_clear)
+				tmp &= ~(j << shirq->irq_bit_off);
+			else
+				tmp |= (j << shirq->irq_bit_off);
+			writel(tmp, shirq->base + shirq->regs.clear_reg);
+		}
+	}
+	chip->irq_unmask(&desc->irq_data);
+}
+
+static void __init spear_shirq_register(struct spear_shirq *shirq)
+{
+	int i;
+
+	if (shirq->invalid_irq)
+		return;
+
+	irq_set_chained_handler(shirq->irq, shirq_handler);
+	for (i = 0; i < shirq->irq_nr; i++) {
+		irq_set_chip_and_handler(shirq->irq_base + i,
+					 &shirq_chip, handle_simple_irq);
+		set_irq_flags(shirq->irq_base + i, IRQF_VALID);
+		irq_set_chip_data(shirq->irq_base + i, shirq);
+	}
+
+	irq_set_handler_data(shirq->irq, shirq);
+}
+
+static int __init shirq_init(struct spear_shirq **shirq_blocks, int block_nr,
+		struct device_node *np)
+{
+	int i, irq_base, hwirq = 0, irq_nr = 0;
+	static struct irq_domain *shirq_domain;
+	void __iomem *base;
+
+	base = of_iomap(np, 0);
+	if (!base) {
+		pr_err("%s: failed to map shirq registers\n", __func__);
+		return -ENXIO;
+	}
+
+	for (i = 0; i < block_nr; i++)
+		irq_nr += shirq_blocks[i]->irq_nr;
+
+	irq_base = irq_alloc_descs(-1, 0, irq_nr, 0);
+	if (IS_ERR_VALUE(irq_base)) {
+		pr_err("%s: irq desc alloc failed\n", __func__);
+		goto err_unmap;
+	}
+
+	shirq_domain = irq_domain_add_legacy(np, irq_nr, irq_base, 0,
+			&irq_domain_simple_ops, NULL);
+	if (WARN_ON(!shirq_domain)) {
+		pr_warn("%s: irq domain init failed\n", __func__);
+		goto err_free_desc;
+	}
+
+	for (i = 0; i < block_nr; i++) {
+		shirq_blocks[i]->base = base;
+		shirq_blocks[i]->irq_base = irq_find_mapping(shirq_domain,
+				hwirq);
+		shirq_blocks[i]->irq = irq_of_parse_and_map(np, i);
+
+		spear_shirq_register(shirq_blocks[i]);
+		hwirq += shirq_blocks[i]->irq_nr;
+	}
+
+	return 0;
+
+err_free_desc:
+	irq_free_descs(irq_base, irq_nr);
+err_unmap:
+	iounmap(base);
+	return -ENXIO;
+}
+
+int __init spear300_shirq_of_init(struct device_node *np,
+		struct device_node *parent)
+{
+	return shirq_init(spear300_shirq_blocks,
+			ARRAY_SIZE(spear300_shirq_blocks), np);
+}
+
+int __init spear310_shirq_of_init(struct device_node *np,
+		struct device_node *parent)
+{
+	return shirq_init(spear310_shirq_blocks,
+			ARRAY_SIZE(spear310_shirq_blocks), np);
+}
+
+int __init spear320_shirq_of_init(struct device_node *np,
+		struct device_node *parent)
+{
+	return shirq_init(spear320_shirq_blocks,
+			ARRAY_SIZE(spear320_shirq_blocks), np);
+}

arch/arm/plat-spear/include/plat/shirq.h → include/linux/irqchip/spear-shirq.h

 /*
- * arch/arm/plat-spear/include/plat/shirq.h
- *
  * SPEAr platform shared irq layer header file
  *
- * Copyright (C) 2009 ST Microelectronics
+ * Copyright (C) 2009-2012 ST Microelectronics
  * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
@@ -11,31 +9,15 @@
  * warranty of any kind, whether express or implied.
  */
 
-#ifndef __PLAT_SHIRQ_H
-#define __PLAT_SHIRQ_H
+#ifndef __SPEAR_SHIRQ_H
+#define __SPEAR_SHIRQ_H
 
 #include <linux/irq.h>
 #include <linux/types.h>
 
-/*
- * struct shirq_dev_config: shared irq device configuration
- *
- * virq: virtual irq number of device
- * enb_mask: enable mask of device
- * status_mask: status mask of device
- * clear_mask: clear mask of device
- */
-struct shirq_dev_config {
-	u32 virq;
-	u32 enb_mask;
-	u32 status_mask;
-	u32 clear_mask;
-};
-
 /*
  * struct shirq_regs: shared irq register configuration
  *
- * base: base address of shared irq register
  * enb_reg: enable register offset
  * reset_to_enb: val 1 indicates, we need to clear bit for enabling interrupt
  * status_reg: status register offset
@@ -44,11 +26,9 @@ struct shirq_dev_config {
  * reset_to_clear: val 1 indicates, we need to clear bit for clearing interrupt
  */
 struct shirq_regs {
-	void __iomem *base;
 	u32 enb_reg;
 	u32 reset_to_enb;
 	u32 status_reg;
-	u32 status_reg_mask;
 	u32 clear_reg;
 	u32 reset_to_clear;
 };
@@ -57,17 +37,28 @@ struct shirq_regs {
  * struct spear_shirq: shared irq structure
  *
  * irq: hardware irq number
- * dev_config: array of device config structures which are using "irq" line
- * dev_count: size of dev_config array
+ * irq_base: base irq in linux domain
+ * irq_nr: no. of shared interrupts in a particular block
+ * irq_bit_off: starting bit offset in the status register
+ * invalid_irq: irq group is currently disabled
+ * base: base address of shared irq register
  * regs: register configuration for shared irq block
  */
 struct spear_shirq {
 	u32 irq;
-	struct shirq_dev_config *dev_config;
-	u32 dev_count;
+	u32 irq_base;
+	u32 irq_nr;
+	u32 irq_bit_off;
+	int invalid_irq;
+	void __iomem *base;
 	struct shirq_regs regs;
 };
 
-int spear_shirq_register(struct spear_shirq *shirq);
+int __init spear300_shirq_of_init(struct device_node *np,
+		struct device_node *parent);
+int __init spear310_shirq_of_init(struct device_node *np,
+		struct device_node *parent);
+int __init spear320_shirq_of_init(struct device_node *np,
+		struct device_node *parent);
 
-#endif /* __PLAT_SHIRQ_H */
+#endif /* __SPEAR_SHIRQ_H */