Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  eeepc-laptop: fix hot-unplug on resume
  ACPI: Ingore the memory block with zero block size in course of memory hotplug
  ACPI: Don't treat generic error as ACPI error code in acpi memory hotplug driver
  ACPI: bind workqueues to CPU 0 to avoid SMI corruption
  ACPI: root-only read protection on /sys/firmware/acpi/tables/*
  thinkpad-acpi: fix incorrect use of TPACPI_BRGHT_MODE_ECNVRAM
  thinkpad-acpi: restrict procfs count value to sane upper limit
  thinkpad-acpi: remove dock and bay subdrivers
  thinkpad-acpi: disable broken bay and dock subdrivers
  hp-wmi: check that an input device exists in resume handler
  Revert "ACPICA: Remove obsolete acpi_os_validate_address interface"

Documentation/laptops/thinkpad-acpi.txt

@@ -36,8 +36,6 @@ detailed description):
 	- Bluetooth enable and disable
 	- video output switching, expansion control
 	- ThinkLight on and off
-	- limited docking and undocking
-	- UltraBay eject
 	- CMOS/UCMS control
 	- LED control
 	- ACPI sounds
@@ -729,131 +727,6 @@ cannot be read or if it is unknown, thinkpad-acpi will report it as "off".
 It is impossible to know if the status returned through sysfs is valid.
 
 
-Docking / undocking -- /proc/acpi/ibm/dock
-------------------------------------------
-
-Docking and undocking (e.g. with the X4 UltraBase) requires some
-actions to be taken by the operating system to safely make or break
-the electrical connections with the dock.
-
-The docking feature of this driver generates the following ACPI events:
-
-	ibm/dock GDCK 00000003 00000001 -- eject request
-	ibm/dock GDCK 00000003 00000002 -- undocked
-	ibm/dock GDCK 00000000 00000003 -- docked
-
-NOTE: These events will only be generated if the laptop was docked
-when originally booted. This is due to the current lack of support for
-hot plugging of devices in the Linux ACPI framework. If the laptop was
-booted while not in the dock, the following message is shown in the
-logs:
-
-	Mar 17 01:42:34 aero kernel: thinkpad_acpi: dock device not present
-
-In this case, no dock-related events are generated but the dock and
-undock commands described below still work. They can be executed
-manually or triggered by Fn key combinations (see the example acpid
-configuration files included in the driver tarball package available
-on the web site).
-
-When the eject request button on the dock is pressed, the first event
-above is generated. The handler for this event should issue the
-following command:
-
-	echo undock > /proc/acpi/ibm/dock
-
-After the LED on the dock goes off, it is safe to eject the laptop.
-Note: if you pressed this key by mistake, go ahead and eject the
-laptop, then dock it back in. Otherwise, the dock may not function as
-expected.
-
-When the laptop is docked, the third event above is generated. The
-handler for this event should issue the following command to fully
-enable the dock:
-
-	echo dock > /proc/acpi/ibm/dock
-
-The contents of the /proc/acpi/ibm/dock file shows the current status
-of the dock, as provided by the ACPI framework.
-
-The docking support in this driver does not take care of enabling or
-disabling any other devices you may have attached to the dock. For
-example, a CD drive plugged into the UltraBase needs to be disabled or
-enabled separately. See the provided example acpid configuration files
-for how this can be accomplished.
-
-There is no support yet for PCI devices that may be attached to a
-docking station, e.g. in the ThinkPad Dock II. The driver currently
-does not recognize, enable or disable such devices. This means that
-the only docking stations currently supported are the X-series
-UltraBase docks and "dumb" port replicators like the Mini Dock (the
-latter don't need any ACPI support, actually).
-
-
-UltraBay eject -- /proc/acpi/ibm/bay
-------------------------------------
-
-Inserting or ejecting an UltraBay device requires some actions to be
-taken by the operating system to safely make or break the electrical
-connections with the device.
-
-This feature generates the following ACPI events:
-
-	ibm/bay MSTR 00000003 00000000 -- eject request
-	ibm/bay MSTR 00000001 00000000 -- eject lever inserted
-
-NOTE: These events will only be generated if the UltraBay was present
-when the laptop was originally booted (on the X series, the UltraBay
-is in the dock, so it may not be present if the laptop was undocked).
-This is due to the current lack of support for hot plugging of devices
-in the Linux ACPI framework. If the laptop was booted without the
-UltraBay, the following message is shown in the logs:
-
-	Mar 17 01:42:34 aero kernel: thinkpad_acpi: bay device not present
-
-In this case, no bay-related events are generated but the eject
-command described below still works. It can be executed manually or
-triggered by a hot key combination.
-
-Sliding the eject lever generates the first event shown above. The
-handler for this event should take whatever actions are necessary to
-shut down the device in the UltraBay (e.g. call idectl), then issue
-the following command:
-
-	echo eject > /proc/acpi/ibm/bay
-
-After the LED on the UltraBay goes off, it is safe to pull out the
-device.
-
-When the eject lever is inserted, the second event above is
-generated. The handler for this event should take whatever actions are
-necessary to enable the UltraBay device (e.g. call idectl).
-
-The contents of the /proc/acpi/ibm/bay file shows the current status
-of the UltraBay, as provided by the ACPI framework.
-
-EXPERIMENTAL warm eject support on the 600e/x, A22p and A3x (To use
-this feature, you need to supply the experimental=1 parameter when
-loading the module):
-
-These models do not have a button near the UltraBay device to request
-a hot eject but rather require the laptop to be put to sleep
-(suspend-to-ram) before the bay device is ejected or inserted).
-The sequence of steps to eject the device is as follows:
-
-	echo eject > /proc/acpi/ibm/bay
-	put the ThinkPad to sleep
-	remove the drive
-	resume from sleep
-	cat /proc/acpi/ibm/bay should show that the drive was removed
-
-On the A3x, both the UltraBay 2000 and UltraBay Plus devices are
-supported. Use "eject2" instead of "eject" for the second bay.
-
-Note: the UltraBay eject support on the 600e/x, A22p and A3x is
-EXPERIMENTAL and may not work as expected. USE WITH CAUTION!
-
-
 CMOS/UCMS control
 -----------------
 

drivers/acpi/acpi_memhotplug.c

@@ -38,6 +38,9 @@
 
 #define _COMPONENT		ACPI_MEMORY_DEVICE_COMPONENT
 
+#undef PREFIX
+#define 	PREFIX		"ACPI:memory_hp:"
+
 ACPI_MODULE_NAME("acpi_memhotplug");
 MODULE_AUTHOR("Naveen B S <naveen.b.s@intel.com>");
 MODULE_DESCRIPTION("Hotplug Mem Driver");
@@ -153,6 +156,7 @@ acpi_memory_get_device(acpi_handle handle,
 	acpi_handle phandle;
 	struct acpi_device *device = NULL;
 	struct acpi_device *pdevice = NULL;
+	int result;
 
 
 	if (!acpi_bus_get_device(handle, &device) && device)
@@ -165,9 +169,9 @@ acpi_memory_get_device(acpi_handle handle,
 	}
 
 	/* Get the parent device */
-	status = acpi_bus_get_device(phandle, &pdevice);
-	if (ACPI_FAILURE(status)) {
-		ACPI_EXCEPTION((AE_INFO, status, "Cannot get acpi bus device"));
+	result = acpi_bus_get_device(phandle, &pdevice);
+	if (result) {
+		printk(KERN_WARNING PREFIX "Cannot get acpi bus device");
 		return -EINVAL;
 	}
 
@@ -175,9 +179,9 @@ acpi_memory_get_device(acpi_handle handle,
 	 * Now add the notified device.  This creates the acpi_device
 	 * and invokes .add function
 	 */
-	status = acpi_bus_add(&device, pdevice, handle, ACPI_BUS_TYPE_DEVICE);
-	if (ACPI_FAILURE(status)) {
-		ACPI_EXCEPTION((AE_INFO, status, "Cannot add acpi bus"));
+	result = acpi_bus_add(&device, pdevice, handle, ACPI_BUS_TYPE_DEVICE);
+	if (result) {
+		printk(KERN_WARNING PREFIX "Cannot add acpi bus");
 		return -EINVAL;
 	}
 
@@ -238,7 +242,12 @@ static int acpi_memory_enable_device(struct acpi_memory_device *mem_device)
 			num_enabled++;
 			continue;
 		}
-
+		/*
+		 * If the memory block size is zero, please ignore it.
+		 * Don't try to do the following memory hotplug flowchart.
+		 */
+		if (!info->length)
+			continue;
 		if (node < 0)
 			node = memory_add_physaddr_to_nid(info->start_addr);
 
@@ -253,8 +262,15 @@ static int acpi_memory_enable_device(struct acpi_memory_device *mem_device)
 		mem_device->state = MEMORY_INVALID_STATE;
 		return -EINVAL;
 	}
-
-	return result;
+	/*
+	 * Sometimes the memory device will contain several memory blocks.
+	 * When one memory block is hot-added to the system memory, it will
+	 * be regarded as a success.
+	 * Otherwise if the last memory block can't be hot-added to the system
+	 * memory, it will be failure and the memory device can't be bound with
+	 * driver.
+	 */
+	return 0;
 }
 
 static int acpi_memory_powerdown_device(struct acpi_memory_device *mem_device)

drivers/acpi/acpica/acobject.h

@@ -97,6 +97,7 @@
 #define AOPOBJ_OBJECT_INITIALIZED   0x08
 #define AOPOBJ_SETUP_COMPLETE       0x10
 #define AOPOBJ_SINGLE_DATUM         0x20
+#define AOPOBJ_INVALID              0x40	/* Used if host OS won't allow an op_region address */
 
 /******************************************************************************
  *

drivers/acpi/acpica/dsopcode.c

@@ -397,6 +397,30 @@ acpi_status acpi_ds_get_region_arguments(union acpi_operand_object *obj_desc)
 	status = acpi_ds_execute_arguments(node, acpi_ns_get_parent_node(node),
 					   extra_desc->extra.aml_length,
 					   extra_desc->extra.aml_start);
+	if (ACPI_FAILURE(status)) {
+		return_ACPI_STATUS(status);
+	}
+
+	/* Validate the region address/length via the host OS */
+
+	status = acpi_os_validate_address(obj_desc->region.space_id,
+					  obj_desc->region.address,
+					  (acpi_size) obj_desc->region.length,
+					  acpi_ut_get_node_name(node));
+
+	if (ACPI_FAILURE(status)) {
+		/*
+		 * Invalid address/length. We will emit an error message and mark
+		 * the region as invalid, so that it will cause an additional error if
+		 * it is ever used. Then return AE_OK.
+		 */
+		ACPI_EXCEPTION((AE_INFO, status,
+				"During address validation of OpRegion [%4.4s]",
+				node->name.ascii));
+		obj_desc->common.flags |= AOPOBJ_INVALID;
+		status = AE_OK;
+	}
+
 	return_ACPI_STATUS(status);
 }
 

drivers/acpi/acpica/exfldio.c

@@ -113,6 +113,12 @@ acpi_ex_setup_region(union acpi_operand_object *obj_desc,
 		}
 	}
 
+	/* Exit if Address/Length have been disallowed by the host OS */
+
+	if (rgn_desc->common.flags & AOPOBJ_INVALID) {
+		return_ACPI_STATUS(AE_AML_ILLEGAL_ADDRESS);
+	}
+
 	/*
 	 * Exit now for SMBus address space, it has a non-linear address space
 	 * and the request cannot be directly validated

drivers/acpi/osl.c

@@ -189,11 +189,36 @@ acpi_status __init acpi_os_initialize(void)
 	return AE_OK;
 }
 
+static void bind_to_cpu0(struct work_struct *work)
+{
+	set_cpus_allowed(current, cpumask_of_cpu(0));
+	kfree(work);
+}
+
+static void bind_workqueue(struct workqueue_struct *wq)
+{
+	struct work_struct *work;
+
+	work = kzalloc(sizeof(struct work_struct), GFP_KERNEL);
+	INIT_WORK(work, bind_to_cpu0);
+	queue_work(wq, work);
+}
+
 acpi_status acpi_os_initialize1(void)
 {
+	/*
+	 * On some machines, a software-initiated SMI causes corruption unless
+	 * the SMI runs on CPU 0.  An SMI can be initiated by any AML, but
+	 * typically it's done in GPE-related methods that are run via
+	 * workqueues, so we can avoid the known corruption cases by binding
+	 * the workqueues to CPU 0.
+	 */
 	kacpid_wq = create_singlethread_workqueue("kacpid");
+	bind_workqueue(kacpid_wq);
 	kacpi_notify_wq = create_singlethread_workqueue("kacpi_notify");
+	bind_workqueue(kacpi_notify_wq);
 	kacpi_hotplug_wq = create_singlethread_workqueue("kacpi_hotplug");
+	bind_workqueue(kacpi_hotplug_wq);
 	BUG_ON(!kacpid_wq);
 	BUG_ON(!kacpi_notify_wq);
 	BUG_ON(!kacpi_hotplug_wq);

drivers/acpi/system.c

@@ -121,7 +121,7 @@ static void acpi_table_attr_init(struct acpi_table_attr *table_attr,
 	table_attr->attr.size = 0;
 	table_attr->attr.read = acpi_table_show;
 	table_attr->attr.attr.name = table_attr->name;
-	table_attr->attr.attr.mode = 0444;
+	table_attr->attr.attr.mode = 0400;
 
 	return;
 }

drivers/platform/x86/Kconfig

@@ -277,31 +277,6 @@ config THINKPAD_ACPI_UNSAFE_LEDS
 	  Say N here, unless you are building a kernel for your own
 	  use, and need to control the important firmware LEDs.
 
-config THINKPAD_ACPI_DOCK
-	bool "Legacy Docking Station Support"
-	depends on THINKPAD_ACPI
-	depends on ACPI_DOCK=n
-	default n
-	---help---
-	  Allows the thinkpad_acpi driver to handle docking station events.
-	  This support was made obsolete by the generic ACPI docking station
-	  support (CONFIG_ACPI_DOCK).  It will allow locking and removing the
-	  laptop from the docking station, but will not properly connect PCI
-	  devices.
-
-	  If you are not sure, say N here.
-
-config THINKPAD_ACPI_BAY
-	bool "Legacy Removable Bay Support"
-	depends on THINKPAD_ACPI
-	default y
-	---help---
-	  Allows the thinkpad_acpi driver to handle removable bays.  It will
-	  electrically disable the device in the bay, and also generate
-	  notifications when the bay lever is ejected or inserted.
-
-	  If you are not sure, say Y here.
-
 config THINKPAD_ACPI_VIDEO
 	bool "Video output control support"
 	depends on THINKPAD_ACPI

drivers/platform/x86/eeepc-laptop.c

@@ -143,6 +143,7 @@ struct eeepc_hotk {
 	struct rfkill *bluetooth_rfkill;
 	struct rfkill *wwan3g_rfkill;
 	struct hotplug_slot *hotplug_slot;
+	struct work_struct hotplug_work;
 };
 
 /* The actual device the driver binds to */
@@ -660,7 +661,7 @@ static int eeepc_get_adapter_status(struct hotplug_slot *hotplug_slot,
 	return 0;
 }
 
-static void eeepc_rfkill_hotplug(void)
+static void eeepc_hotplug_work(struct work_struct *work)
 {
 	struct pci_dev *dev;
 	struct pci_bus *bus = pci_find_bus(0, 1);
@@ -701,7 +702,7 @@ static void eeepc_rfkill_notify(acpi_handle handle, u32 event, void *data)
 	if (event != ACPI_NOTIFY_BUS_CHECK)
 		return;
 
-	eeepc_rfkill_hotplug();
+	schedule_work(&ehotk->hotplug_work);
 }
 
 static void eeepc_hotk_notify(struct acpi_device *device, u32 event)
@@ -892,7 +893,7 @@ static int eeepc_hotk_resume(struct acpi_device *device)
 
 		rfkill_set_sw_state(ehotk->wlan_rfkill, wlan != 1);
 
-		eeepc_rfkill_hotplug();
+		schedule_work(&ehotk->hotplug_work);
 	}
 
 	if (ehotk->bluetooth_rfkill)
@@ -1093,6 +1094,8 @@ static int eeepc_rfkill_init(struct device *dev)
 {
 	int result = 0;
 
+	INIT_WORK(&ehotk->hotplug_work, eeepc_hotplug_work);
+
 	eeepc_register_rfkill_notifier("\\_SB.PCI0.P0P6");
 	eeepc_register_rfkill_notifier("\\_SB.PCI0.P0P7");
 

drivers/platform/x86/hp-wmi.c

@@ -520,11 +520,13 @@ static int hp_wmi_resume_handler(struct platform_device *device)
 	 * the input layer will only actually pass it on if the state
 	 * changed.
 	 */
-
-	input_report_switch(hp_wmi_input_dev, SW_DOCK, hp_wmi_dock_state());
-	input_report_switch(hp_wmi_input_dev, SW_TABLET_MODE,
-			    hp_wmi_tablet_state());
-	input_sync(hp_wmi_input_dev);
+	if (hp_wmi_input_dev) {
+		input_report_switch(hp_wmi_input_dev, SW_DOCK,
+				    hp_wmi_dock_state());
+		input_report_switch(hp_wmi_input_dev, SW_TABLET_MODE,
+				    hp_wmi_tablet_state());
+		input_sync(hp_wmi_input_dev);
+	}
 
 	return 0;
 }

include/acpi/acpiosxf.h

@@ -242,6 +242,10 @@ acpi_os_derive_pci_id(acpi_handle rhandle,
 acpi_status acpi_os_validate_interface(char *interface);
 acpi_status acpi_osi_invalidate(char* interface);
 
+acpi_status
+acpi_os_validate_address(u8 space_id, acpi_physical_address address,
+			 acpi_size length, char *name);
+
 u64 acpi_os_get_timer(void);
 
 acpi_status acpi_os_signal(u32 function, void *info);