usb: host: remove ehci-pxa168.c

Since ehci-mv.c can cover Marvell PXA and MMP series including PXA168,
so this driver seems redundant now.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Cc: <tanmay.upadhyay@einfochips.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/usb/host/Kconfig

@@ -606,10 +606,3 @@ config USB_OCTEON_OHCI
 config USB_OCTEON2_COMMON
 	bool
 	default y if USB_OCTEON_EHCI || USB_OCTEON_OHCI
-
-config USB_PXA168_EHCI
-	bool "Marvell PXA168 on-chip EHCI HCD support"
-	depends on USB_EHCI_HCD && ARCH_MMP
-	help
-	  Enable support for Marvell PXA168 SoC's on-chip EHCI
-	  host controller

drivers/usb/host/ehci-hcd.c

@@ -1361,11 +1361,6 @@ MODULE_LICENSE ("GPL");
 #define PLATFORM_DRIVER		ehci_grlib_driver
 #endif
 
-#ifdef CONFIG_USB_PXA168_EHCI
-#include "ehci-pxa168.c"
-#define PLATFORM_DRIVER		ehci_pxa168_driver
-#endif
-
 #ifdef CONFIG_CPU_XLR
 #include "ehci-xls.c"
 #define PLATFORM_DRIVER		ehci_xls_driver

drivers/usb/host/ehci-pxa168.c

-/*
- * drivers/usb/host/ehci-pxa168.c
- *
- * Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
- *
- * Based on drivers/usb/host/ehci-orion.c
- *
- * This file is licensed under  the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/clk.h>
-#include <mach/pxa168.h>
-
-#define USB_PHY_CTRL_REG 0x4
-#define USB_PHY_PLL_REG  0x8
-#define USB_PHY_TX_REG   0xc
-
-#define FBDIV_SHIFT      4
-
-#define ICP_SHIFT        12
-#define ICP_15            2
-#define ICP_20            3
-#define ICP_25            4
-
-#define KVCO_SHIFT       15
-
-#define PLLCALI12_SHIFT  25
-#define CALI12_VDD        0
-#define CALI12_09         1
-#define CALI12_10         2
-#define CALI12_11         3
-
-#define PLLVDD12_SHIFT   27
-#define VDD12_VDD         0
-#define VDD12_10          1
-#define VDD12_11          2
-#define VDD12_12          3
-
-#define PLLVDD18_SHIFT   29
-#define VDD18_19          0
-#define VDD18_20          1
-#define VDD18_21          2
-#define VDD18_22          3
-
-
-#define PLL_READY        (1 << 23)
-#define VCOCAL_START     (1 << 21)
-#define REG_RCAL_START   (1 << 12)
-
-struct pxa168_usb_drv_data {
-	struct ehci_hcd ehci;
-	struct clk	*pxa168_usb_clk;
-	struct resource	*usb_phy_res;
-	void __iomem	*usb_phy_reg_base;
-};
-
-static int ehci_pxa168_setup(struct usb_hcd *hcd)
-{
-	struct ehci_hcd *ehci = hcd_to_ehci(hcd);
-	int retval;
-
-	ehci_reset(ehci);
-	retval = ehci_halt(ehci);
-	if (retval)
-		return retval;
-
-	/*
-	 * data structure init
-	 */
-	retval = ehci_init(hcd);
-	if (retval)
-		return retval;
-
-	hcd->has_tt = 1;
-
-	ehci_port_power(ehci, 0);
-
-	return retval;
-}
-
-static const struct hc_driver ehci_pxa168_hc_driver = {
-	.description = hcd_name,
-	.product_desc = "Marvell PXA168 EHCI",
-	.hcd_priv_size = sizeof(struct pxa168_usb_drv_data),
-
-	/*
-	 * generic hardware linkage
-	 */
-	.irq = ehci_irq,
-	.flags = HCD_MEMORY | HCD_USB2,
-
-	/*
-	 * basic lifecycle operations
-	 */
-	.reset = ehci_pxa168_setup,
-	.start = ehci_run,
-	.stop = ehci_stop,
-	.shutdown = ehci_shutdown,
-
-	/*
-	 * managing i/o requests and associated device resources
-	 */
-	.urb_enqueue = ehci_urb_enqueue,
-	.urb_dequeue = ehci_urb_dequeue,
-	.endpoint_disable = ehci_endpoint_disable,
-	.endpoint_reset = ehci_endpoint_reset,
-
-	/*
-	 * scheduling support
-	 */
-	.get_frame_number = ehci_get_frame,
-
-	/*
-	 * root hub support
-	 */
-	.hub_status_data = ehci_hub_status_data,
-	.hub_control = ehci_hub_control,
-	.bus_suspend = ehci_bus_suspend,
-	.bus_resume = ehci_bus_resume,
-	.relinquish_port = ehci_relinquish_port,
-	.port_handed_over = ehci_port_handed_over,
-
-	.clear_tt_buffer_complete = ehci_clear_tt_buffer_complete,
-};
-
-static int pxa168_usb_phy_init(struct platform_device *pdev)
-{
-	struct resource *res;
-	void __iomem *usb_phy_reg_base;
-	struct pxa168_usb_pdata *pdata;
-	struct pxa168_usb_drv_data *drv_data;
-	struct usb_hcd *hcd = platform_get_drvdata(pdev);
-	unsigned long reg_val;
-	int pll_retry_cont = 10000, err = 0;
-
-	drv_data = (struct pxa168_usb_drv_data *)hcd->hcd_priv;
-	pdata = (struct pxa168_usb_pdata *)pdev->dev.platform_data;
-
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
-	if (!res) {
-		dev_err(&pdev->dev,
-			"Found HC with no PHY register addr. Check %s setup!\n",
-			dev_name(&pdev->dev));
-		return -ENODEV;
-	}
-
-	if (!request_mem_region(res->start, resource_size(res),
-				ehci_pxa168_hc_driver.description)) {
-		dev_dbg(&pdev->dev, "controller already in use\n");
-		return -EBUSY;
-	}
-
-	usb_phy_reg_base = ioremap(res->start, resource_size(res));
-	if (usb_phy_reg_base == NULL) {
-		dev_dbg(&pdev->dev, "error mapping memory\n");
-		err = -EFAULT;
-		goto err1;
-	}
-	drv_data->usb_phy_reg_base = usb_phy_reg_base;
-	drv_data->usb_phy_res = res;
-
-	/* If someone wants to init USB phy in board specific way */
-	if (pdata && pdata->phy_init)
-		return pdata->phy_init(usb_phy_reg_base);
-
-	/* Power up the PHY and PLL */
-	writel(readl(usb_phy_reg_base + USB_PHY_CTRL_REG) | 0x3,
-		usb_phy_reg_base + USB_PHY_CTRL_REG);
-
-	/* Configure PHY PLL */
-	reg_val = readl(usb_phy_reg_base + USB_PHY_PLL_REG) & ~(0x7e03ffff);
-	reg_val |= (VDD18_22 << PLLVDD18_SHIFT | VDD12_12 << PLLVDD12_SHIFT |
-		CALI12_11 << PLLCALI12_SHIFT | 3 << KVCO_SHIFT |
-		ICP_15 << ICP_SHIFT | 0xee << FBDIV_SHIFT | 0xb);
-	writel(reg_val, usb_phy_reg_base + USB_PHY_PLL_REG);
-
-	/* Make sure PHY PLL is ready */
-	while (!(readl(usb_phy_reg_base + USB_PHY_PLL_REG) & PLL_READY)) {
-		if (!(pll_retry_cont--)) {
-			dev_dbg(&pdev->dev, "USB PHY PLL not ready\n");
-			err = -EIO;
-			goto err2;
-		}
-	}
-
-	/* Toggle VCOCAL_START bit of U2PLL for PLL calibration */
-	udelay(200);
-	writel(readl(usb_phy_reg_base + USB_PHY_PLL_REG) | VCOCAL_START,
-		usb_phy_reg_base + USB_PHY_PLL_REG);
-	udelay(40);
-	writel(readl(usb_phy_reg_base + USB_PHY_PLL_REG) & ~VCOCAL_START,
-		usb_phy_reg_base + USB_PHY_PLL_REG);
-
-	/* Toggle REG_RCAL_START bit of U2PTX for impedance calibration */
-	udelay(400);
-	writel(readl(usb_phy_reg_base + USB_PHY_TX_REG) | REG_RCAL_START,
-		usb_phy_reg_base + USB_PHY_TX_REG);
-	udelay(40);
-	writel(readl(usb_phy_reg_base + USB_PHY_TX_REG) & ~REG_RCAL_START,
-		usb_phy_reg_base + USB_PHY_TX_REG);
-
-	/* Make sure PHY PLL is ready again */
-	pll_retry_cont = 0;
-	while (!(readl(usb_phy_reg_base + USB_PHY_PLL_REG) & PLL_READY)) {
-		if (!(pll_retry_cont--)) {
-			dev_dbg(&pdev->dev, "USB PHY PLL not ready\n");
-			err = -EIO;
-			goto err2;
-		}
-	}
-
-	return 0;
-err2:
-	iounmap(usb_phy_reg_base);
-err1:
-	release_mem_region(res->start, resource_size(res));
-	return err;
-}
-
-static int __devinit ehci_pxa168_drv_probe(struct platform_device *pdev)
-{
-	struct resource *res;
-	struct usb_hcd *hcd;
-	struct ehci_hcd *ehci;
-	struct pxa168_usb_drv_data *drv_data;
-	void __iomem *regs;
-	int irq, err = 0;
-
-	if (usb_disabled())
-		return -ENODEV;
-
-	pr_debug("Initializing pxa168-SoC USB Host Controller\n");
-
-	irq = platform_get_irq(pdev, 0);
-	if (irq <= 0) {
-		dev_err(&pdev->dev,
-			"Found HC with no IRQ. Check %s setup!\n",
-			dev_name(&pdev->dev));
-		err = -ENODEV;
-		goto err1;
-	}
-
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (!res) {
-		dev_err(&pdev->dev,
-			"Found HC with no register addr. Check %s setup!\n",
-			dev_name(&pdev->dev));
-		err = -ENODEV;
-		goto err1;
-	}
-
-	if (!request_mem_region(res->start, resource_size(res),
-				ehci_pxa168_hc_driver.description)) {
-		dev_dbg(&pdev->dev, "controller already in use\n");
-		err = -EBUSY;
-		goto err1;
-	}
-
-	regs = ioremap(res->start, resource_size(res));
-	if (regs == NULL) {
-		dev_dbg(&pdev->dev, "error mapping memory\n");
-		err = -EFAULT;
-		goto err2;
-	}
-
-	hcd = usb_create_hcd(&ehci_pxa168_hc_driver,
-			&pdev->dev, dev_name(&pdev->dev));
-	if (!hcd) {
-		err = -ENOMEM;
-		goto err3;
-	}
-
-	drv_data = (struct pxa168_usb_drv_data *)hcd->hcd_priv;
-
-	/* Enable USB clock */
-	drv_data->pxa168_usb_clk = clk_get(&pdev->dev, "PXA168-USBCLK");
-	if (IS_ERR(drv_data->pxa168_usb_clk)) {
-		dev_err(&pdev->dev, "Couldn't get USB clock\n");
-		err = PTR_ERR(drv_data->pxa168_usb_clk);
-		goto err4;
-	}
-	clk_enable(drv_data->pxa168_usb_clk);
-
-	err = pxa168_usb_phy_init(pdev);
-	if (err) {
-		dev_err(&pdev->dev, "USB PHY initialization failed\n");
-		goto err5;
-	}
-
-	hcd->rsrc_start = res->start;
-	hcd->rsrc_len = resource_size(res);
-	hcd->regs = regs;
-
-	ehci = hcd_to_ehci(hcd);
-	ehci->caps = hcd->regs + 0x100;
-	ehci->regs = hcd->regs + 0x100 +
-		HC_LENGTH(ehci, ehci_readl(ehci, &ehci->caps->hc_capbase));
-	ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params);
-	hcd->has_tt = 1;
-	ehci->sbrn = 0x20;
-
-	err = usb_add_hcd(hcd, irq, IRQF_SHARED | IRQF_DISABLED);
-	if (err)
-		goto err5;
-
-	return 0;
-
-err5:
-	clk_disable(drv_data->pxa168_usb_clk);
-	clk_put(drv_data->pxa168_usb_clk);
-err4:
-	usb_put_hcd(hcd);
-err3:
-	iounmap(regs);
-err2:
-	release_mem_region(res->start, resource_size(res));
-err1:
-	dev_err(&pdev->dev, "init %s fail, %d\n",
-		dev_name(&pdev->dev), err);
-
-	return err;
-}
-
-static int __exit ehci_pxa168_drv_remove(struct platform_device *pdev)
-{
-	struct usb_hcd *hcd = platform_get_drvdata(pdev);
-	struct pxa168_usb_drv_data *drv_data =
-		(struct pxa168_usb_drv_data *)hcd->hcd_priv;
-
-	usb_remove_hcd(hcd);
-
-	/* Power down PHY & PLL */
-	writel(readl(drv_data->usb_phy_reg_base + USB_PHY_CTRL_REG) & (~0x3),
-		drv_data->usb_phy_reg_base + USB_PHY_CTRL_REG);
-
-	clk_disable(drv_data->pxa168_usb_clk);
-	clk_put(drv_data->pxa168_usb_clk);
-
-	iounmap(hcd->regs);
-	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
-
-	iounmap(drv_data->usb_phy_reg_base);
-	release_mem_region(drv_data->usb_phy_res->start,
-			resource_size(drv_data->usb_phy_res));
-
-	usb_put_hcd(hcd);
-
-	return 0;
-}
-
-MODULE_ALIAS("platform:pxa168-ehci");
-
-static struct platform_driver ehci_pxa168_driver = {
-	.probe		= ehci_pxa168_drv_probe,
-	.remove		= __exit_p(ehci_pxa168_drv_remove),
-	.shutdown	= usb_hcd_platform_shutdown,
-	.driver.name	= "pxa168-ehci",
-};