Commit 0e245dba authored by Paul Gortmaker's avatar Paul Gortmaker

drivers/net: delete the 3Com 3c505/3c507 intel i825xx support

For those of us who were around in the early to mid 1990's, we
will remember that the i825xx ethernet support was not something
that was considered sufficiently vetted for 24/7 use.

Folks might be inclined to use *functional* ISA hardware on some
near expired P3 ISA machines for dedicated workhorse applications,
but the odds of using (and relying on) one of these old/experimental
drivers is essentially nil.  So lets remove them.
Signed-off-by: default avatarPaul Gortmaker <paul.gortmaker@windriver.com>
parent 168e06ae
...@@ -51,8 +51,6 @@ extern struct net_device *fmv18x_probe(int unit); ...@@ -51,8 +51,6 @@ extern struct net_device *fmv18x_probe(int unit);
extern struct net_device *eth16i_probe(int unit); extern struct net_device *eth16i_probe(int unit);
extern struct net_device *i82596_probe(int unit); extern struct net_device *i82596_probe(int unit);
extern struct net_device *ewrk3_probe(int unit); extern struct net_device *ewrk3_probe(int unit);
extern struct net_device *el16_probe(int unit);
extern struct net_device *elplus_probe(int unit);
extern struct net_device *e2100_probe(int unit); extern struct net_device *e2100_probe(int unit);
extern struct net_device *ni5010_probe(int unit); extern struct net_device *ni5010_probe(int unit);
extern struct net_device *ni52_probe(int unit); extern struct net_device *ni52_probe(int unit);
...@@ -164,12 +162,6 @@ static struct devprobe2 isa_probes[] __initdata = { ...@@ -164,12 +162,6 @@ static struct devprobe2 isa_probes[] __initdata = {
#if defined(CONFIG_MVME16x_NET) || defined(CONFIG_BVME6000_NET) /* Intel I82596 */ #if defined(CONFIG_MVME16x_NET) || defined(CONFIG_BVME6000_NET) /* Intel I82596 */
{i82596_probe, 0}, {i82596_probe, 0},
#endif #endif
#ifdef CONFIG_EL16 /* 3c507 */
{el16_probe, 0},
#endif
#ifdef CONFIG_ELPLUS /* 3c505 */
{elplus_probe, 0},
#endif
#ifdef CONFIG_NI5010 #ifdef CONFIG_NI5010
{ni5010_probe, 0}, {ni5010_probe, 0},
#endif #endif
......
/*
* Linux Ethernet device driver for the 3Com Etherlink Plus (3C505)
* By Craig Southeren, Juha Laiho and Philip Blundell
*
* 3c505.c This module implements an interface to the 3Com
* Etherlink Plus (3c505) Ethernet card. Linux device
* driver interface reverse engineered from the Linux 3C509
* device drivers. Some 3C505 information gleaned from
* the Crynwr packet driver. Still this driver would not
* be here without 3C505 technical reference provided by
* 3Com.
*
* $Id: 3c505.c,v 1.10 1996/04/16 13:06:27 phil Exp $
*
* Authors: Linux 3c505 device driver by
* Craig Southeren, <craigs@ineluki.apana.org.au>
* Final debugging by
* Andrew Tridgell, <tridge@nimbus.anu.edu.au>
* Auto irq/address, tuning, cleanup and v1.1.4+ kernel mods by
* Juha Laiho, <jlaiho@ichaos.nullnet.fi>
* Linux 3C509 driver by
* Donald Becker, <becker@super.org>
* (Now at <becker@scyld.com>)
* Crynwr packet driver by
* Krishnan Gopalan and Gregg Stefancik,
* Clemson University Engineering Computer Operations.
* Portions of the code have been adapted from the 3c505
* driver for NCSA Telnet by Bruce Orchard and later
* modified by Warren Van Houten and krus@diku.dk.
* 3C505 technical information provided by
* Terry Murphy, of 3Com Network Adapter Division
* Linux 1.3.0 changes by
* Alan Cox <Alan.Cox@linux.org>
* More debugging, DMA support, currently maintained by
* Philip Blundell <philb@gnu.org>
* Multicard/soft configurable dma channel/rev 2 hardware support
* by Christopher Collins <ccollins@pcug.org.au>
* Ethtool support (jgarzik), 11/17/2001
*/
#define DRV_NAME "3c505"
#define DRV_VERSION "1.10a"
/* Theory of operation:
*
* The 3c505 is quite an intelligent board. All communication with it is done
* by means of Primary Command Blocks (PCBs); these are transferred using PIO
* through the command register. The card has 256k of on-board RAM, which is
* used to buffer received packets. It might seem at first that more buffers
* are better, but in fact this isn't true. From my tests, it seems that
* more than about 10 buffers are unnecessary, and there is a noticeable
* performance hit in having more active on the card. So the majority of the
* card's memory isn't, in fact, used. Sadly, the card only has one transmit
* buffer and, short of loading our own firmware into it (which is what some
* drivers resort to) there's nothing we can do about this.
*
* We keep up to 4 "receive packet" commands active on the board at a time.
* When a packet comes in, so long as there is a receive command active, the
* board will send us a "packet received" PCB and then add the data for that
* packet to the DMA queue. If a DMA transfer is not already in progress, we
* set one up to start uploading the data. We have to maintain a list of
* backlogged receive packets, because the card may decide to tell us about
* a newly-arrived packet at any time, and we may not be able to start a DMA
* transfer immediately (ie one may already be going on). We can't NAK the
* PCB, because then it would throw the packet away.
*
* Trying to send a PCB to the card at the wrong moment seems to have bad
* effects. If we send it a transmit PCB while a receive DMA is happening,
* it will just NAK the PCB and so we will have wasted our time. Worse, it
* sometimes seems to interrupt the transfer. The majority of the low-level
* code is protected by one huge semaphore -- "busy" -- which is set whenever
* it probably isn't safe to do anything to the card. The receive routine
* must gain a lock on "busy" before it can start a DMA transfer, and the
* transmit routine must gain a lock before it sends the first PCB to the card.
* The send_pcb() routine also has an internal semaphore to protect it against
* being re-entered (which would be disastrous) -- this is needed because
* several things can happen asynchronously (re-priming the receiver and
* asking the card for statistics, for example). send_pcb() will also refuse
* to talk to the card at all if a DMA upload is happening. The higher-level
* networking code will reschedule a later retry if some part of the driver
* is blocked. In practice, this doesn't seem to happen very often.
*/
/* This driver may now work with revision 2.x hardware, since all the read
* operations on the HCR have been removed (we now keep our own softcopy).
* But I don't have an old card to test it on.
*
* This has had the bad effect that the autoprobe routine is now a bit
* less friendly to other devices. However, it was never very good.
* before, so I doubt it will hurt anybody.
*/
/* The driver is a mess. I took Craig's and Juha's code, and hacked it firstly
* to make it more reliable, and secondly to add DMA mode. Many things could
* probably be done better; the concurrency protection is particularly awful.
*/
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/string.h>
#include <linux/interrupt.h>
#include <linux/errno.h>
#include <linux/in.h>
#include <linux/ioport.h>
#include <linux/spinlock.h>
#include <linux/ethtool.h>
#include <linux/delay.h>
#include <linux/bitops.h>
#include <linux/gfp.h>
#include <asm/uaccess.h>
#include <asm/io.h>
#include <asm/dma.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/skbuff.h>
#include <linux/init.h>
#include "3c505.h"
/*********************************************************
*
* define debug messages here as common strings to reduce space
*
*********************************************************/
#define timeout_msg "*** timeout at %s:%s (line %d) ***\n"
#define TIMEOUT_MSG(lineno) \
pr_notice(timeout_msg, __FILE__, __func__, (lineno))
#define invalid_pcb_msg "*** invalid pcb length %d at %s:%s (line %d) ***\n"
#define INVALID_PCB_MSG(len) \
pr_notice(invalid_pcb_msg, (len), __FILE__, __func__, __LINE__)
#define search_msg "%s: Looking for 3c505 adapter at address %#x..."
#define stilllooking_msg "still looking..."
#define found_msg "found.\n"
#define notfound_msg "not found (reason = %d)\n"
#define couldnot_msg "%s: 3c505 not found\n"
/*********************************************************
*
* various other debug stuff
*
*********************************************************/
#ifdef ELP_DEBUG
static int elp_debug = ELP_DEBUG;
#else
static int elp_debug;
#endif
#define debug elp_debug
/*
* 0 = no messages (well, some)
* 1 = messages when high level commands performed
* 2 = messages when low level commands performed
* 3 = messages when interrupts received
*/
/*****************************************************************
*
* List of I/O-addresses we try to auto-sense
* Last element MUST BE 0!
*****************************************************************/
static int addr_list[] __initdata = {0x300, 0x280, 0x310, 0};
/* Dma Memory related stuff */
static unsigned long dma_mem_alloc(int size)
{
int order = get_order(size);
return __get_dma_pages(GFP_KERNEL, order);
}
/*****************************************************************
*
* Functions for I/O (note the inline !)
*
*****************************************************************/
static inline unsigned char inb_status(unsigned int base_addr)
{
return inb(base_addr + PORT_STATUS);
}
static inline int inb_command(unsigned int base_addr)
{
return inb(base_addr + PORT_COMMAND);
}
static inline void outb_control(unsigned char val, struct net_device *dev)
{
outb(val, dev->base_addr + PORT_CONTROL);
((elp_device *)(netdev_priv(dev)))->hcr_val = val;
}
#define HCR_VAL(x) (((elp_device *)(netdev_priv(x)))->hcr_val)
static inline void outb_command(unsigned char val, unsigned int base_addr)
{
outb(val, base_addr + PORT_COMMAND);
}
static inline unsigned int backlog_next(unsigned int n)
{
return (n + 1) % BACKLOG_SIZE;
}
/*****************************************************************
*
* useful functions for accessing the adapter
*
*****************************************************************/
/*
* use this routine when accessing the ASF bits as they are
* changed asynchronously by the adapter
*/
/* get adapter PCB status */
#define GET_ASF(addr) \
(get_status(addr)&ASF_PCB_MASK)
static inline int get_status(unsigned int base_addr)
{
unsigned long timeout = jiffies + 10*HZ/100;
register int stat1;
do {
stat1 = inb_status(base_addr);
} while (stat1 != inb_status(base_addr) && time_before(jiffies, timeout));
if (time_after_eq(jiffies, timeout))
TIMEOUT_MSG(__LINE__);
return stat1;
}
static inline void set_hsf(struct net_device *dev, int hsf)
{
elp_device *adapter = netdev_priv(dev);
unsigned long flags;
spin_lock_irqsave(&adapter->lock, flags);
outb_control((HCR_VAL(dev) & ~HSF_PCB_MASK) | hsf, dev);
spin_unlock_irqrestore(&adapter->lock, flags);
}
static bool start_receive(struct net_device *, pcb_struct *);
static inline void adapter_reset(struct net_device *dev)
{
unsigned long timeout;
elp_device *adapter = netdev_priv(dev);
unsigned char orig_hcr = adapter->hcr_val;
outb_control(0, dev);
if (inb_status(dev->base_addr) & ACRF) {
do {
inb_command(dev->base_addr);
timeout = jiffies + 2*HZ/100;
while (time_before_eq(jiffies, timeout) && !(inb_status(dev->base_addr) & ACRF));
} while (inb_status(dev->base_addr) & ACRF);
set_hsf(dev, HSF_PCB_NAK);
}
outb_control(adapter->hcr_val | ATTN | DIR, dev);
mdelay(10);
outb_control(adapter->hcr_val & ~ATTN, dev);
mdelay(10);
outb_control(adapter->hcr_val | FLSH, dev);
mdelay(10);
outb_control(adapter->hcr_val & ~FLSH, dev);
mdelay(10);
outb_control(orig_hcr, dev);
if (!start_receive(dev, &adapter->tx_pcb))
pr_err("%s: start receive command failed\n", dev->name);
}
/* Check to make sure that a DMA transfer hasn't timed out. This should
* never happen in theory, but seems to occur occasionally if the card gets
* prodded at the wrong time.
*/
static inline void check_3c505_dma(struct net_device *dev)
{
elp_device *adapter = netdev_priv(dev);
if (adapter->dmaing && time_after(jiffies, adapter->current_dma.start_time + 10)) {
unsigned long flags, f;
pr_err("%s: DMA %s timed out, %d bytes left\n", dev->name,
adapter->current_dma.direction ? "download" : "upload",
get_dma_residue(dev->dma));
spin_lock_irqsave(&adapter->lock, flags);
adapter->dmaing = 0;
adapter->busy = 0;
f=claim_dma_lock();
disable_dma(dev->dma);
release_dma_lock(f);
if (adapter->rx_active)
adapter->rx_active--;
outb_control(adapter->hcr_val & ~(DMAE | TCEN | DIR), dev);
spin_unlock_irqrestore(&adapter->lock, flags);
}
}
/* Primitive functions used by send_pcb() */
static inline bool send_pcb_slow(unsigned int base_addr, unsigned char byte)
{
unsigned long timeout;
outb_command(byte, base_addr);
for (timeout = jiffies + 5*HZ/100; time_before(jiffies, timeout);) {
if (inb_status(base_addr) & HCRE)
return false;
}
pr_warning("3c505: send_pcb_slow timed out\n");
return true;
}
static inline bool send_pcb_fast(unsigned int base_addr, unsigned char byte)
{
unsigned int timeout;
outb_command(byte, base_addr);
for (timeout = 0; timeout < 40000; timeout++) {
if (inb_status(base_addr) & HCRE)
return false;
}
pr_warning("3c505: send_pcb_fast timed out\n");
return true;
}
/* Check to see if the receiver needs restarting, and kick it if so */
static inline void prime_rx(struct net_device *dev)
{
elp_device *adapter = netdev_priv(dev);
while (adapter->rx_active < ELP_RX_PCBS && netif_running(dev)) {
if (!start_receive(dev, &adapter->itx_pcb))
break;
}
}
/*****************************************************************
*
* send_pcb
* Send a PCB to the adapter.
*
* output byte to command reg --<--+
* wait until HCRE is non zero |
* loop until all bytes sent -->--+
* set HSF1 and HSF2 to 1
* output pcb length
* wait until ASF give ACK or NAK
* set HSF1 and HSF2 to 0
*
*****************************************************************/
/* This can be quite slow -- the adapter is allowed to take up to 40ms
* to respond to the initial interrupt.
*
* We run initially with interrupts turned on, but with a semaphore set
* so that nobody tries to re-enter this code. Once the first byte has
* gone through, we turn interrupts off and then send the others (the
* timeout is reduced to 500us).
*/
static bool send_pcb(struct net_device *dev, pcb_struct * pcb)
{
int i;
unsigned long timeout;
elp_device *adapter = netdev_priv(dev);
unsigned long flags;
check_3c505_dma(dev);
if (adapter->dmaing && adapter->current_dma.direction == 0)
return false;
/* Avoid contention */
if (test_and_set_bit(1, &adapter->send_pcb_semaphore)) {
if (elp_debug >= 3) {
pr_debug("%s: send_pcb entered while threaded\n", dev->name);
}
return false;
}
/*
* load each byte into the command register and
* wait for the HCRE bit to indicate the adapter
* had read the byte
*/
set_hsf(dev, 0);
if (send_pcb_slow(dev->base_addr, pcb->command))
goto abort;
spin_lock_irqsave(&adapter->lock, flags);
if (send_pcb_fast(dev->base_addr, pcb->length))
goto sti_abort;
for (i = 0; i < pcb->length; i++) {
if (send_pcb_fast(dev->base_addr, pcb->data.raw[i]))
goto sti_abort;
}
outb_control(adapter->hcr_val | 3, dev); /* signal end of PCB */
outb_command(2 + pcb->length, dev->base_addr);
/* now wait for the acknowledgement */
spin_unlock_irqrestore(&adapter->lock, flags);
for (timeout = jiffies + 5*HZ/100; time_before(jiffies, timeout);) {
switch (GET_ASF(dev->base_addr)) {
case ASF_PCB_ACK:
adapter->send_pcb_semaphore = 0;
return true;
case ASF_PCB_NAK:
#ifdef ELP_DEBUG
pr_debug("%s: send_pcb got NAK\n", dev->name);
#endif
goto abort;
}
}
if (elp_debug >= 1)
pr_debug("%s: timeout waiting for PCB acknowledge (status %02x)\n",
dev->name, inb_status(dev->base_addr));
goto abort;
sti_abort:
spin_unlock_irqrestore(&adapter->lock, flags);
abort:
adapter->send_pcb_semaphore = 0;
return false;
}
/*****************************************************************
*
* receive_pcb
* Read a PCB from the adapter
*
* wait for ACRF to be non-zero ---<---+
* input a byte |
* if ASF1 and ASF2 were not both one |
* before byte was read, loop --->---+
* set HSF1 and HSF2 for ack
*
*****************************************************************/
static bool receive_pcb(struct net_device *dev, pcb_struct * pcb)
{
int i, j;
int total_length;
int stat;
unsigned long timeout;
unsigned long flags;
elp_device *adapter = netdev_priv(dev);
set_hsf(dev, 0);
/* get the command code */
timeout = jiffies + 2*HZ/100;
while (((stat = get_status(dev->base_addr)) & ACRF) == 0 && time_before(jiffies, timeout));
if (time_after_eq(jiffies, timeout)) {
TIMEOUT_MSG(__LINE__);
return false;
}
pcb->command = inb_command(dev->base_addr);
/* read the data length */
timeout = jiffies + 3*HZ/100;
while (((stat = get_status(dev->base_addr)) & ACRF) == 0 && time_before(jiffies, timeout));
if (time_after_eq(jiffies, timeout)) {
TIMEOUT_MSG(__LINE__);
pr_info("%s: status %02x\n", dev->name, stat);
return false;
}
pcb->length = inb_command(dev->base_addr);
if (pcb->length > MAX_PCB_DATA) {
INVALID_PCB_MSG(pcb->length);
adapter_reset(dev);
return false;
}
/* read the data */
spin_lock_irqsave(&adapter->lock, flags);
for (i = 0; i < MAX_PCB_DATA; i++) {
for (j = 0; j < 20000; j++) {
stat = get_status(dev->base_addr);
if (stat & ACRF)
break;
}
pcb->data.raw[i] = inb_command(dev->base_addr);
if ((stat & ASF_PCB_MASK) == ASF_PCB_END || j >= 20000)
break;
}
spin_unlock_irqrestore(&adapter->lock, flags);
if (i >= MAX_PCB_DATA) {
INVALID_PCB_MSG(i);
return false;
}
if (j >= 20000) {
TIMEOUT_MSG(__LINE__);
return false;
}
/* the last "data" byte was really the length! */
total_length = pcb->data.raw[i];
/* safety check total length vs data length */
if (total_length != (pcb->length + 2)) {
if (elp_debug >= 2)
pr_warning("%s: mangled PCB received\n", dev->name);
set_hsf(dev, HSF_PCB_NAK);
return false;
}
if (pcb->command == CMD_RECEIVE_PACKET_COMPLETE) {
if (test_and_set_bit(0, (void *) &adapter->busy)) {
if (backlog_next(adapter->rx_backlog.in) == adapter->rx_backlog.out) {
set_hsf(dev, HSF_PCB_NAK);
pr_warning("%s: PCB rejected, transfer in progress and backlog full\n", dev->name);
pcb->command = 0;
return true;
} else {
pcb->command = 0xff;
}
}
}
set_hsf(dev, HSF_PCB_ACK);
return true;
}
/******************************************************
*
* queue a receive command on the adapter so we will get an
* interrupt when a packet is received.
*
******************************************************/
static bool start_receive(struct net_device *dev, pcb_struct * tx_pcb)
{
bool status;
elp_device *adapter = netdev_priv(dev);
if (elp_debug >= 3)
pr_debug("%s: restarting receiver\n", dev->name);
tx_pcb->command = CMD_RECEIVE_PACKET;
tx_pcb->length = sizeof(struct Rcv_pkt);
tx_pcb->data.rcv_pkt.buf_seg
= tx_pcb->data.rcv_pkt.buf_ofs = 0; /* Unused */
tx_pcb->data.rcv_pkt.buf_len = 1600;
tx_pcb->data.rcv_pkt.timeout = 0; /* set timeout to zero */
status = send_pcb(dev, tx_pcb);
if (status)
adapter->rx_active++;
return status;
}
/******************************************************
*
* extract a packet from the adapter
* this routine is only called from within the interrupt
* service routine, so no cli/sti calls are needed
* note that the length is always assumed to be even
*
******************************************************/
static void receive_packet(struct net_device *dev, int len)
{
int rlen;
elp_device *adapter = netdev_priv(dev);
void *target;
struct sk_buff *skb;
unsigned long flags;
rlen = (len + 1) & ~1;
skb = netdev_alloc_skb(dev, rlen + 2);
if (!skb) {
pr_warning("%s: memory squeeze, dropping packet\n", dev->name);
target = adapter->dma_buffer;
adapter->current_dma.target = NULL;
/* FIXME: stats */
return;
}
skb_reserve(skb, 2);
target = skb_put(skb, rlen);
if ((unsigned long)(target + rlen) >= MAX_DMA_ADDRESS) {
adapter->current_dma.target = target;
target = adapter->dma_buffer;
} else {
adapter->current_dma.target = NULL;
}
/* if this happens, we die */
if (test_and_set_bit(0, (void *) &adapter->dmaing))
pr_err("%s: rx blocked, DMA in progress, dir %d\n",
dev->name, adapter->current_dma.direction);
adapter->current_dma.direction = 0;
adapter->current_dma.length = rlen;
adapter->current_dma.skb = skb;
adapter->current_dma.start_time = jiffies;
outb_control(adapter->hcr_val | DIR | TCEN | DMAE, dev);
flags=claim_dma_lock();
disable_dma(dev->dma);
clear_dma_ff(dev->dma);
set_dma_mode(dev->dma, 0x04); /* dma read */
set_dma_addr(dev->dma, isa_virt_to_bus(target));
set_dma_count(dev->dma, rlen);
enable_dma(dev->dma);
release_dma_lock(flags);
if (elp_debug >= 3) {
pr_debug("%s: rx DMA transfer started\n", dev->name);
}
if (adapter->rx_active)
adapter->rx_active--;
if (!adapter->busy)
pr_warning("%s: receive_packet called, busy not set.\n", dev->name);
}
/******************************************************
*
* interrupt handler
*
******************************************************/
static irqreturn_t elp_interrupt(int irq, void *dev_id)
{
int len;
int dlen;
int icount = 0;
struct net_device *dev = dev_id;
elp_device *adapter = netdev_priv(dev);
unsigned long timeout;
spin_lock(&adapter->lock);
do {
/*
* has a DMA transfer finished?
*/
if (inb_status(dev->base_addr) & DONE) {
if (!adapter->dmaing)
pr_warning("%s: phantom DMA completed\n", dev->name);
if (elp_debug >= 3)
pr_debug("%s: %s DMA complete, status %02x\n", dev->name,
adapter->current_dma.direction ? "tx" : "rx",
inb_status(dev->base_addr));
outb_control(adapter->hcr_val & ~(DMAE | TCEN | DIR), dev);
if (adapter->current_dma.direction) {
dev_kfree_skb_irq(adapter->current_dma.skb);
} else {
struct sk_buff *skb = adapter->current_dma.skb;
if (skb) {
if (adapter->current_dma.target) {
/* have already done the skb_put() */
memcpy(adapter->current_dma.target, adapter->dma_buffer, adapter->current_dma.length);
}
skb->protocol = eth_type_trans(skb,dev);
dev->stats.rx_bytes += skb->len;
netif_rx(skb);
}
}
adapter->dmaing = 0;
if (adapter->rx_backlog.in != adapter->rx_backlog.out) {
int t = adapter->rx_backlog.length[adapter->rx_backlog.out];
adapter->rx_backlog.out = backlog_next(adapter->rx_backlog.out);
if (elp_debug >= 2)
pr_debug("%s: receiving backlogged packet (%d)\n", dev->name, t);
receive_packet(dev, t);
} else {
adapter->busy = 0;
}
} else {
/* has one timed out? */
check_3c505_dma(dev);
}
/*
* receive a PCB from the adapter
*/
timeout = jiffies + 3*HZ/100;
while ((inb_status(dev->base_addr) & ACRF) != 0 && time_before(jiffies, timeout)) {
if (receive_pcb(dev, &adapter->irx_pcb)) {
switch (adapter->irx_pcb.command)
{
case 0:
break;
/*
* received a packet - this must be handled fast
*/
case 0xff:
case CMD_RECEIVE_PACKET_COMPLETE:
/* if the device isn't open, don't pass packets up the stack */
if (!netif_running(dev))
break;
len = adapter->irx_pcb.data.rcv_resp.pkt_len;
dlen = adapter->irx_pcb.data.rcv_resp.buf_len;
if (adapter->irx_pcb.data.rcv_resp.timeout != 0) {
pr_err("%s: interrupt - packet not received correctly\n", dev->name);
} else {
if (elp_debug >= 3) {
pr_debug("%s: interrupt - packet received of length %i (%i)\n",
dev->name, len, dlen);
}
if (adapter->irx_pcb.command == 0xff) {
if (elp_debug >= 2)
pr_debug("%s: adding packet to backlog (len = %d)\n",
dev->name, dlen);
adapter->rx_backlog.length[adapter->rx_backlog.in] = dlen;
adapter->rx_backlog.in = backlog_next(adapter->rx_backlog.in);
} else {
receive_packet(dev, dlen);
}
if (elp_debug >= 3)
pr_debug("%s: packet received\n", dev->name);
}
break;
/*
* 82586 configured correctly
*/
case CMD_CONFIGURE_82586_RESPONSE:
adapter->got[CMD_CONFIGURE_82586] = 1;
if (elp_debug >= 3)
pr_debug("%s: interrupt - configure response received\n", dev->name);
break;
/*
* Adapter memory configuration
*/
case CMD_CONFIGURE_ADAPTER_RESPONSE:
adapter->got[CMD_CONFIGURE_ADAPTER_MEMORY] = 1;
if (elp_debug >= 3)
pr_debug("%s: Adapter memory configuration %s.\n", dev->name,
adapter->irx_pcb.data.failed ? "failed" : "succeeded");
break;
/*
* Multicast list loading
*/
case CMD_LOAD_MULTICAST_RESPONSE:
adapter->got[CMD_LOAD_MULTICAST_LIST] = 1;
if (elp_debug >= 3)
pr_debug("%s: Multicast address list loading %s.\n", dev->name,
adapter->irx_pcb.data.failed ? "failed" : "succeeded");
break;
/*
* Station address setting
*/
case CMD_SET_ADDRESS_RESPONSE:
adapter->got[CMD_SET_STATION_ADDRESS] = 1;
if (elp_debug >= 3)
pr_debug("%s: Ethernet address setting %s.\n", dev->name,
adapter->irx_pcb.data.failed ? "failed" : "succeeded");
break;
/*
* received board statistics
*/
case CMD_NETWORK_STATISTICS_RESPONSE:
dev->stats.rx_packets += adapter->irx_pcb.data.netstat.tot_recv;
dev->stats.tx_packets += adapter->irx_pcb.data.netstat.tot_xmit;
dev->stats.rx_crc_errors += adapter->irx_pcb.data.netstat.err_CRC;
dev->stats.rx_frame_errors += adapter->irx_pcb.data.netstat.err_align;
dev->stats.rx_fifo_errors += adapter->irx_pcb.data.netstat.err_ovrrun;
dev->stats.rx_over_errors += adapter->irx_pcb.data.netstat.err_res;
adapter->got[CMD_NETWORK_STATISTICS] = 1;
if (elp_debug >= 3)
pr_debug("%s: interrupt - statistics response received\n", dev->name);
break;
/*
* sent a packet
*/
case CMD_TRANSMIT_PACKET_COMPLETE:
if (elp_debug >= 3)
pr_debug("%s: interrupt - packet sent\n", dev->name);
if (!netif_running(dev))
break;
switch (adapter->irx_pcb.data.xmit_resp.c_stat) {
case 0xffff:
dev->stats.tx_aborted_errors++;
pr_info("%s: transmit timed out, network cable problem?\n", dev->name);
break;
case 0xfffe:
dev->stats.tx_fifo_errors++;
pr_info("%s: transmit timed out, FIFO underrun\n", dev->name);
break;
}
netif_wake_queue(dev);
break;
/*
* some unknown PCB
*/
default:
pr_debug("%s: unknown PCB received - %2.2x\n",
dev->name, adapter->irx_pcb.command);
break;
}
} else {
pr_warning("%s: failed to read PCB on interrupt\n", dev->name);
adapter_reset(dev);
}
}
} while (icount++ < 5 && (inb_status(dev->base_addr) & (ACRF | DONE)));
prime_rx(dev);
/*
* indicate no longer in interrupt routine
*/
spin_unlock(&adapter->lock);
return IRQ_HANDLED;
}
/******************************************************
*
* open the board
*
******************************************************/
static int elp_open(struct net_device *dev)
{
elp_device *adapter = netdev_priv(dev);
int retval;
if (elp_debug >= 3)
pr_debug("%s: request to open device\n", dev->name);
/*
* make sure we actually found the device
*/
if (adapter == NULL) {
pr_err("%s: Opening a non-existent physical device\n", dev->name);
return -EAGAIN;
}
/*
* disable interrupts on the board
*/
outb_control(0, dev);
/*
* clear any pending interrupts
*/
inb_command(dev->base_addr);
adapter_reset(dev);
/*
* no receive PCBs active
*/
adapter->rx_active = 0;
adapter->busy = 0;
adapter->send_pcb_semaphore = 0;
adapter->rx_backlog.in = 0;
adapter->rx_backlog.out = 0;
spin_lock_init(&adapter->lock);
/*
* install our interrupt service routine
*/
if ((retval = request_irq(dev->irq, elp_interrupt, 0, dev->name, dev))) {
pr_err("%s: could not allocate IRQ%d\n", dev->name, dev->irq);
return retval;
}
if ((retval = request_dma(dev->dma, dev->name))) {
free_irq(dev->irq, dev);
pr_err("%s: could not allocate DMA%d channel\n", dev->name, dev->dma);
return retval;
}
adapter->dma_buffer = (void *) dma_mem_alloc(DMA_BUFFER_SIZE);
if (!adapter->dma_buffer) {
pr_err("%s: could not allocate DMA buffer\n", dev->name);
free_dma(dev->dma);
free_irq(dev->irq, dev);
return -ENOMEM;
}
adapter->dmaing = 0;
/*
* enable interrupts on the board
*/
outb_control(CMDE, dev);
/*
* configure adapter memory: we need 10 multicast addresses, default==0
*/
if (elp_debug >= 3)
pr_debug("%s: sending 3c505 memory configuration command\n", dev->name);
adapter->tx_pcb.command = CMD_CONFIGURE_ADAPTER_MEMORY;
adapter->tx_pcb.data.memconf.cmd_q = 10;
adapter->tx_pcb.data.memconf.rcv_q = 20;
adapter->tx_pcb.data.memconf.mcast = 10;
adapter->tx_pcb.data.memconf.frame = 20;
adapter->tx_pcb.data.memconf.rcv_b = 20;
adapter->tx_pcb.data.memconf.progs = 0;
adapter->tx_pcb.length = sizeof(struct Memconf);
adapter->got[CMD_CONFIGURE_ADAPTER_MEMORY] = 0;
if (!send_pcb(dev, &adapter->tx_pcb))
pr_err("%s: couldn't send memory configuration command\n", dev->name);
else {
unsigned long timeout = jiffies + TIMEOUT;
while (adapter->got[CMD_CONFIGURE_ADAPTER_MEMORY] == 0 && time_before(jiffies, timeout));
if (time_after_eq(jiffies, timeout))
TIMEOUT_MSG(__LINE__);
}
/*
* configure adapter to receive broadcast messages and wait for response
*/
if (elp_debug >= 3)
pr_debug("%s: sending 82586 configure command\n", dev->name);
adapter->tx_pcb.command = CMD_CONFIGURE_82586;
adapter->tx_pcb.data.configure = NO_LOOPBACK | RECV_BROAD;
adapter->tx_pcb.length = 2;
adapter->got[CMD_CONFIGURE_82586] = 0;
if (!send_pcb(dev, &adapter->tx_pcb))
pr_err("%s: couldn't send 82586 configure command\n", dev->name);
else {
unsigned long timeout = jiffies + TIMEOUT;
while (adapter->got[CMD_CONFIGURE_82586] == 0 && time_before(jiffies, timeout));
if (time_after_eq(jiffies, timeout))
TIMEOUT_MSG(__LINE__);
}
/* enable burst-mode DMA */
/* outb(0x1, dev->base_addr + PORT_AUXDMA); */
/*
* queue receive commands to provide buffering
*/
prime_rx(dev);
if (elp_debug >= 3)
pr_debug("%s: %d receive PCBs active\n", dev->name, adapter->rx_active);
/*
* device is now officially open!
*/
netif_start_queue(dev);
return 0;
}
/******************************************************
*
* send a packet to the adapter
*
******************************************************/
static netdev_tx_t send_packet(struct net_device *dev, struct sk_buff *skb)
{
elp_device *adapter = netdev_priv(dev);
unsigned long target;
unsigned long flags;
/*
* make sure the length is even and no shorter than 60 bytes
*/
unsigned int nlen = (((skb->len < 60) ? 60 : skb->len) + 1) & (~1);
if (test_and_set_bit(0, (void *) &adapter->busy)) {
if (elp_debug >= 2)
pr_debug("%s: transmit blocked\n", dev->name);
return false;
}
dev->stats.tx_bytes += nlen;
/*
* send the adapter a transmit packet command. Ignore segment and offset
* and make sure the length is even
*/
adapter->tx_pcb.command = CMD_TRANSMIT_PACKET;
adapter->tx_pcb.length = sizeof(struct Xmit_pkt);
adapter->tx_pcb.data.xmit_pkt.buf_ofs
= adapter->tx_pcb.data.xmit_pkt.buf_seg = 0; /* Unused */
adapter->tx_pcb.data.xmit_pkt.pkt_len = nlen;
if (!send_pcb(dev, &adapter->tx_pcb)) {
adapter->busy = 0;
return false;
}
/* if this happens, we die */
if (test_and_set_bit(0, (void *) &adapter->dmaing))
pr_debug("%s: tx: DMA %d in progress\n", dev->name, adapter->current_dma.direction);
adapter->current_dma.direction = 1;
adapter->current_dma.start_time = jiffies;
if ((unsigned long)(skb->data + nlen) >= MAX_DMA_ADDRESS || nlen != skb->len) {
skb_copy_from_linear_data(skb, adapter->dma_buffer, nlen);
memset(adapter->dma_buffer+skb->len, 0, nlen-skb->len);
target = isa_virt_to_bus(adapter->dma_buffer);
}
else {
target = isa_virt_to_bus(skb->data);
}
adapter->current_dma.skb = skb;
flags=claim_dma_lock();
disable_dma(dev->dma);
clear_dma_ff(dev->dma);
set_dma_mode(dev->dma, 0x48); /* dma memory -> io */
set_dma_addr(dev->dma, target);
set_dma_count(dev->dma, nlen);
outb_control(adapter->hcr_val | DMAE | TCEN, dev);
enable_dma(dev->dma);
release_dma_lock(flags);
if (elp_debug >= 3)
pr_debug("%s: DMA transfer started\n", dev->name);
return true;
}
/*
* The upper layer thinks we timed out
*/
static void elp_timeout(struct net_device *dev)
{
int stat;
stat = inb_status(dev->base_addr);
pr_warning("%s: transmit timed out, lost %s?\n", dev->name,
(stat & ACRF) ? "interrupt" : "command");
if (elp_debug >= 1)
pr_debug("%s: status %#02x\n", dev->name, stat);
dev->trans_start = jiffies; /* prevent tx timeout */
dev->stats.tx_dropped++;
netif_wake_queue(dev);
}
/******************************************************
*
* start the transmitter
* return 0 if sent OK, else return 1
*
******************************************************/
static netdev_tx_t elp_start_xmit(struct sk_buff *skb, struct net_device *dev)
{
unsigned long flags;
elp_device *adapter = netdev_priv(dev);
spin_lock_irqsave(&adapter->lock, flags);
check_3c505_dma(dev);
if (elp_debug >= 3)
pr_debug("%s: request to send packet of length %d\n", dev->name, (int) skb->len);
netif_stop_queue(dev);
/*
* send the packet at skb->data for skb->len
*/
if (!send_packet(dev, skb)) {
if (elp_debug >= 2) {
pr_debug("%s: failed to transmit packet\n", dev->name);
}
spin_unlock_irqrestore(&adapter->lock, flags);
return NETDEV_TX_BUSY;
}
if (elp_debug >= 3)
pr_debug("%s: packet of length %d sent\n", dev->name, (int) skb->len);
prime_rx(dev);
spin_unlock_irqrestore(&adapter->lock, flags);
netif_start_queue(dev);
return NETDEV_TX_OK;
}
/******************************************************
*
* return statistics on the board
*
******************************************************/
static struct net_device_stats *elp_get_stats(struct net_device *dev)
{
elp_device *adapter = netdev_priv(dev);
if (elp_debug >= 3)
pr_debug("%s: request for stats\n", dev->name);
/* If the device is closed, just return the latest stats we have,
- we cannot ask from the adapter without interrupts */
if (!netif_running(dev))
return &dev->stats;
/* send a get statistics command to the board */
adapter->tx_pcb.command = CMD_NETWORK_STATISTICS;
adapter->tx_pcb.length = 0;
adapter->got[CMD_NETWORK_STATISTICS] = 0;
if (!send_pcb(dev, &adapter->tx_pcb))
pr_err("%s: couldn't send get statistics command\n", dev->name);
else {
unsigned long timeout = jiffies + TIMEOUT;
while (adapter->got[CMD_NETWORK_STATISTICS] == 0 && time_before(jiffies, timeout));
if (time_after_eq(jiffies, timeout)) {
TIMEOUT_MSG(__LINE__);
return &dev->stats;
}
}
/* statistics are now up to date */
return &dev->stats;
}
static void netdev_get_drvinfo(struct net_device *dev,
struct ethtool_drvinfo *info)
{
strlcpy(info->driver, DRV_NAME, sizeof(info->driver));
strlcpy(info->version, DRV_VERSION, sizeof(info->version));
snprintf(info->bus_info, sizeof(info->bus_info), "ISA 0x%lx",
dev->base_addr);
}
static u32 netdev_get_msglevel(struct net_device *dev)
{
return debug;
}
static void netdev_set_msglevel(struct net_device *dev, u32 level)
{
debug = level;
}
static const struct ethtool_ops netdev_ethtool_ops = {
.get_drvinfo = netdev_get_drvinfo,
.get_msglevel = netdev_get_msglevel,
.set_msglevel = netdev_set_msglevel,
};
/******************************************************
*
* close the board
*
******************************************************/
static int elp_close(struct net_device *dev)
{
elp_device *adapter = netdev_priv(dev);
if (elp_debug >= 3)
pr_debug("%s: request to close device\n", dev->name);
netif_stop_queue(dev);
/* Someone may request the device statistic information even when
* the interface is closed. The following will update the statistics
* structure in the driver, so we'll be able to give current statistics.
*/
(void) elp_get_stats(dev);
/*
* disable interrupts on the board
*/
outb_control(0, dev);
/*
* release the IRQ
*/
free_irq(dev->irq, dev);
free_dma(dev->dma);
free_pages((unsigned long) adapter->dma_buffer, get_order(DMA_BUFFER_SIZE));
return 0;
}
/************************************************************
*
* Set multicast list
* num_addrs==0: clear mc_list
* num_addrs==-1: set promiscuous mode
* num_addrs>0: set mc_list
*
************************************************************/
static void elp_set_mc_list(struct net_device *dev)
{
elp_device *adapter = netdev_priv(dev);
struct netdev_hw_addr *ha;
int i;
unsigned long flags;
if (elp_debug >= 3)
pr_debug("%s: request to set multicast list\n", dev->name);
spin_lock_irqsave(&adapter->lock, flags);
if (!(dev->flags & (IFF_PROMISC | IFF_ALLMULTI))) {
/* send a "load multicast list" command to the board, max 10 addrs/cmd */
/* if num_addrs==0 the list will be cleared */
adapter->tx_pcb.command = CMD_LOAD_MULTICAST_LIST;
adapter->tx_pcb.length = 6 * netdev_mc_count(dev);
i = 0;
netdev_for_each_mc_addr(ha, dev)
memcpy(adapter->tx_pcb.data.multicast[i++],
ha->addr, 6);
adapter->got[CMD_LOAD_MULTICAST_LIST] = 0;
if (!send_pcb(dev, &adapter->tx_pcb))
pr_err("%s: couldn't send set_multicast command\n", dev->name);
else {
unsigned long timeout = jiffies + TIMEOUT;
while (adapter->got[CMD_LOAD_MULTICAST_LIST] == 0 && time_before(jiffies, timeout));
if (time_after_eq(jiffies, timeout)) {
TIMEOUT_MSG(__LINE__);
}
}
if (!netdev_mc_empty(dev))
adapter->tx_pcb.data.configure = NO_LOOPBACK | RECV_BROAD | RECV_MULTI;
else /* num_addrs == 0 */
adapter->tx_pcb.data.configure = NO_LOOPBACK | RECV_BROAD;
} else
adapter->tx_pcb.data.configure = NO_LOOPBACK | RECV_PROMISC;
/*
* configure adapter to receive messages (as specified above)
* and wait for response
*/
if (elp_debug >= 3)
pr_debug("%s: sending 82586 configure command\n", dev->name);
adapter->tx_pcb.command = CMD_CONFIGURE_82586;
adapter->tx_pcb.length = 2;
adapter->got[CMD_CONFIGURE_82586] = 0;
if (!send_pcb(dev, &adapter->tx_pcb))
{
spin_unlock_irqrestore(&adapter->lock, flags);
pr_err("%s: couldn't send 82586 configure command\n", dev->name);
}
else {
unsigned long timeout = jiffies + TIMEOUT;
spin_unlock_irqrestore(&adapter->lock, flags);
while (adapter->got[CMD_CONFIGURE_82586] == 0 && time_before(jiffies, timeout));
if (time_after_eq(jiffies, timeout))
TIMEOUT_MSG(__LINE__);
}
}
/************************************************************
*
* A couple of tests to see if there's 3C505 or not
* Called only by elp_autodetect
************************************************************/
static int __init elp_sense(struct net_device *dev)
{
int addr = dev->base_addr;
const char *name = dev->name;
byte orig_HSR;
if (!request_region(addr, ELP_IO_EXTENT, "3c505"))
return -ENODEV;
orig_HSR = inb_status(addr);
if (elp_debug > 0)
pr_debug(search_msg, name, addr);
if (orig_HSR == 0xff) {
if (elp_debug > 0)
pr_cont(notfound_msg, 1);
goto out;
}
/* Wait for a while; the adapter may still be booting up */
if (elp_debug > 0)
pr_cont(stilllooking_msg);
if (orig_HSR & DIR) {
/* If HCR.DIR is up, we pull it down. HSR.DIR should follow. */
outb(0, dev->base_addr + PORT_CONTROL);
msleep(300);
if (inb_status(addr) & DIR) {
if (elp_debug > 0)
pr_cont(notfound_msg, 2);
goto out;
}
} else {
/* If HCR.DIR is down, we pull it up. HSR.DIR should follow. */
outb(DIR, dev->base_addr + PORT_CONTROL);
msleep(300);
if (!(inb_status(addr) & DIR)) {
if (elp_debug > 0)
pr_cont(notfound_msg, 3);
goto out;
}
}
/*
* It certainly looks like a 3c505.
*/
if (elp_debug > 0)
pr_cont(found_msg);
return 0;
out:
release_region(addr, ELP_IO_EXTENT);
return -ENODEV;
}
/*************************************************************
*
* Search through addr_list[] and try to find a 3C505
* Called only by eplus_probe
*************************************************************/
static int __init elp_autodetect(struct net_device *dev)
{
int idx = 0;
/* if base address set, then only check that address
otherwise, run through the table */
if (dev->base_addr != 0) { /* dev->base_addr == 0 ==> plain autodetect */
if (elp_sense(dev) == 0)
return dev->base_addr;
} else
while ((dev->base_addr = addr_list[idx++])) {
if (elp_sense(dev) == 0)
return dev->base_addr;
}
/* could not find an adapter */
if (elp_debug > 0)
pr_debug(couldnot_msg, dev->name);
return 0; /* Because of this, the layer above will return -ENODEV */
}
static const struct net_device_ops elp_netdev_ops = {
.ndo_open = elp_open,
.ndo_stop = elp_close,
.ndo_get_stats = elp_get_stats,
.ndo_start_xmit = elp_start_xmit,
.ndo_tx_timeout = elp_timeout,
.ndo_set_rx_mode = elp_set_mc_list,
.ndo_change_mtu = eth_change_mtu,
.ndo_set_mac_address = eth_mac_addr,
.ndo_validate_addr = eth_validate_addr,
};
/******************************************************
*
* probe for an Etherlink Plus board at the specified address
*
******************************************************/
/* There are three situations we need to be able to detect here:
* a) the card is idle
* b) the card is still booting up
* c) the card is stuck in a strange state (some DOS drivers do this)
*
* In case (a), all is well. In case (b), we wait 10 seconds to see if the
* card finishes booting, and carry on if so. In case (c), we do a hard reset,
* loop round, and hope for the best.
*
* This is all very unpleasant, but hopefully avoids the problems with the old
* probe code (which had a 15-second delay if the card was idle, and didn't
* work at all if it was in a weird state).
*/
static int __init elplus_setup(struct net_device *dev)
{
elp_device *adapter = netdev_priv(dev);
int i, tries, tries1, okay;
unsigned long timeout;
unsigned long cookie = 0;
int err = -ENODEV;
/*
* setup adapter structure
*/
dev->base_addr = elp_autodetect(dev);
if (!dev->base_addr)
return -ENODEV;
adapter->send_pcb_semaphore = 0;
for (tries1 = 0; tries1 < 3; tries1++) {
outb_control((adapter->hcr_val | CMDE) & ~DIR, dev);
/* First try to write just one byte, to see if the card is
* responding at all normally.
*/
timeout = jiffies + 5*HZ/100;
okay = 0;
while (time_before(jiffies, timeout) && !(inb_status(dev->base_addr) & HCRE));
if ((inb_status(dev->base_addr) & HCRE)) {
outb_command(0, dev->base_addr); /* send a spurious byte */
timeout = jiffies + 5*HZ/100;
while (time_before(jiffies, timeout) && !(inb_status(dev->base_addr) & HCRE));
if (inb_status(dev->base_addr) & HCRE)
okay = 1;
}
if (!okay) {
/* Nope, it's ignoring the command register. This means that
* either it's still booting up, or it's died.
*/
pr_err("%s: command register wouldn't drain, ", dev->name);
if ((inb_status(dev->base_addr) & 7) == 3) {
/* If the adapter status is 3, it *could* still be booting.
* Give it the benefit of the doubt for 10 seconds.
*/
pr_cont("assuming 3c505 still starting\n");
timeout = jiffies + 10*HZ;
while (time_before(jiffies, timeout) && (inb_status(dev->base_addr) & 7));
if (inb_status(dev->base_addr) & 7) {
pr_err("%s: 3c505 failed to start\n", dev->name);
} else {
okay = 1; /* It started */
}
} else {
/* Otherwise, it must just be in a strange
* state. We probably need to kick it.
*/
pr_cont("3c505 is sulking\n");
}
}
for (tries = 0; tries < 5 && okay; tries++) {
/*
* Try to set the Ethernet address, to make sure that the board
* is working.
*/
adapter->tx_pcb.command = CMD_STATION_ADDRESS;
adapter->tx_pcb.length = 0;
cookie = probe_irq_on();
if (!send_pcb(dev, &adapter->tx_pcb)) {
pr_err("%s: could not send first PCB\n", dev->name);
probe_irq_off(cookie);
continue;
}
if (!receive_pcb(dev, &adapter->rx_pcb)) {
pr_err("%s: could not read first PCB\n", dev->name);
probe_irq_off(cookie);
continue;
}
if ((adapter->rx_pcb.command != CMD_ADDRESS_RESPONSE) ||
(adapter->rx_pcb.length != 6)) {
pr_err("%s: first PCB wrong (%d, %d)\n", dev->name,
adapter->rx_pcb.command, adapter->rx_pcb.length);
probe_irq_off(cookie);
continue;
}
goto okay;
}
/* It's broken. Do a hard reset to re-initialise the board,
* and try again.
*/
pr_info("%s: resetting adapter\n", dev->name);
outb_control(adapter->hcr_val | FLSH | ATTN, dev);
outb_control(adapter->hcr_val & ~(FLSH | ATTN), dev);
}
pr_err("%s: failed to initialise 3c505\n", dev->name);
goto out;
okay:
if (dev->irq) { /* Is there a preset IRQ? */
int rpt = probe_irq_off(cookie);
if (dev->irq != rpt) {
pr_warning("%s: warning, irq %d configured but %d detected\n", dev->name, dev->irq, rpt);
}
/* if dev->irq == probe_irq_off(cookie), all is well */
} else /* No preset IRQ; just use what we can detect */
dev->irq = probe_irq_off(cookie);
switch (dev->irq) { /* Legal, sane? */
case 0:
pr_err("%s: IRQ probe failed: check 3c505 jumpers.\n",
dev->name);
goto out;
case 1:
case 6:
case 8:
case 13:
pr_err("%s: Impossible IRQ %d reported by probe_irq_off().\n",
dev->name, dev->irq);
goto out;
}
/*
* Now we have the IRQ number so we can disable the interrupts from
* the board until the board is opened.
*/
outb_control(adapter->hcr_val & ~CMDE, dev);
/*
* copy Ethernet address into structure
*/
for (i = 0; i < 6; i++)
dev->dev_addr[i] = adapter->rx_pcb.data.eth_addr[i];
/* find a DMA channel */
if (!dev->dma) {
if (dev->mem_start) {
dev->dma = dev->mem_start & 7;
}
else {
pr_warning("%s: warning, DMA channel not specified, using default\n", dev->name);
dev->dma = ELP_DMA;
}
}
/*
* print remainder of startup message
*/
pr_info("%s: 3c505 at %#lx, irq %d, dma %d, addr %pM, ",
dev->name, dev->base_addr, dev->irq, dev->dma, dev->dev_addr);
/*
* read more information from the adapter
*/
adapter->tx_pcb.command = CMD_ADAPTER_INFO;
adapter->tx_pcb.length = 0;
if (!send_pcb(dev, &adapter->tx_pcb) ||
!receive_pcb(dev, &adapter->rx_pcb) ||
(adapter->rx_pcb.command != CMD_ADAPTER_INFO_RESPONSE) ||
(adapter->rx_pcb.length != 10)) {
pr_cont("not responding to second PCB\n");
}
pr_cont("rev %d.%d, %dk\n", adapter->rx_pcb.data.info.major_vers,
adapter->rx_pcb.data.info.minor_vers, adapter->rx_pcb.data.info.RAM_sz);
/*
* reconfigure the adapter memory to better suit our purposes
*/
adapter->tx_pcb.command = CMD_CONFIGURE_ADAPTER_MEMORY;
adapter->tx_pcb.length = 12;
adapter->tx_pcb.data.memconf.cmd_q = 8;
adapter->tx_pcb.data.memconf.rcv_q = 8;
adapter->tx_pcb.data.memconf.mcast = 10;
adapter->tx_pcb.data.memconf.frame = 10;
adapter->tx_pcb.data.memconf.rcv_b = 10;
adapter->tx_pcb.data.memconf.progs = 0;
if (!send_pcb(dev, &adapter->tx_pcb) ||
!receive_pcb(dev, &adapter->rx_pcb) ||
(adapter->rx_pcb.command != CMD_CONFIGURE_ADAPTER_RESPONSE) ||
(adapter->rx_pcb.length != 2)) {
pr_err("%s: could not configure adapter memory\n", dev->name);
}
if (adapter->rx_pcb.data.configure) {
pr_err("%s: adapter configuration failed\n", dev->name);
}
dev->netdev_ops = &elp_netdev_ops;
dev->watchdog_timeo = 10*HZ;
dev->ethtool_ops = &netdev_ethtool_ops; /* local */
dev->mem_start = dev->mem_end = 0;
err = register_netdev(dev);
if (err)
goto out;
return 0;
out:
release_region(dev->base_addr, ELP_IO_EXTENT);
return err;
}
#ifndef MODULE
struct net_device * __init elplus_probe(int unit)
{
struct net_device *dev = alloc_etherdev(sizeof(elp_device));
int err;
if (!dev)
return ERR_PTR(-ENOMEM);
sprintf(dev->name, "eth%d", unit);
netdev_boot_setup_check(dev);
err = elplus_setup(dev);
if (err) {
free_netdev(dev);
return ERR_PTR(err);
}
return dev;
}
#else
static struct net_device *dev_3c505[ELP_MAX_CARDS];
static int io[ELP_MAX_CARDS];
static int irq[ELP_MAX_CARDS];
static int dma[ELP_MAX_CARDS];
module_param_array(io, int, NULL, 0);
module_param_array(irq, int, NULL, 0);
module_param_array(dma, int, NULL, 0);
MODULE_PARM_DESC(io, "EtherLink Plus I/O base address(es)");
MODULE_PARM_DESC(irq, "EtherLink Plus IRQ number(s) (assigned)");
MODULE_PARM_DESC(dma, "EtherLink Plus DMA channel(s)");
int __init init_module(void)
{
int this_dev, found = 0;
for (this_dev = 0; this_dev < ELP_MAX_CARDS; this_dev++) {
struct net_device *dev = alloc_etherdev(sizeof(elp_device));
if (!dev)
break;
dev->irq = irq[this_dev];
dev->base_addr = io[this_dev];
if (dma[this_dev]) {
dev->dma = dma[this_dev];
} else {
dev->dma = ELP_DMA;
pr_warning("3c505.c: warning, using default DMA channel,\n");
}
if (io[this_dev] == 0) {
if (this_dev) {
free_netdev(dev);
break;
}
pr_notice("3c505.c: module autoprobe not recommended, give io=xx.\n");
}
if (elplus_setup(dev) != 0) {
pr_warning("3c505.c: Failed to register card at 0x%x.\n", io[this_dev]);
free_netdev(dev);
break;
}
dev_3c505[this_dev] = dev;
found++;
}
if (!found)
return -ENODEV;
return 0;
}
void __exit cleanup_module(void)
{
int this_dev;
for (this_dev = 0; this_dev < ELP_MAX_CARDS; this_dev++) {
struct net_device *dev = dev_3c505[this_dev];
if (dev) {
unregister_netdev(dev);
release_region(dev->base_addr, ELP_IO_EXTENT);
free_netdev(dev);
}
}
}
#endif /* MODULE */
MODULE_LICENSE("GPL");
/*****************************************************************
*
* defines for 3Com Etherlink Plus adapter
*
*****************************************************************/
#define ELP_DMA 6
#define ELP_RX_PCBS 4
#define ELP_MAX_CARDS 4
/*
* I/O register offsets
*/
#define PORT_COMMAND 0x00 /* read/write, 8-bit */
#define PORT_STATUS 0x02 /* read only, 8-bit */
#define PORT_AUXDMA 0x02 /* write only, 8-bit */
#define PORT_DATA 0x04 /* read/write, 16-bit */
#define PORT_CONTROL 0x06 /* read/write, 8-bit */
#define ELP_IO_EXTENT 0x10 /* size of used IO registers */
/*
* host control registers bits
*/
#define ATTN 0x80 /* attention */
#define FLSH 0x40 /* flush data register */
#define DMAE 0x20 /* DMA enable */
#define DIR 0x10 /* direction */
#define TCEN 0x08 /* terminal count interrupt enable */
#define CMDE 0x04 /* command register interrupt enable */
#define HSF2 0x02 /* host status flag 2 */
#define HSF1 0x01 /* host status flag 1 */
/*
* combinations of HSF flags used for PCB transmission
*/
#define HSF_PCB_ACK HSF1
#define HSF_PCB_NAK HSF2
#define HSF_PCB_END (HSF2|HSF1)
#define HSF_PCB_MASK (HSF2|HSF1)
/*
* host status register bits
*/
#define HRDY 0x80 /* data register ready */
#define HCRE 0x40 /* command register empty */
#define ACRF 0x20 /* adapter command register full */
/* #define DIR 0x10 direction - same as in control register */
#define DONE 0x08 /* DMA done */
#define ASF3 0x04 /* adapter status flag 3 */
#define ASF2 0x02 /* adapter status flag 2 */
#define ASF1 0x01 /* adapter status flag 1 */
/*
* combinations of ASF flags used for PCB reception
*/
#define ASF_PCB_ACK ASF1
#define ASF_PCB_NAK ASF2
#define ASF_PCB_END (ASF2|ASF1)
#define ASF_PCB_MASK (ASF2|ASF1)
/*
* host aux DMA register bits
*/
#define DMA_BRST 0x01 /* DMA burst */
/*
* maximum amount of data allowed in a PCB
*/
#define MAX_PCB_DATA 62
/*****************************************************************
*
* timeout value
* this is a rough value used for loops to stop them from
* locking up the whole machine in the case of failure or
* error conditions
*
*****************************************************************/
#define TIMEOUT 300
/*****************************************************************
*
* PCB commands
*
*****************************************************************/
enum {
/*
* host PCB commands
*/
CMD_CONFIGURE_ADAPTER_MEMORY = 0x01,
CMD_CONFIGURE_82586 = 0x02,
CMD_STATION_ADDRESS = 0x03,
CMD_DMA_DOWNLOAD = 0x04,
CMD_DMA_UPLOAD = 0x05,
CMD_PIO_DOWNLOAD = 0x06,
CMD_PIO_UPLOAD = 0x07,
CMD_RECEIVE_PACKET = 0x08,
CMD_TRANSMIT_PACKET = 0x09,
CMD_NETWORK_STATISTICS = 0x0a,
CMD_LOAD_MULTICAST_LIST = 0x0b,
CMD_CLEAR_PROGRAM = 0x0c,
CMD_DOWNLOAD_PROGRAM = 0x0d,
CMD_EXECUTE_PROGRAM = 0x0e,
CMD_SELF_TEST = 0x0f,
CMD_SET_STATION_ADDRESS = 0x10,
CMD_ADAPTER_INFO = 0x11,
NUM_TRANSMIT_CMDS,
/*
* adapter PCB commands
*/
CMD_CONFIGURE_ADAPTER_RESPONSE = 0x31,
CMD_CONFIGURE_82586_RESPONSE = 0x32,
CMD_ADDRESS_RESPONSE = 0x33,
CMD_DOWNLOAD_DATA_REQUEST = 0x34,
CMD_UPLOAD_DATA_REQUEST = 0x35,
CMD_RECEIVE_PACKET_COMPLETE = 0x38,
CMD_TRANSMIT_PACKET_COMPLETE = 0x39,
CMD_NETWORK_STATISTICS_RESPONSE = 0x3a,
CMD_LOAD_MULTICAST_RESPONSE = 0x3b,
CMD_CLEAR_PROGRAM_RESPONSE = 0x3c,
CMD_DOWNLOAD_PROGRAM_RESPONSE = 0x3d,
CMD_EXECUTE_RESPONSE = 0x3e,
CMD_SELF_TEST_RESPONSE = 0x3f,
CMD_SET_ADDRESS_RESPONSE = 0x40,
CMD_ADAPTER_INFO_RESPONSE = 0x41
};
/* Definitions for the PCB data structure */
/* Data units */
typedef unsigned char byte;
typedef unsigned short int word;
typedef unsigned long int dword;
/* Data structures */
struct Memconf {
word cmd_q,
rcv_q,
mcast,
frame,
rcv_b,
progs;
};
struct Rcv_pkt {
word buf_ofs,
buf_seg,
buf_len,
timeout;
};
struct Xmit_pkt {
word buf_ofs,
buf_seg,
pkt_len;
};
struct Rcv_resp {
word buf_ofs,
buf_seg,
buf_len,
pkt_len,
timeout,
status;
dword timetag;
};
struct Xmit_resp {
word buf_ofs,
buf_seg,
c_stat,
status;
};
struct Netstat {
dword tot_recv,
tot_xmit;
word err_CRC,
err_align,
err_res,
err_ovrrun;
};
struct Selftest {
word error;
union {
word ROM_cksum;
struct {
word ofs, seg;
} RAM;
word i82586;
} failure;
};
struct Info {
byte minor_vers,
major_vers;
word ROM_cksum,
RAM_sz,
free_ofs,
free_seg;
};
struct Memdump {
word size,
off,
seg;
};
/*
Primary Command Block. The most important data structure. All communication
between the host and the adapter is done with these. (Except for the actual
Ethernet data, which has different packaging.)
*/
typedef struct {
byte command;
byte length;
union {
struct Memconf memconf;
word configure;
struct Rcv_pkt rcv_pkt;
struct Xmit_pkt xmit_pkt;
byte multicast[10][6];
byte eth_addr[6];
byte failed;
struct Rcv_resp rcv_resp;
struct Xmit_resp xmit_resp;
struct Netstat netstat;
struct Selftest selftest;
struct Info info;
struct Memdump memdump;
byte raw[62];
} data;
} pcb_struct;
/* These defines for 'configure' */
#define RECV_STATION 0x00
#define RECV_BROAD 0x01
#define RECV_MULTI 0x02
#define RECV_PROMISC 0x04
#define NO_LOOPBACK 0x00
#define INT_LOOPBACK 0x08
#define EXT_LOOPBACK 0x10
/*****************************************************************
*
* structure to hold context information for adapter
*
*****************************************************************/
#define DMA_BUFFER_SIZE 1600
#define BACKLOG_SIZE 4
typedef struct {
volatile short got[NUM_TRANSMIT_CMDS]; /* flags for
command completion */
pcb_struct tx_pcb; /* PCB for foreground sending */
pcb_struct rx_pcb; /* PCB for foreground receiving */
pcb_struct itx_pcb; /* PCB for background sending */
pcb_struct irx_pcb; /* PCB for background receiving */
void *dma_buffer;
struct {
unsigned int length[BACKLOG_SIZE];
unsigned int in;
unsigned int out;
} rx_backlog;
struct {
unsigned int direction;
unsigned int length;
struct sk_buff *skb;
void *target;
unsigned long start_time;
} current_dma;
/* flags */
unsigned long send_pcb_semaphore;
unsigned long dmaing;
unsigned long busy;
unsigned int rx_active; /* number of receive PCBs */
volatile unsigned char hcr_val; /* what we think the HCR contains */
spinlock_t lock; /* Interrupt v tx lock */
} elp_device;
/* 3c507.c: An EtherLink16 device driver for Linux. */
/*
Written 1993,1994 by Donald Becker.
Copyright 1993 United States Government as represented by the
Director, National Security Agency.
This software may be used and distributed according to the terms
of the GNU General Public License, incorporated herein by reference.
The author may be reached as becker@scyld.com, or C/O
Scyld Computing Corporation
410 Severn Ave., Suite 210
Annapolis MD 21403
Thanks go to jennings@Montrouge.SMR.slb.com ( Patrick Jennings)
and jrs@world.std.com (Rick Sladkey) for testing and bugfixes.
Mark Salazar <leslie@access.digex.net> made the changes for cards with
only 16K packet buffers.
Things remaining to do:
Verify that the tx and rx buffers don't have fencepost errors.
Move the theory of operation and memory map documentation.
The statistics need to be updated correctly.
*/
#define DRV_NAME "3c507"
#define DRV_VERSION "1.10a"
#define DRV_RELDATE "11/17/2001"
static const char version[] =
DRV_NAME ".c:v" DRV_VERSION " " DRV_RELDATE " Donald Becker (becker@scyld.com)\n";
/*
Sources:
This driver wouldn't have been written with the availability of the
Crynwr driver source code. It provided a known-working implementation
that filled in the gaping holes of the Intel documentation. Three cheers
for Russ Nelson.
Intel Microcommunications Databook, Vol. 1, 1990. It provides just enough
info that the casual reader might think that it documents the i82586 :-<.
*/
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/fcntl.h>
#include <linux/interrupt.h>
#include <linux/ioport.h>
#include <linux/in.h>
#include <linux/string.h>
#include <linux/spinlock.h>
#include <linux/ethtool.h>
#include <linux/errno.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/if_ether.h>
#include <linux/skbuff.h>
#include <linux/init.h>
#include <linux/bitops.h>
#include <asm/dma.h>
#include <asm/io.h>
#include <asm/uaccess.h>
/* use 0 for production, 1 for verification, 2..7 for debug */
#ifndef NET_DEBUG
#define NET_DEBUG 1
#endif
static unsigned int net_debug = NET_DEBUG;
#define debug net_debug
/*
Details of the i82586.
You'll really need the databook to understand the details of this part,
but the outline is that the i82586 has two separate processing units.
Both are started from a list of three configuration tables, of which only
the last, the System Control Block (SCB), is used after reset-time. The SCB
has the following fields:
Status word
Command word
Tx/Command block addr.
Rx block addr.
The command word accepts the following controls for the Tx and Rx units:
*/
#define CUC_START 0x0100
#define CUC_RESUME 0x0200
#define CUC_SUSPEND 0x0300
#define RX_START 0x0010
#define RX_RESUME 0x0020
#define RX_SUSPEND 0x0030
/* The Rx unit uses a list of frame descriptors and a list of data buffer
descriptors. We use full-sized (1518 byte) data buffers, so there is
a one-to-one pairing of frame descriptors to buffer descriptors.
The Tx ("command") unit executes a list of commands that look like:
Status word Written by the 82586 when the command is done.
Command word Command in lower 3 bits, post-command action in upper 3
Link word The address of the next command.
Parameters (as needed).
Some definitions related to the Command Word are:
*/
#define CMD_EOL 0x8000 /* The last command of the list, stop. */
#define CMD_SUSP 0x4000 /* Suspend after doing cmd. */
#define CMD_INTR 0x2000 /* Interrupt after doing cmd. */
enum commands {
CmdNOp = 0, CmdSASetup = 1, CmdConfigure = 2, CmdMulticastList = 3,
CmdTx = 4, CmdTDR = 5, CmdDump = 6, CmdDiagnose = 7};
/* Information that need to be kept for each board. */
struct net_local {
int last_restart;
ushort rx_head;
ushort rx_tail;
ushort tx_head;
ushort tx_cmd_link;
ushort tx_reap;
ushort tx_pkts_in_ring;
spinlock_t lock;
void __iomem *base;
};
/*
Details of the EtherLink16 Implementation
The 3c507 is a generic shared-memory i82586 implementation.
The host can map 16K, 32K, 48K, or 64K of the 64K memory into
0x0[CD][08]0000, or all 64K into 0xF[02468]0000.
*/
/* Offsets from the base I/O address. */
#define SA_DATA 0 /* Station address data, or 3Com signature. */
#define MISC_CTRL 6 /* Switch the SA_DATA banks, and bus config bits. */
#define RESET_IRQ 10 /* Reset the latched IRQ line. */
#define SIGNAL_CA 11 /* Frob the 82586 Channel Attention line. */
#define ROM_CONFIG 13
#define MEM_CONFIG 14
#define IRQ_CONFIG 15
#define EL16_IO_EXTENT 16
/* The ID port is used at boot-time to locate the ethercard. */
#define ID_PORT 0x100
/* Offsets to registers in the mailbox (SCB). */
#define iSCB_STATUS 0x8
#define iSCB_CMD 0xA
#define iSCB_CBL 0xC /* Command BLock offset. */
#define iSCB_RFA 0xE /* Rx Frame Area offset. */
/* Since the 3c507 maps the shared memory window so that the last byte is
at 82586 address FFFF, the first byte is at 82586 address 0, 16K, 32K, or
48K corresponding to window sizes of 64K, 48K, 32K and 16K respectively.
We can account for this be setting the 'SBC Base' entry in the ISCP table
below for all the 16 bit offset addresses, and also adding the 'SCB Base'
value to all 24 bit physical addresses (in the SCP table and the TX and RX
Buffer Descriptors).
-Mark
*/
#define SCB_BASE ((unsigned)64*1024 - (dev->mem_end - dev->mem_start))
/*
What follows in 'init_words[]' is the "program" that is downloaded to the
82586 memory. It's mostly tables and command blocks, and starts at the
reset address 0xfffff6. This is designed to be similar to the EtherExpress,
thus the unusual location of the SCB at 0x0008.
Even with the additional "don't care" values, doing it this way takes less
program space than initializing the individual tables, and I feel it's much
cleaner.
The databook is particularly useless for the first two structures, I had
to use the Crynwr driver as an example.
The memory setup is as follows:
*/
#define CONFIG_CMD 0x0018
#define SET_SA_CMD 0x0024
#define SA_OFFSET 0x002A
#define IDLELOOP 0x30
#define TDR_CMD 0x38
#define TDR_TIME 0x3C
#define DUMP_CMD 0x40
#define DIAG_CMD 0x48
#define SET_MC_CMD 0x4E
#define DUMP_DATA 0x56 /* A 170 byte buffer for dump and Set-MC into. */
#define TX_BUF_START 0x0100
#define NUM_TX_BUFS 5
#define TX_BUF_SIZE (1518+14+20+16) /* packet+header+TBD */
#define RX_BUF_START 0x2000
#define RX_BUF_SIZE (1518+14+18) /* packet+header+RBD */
#define RX_BUF_END (dev->mem_end - dev->mem_start)
#define TX_TIMEOUT (HZ/20)
/*
That's it: only 86 bytes to set up the beast, including every extra
command available. The 170 byte buffer at DUMP_DATA is shared between the
Dump command (called only by the diagnostic program) and the SetMulticastList
command.
To complete the memory setup you only have to write the station address at
SA_OFFSET and create the Tx & Rx buffer lists.
The Tx command chain and buffer list is setup as follows:
A Tx command table, with the data buffer pointing to...
A Tx data buffer descriptor. The packet is in a single buffer, rather than
chaining together several smaller buffers.
A NoOp command, which initially points to itself,
And the packet data.
A transmit is done by filling in the Tx command table and data buffer,
re-writing the NoOp command, and finally changing the offset of the last
command to point to the current Tx command. When the Tx command is finished,
it jumps to the NoOp, when it loops until the next Tx command changes the
"link offset" in the NoOp. This way the 82586 never has to go through the
slow restart sequence.
The Rx buffer list is set up in the obvious ring structure. We have enough
memory (and low enough interrupt latency) that we can avoid the complicated
Rx buffer linked lists by alway associating a full-size Rx data buffer with
each Rx data frame.
I current use four transmit buffers starting at TX_BUF_START (0x0100), and
use the rest of memory, from RX_BUF_START to RX_BUF_END, for Rx buffers.
*/
static unsigned short init_words[] = {
/* System Configuration Pointer (SCP). */
0x0000, /* Set bus size to 16 bits. */
0,0, /* pad words. */
0x0000,0x0000, /* ISCP phys addr, set in init_82586_mem(). */
/* Intermediate System Configuration Pointer (ISCP). */
0x0001, /* Status word that's cleared when init is done. */
0x0008,0,0, /* SCB offset, (skip, skip) */
/* System Control Block (SCB). */
0,0xf000|RX_START|CUC_START, /* SCB status and cmd. */
CONFIG_CMD, /* Command list pointer, points to Configure. */
RX_BUF_START, /* Rx block list. */
0,0,0,0, /* Error count: CRC, align, buffer, overrun. */
/* 0x0018: Configure command. Change to put MAC data with packet. */
0, CmdConfigure, /* Status, command. */
SET_SA_CMD, /* Next command is Set Station Addr. */
0x0804, /* "4" bytes of config data, 8 byte FIFO. */
0x2e40, /* Magic values, including MAC data location. */
0, /* Unused pad word. */
/* 0x0024: Setup station address command. */
0, CmdSASetup,
SET_MC_CMD, /* Next command. */
0xaa00,0xb000,0x0bad, /* Station address (to be filled in) */
/* 0x0030: NOP, looping back to itself. Point to first Tx buffer to Tx. */
0, CmdNOp, IDLELOOP, 0 /* pad */,
/* 0x0038: A unused Time-Domain Reflectometer command. */
0, CmdTDR, IDLELOOP, 0,
/* 0x0040: An unused Dump State command. */
0, CmdDump, IDLELOOP, DUMP_DATA,
/* 0x0048: An unused Diagnose command. */
0, CmdDiagnose, IDLELOOP,
/* 0x004E: An empty set-multicast-list command. */
0, CmdMulticastList, IDLELOOP, 0,
};
/* Index to functions, as function prototypes. */
static int el16_probe1(struct net_device *dev, int ioaddr);
static int el16_open(struct net_device *dev);
static netdev_tx_t el16_send_packet(struct sk_buff *skb,
struct net_device *dev);
static irqreturn_t el16_interrupt(int irq, void *dev_id);
static void el16_rx(struct net_device *dev);
static int el16_close(struct net_device *dev);
static void el16_tx_timeout (struct net_device *dev);
static void hardware_send_packet(struct net_device *dev, void *buf, short length, short pad);
static void init_82586_mem(struct net_device *dev);
static const struct ethtool_ops netdev_ethtool_ops;
static void init_rx_bufs(struct net_device *);
static int io = 0x300;
static int irq;
static int mem_start;
/* Check for a network adaptor of this type, and return '0' iff one exists.
If dev->base_addr == 0, probe all likely locations.
If dev->base_addr == 1, always return failure.
If dev->base_addr == 2, (detachable devices only) allocate space for the
device and return success.
*/
struct net_device * __init el16_probe(int unit)
{
struct net_device *dev = alloc_etherdev(sizeof(struct net_local));
static const unsigned ports[] = { 0x300, 0x320, 0x340, 0x280, 0};
const unsigned *port;
int err = -ENODEV;
if (!dev)
return ERR_PTR(-ENODEV);
if (unit >= 0) {
sprintf(dev->name, "eth%d", unit);
netdev_boot_setup_check(dev);
io = dev->base_addr;
irq = dev->irq;
mem_start = dev->mem_start & 15;
}
if (io > 0x1ff) /* Check a single specified location. */
err = el16_probe1(dev, io);
else if (io != 0)
err = -ENXIO; /* Don't probe at all. */
else {
for (port = ports; *port; port++) {
err = el16_probe1(dev, *port);
if (!err)
break;
}
}
if (err)
goto out;
err = register_netdev(dev);
if (err)
goto out1;
return dev;
out1:
free_irq(dev->irq, dev);
iounmap(((struct net_local *)netdev_priv(dev))->base);
release_region(dev->base_addr, EL16_IO_EXTENT);
out:
free_netdev(dev);
return ERR_PTR(err);
}
static const struct net_device_ops netdev_ops = {
.ndo_open = el16_open,
.ndo_stop = el16_close,
.ndo_start_xmit = el16_send_packet,
.ndo_tx_timeout = el16_tx_timeout,
.ndo_change_mtu = eth_change_mtu,
.ndo_set_mac_address = eth_mac_addr,
.ndo_validate_addr = eth_validate_addr,
};
static int __init el16_probe1(struct net_device *dev, int ioaddr)
{
static unsigned char init_ID_done;
int i, irq, irqval, retval;
struct net_local *lp;
if (init_ID_done == 0) {
ushort lrs_state = 0xff;
/* Send the ID sequence to the ID_PORT to enable the board(s). */
outb(0x00, ID_PORT);
for(i = 0; i < 255; i++) {
outb(lrs_state, ID_PORT);
lrs_state <<= 1;
if (lrs_state & 0x100)
lrs_state ^= 0xe7;
}
outb(0x00, ID_PORT);
init_ID_done = 1;
}
if (!request_region(ioaddr, EL16_IO_EXTENT, DRV_NAME))
return -ENODEV;
if ((inb(ioaddr) != '*') || (inb(ioaddr + 1) != '3') ||
(inb(ioaddr + 2) != 'C') || (inb(ioaddr + 3) != 'O')) {
retval = -ENODEV;
goto out;
}
pr_info("%s: 3c507 at %#x,", dev->name, ioaddr);
/* We should make a few more checks here, like the first three octets of
the S.A. for the manufacturer's code. */
irq = inb(ioaddr + IRQ_CONFIG) & 0x0f;
irqval = request_irq(irq, el16_interrupt, 0, DRV_NAME, dev);
if (irqval) {
pr_cont("\n");
pr_err("3c507: unable to get IRQ %d (irqval=%d).\n", irq, irqval);
retval = -EAGAIN;
goto out;
}
/* We've committed to using the board, and can start filling in *dev. */
dev->base_addr = ioaddr;
outb(0x01, ioaddr + MISC_CTRL);
for (i = 0; i < 6; i++)
dev->dev_addr[i] = inb(ioaddr + i);
pr_cont(" %pM", dev->dev_addr);
if (mem_start)
net_debug = mem_start & 7;
#ifdef MEM_BASE
dev->mem_start = MEM_BASE;
dev->mem_end = dev->mem_start + 0x10000;
#else
{
int base;
int size;
char mem_config = inb(ioaddr + MEM_CONFIG);
if (mem_config & 0x20) {
size = 64*1024;
base = 0xf00000 + (mem_config & 0x08 ? 0x080000
: ((mem_config & 3) << 17));
} else {
size = ((mem_config & 3) + 1) << 14;
base = 0x0c0000 + ( (mem_config & 0x18) << 12);
}
dev->mem_start = base;
dev->mem_end = base + size;
}
#endif
dev->if_port = (inb(ioaddr + ROM_CONFIG) & 0x80) ? 1 : 0;
dev->irq = inb(ioaddr + IRQ_CONFIG) & 0x0f;
pr_cont(", IRQ %d, %sternal xcvr, memory %#lx-%#lx.\n", dev->irq,
dev->if_port ? "ex" : "in", dev->mem_start, dev->mem_end-1);
if (net_debug)
pr_debug("%s", version);
lp = netdev_priv(dev);
spin_lock_init(&lp->lock);
lp->base = ioremap(dev->mem_start, RX_BUF_END);
if (!lp->base) {
pr_err("3c507: unable to remap memory\n");
retval = -EAGAIN;
goto out1;
}
dev->netdev_ops = &netdev_ops;
dev->watchdog_timeo = TX_TIMEOUT;
dev->ethtool_ops = &netdev_ethtool_ops;
dev->flags &= ~IFF_MULTICAST; /* Multicast doesn't work */
return 0;
out1:
free_irq(dev->irq, dev);
out:
release_region(ioaddr, EL16_IO_EXTENT);
return retval;
}
static int el16_open(struct net_device *dev)
{
/* Initialize the 82586 memory and start it. */
init_82586_mem(dev);
netif_start_queue(dev);
return 0;
}
static void el16_tx_timeout (struct net_device *dev)
{
struct net_local *lp = netdev_priv(dev);
int ioaddr = dev->base_addr;
void __iomem *shmem = lp->base;
if (net_debug > 1)
pr_debug("%s: transmit timed out, %s? ", dev->name,
readw(shmem + iSCB_STATUS) & 0x8000 ? "IRQ conflict" :
"network cable problem");
/* Try to restart the adaptor. */
if (lp->last_restart == dev->stats.tx_packets) {
if (net_debug > 1)
pr_cont("Resetting board.\n");
/* Completely reset the adaptor. */
init_82586_mem (dev);
lp->tx_pkts_in_ring = 0;
} else {
/* Issue the channel attention signal and hope it "gets better". */
if (net_debug > 1)
pr_cont("Kicking board.\n");
writew(0xf000 | CUC_START | RX_START, shmem + iSCB_CMD);
outb (0, ioaddr + SIGNAL_CA); /* Issue channel-attn. */
lp->last_restart = dev->stats.tx_packets;
}
dev->trans_start = jiffies; /* prevent tx timeout */
netif_wake_queue (dev);
}
static netdev_tx_t el16_send_packet (struct sk_buff *skb,
struct net_device *dev)
{
struct net_local *lp = netdev_priv(dev);
int ioaddr = dev->base_addr;
unsigned long flags;
short length = ETH_ZLEN < skb->len ? skb->len : ETH_ZLEN;
unsigned char *buf = skb->data;
netif_stop_queue (dev);
spin_lock_irqsave (&lp->lock, flags);
dev->stats.tx_bytes += length;
/* Disable the 82586's input to the interrupt line. */
outb (0x80, ioaddr + MISC_CTRL);
hardware_send_packet (dev, buf, skb->len, length - skb->len);
/* Enable the 82586 interrupt input. */
outb (0x84, ioaddr + MISC_CTRL);
spin_unlock_irqrestore (&lp->lock, flags);
dev_kfree_skb (skb);
/* You might need to clean up and record Tx statistics here. */
return NETDEV_TX_OK;
}
/* The typical workload of the driver:
Handle the network interface interrupts. */
static irqreturn_t el16_interrupt(int irq, void *dev_id)
{
struct net_device *dev = dev_id;
struct net_local *lp;
int ioaddr, status, boguscount = 0;
ushort ack_cmd = 0;
void __iomem *shmem;
if (dev == NULL) {
pr_err("net_interrupt(): irq %d for unknown device.\n", irq);
return IRQ_NONE;
}
ioaddr = dev->base_addr;
lp = netdev_priv(dev);
shmem = lp->base;
spin_lock(&lp->lock);
status = readw(shmem+iSCB_STATUS);
if (net_debug > 4) {
pr_debug("%s: 3c507 interrupt, status %4.4x.\n", dev->name, status);
}
/* Disable the 82586's input to the interrupt line. */
outb(0x80, ioaddr + MISC_CTRL);
/* Reap the Tx packet buffers. */
while (lp->tx_pkts_in_ring) {
unsigned short tx_status = readw(shmem+lp->tx_reap);
if (!(tx_status & 0x8000)) {
if (net_debug > 5)
pr_debug("Tx command incomplete (%#x).\n", lp->tx_reap);
break;
}
/* Tx unsuccessful or some interesting status bit set. */
if (!(tx_status & 0x2000) || (tx_status & 0x0f3f)) {
dev->stats.tx_errors++;
if (tx_status & 0x0600) dev->stats.tx_carrier_errors++;
if (tx_status & 0x0100) dev->stats.tx_fifo_errors++;
if (!(tx_status & 0x0040)) dev->stats.tx_heartbeat_errors++;
if (tx_status & 0x0020) dev->stats.tx_aborted_errors++;
dev->stats.collisions += tx_status & 0xf;
}
dev->stats.tx_packets++;
if (net_debug > 5)
pr_debug("Reaped %x, Tx status %04x.\n" , lp->tx_reap, tx_status);
lp->tx_reap += TX_BUF_SIZE;
if (lp->tx_reap > RX_BUF_START - TX_BUF_SIZE)
lp->tx_reap = TX_BUF_START;
lp->tx_pkts_in_ring--;
/* There is always more space in the Tx ring buffer now. */
netif_wake_queue(dev);
if (++boguscount > 10)
break;
}
if (status & 0x4000) { /* Packet received. */
if (net_debug > 5)
pr_debug("Received packet, rx_head %04x.\n", lp->rx_head);
el16_rx(dev);
}
/* Acknowledge the interrupt sources. */
ack_cmd = status & 0xf000;
if ((status & 0x0700) != 0x0200 && netif_running(dev)) {
if (net_debug)
pr_debug("%s: Command unit stopped, status %04x, restarting.\n",
dev->name, status);
/* If this ever occurs we should really re-write the idle loop, reset
the Tx list, and do a complete restart of the command unit.
For now we rely on the Tx timeout if the resume doesn't work. */
ack_cmd |= CUC_RESUME;
}
if ((status & 0x0070) != 0x0040 && netif_running(dev)) {
/* The Rx unit is not ready, it must be hung. Restart the receiver by
initializing the rx buffers, and issuing an Rx start command. */
if (net_debug)
pr_debug("%s: Rx unit stopped, status %04x, restarting.\n",
dev->name, status);
init_rx_bufs(dev);
writew(RX_BUF_START,shmem+iSCB_RFA);
ack_cmd |= RX_START;
}
writew(ack_cmd,shmem+iSCB_CMD);
outb(0, ioaddr + SIGNAL_CA); /* Issue channel-attn. */
/* Clear the latched interrupt. */
outb(0, ioaddr + RESET_IRQ);
/* Enable the 82586's interrupt input. */
outb(0x84, ioaddr + MISC_CTRL);
spin_unlock(&lp->lock);
return IRQ_HANDLED;
}
static int el16_close(struct net_device *dev)
{
struct net_local *lp = netdev_priv(dev);
int ioaddr = dev->base_addr;
void __iomem *shmem = lp->base;
netif_stop_queue(dev);
/* Flush the Tx and disable Rx. */
writew(RX_SUSPEND | CUC_SUSPEND,shmem+iSCB_CMD);
outb(0, ioaddr + SIGNAL_CA);
/* Disable the 82586's input to the interrupt line. */
outb(0x80, ioaddr + MISC_CTRL);
/* We always physically use the IRQ line, so we don't do free_irq(). */
/* Update the statistics here. */
return 0;
}
/* Initialize the Rx-block list. */
static void init_rx_bufs(struct net_device *dev)
{
struct net_local *lp = netdev_priv(dev);
void __iomem *write_ptr;
unsigned short SCB_base = SCB_BASE;
int cur_rxbuf = lp->rx_head = RX_BUF_START;
/* Initialize each Rx frame + data buffer. */
do { /* While there is room for one more. */
write_ptr = lp->base + cur_rxbuf;
writew(0x0000,write_ptr); /* Status */
writew(0x0000,write_ptr+=2); /* Command */
writew(cur_rxbuf + RX_BUF_SIZE,write_ptr+=2); /* Link */
writew(cur_rxbuf + 22,write_ptr+=2); /* Buffer offset */
writew(0x0000,write_ptr+=2); /* Pad for dest addr. */
writew(0x0000,write_ptr+=2);
writew(0x0000,write_ptr+=2);
writew(0x0000,write_ptr+=2); /* Pad for source addr. */
writew(0x0000,write_ptr+=2);
writew(0x0000,write_ptr+=2);
writew(0x0000,write_ptr+=2); /* Pad for protocol. */
writew(0x0000,write_ptr+=2); /* Buffer: Actual count */
writew(-1,write_ptr+=2); /* Buffer: Next (none). */
writew(cur_rxbuf + 0x20 + SCB_base,write_ptr+=2);/* Buffer: Address low */
writew(0x0000,write_ptr+=2);
/* Finally, the number of bytes in the buffer. */
writew(0x8000 + RX_BUF_SIZE-0x20,write_ptr+=2);
lp->rx_tail = cur_rxbuf;
cur_rxbuf += RX_BUF_SIZE;
} while (cur_rxbuf <= RX_BUF_END - RX_BUF_SIZE);
/* Terminate the list by setting the EOL bit, and wrap the pointer to make
the list a ring. */
write_ptr = lp->base + lp->rx_tail + 2;
writew(0xC000,write_ptr); /* Command, mark as last. */
writew(lp->rx_head,write_ptr+2); /* Link */
}
static void init_82586_mem(struct net_device *dev)
{
struct net_local *lp = netdev_priv(dev);
short ioaddr = dev->base_addr;
void __iomem *shmem = lp->base;
/* Enable loopback to protect the wire while starting up,
and hold the 586 in reset during the memory initialization. */
outb(0x20, ioaddr + MISC_CTRL);
/* Fix the ISCP address and base. */
init_words[3] = SCB_BASE;
init_words[7] = SCB_BASE;
/* Write the words at 0xfff6 (address-aliased to 0xfffff6). */
memcpy_toio(lp->base + RX_BUF_END - 10, init_words, 10);
/* Write the words at 0x0000. */
memcpy_toio(lp->base, init_words + 5, sizeof(init_words) - 10);
/* Fill in the station address. */
memcpy_toio(lp->base+SA_OFFSET, dev->dev_addr, ETH_ALEN);
/* The Tx-block list is written as needed. We just set up the values. */
lp->tx_cmd_link = IDLELOOP + 4;
lp->tx_head = lp->tx_reap = TX_BUF_START;
init_rx_bufs(dev);
/* Start the 586 by releasing the reset line, but leave loopback. */
outb(0xA0, ioaddr + MISC_CTRL);
/* This was time consuming to track down: you need to give two channel
attention signals to reliably start up the i82586. */
outb(0, ioaddr + SIGNAL_CA);
{
int boguscnt = 50;
while (readw(shmem+iSCB_STATUS) == 0)
if (--boguscnt == 0) {
pr_warning("%s: i82586 initialization timed out with status %04x, cmd %04x.\n",
dev->name, readw(shmem+iSCB_STATUS), readw(shmem+iSCB_CMD));
break;
}
/* Issue channel-attn -- the 82586 won't start. */
outb(0, ioaddr + SIGNAL_CA);
}
/* Disable loopback and enable interrupts. */
outb(0x84, ioaddr + MISC_CTRL);
if (net_debug > 4)
pr_debug("%s: Initialized 82586, status %04x.\n", dev->name,
readw(shmem+iSCB_STATUS));
}
static void hardware_send_packet(struct net_device *dev, void *buf, short length, short pad)
{
struct net_local *lp = netdev_priv(dev);
short ioaddr = dev->base_addr;
ushort tx_block = lp->tx_head;
void __iomem *write_ptr = lp->base + tx_block;
static char padding[ETH_ZLEN];
/* Set the write pointer to the Tx block, and put out the header. */
writew(0x0000,write_ptr); /* Tx status */
writew(CMD_INTR|CmdTx,write_ptr+=2); /* Tx command */
writew(tx_block+16,write_ptr+=2); /* Next command is a NoOp. */
writew(tx_block+8,write_ptr+=2); /* Data Buffer offset. */
/* Output the data buffer descriptor. */
writew((pad + length) | 0x8000,write_ptr+=2); /* Byte count parameter. */
writew(-1,write_ptr+=2); /* No next data buffer. */
writew(tx_block+22+SCB_BASE,write_ptr+=2); /* Buffer follows the NoOp command. */
writew(0x0000,write_ptr+=2); /* Buffer address high bits (always zero). */
/* Output the Loop-back NoOp command. */
writew(0x0000,write_ptr+=2); /* Tx status */
writew(CmdNOp,write_ptr+=2); /* Tx command */
writew(tx_block+16,write_ptr+=2); /* Next is myself. */
/* Output the packet at the write pointer. */
memcpy_toio(write_ptr+2, buf, length);
if (pad)
memcpy_toio(write_ptr+length+2, padding, pad);
/* Set the old command link pointing to this send packet. */
writew(tx_block,lp->base + lp->tx_cmd_link);
lp->tx_cmd_link = tx_block + 20;
/* Set the next free tx region. */
lp->tx_head = tx_block + TX_BUF_SIZE;
if (lp->tx_head > RX_BUF_START - TX_BUF_SIZE)
lp->tx_head = TX_BUF_START;
if (net_debug > 4) {
pr_debug("%s: 3c507 @%x send length = %d, tx_block %3x, next %3x.\n",
dev->name, ioaddr, length, tx_block, lp->tx_head);
}
/* Grimly block further packets if there has been insufficient reaping. */
if (++lp->tx_pkts_in_ring < NUM_TX_BUFS)
netif_wake_queue(dev);
}
static void el16_rx(struct net_device *dev)
{
struct net_local *lp = netdev_priv(dev);
void __iomem *shmem = lp->base;
ushort rx_head = lp->rx_head;
ushort rx_tail = lp->rx_tail;
ushort boguscount = 10;
short frame_status;
while ((frame_status = readw(shmem+rx_head)) < 0) { /* Command complete */
void __iomem *read_frame = lp->base + rx_head;
ushort rfd_cmd = readw(read_frame+2);
ushort next_rx_frame = readw(read_frame+4);
ushort data_buffer_addr = readw(read_frame+6);
void __iomem *data_frame = lp->base + data_buffer_addr;
ushort pkt_len = readw(data_frame);
if (rfd_cmd != 0 || data_buffer_addr != rx_head + 22 ||
(pkt_len & 0xC000) != 0xC000) {
pr_err("%s: Rx frame at %#x corrupted, "
"status %04x cmd %04x next %04x "
"data-buf @%04x %04x.\n",
dev->name, rx_head, frame_status, rfd_cmd,
next_rx_frame, data_buffer_addr, pkt_len);
} else if ((frame_status & 0x2000) == 0) {
/* Frame Rxed, but with error. */
dev->stats.rx_errors++;
if (frame_status & 0x0800) dev->stats.rx_crc_errors++;
if (frame_status & 0x0400) dev->stats.rx_frame_errors++;
if (frame_status & 0x0200) dev->stats.rx_fifo_errors++;
if (frame_status & 0x0100) dev->stats.rx_over_errors++;
if (frame_status & 0x0080) dev->stats.rx_length_errors++;
} else {
/* Malloc up new buffer. */
struct sk_buff *skb;
pkt_len &= 0x3fff;
skb = netdev_alloc_skb(dev, pkt_len + 2);
if (skb == NULL) {
pr_err("%s: Memory squeeze, dropping packet.\n",
dev->name);
dev->stats.rx_dropped++;
break;
}
skb_reserve(skb,2);
/* 'skb->data' points to the start of sk_buff data area. */
memcpy_fromio(skb_put(skb,pkt_len), data_frame + 10, pkt_len);
skb->protocol=eth_type_trans(skb,dev);
netif_rx(skb);
dev->stats.rx_packets++;
dev->stats.rx_bytes += pkt_len;
}
/* Clear the status word and set End-of-List on the rx frame. */
writew(0,read_frame);
writew(0xC000,read_frame+2);
/* Clear the end-of-list on the prev. RFD. */
writew(0x0000,lp->base + rx_tail + 2);
rx_tail = rx_head;
rx_head = next_rx_frame;
if (--boguscount == 0)
break;
}
lp->rx_head = rx_head;
lp->rx_tail = rx_tail;
}
static void netdev_get_drvinfo(struct net_device *dev,
struct ethtool_drvinfo *info)
{
strlcpy(info->driver, DRV_NAME, sizeof(info->driver));
strlcpy(info->version, DRV_VERSION, sizeof(info->version));
snprintf(info->bus_info, sizeof(info->bus_info), "ISA 0x%lx",
dev->base_addr);
}
static u32 netdev_get_msglevel(struct net_device *dev)
{
return debug;
}
static void netdev_set_msglevel(struct net_device *dev, u32 level)
{
debug = level;
}
static const struct ethtool_ops netdev_ethtool_ops = {
.get_drvinfo = netdev_get_drvinfo,
.get_msglevel = netdev_get_msglevel,
.set_msglevel = netdev_set_msglevel,
};
#ifdef MODULE
static struct net_device *dev_3c507;
module_param(io, int, 0);
module_param(irq, int, 0);
MODULE_PARM_DESC(io, "EtherLink16 I/O base address");
MODULE_PARM_DESC(irq, "(ignored)");
int __init init_module(void)
{
if (io == 0)
pr_notice("3c507: You should not use auto-probing with insmod!\n");
dev_3c507 = el16_probe(-1);
return IS_ERR(dev_3c507) ? PTR_ERR(dev_3c507) : 0;
}
void __exit
cleanup_module(void)
{
struct net_device *dev = dev_3c507;
unregister_netdev(dev);
free_irq(dev->irq, dev);
iounmap(((struct net_local *)netdev_priv(dev))->base);
release_region(dev->base_addr, EL16_IO_EXTENT);
free_netdev(dev);
}
#endif /* MODULE */
MODULE_LICENSE("GPL");
...@@ -20,29 +20,6 @@ config NET_VENDOR_I825XX ...@@ -20,29 +20,6 @@ config NET_VENDOR_I825XX
if NET_VENDOR_I825XX if NET_VENDOR_I825XX
config ELPLUS
tristate "3c505 \"EtherLink Plus\" support"
depends on ISA && ISA_DMA_API
---help---
Information about this network (Ethernet) card can be found in
<file:Documentation/networking/3c505.txt>. If you have a card of
this type, say Y and read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here. The module
will be called 3c505.
config EL16
tristate "3c507 \"EtherLink 16\" support (EXPERIMENTAL)"
depends on ISA && EXPERIMENTAL
---help---
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here. The module
will be called 3c507.
config ARM_ETHER1 config ARM_ETHER1
tristate "Acorn Ether1 support" tristate "Acorn Ether1 support"
depends on ARM && ARCH_ACORN depends on ARM && ARCH_ACORN
......
...@@ -5,8 +5,6 @@ ...@@ -5,8 +5,6 @@
obj-$(CONFIG_ARM_ETHER1) += ether1.o obj-$(CONFIG_ARM_ETHER1) += ether1.o
obj-$(CONFIG_EEXPRESS) += eexpress.o obj-$(CONFIG_EEXPRESS) += eexpress.o
obj-$(CONFIG_EEXPRESS_PRO) += eepro.o obj-$(CONFIG_EEXPRESS_PRO) += eepro.o
obj-$(CONFIG_ELPLUS) += 3c505.o
obj-$(CONFIG_EL16) += 3c507.o
obj-$(CONFIG_NI52) += ni52.o obj-$(CONFIG_NI52) += ni52.o
obj-$(CONFIG_SUN3_82586) += sun3_82586.o obj-$(CONFIG_SUN3_82586) += sun3_82586.o
obj-$(CONFIG_ZNET) += znet.o obj-$(CONFIG_ZNET) += znet.o
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment