Merge tag 'mmc-updates-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc

Pull MMC updates from Chris Ball:
 "MMC highlights for 3.8:

  Core:
   - Expose access to the eMMC RPMB ("Replay Protected Memory Block")
     area by extending the existing mmc_block ioctl.
   - Add SDIO powered-suspend DT properties to the core MMC DT binding.
   - Add no-1-8-v DT flag for boards where the SD controller reports
     that it supports 1.8V but the board itself has no way to switch to
     1.8V.
   - More work on switching to 1.8V UHS support using a vqmmc regulator.
   - Fix up a case where the slot-gpio helper may fail to reset the host
     controller properly if a card was removed during a transfer.
   - Fix several cases where a broken device could cause an infinite
     loop while we wait for a register to update.

  Drivers:
   - at91-mci: Remove obsolete driver, atmel-mci handles these devices
     now.
   - sdhci-dove: Allow using GPIOs for card-detect notifications.
   - sdhci-esdhc: Fix for recovering from ADMA errors on broken silicon.
   - sdhci-s3c: Add pinctrl support.
   - wmt-sdmmc: New driver for WonderMedia SD/MMC controllers."

* tag 'mmc-updates-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (65 commits)
  mmc: sdhci: implement the .card_event() method
  mmc: extend the slot-gpio card-detection to use host's .card_event() method
  mmc: add a card-event host operation
  mmc: sdhci-s3c: Fix compilation warning
  mmc: sdhci-pci: Enable SDHCI_CAN_DO_HISPD for Ricoh SDHCI controller
  mmc: sdhci-dove: allow GPIOs to be used for card detection on Dove
  mmc: sdhci-dove: use two-stage initialization for sdhci-pltfm
  mmc: sdhci-dove: use devm_clk_get()
  mmc: eSDHC: Recover from ADMA errors
  mmc: dw_mmc: remove duplicated buswidth code
  mmc: dw_mmc: relocate where dw_mci_setup_bus() is called from
  mmc: Limit MMC speed to 52MHz if not HS200
  mmc: dw_mmc: use devres functions in dw_mmc
  mmc: sh_mmcif: remove unneeded clock connection ID
  mmc: sh_mobile_sdhi: remove unneeded clock connection ID
  mmc: sh_mobile_sdhi: fix clock frequency printing
  mmc: Remove redundant null check before kfree in bus.c
  mmc: Remove redundant null check before kfree in sdio_bus.c
  mmc: sdhci-imx-esdhc: use more devm_* functions
  mmc: dt: add no-1-8-v device tree flag
  ...

Documentation/devicetree/bindings/mmc/mmc.txt

@@ -21,6 +21,12 @@ Optional properties:
 - cd-inverted: when present, polarity on the cd gpio line is inverted
 - wp-inverted: when present, polarity on the wp gpio line is inverted
 - max-frequency: maximum operating clock frequency
+- no-1-8-v: when present, denotes that 1.8v card voltage is not supported on
+  this system, even if the controller claims it is.
+
+Optional SDIO properties:
+- keep-power-in-suspend: Preserves card power during a suspend/resume cycle
+- enable-sdio-wakeup: Enables wake up of host system on SDIO IRQ assertion
 
 Example:
 
@@ -33,4 +39,6 @@ sdhci@ab000000 {
 	cd-inverted;
 	wp-gpios = <&gpio 70 0>;
 	max-frequency = <50000000>;
+	keep-power-in-suspend;
+	enable-sdio-wakeup;
 }

Documentation/devicetree/bindings/mmc/samsung-sdhci.txt

@@ -12,10 +12,6 @@ is used. The Samsung's SDHCI controller bindings extends this as listed below.
 [A] The property "samsung,cd-pinmux-gpio" can be used as stated in the
     "Optional Board Specific Properties" section below.
 
-[B] If core card-detect bindings and "samsung,cd-pinmux-gpio" property
-    is not specified, it is assumed that there is no card detection
-    mechanism used.
-
 Required SoC Specific Properties:
 - compatible: should be one of the following
   - "samsung,s3c6410-sdhci": For controllers compatible with s3c6410 sdhci
@@ -24,14 +20,18 @@ Required SoC Specific Properties:
     controller.
 
 Required Board Specific Properties:
-- gpios: Should specify the gpios used for clock, command and data lines. The
+- Samsung GPIO variant (will be completely replaced by pinctrl):
+  - gpios: Should specify the gpios used for clock, command and data lines. The
     gpio specifier format depends on the gpio controller.
+- Pinctrl variant (preferred if available):
+  - pinctrl-0: Should specify pin control groups used for this controller.
+  - pinctrl-names: Should contain only one value - "default".
 
 Optional Board Specific Properties:
 - samsung,cd-pinmux-gpio: Specifies the card detect line that is routed
   through a pinmux to the card-detect pin of the card slot. This property
   should be used only if none of the mmc core card-detect properties are
-  used.
+  used. Only for Samsung GPIO variant.
 
 Example:
 	sdhci@12530000 {
@@ -40,12 +40,18 @@ Example:
 		interrupts = <0 75 0>;
 		bus-width = <4>;
 		cd-gpios = <&gpk2 2 2 3 3>;
+
+		/* Samsung GPIO variant */
 		gpios = <&gpk2 0 2 0 3>,  /* clock line */
 			<&gpk2 1 2 0 3>,  /* command line */
 			<&gpk2 3 2 3 3>,  /* data line 0 */
 			<&gpk2 4 2 3 3>,  /* data line 1 */
 			<&gpk2 5 2 3 3>,  /* data line 2 */
 			<&gpk2 6 2 3 3>;  /* data line 3 */
+
+		/* Pinctrl variant */
+		pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4>;
+		pinctrl-names = "default";
 	};
 
 	Note: This example shows both SoC specific and board specific properties

Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt

@@ -19,6 +19,7 @@ ti,dual-volt: boolean, supports dual voltage cards
 "supply-name" examples are "vmmc", "vmmc_aux" etc
 ti,non-removable: non-removable slot (like eMMC)
 ti,needs-special-reset: Requires a special softreset sequence
+ti,needs-special-hs-handling: HSMMC IP needs special setting for handling High Speed
 
 Example:
 	mmc1: mmc@0x4809c000 {

Documentation/devicetree/bindings/mmc/vt8500-sdmmc.txt

+* Wondermedia WM8505/WM8650 SD/MMC Host Controller
+
+This file documents differences between the core properties described
+by mmc.txt and the properties used by the wmt-sdmmc driver.
+
+Required properties:
+- compatible: Should be "wm,wm8505-sdhc".
+- interrupts: Two interrupts are required - regular irq and dma irq.
+
+Optional properties:
+- sdon-inverted: SD_ON bit is inverted on the controller
+
+Examples:
+
+sdhc@d800a000 {
+	compatible = "wm,wm8505-sdhc";
+	reg = <0xd800a000 0x1000>;
+	interrupts = <20 21>;
+	clocks = <&sdhc>;
+	bus-width = <4>;
+	sdon-inverted;
+};
+

Documentation/mmc/mmc-dev-attrs.txt

@@ -25,6 +25,8 @@ All attributes are read-only.
 	serial			Product Serial Number (from CID Register)
 	erase_size		Erase group size
 	preferred_erase_size	Preferred erase size
+	raw_rpmb_size_mult	RPMB partition size
+	rel_sectors		Reliable write sector count
 
 Note on Erase Size and Preferred Erase Size:
 
@@ -65,6 +67,11 @@ Note on Erase Size and Preferred Erase Size:
 
 	"preferred_erase_size" is in bytes.
 
+Note on raw_rpmb_size_mult:
+	"raw_rpmb_size_mult" is a mutliple of 128kB block.
+	RPMB size in byte is calculated by using the following equation:
+	RPMB partition size = 128kB x raw_rpmb_size_mult
+
 SD/MMC/SDIO Clock Gating Attribute
 ==================================
 

MAINTAINERS

@@ -1237,6 +1237,7 @@ F:	drivers/video/wm8505fb*
 F:	drivers/video/wmt_ge_rops.*
 F:	drivers/tty/serial/vt8500_serial.c
 F:	drivers/rtc/rtc-vt8500-c
+F:	drivers/mmc/host/wmt-sdmmc.c
 
 ARM/ZIPIT Z2 SUPPORT
 M:	Marek Vasut <marek.vasut@gmail.com>
@@ -1368,14 +1369,6 @@ S:	Maintained
 F:	drivers/atm/
 F:	include/linux/atm*
 
-ATMEL AT91 MCI DRIVER
-M:	Ludovic Desroches <ludovic.desroches@atmel.com>
-L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-W:	http://www.atmel.com/products/AT91/
-W:	http://www.at91.com/
-S:	Maintained
-F:	drivers/mmc/host/at91_mci.c
-
 ATMEL AT91 / AT32 MCI DRIVER
 M:	Ludovic Desroches <ludovic.desroches@atmel.com>
 S:	Maintained

arch/arm/mach-at91/include/mach/board.h

@@ -70,16 +70,6 @@ struct at91_cf_data {
 extern void __init at91_add_device_cf(struct at91_cf_data *data);
 
  /* MMC / SD */
-  /* at91_mci platform config */
-struct at91_mmc_data {
-	int		det_pin;	/* card detect IRQ */
-	unsigned	slot_b:1;	/* uses Slot B */
-	unsigned	wire4:1;	/* (SD) supports DAT0..DAT3 */
-	int		wp_pin;		/* (SD) writeprotect detect */
-	int		vcc_pin;	/* power switching (high == on) */
-};
-extern void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data);
-
   /* atmel-mci platform config */
 extern void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data);
 

arch/arm/plat-omap/include/plat/mmc.h

@@ -126,6 +126,7 @@ struct omap_mmc_platform_data {
 		/* we can put the features above into this variable */
 #define HSMMC_HAS_PBIAS		(1 << 0)
 #define HSMMC_HAS_UPDATED_RESET	(1 << 1)
+#define HSMMC_HAS_HSPE_SUPPORT	(1 << 2)
 		unsigned features;
 
 		int switch_pin;			/* gpio (card detect) */

drivers/mmc/card/block.c

@@ -57,6 +57,7 @@ MODULE_ALIAS("mmc:block");
 #define INAND_CMD38_ARG_SECERASE 0x80
 #define INAND_CMD38_ARG_SECTRIM1 0x81
 #define INAND_CMD38_ARG_SECTRIM2 0x88
+#define MMC_BLK_TIMEOUT_MS  (10 * 60 * 1000)        /* 10 minute timeout */
 
 static DEFINE_MUTEX(block_mutex);
 
@@ -126,6 +127,10 @@ enum mmc_blk_status {
 module_param(perdev_minors, int, 0444);
 MODULE_PARM_DESC(perdev_minors, "Minors numbers to allocate per device");
 
+static inline int mmc_blk_part_switch(struct mmc_card *card,
+				      struct mmc_blk_data *md);
+static int get_card_status(struct mmc_card *card, u32 *status, int retries);
+
 static struct mmc_blk_data *mmc_blk_get(struct gendisk *disk)
 {
 	struct mmc_blk_data *md;
@@ -357,6 +362,38 @@ static struct mmc_blk_ioc_data *mmc_blk_ioctl_copy_from_user(
 	return ERR_PTR(err);
 }
 
+static int ioctl_rpmb_card_status_poll(struct mmc_card *card, u32 *status,
+				       u32 retries_max)
+{
+	int err;
+	u32 retry_count = 0;
+
+	if (!status || !retries_max)
+		return -EINVAL;
+
+	do {
+		err = get_card_status(card, status, 5);
+		if (err)
+			break;
+
+		if (!R1_STATUS(*status) &&
+				(R1_CURRENT_STATE(*status) != R1_STATE_PRG))
+			break; /* RPMB programming operation complete */
+
+		/*
+		 * Rechedule to give the MMC device a chance to continue
+		 * processing the previous command without being polled too
+		 * frequently.
+		 */
+		usleep_range(1000, 5000);
+	} while (++retry_count < retries_max);
+
+	if (retry_count == retries_max)
+		err = -EPERM;
+
+	return err;
+}
+
 static int mmc_blk_ioctl_cmd(struct block_device *bdev,
 	struct mmc_ioc_cmd __user *ic_ptr)
 {
@@ -368,6 +405,8 @@ static int mmc_blk_ioctl_cmd(struct block_device *bdev,
 	struct mmc_request mrq = {NULL};
 	struct scatterlist sg;
 	int err;
+	int is_rpmb = false;
+	u32 status = 0;
 
 	/*
 	 * The caller must have CAP_SYS_RAWIO, and must be calling this on the
@@ -387,6 +426,9 @@ static int mmc_blk_ioctl_cmd(struct block_device *bdev,
 		goto cmd_err;
 	}
 
+	if (md->area_type & MMC_BLK_DATA_AREA_RPMB)
+		is_rpmb = true;
+
 	card = md->queue.card;
 	if (IS_ERR(card)) {
 		err = PTR_ERR(card);
@@ -437,12 +479,23 @@ static int mmc_blk_ioctl_cmd(struct block_device *bdev,
 
 	mmc_claim_host(card->host);
 
+	err = mmc_blk_part_switch(card, md);
+	if (err)
+		goto cmd_rel_host;
+
 	if (idata->ic.is_acmd) {
 		err = mmc_app_cmd(card->host, card);
 		if (err)
 			goto cmd_rel_host;
 	}
 
+	if (is_rpmb) {
+		err = mmc_set_blockcount(card, data.blocks,
+			idata->ic.write_flag & (1 << 31));
+		if (err)
+			goto cmd_rel_host;
+	}
+
 	mmc_wait_for_req(card->host, &mrq);
 
 	if (cmd.error) {
@@ -478,6 +531,18 @@ static int mmc_blk_ioctl_cmd(struct block_device *bdev,
 		}
 	}
 
+	if (is_rpmb) {
+		/*
+		 * Ensure RPMB command has completed by polling CMD13
+		 * "Send Status".
+		 */
+		err = ioctl_rpmb_card_status_poll(card, &status, 5);
+		if (err)
+			dev_err(mmc_dev(card->host),
+					"%s: Card Status=0x%08X, error %d\n",
+					__func__, status, err);
+	}
+
 cmd_rel_host:
 	mmc_release_host(card->host);
 
@@ -1034,6 +1099,9 @@ static int mmc_blk_err_check(struct mmc_card *card,
 	 */
 	if (!mmc_host_is_spi(card->host) && rq_data_dir(req) != READ) {
 		u32 status;
+		unsigned long timeout;
+
+		timeout = jiffies + msecs_to_jiffies(MMC_BLK_TIMEOUT_MS);
 		do {
 			int err = get_card_status(card, &status, 5);
 			if (err) {
@@ -1041,6 +1109,17 @@ static int mmc_blk_err_check(struct mmc_card *card,
 				       req->rq_disk->disk_name, err);
 				return MMC_BLK_CMD_ERR;
 			}
+
+			/* Timeout if the device never becomes ready for data
+			 * and never leaves the program state.
+			 */
+			if (time_after(jiffies, timeout)) {
+				pr_err("%s: Card stuck in programming state!"\
+					" %s %s\n", mmc_hostname(card->host),
+					req->rq_disk->disk_name, __func__);
+
+				return MMC_BLK_CMD_ERR;
+			}
 			/*
 			 * Some cards mishandle the status bits,
 			 * so make sure to check both the busy
@@ -1504,6 +1583,8 @@ static struct mmc_blk_data *mmc_blk_alloc_req(struct mmc_card *card,
 	md->disk->queue = md->queue.queue;
 	md->disk->driverfs_dev = parent;
 	set_disk_ro(md->disk, md->read_only || default_ro);
+	if (area_type & MMC_BLK_DATA_AREA_RPMB)
+		md->disk->flags |= GENHD_FL_NO_PART_SCAN;
 
 	/*
 	 * As discussed on lkml, GENHD_FL_REMOVABLE should:

drivers/mmc/card/queue.c

@@ -68,6 +68,16 @@ static int mmc_queue_thread(void *d)
 		if (req || mq->mqrq_prev->req) {
 			set_current_state(TASK_RUNNING);
 			mq->issue_fn(mq, req);
+
+			/*
+			 * Current request becomes previous request
+			 * and vice versa.
+			 */
+			mq->mqrq_prev->brq.mrq.data = NULL;
+			mq->mqrq_prev->req = NULL;
+			tmp = mq->mqrq_prev;
+			mq->mqrq_prev = mq->mqrq_cur;
+			mq->mqrq_cur = tmp;
 		} else {
 			if (kthread_should_stop()) {
 				set_current_state(TASK_RUNNING);
@@ -77,13 +87,6 @@ static int mmc_queue_thread(void *d)
 			schedule();
 			down(&mq->thread_sem);
 		}
-
-		/* Current request becomes previous request and vice versa. */
-		mq->mqrq_prev->brq.mrq.data = NULL;
-		mq->mqrq_prev->req = NULL;
-		tmp = mq->mqrq_prev;
-		mq->mqrq_prev = mq->mqrq_cur;
-		mq->mqrq_cur = tmp;
 	} while (1);
 	up(&mq->thread_sem);
 

drivers/mmc/core/bus.c

@@ -225,7 +225,6 @@ static void mmc_release_card(struct device *dev)
 
 	sdio_free_common_cis(card);
 
-	if (card->info)
 	kfree(card->info);
 
 	kfree(card);

drivers/mmc/core/core.c

@@ -42,6 +42,9 @@
 #include "sd_ops.h"
 #include "sdio_ops.h"
 
+/* If the device is not responding */
+#define MMC_CORE_TIMEOUT_MS	(10 * 60 * 1000) /* 10 minute timeout */
+
 /*
  * Background operations can take a long time, depending on the housekeeping
  * operations the card has to perform.
@@ -1631,6 +1634,7 @@ static int mmc_do_erase(struct mmc_card *card, unsigned int from,
 {
 	struct mmc_command cmd = {0};
 	unsigned int qty = 0;
+	unsigned long timeout;
 	int err;
 
 	/*
@@ -1708,6 +1712,7 @@ static int mmc_do_erase(struct mmc_card *card, unsigned int from,
 	if (mmc_host_is_spi(card->host))
 		goto out;
 
+	timeout = jiffies + msecs_to_jiffies(MMC_CORE_TIMEOUT_MS);
 	do {
 		memset(&cmd, 0, sizeof(struct mmc_command));
 		cmd.opcode = MMC_SEND_STATUS;
@@ -1721,8 +1726,19 @@ static int mmc_do_erase(struct mmc_card *card, unsigned int from,
 			err = -EIO;
 			goto out;
 		}
+
+		/* Timeout if the device never becomes ready for data and
+		 * never leaves the program state.
+		 */
+		if (time_after(jiffies, timeout)) {
+			pr_err("%s: Card stuck in programming state! %s\n",
+				mmc_hostname(card->host), __func__);
+			err =  -EIO;
+			goto out;
+		}
+
 	} while (!(cmd.resp[0] & R1_READY_FOR_DATA) ||
-		 R1_CURRENT_STATE(cmd.resp[0]) == R1_STATE_PRG);
+		 (R1_CURRENT_STATE(cmd.resp[0]) == R1_STATE_PRG));
 out:
 	return err;
 }
@@ -1942,6 +1958,20 @@ int mmc_set_blocklen(struct mmc_card *card, unsigned int blocklen)
 }
 EXPORT_SYMBOL(mmc_set_blocklen);
 
+int mmc_set_blockcount(struct mmc_card *card, unsigned int blockcount,
+			bool is_rel_write)
+{
+	struct mmc_command cmd = {0};
+
+	cmd.opcode = MMC_SET_BLOCK_COUNT;
+	cmd.arg = blockcount & 0x0000FFFF;
+	if (is_rel_write)
+		cmd.arg |= 1 << 31;
+	cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC;
+	return mmc_wait_for_cmd(card->host, &cmd, 5);
+}
+EXPORT_SYMBOL(mmc_set_blockcount);
+
 static void mmc_hw_reset_for_init(struct mmc_host *host)
 {
 	if (!(host->caps & MMC_CAP_HW_RESET) || !host->ops->hw_reset)

drivers/mmc/core/debugfs.c

@@ -144,6 +144,22 @@ static int mmc_ios_show(struct seq_file *s, void *data)
 	}
 	seq_printf(s, "timing spec:\t%u (%s)\n", ios->timing, str);
 
+	switch (ios->signal_voltage) {
+	case MMC_SIGNAL_VOLTAGE_330:
+		str = "3.30 V";
+		break;
+	case MMC_SIGNAL_VOLTAGE_180:
+		str = "1.80 V";
+		break;
+	case MMC_SIGNAL_VOLTAGE_120:
+		str = "1.20 V";
+		break;
+	default:
+		str = "invalid";
+		break;
+	}
+	seq_printf(s, "signal voltage:\t%u (%s)\n", ios->chip_select, str);
+
 	return 0;
 }
 

drivers/mmc/core/mmc.c

@@ -239,7 +239,7 @@ static void mmc_select_card_type(struct mmc_card *card)
 {
 	struct mmc_host *host = card->host;
 	u8 card_type = card->ext_csd.raw_card_type & EXT_CSD_CARD_TYPE_MASK;
-	unsigned int caps = host->caps, caps2 = host->caps2;
+	u32 caps = host->caps, caps2 = host->caps2;
 	unsigned int hs_max_dtr = 0;
 
 	if (card_type & EXT_CSD_CARD_TYPE_26)
@@ -491,6 +491,17 @@ static int mmc_read_ext_csd(struct mmc_card *card, u8 *ext_csd)
 
 		card->ext_csd.rel_param = ext_csd[EXT_CSD_WR_REL_PARAM];
 		card->ext_csd.rst_n_function = ext_csd[EXT_CSD_RST_N_FUNCTION];
+
+		/*
+		 * RPMB regions are defined in multiples of 128K.
+		 */
+		card->ext_csd.raw_rpmb_size_mult = ext_csd[EXT_CSD_RPMB_MULT];
+		if (ext_csd[EXT_CSD_RPMB_MULT]) {
+			mmc_part_add(card, ext_csd[EXT_CSD_RPMB_MULT] << 17,
+				EXT_CSD_PART_CONFIG_ACC_RPMB,
+				"rpmb", 0, false,
+				MMC_BLK_DATA_AREA_RPMB);
+		}
 	}
 
 	card->ext_csd.raw_erased_mem_count = ext_csd[EXT_CSD_ERASED_MEM_CONT];
@@ -615,6 +626,8 @@ MMC_DEV_ATTR(serial, "0x%08x\n", card->cid.serial);
 MMC_DEV_ATTR(enhanced_area_offset, "%llu\n",
 		card->ext_csd.enhanced_area_offset);
 MMC_DEV_ATTR(enhanced_area_size, "%u\n", card->ext_csd.enhanced_area_size);
+MMC_DEV_ATTR(raw_rpmb_size_mult, "%#x\n", card->ext_csd.raw_rpmb_size_mult);
+MMC_DEV_ATTR(rel_sectors, "%#x\n", card->ext_csd.rel_sectors);
 
 static struct attribute *mmc_std_attrs[] = {
 	&dev_attr_cid.attr,
@@ -630,6 +643,8 @@ static struct attribute *mmc_std_attrs[] = {
 	&dev_attr_serial.attr,
 	&dev_attr_enhanced_area_offset.attr,
 	&dev_attr_enhanced_area_size.attr,
+	&dev_attr_raw_rpmb_size_mult.attr,
+	&dev_attr_rel_sectors.attr,
 	NULL,
 };
 
@@ -1051,6 +1066,8 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
 	if (mmc_card_highspeed(card) || mmc_card_hs200(card)) {
 		if (max_dtr > card->ext_csd.hs_max_dtr)
 			max_dtr = card->ext_csd.hs_max_dtr;
+		if (mmc_card_highspeed(card) && (max_dtr > 52000000))
+			max_dtr = 52000000;
 	} else if (max_dtr > card->csd.max_dtr) {
 		max_dtr = card->csd.max_dtr;
 	}

drivers/mmc/core/mmc_ops.c

@@ -21,6 +21,8 @@
 #include "core.h"
 #include "mmc_ops.h"
 
+#define MMC_OPS_TIMEOUT_MS	(10 * 60 * 1000) /* 10 minute timeout */
+
 static int _mmc_select_card(struct mmc_host *host, struct mmc_card *card)
 {
 	int err;
@@ -409,6 +411,7 @@ int __mmc_switch(struct mmc_card *card, u8 set, u8 index, u8 value,
 {
 	int err;
 	struct mmc_command cmd = {0};
+	unsigned long timeout;
 	u32 status;
 
 	BUG_ON(!card);
@@ -437,6 +440,7 @@ int __mmc_switch(struct mmc_card *card, u8 set, u8 index, u8 value,
 		return 0;
 
 	/* Must check status to be sure of no errors */
+	timeout = jiffies + msecs_to_jiffies(MMC_OPS_TIMEOUT_MS);
 	do {
 		err = mmc_send_status(card, &status);
 		if (err)
@@ -445,6 +449,13 @@ int __mmc_switch(struct mmc_card *card, u8 set, u8 index, u8 value,
 			break;
 		if (mmc_host_is_spi(card->host))
 			break;
+
+		/* Timeout if the device never leaves the program state. */
+		if (time_after(jiffies, timeout)) {
+			pr_err("%s: Card stuck in programming state! %s\n",
+				mmc_hostname(card->host), __func__);
+			return -ETIMEDOUT;
+		}
 	} while (R1_CURRENT_STATE(status) == R1_STATE_PRG);
 
 	if (mmc_host_is_spi(card->host)) {

drivers/mmc/core/sdio_bus.c

@@ -193,7 +193,21 @@ static int sdio_bus_remove(struct device *dev)
 }
 
 #ifdef CONFIG_PM
+
+#ifdef CONFIG_PM_SLEEP
+static int pm_no_operation(struct device *dev)
+{
+	/*
+	 * Prevent the PM core from calling SDIO device drivers' suspend
+	 * callback routines, which it is not supposed to do, by using this
+	 * empty function as the bus type suspend callaback for SDIO.
+	 */
+	return 0;
+}
+#endif
+
 static const struct dev_pm_ops sdio_bus_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(pm_no_operation, pm_no_operation)
 	SET_RUNTIME_PM_OPS(
 		pm_generic_runtime_suspend,
 		pm_generic_runtime_resume,
@@ -258,7 +272,6 @@ static void sdio_release_func(struct device *dev)
 
 	sdio_free_func_cis(func);
 
-	if (func->info)
 	kfree(func->info);
 
 	kfree(func);

drivers/mmc/core/sdio_io.c

@@ -188,8 +188,7 @@ EXPORT_SYMBOL_GPL(sdio_set_block_size);
  */
 static inline unsigned int sdio_max_byte_size(struct sdio_func *func)
 {
-	unsigned mval =	min(func->card->host->max_seg_size,
-			    func->card->host->max_blk_size);
+	unsigned mval =	func->card->host->max_blk_size;
 
 	if (mmc_blksz_for_byte_mode(func->card))
 		mval = min(mval, func->cur_blksize);
@@ -311,11 +310,8 @@ static int sdio_io_rw_ext_helper(struct sdio_func *func, int write,
 	/* Do the bulk of the transfer using block mode (if supported). */
 	if (func->card->cccr.multi_block && (size > sdio_max_byte_size(func))) {
 		/* Blocks per command is limited by host count, host transfer
-		 * size (we only use a single sg entry) and the maximum for
-		 * IO_RW_EXTENDED of 511 blocks. */
-		max_blocks = min(func->card->host->max_blk_count,
-			func->card->host->max_seg_size / func->cur_blksize);
-		max_blocks = min(max_blocks, 511u);
+		 * size and the maximum for IO_RW_EXTENDED of 511 blocks. */
+		max_blocks = min(func->card->host->max_blk_count, 511u);
 
 		while (remainder >= func->cur_blksize) {
 			unsigned blocks;

drivers/mmc/core/sdio_ops.c

@@ -124,7 +124,10 @@ int mmc_io_rw_extended(struct mmc_card *card, int write, unsigned fn,
 	struct mmc_request mrq = {NULL};
 	struct mmc_command cmd = {0};
 	struct mmc_data data = {0};
-	struct scatterlist sg;
+	struct scatterlist sg, *sg_ptr;
+	struct sg_table sgtable;
+	unsigned int nents, left_size, i;
+	unsigned int seg_size = card->host->max_seg_size;
 
 	BUG_ON(!card);
 	BUG_ON(fn > 7);
@@ -152,15 +155,36 @@ int mmc_io_rw_extended(struct mmc_card *card, int write, unsigned fn,
 	/* Code in host drivers/fwk assumes that "blocks" always is >=1 */
 	data.blocks = blocks ? blocks : 1;
 	data.flags = write ? MMC_DATA_WRITE : MMC_DATA_READ;
+
+	left_size = data.blksz * data.blocks;
+	nents = (left_size - 1) / seg_size + 1;
+	if (nents > 1) {
+		if (sg_alloc_table(&sgtable, nents, GFP_KERNEL))
+			return -ENOMEM;
+
+		data.sg = sgtable.sgl;
+		data.sg_len = nents;
+
+		for_each_sg(data.sg, sg_ptr, data.sg_len, i) {
+			sg_set_page(sg_ptr, virt_to_page(buf + (i * seg_size)),
+					min(seg_size, left_size),
+					offset_in_page(buf + (i * seg_size)));
+			left_size = left_size - seg_size;
+		}
+	} else {
 		data.sg = &sg;
 		data.sg_len = 1;
 
-	sg_init_one(&sg, buf, data.blksz * data.blocks);
+		sg_init_one(&sg, buf, left_size);
+	}
 
 	mmc_set_data_timeout(&data, card);
 
 	mmc_wait_for_req(card->host, &mrq);
 
+	if (nents > 1)
+		sg_free_table(&sgtable);
+
 	if (cmd.error)
 		return cmd.error;
 	if (data.error)

drivers/mmc/core/slot-gpio.c

@@ -27,7 +27,13 @@ struct mmc_gpio {
 static irqreturn_t mmc_gpio_cd_irqt(int irq, void *dev_id)
 {
 	/* Schedule a card detection after a debounce timeout */
-	mmc_detect_change(dev_id, msecs_to_jiffies(100));
+	struct mmc_host *host = dev_id;
+
+	if (host->ops->card_event)
+		host->ops->card_event(host);
+
+	mmc_detect_change(host, msecs_to_jiffies(200));
+
 	return IRQ_HANDLED;
 }
 

drivers/mmc/host/Kconfig

@@ -270,26 +270,8 @@ config MMC_AU1X
 
 	  If unsure, say N.
 
-choice
-	prompt "Atmel SD/MMC Driver"
-	depends on AVR32 || ARCH_AT91
-	default MMC_ATMELMCI if AVR32
-	help
-	  Choose which driver to use for the Atmel MCI Silicon
-
-config MMC_AT91
-	tristate "AT91 SD/MMC Card Interface support (DEPRECATED)"
-	depends on ARCH_AT91
-	help
-	  This selects the AT91 MCI controller. This driver will
-	  be removed soon (for more information have a look to
-	  Documentation/feature-removal-schedule.txt). Please use
-	  MMC_ATMEL_MCI.
-
-	  If unsure, say N.
-
 config MMC_ATMELMCI
-	tristate "Atmel Multimedia Card Interface support"
+	tristate "Atmel SD/MMC Driver (Multimedia Card Interface)"
 	depends on AVR32 || ARCH_AT91
 	help
 	  This selects the Atmel Multimedia Card Interface driver. If
@@ -298,8 +280,6 @@ config MMC_ATMELMCI
 
 	  If unsure, say N.
 
-endchoice
-
 config MMC_ATMELMCI_DMA
 	bool "Atmel MCI DMA support"
 	depends on MMC_ATMELMCI && (AVR32 || ARCH_AT91SAM9G45) && DMA_ENGINE
@@ -621,3 +601,14 @@ config MMC_USHC
 
 	  Note: These controllers only support SDIO cards and do not
 	  support MMC or SD memory cards.
+
+config MMC_WMT
+	tristate "Wondermedia SD/MMC Host Controller support"
+	depends on ARCH_VT8500
+	default y
+	help
+	  This selects support for the SD/MMC Host Controller on
+	  Wondermedia WM8505/WM8650 based SoCs.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called wmt-sdmmc.

drivers/mmc/host/Makefile

@@ -17,7 +17,6 @@ obj-$(CONFIG_MMC_WBSD)		+= wbsd.o
 obj-$(CONFIG_MMC_AU1X)		+= au1xmmc.o
 obj-$(CONFIG_MMC_OMAP)		+= omap.o
 obj-$(CONFIG_MMC_OMAP_HS)	+= omap_hsmmc.o
-obj-$(CONFIG_MMC_AT91)		+= at91_mci.o
 obj-$(CONFIG_MMC_ATMELMCI)	+= atmel-mci.o
 obj-$(CONFIG_MMC_TIFM_SD)	+= tifm_sd.o
 obj-$(CONFIG_MMC_MSM)		+= msm_sdcc.o
@@ -45,6 +44,7 @@ obj-$(CONFIG_MMC_SH_MMCIF)	+= sh_mmcif.o
 obj-$(CONFIG_MMC_JZ4740)	+= jz4740_mmc.o
 obj-$(CONFIG_MMC_VUB300)	+= vub300.o
 obj-$(CONFIG_MMC_USHC)		+= ushc.o
+obj-$(CONFIG_MMC_WMT)		+= wmt-sdmmc.o
 
 obj-$(CONFIG_MMC_SDHCI_PLTFM)		+= sdhci-pltfm.o
 obj-$(CONFIG_MMC_SDHCI_CNS3XXX)		+= sdhci-cns3xxx.o

drivers/mmc/host/at91_mci.h

-/*
- * drivers/mmc/host/at91_mci.h
- *
- * Copyright (C) 2005 Ivan Kokshaysky
- * Copyright (C) SAN People
- *
- * MultiMedia Card Interface (MCI) registers.
- * Based on AT91RM9200 datasheet revision F.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef AT91_MCI_H
-#define AT91_MCI_H
-
-#define AT91_MCI_CR		0x00		/* Control Register */
-#define		AT91_MCI_MCIEN		(1 <<  0)	/* Multi-Media Interface Enable */
-#define		AT91_MCI_MCIDIS		(1 <<  1)	/* Multi-Media Interface Disable */
-#define		AT91_MCI_PWSEN		(1 <<  2)	/* Power Save Mode Enable */
-#define		AT91_MCI_PWSDIS		(1 <<  3)	/* Power Save Mode Disable */
-#define		AT91_MCI_SWRST		(1 <<  7)	/* Software Reset */
-
-#define AT91_MCI_MR		0x04		/* Mode Register */
-#define		AT91_MCI_CLKDIV		(0xff  <<  0)	/* Clock Divider */
-#define		AT91_MCI_PWSDIV		(7     <<  8)	/* Power Saving Divider */
-#define		AT91_MCI_RDPROOF	(1     << 11)	/* Read Proof Enable [SAM926[03] only] */
-#define		AT91_MCI_WRPROOF	(1     << 12)	/* Write Proof Enable [SAM926[03] only] */
-#define		AT91_MCI_PDCFBYTE	(1     << 13)	/* PDC Force Byte Transfer [SAM926[03] only] */
-#define		AT91_MCI_PDCPADV	(1     << 14)	/* PDC Padding Value */
-#define		AT91_MCI_PDCMODE	(1     << 15)	/* PDC-orientated Mode */
-#define		AT91_MCI_BLKLEN		(0xfff << 18)	/* Data Block Length */
-
-#define AT91_MCI_DTOR		0x08		/* Data Timeout Register */
-#define		AT91_MCI_DTOCYC		(0xf << 0)	/* Data Timeout Cycle Number */
-#define		AT91_MCI_DTOMUL		(7   << 4)	/* Data Timeout Multiplier */
-#define		AT91_MCI_DTOMUL_1		(0 <<  4)
-#define		AT91_MCI_DTOMUL_16		(1 <<  4)
-#define		AT91_MCI_DTOMUL_128		(2 <<  4)
-#define		AT91_MCI_DTOMUL_256		(3 <<  4)
-#define		AT91_MCI_DTOMUL_1K		(4 <<  4)
-#define		AT91_MCI_DTOMUL_4K		(5 <<  4)
-#define		AT91_MCI_DTOMUL_64K		(6 <<  4)
-#define		AT91_MCI_DTOMUL_1M		(7 <<  4)
-
-#define AT91_MCI_SDCR		0x0c		/* SD Card Register */
-#define		AT91_MCI_SDCSEL		(3 << 0)	/* SD Card Selector */
-#define		AT91_MCI_SDCBUS		(1 << 7)	/* 1-bit or 4-bit bus */
-
-#define AT91_MCI_ARGR		0x10		/* Argument Register */
-
-#define AT91_MCI_CMDR		0x14		/* Command Register */
-#define		AT91_MCI_CMDNB		(0x3f << 0)	/* Command Number */
-#define		AT91_MCI_RSPTYP		(3    << 6)	/* Response Type */
-#define			AT91_MCI_RSPTYP_NONE	(0 <<  6)
-#define			AT91_MCI_RSPTYP_48	(1 <<  6)
-#define			AT91_MCI_RSPTYP_136	(2 <<  6)
-#define		AT91_MCI_SPCMD		(7    << 8)	/* Special Command */
-#define			AT91_MCI_SPCMD_NONE	(0 <<  8)
-#define			AT91_MCI_SPCMD_INIT	(1 <<  8)
-#define			AT91_MCI_SPCMD_SYNC	(2 <<  8)
-#define			AT91_MCI_SPCMD_ICMD	(4 <<  8)
-#define			AT91_MCI_SPCMD_IRESP	(5 <<  8)
-#define		AT91_MCI_OPDCMD		(1 << 11)	/* Open Drain Command */
-#define		AT91_MCI_MAXLAT		(1 << 12)	/* Max Latency for Command to Response */
-#define		AT91_MCI_TRCMD		(3 << 16)	/* Transfer Command */
-#define			AT91_MCI_TRCMD_NONE	(0 << 16)
-#define			AT91_MCI_TRCMD_START	(1 << 16)
-#define			AT91_MCI_TRCMD_STOP	(2 << 16)
-#define		AT91_MCI_TRDIR		(1 << 18)	/* Transfer Direction */
-#define		AT91_MCI_TRTYP		(3 << 19)	/* Transfer Type */
-#define			AT91_MCI_TRTYP_BLOCK	(0 << 19)
-#define			AT91_MCI_TRTYP_MULTIPLE	(1 << 19)
-#define			AT91_MCI_TRTYP_STREAM	(2 << 19)
-#define			AT91_MCI_TRTYP_SDIO_BYTE	(4 << 19)
-#define			AT91_MCI_TRTYP_SDIO_BLOCK	(5 << 19)
-
-#define AT91_MCI_BLKR		0x18		/* Block Register */
-#define		AT91_MCI_BLKR_BCNT(n)	((0xffff & (n)) << 0)	/* Block count */
-#define		AT91_MCI_BLKR_BLKLEN(n)	((0xffff & (n)) << 16)	/* Block length */
-
-#define AT91_MCI_RSPR(n)	(0x20 + ((n) * 4))	/* Response Registers 0-3 */
-#define AT91_MCR_RDR		0x30		/* Receive Data Register */
-#define AT91_MCR_TDR		0x34		/* Transmit Data Register */
-
-#define AT91_MCI_SR		0x40		/* Status Register */
-#define		AT91_MCI_CMDRDY		(1 <<  0)	/* Command Ready */
-#define		AT91_MCI_RXRDY		(1 <<  1)	/* Receiver Ready */
-#define		AT91_MCI_TXRDY		(1 <<  2)	/* Transmit Ready */
-#define		AT91_MCI_BLKE		(1 <<  3)	/* Data Block Ended */
-#define		AT91_MCI_DTIP		(1 <<  4)	/* Data Transfer in Progress */
-#define		AT91_MCI_NOTBUSY	(1 <<  5)	/* Data Not Busy */
-#define		AT91_MCI_ENDRX		(1 <<  6)	/* End of RX Buffer */
-#define		AT91_MCI_ENDTX		(1 <<  7)	/* End fo TX Buffer */
-#define		AT91_MCI_SDIOIRQA	(1 <<  8)	/* SDIO Interrupt for Slot A */
-#define		AT91_MCI_SDIOIRQB	(1 <<  9)	/* SDIO Interrupt for Slot B */
-#define		AT91_MCI_RXBUFF		(1 << 14)	/* RX Buffer Full */
-#define		AT91_MCI_TXBUFE		(1 << 15)	/* TX Buffer Empty */
-#define		AT91_MCI_RINDE		(1 << 16)	/* Response Index Error */
-#define		AT91_MCI_RDIRE		(1 << 17)	/* Response Direction Error */
-#define		AT91_MCI_RCRCE		(1 << 18)	/* Response CRC Error */
-#define		AT91_MCI_RENDE		(1 << 19)	/* Response End Bit Error */
-#define		AT91_MCI_RTOE		(1 << 20)	/* Response Time-out Error */
-#define		AT91_MCI_DCRCE		(1 << 21)	/* Data CRC Error */
-#define		AT91_MCI_DTOE		(1 << 22)	/* Data Time-out Error */
-#define		AT91_MCI_OVRE		(1 << 30)	/* Overrun */
-#define		AT91_MCI_UNRE		(1 << 31)	/* Underrun */
-
-#define AT91_MCI_IER		0x44		/* Interrupt Enable Register */
-#define AT91_MCI_IDR		0x48		/* Interrupt Disable Register */
-#define AT91_MCI_IMR		0x4c		/* Interrupt Mask Register */
-
-#endif

drivers/mmc/host/dw_mmc-pci.c

@@ -134,7 +134,7 @@ static struct pci_driver dw_mci_pci_driver = {
 	.name		= "dw_mmc_pci",
 	.id_table	= dw_mci_pci_id,
 	.probe		= dw_mci_pci_probe,
-	.remove		= dw_mci_pci_remove,
+	.remove		= __devexit_p(dw_mci_pci_remove),
 	.driver		=	{
 		.pm =   &dw_mci_pci_pmops
 	},

drivers/mmc/host/dw_mmc-pltfm.c

@@ -119,7 +119,8 @@ static const struct of_device_id dw_mci_pltfm_match[] = {
 MODULE_DEVICE_TABLE(of, dw_mci_pltfm_match);
 
 static struct platform_driver dw_mci_pltfm_driver = {
-	.remove		= __exit_p(dw_mci_pltfm_remove),
+	.probe		= dw_mci_pltfm_probe,
+	.remove		= __devexit_p(dw_mci_pltfm_remove),
 	.driver		= {
 		.name		= "dw_mmc",
 		.of_match_table	= of_match_ptr(dw_mci_pltfm_match),
@@ -127,18 +128,7 @@ static struct platform_driver dw_mci_pltfm_driver = {
 	},
 };
 
-static int __init dw_mci_init(void)
-{
-	return platform_driver_probe(&dw_mci_pltfm_driver, dw_mci_pltfm_probe);
-}
-
-static void __exit dw_mci_exit(void)
-{
-	platform_driver_unregister(&dw_mci_pltfm_driver);
-}
-
-module_init(dw_mci_init);
-module_exit(dw_mci_exit);
+module_platform_driver(dw_mci_pltfm_driver);
 
 MODULE_DESCRIPTION("DW Multimedia Card Interface driver");
 MODULE_AUTHOR("NXP Semiconductor VietNam");

drivers/mmc/host/dw_mmc.c

@@ -232,7 +232,7 @@ static u32 dw_mci_prepare_command(struct mmc_host *mmc, struct mmc_command *cmd)
 {
 	struct mmc_data	*data;
 	struct dw_mci_slot *slot = mmc_priv(mmc);
-	struct dw_mci_drv_data *drv_data = slot->host->drv_data;
+	const struct dw_mci_drv_data *drv_data = slot->host->drv_data;
 	u32 cmdr;
 	cmd->error = -EINPROGRESS;
 
@@ -617,13 +617,13 @@ static void mci_send_cmd(struct dw_mci_slot *slot, u32 cmd, u32 arg)
 		cmd, arg, cmd_status);
 }
 
-static void dw_mci_setup_bus(struct dw_mci_slot *slot)
+static void dw_mci_setup_bus(struct dw_mci_slot *slot, bool force_clkinit)
 {
 	struct dw_mci *host = slot->host;
 	u32 div;
 	u32 clk_en_a;
 
-	if (slot->clock != host->current_speed) {
+	if (slot->clock != host->current_speed || force_clkinit) {
 		div = host->bus_hz / slot->clock;
 		if (host->bus_hz % slot->clock && host->bus_hz > slot->clock)
 			/*
@@ -683,9 +683,6 @@ static void __dw_mci_start_request(struct dw_mci *host,
 	if (host->pdata->select_slot)
 		host->pdata->select_slot(slot->id);
 
-	/* Slot specific timing and width adjustment */
-	dw_mci_setup_bus(slot);
-
 	host->cur_slot = slot;
 	host->mrq = mrq;
 
@@ -773,22 +770,19 @@ static void dw_mci_request(struct mmc_host *mmc, struct mmc_request *mrq)
 static void dw_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 {
 	struct dw_mci_slot *slot = mmc_priv(mmc);
-	struct dw_mci_drv_data *drv_data = slot->host->drv_data;
+	const struct dw_mci_drv_data *drv_data = slot->host->drv_data;
 	u32 regs;
 
-	/* set default 1 bit mode */
-	slot->ctype = SDMMC_CTYPE_1BIT;
-
 	switch (ios->bus_width) {
-	case MMC_BUS_WIDTH_1:
-		slot->ctype = SDMMC_CTYPE_1BIT;
-		break;
 	case MMC_BUS_WIDTH_4:
 		slot->ctype = SDMMC_CTYPE_4BIT;
 		break;
 	case MMC_BUS_WIDTH_8:
 		slot->ctype = SDMMC_CTYPE_8BIT;
 		break;
+	default:
+		/* set default 1 bit mode */
+		slot->ctype = SDMMC_CTYPE_1BIT;
 	}
 
 	regs = mci_readl(slot->host, UHS_REG);
@@ -812,6 +806,9 @@ static void dw_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 	if (drv_data && drv_data->set_ios)
 		drv_data->set_ios(slot->host, ios);
 
+	/* Slot specific timing and width adjustment */
+	dw_mci_setup_bus(slot, false);
+
 	switch (ios->power_mode) {
 	case MMC_POWER_UP:
 		set_bit(DW_MMC_CARD_NEED_INIT, &slot->flags);
@@ -1817,7 +1814,7 @@ static int dw_mci_init_slot(struct dw_mci *host, unsigned int id)
 {
 	struct mmc_host *mmc;
 	struct dw_mci_slot *slot;
-	struct dw_mci_drv_data *drv_data = host->drv_data;
+	const struct dw_mci_drv_data *drv_data = host->drv_data;
 	int ctrl_id, ret;
 	u8 bus_width;
 
@@ -1850,6 +1847,9 @@ static int dw_mci_init_slot(struct dw_mci *host, unsigned int id)
 	if (host->pdata->caps)
 		mmc->caps = host->pdata->caps;
 
+	if (host->pdata->pm_caps)
+		mmc->pm_caps = host->pdata->pm_caps;
+
 	if (host->dev->of_node) {
 		ctrl_id = of_alias_get_id(host->dev->of_node, "mshc");
 		if (ctrl_id < 0)
@@ -1911,7 +1911,7 @@ static int dw_mci_init_slot(struct dw_mci *host, unsigned int id)
 #endif /* CONFIG_MMC_DW_IDMAC */
 	}
 
-	host->vmmc = regulator_get(mmc_dev(mmc), "vmmc");
+	host->vmmc = devm_regulator_get(mmc_dev(mmc), "vmmc");
 	if (IS_ERR(host->vmmc)) {
 		pr_info("%s: no vmmc regulator found\n", mmc_hostname(mmc));
 		host->vmmc = NULL;
@@ -1960,7 +1960,7 @@ static void dw_mci_cleanup_slot(struct dw_mci_slot *slot, unsigned int id)
 static void dw_mci_init_dma(struct dw_mci *host)
 {
 	/* Alloc memory for sg translation */
-	host->sg_cpu = dma_alloc_coherent(host->dev, PAGE_SIZE,
+	host->sg_cpu = dmam_alloc_coherent(host->dev, PAGE_SIZE,
 					  &host->sg_dma, GFP_KERNEL);
 	if (!host->sg_cpu) {
 		dev_err(host->dev, "%s: could not alloc DMA memory\n",
@@ -2038,7 +2038,7 @@ static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)
 	struct dw_mci_board *pdata;
 	struct device *dev = host->dev;
 	struct device_node *np = dev->of_node;
-	struct dw_mci_drv_data *drv_data = host->drv_data;
+	const struct dw_mci_drv_data *drv_data = host->drv_data;
 	int idx, ret;
 
 	pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
@@ -2072,6 +2072,12 @@ static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)
 			return ERR_PTR(ret);
 	}
 
+	if (of_find_property(np, "keep-power-in-suspend", NULL))
+		pdata->pm_caps |= MMC_PM_KEEP_POWER;
+
+	if (of_find_property(np, "enable-sdio-wakeup", NULL))
+		pdata->pm_caps |= MMC_PM_WAKE_SDIO_IRQ;
+
 	return pdata;
 }
 
@@ -2084,7 +2090,7 @@ static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)
 
 int dw_mci_probe(struct dw_mci *host)
 {
-	struct dw_mci_drv_data *drv_data = host->drv_data;
+	const struct dw_mci_drv_data *drv_data = host->drv_data;
 	int width, i, ret = 0;
 	u32 fifo_size;
 	int init_slots = 0;
@@ -2103,26 +2109,24 @@ int dw_mci_probe(struct dw_mci *host)
 		return -ENODEV;
 	}
 
-	host->biu_clk = clk_get(host->dev, "biu");
+	host->biu_clk = devm_clk_get(host->dev, "biu");
 	if (IS_ERR(host->biu_clk)) {
 		dev_dbg(host->dev, "biu clock not available\n");
 	} else {
 		ret = clk_prepare_enable(host->biu_clk);
 		if (ret) {
 			dev_err(host->dev, "failed to enable biu clock\n");
-			clk_put(host->biu_clk);
 			return ret;
 		}
 	}
 
-	host->ciu_clk = clk_get(host->dev, "ciu");
+	host->ciu_clk = devm_clk_get(host->dev, "ciu");
 	if (IS_ERR(host->ciu_clk)) {
 		dev_dbg(host->dev, "ciu clock not available\n");
 	} else {
 		ret = clk_prepare_enable(host->ciu_clk);
 		if (ret) {
 			dev_err(host->dev, "failed to enable ciu clock\n");
-			clk_put(host->ciu_clk);
 			goto err_clk_biu;
 		}
 	}
@@ -2224,7 +2228,8 @@ int dw_mci_probe(struct dw_mci *host)
 	if (!host->card_workqueue)
 		goto err_dmaunmap;
 	INIT_WORK(&host->card_work, dw_mci_work_routine_card);
-	ret = request_irq(host->irq, dw_mci_interrupt, host->irq_flags, "dw-mci", host);
+	ret = devm_request_irq(host->dev, host->irq, dw_mci_interrupt,
+			       host->irq_flags, "dw-mci", host);
 	if (ret)
 		goto err_workqueue;
 
@@ -2262,7 +2267,7 @@ int dw_mci_probe(struct dw_mci *host)
 	} else {
 		dev_dbg(host->dev, "attempted to initialize %d slots, "
 					"but failed on all\n", host->num_slots);
-		goto err_init_slot;
+		goto err_workqueue;
 	}
 
 	/*
@@ -2282,33 +2287,24 @@ int dw_mci_probe(struct dw_mci *host)
 
 	return 0;
 
-err_init_slot:
-	free_irq(host->irq, host);
-
 err_workqueue:
 	destroy_workqueue(host->card_workqueue);
 
 err_dmaunmap:
 	if (host->use_dma && host->dma_ops->exit)
 		host->dma_ops->exit(host);
-	dma_free_coherent(host->dev, PAGE_SIZE,
-			  host->sg_cpu, host->sg_dma);
 
-	if (host->vmmc) {
+	if (host->vmmc)
 		regulator_disable(host->vmmc);
-		regulator_put(host->vmmc);
-	}
 
 err_clk_ciu:
-	if (!IS_ERR(host->ciu_clk)) {
+	if (!IS_ERR(host->ciu_clk))
 		clk_disable_unprepare(host->ciu_clk);
-		clk_put(host->ciu_clk);
-	}
+
 err_clk_biu:
-	if (!IS_ERR(host->biu_clk)) {
+	if (!IS_ERR(host->biu_clk))
 		clk_disable_unprepare(host->biu_clk);
-		clk_put(host->biu_clk);
-	}
+
 	return ret;
 }
 EXPORT_SYMBOL(dw_mci_probe);
@@ -2330,24 +2326,19 @@ void dw_mci_remove(struct dw_mci *host)
 	mci_writel(host, CLKENA, 0);
 	mci_writel(host, CLKSRC, 0);
 
-	free_irq(host->irq, host);
 	destroy_workqueue(host->card_workqueue);
-	dma_free_coherent(host->dev, PAGE_SIZE, host->sg_cpu, host->sg_dma);
 
 	if (host->use_dma && host->dma_ops->exit)
 		host->dma_ops->exit(host);
 
-	if (host->vmmc) {
+	if (host->vmmc)
 		regulator_disable(host->vmmc);
-		regulator_put(host->vmmc);
-	}
 
 	if (!IS_ERR(host->ciu_clk))
 		clk_disable_unprepare(host->ciu_clk);
+
 	if (!IS_ERR(host->biu_clk))
 		clk_disable_unprepare(host->biu_clk);
-	clk_put(host->ciu_clk);
-	clk_put(host->biu_clk);
 }
 EXPORT_SYMBOL(dw_mci_remove);
 
@@ -2411,6 +2402,11 @@ int dw_mci_resume(struct dw_mci *host)
 		struct dw_mci_slot *slot = host->slot[i];
 		if (!slot)
 			continue;
+		if (slot->mmc->pm_flags & MMC_PM_KEEP_POWER) {
+			dw_mci_set_ios(slot->mmc, &slot->mmc->ios);
+			dw_mci_setup_bus(slot, true);
+		}
+
 		ret = mmc_resume_host(host->slot[i]->mmc);
 		if (ret < 0)
 			return ret;

drivers/mmc/host/mxcmmc.c

@@ -240,7 +240,7 @@ static int mxcmci_setup_data(struct mxcmci_host *host, struct mmc_data *data)
 		return 0;
 
 	for_each_sg(data->sg, sg, data->sg_len, i) {
-		if (sg->offset & 3 || sg->length & 3) {
+		if (sg->offset & 3 || sg->length & 3 || sg->length < 512) {
 			host->do_dma = 0;
 			return 0;
 		}

drivers/mmc/host/mxs-mmc.c

@@ -43,7 +43,6 @@
 #include <linux/module.h>
 #include <linux/pinctrl/consumer.h>
 #include <linux/stmp_device.h>
-#include <linux/mmc/mxs-mmc.h>
 #include <linux/spi/mxs-spi.h>
 
 #define DRIVER_NAME	"mxs-mmc"
@@ -593,13 +592,13 @@ static int mxs_mmc_probe(struct platform_device *pdev)
 	struct mxs_mmc_host *host;
 	struct mmc_host *mmc;
 	struct resource *iores, *dmares;
-	struct mxs_mmc_platform_data *pdata;
 	struct pinctrl *pinctrl;
 	int ret = 0, irq_err, irq_dma;
 	dma_cap_mask_t mask;
 	struct regulator *reg_vmmc;
 	enum of_gpio_flags flags;
 	struct mxs_ssp *ssp;
+	u32 bus_width = 0;
 
 	iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	dmares = platform_get_resource(pdev, IORESOURCE_DMA, 0);
@@ -682,25 +681,15 @@ static int mxs_mmc_probe(struct platform_device *pdev)
 	mmc->caps = MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED |
 		    MMC_CAP_SDIO_IRQ | MMC_CAP_NEEDS_POLL;
 
-	pdata =	mmc_dev(host->mmc)->platform_data;
-	if (!pdata) {
-		u32 bus_width = 0;
 	of_property_read_u32(np, "bus-width", &bus_width);
 	if (bus_width == 4)
 		mmc->caps |= MMC_CAP_4_BIT_DATA;
 	else if (bus_width == 8)
 		mmc->caps |= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA;
-		host->wp_gpio = of_get_named_gpio_flags(np, "wp-gpios", 0,
-							&flags);
+	host->wp_gpio = of_get_named_gpio_flags(np, "wp-gpios", 0, &flags);
+
 	if (flags & OF_GPIO_ACTIVE_LOW)
 		host->wp_inverted = 1;
-	} else {
-		if (pdata->flags & SLOTF_8_BIT_CAPABLE)
-			mmc->caps |= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA;
-		if (pdata->flags & SLOTF_4_BIT_CAPABLE)
-			mmc->caps |= MMC_CAP_4_BIT_DATA;
-		host->wp_gpio = pdata->wp_gpio;
-	}
 
 	mmc->f_min = 400000;
 	mmc->f_max = 288000000;

drivers/mmc/host/sdhci-dove.c

@@ -19,20 +19,30 @@
  * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  */
 
-#include <linux/err.h>
-#include <linux/io.h>
 #include <linux/clk.h>
 #include <linux/err.h>
-#include <linux/module.h>
+#include <linux/gpio.h>
+#include <linux/io.h>
 #include <linux/mmc/host.h>
+#include <linux/module.h>
 #include <linux/of.h>
+#include <linux/of_gpio.h>
 
 #include "sdhci-pltfm.h"
 
 struct sdhci_dove_priv {
 	struct clk *clk;
+	int gpio_cd;
 };
 
+static irqreturn_t sdhci_dove_carddetect_irq(int irq, void *data)
+{
+	struct sdhci_host *host = data;
+
+	tasklet_schedule(&host->card_tasklet);
+	return IRQ_HANDLED;
+}
+
 static u16 sdhci_dove_readw(struct sdhci_host *host, int reg)
 {
 	u16 ret;
@@ -50,16 +60,25 @@ static u16 sdhci_dove_readw(struct sdhci_host *host, int reg)
 
 static u32 sdhci_dove_readl(struct sdhci_host *host, int reg)
 {
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct sdhci_dove_priv *priv = pltfm_host->priv;
 	u32 ret;
 
+	ret = readl(host->ioaddr + reg);
+
 	switch (reg) {
 	case SDHCI_CAPABILITIES:
-		ret = readl(host->ioaddr + reg);
 		/* Mask the support for 3.0V */
 		ret &= ~SDHCI_CAN_VDD_300;
 		break;
-	default:
-		ret = readl(host->ioaddr + reg);
+	case SDHCI_PRESENT_STATE:
+		if (gpio_is_valid(priv->gpio_cd)) {
+			if (gpio_get_value(priv->gpio_cd) == 0)
+				ret |= SDHCI_CARD_PRESENT;
+			else
+				ret &= ~SDHCI_CARD_PRESENT;
+		}
+		break;
 	}
 	return ret;
 }
@@ -92,25 +111,70 @@ static int __devinit sdhci_dove_probe(struct platform_device *pdev)
 		return -ENOMEM;
 	}
 
-	priv->clk = clk_get(&pdev->dev, NULL);
+	priv->clk = devm_clk_get(&pdev->dev, NULL);
+
+	if (pdev->dev.of_node) {
+		priv->gpio_cd = of_get_named_gpio(pdev->dev.of_node,
+						  "cd-gpios", 0);
+	} else {
+		priv->gpio_cd = -EINVAL;
+	}
+
+	if (gpio_is_valid(priv->gpio_cd)) {
+		ret = gpio_request(priv->gpio_cd, "sdhci-cd");
+		if (ret) {
+			dev_err(&pdev->dev, "card detect gpio request failed: %d\n",
+				ret);
+			return ret;
+		}
+		gpio_direction_input(priv->gpio_cd);
+	}
+
+	host = sdhci_pltfm_init(pdev, &sdhci_dove_pdata);
+	if (IS_ERR(host)) {
+		ret = PTR_ERR(host);
+		goto err_sdhci_pltfm_init;
+	}
+
+	pltfm_host = sdhci_priv(host);
+	pltfm_host->priv = priv;
+
 	if (!IS_ERR(priv->clk))
 		clk_prepare_enable(priv->clk);
 
-	ret = sdhci_pltfm_register(pdev, &sdhci_dove_pdata);
+	sdhci_get_of_property(pdev);
+
+	ret = sdhci_add_host(host);
 	if (ret)
-		goto sdhci_dove_register_fail;
+		goto err_sdhci_add;
 
-	host = platform_get_drvdata(pdev);
-	pltfm_host = sdhci_priv(host);
-	pltfm_host->priv = priv;
+	/*
+	 * We must request the IRQ after sdhci_add_host(), as the tasklet only
+	 * gets setup in sdhci_add_host() and we oops.
+	 */
+	if (gpio_is_valid(priv->gpio_cd)) {
+		ret = request_irq(gpio_to_irq(priv->gpio_cd),
+				  sdhci_dove_carddetect_irq,
+				  IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
+				  mmc_hostname(host->mmc), host);
+		if (ret) {
+			dev_err(&pdev->dev, "card detect irq request failed: %d\n",
+				ret);
+			goto err_request_irq;
+		}
+	}
 
 	return 0;
 
-sdhci_dove_register_fail:
-	if (!IS_ERR(priv->clk)) {
+err_request_irq:
+	sdhci_remove_host(host, 0);
+err_sdhci_add:
+	if (!IS_ERR(priv->clk))
 		clk_disable_unprepare(priv->clk);
-		clk_put(priv->clk);
-	}
+	sdhci_pltfm_free(pdev);
+err_sdhci_pltfm_init:
+	if (gpio_is_valid(priv->gpio_cd))
+		gpio_free(priv->gpio_cd);
 	return ret;
 }
 
@@ -122,10 +186,14 @@ static int __devexit sdhci_dove_remove(struct platform_device *pdev)
 
 	sdhci_pltfm_unregister(pdev);
 
-	if (!IS_ERR(priv->clk)) {
-		clk_disable_unprepare(priv->clk);
-		clk_put(priv->clk);
+	if (gpio_is_valid(priv->gpio_cd)) {
+		free_irq(gpio_to_irq(priv->gpio_cd), host);
+		gpio_free(priv->gpio_cd);
 	}
+
+	if (!IS_ERR(priv->clk))
+		clk_disable_unprepare(priv->clk);
+
 	return 0;
 }
 

drivers/mmc/host/sdhci-esdhc-imx.c

@@ -456,10 +456,10 @@ static int __devinit sdhci_esdhc_imx_probe(struct platform_device *pdev)
 
 	pltfm_host = sdhci_priv(host);
 
-	imx_data = kzalloc(sizeof(struct pltfm_imx_data), GFP_KERNEL);
+	imx_data = devm_kzalloc(&pdev->dev, sizeof(*imx_data), GFP_KERNEL);
 	if (!imx_data) {
 		err = -ENOMEM;
-		goto err_imx_data;
+		goto free_sdhci;
 	}
 
 	if (of_id)
@@ -470,19 +470,19 @@ static int __devinit sdhci_esdhc_imx_probe(struct platform_device *pdev)
 	imx_data->clk_ipg = devm_clk_get(&pdev->dev, "ipg");
 	if (IS_ERR(imx_data->clk_ipg)) {
 		err = PTR_ERR(imx_data->clk_ipg);
-		goto err_clk_get;
+		goto free_sdhci;
 	}
 
 	imx_data->clk_ahb = devm_clk_get(&pdev->dev, "ahb");
 	if (IS_ERR(imx_data->clk_ahb)) {
 		err = PTR_ERR(imx_data->clk_ahb);
-		goto err_clk_get;
+		goto free_sdhci;
 	}
 
 	imx_data->clk_per = devm_clk_get(&pdev->dev, "per");
 	if (IS_ERR(imx_data->clk_per)) {
 		err = PTR_ERR(imx_data->clk_per);
-		goto err_clk_get;
+		goto free_sdhci;
 	}
 
 	pltfm_host->clk = imx_data->clk_per;
@@ -494,7 +494,7 @@ static int __devinit sdhci_esdhc_imx_probe(struct platform_device *pdev)
 	imx_data->pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
 	if (IS_ERR(imx_data->pinctrl)) {
 		err = PTR_ERR(imx_data->pinctrl);
-		goto pin_err;
+		goto disable_clk;
 	}
 
 	host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;
@@ -519,7 +519,7 @@ static int __devinit sdhci_esdhc_imx_probe(struct platform_device *pdev)
 		if (!host->mmc->parent->platform_data) {
 			dev_err(mmc_dev(host->mmc), "no board data!\n");
 			err = -EINVAL;
-			goto no_board_data;
+			goto disable_clk;
 		}
 		imx_data->boarddata = *((struct esdhc_platform_data *)
 					host->mmc->parent->platform_data);
@@ -527,7 +527,8 @@ static int __devinit sdhci_esdhc_imx_probe(struct platform_device *pdev)
 
 	/* write_protect */
 	if (boarddata->wp_type == ESDHC_WP_GPIO) {
-		err = gpio_request_one(boarddata->wp_gpio, GPIOF_IN, "ESDHC_WP");
+		err = devm_gpio_request_one(&pdev->dev, boarddata->wp_gpio,
+					    GPIOF_IN, "ESDHC_WP");
 		if (err) {
 			dev_warn(mmc_dev(host->mmc),
 				 "no write-protect pin available!\n");
@@ -543,19 +544,21 @@ static int __devinit sdhci_esdhc_imx_probe(struct platform_device *pdev)
 
 	switch (boarddata->cd_type) {
 	case ESDHC_CD_GPIO:
-		err = gpio_request_one(boarddata->cd_gpio, GPIOF_IN, "ESDHC_CD");
+		err = devm_gpio_request_one(&pdev->dev, boarddata->cd_gpio,
+					    GPIOF_IN, "ESDHC_CD");
 		if (err) {
 			dev_err(mmc_dev(host->mmc),
 				"no card-detect pin available!\n");
-			goto no_card_detect_pin;
+			goto disable_clk;
 		}
 
-		err = request_irq(gpio_to_irq(boarddata->cd_gpio), cd_irq,
+		err = devm_request_irq(&pdev->dev,
+				 gpio_to_irq(boarddata->cd_gpio), cd_irq,
 				 IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
 				 mmc_hostname(host->mmc), host);
 		if (err) {
 			dev_err(mmc_dev(host->mmc), "request irq error\n");
-			goto no_card_detect_irq;
+			goto disable_clk;
 		}
 		/* fall through */
 
@@ -574,27 +577,15 @@ static int __devinit sdhci_esdhc_imx_probe(struct platform_device *pdev)
 
 	err = sdhci_add_host(host);
 	if (err)
-		goto err_add_host;
+		goto disable_clk;
 
 	return 0;
 
-err_add_host:
-	if (gpio_is_valid(boarddata->cd_gpio))
-		free_irq(gpio_to_irq(boarddata->cd_gpio), host);
-no_card_detect_irq:
-	if (gpio_is_valid(boarddata->cd_gpio))
-		gpio_free(boarddata->cd_gpio);
-	if (gpio_is_valid(boarddata->wp_gpio))
-		gpio_free(boarddata->wp_gpio);
-no_card_detect_pin:
-no_board_data:
-pin_err:
+disable_clk:
 	clk_disable_unprepare(imx_data->clk_per);
 	clk_disable_unprepare(imx_data->clk_ipg);
 	clk_disable_unprepare(imx_data->clk_ahb);
-err_clk_get:
-	kfree(imx_data);
-err_imx_data:
+free_sdhci:
 	sdhci_pltfm_free(pdev);
 	return err;
 }
@@ -604,25 +595,14 @@ static int __devexit sdhci_esdhc_imx_remove(struct platform_device *pdev)
 	struct sdhci_host *host = platform_get_drvdata(pdev);
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 	struct pltfm_imx_data *imx_data = pltfm_host->priv;
-	struct esdhc_platform_data *boarddata = &imx_data->boarddata;
 	int dead = (readl(host->ioaddr + SDHCI_INT_STATUS) == 0xffffffff);
 
 	sdhci_remove_host(host, dead);
 
-	if (gpio_is_valid(boarddata->wp_gpio))
-		gpio_free(boarddata->wp_gpio);
-
-	if (gpio_is_valid(boarddata->cd_gpio)) {
-		free_irq(gpio_to_irq(boarddata->cd_gpio), host);
-		gpio_free(boarddata->cd_gpio);
-	}
-
 	clk_disable_unprepare(imx_data->clk_per);
 	clk_disable_unprepare(imx_data->clk_ipg);
 	clk_disable_unprepare(imx_data->clk_ahb);
 
-	kfree(imx_data);
-
 	sdhci_pltfm_free(pdev);
 
 	return 0;

drivers/mmc/host/sdhci-of-esdhc.c

@@ -22,6 +22,7 @@
 #include "sdhci-esdhc.h"
 
 #define VENDOR_V_22	0x12
+#define VENDOR_V_23	0x13
 static u32 esdhc_readl(struct sdhci_host *host, int reg)
 {
 	u32 ret;
@@ -85,6 +86,18 @@ static u8 esdhc_readb(struct sdhci_host *host, int reg)
 	return ret;
 }
 
+static void esdhc_writel(struct sdhci_host *host, u32 val, int reg)
+{
+	/*
+	 * Enable IRQSTATEN[BGESEN] is just to set IRQSTAT[BGE]
+	 * when SYSCTL[RSTD]) is set for some special operations.
+	 * No any impact other operation.
+	 */
+	if (reg == SDHCI_INT_ENABLE)
+		val |= SDHCI_INT_BLK_GAP;
+	sdhci_be32bs_writel(host, val, reg);
+}
+
 static void esdhc_writew(struct sdhci_host *host, u16 val, int reg)
 {
 	if (reg == SDHCI_BLOCK_SIZE) {
@@ -121,6 +134,41 @@ static void esdhc_writeb(struct sdhci_host *host, u8 val, int reg)
 	sdhci_be32bs_writeb(host, val, reg);
 }
 
+/*
+ * For Abort or Suspend after Stop at Block Gap, ignore the ADMA
+ * error(IRQSTAT[ADMAE]) if both Transfer Complete(IRQSTAT[TC])
+ * and Block Gap Event(IRQSTAT[BGE]) are also set.
+ * For Continue, apply soft reset for data(SYSCTL[RSTD]);
+ * and re-issue the entire read transaction from beginning.
+ */
+static void esdhci_of_adma_workaround(struct sdhci_host *host, u32 intmask)
+{
+	u32 tmp;
+	bool applicable;
+	dma_addr_t dmastart;
+	dma_addr_t dmanow;
+
+	tmp = in_be32(host->ioaddr + SDHCI_SLOT_INT_STATUS);
+	tmp = (tmp & SDHCI_VENDOR_VER_MASK) >> SDHCI_VENDOR_VER_SHIFT;
+
+	applicable = (intmask & SDHCI_INT_DATA_END) &&
+		(intmask & SDHCI_INT_BLK_GAP) &&
+		(tmp == VENDOR_V_23);
+	if (!applicable)
+		return;
+
+	host->data->error = 0;
+	dmastart = sg_dma_address(host->data->sg);
+	dmanow = dmastart + host->data->bytes_xfered;
+	/*
+	 * Force update to the next DMA block boundary.
+	 */
+	dmanow = (dmanow & ~(SDHCI_DEFAULT_BOUNDARY_SIZE - 1)) +
+		SDHCI_DEFAULT_BOUNDARY_SIZE;
+	host->data->bytes_xfered = dmanow - dmastart;
+	sdhci_writel(host, dmanow, SDHCI_DMA_ADDRESS);
+}
+
 static int esdhc_of_enable_dma(struct sdhci_host *host)
 {
 	setbits32(host->ioaddr + ESDHC_DMA_SYSCTL, ESDHC_DMA_SNOOP);
@@ -177,13 +225,16 @@ static void esdhc_of_platform_init(struct sdhci_host *host)
 	vvn = (vvn & SDHCI_VENDOR_VER_MASK) >> SDHCI_VENDOR_VER_SHIFT;
 	if (vvn == VENDOR_V_22)
 		host->quirks2 |= SDHCI_QUIRK2_HOST_NO_CMD23;
+
+	if (vvn > VENDOR_V_22)
+		host->quirks &= ~SDHCI_QUIRK_NO_BUSY_IRQ;
 }
 
 static struct sdhci_ops sdhci_esdhc_ops = {
 	.read_l = esdhc_readl,
 	.read_w = esdhc_readw,
 	.read_b = esdhc_readb,
-	.write_l = sdhci_be32bs_writel,
+	.write_l = esdhc_writel,
 	.write_w = esdhc_writew,
 	.write_b = esdhc_writeb,
 	.set_clock = esdhc_of_set_clock,
@@ -195,6 +246,7 @@ static struct sdhci_ops sdhci_esdhc_ops = {
 	.platform_suspend = esdhc_of_suspend,
 	.platform_resume = esdhc_of_resume,
 #endif
+	.adma_workaround = esdhci_of_adma_workaround,
 };
 
 static struct sdhci_pltfm_data sdhci_esdhc_pdata = {

drivers/mmc/host/sdhci-pci.c

@@ -114,6 +114,7 @@ static int ricoh_mmc_probe_slot(struct sdhci_pci_slot *slot)
 
 		SDHCI_TIMEOUT_CLK_UNIT |
 		SDHCI_CAN_VDD_330 |
+		SDHCI_CAN_DO_HISPD |
 		SDHCI_CAN_DO_SDMA;
 	return 0;
 }

drivers/mmc/host/sdhci-pltfm.c

@@ -78,6 +78,9 @@ void sdhci_get_of_property(struct platform_device *pdev)
 		if (of_get_property(np, "broken-cd", NULL))
 			host->quirks |= SDHCI_QUIRK_BROKEN_CARD_DETECTION;
 
+		if (of_get_property(np, "no-1-8-v", NULL))
+			host->quirks2 |= SDHCI_QUIRK2_NO_1_8_V;
+
 		if (of_device_is_compatible(np, "fsl,p2020-rev1-esdhc"))
 			host->quirks |= SDHCI_QUIRK_BROKEN_DMA;
 
@@ -89,6 +92,12 @@ void sdhci_get_of_property(struct platform_device *pdev)
 		clk = of_get_property(np, "clock-frequency", &size);
 		if (clk && size == sizeof(*clk) && *clk)
 			pltfm_host->clock = be32_to_cpup(clk);
+
+		if (of_find_property(np, "keep-power-in-suspend", NULL))
+			host->mmc->pm_caps |= MMC_PM_KEEP_POWER;
+
+		if (of_find_property(np, "enable-sdio-wakeup", NULL))
+			host->mmc->pm_caps |= MMC_PM_WAKE_SDIO_IRQ;
 	}
 }
 #else

drivers/mmc/host/sdhci-pxav3.c

@@ -163,10 +163,18 @@ static int pxav3_set_uhs_signaling(struct sdhci_host *host, unsigned int uhs)
 	return 0;
 }
 
+static u32 pxav3_get_max_clock(struct sdhci_host *host)
+{
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+
+	return clk_get_rate(pltfm_host->clk);
+}
+
 static struct sdhci_ops pxav3_sdhci_ops = {
 	.platform_reset_exit = pxav3_set_private_registers,
 	.set_uhs_signaling = pxav3_set_uhs_signaling,
 	.platform_send_init_74_clocks = pxav3_gen_init_74_clocks,
+	.get_max_clock = pxav3_get_max_clock,
 };
 
 #ifdef CONFIG_OF
@@ -249,7 +257,8 @@ static int __devinit sdhci_pxav3_probe(struct platform_device *pdev)
 
 	host->quirks = SDHCI_QUIRK_BROKEN_TIMEOUT_VAL
 		| SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC
-		| SDHCI_QUIRK_32BIT_ADMA_SIZE;
+		| SDHCI_QUIRK_32BIT_ADMA_SIZE
+		| SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN;
 
 	/* enable 1/8V DDR capable */
 	host->mmc->caps |= MMC_CAP_1_8V_DDR;
@@ -271,6 +280,8 @@ static int __devinit sdhci_pxav3_probe(struct platform_device *pdev)
 
 		if (pdata->quirks)
 			host->quirks |= pdata->quirks;
+		if (pdata->quirks2)
+			host->quirks2 |= pdata->quirks2;
 		if (pdata->host_caps)
 			host->mmc->caps |= pdata->host_caps;
 		if (pdata->host_caps2)

drivers/mmc/host/sdhci-s3c.c

@@ -24,6 +24,7 @@
 #include <linux/of_gpio.h>
 #include <linux/pm.h>
 #include <linux/pm_runtime.h>
+#include <linux/pinctrl/consumer.h>
 
 #include <linux/mmc/host.h>
 
@@ -57,6 +58,7 @@ struct sdhci_s3c {
 	int			ext_cd_irq;
 	int			ext_cd_gpio;
 	int			*gpios;
+	struct pinctrl          *pctrl;
 
 	struct clk		*clk_io;
 	struct clk		*clk_bus[MAX_BUS_CLK];
@@ -373,7 +375,9 @@ static struct sdhci_ops sdhci_s3c_ops = {
 static void sdhci_s3c_notify_change(struct platform_device *dev, int state)
 {
 	struct sdhci_host *host = platform_get_drvdata(dev);
+#ifdef CONFIG_PM_RUNTIME
 	struct sdhci_s3c *sc = sdhci_priv(host);
+#endif
 	unsigned long flags;
 
 	if (host) {
@@ -413,7 +417,7 @@ static void sdhci_s3c_setup_card_detect_gpio(struct sdhci_s3c *sc)
 	struct s3c_sdhci_platdata *pdata = sc->pdata;
 	struct device *dev = &sc->pdev->dev;
 
-	if (gpio_request(pdata->ext_cd_gpio, "SDHCI EXT CD") == 0) {
+	if (devm_gpio_request(dev, pdata->ext_cd_gpio, "SDHCI EXT CD") == 0) {
 		sc->ext_cd_gpio = pdata->ext_cd_gpio;
 		sc->ext_cd_irq = gpio_to_irq(pdata->ext_cd_gpio);
 		if (sc->ext_cd_irq &&
@@ -456,12 +460,12 @@ static int __devinit sdhci_s3c_parse_dt(struct device *dev,
 		return -ENOMEM;
 
 	/* get the card detection method */
-	if (of_get_property(node, "broken-cd", 0)) {
+	if (of_get_property(node, "broken-cd", NULL)) {
 		pdata->cd_type = S3C_SDHCI_CD_NONE;
 		goto setup_bus;
 	}
 
-	if (of_get_property(node, "non-removable", 0)) {
+	if (of_get_property(node, "non-removable", NULL)) {
 		pdata->cd_type = S3C_SDHCI_CD_PERMANENT;
 		goto setup_bus;
 	}
@@ -484,8 +488,9 @@ static int __devinit sdhci_s3c_parse_dt(struct device *dev,
 		return -EINVAL;
 	}
 
-	dev_info(dev, "assuming no card detect line available\n");
-	pdata->cd_type = S3C_SDHCI_CD_NONE;
+	/* assuming internal card detect that will be configured by pinctrl */
+	pdata->cd_type = S3C_SDHCI_CD_INTERNAL;
+	goto setup_bus;
 
  found_cd:
 	if (pdata->cd_type == S3C_SDHCI_CD_GPIO) {
@@ -494,7 +499,7 @@ static int __devinit sdhci_s3c_parse_dt(struct device *dev,
 		if (of_get_property(node, "cd-inverted", NULL))
 			pdata->ext_cd_gpio_invert = 1;
 	} else if (pdata->cd_type == S3C_SDHCI_CD_INTERNAL) {
-		ret = gpio_request(gpio, "sdhci-cd");
+		ret = devm_gpio_request(dev, gpio, "sdhci-cd");
 		if (ret) {
 			dev_err(dev, "card detect gpio request failed\n");
 			return -EINVAL;
@@ -503,33 +508,28 @@ static int __devinit sdhci_s3c_parse_dt(struct device *dev,
 	}
 
  setup_bus:
+	if (!IS_ERR(ourhost->pctrl))
+		return 0;
+
 	/* get the gpios for command, clock and data lines */
 	for (cnt = 0; cnt < NUM_GPIOS(pdata->max_width); cnt++) {
 		gpio = of_get_gpio(node, cnt);
 		if (!gpio_is_valid(gpio)) {
 			dev_err(dev, "invalid gpio[%d]\n", cnt);
-			goto err_free_dt_cd_gpio;
+			return -EINVAL;
 		}
 		ourhost->gpios[cnt] = gpio;
 	}
 
 	for (cnt = 0; cnt < NUM_GPIOS(pdata->max_width); cnt++) {
-		ret = gpio_request(ourhost->gpios[cnt], "sdhci-gpio");
+		ret = devm_gpio_request(dev, ourhost->gpios[cnt], "sdhci-gpio");
 		if (ret) {
 			dev_err(dev, "gpio[%d] request failed\n", cnt);
-			goto err_free_dt_gpios;
+			return -EINVAL;
 		}
 	}
 
 	return 0;
-
- err_free_dt_gpios:
-	while (--cnt >= 0)
-		gpio_free(ourhost->gpios[cnt]);
- err_free_dt_cd_gpio:
-	if (pdata->cd_type == S3C_SDHCI_CD_INTERNAL)
-		gpio_free(ourhost->ext_cd_gpio);
-	return -EINVAL;
 }
 #else
 static int __devinit sdhci_s3c_parse_dt(struct device *dev,
@@ -586,13 +586,15 @@ static int __devinit sdhci_s3c_probe(struct platform_device *pdev)
 	pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
 	if (!pdata) {
 		ret = -ENOMEM;
-		goto err_pdata;
+		goto err_pdata_io_clk;
 	}
 
+	sc->pctrl = devm_pinctrl_get_select_default(&pdev->dev);
+
 	if (pdev->dev.of_node) {
 		ret = sdhci_s3c_parse_dt(&pdev->dev, host, pdata);
 		if (ret)
-			goto err_pdata;
+			goto err_pdata_io_clk;
 	} else {
 		memcpy(pdata, pdev->dev.platform_data, sizeof(*pdata));
 		sc->ext_cd_gpio = -1; /* invalid gpio number */
@@ -610,7 +612,7 @@ static int __devinit sdhci_s3c_probe(struct platform_device *pdev)
 	if (IS_ERR(sc->clk_io)) {
 		dev_err(dev, "failed to get io clock\n");
 		ret = PTR_ERR(sc->clk_io);
-		goto err_io_clk;
+		goto err_pdata_io_clk;
 	}
 
 	/* enable the local io clock and keep it running for the moment. */
@@ -773,13 +775,7 @@ static int __devinit sdhci_s3c_probe(struct platform_device *pdev)
 	clk_disable_unprepare(sc->clk_io);
 	clk_put(sc->clk_io);
 
- err_io_clk:
-	for (ptr = 0; ptr < NUM_GPIOS(sc->pdata->max_width); ptr++)
-		gpio_free(sc->gpios[ptr]);
-	if (pdata->cd_type == S3C_SDHCI_CD_INTERNAL)
-		gpio_free(sc->ext_cd_gpio);
-
- err_pdata:
+ err_pdata_io_clk:
 	sdhci_free_host(host);
 
 	return ret;
@@ -798,9 +794,6 @@ static int __devexit sdhci_s3c_remove(struct platform_device *pdev)
 	if (sc->ext_cd_irq)
 		free_irq(sc->ext_cd_irq, sc);
 
-	if (gpio_is_valid(sc->ext_cd_gpio))
-		gpio_free(sc->ext_cd_gpio);
-
 #ifdef CONFIG_PM_RUNTIME
 	if (pdata->cd_type != S3C_SDHCI_CD_INTERNAL)
 		clk_prepare_enable(sc->clk_io);
@@ -821,11 +814,6 @@ static int __devexit sdhci_s3c_remove(struct platform_device *pdev)
 	clk_disable_unprepare(sc->clk_io);
 	clk_put(sc->clk_io);
 
-	if (pdev->dev.of_node) {
-		for (ptr = 0; ptr < NUM_GPIOS(sc->pdata->max_width); ptr++)
-			gpio_free(sc->gpios[ptr]);
-	}
-
 	sdhci_free_host(host);
 	platform_set_drvdata(pdev, NULL);
 

drivers/mmc/host/sdhci-spear.c

@@ -146,6 +146,11 @@ static int __devinit sdhci_probe(struct platform_device *pdev)
 		goto put_clk;
 	}
 
+	ret = clk_set_rate(sdhci->clk, 50000000);
+	if (ret)
+		dev_dbg(&pdev->dev, "Error setting desired clk, clk=%lu\n",
+				clk_get_rate(sdhci->clk));
+
 	if (np) {
 		sdhci->data = sdhci_probe_config_dt(pdev);
 		if (IS_ERR(sdhci->data)) {
@@ -297,7 +302,7 @@ static int sdhci_suspend(struct device *dev)
 
 	ret = sdhci_suspend_host(host);
 	if (!ret)
-		clk_disable_unprepare(sdhci->clk);
+		clk_disable(sdhci->clk);
 
 	return ret;
 }
@@ -308,7 +313,7 @@ static int sdhci_resume(struct device *dev)
 	struct spear_sdhci *sdhci = dev_get_platdata(dev);
 	int ret;
 
-	ret = clk_prepare_enable(sdhci->clk);
+	ret = clk_enable(sdhci->clk);
 	if (ret) {
 		dev_dbg(dev, "Resume: Error enabling clock\n");
 		return ret;

drivers/mmc/host/sdhci.c

@@ -1618,7 +1618,7 @@ static int sdhci_do_3_3v_signal_voltage_switch(struct sdhci_host *host,
 	sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
 
 	if (host->vqmmc) {
-		ret = regulator_set_voltage(host->vqmmc, 3300000, 3300000);
+		ret = regulator_set_voltage(host->vqmmc, 2700000, 3600000);
 		if (ret) {
 			pr_warning("%s: Switching to 3.3V signalling voltage "
 				   " failed\n", mmc_hostname(host->mmc));
@@ -1662,7 +1662,7 @@ static int sdhci_do_1_8v_signal_voltage_switch(struct sdhci_host *host,
 		 */
 		if (host->vqmmc)
 			ret = regulator_set_voltage(host->vqmmc,
-				1800000, 1800000);
+				1700000, 1950000);
 		else
 			ret = 0;
 
@@ -1994,30 +1994,11 @@ static void sdhci_enable_preset_value(struct mmc_host *mmc, bool enable)
 	sdhci_runtime_pm_put(host);
 }
 
-static const struct mmc_host_ops sdhci_ops = {
-	.request	= sdhci_request,
-	.set_ios	= sdhci_set_ios,
-	.get_ro		= sdhci_get_ro,
-	.hw_reset	= sdhci_hw_reset,
-	.enable_sdio_irq = sdhci_enable_sdio_irq,
-	.start_signal_voltage_switch	= sdhci_start_signal_voltage_switch,
-	.execute_tuning			= sdhci_execute_tuning,
-	.enable_preset_value		= sdhci_enable_preset_value,
-};
-
-/*****************************************************************************\
- *                                                                           *
- * Tasklets                                                                  *
- *                                                                           *
-\*****************************************************************************/
-
-static void sdhci_tasklet_card(unsigned long param)
+static void sdhci_card_event(struct mmc_host *mmc)
 {
-	struct sdhci_host *host;
+	struct sdhci_host *host = mmc_priv(mmc);
 	unsigned long flags;
 
-	host = (struct sdhci_host*)param;
-
 	spin_lock_irqsave(&host->lock, flags);
 
 	/* Check host->mrq first in case we are runtime suspended */
@@ -2036,6 +2017,31 @@ static void sdhci_tasklet_card(unsigned long param)
 	}
 
 	spin_unlock_irqrestore(&host->lock, flags);
+}
+
+static const struct mmc_host_ops sdhci_ops = {
+	.request	= sdhci_request,
+	.set_ios	= sdhci_set_ios,
+	.get_ro		= sdhci_get_ro,
+	.hw_reset	= sdhci_hw_reset,
+	.enable_sdio_irq = sdhci_enable_sdio_irq,
+	.start_signal_voltage_switch	= sdhci_start_signal_voltage_switch,
+	.execute_tuning			= sdhci_execute_tuning,
+	.enable_preset_value		= sdhci_enable_preset_value,
+	.card_event			= sdhci_card_event,
+};
+
+/*****************************************************************************\
+ *                                                                           *
+ * Tasklets                                                                  *
+ *                                                                           *
+\*****************************************************************************/
+
+static void sdhci_tasklet_card(unsigned long param)
+{
+	struct sdhci_host *host = (struct sdhci_host*)param;
+
+	sdhci_card_event(host->mmc);
 
 	mmc_detect_change(host->mmc, msecs_to_jiffies(200));
 }
@@ -2282,6 +2288,8 @@ static void sdhci_data_irq(struct sdhci_host *host, u32 intmask)
 		pr_err("%s: ADMA error\n", mmc_hostname(host->mmc));
 		sdhci_show_adma_error(host);
 		host->data->error = -EIO;
+		if (host->ops->adma_workaround)
+			host->ops->adma_workaround(host, intmask);
 	}
 
 	if (host->data->error)
@@ -2858,10 +2866,16 @@ int sdhci_add_host(struct sdhci_host *host)
 				mmc_hostname(mmc));
 			host->vqmmc = NULL;
 		}
-	}
-	else if (regulator_is_supported_voltage(host->vqmmc, 1800000, 1800000))
+	} else {
 		regulator_enable(host->vqmmc);
-	else
+		if (!regulator_is_supported_voltage(host->vqmmc, 1700000,
+			1950000))
+			caps[1] &= ~(SDHCI_SUPPORT_SDR104 |
+					SDHCI_SUPPORT_SDR50 |
+					SDHCI_SUPPORT_DDR50);
+	}
+
+	if (host->quirks2 & SDHCI_QUIRK2_NO_1_8_V)
 		caps[1] &= ~(SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_SDR50 |
 		       SDHCI_SUPPORT_DDR50);
 
@@ -2919,21 +2933,18 @@ int sdhci_add_host(struct sdhci_host *host)
 				mmc_hostname(mmc));
 			host->vmmc = NULL;
 		}
-	} else
-		regulator_enable(host->vmmc);
+	}
 
 #ifdef CONFIG_REGULATOR
 	if (host->vmmc) {
-		ret = regulator_is_supported_voltage(host->vmmc, 3300000,
-			3300000);
+		ret = regulator_is_supported_voltage(host->vmmc, 2700000,
+			3600000);
 		if ((ret <= 0) || (!(caps[0] & SDHCI_CAN_VDD_330)))
 			caps[0] &= ~SDHCI_CAN_VDD_330;
-		ret = regulator_is_supported_voltage(host->vmmc, 3000000,
-			3000000);
 		if ((ret <= 0) || (!(caps[0] & SDHCI_CAN_VDD_300)))
 			caps[0] &= ~SDHCI_CAN_VDD_300;
-		ret = regulator_is_supported_voltage(host->vmmc, 1800000,
-			1800000);
+		ret = regulator_is_supported_voltage(host->vmmc, 1700000,
+			1950000);
 		if ((ret <= 0) || (!(caps[0] & SDHCI_CAN_VDD_180)))
 			caps[0] &= ~SDHCI_CAN_VDD_180;
 	}

drivers/mmc/host/sdhci.h

@@ -120,6 +120,7 @@
 #define SDHCI_SIGNAL_ENABLE	0x38
 #define  SDHCI_INT_RESPONSE	0x00000001
 #define  SDHCI_INT_DATA_END	0x00000002
+#define  SDHCI_INT_BLK_GAP	0x00000004
 #define  SDHCI_INT_DMA_END	0x00000008
 #define  SDHCI_INT_SPACE_AVAIL	0x00000010
 #define  SDHCI_INT_DATA_AVAIL	0x00000020
@@ -146,7 +147,8 @@
 #define  SDHCI_INT_DATA_MASK	(SDHCI_INT_DATA_END | SDHCI_INT_DMA_END | \
 		SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL | \
 		SDHCI_INT_DATA_TIMEOUT | SDHCI_INT_DATA_CRC | \
-		SDHCI_INT_DATA_END_BIT | SDHCI_INT_ADMA_ERROR)
+		SDHCI_INT_DATA_END_BIT | SDHCI_INT_ADMA_ERROR | \
+		SDHCI_INT_BLK_GAP)
 #define SDHCI_INT_ALL_MASK	((unsigned int)-1)
 
 #define SDHCI_ACMD12_ERR	0x3C
@@ -278,6 +280,7 @@ struct sdhci_ops {
 	void	(*hw_reset)(struct sdhci_host *host);
 	void	(*platform_suspend)(struct sdhci_host *host);
 	void	(*platform_resume)(struct sdhci_host *host);
+	void    (*adma_workaround)(struct sdhci_host *host, u32 intmask);
 	void	(*platform_init)(struct sdhci_host *host);
 };
 

drivers/mmc/host/sh_mmcif.c

@@ -1306,7 +1306,6 @@ static int __devinit sh_mmcif_probe(struct platform_device *pdev)
 	struct sh_mmcif_plat_data *pd = pdev->dev.platform_data;
 	struct resource *res;
 	void __iomem *reg;
-	char clk_name[8];
 
 	irq[0] = platform_get_irq(pdev, 0);
 	irq[1] = platform_get_irq(pdev, 1);
@@ -1356,11 +1355,10 @@ static int __devinit sh_mmcif_probe(struct platform_device *pdev)
 	pm_runtime_enable(&pdev->dev);
 	host->power = false;
 
-	snprintf(clk_name, sizeof(clk_name), "mmc%d", pdev->id);
-	host->hclk = clk_get(&pdev->dev, clk_name);
+	host->hclk = clk_get(&pdev->dev, NULL);
 	if (IS_ERR(host->hclk)) {
 		ret = PTR_ERR(host->hclk);
-		dev_err(&pdev->dev, "cannot get clock \"%s\": %d\n", clk_name, ret);
+		dev_err(&pdev->dev, "cannot get clock: %d\n", ret);
 		goto eclkget;
 	}
 	ret = sh_mmcif_clk_update(host);

drivers/mmc/host/sh_mobile_sdhi.c

@@ -123,7 +123,6 @@ static int __devinit sh_mobile_sdhi_probe(struct platform_device *pdev)
 	struct tmio_mmc_data *mmc_data;
 	struct sh_mobile_sdhi_info *p = pdev->dev.platform_data;
 	struct tmio_mmc_host *host;
-	char clk_name[8];
 	int irq, ret, i = 0;
 	bool multiplexed_isr = true;
 
@@ -144,11 +143,10 @@ static int __devinit sh_mobile_sdhi_probe(struct platform_device *pdev)
 		}
 	}
 
-	snprintf(clk_name, sizeof(clk_name), "sdhi%d", pdev->id);
-	priv->clk = clk_get(&pdev->dev, clk_name);
+	priv->clk = clk_get(&pdev->dev, NULL);
 	if (IS_ERR(priv->clk)) {
-		dev_err(&pdev->dev, "cannot get clock \"%s\"\n", clk_name);
 		ret = PTR_ERR(priv->clk);
+		dev_err(&pdev->dev, "cannot get clock: %d\n", ret);
 		goto eclkget;
 	}
 
@@ -250,7 +248,7 @@ static int __devinit sh_mobile_sdhi_probe(struct platform_device *pdev)
 	dev_info(&pdev->dev, "%s base at 0x%08lx clock rate %u MHz\n",
 		 mmc_hostname(host->mmc), (unsigned long)
 		 (platform_get_resource(pdev, IORESOURCE_MEM, 0)->start),
-		 mmc_data->hclk / 1000000);
+		 host->mmc->f_max / 1000000);
 
 	return ret;
 

drivers/mmc/host/vub300.c

@@ -2362,6 +2362,7 @@ static int vub300_probe(struct usb_interface *interface,
 error1:
 	usb_free_urb(command_out_urb);
 error0:
+	usb_put_dev(udev);
 	return retval;
 }
 

include/linux/mmc/card.h

@@ -85,6 +85,7 @@ struct mmc_ext_csd {
 	bool			boot_ro_lockable;
 	u8			raw_exception_status;	/* 53 */
 	u8			raw_partition_support;	/* 160 */
+	u8			raw_rpmb_size_mult;	/* 168 */
 	u8			raw_erased_mem_count;	/* 181 */
 	u8			raw_ext_csd_structure;	/* 194 */
 	u8			raw_card_type;		/* 196 */
@@ -206,6 +207,7 @@ struct mmc_part {
 #define MMC_BLK_DATA_AREA_MAIN	(1<<0)
 #define MMC_BLK_DATA_AREA_BOOT	(1<<1)
 #define MMC_BLK_DATA_AREA_GP	(1<<2)
+#define MMC_BLK_DATA_AREA_RPMB	(1<<3)
 };
 
 /*

include/linux/mmc/core.h

@@ -170,6 +170,8 @@ extern int mmc_erase_group_aligned(struct mmc_card *card, unsigned int from,
 extern unsigned int mmc_calc_max_discard(struct mmc_card *card);
 
 extern int mmc_set_blocklen(struct mmc_card *card, unsigned int blocklen);
+extern int mmc_set_blockcount(struct mmc_card *card, unsigned int blockcount,
+			      bool is_rel_write);
 extern int mmc_hw_reset(struct mmc_host *host);
 extern int mmc_hw_reset_check(struct mmc_host *host);
 extern int mmc_can_reset(struct mmc_card *card);

include/linux/mmc/dw_mmc.h

@@ -229,8 +229,9 @@ struct dw_mci_board {
 	u32 quirks; /* Workaround / Quirk flags */
 	unsigned int bus_hz; /* Clock speed at the cclk_in pad */
 
-	unsigned int caps;	/* Capabilities */
-	unsigned int caps2;	/* More capabilities */
+	u32 caps;	/* Capabilities */
+	u32 caps2;	/* More capabilities */
+	u32 pm_caps;	/* PM capabilities */
 	/*
 	 * Override fifo depth. If 0, autodetect it from the FIFOTH register,
 	 * but note that this may not be reliable after a bootloader has used

include/linux/mmc/host.h

@@ -53,12 +53,12 @@ struct mmc_ios {
 #define MMC_TIMING_LEGACY	0
 #define MMC_TIMING_MMC_HS	1
 #define MMC_TIMING_SD_HS	2
-#define MMC_TIMING_UHS_SDR12	MMC_TIMING_LEGACY
-#define MMC_TIMING_UHS_SDR25	MMC_TIMING_SD_HS
-#define MMC_TIMING_UHS_SDR50	3
-#define MMC_TIMING_UHS_SDR104	4
-#define MMC_TIMING_UHS_DDR50	5
-#define MMC_TIMING_MMC_HS200	6
+#define MMC_TIMING_UHS_SDR12	3
+#define MMC_TIMING_UHS_SDR25	4
+#define MMC_TIMING_UHS_SDR50	5
+#define MMC_TIMING_UHS_SDR104	6
+#define MMC_TIMING_UHS_DDR50	7
+#define MMC_TIMING_MMC_HS200	8
 
 #define MMC_SDR_MODE		0
 #define MMC_1_2V_DDR_MODE	1
@@ -136,6 +136,7 @@ struct mmc_host_ops {
 	void	(*enable_preset_value)(struct mmc_host *host, bool enable);
 	int	(*select_drive_strength)(unsigned int max_dtr, int host_drv, int card_drv);
 	void	(*hw_reset)(struct mmc_host *host);
+	void	(*card_event)(struct mmc_host *host);
 };
 
 struct mmc_card;
@@ -211,7 +212,7 @@ struct mmc_host {
 #define MMC_VDD_34_35		0x00400000	/* VDD voltage 3.4 ~ 3.5 */
 #define MMC_VDD_35_36		0x00800000	/* VDD voltage 3.5 ~ 3.6 */
 
-	unsigned long		caps;		/* Host capabilities */
+	u32			caps;		/* Host capabilities */
 
 #define MMC_CAP_4_BIT_DATA	(1 << 0)	/* Can the host do 4 bit transfers */
 #define MMC_CAP_MMC_HIGHSPEED	(1 << 1)	/* Can do MMC high-speed timing */
@@ -241,7 +242,7 @@ struct mmc_host {
 #define MMC_CAP_CMD23		(1 << 30)	/* CMD23 supported. */
 #define MMC_CAP_HW_RESET	(1 << 31)	/* Hardware reset */
 
-	unsigned int		caps2;		/* More host capabilities */
+	u32			caps2;		/* More host capabilities */
 
 #define MMC_CAP2_BOOTPART_NOACC	(1 << 0)	/* Boot partition no access */
 #define MMC_CAP2_CACHE_CTRL	(1 << 1)	/* Allow cache control */

include/linux/mmc/mmc.h

@@ -286,6 +286,7 @@ struct _mmc_csd {
 #define EXT_CSD_BKOPS_START		164	/* W */
 #define EXT_CSD_SANITIZE_START		165     /* W */
 #define EXT_CSD_WR_REL_PARAM		166	/* RO */
+#define EXT_CSD_RPMB_MULT		168	/* RO */
 #define EXT_CSD_BOOT_WP			173	/* R/W */
 #define EXT_CSD_ERASE_GROUP_DEF		175	/* R/W */
 #define EXT_CSD_PART_CONFIG		179	/* R/W */
@@ -339,6 +340,7 @@ struct _mmc_csd {
 
 #define EXT_CSD_PART_CONFIG_ACC_MASK	(0x7)
 #define EXT_CSD_PART_CONFIG_ACC_BOOT0	(0x1)
+#define EXT_CSD_PART_CONFIG_ACC_RPMB	(0x3)
 #define EXT_CSD_PART_CONFIG_ACC_GP0	(0x4)
 
 #define EXT_CSD_PART_SUPPORT_PART_EN	(0x1)

include/linux/mmc/mxs-mmc.h

-/*
- * Copyright 2011 Freescale Semiconductor, Inc. All Rights Reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __LINUX_MMC_MXS_MMC_H__
-#define __LINUX_MMC_MXS_MMC_H__
-
-struct mxs_mmc_platform_data {
-	int wp_gpio;	/* write protect pin */
-	unsigned int flags;
-#define SLOTF_4_BIT_CAPABLE	(1 << 0)
-#define SLOTF_8_BIT_CAPABLE	(1 << 1)
-};
-
-#endif /* __LINUX_MMC_MXS_MMC_H__ */

include/linux/mmc/sdhci.h

@@ -92,6 +92,8 @@ struct sdhci_host {
 
 #define SDHCI_QUIRK2_HOST_OFF_CARD_ON			(1<<0)
 #define SDHCI_QUIRK2_HOST_NO_CMD23			(1<<1)
+/* The system physically doesn't support 1.8v, even if the host does */
+#define SDHCI_QUIRK2_NO_1_8_V				(1<<2)
 
 	int irq;		/* Device IRQ */
 	void __iomem *ioaddr;	/* Mapped address */
@@ -158,8 +160,8 @@ struct sdhci_host {
 
 	struct timer_list timer;	/* Timer for timeouts */
 
-	unsigned int caps;	/* Alternative CAPABILITY_0 */
-	unsigned int caps1;	/* Alternative CAPABILITY_1 */
+	u32 caps;		/* Alternative CAPABILITY_0 */
+	u32 caps1;		/* Alternative CAPABILITY_1 */
 
 	unsigned int            ocr_avail_sdio;	/* OCR bit masks */
 	unsigned int            ocr_avail_sd;

include/linux/platform_data/pxa_sdhci.h

@@ -38,6 +38,7 @@
  * @max_speed: the maximum speed supported
  * @host_caps: Standard MMC host capabilities bit field.
  * @quirks: quirks of platfrom
+ * @quirks2: quirks2 of platfrom
  * @pm_caps: pm_caps of platfrom
  */
 struct sdhci_pxa_platdata {
@@ -48,9 +49,10 @@ struct sdhci_pxa_platdata {
 	unsigned int	ext_cd_gpio;
 	bool		ext_cd_gpio_invert;
 	unsigned int	max_speed;
-	unsigned int	host_caps;
-	unsigned int	host_caps2;
+	u32		host_caps;
+	u32		host_caps2;
 	unsigned int	quirks;
+	unsigned int	quirks2;
 	unsigned int	pm_caps;
 };