Merge remote-tracking branch 'lorenzo/pci/dwc' into next

* lorenzo/pci/dwc:
  PCI: exynos: Fix a potential init_clk_resources NULL pointer dereference
  PCI: iproc: Fix NULL pointer dereference for BCMA
  PCI: dra7xx: Iterate over INTx status bits
  PCI: dra7xx: Fix legacy INTD IRQ handling
  PCI: qcom: Account for const type of of_device_id.data
  PCI: dwc: artpec6: Fix return value check in artpec6_add_pcie_ep()
  PCI: exynos: Remove deprecated PHY initialization code
  PCI: dwc: artpec6: Add support for the ARTPEC-7 SoC
  bindings: PCI: artpec: Add support for the ARTPEC-7 SoC
  PCI: dwc: artpec6: Deassert the core before waiting for PHY
  PCI: dwc: Make cpu_addr_fixup take struct dw_pcie as argument
  PCI: dwc: artpec6: Add support for endpoint mode
  bindings: PCI: artpec: Add support for endpoint mode
  PCI: dwc: artpec6: Split artpec6_pcie_establish_link() into smaller functions
  PCI: dwc: artpec6: Use BIT and GENMASK macros
  PCI: dwc: artpec6: Remove unused defines
  PCI: dwc: dra7xx: Help compiler to remove unused code
  PCI: dwc: dra7xx: Assign pp->ops in dra7xx_add_pcie_port() rather than in probe
  PCI: dwc: dra7xx: Refactor Kconfig and Makefile handling for host/ep mode
  PCI: designware-ep: Add generic function for raising MSI irq
  PCI: designware-ep: Remove static keyword from dw_pcie_ep_reset_bar()
  PCI: designware-ep: Pre-allocate memory for MSI in dw_pcie_ep_init
  PCI: designware-ep: Read-only registers need DBI_RO_WR_EN to be writable
  PCI: designware-ep: dw_pcie_ep_set_msi() should only set MMC bits
  PCI: dwc: Use the DMA-API to get the MSI address
  pci: dwc: pci-dra7xx: Make shutdown handler static

Includes resolution to conflict between:

  4494738d ("PCI: endpoint: Add the function number as argument to EPC ops")
  6f6d7873 ("PCI: designware-ep: Add generic function for raising MSI irq")

The resolution is due to Niklas Cassel <niklas.cassel@axis.com>:
https://lkml.kernel.org/r/20180201085608.GA22568@axis.com

Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt

@@ -4,7 +4,10 @@ This PCIe host controller is based on the Synopsys DesignWare PCIe IP
 and thus inherits all the common properties defined in designware-pcie.txt.
 
 Required properties:
-- compatible: "axis,artpec6-pcie", "snps,dw-pcie"
+- compatible: "axis,artpec6-pcie", "snps,dw-pcie" for ARTPEC-6 in RC mode;
+	      "axis,artpec6-pcie-ep", "snps,dw-pcie" for ARTPEC-6 in EP mode;
+	      "axis,artpec7-pcie", "snps,dw-pcie" for ARTPEC-7 in RC mode;
+	      "axis,artpec7-pcie-ep", "snps,dw-pcie" for ARTPEC-7 in EP mode;
 - reg: base addresses and lengths of the PCIe controller (DBI),
 	the PHY controller, and configuration address space.
 - reg-names: Must include the following entries:

Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt

@@ -6,9 +6,6 @@ and thus inherits all the common properties defined in designware-pcie.txt.
 Required properties:
 - compatible: "samsung,exynos5440-pcie"
 - reg: base addresses and lengths of the PCIe controller,
-	the PHY controller, additional register for the PHY controller.
-	(Registers for the PHY controller are DEPRECATED.
-	 Use the PHY framework.)
 - reg-names : First name should be set to "elbi".
 	And use the "config" instead of getting the configuration address space
 	from "ranges".
@@ -23,49 +20,8 @@ For other common properties, refer to
 
 Example:
 
-SoC-specific DT Entry:
+SoC-specific DT Entry (with using PHY framework):
 
-	pcie@290000 {
-		compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
-		reg = <0x290000 0x1000
-			0x270000 0x1000
-			0x271000 0x40>;
-		interrupts = <0 20 0>, <0 21 0>, <0 22 0>;
-		clocks = <&clock 28>, <&clock 27>;
-		clock-names = "pcie", "pcie_bus";
-		#address-cells = <3>;
-		#size-cells = <2>;
-		device_type = "pci";
-		ranges = <0x00000800 0 0x40000000 0x40000000 0 0x00001000   /* configuration space */
-			  0x81000000 0 0	  0x40001000 0 0x00010000   /* downstream I/O */
-			  0x82000000 0 0x40011000 0x40011000 0 0x1ffef000>; /* non-prefetchable memory */
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
-		num-lanes = <4>;
-	};
-
-	pcie@2a0000 {
-		compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
-		reg = <0x2a0000 0x1000
-			0x272000 0x1000
-			0x271040 0x40>;
-		interrupts = <0 23 0>, <0 24 0>, <0 25 0>;
-		clocks = <&clock 29>, <&clock 27>;
-		clock-names = "pcie", "pcie_bus";
-		#address-cells = <3>;
-		#size-cells = <2>;
-		device_type = "pci";
-		ranges = <0x00000800 0 0x60000000 0x60000000 0 0x00001000   /* configuration space */
-			  0x81000000 0 0	  0x60001000 0 0x00010000   /* downstream I/O */
-			  0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>; /* non-prefetchable memory */
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
-		num-lanes = <4>;
-	};
-
-With using PHY framework:
 	pcie_phy0: pcie-phy@270000 {
 		...
 		reg = <0x270000 0x1000>, <0x271000 0x40>;
@@ -74,13 +30,21 @@ With using PHY framework:
 	};
 
 	pcie@290000 {
-		...
+		compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
 		reg = <0x290000 0x1000>, <0x40000000 0x1000>;
 		reg-names = "elbi", "config";
+		clocks = <&clock 28>, <&clock 27>;
+		clock-names = "pcie", "pcie_bus";
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
 		phys = <&pcie_phy0>;
 		ranges = <0x81000000 0 0	  0x60001000 0 0x00010000
 			  0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>;
-		...
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+		num-lanes = <4>;
 	};
 
 Board-specific DT Entry:

drivers/pci/dwc/Kconfig

@@ -15,39 +15,38 @@ config PCIE_DW_EP
 	select PCIE_DW
 
 config PCI_DRA7XX
-	bool "TI DRA7xx PCIe controller"
-	depends on SOC_DRA7XX || COMPILE_TEST
-	depends on (PCI && PCI_MSI_IRQ_DOMAIN) || PCI_ENDPOINT
-	depends on OF && HAS_IOMEM && TI_PIPE3
-	help
-	 Enables support for the PCIe controller in the DRA7xx SoC. There
-	 are two instances of PCIe controller in DRA7xx. This controller can
-	 work either as EP or RC. In order to enable host-specific features
-	 PCI_DRA7XX_HOST must be selected and in order to enable device-
-	 specific features PCI_DRA7XX_EP must be selected. This uses
-	 the DesignWare core.
-
-if PCI_DRA7XX
+	bool
 
 config PCI_DRA7XX_HOST
-	bool "PCI DRA7xx Host Mode"
-	depends on PCI
-	depends on PCI_MSI_IRQ_DOMAIN
+	bool "TI DRA7xx PCIe controller Host Mode"
+	depends on SOC_DRA7XX || COMPILE_TEST
+	depends on PCI && PCI_MSI_IRQ_DOMAIN
+	depends on OF && HAS_IOMEM && TI_PIPE3
 	select PCIE_DW_HOST
+	select PCI_DRA7XX
 	default y
 	help
 	  Enables support for the PCIe controller in the DRA7xx SoC to work in
-	 host mode.
+	  host mode. There are two instances of PCIe controller in DRA7xx.
+	  This controller can work either as EP or RC. In order to enable
+	  host-specific features PCI_DRA7XX_HOST must be selected and in order
+	  to enable device-specific features PCI_DRA7XX_EP must be selected.
+	  This uses the DesignWare core.
 
 config PCI_DRA7XX_EP
-	bool "PCI DRA7xx Endpoint Mode"
+	bool "TI DRA7xx PCIe controller Endpoint Mode"
+	depends on SOC_DRA7XX || COMPILE_TEST
 	depends on PCI_ENDPOINT
+	depends on OF && HAS_IOMEM && TI_PIPE3
 	select PCIE_DW_EP
+	select PCI_DRA7XX
 	help
 	  Enables support for the PCIe controller in the DRA7xx SoC to work in
-	 endpoint mode.
-
-endif
+	  endpoint mode. There are two instances of PCIe controller in DRA7xx.
+	  This controller can work either as EP or RC. In order to enable
+	  host-specific features PCI_DRA7XX_HOST must be selected and in order
+	  to enable device-specific features PCI_DRA7XX_EP must be selected.
+	  This uses the DesignWare core.
 
 config PCIE_DW_PLAT
 	bool "Platform bus based DesignWare PCIe Controller"
@@ -149,15 +148,28 @@ config PCIE_ARMADA_8K
 	  DesignWare core functions to implement the driver.
 
 config PCIE_ARTPEC6
-	bool "Axis ARTPEC-6 PCIe controller"
-	depends on PCI
+	bool
+
+config PCIE_ARTPEC6_HOST
+	bool "Axis ARTPEC-6 PCIe controller Host Mode"
 	depends on MACH_ARTPEC6
-	depends on PCI_MSI_IRQ_DOMAIN
+	depends on PCI && PCI_MSI_IRQ_DOMAIN
 	select PCIEPORTBUS
 	select PCIE_DW_HOST
+	select PCIE_ARTPEC6
+	help
+	  Enables support for the PCIe controller in the ARTPEC-6 SoC to work in
+	  host mode. This uses the DesignWare core.
+
+config PCIE_ARTPEC6_EP
+	bool "Axis ARTPEC-6 PCIe controller Endpoint Mode"
+	depends on MACH_ARTPEC6
+	depends on PCI_ENDPOINT
+	select PCIE_DW_EP
+	select PCIE_ARTPEC6
 	help
-	  Say Y here to enable PCIe controller support on Axis ARTPEC-6
-	  SoCs.  This PCIe controller uses the DesignWare core.
+	  Enables support for the PCIe controller in the ARTPEC-6 SoC to work in
+	  endpoint mode. This uses the DesignWare core.
 
 config PCIE_KIRIN
 	depends on OF && ARM64

drivers/pci/dwc/Makefile

@@ -3,9 +3,7 @@ obj-$(CONFIG_PCIE_DW) += pcie-designware.o
 obj-$(CONFIG_PCIE_DW_HOST) += pcie-designware-host.o
 obj-$(CONFIG_PCIE_DW_EP) += pcie-designware-ep.o
 obj-$(CONFIG_PCIE_DW_PLAT) += pcie-designware-plat.o
-ifneq ($(filter y,$(CONFIG_PCI_DRA7XX_HOST) $(CONFIG_PCI_DRA7XX_EP)),)
-        obj-$(CONFIG_PCI_DRA7XX) += pci-dra7xx.o
-endif
+obj-$(CONFIG_PCI_DRA7XX) += pci-dra7xx.o
 obj-$(CONFIG_PCI_EXYNOS) += pci-exynos.o
 obj-$(CONFIG_PCI_IMX6) += pci-imx6.o
 obj-$(CONFIG_PCIE_SPEAR13XX) += pcie-spear13xx.o

drivers/pci/dwc/pci-dra7xx.c

@@ -110,7 +110,7 @@ static inline void dra7xx_pcie_writel(struct dra7xx_pcie *pcie, u32 offset,
 	writel(value, pcie->base + offset);
 }
 
-static u64 dra7xx_pcie_cpu_addr_fixup(u64 pci_addr)
+static u64 dra7xx_pcie_cpu_addr_fixup(struct dw_pcie *pci, u64 pci_addr)
 {
 	return pci_addr & DRA7XX_CPU_TO_BUS_ADDR;
 }
@@ -226,6 +226,7 @@ static int dra7xx_pcie_intx_map(struct irq_domain *domain, unsigned int irq,
 
 static const struct irq_domain_ops intx_domain_ops = {
 	.map = dra7xx_pcie_intx_map,
+	.xlate = pci_irqd_intx_xlate,
 };
 
 static int dra7xx_pcie_init_irq_domain(struct pcie_port *pp)
@@ -256,7 +257,8 @@ static irqreturn_t dra7xx_pcie_msi_irq_handler(int irq, void *arg)
 	struct dra7xx_pcie *dra7xx = arg;
 	struct dw_pcie *pci = dra7xx->pci;
 	struct pcie_port *pp = &pci->pp;
-	u32 reg;
+	unsigned long reg;
+	u32 virq, bit;
 
 	reg = dra7xx_pcie_readl(dra7xx, PCIECTRL_DRA7XX_CONF_IRQSTATUS_MSI);
 
@@ -268,8 +270,11 @@ static irqreturn_t dra7xx_pcie_msi_irq_handler(int irq, void *arg)
 	case INTB:
 	case INTC:
 	case INTD:
-		generic_handle_irq(irq_find_mapping(dra7xx->irq_domain,
-						    ffs(reg)));
+		for_each_set_bit(bit, &reg, PCI_NUM_INTX) {
+			virq = irq_find_mapping(dra7xx->irq_domain, bit);
+			if (virq)
+				generic_handle_irq(virq);
+		}
 		break;
 	}
 
@@ -337,15 +342,6 @@ static irqreturn_t dra7xx_pcie_irq_handler(int irq, void *arg)
 	return IRQ_HANDLED;
 }
 
-static void dw_pcie_ep_reset_bar(struct dw_pcie *pci, enum pci_barno bar)
-{
-	u32 reg;
-
-	reg = PCI_BASE_ADDRESS_0 + (4 * bar);
-	dw_pcie_writel_dbi2(pci, reg, 0x0);
-	dw_pcie_writel_dbi(pci, reg, 0x0);
-}
-
 static void dra7xx_pcie_ep_init(struct dw_pcie_ep *ep)
 {
 	struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
@@ -375,7 +371,7 @@ static void dra7xx_pcie_raise_msi_irq(struct dra7xx_pcie *dra7xx,
 	dra7xx_pcie_writel(dra7xx, PCIECTRL_TI_CONF_MSI_XMT, reg);
 }
 
-static int dra7xx_pcie_raise_irq(struct dw_pcie_ep *ep,
+static int dra7xx_pcie_raise_irq(struct dw_pcie_ep *ep, u8 func_no,
 				 enum pci_epc_irq_type type, u8 interrupt_num)
 {
 	struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
@@ -470,6 +466,8 @@ static int __init dra7xx_add_pcie_port(struct dra7xx_pcie *dra7xx,
 	if (!pci->dbi_base)
 		return -ENOMEM;
 
+	pp->ops = &dra7xx_pcie_host_ops;
+
 	ret = dw_pcie_host_init(pp);
 	if (ret) {
 		dev_err(dev, "failed to initialize host\n");
@@ -599,7 +597,6 @@ static int __init dra7xx_pcie_probe(struct platform_device *pdev)
 	void __iomem *base;
 	struct resource *res;
 	struct dw_pcie *pci;
-	struct pcie_port *pp;
 	struct dra7xx_pcie *dra7xx;
 	struct device *dev = &pdev->dev;
 	struct device_node *np = dev->of_node;
@@ -627,9 +624,6 @@ static int __init dra7xx_pcie_probe(struct platform_device *pdev)
 	pci->dev = dev;
 	pci->ops = &dw_pcie_ops;
 
-	pp = &pci->pp;
-	pp->ops = &dra7xx_pcie_host_ops;
-
 	irq = platform_get_irq(pdev, 0);
 	if (irq < 0) {
 		dev_err(dev, "missing IRQ resource: %d\n", irq);
@@ -705,6 +699,11 @@ static int __init dra7xx_pcie_probe(struct platform_device *pdev)
 
 	switch (mode) {
 	case DW_PCIE_RC_TYPE:
+		if (!IS_ENABLED(CONFIG_PCI_DRA7XX_HOST)) {
+			ret = -ENODEV;
+			goto err_gpio;
+		}
+
 		dra7xx_pcie_writel(dra7xx, PCIECTRL_TI_CONF_DEVICE_TYPE,
 				   DEVICE_TYPE_RC);
 		ret = dra7xx_add_pcie_port(dra7xx, pdev);
@@ -712,6 +711,11 @@ static int __init dra7xx_pcie_probe(struct platform_device *pdev)
 			goto err_gpio;
 		break;
 	case DW_PCIE_EP_TYPE:
+		if (!IS_ENABLED(CONFIG_PCI_DRA7XX_EP)) {
+			ret = -ENODEV;
+			goto err_gpio;
+		}
+
 		dra7xx_pcie_writel(dra7xx, PCIECTRL_TI_CONF_DEVICE_TYPE,
 				   DEVICE_TYPE_EP);
 
@@ -810,7 +814,7 @@ static int dra7xx_pcie_resume_noirq(struct device *dev)
 }
 #endif
 
-void dra7xx_pcie_shutdown(struct platform_device *pdev)
+static void dra7xx_pcie_shutdown(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct dra7xx_pcie *dra7xx = dev_get_drvdata(dev);

drivers/pci/dwc/pcie-designware-ep.c

@@ -30,13 +30,15 @@ void dw_pcie_ep_linkup(struct dw_pcie_ep *ep)
 	pci_epc_linkup(epc);
 }
 
-static void dw_pcie_ep_reset_bar(struct dw_pcie *pci, enum pci_barno bar)
+void dw_pcie_ep_reset_bar(struct dw_pcie *pci, enum pci_barno bar)
 {
 	u32 reg;
 
 	reg = PCI_BASE_ADDRESS_0 + (4 * bar);
+	dw_pcie_dbi_ro_wr_en(pci);
 	dw_pcie_writel_dbi2(pci, reg, 0x0);
 	dw_pcie_writel_dbi(pci, reg, 0x0);
+	dw_pcie_dbi_ro_wr_dis(pci);
 }
 
 static int dw_pcie_ep_write_header(struct pci_epc *epc, u8 func_no,
@@ -45,6 +47,7 @@ static int dw_pcie_ep_write_header(struct pci_epc *epc, u8 func_no,
 	struct dw_pcie_ep *ep = epc_get_drvdata(epc);
 	struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
 
+	dw_pcie_dbi_ro_wr_en(pci);
 	dw_pcie_writew_dbi(pci, PCI_VENDOR_ID, hdr->vendorid);
 	dw_pcie_writew_dbi(pci, PCI_DEVICE_ID, hdr->deviceid);
 	dw_pcie_writeb_dbi(pci, PCI_REVISION_ID, hdr->revid);
@@ -58,6 +61,7 @@ static int dw_pcie_ep_write_header(struct pci_epc *epc, u8 func_no,
 	dw_pcie_writew_dbi(pci, PCI_SUBSYSTEM_ID, hdr->subsys_id);
 	dw_pcie_writeb_dbi(pci, PCI_INTERRUPT_PIN,
 			   hdr->interrupt_pin);
+	dw_pcie_dbi_ro_wr_dis(pci);
 
 	return 0;
 }
@@ -144,8 +148,10 @@ static int dw_pcie_ep_set_bar(struct pci_epc *epc, u8 func_no,
 	if (ret)
 		return ret;
 
+	dw_pcie_dbi_ro_wr_en(pci);
 	dw_pcie_writel_dbi2(pci, reg, size - 1);
 	dw_pcie_writel_dbi(pci, reg, flags);
+	dw_pcie_dbi_ro_wr_dis(pci);
 
 	return 0;
 }
@@ -224,8 +230,12 @@ static int dw_pcie_ep_set_msi(struct pci_epc *epc, u8 func_no, u8 encode_int)
 	struct dw_pcie_ep *ep = epc_get_drvdata(epc);
 	struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
 
-	val = (encode_int << MSI_CAP_MMC_SHIFT);
+	val = dw_pcie_readw_dbi(pci, MSI_MESSAGE_CONTROL);
+	val &= ~MSI_CAP_MMC_MASK;
+	val |= (encode_int << MSI_CAP_MMC_SHIFT) & MSI_CAP_MMC_MASK;
+	dw_pcie_dbi_ro_wr_en(pci);
 	dw_pcie_writew_dbi(pci, MSI_MESSAGE_CONTROL, val);
+	dw_pcie_dbi_ro_wr_dis(pci);
 
 	return 0;
 }
@@ -238,7 +248,7 @@ static int dw_pcie_ep_raise_irq(struct pci_epc *epc, u8 func_no,
 	if (!ep->ops->raise_irq)
 		return -EINVAL;
 
-	return ep->ops->raise_irq(ep, type, interrupt_num);
+	return ep->ops->raise_irq(ep, func_no, type, interrupt_num);
 }
 
 static void dw_pcie_ep_stop(struct pci_epc *epc)
@@ -276,10 +286,48 @@ static const struct pci_epc_ops epc_ops = {
 	.stop			= dw_pcie_ep_stop,
 };
 
+int dw_pcie_ep_raise_msi_irq(struct dw_pcie_ep *ep, u8 func_no,
+			     u8 interrupt_num)
+{
+	struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
+	struct pci_epc *epc = ep->epc;
+	u16 msg_ctrl, msg_data;
+	u32 msg_addr_lower, msg_addr_upper;
+	u64 msg_addr;
+	bool has_upper;
+	int ret;
+
+	/* Raise MSI per the PCI Local Bus Specification Revision 3.0, 6.8.1. */
+	msg_ctrl = dw_pcie_readw_dbi(pci, MSI_MESSAGE_CONTROL);
+	has_upper = !!(msg_ctrl & PCI_MSI_FLAGS_64BIT);
+	msg_addr_lower = dw_pcie_readl_dbi(pci, MSI_MESSAGE_ADDR_L32);
+	if (has_upper) {
+		msg_addr_upper = dw_pcie_readl_dbi(pci, MSI_MESSAGE_ADDR_U32);
+		msg_data = dw_pcie_readw_dbi(pci, MSI_MESSAGE_DATA_64);
+	} else {
+		msg_addr_upper = 0;
+		msg_data = dw_pcie_readw_dbi(pci, MSI_MESSAGE_DATA_32);
+	}
+	msg_addr = ((u64) msg_addr_upper) << 32 | msg_addr_lower;
+	ret = dw_pcie_ep_map_addr(epc, func_no, ep->msi_mem_phys, msg_addr,
+				  epc->mem->page_size);
+	if (ret)
+		return ret;
+
+	writel(msg_data | (interrupt_num - 1), ep->msi_mem);
+
+	dw_pcie_ep_unmap_addr(epc, func_no, ep->msi_mem_phys);
+
+	return 0;
+}
+
 void dw_pcie_ep_exit(struct dw_pcie_ep *ep)
 {
 	struct pci_epc *epc = ep->epc;
 
+	pci_epc_mem_free_addr(epc, ep->msi_mem_phys, ep->msi_mem,
+			      epc->mem->page_size);
+
 	pci_epc_mem_exit(epc);
 }
 
@@ -335,6 +383,13 @@ int dw_pcie_ep_init(struct dw_pcie_ep *ep)
 		return ret;
 	}
 
+	ep->msi_mem = pci_epc_mem_alloc_addr(epc, &ep->msi_mem_phys,
+					     epc->mem->page_size);
+	if (!ep->msi_mem) {
+		dev_err(dev, "Failed to reserve memory for MSI\n");
+		return -ENOMEM;
+	}
+
 	ep->epc = epc;
 	epc_set_drvdata(epc, ep);
 	dw_pcie_setup(pci);

drivers/pci/dwc/pcie-designware-host.c

@@ -83,10 +83,19 @@ irqreturn_t dw_handle_msi_irq(struct pcie_port *pp)
 
 void dw_pcie_msi_init(struct pcie_port *pp)
 {
+	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+	struct device *dev = pci->dev;
+	struct page *page;
 	u64 msi_target;
 
-	pp->msi_data = __get_free_pages(GFP_KERNEL, 0);
-	msi_target = virt_to_phys((void *)pp->msi_data);
+	page = alloc_page(GFP_KERNEL);
+	pp->msi_data = dma_map_page(dev, page, 0, PAGE_SIZE, DMA_FROM_DEVICE);
+	if (dma_mapping_error(dev, pp->msi_data)) {
+		dev_err(dev, "failed to map MSI data\n");
+		__free_page(page);
+		return;
+	}
+	msi_target = (u64)pp->msi_data;
 
 	/* program the msi_data */
 	dw_pcie_wr_own_conf(pp, PCIE_MSI_ADDR_LO, 4,
@@ -187,7 +196,7 @@ static void dw_msi_setup_msg(struct pcie_port *pp, unsigned int irq, u32 pos)
 	if (pp->ops->get_msi_addr)
 		msi_target = pp->ops->get_msi_addr(pp);
 	else
-		msi_target = virt_to_phys((void *)pp->msi_data);
+		msi_target = (u64)pp->msi_data;
 
 	msg.address_lo = (u32)(msi_target & 0xffffffff);
 	msg.address_hi = (u32)(msi_target >> 32 & 0xffffffff);

drivers/pci/dwc/pcie-designware.c

@@ -149,7 +149,7 @@ void dw_pcie_prog_outbound_atu(struct dw_pcie *pci, int index, int type,
 	u32 retries, val;
 
 	if (pci->ops->cpu_addr_fixup)
-		cpu_addr = pci->ops->cpu_addr_fixup(cpu_addr);
+		cpu_addr = pci->ops->cpu_addr_fixup(pci, cpu_addr);
 
 	if (pci->iatu_unroll_enabled) {
 		dw_pcie_prog_outbound_atu_unroll(pci, index, type, cpu_addr,

drivers/pci/dwc/pcie-designware.h

@@ -14,6 +14,7 @@
 #ifndef _PCIE_DESIGNWARE_H
 #define _PCIE_DESIGNWARE_H
 
+#include <linux/dma-mapping.h>
 #include <linux/irq.h>
 #include <linux/msi.h>
 #include <linux/pci.h>
@@ -100,10 +101,13 @@
 
 #define MSI_MESSAGE_CONTROL		0x52
 #define MSI_CAP_MMC_SHIFT		1
+#define MSI_CAP_MMC_MASK		(7 << MSI_CAP_MMC_SHIFT)
 #define MSI_CAP_MME_SHIFT		4
 #define MSI_CAP_MME_MASK		(7 << MSI_CAP_MME_SHIFT)
 #define MSI_MESSAGE_ADDR_L32		0x54
 #define MSI_MESSAGE_ADDR_U32		0x58
+#define MSI_MESSAGE_DATA_32		0x58
+#define MSI_MESSAGE_DATA_64		0x5C
 
 /*
  * Maximum number of MSI IRQs can be 256 per controller. But keep
@@ -168,7 +172,7 @@ struct pcie_port {
 	const struct dw_pcie_host_ops *ops;
 	int			msi_irq;
 	struct irq_domain	*irq_domain;
-	unsigned long		msi_data;
+	dma_addr_t		msi_data;
 	DECLARE_BITMAP(msi_irq_in_use, MAX_MSI_IRQS);
 };
 
@@ -180,8 +184,8 @@ enum dw_pcie_as_type {
 
 struct dw_pcie_ep_ops {
 	void	(*ep_init)(struct dw_pcie_ep *ep);
-	int	(*raise_irq)(struct dw_pcie_ep *ep, enum pci_epc_irq_type type,
-			     u8 interrupt_num);
+	int	(*raise_irq)(struct dw_pcie_ep *ep, u8 func_no,
+			     enum pci_epc_irq_type type, u8 interrupt_num);
 };
 
 struct dw_pcie_ep {
@@ -196,10 +200,12 @@ struct dw_pcie_ep {
 	unsigned long		ob_window_map;
 	u32			num_ib_windows;
 	u32			num_ob_windows;
+	void __iomem		*msi_mem;
+	phys_addr_t		msi_mem_phys;
 };
 
 struct dw_pcie_ops {
-	u64	(*cpu_addr_fixup)(u64 cpu_addr);
+	u64	(*cpu_addr_fixup)(struct dw_pcie *pcie, u64 cpu_addr);
 	u32	(*read_dbi)(struct dw_pcie *pcie, void __iomem *base, u32 reg,
 			    size_t size);
 	void	(*write_dbi)(struct dw_pcie *pcie, void __iomem *base, u32 reg,
@@ -334,6 +340,9 @@ static inline int dw_pcie_host_init(struct pcie_port *pp)
 void dw_pcie_ep_linkup(struct dw_pcie_ep *ep);
 int dw_pcie_ep_init(struct dw_pcie_ep *ep);
 void dw_pcie_ep_exit(struct dw_pcie_ep *ep);
+int dw_pcie_ep_raise_msi_irq(struct dw_pcie_ep *ep, u8 func_no,
+			     u8 interrupt_num);
+void dw_pcie_ep_reset_bar(struct dw_pcie *pci, enum pci_barno bar);
 #else
 static inline void dw_pcie_ep_linkup(struct dw_pcie_ep *ep)
 {
@@ -347,5 +356,15 @@ static inline int dw_pcie_ep_init(struct dw_pcie_ep *ep)
 static inline void dw_pcie_ep_exit(struct dw_pcie_ep *ep)
 {
 }
+
+static inline int dw_pcie_ep_raise_msi_irq(struct dw_pcie_ep *ep, u8 func_no,
+					   u8 interrupt_num)
+{
+	return 0;
+}
+
+static inline void dw_pcie_ep_reset_bar(struct dw_pcie *pci, enum pci_barno bar)
+{
+}
 #endif
 #endif /* _PCIE_DESIGNWARE_H */

drivers/pci/dwc/pcie-qcom.c

@@ -171,7 +171,7 @@ struct qcom_pcie {
 	union qcom_pcie_resources res;
 	struct phy *phy;
 	struct gpio_desc *reset;
-	struct qcom_pcie_ops *ops;
+	const struct qcom_pcie_ops *ops;
 };
 
 #define to_qcom_pcie(x)		dev_get_drvdata((x)->dev)
@@ -1234,7 +1234,7 @@ static int qcom_pcie_probe(struct platform_device *pdev)
 
 	pcie->pci = pci;
 
-	pcie->ops = (struct qcom_pcie_ops *)of_device_get_match_data(dev);
+	pcie->ops = of_device_get_match_data(dev);
 
 	pcie->reset = devm_gpiod_get_optional(dev, "perst", GPIOD_OUT_LOW);
 	if (IS_ERR(pcie->reset))

drivers/pci/host/pcie-iproc-platform.c

@@ -92,6 +92,13 @@ static int iproc_pcie_pltfm_probe(struct platform_device *pdev)
 		pcie->need_ob_cfg = true;
 	}
 
+	/*
+	 * DT nodes are not used by all platforms that use the iProc PCIe
+	 * core driver. For platforms that require explict inbound mapping
+	 * configuration, "dma-ranges" would have been present in DT
+	 */
+	pcie->need_ib_cfg = of_property_read_bool(np, "dma-ranges");
+
 	/* PHY use is optional */
 	pcie->phy = devm_phy_get(dev, "pcie-phy");
 	if (IS_ERR(pcie->phy)) {

drivers/pci/host/pcie-iproc.c

@@ -1378,9 +1378,11 @@ int iproc_pcie_setup(struct iproc_pcie *pcie, struct list_head *res)
 		}
 	}
 
+	if (pcie->need_ib_cfg) {
 		ret = iproc_pcie_map_dma_ranges(pcie);
 		if (ret && ret != -ENOENT)
 			goto err_power_off_phy;
+	}
 
 #ifdef CONFIG_ARM
 	pcie->sysdata.private_data = pcie;

drivers/pci/host/pcie-iproc.h

@@ -74,6 +74,7 @@ struct iproc_msi;
  * @ob: outbound mapping related parameters
  * @ob_map: outbound mapping related parameters specific to the controller
  *
+ * @need_ib_cfg: indicates SW needs to configure the inbound mapping window
  * @ib: inbound mapping related parameters
  * @ib_map: outbound mapping region related parameters
  *
@@ -101,6 +102,7 @@ struct iproc_pcie {
 	struct iproc_pcie_ob ob;
 	const struct iproc_pcie_ob_map *ob_map;
 
+	bool need_ib_cfg;
 	struct iproc_pcie_ib ib;
 	const struct iproc_pcie_ib_map *ib_map;