[PATCH] Char: isicom, remove isa code

ISA is not supported by this driver, remove parts, that take care of this.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

drivers/char/isicom.c

@@ -193,7 +193,6 @@ struct	isi_board {
 	unsigned short		shift_count;
 	struct isi_port		* ports;
 	signed char		count;
-	unsigned char		isa;
 	spinlock_t		card_lock; /* Card wide lock 11/5/00 -sameer */
 	unsigned long		flags;
 };
@@ -562,14 +561,12 @@ static irqreturn_t isicom_interrupt(int irq, void *dev_id)
 	base = card->base;
 	spin_lock(&card->card_lock);
 
-	if (card->isa == NO) {
 	/*
 	 * disable any interrupts from the PCI card and lower the
 	 * interrupt line
 	 */
 	outw(0x8000, base+0x04);
 	ClearInterrupt(base);
-	}
 
 	inw(base);		/* get the dummy word out */
 	header = inw(base);
@@ -579,18 +576,12 @@ static irqreturn_t isicom_interrupt(int irq, void *dev_id)
 	if (channel + 1 > card->port_count) {
 		printk(KERN_WARNING "ISICOM: isicom_interrupt(0x%lx): "
 			"%d(channel) > port_count.\n", base, channel+1);
-		if (card->isa)
-			ClearInterrupt(base);
-		else
 		outw(0x0000, base+0x04); /* enable interrupts */
 		spin_unlock(&card->card_lock);
 		return IRQ_HANDLED;
 	}
 	port = card->ports + channel;
 	if (!(port->flags & ASYNC_INITIALIZED)) {
-		if (card->isa)
-			ClearInterrupt(base);
-		else
 		outw(0x0000, base+0x04); /* enable interrupts */
 		return IRQ_HANDLED;
 	}
@@ -604,9 +595,6 @@ static irqreturn_t isicom_interrupt(int irq, void *dev_id)
 		}
 		if (byte_count & 0x01)
 			inw(base);
-		if (card->isa == YES)
-			ClearInterrupt(base);
-		else
 		outw(0x0000, base+0x04); /* enable interrupts */
 		spin_unlock(&card->card_lock);
 		return IRQ_HANDLED;
@@ -708,9 +696,6 @@ static irqreturn_t isicom_interrupt(int irq, void *dev_id)
 		}
 		tty_flip_buffer_push(tty);
 	}
-	if (card->isa == YES)
-		ClearInterrupt(base);
-	else
 	outw(0x0000, base+0x04); /* enable interrupts */
 
 	return IRQ_HANDLED;
@@ -1561,17 +1546,6 @@ static int __devinit reset_card(struct pci_dev *pdev,
 
 	*signature = inw(base + 0x4) & 0xff;
 
-	if (board->isa == YES) {
-		if (!(inw(base + 0xe) & 0x1) || (inw(base + 0x2))) {
-			dev_dbg(&pdev->dev, "base+0x2=0x%lx, base+0xe=0x%lx\n",
-				inw(base + 0x2), inw(base + 0xe));
-			dev_err(&pdev->dev, "ISILoad:ISA Card%d reset failure "
-				"(Possible bad I/O Port Address 0x%lx).\n",
-				card + 1, base);
-			retval = -EIO;
-			goto end;
-		}
-	} else {
 	portcount = inw(base + 0x2);
 	if (!(inw(base + 0xe) & 0x1) || ((portcount != 0) &&
 			(portcount != 4) && (portcount != 8))) {
@@ -1583,14 +1557,12 @@ static int __devinit reset_card(struct pci_dev *pdev,
 		retval = -EIO;
 		goto end;
 	}
-	}
 
 	switch (*signature) {
 	case 0xa5:
 	case 0xbb:
 	case 0xdd:
-		board->port_count = (board->isa == NO && portcount == 4) ? 4 :
-			8;
+		board->port_count = (portcount == 4) ? 4 : 8;
 		board->shift_count = 12;
 		break;
 	case 0xcc:
@@ -1784,8 +1756,6 @@ static int __devinit load_firmware(struct pci_dev *pdev,
 /*
  *	Insmod can set static symbols so keep these static
  */
-static int io[4];
-static int irq[4];
 static int card;
 
 static int __devinit isicom_probe(struct pci_dev *pdev,
@@ -1813,7 +1783,6 @@ static int __devinit isicom_probe(struct pci_dev *pdev,
 
 	board->base = ioaddr;
 	board->irq = pciirq;
-	board->isa = NO;
 	card++;
 
 	pci_set_drvdata(pdev, board);
@@ -1888,20 +1857,6 @@ static int __init isicom_init(void)
  		}
 		isi_card[idx].base = 0;
 		isi_card[idx].irq = 0;
-
-		if (!io[idx])
-			continue;
-
-		if (irq[idx] == 2 || irq[idx] == 3 || irq[idx] == 4	||
-				irq[idx] == 5	|| irq[idx] == 7	||
-				irq[idx] == 10	|| irq[idx] == 11	||
-				irq[idx] == 12	|| irq[idx] == 15) {
-			printk(KERN_ERR "ISICOM: ISA not supported yet.\n");
-			retval = -EINVAL;
-			goto error;
-		} else
-			printk(KERN_ERR "ISICOM: Irq %d unsupported. "
-				"Disabling Card%d...\n", irq[idx], idx + 1);
 	}
 
 	/* tty driver structure initialization */
@@ -1971,7 +1926,3 @@ module_exit(isicom_exit);
 MODULE_AUTHOR("MultiTech");
 MODULE_DESCRIPTION("Driver for the ISI series of cards by MultiTech");
 MODULE_LICENSE("GPL");
-module_param_array(io, int, NULL, 0);
-MODULE_PARM_DESC(io, "I/O ports for the cards");
-module_param_array(irq, int, NULL, 0);
-MODULE_PARM_DESC(irq, "Interrupts for the cards");