[PATCH] USB: sl811-hcd fixes

Various fixes to the sl811-hcd driver:

  * Fix small glitches that crept in during recent evolution of usbcore's hcd
    glue layer, coupling endpoint state records to usbcore and active urbs.
    (As noted by folk whose boards weren't stuck on 2.6.9 kernels...)

  * Cope with various system-specific issues:
      - Some configurations (e.g. a CF-card uses this chip) have iospace
        addresses for the two registers, rather than memory mapped ones.
      - Some configurations do interesting things with IRQs; maybe the
        line is shared, or it doesn't support level triggering.
      - Not all boards can drive the chip reset line in software.

  * Address a potential race during unlinking.

  * Tweak probe/remove section info to handle the case where this segment
    of a platform bus is hotpluggable (e.g. CF card).  (The basic problem
    is that CONFIG_HOTPLUG is global, which is wrong since not all busses
    can hotplug even on hotplug-friendly systems...)  Also export the
    driver, so that the CF driver can depend on it.

Also removed some annoying end-of-line whitespace.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drivers/usb/host/sl811-hcd.c

@@ -2,7 +2,7 @@
  * SL811HS HCD (Host Controller Driver) for USB.
  *
  * Copyright (C) 2004 Psion Teklogix (for NetBook PRO)
- * Copyright (C) 2004 David Brownell
+ * Copyright (C) 2004-2005 David Brownell
  *
  * Periodic scheduling is based on Roman's OHCI code
  * 	Copyright (C) 1999 Roman Weissgaerber
@@ -67,7 +67,7 @@
 MODULE_DESCRIPTION("SL811HS USB Host Controller Driver");
 MODULE_LICENSE("GPL");
 
-#define DRIVER_VERSION	"15 Dec 2004"
+#define DRIVER_VERSION	"19 May 2005"
 
 
 #ifndef DEBUG
@@ -121,6 +121,10 @@ static void port_power(struct sl811 *sl811, int is_on)
 	/* reset as thoroughly as we can */
 	if (sl811->board && sl811->board->reset)
 		sl811->board->reset(hcd->self.controller);
+	else {
+		sl811_write(sl811, SL11H_CTLREG1, SL11H_CTL1MASK_SE0);
+		mdelay(20);
+	}
 
 	sl811_write(sl811, SL11H_IRQ_ENABLE, 0);
 	sl811_write(sl811, SL11H_CTLREG1, sl811->ctrl1);
@@ -443,6 +447,7 @@ static void finish_request(
 	spin_lock(&urb->lock);
 	if (urb->status == -EINPROGRESS)
 		urb->status = status;
+	urb->hcpriv = NULL;
 	spin_unlock(&urb->lock);
 
 	spin_unlock(&sl811->lock);
@@ -661,9 +666,9 @@ static irqreturn_t sl811h_irq(struct usb_hcd *hcd, struct pt_regs *regs)
 
 #ifdef	QUIRK2
 	/* this may no longer be necessary ... */
-	if (irqstat == 0 && ret == IRQ_NONE) {
+	if (irqstat == 0) {
 		irqstat = checkdone(sl811);
-		if (irqstat /* && irq != ~0 */ )
+		if (irqstat)
 			sl811->stat_lost++;
 	}
 #endif
@@ -722,7 +727,8 @@ static irqreturn_t sl811h_irq(struct usb_hcd *hcd, struct pt_regs *regs)
 		if (sl811->active_a) {
 			sl811_write(sl811, SL811_EP_A(SL11H_HOSTCTLREG), 0);
 			finish_request(sl811, sl811->active_a,
-				container_of(sl811->active_a->hep->urb_list.next,
+				container_of(sl811->active_a
+						->hep->urb_list.next,
 					struct urb, urb_list),
 				NULL, -ESHUTDOWN);
 			sl811->active_a = NULL;
@@ -731,7 +737,8 @@ static irqreturn_t sl811h_irq(struct usb_hcd *hcd, struct pt_regs *regs)
 		if (sl811->active_b) {
 			sl811_write(sl811, SL811_EP_B(SL11H_HOSTCTLREG), 0);
 			finish_request(sl811, sl811->active_b,
-				container_of(sl811->active_b->hep->urb_list.next,
+				container_of(sl811->active_b
+						->hep->urb_list.next,
 					struct urb, urb_list),
 				NULL, -ESHUTDOWN);
 			sl811->active_b = NULL;
@@ -890,6 +897,7 @@ static int sl811h_urb_enqueue(
 			break;
 		}
 
+		ep->hep = hep;
 		hep->hcpriv = ep;
 	}
 
@@ -961,15 +969,16 @@ static int sl811h_urb_enqueue(
 static int sl811h_urb_dequeue(struct usb_hcd *hcd, struct urb *urb)
 {
 	struct sl811		*sl811 = hcd_to_sl811(hcd);
-	struct usb_host_endpoint *hep = urb->hcpriv;
+	struct usb_host_endpoint *hep;
 	unsigned long		flags;
 	struct sl811h_ep	*ep;
 	int			retval = 0;
 
+	spin_lock_irqsave(&sl811->lock, flags);
+	hep = urb->hcpriv;
 	if (!hep)
-		return -EINVAL;
+		goto fail;
 
-	spin_lock_irqsave(&sl811->lock, flags);
 	ep = hep->hcpriv;
 	if (ep) {
 		/* finish right away if this urb can't be active ...
@@ -1017,6 +1026,7 @@ static int sl811h_urb_dequeue(struct usb_hcd *hcd, struct urb *urb)
 			VDBG("dequeue, urb %p active %s; wait4irq\n", urb,
 				(sl811->active_a == ep) ? "A" : "B");
 	} else
+fail:
 		retval = -EINVAL;
 	spin_unlock_irqrestore(&sl811->lock, flags);
 	return retval;
@@ -1576,6 +1586,9 @@ sl811h_start(struct usb_hcd *hcd)
 	if (sl811->board && sl811->board->power)
 		hub_set_power_budget(udev, sl811->board->power * 2);
 
+	/* enable power and interupts */
+	port_power(sl811, 1);
+
 	return 0;
 }
 
@@ -1618,7 +1631,7 @@ static struct hc_driver sl811h_hc_driver = {
 
 /*-------------------------------------------------------------------------*/
 
-static int __init_or_module
+static int __devexit
 sl811h_remove(struct device *dev)
 {
 	struct usb_hcd		*hcd = dev_get_drvdata(dev);
@@ -1631,21 +1644,20 @@ sl811h_remove(struct device *dev)
 	remove_debug_file(sl811);
 	usb_remove_hcd(hcd);
 
-	iounmap(sl811->data_reg);
+	/* some platforms may use IORESOURCE_IO */
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
-	release_mem_region(res->start, 1);
+	if (res)
+		iounmap(sl811->data_reg);
 
-	iounmap(sl811->addr_reg);
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	release_mem_region(res->start, 1);
+	if (res)
+		iounmap(sl811->addr_reg);
 
 	usb_put_hcd(hcd);
 	return 0;
 }
 
-#define resource_len(r) (((r)->end - (r)->start) + 1)
-
-static int __init
+static int __devinit
 sl811h_probe(struct device *dev)
 {
 	struct usb_hcd		*hcd;
@@ -1656,7 +1668,7 @@ sl811h_probe(struct device *dev)
 	void __iomem		*addr_reg;
 	void __iomem		*data_reg;
 	int			retval;
-	u8			tmp;
+	u8			tmp, ioaddr = 0;
 
 	/* basic sanity checks first.  board-specific init logic should
 	 * have initialized these three resources and probably board
@@ -1664,13 +1676,8 @@ sl811h_probe(struct device *dev)
 	 * minimal sanity checking.
 	 */
 	pdev = container_of(dev, struct platform_device, dev);
-	if (pdev->num_resources < 3)
-		return -ENODEV;
-
-	addr = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	data = platform_get_resource(pdev, IORESOURCE_MEM, 1);
 	irq = platform_get_irq(pdev, 0);
-	if (!addr || !data || irq < 0)
+	if (pdev->num_resources < 3 || irq < 0)
 		return -ENODEV;
 
 	/* refuse to confuse usbcore */
@@ -1679,25 +1686,32 @@ sl811h_probe(struct device *dev)
 		return -EINVAL;
 	}
 
-	if (!request_mem_region(addr->start, 1, hcd_name)) {
+	/* the chip may be wired for either kind of addressing */
+	addr = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	data = platform_get_resource(pdev, IORESOURCE_MEM, 1);
 	retval = -EBUSY;
-		goto err1;
-	}
-	addr_reg = ioremap(addr->start, resource_len(addr));
+	if (!addr || !data) {
+		addr = platform_get_resource(pdev, IORESOURCE_IO, 0);
+		data = platform_get_resource(pdev, IORESOURCE_IO, 1);
+		if (!addr || !data)
+			return -ENODEV;
+		ioaddr = 1;
+
+		addr_reg = (void __iomem *) addr->start;
+		data_reg = (void __iomem *) data->start;
+	} else {
+		addr_reg = ioremap(addr->start, 1);
 		if (addr_reg == NULL) {
 			retval = -ENOMEM;
 			goto err2;
 		}
 
-	if (!request_mem_region(data->start, 1, hcd_name)) {
-		retval = -EBUSY;
-		goto err3;
-	}
-	data_reg = ioremap(data->start, resource_len(addr));
+		data_reg = ioremap(data->start, 1);
 		if (data_reg == NULL) {
 			retval = -ENOMEM;
 			goto err4;
 		}
+	}
 
 	/* allocate and initialize hcd */
 	hcd = usb_create_hcd(&sl811h_hc_driver, dev, dev->bus_id);
@@ -1737,12 +1751,14 @@ sl811h_probe(struct device *dev)
 		goto err6;
 	}
 
-	/* sl811s would need a different handler for this irq */
-#ifdef	CONFIG_ARM
-	/* Cypress docs say the IRQ is IRQT_HIGH ... */
-	set_irq_type(irq, IRQT_RISING);
-#endif
-	retval = usb_add_hcd(hcd, irq, SA_INTERRUPT);
+	/* The chip's IRQ is level triggered, active high.  A requirement
+	 * for platform device setup is to cope with things like signal
+	 * inverters (e.g. CF is active low) or working only with edge
+	 * triggers (e.g. most ARM CPUs).  Initial driver stress testing
+	 * was on a system with single edge triggering, so most sorts of
+	 * triggering arrangement should work.
+	 */
+	retval = usb_add_hcd(hcd, irq, SA_INTERRUPT | SA_SHIRQ);
 	if (retval != 0)
 		goto err6;
 
@@ -1752,14 +1768,12 @@ sl811h_probe(struct device *dev)
  err6:
 	usb_put_hcd(hcd);
  err5:
+	if (!ioaddr)
 		iounmap(data_reg);
  err4:
-	release_mem_region(data->start, 1);
- err3:
+	if (!ioaddr)
 		iounmap(addr_reg);
  err2:
-	release_mem_region(addr->start, 1);
- err1:
 	DBG("init error, %d\n", retval);
 	return retval;
 }
@@ -1821,16 +1835,18 @@ sl811h_resume(struct device *dev, u32 phase)
 #endif
 
 
-static struct device_driver sl811h_driver = {
+/* this driver is exported so sl811_cs can depend on it */
+struct device_driver sl811h_driver = {
 	.name =		(char *) hcd_name,
 	.bus =		&platform_bus_type,
 
 	.probe =	sl811h_probe,
-	.remove =	sl811h_remove,
+	.remove =	__devexit_p(sl811h_remove),
 
 	.suspend =	sl811h_suspend,
 	.resume =	sl811h_resume,
 };
+EXPORT_SYMBOL(sl811h_driver);
 
 /*-------------------------------------------------------------------------*/