Merge branch 'next/dt-samsung' of...

Merge branch 'next/dt-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt

From Kukjin Kim:

Here is Samsung DT for v3.8 and this is including DT for EXYNOS4X12
SoC, SMDK4412 board, pinctrl for exynos4x12, TMU, MFC, SATA and SATA
PHY.

As I commented on [4/7], this branch merged pinctrl/samsung to support
pinctrl for exynos4x12 without useless merge conflicts.

* 'next/dt-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (32 commits)
  ARM: EXYNOS: DT Support for SATA and SATA PHY
  ARM: dts: Remove broken-voltage property from sdhci node for exynos4210-trats
  ARM: dts: Add node for touchscreen for exynos4210-trats
  ARM: dts: Add node for touchscreen voltage regulator for exynos4210-trats
  ARM: dts: Add node for i2c3 bus for exynos4210-trats
  ARM: dts: Add nodes for GPIO keys available on Trats
  ARM: dts: Update for pinctrl-samsung driver for exynos4210-trats
  ARM: dts: Add nodes for pin controllers for exynos4x12
  pinctrl: samsung: Add support for EXYNOS4X12
  gpio: samsung: Skip registration if pinctrl driver is present on EXYNOS4X12
  ARM: EXYNOS: Skip wakeup-int setup if pinctrl driver is used on EXYNOS4X12
  ARM: dts: add board dts file for EXYNOS4412 based SMDK board
  ARM: dts: Add support for EXYNOS4X12 SoCs
  ARM: EXYNOS: Add devicetree node for TMU driver for exynos5
  ARM: EXYNOS: Add devicetree node for TMU driver for exynos4
  ARM: EXYNOS: Add MFC device tree support
  ARM: dts: Enable serial controllers on Origen and SMDKV310
  Documentation: Update samsung-pinctrl device tree bindings documentation
  pinctrl: samsung: Add GPIO to IRQ translation
  pinctrl: exynos: Set pin function to EINT in irq_set_type of wake-up EINT
  ...

Add/add conflicts in:
	arch/arm/boot/dts/exynos5250-smdk5250.dts
	arch/arm/boot/dts/exynos5250.dtsi
	arch/arm/mach-exynos/mach-exynos5-dt.c
Signed-off-by: Olof Johansson <olof@lixom.net>

Documentation/devicetree/bindings/ata/exynos-sata-phy.txt

+* Samsung SATA PHY Controller
+
+SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers.
+Each SATA PHY controller should have its own node.
+
+Required properties:
+- compatible        : compatible list, contains "samsung,exynos5-sata-phy"
+- reg               : <registers mapping>
+
+Example:
+        sata@ffe07000 {
+                compatible = "samsung,exynos5-sata-phy";
+                reg = <0xffe07000 0x1000>;
+        };

Documentation/devicetree/bindings/ata/exynos-sata.txt

+* Samsung AHCI SATA Controller
+
+SATA nodes are defined to describe on-chip Serial ATA controllers.
+Each SATA controller should have its own node.
+
+Required properties:
+- compatible        : compatible list, contains "samsung,exynos5-sata"
+- interrupts        : <interrupt mapping for SATA IRQ>
+- reg               : <registers mapping>
+- samsung,sata-freq : <frequency in MHz>
+
+Example:
+        sata@ffe08000 {
+                compatible = "samsung,exynos5-sata";
+                reg = <0xffe08000 0x1000>;
+                interrupts = <115>;
+        };

Documentation/devicetree/bindings/media/s5p-mfc.txt

+* Samsung Multi Format Codec (MFC)
+
+Multi Format Codec (MFC) is the IP present in Samsung SoCs which
+supports high resolution decoding and encoding functionalities.
+The MFC device driver is a v4l2 driver which can encode/decode
+video raw/elementary streams and has support for all popular
+video codecs.
+
+Required properties:
+  - compatible : value should be either one among the following
+	(a) "samsung,mfc-v5" for MFC v5 present in Exynos4 SoCs
+	(b) "samsung,mfc-v6" for MFC v6 present in Exynos5 SoCs
+
+  - reg : Physical base address of the IP registers and length of memory
+	  mapped region.
+
+  - interrupts : MFC interrupt number to the CPU.
+
+  - samsung,mfc-r : Base address of the first memory bank used by MFC
+		    for DMA contiguous memory allocation and its size.
+
+  - samsung,mfc-l : Base address of the second memory bank used by MFC
+		    for DMA contiguous memory allocation and its size.

Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt

@@ -8,13 +8,20 @@ on-chip controllers onto these pads.
 Required Properties:
 - compatible: should be one of the following.
   - "samsung,pinctrl-exynos4210": for Exynos4210 compatible pin-controller.
+  - "samsung,pinctrl-exynos4x12": for Exynos4x12 compatible pin-controller.
   - "samsung,pinctrl-exynos5250": for Exynos5250 compatible pin-controller.
 
 - reg: Base address of the pin controller hardware module and length of
   the address space it occupies.
 
-- interrupts: interrupt specifier for the controller. The format and value of
-  the interrupt specifier depends on the interrupt parent for the controller.
+- Pin banks as child nodes: Pin banks of the controller are represented by child
+  nodes of the controller node. Bank name is taken from name of the node. Each
+  bank node must contain following properties:
+
+  - gpio-controller: identifies the node as a gpio controller and pin bank.
+  - #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO
+    binding is used, the amount of cells must be specified as 2. See generic
+    GPIO binding documentation for description of particular cells.
 
 - Pin mux/config groups as child nodes: The pin mux (selecting pin function
   mode) and pin config (pull up/down, driver strength) settings are represented
@@ -72,16 +79,24 @@ used as system wakeup events.
 A. External GPIO Interrupts: For supporting external gpio interrupts, the
    following properties should be specified in the pin-controller device node.
 
-- interrupt-controller: identifies the controller node as interrupt-parent.
-- #interrupt-cells: the value of this property should be 2.
-  - First Cell: represents the external gpio interrupt number local to the
-    external gpio interrupt space of the controller.
-  - Second Cell: flags to identify the type of the interrupt
-    - 1 = rising edge triggered
-    - 2 = falling edge triggered
-    - 3 = rising and falling edge triggered
-    - 4 = high level triggered
-    - 8 = low level triggered
+   - interrupt-parent: phandle of the interrupt parent to which the external
+     GPIO interrupts are forwarded to.
+   - interrupts: interrupt specifier for the controller. The format and value of
+     the interrupt specifier depends on the interrupt parent for the controller.
+
+   In addition, following properties must be present in node of every bank
+   of pins supporting GPIO interrupts:
+
+   - interrupt-controller: identifies the controller node as interrupt-parent.
+   - #interrupt-cells: the value of this property should be 2.
+     - First Cell: represents the external gpio interrupt number local to the
+       external gpio interrupt space of the controller.
+     - Second Cell: flags to identify the type of the interrupt
+       - 1 = rising edge triggered
+       - 2 = falling edge triggered
+       - 3 = rising and falling edge triggered
+       - 4 = high level triggered
+       - 8 = low level triggered
 
 B. External Wakeup Interrupts: For supporting external wakeup interrupts, a
    child node representing the external wakeup interrupt controller should be
@@ -94,6 +109,11 @@ B. External Wakeup Interrupts: For supporting external wakeup interrupts, a
        found on Samsung Exynos4210 SoC.
    - interrupt-parent: phandle of the interrupt parent to which the external
      wakeup interrupts are forwarded to.
+   - interrupts: interrupt used by multiplexed wakeup interrupts.
+
+   In addition, following properties must be present in node of every bank
+   of pins supporting wake-up interrupts:
+
    - interrupt-controller: identifies the node as interrupt-parent.
    - #interrupt-cells: the value of this property should be 2
      - First Cell: represents the external wakeup interrupt number local to
@@ -105,11 +125,63 @@ B. External Wakeup Interrupts: For supporting external wakeup interrupts, a
        - 4 = high level triggered
        - 8 = low level triggered
 
+   Node of every bank of pins supporting direct wake-up interrupts (without
+   multiplexing) must contain following properties:
+
+   - interrupt-parent: phandle of the interrupt parent to which the external
+     wakeup interrupts are forwarded to.
+   - interrupts: interrupts of the interrupt parent which are used for external
+     wakeup interrupts from pins of the bank, must contain interrupts for all
+     pins of the bank.
+
 Aliases:
 
 All the pin controller nodes should be represented in the aliases node using
 the following format 'pinctrl{n}' where n is a unique number for the alias.
 
+Example: A pin-controller node with pin banks:
+
+	pinctrl_0: pinctrl@11400000 {
+		compatible = "samsung,pinctrl-exynos4210";
+		reg = <0x11400000 0x1000>;
+		interrupts = <0 47 0>;
+
+		/* ... */
+
+		/* Pin bank without external interrupts */
+		gpy0: gpy0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		/* ... */
+
+		/* Pin bank with external GPIO or muxed wake-up interrupts */
+		gpj0: gpj0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		/* ... */
+
+		/* Pin bank with external direct wake-up interrupts */
+		gpx0: gpx0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			interrupt-parent = <&gic>;
+			interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
+				     <0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>;
+			#interrupt-cells = <2>;
+		};
+
+		/* ... */
+	};
+
 Example 1: A pin-controller node with pin groups.
 
 	pinctrl_0: pinctrl@11400000 {
@@ -117,6 +189,8 @@ Example 1: A pin-controller node with pin groups.
 		reg = <0x11400000 0x1000>;
 		interrupts = <0 47 0>;
 
+		/* ... */
+
 		uart0_data: uart0-data {
 			samsung,pins = "gpa0-0", "gpa0-1";
 			samsung,pin-function = <2>;
@@ -158,20 +232,14 @@ Example 2: A pin-controller node with external wakeup interrupt controller node.
 	pinctrl_1: pinctrl@11000000 {
 		compatible = "samsung,pinctrl-exynos4210";
 		reg = <0x11000000 0x1000>;
-		interrupts = <0 46 0>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
+		interrupts = <0 46 0>
 
-		wakup_eint: wakeup-interrupt-controller {
+		/* ... */
+
+		wakeup-interrupt-controller {
 			compatible = "samsung,exynos4210-wakeup-eint";
 			interrupt-parent = <&gic>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-			interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
-					<0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>,
-					<0 24 0>, <0 25 0>, <0 26 0>, <0 27 0>,
-					<0 28 0>, <0 29 0>, <0 30 0>, <0 31 0>,
-					<0 32 0>;
+			interrupts = <0 32 0>;
 		};
 	};
 
@@ -190,7 +258,8 @@ Example 4: Set up the default pin state for uart controller.
 
 	static int s3c24xx_serial_probe(struct platform_device *pdev) {
 		struct pinctrl *pinctrl;
-		...
-		...
+
+		/* ... */
+
 		pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
 	}

arch/arm/boot/dts/Makefile

@@ -25,6 +25,7 @@ dtb-$(CONFIG_ARCH_DOVE) += dove-cm-a510.dtb \
 dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
 	exynos4210-smdkv310.dtb \
 	exynos4210-trats.dtb \
+	exynos4412-smdk4412.dtb \
 	exynos5250-smdk5250.dtb
 dtb-$(CONFIG_ARCH_HIGHBANK) += highbank.dtb
 dtb-$(CONFIG_ARCH_INTEGRATOR) += integratorap.dtb \

arch/arm/boot/dts/exynos4210-origen.dts

@@ -57,6 +57,22 @@ sdhci@12510000 {
 		status = "okay";
 	};
 
+	serial@13800000 {
+		status = "okay";
+	};
+
+	serial@13810000 {
+		status = "okay";
+	};
+
+	serial@13820000 {
+		status = "okay";
+	};
+
+	serial@13830000 {
+		status = "okay";
+	};
+
 	gpio_keys {
 		compatible = "gpio-keys";
 		#address-cells = <1>;

arch/arm/boot/dts/exynos4210-pinctrl.dtsi

@@ -16,6 +16,134 @@
 
 / {
 	pinctrl@11400000 {
+		gpa0: gpa0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpa1: gpa1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpb: gpb {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpc0: gpc0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpc1: gpc1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpd0: gpd0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpd1: gpd1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpe0: gpe0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpe1: gpe1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpe2: gpe2 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpe3: gpe3 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpe4: gpe4 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpf0: gpf0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpf1: gpf1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpf2: gpf2 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpf3: gpf3 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
 		uart0_data: uart0-data {
 			samsung,pins = "gpa0-0", "gpa0-1";
 			samsung,pin-function = <0x2>;
@@ -205,6 +333,151 @@ i2c1_bus: i2c1-bus {
 	};
 
 	pinctrl@11000000 {
+		gpj0: gpj0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpj1: gpj1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpk0: gpk0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpk1: gpk1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpk2: gpk2 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpk3: gpk3 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpl0: gpl0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpl1: gpl1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpl2: gpl2 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpy0: gpy0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpy1: gpy1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpy2: gpy2 {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpy3: gpy3 {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpy4: gpy4 {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpy5: gpy5 {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpy6: gpy6 {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpx0: gpx0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			interrupt-parent = <&gic>;
+			interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
+				     <0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>;
+			#interrupt-cells = <2>;
+		};
+
+		gpx1: gpx1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			interrupt-parent = <&gic>;
+			interrupts = <0 24 0>, <0 25 0>, <0 26 0>, <0 27 0>,
+				     <0 28 0>, <0 29 0>, <0 30 0>, <0 31 0>;
+			#interrupt-cells = <2>;
+		};
+
+		gpx2: gpx2 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpx3: gpx3 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
 		sd0_clk: sd0-clk {
 			samsung,pins = "gpk0-0";
 			samsung,pin-function = <2>;
@@ -438,6 +711,11 @@ eint31: ext-int31 {
 	};
 
 	pinctrl@03860000 {
+		gpz: gpz {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
 		i2s0_bus: i2s0-bus {
 			samsung,pins = "gpz-0", "gpz-1", "gpz-2", "gpz-3",
 					"gpz-4", "gpz-5", "gpz-6";

arch/arm/boot/dts/exynos4210-smdkv310.dts

@@ -43,6 +43,22 @@ sdhci@12530000 {
 		status = "okay";
 	};
 
+	serial@13800000 {
+		status = "okay";
+	};
+
+	serial@13810000 {
+		status = "okay";
+	};
+
+	serial@13820000 {
+		status = "okay";
+	};
+
+	serial@13830000 {
+		status = "okay";
+	};
+
 	keypad@100A0000 {
 		samsung,keypad-num-rows = <2>;
 		samsung,keypad-num-columns = <8>;

arch/arm/boot/dts/exynos4210-trats.dts

@@ -35,24 +35,15 @@ vemmc_reg: voltage-regulator@0 {
 		regulator-name = "VMEM_VDD_2.8V";
 		regulator-min-microvolt = <2800000>;
 		regulator-max-microvolt = <2800000>;
-		gpio = <&gpk0 2 1 0 0>;
+		gpio = <&gpk0 2 0>;
 		enable-active-high;
 	};
 
 	sdhci_emmc: sdhci@12510000 {
 		bus-width = <8>;
 		non-removable;
-		broken-voltage;
-		gpios = <&gpk0 0 2 0 3>,
-			<&gpk0 1 2 0 3>,
-			<&gpk0 3 2 2 3>,
-			<&gpk0 4 2 2 3>,
-			<&gpk0 5 2 2 3>,
-			<&gpk0 6 2 2 3>,
-			<&gpk1 3 3 3 3>,
-			<&gpk1 4 3 3 3>,
-			<&gpk1 5 3 3 3>,
-			<&gpk1 6 3 3 3>;
+		pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus8>;
+		pinctrl-names = "default";
 		vmmc-supply = <&vemmc_reg>;
 		status = "okay";
 	};
@@ -73,12 +64,74 @@ serial@13830000 {
 		status = "okay";
 	};
 
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		vol-down-key {
+			gpios = <&gpx2 1 1>;
+			linux,code = <114>;
+			label = "volume down";
+			debounce-interval = <10>;
+		};
+
+		vol-up-key {
+			gpios = <&gpx2 0 1>;
+			linux,code = <115>;
+			label = "volume up";
+			debounce-interval = <10>;
+		};
+
+		power-key {
+			gpios = <&gpx2 7 1>;
+			linux,code = <116>;
+			label = "power";
+			debounce-interval = <10>;
+			gpio-key,wakeup;
+		};
+
+		ok-key {
+			gpios = <&gpx3 5 1>;
+			linux,code = <352>;
+			label = "ok";
+			debounce-interval = <10>;
+		};
+	};
+
+	tsp_reg: voltage-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "TSP_FIXED_VOLTAGES";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&gpl0 3 0>;
+		enable-active-high;
+	};
+
+	i2c@13890000 {
+		samsung,i2c-sda-delay = <100>;
+		samsung,i2c-slave-addr = <0x10>;
+		samsung,i2c-max-bus-freq = <400000>;
+		pinctrl-0 = <&i2c3_bus>;
+		pinctrl-names = "default";
+		status = "okay";
+
+		mms114-touchscreen@48 {
+			compatible = "melfas,mms114";
+			reg = <0x48>;
+			interrupt-parent = <&gpx0>;
+			interrupts = <4 2>;
+			x-size = <720>;
+			y-size = <1280>;
+			avdd-supply = <&tsp_reg>;
+			vdd-supply = <&tsp_reg>;
+		};
+	};
+
 	i2c@138B0000 {
 		samsung,i2c-sda-delay = <100>;
 		samsung,i2c-slave-addr = <0x10>;
 		samsung,i2c-max-bus-freq = <100000>;
-		gpios = <&gpb 6 3 3 0>,
-			<&gpb 7 3 3 0>;
+		pinctrl-0 = <&i2c5_bus>;
+		pinctrl-names = "default";
 		status = "okay";
 
 		max8997_pmic@66 {
@@ -93,9 +146,9 @@ max8997_pmic@66 {
 			max8997,pmic-ignore-gpiodvs-side-effect;
 			max8997,pmic-buck125-default-dvs-idx = <0>;
 
-			max8997,pmic-buck125-dvs-gpios = <&gpx0 5 1 0 0>,
-						         <&gpx0 6 1 0 0>,
-							 <&gpl0 0 1 0 0>;
+			max8997,pmic-buck125-dvs-gpios = <&gpx0 5 0>,
+						         <&gpx0 6 0>,
+							 <&gpl0 0 0>;
 
 			max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>,
 							 <1250000>, <1200000>,

arch/arm/boot/dts/exynos4210.dtsi

@@ -46,27 +46,17 @@ pinctrl_0: pinctrl@11400000 {
 		compatible = "samsung,pinctrl-exynos4210";
 		reg = <0x11400000 0x1000>;
 		interrupts = <0 47 0>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
 	};
 
 	pinctrl_1: pinctrl@11000000 {
 		compatible = "samsung,pinctrl-exynos4210";
 		reg = <0x11000000 0x1000>;
 		interrupts = <0 46 0>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
 
 		wakup_eint: wakeup-interrupt-controller {
 			compatible = "samsung,exynos4210-wakeup-eint";
 			interrupt-parent = <&gic>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-			interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
-				     <0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>,
-				     <0 24 0>, <0 25 0>, <0 26 0>, <0 27 0>,
-				     <0 28 0>, <0 29 0>, <0 30 0>, <0 31 0>,
-				     <0 32 0>;
+			interrupts = <0 32 0>;
 		};
 	};
 
@@ -75,232 +65,10 @@ pinctrl_2: pinctrl@03860000 {
 		reg = <0x03860000 0x1000>;
 	};
 
-	gpio-controllers {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		gpio-controller;
-		ranges;
-
-		gpa0: gpio-controller@11400000 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400000 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpa1: gpio-controller@11400020 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400020 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpb: gpio-controller@11400040 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400040 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpc0: gpio-controller@11400060 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400060 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpc1: gpio-controller@11400080 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400080 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpd0: gpio-controller@114000A0 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x114000A0 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpd1: gpio-controller@114000C0 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x114000C0 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpe0: gpio-controller@114000E0 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x114000E0 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpe1: gpio-controller@11400100 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400100 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpe2: gpio-controller@11400120 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400120 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpe3: gpio-controller@11400140 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400140 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpe4: gpio-controller@11400160 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400160 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpf0: gpio-controller@11400180 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400180 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpf1: gpio-controller@114001A0 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x114001A0 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpf2: gpio-controller@114001C0 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x114001C0 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpf3: gpio-controller@114001E0 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x114001E0 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpj0: gpio-controller@11000000 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11000000 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpj1: gpio-controller@11000020 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11000020 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpk0: gpio-controller@11000040 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11000040 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpk1: gpio-controller@11000060 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11000060 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpk2: gpio-controller@11000080 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11000080 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpk3: gpio-controller@110000A0 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x110000A0 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpl0: gpio-controller@110000C0 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x110000C0 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpl1: gpio-controller@110000E0 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x110000E0 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpl2: gpio-controller@11000100 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11000100 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpy0: gpio-controller@11000120 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11000120 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpy1: gpio-controller@11000140 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11000140 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpy2: gpio-controller@11000160 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11000160 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpy3: gpio-controller@11000180 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11000180 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpy4: gpio-controller@110001A0 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x110001A0 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpy5: gpio-controller@110001C0 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x110001C0 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpy6: gpio-controller@110001E0 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x110001E0 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpx0: gpio-controller@11000C00 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11000C00 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpx1: gpio-controller@11000C20 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11000C20 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpx2: gpio-controller@11000C40 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11000C40 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpx3: gpio-controller@11000C60 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11000C60 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpz: gpio-controller@03860000 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x03860000 0x20>;
-			#gpio-cells = <4>;
-		};
+	tmu@100C0000 {
+		compatible = "samsung,exynos4210-tmu";
+		interrupt-parent = <&combiner>;
+		reg = <0x100C0000 0x100>;
+		interrupts = <2 4>;
 	};
 };

arch/arm/boot/dts/exynos4212.dtsi

+/*
+ * Samsung's Exynos4212 SoC device tree source
+ *
+ * Copyright (c) 2012 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * Samsung's Exynos4212 SoC device nodes are listed in this file. Exynos4212
+ * based board files can include this file and provide values for board specfic
+ * bindings.
+ *
+ * Note: This file does not include device nodes for all the controllers in
+ * Exynos4212 SoC. As device tree coverage for Exynos4212 increases, additional
+ * nodes can be added to this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/include/ "exynos4x12.dtsi"
+
+/ {
+	compatible = "samsung,exynos4212";
+
+	gic:interrupt-controller@10490000 {
+		cpu-offset = <0x8000>;
+	};
+};

arch/arm/boot/dts/exynos4412-smdk4412.dts

+/*
+ * Samsung's Exynos4412 based SMDK board device tree source
+ *
+ * Copyright (c) 2012-2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * Device tree source file for Samsung's SMDK4412 board which is based on
+ * Samsung's Exynos4412 SoC.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+/include/ "exynos4412.dtsi"
+
+/ {
+	model = "Samsung SMDK evaluation board based on Exynos4412";
+	compatible = "samsung,smdk4412", "samsung,exynos4412";
+
+	memory {
+		reg = <0x40000000 0x40000000>;
+	};
+
+	chosen {
+		bootargs ="root=/dev/ram0 rw ramdisk=8192 initrd=0x41000000,8M console=ttySAC1,115200 init=/linuxrc";
+	};
+
+	serial@13800000 {
+		status = "okay";
+	};
+
+	serial@13810000 {
+		status = "okay";
+	};
+
+	serial@13820000 {
+		status = "okay";
+	};
+
+	serial@13830000 {
+		status = "okay";
+	};
+};

arch/arm/boot/dts/exynos4412.dtsi

+/*
+ * Samsung's Exynos4412 SoC device tree source
+ *
+ * Copyright (c) 2012 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * Samsung's Exynos4412 SoC device nodes are listed in this file. Exynos4412
+ * based board files can include this file and provide values for board specfic
+ * bindings.
+ *
+ * Note: This file does not include device nodes for all the controllers in
+ * Exynos4412 SoC. As device tree coverage for Exynos4412 increases, additional
+ * nodes can be added to this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/include/ "exynos4x12.dtsi"
+
+/ {
+	compatible = "samsung,exynos4412";
+
+	gic:interrupt-controller@10490000 {
+		cpu-offset = <0x4000>;
+	};
+};

arch/arm/boot/dts/exynos4x12.dtsi

+/*
+ * Samsung's Exynos4x12 SoCs device tree source
+ *
+ * Copyright (c) 2012 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * Samsung's Exynos4x12 SoCs device nodes are listed in this file. Exynos4x12
+ * based board files can include this file and provide values for board specfic
+ * bindings.
+ *
+ * Note: This file does not include device nodes for all the controllers in
+ * Exynos4x12 SoC. As device tree coverage for Exynos4x12 increases, additional
+ * nodes can be added to this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/include/ "exynos4.dtsi"
+/include/ "exynos4x12-pinctrl.dtsi"
+
+/ {
+	aliases {
+		pinctrl0 = &pinctrl_0;
+		pinctrl1 = &pinctrl_1;
+		pinctrl2 = &pinctrl_2;
+		pinctrl3 = &pinctrl_3;
+	};
+
+	combiner:interrupt-controller@10440000 {
+		interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
+			     <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
+			     <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
+			     <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>,
+			     <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>;
+	};
+
+	pinctrl_0: pinctrl@11400000 {
+		compatible = "samsung,pinctrl-exynos4x12";
+		reg = <0x11400000 0x1000>;
+		interrupts = <0 47 0>;
+	};
+
+	pinctrl_1: pinctrl@11000000 {
+		compatible = "samsung,pinctrl-exynos4x12";
+		reg = <0x11000000 0x1000>;
+		interrupts = <0 46 0>;
+
+		wakup_eint: wakeup-interrupt-controller {
+			compatible = "samsung,exynos4210-wakeup-eint";
+			interrupt-parent = <&gic>;
+			interrupts = <0 32 0>;
+		};
+	};
+
+	pinctrl_2: pinctrl@03860000 {
+		compatible = "samsung,pinctrl-exynos4x12";
+		reg = <0x03860000 0x1000>;
+		interrupt-parent = <&combiner>;
+		interrupts = <10 0>;
+	};
+
+	pinctrl_3: pinctrl@106E0000 {
+		compatible = "samsung,pinctrl-exynos4x12";
+		reg = <0x106E0000 0x1000>;
+		interrupts = <0 72 0>;
+	};
+};

arch/arm/boot/dts/exynos5250-smdk5250.dts

@@ -55,6 +55,21 @@ eeprom@51 {
 		};
 	};
 
+	i2c@121D0000 {
+		samsung,i2c-sda-delay = <100>;
+		samsung,i2c-max-bus-freq = <40000>;
+		samsung,i2c-slave-addr = <0x38>;
+
+		sata-phy {
+			compatible = "samsung,sata-phy";
+			reg = <0x38>;
+		};
+	};
+
+	sata@122F0000 {
+		samsung,sata-freq = <66>;
+	};
+
 	i2c@12C80000 {
 		samsung,i2c-sda-delay = <100>;
 		samsung,i2c-max-bus-freq = <66000>;
@@ -188,4 +203,9 @@ spi_2: spi@12d40000 {
 	hdmi {
 		hpd-gpio = <&gpx3 7 0xf 1 3>;
 	};
+
+	codec@11000000 {
+		samsung,mfc-r = <0x43000000 0x800000>;
+		samsung,mfc-l = <0x51000000 0x800000>;
+	};
 };

arch/arm/boot/dts/exynos5250.dtsi

@@ -62,12 +62,24 @@ watchdog {
 		interrupts = <0 42 0>;
 	};
 
+	codec@11000000 {
+		compatible = "samsung,mfc-v6";
+		reg = <0x11000000 0x10000>;
+		interrupts = <0 96 0>;
+	};
+
 	rtc {
 		compatible = "samsung,s3c6410-rtc";
 		reg = <0x101E0000 0x100>;
 		interrupts = <0 43 0>, <0 44 0>;
 	};
 
+	tmu@10060000 {
+		compatible = "samsung,exynos5250-tmu";
+		reg = <0x10060000 0x100>;
+		interrupts = <0 65 0>;
+	};
+
 	serial@12C00000 {
 		compatible = "samsung,exynos4210-uart";
 		reg = <0x12C00000 0x100>;
@@ -92,6 +104,17 @@ serial@12C30000 {
 		interrupts = <0 54 0>;
 	};
 
+	sata@122F0000 {
+		compatible = "samsung,exynos5-sata-ahci";
+		reg = <0x122F0000 0x1ff>;
+		interrupts = <0 115 0>;
+	};
+
+	sata-phy@12170000 {
+		compatible = "samsung,exynos5-sata-phy";
+		reg = <0x12170000 0x1ff>;
+	};
+
 	i2c@12C60000 {
 		compatible = "samsung,s3c2440-i2c";
 		reg = <0x12C60000 0x100>;
@@ -164,6 +187,13 @@ i2c@12CE0000 {
 		#size-cells = <0>;
 	};
 
+	i2c@121D0000 {
+                compatible = "samsung,exynos5-sata-phy-i2c";
+                reg = <0x121D0000 0x100>;
+                #address-cells = <1>;
+                #size-cells = <0>;
+	};
+
 	spi_0: spi@12d20000 {
 		compatible = "samsung,exynos4210-spi";
 		reg = <0x12d20000 0x100>;

arch/arm/mach-exynos/Kconfig

@@ -63,6 +63,7 @@ config SOC_EXYNOS5250
 	depends on ARCH_EXYNOS5
 	select S5P_PM if PM
 	select S5P_SLEEP if PM
+	select S5P_DEV_MFC
 	select SAMSUNG_DMADEV
 	help
 	  Enable EXYNOS5250 SoC support

arch/arm/mach-exynos/clock-exynos4.c

@@ -575,6 +575,10 @@ static struct clk exynos4_init_clocks_off[] = {
 		.name		= "adc",
 		.enable		= exynos4_clk_ip_peril_ctrl,
 		.ctrlbit	= (1 << 15),
+	}, {
+		.name		= "tmu_apbif",
+		.enable		= exynos4_clk_ip_perir_ctrl,
+		.ctrlbit	= (1 << 17),
 	}, {
 		.name		= "keypad",
 		.enable		= exynos4_clk_ip_perir_ctrl,

arch/arm/mach-exynos/clock-exynos5.c

@@ -620,6 +620,11 @@ static struct clk exynos5_init_clocks_off[] = {
 		.parent		= &exynos5_clk_aclk_66.clk,
 		.enable		= exynos5_clk_ip_peric_ctrl,
 		.ctrlbit	= (1 << 24),
+	}, {
+		.name		= "tmu_apbif",
+		.parent		= &exynos5_clk_aclk_66.clk,
+		.enable		= exynos5_clk_ip_peris_ctrl,
+		.ctrlbit	= (1 << 21),
 	}, {
 		.name		= "rtc",
 		.parent		= &exynos5_clk_aclk_66.clk,
@@ -669,7 +674,7 @@ static struct clk exynos5_init_clocks_off[] = {
 		.ctrlbit	= (1 << 25),
 	}, {
 		.name		= "mfc",
-		.devname	= "s5p-mfc",
+		.devname	= "s5p-mfc-v6",
 		.enable		= exynos5_clk_ip_mfc_ctrl,
 		.ctrlbit	= (1 << 0),
 	}, {

arch/arm/mach-exynos/common.c

@@ -997,11 +997,14 @@ static int __init exynos_init_irq_eint(void)
 	 * platforms switch over to using the pinctrl driver, the wakeup
 	 * interrupt support code here can be completely removed.
 	 */
+	static const struct of_device_id exynos_pinctrl_ids[] = {
+		{ .compatible = "samsung,pinctrl-exynos4210", },
+		{ .compatible = "samsung,pinctrl-exynos4x12", },
+	};
 	struct device_node *pctrl_np, *wkup_np;
-	const char *pctrl_compat = "samsung,pinctrl-exynos4210";
 	const char *wkup_compat = "samsung,exynos4210-wakeup-eint";
 
-	for_each_compatible_node(pctrl_np, NULL, pctrl_compat) {
+	for_each_matching_node(pctrl_np, exynos_pinctrl_ids) {
 		if (of_device_is_available(pctrl_np)) {
 			wkup_np = of_find_compatible_node(pctrl_np, NULL,
 							wkup_compat);

arch/arm/mach-exynos/include/mach/irqs.h

@@ -136,6 +136,9 @@
 #define EXYNOS4_IRQ_TSI			IRQ_SPI(115)
 #define EXYNOS4_IRQ_SATA		IRQ_SPI(116)
 
+#define EXYNOS4_IRQ_TMU_TRIG0		COMBINER_IRQ(2, 4)
+#define EXYNOS4_IRQ_TMU_TRIG1		COMBINER_IRQ(3, 4)
+
 #define EXYNOS4_IRQ_SYSMMU_MDMA0_0	COMBINER_IRQ(4, 0)
 #define EXYNOS4_IRQ_SYSMMU_SSS_0	COMBINER_IRQ(4, 1)
 #define EXYNOS4_IRQ_SYSMMU_FIMC0_0	COMBINER_IRQ(4, 2)

arch/arm/mach-exynos/include/mach/map.h

@@ -88,6 +88,8 @@
 #define EXYNOS4_PA_TWD			0x10500600
 #define EXYNOS4_PA_L2CC			0x10502000
 
+#define EXYNOS4_PA_TMU			0x100C0000
+
 #define EXYNOS4_PA_MDMA0		0x10810000
 #define EXYNOS4_PA_MDMA1		0x12850000
 #define EXYNOS4_PA_PDMA0		0x12680000

arch/arm/mach-exynos/mach-exynos4-dt.c

@@ -77,6 +77,8 @@ static const struct of_dev_auxdata exynos4_auxdata_lookup[] __initconst = {
 				"exynos4210-spi.2", NULL),
 	OF_DEV_AUXDATA("arm,pl330", EXYNOS4_PA_PDMA0, "dma-pl330.0", NULL),
 	OF_DEV_AUXDATA("arm,pl330", EXYNOS4_PA_PDMA1, "dma-pl330.1", NULL),
+	OF_DEV_AUXDATA("samsung,exynos4210-tmu", EXYNOS4_PA_TMU,
+				"exynos-tmu", NULL),
 	{},
 };
 
@@ -94,6 +96,8 @@ static void __init exynos4_dt_machine_init(void)
 
 static char const *exynos4_dt_compat[] __initdata = {
 	"samsung,exynos4210",
+	"samsung,exynos4212",
+	"samsung,exynos4412",
 	NULL
 };
 

arch/arm/mach-exynos/mach-exynos5-dt.c

@@ -11,6 +11,8 @@
 
 #include <linux/of_platform.h>
 #include <linux/serial_core.h>
+#include <linux/memblock.h>
+#include <linux/of_fdt.h>
 
 #include <asm/mach/arch.h>
 #include <asm/hardware/gic.h>
@@ -18,6 +20,7 @@
 
 #include <plat/cpu.h>
 #include <plat/regs-serial.h>
+#include <plat/mfc.h>
 
 #include "common.h"
 
@@ -65,6 +68,12 @@ static const struct of_dev_auxdata exynos5250_auxdata_lookup[] __initconst = {
 				"exynos4210-spi.1", NULL),
 	OF_DEV_AUXDATA("samsung,exynos4210-spi", EXYNOS5_PA_SPI2,
 				"exynos4210-spi.2", NULL),
+	OF_DEV_AUXDATA("samsung,exynos5-sata-ahci", 0x122F0000,
+				"exynos5-sata", NULL),
+	OF_DEV_AUXDATA("samsung,exynos5-sata-phy", 0x12170000,
+				"exynos5-sata-phy", NULL),
+	OF_DEV_AUXDATA("samsung,exynos5-sata-phy-i2c", 0x121D0000,
+				"exynos5-sata-phy-i2c", NULL),
 	OF_DEV_AUXDATA("arm,pl330", EXYNOS5_PA_PDMA0, "dma-pl330.0", NULL),
 	OF_DEV_AUXDATA("arm,pl330", EXYNOS5_PA_PDMA1, "dma-pl330.1", NULL),
 	OF_DEV_AUXDATA("arm,pl330", EXYNOS5_PA_MDMA1, "dma-pl330.2", NULL),
@@ -80,6 +89,9 @@ static const struct of_dev_auxdata exynos5250_auxdata_lookup[] __initconst = {
 				"exynos5-hdmi", NULL),
 	OF_DEV_AUXDATA("samsung,exynos5-mixer", 0x14450000,
 				"exynos5-mixer", NULL),
+	OF_DEV_AUXDATA("samsung,mfc-v6", 0x11000000, "s5p-mfc-v6", NULL),
+	OF_DEV_AUXDATA("samsung,exynos5250-tmu", 0x10060000,
+				"exynos-tmu", NULL),
 	{},
 };
 
@@ -100,6 +112,17 @@ static char const *exynos5250_dt_compat[] __initdata = {
 	NULL
 };
 
+static void __init exynos5_reserve(void)
+{
+	struct s5p_mfc_dt_meminfo mfc_mem;
+
+	/* Reserve memory for MFC only if it's available */
+	mfc_mem.compatible = "samsung,mfc-v6";
+	if (of_scan_flat_dt(s5p_fdt_find_mfc_mem, &mfc_mem))
+		s5p_mfc_reserve_mem(mfc_mem.roff, mfc_mem.rsize, mfc_mem.loff,
+				mfc_mem.lsize);
+}
+
 DT_MACHINE_START(EXYNOS5_DT, "SAMSUNG EXYNOS5 (Flattened Device Tree)")
 	/* Maintainer: Kukjin Kim <kgene.kim@samsung.com> */
 	.init_irq	= exynos5_init_irq,
@@ -111,4 +134,5 @@ DT_MACHINE_START(EXYNOS5_DT, "SAMSUNG EXYNOS5 (Flattened Device Tree)")
 	.timer		= &exynos4_timer,
 	.dt_compat	= exynos5250_dt_compat,
 	.restart        = exynos5_restart,
+	.reserve	= exynos5_reserve,
 MACHINE_END

arch/arm/plat-samsung/devs.c

@@ -933,6 +933,7 @@ struct platform_device s5p_device_mfc_r = {
 		.coherent_dma_mask	= DMA_BIT_MASK(32),
 	},
 };
+
 #endif /* CONFIG_S5P_DEV_MFC */
 
 /* MIPI CSIS */

arch/arm/plat-samsung/include/plat/mfc.h

@@ -10,6 +10,14 @@
 #ifndef __PLAT_SAMSUNG_MFC_H
 #define __PLAT_SAMSUNG_MFC_H __FILE__
 
+struct s5p_mfc_dt_meminfo {
+	unsigned long	loff;
+	unsigned long	lsize;
+	unsigned long	roff;
+	unsigned long	rsize;
+	char		*compatible;
+};
+
 /**
  * s5p_mfc_reserve_mem - function to early reserve memory for MFC driver
  * @rbase:	base address for MFC 'right' memory interface
@@ -24,4 +32,7 @@
 void __init s5p_mfc_reserve_mem(phys_addr_t rbase, unsigned int rsize,
 				phys_addr_t lbase, unsigned int lsize);
 
+int __init s5p_fdt_find_mfc_mem(unsigned long node, const char *uname,
+				int depth, void *data);
+
 #endif /* __PLAT_SAMSUNG_MFC_H */

arch/arm/plat-samsung/s5p-dev-mfc.c

@@ -14,6 +14,8 @@
 #include <linux/dma-mapping.h>
 #include <linux/memblock.h>
 #include <linux/ioport.h>
+#include <linux/of_fdt.h>
+#include <linux/of.h>
 
 #include <mach/map.h>
 #include <plat/devs.h>
@@ -69,3 +71,35 @@ static int __init s5p_mfc_memory_init(void)
 	return 0;
 }
 device_initcall(s5p_mfc_memory_init);
+
+#ifdef CONFIG_OF
+int __init s5p_fdt_find_mfc_mem(unsigned long node, const char *uname,
+				int depth, void *data)
+{
+	__be32 *prop;
+	unsigned long len;
+	struct s5p_mfc_dt_meminfo *mfc_mem = data;
+
+	if (!data)
+		return 0;
+
+	if (!of_flat_dt_is_compatible(node, mfc_mem->compatible))
+		return 0;
+
+	prop = of_get_flat_dt_prop(node, "samsung,mfc-l", &len);
+	if (!prop || (len != 2 * sizeof(unsigned long)))
+		return 0;
+
+	mfc_mem->loff = be32_to_cpu(prop[0]);
+	mfc_mem->lsize = be32_to_cpu(prop[1]);
+
+	prop = of_get_flat_dt_prop(node, "samsung,mfc-r", &len);
+	if (!prop || (len != 2 * sizeof(unsigned long)))
+		return 0;
+
+	mfc_mem->roff = be32_to_cpu(prop[0]);
+	mfc_mem->rsize = be32_to_cpu(prop[1]);
+
+	return 1;
+}
+#endif

drivers/gpio/gpio-samsung.c

@@ -2797,27 +2797,6 @@ static __init void exynos4_gpiolib_init(void)
 	int group = 0;
 	void __iomem *gpx_base;
 
-#ifdef CONFIG_PINCTRL_SAMSUNG
-		/*
-		 * This gpio driver includes support for device tree support and
-		 * there are platforms using it. In order to maintain
-		 * compatibility with those platforms, and to allow non-dt
-		 * Exynos4210 platforms to use this gpiolib support, a check
-		 * is added to find out if there is a active pin-controller
-		 * driver support available. If it is available, this gpiolib
-		 * support is ignored and the gpiolib support available in
-		 * pin-controller driver is used. This is a temporary check and
-		 * will go away when all of the Exynos4210 platforms have
-		 * switched to using device tree and the pin-ctrl driver.
-		 */
-		struct device_node *pctrl_np;
-		const char *pctrl_compat = "samsung,pinctrl-exynos4210";
-		pctrl_np = of_find_compatible_node(NULL, NULL, pctrl_compat);
-		if (pctrl_np)
-			if (of_device_is_available(pctrl_np))
-				return;
-#endif
-
 	/* gpio part1 */
 	gpio_base1 = ioremap(EXYNOS4_PA_GPIO1, SZ_4K);
 	if (gpio_base1 == NULL) {
@@ -3032,6 +3011,28 @@ static __init int samsung_gpiolib_init(void)
 	int i, nr_chips;
 	int group = 0;
 
+#ifdef CONFIG_PINCTRL_SAMSUNG
+	/*
+	* This gpio driver includes support for device tree support and there
+	* are platforms using it. In order to maintain compatibility with those
+	* platforms, and to allow non-dt Exynos4210 platforms to use this
+	* gpiolib support, a check is added to find out if there is a active
+	* pin-controller driver support available. If it is available, this
+	* gpiolib support is ignored and the gpiolib support available in
+	* pin-controller driver is used. This is a temporary check and will go
+	* away when all of the Exynos4210 platforms have switched to using
+	* device tree and the pin-ctrl driver.
+	*/
+	struct device_node *pctrl_np;
+	static const struct of_device_id exynos_pinctrl_ids[] = {
+		{ .compatible = "samsung,pinctrl-exynos4210", },
+		{ .compatible = "samsung,pinctrl-exynos4x12", },
+	};
+	for_each_matching_node(pctrl_np, exynos_pinctrl_ids)
+		if (pctrl_np && of_device_is_available(pctrl_np))
+			return -ENODEV;
+#endif
+
 	samsung_gpiolib_set_cfg(samsung_gpio_cfgs, ARRAY_SIZE(samsung_gpio_cfgs));
 
 	if (soc_is_s3c24xx()) {

drivers/pinctrl/pinctrl-exynos.h

@@ -17,125 +17,6 @@
  * (at your option) any later version.
  */
 
-#define EXYNOS_GPIO_START(__gpio)	((__gpio##_START) + (__gpio##_NR))
-
-#define EXYNOS4210_GPIO_A0_NR	(8)
-#define EXYNOS4210_GPIO_A1_NR	(6)
-#define EXYNOS4210_GPIO_B_NR	(8)
-#define EXYNOS4210_GPIO_C0_NR	(5)
-#define EXYNOS4210_GPIO_C1_NR	(5)
-#define EXYNOS4210_GPIO_D0_NR	(4)
-#define EXYNOS4210_GPIO_D1_NR	(4)
-#define EXYNOS4210_GPIO_E0_NR	(5)
-#define EXYNOS4210_GPIO_E1_NR	(8)
-#define EXYNOS4210_GPIO_E2_NR	(6)
-#define EXYNOS4210_GPIO_E3_NR	(8)
-#define EXYNOS4210_GPIO_E4_NR	(8)
-#define EXYNOS4210_GPIO_F0_NR	(8)
-#define EXYNOS4210_GPIO_F1_NR	(8)
-#define EXYNOS4210_GPIO_F2_NR	(8)
-#define EXYNOS4210_GPIO_F3_NR	(6)
-#define EXYNOS4210_GPIO_J0_NR	(8)
-#define EXYNOS4210_GPIO_J1_NR	(5)
-#define EXYNOS4210_GPIO_K0_NR	(7)
-#define EXYNOS4210_GPIO_K1_NR	(7)
-#define EXYNOS4210_GPIO_K2_NR	(7)
-#define EXYNOS4210_GPIO_K3_NR	(7)
-#define EXYNOS4210_GPIO_L0_NR	(8)
-#define EXYNOS4210_GPIO_L1_NR	(3)
-#define EXYNOS4210_GPIO_L2_NR	(8)
-#define EXYNOS4210_GPIO_Y0_NR	(6)
-#define EXYNOS4210_GPIO_Y1_NR	(4)
-#define EXYNOS4210_GPIO_Y2_NR	(6)
-#define EXYNOS4210_GPIO_Y3_NR	(8)
-#define EXYNOS4210_GPIO_Y4_NR	(8)
-#define EXYNOS4210_GPIO_Y5_NR	(8)
-#define EXYNOS4210_GPIO_Y6_NR	(8)
-#define EXYNOS4210_GPIO_X0_NR	(8)
-#define EXYNOS4210_GPIO_X1_NR	(8)
-#define EXYNOS4210_GPIO_X2_NR	(8)
-#define EXYNOS4210_GPIO_X3_NR	(8)
-#define EXYNOS4210_GPIO_Z_NR	(7)
-
-enum exynos4210_gpio_xa_start {
-	EXYNOS4210_GPIO_A0_START	= 0,
-	EXYNOS4210_GPIO_A1_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_A0),
-	EXYNOS4210_GPIO_B_START		= EXYNOS_GPIO_START(EXYNOS4210_GPIO_A1),
-	EXYNOS4210_GPIO_C0_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_B),
-	EXYNOS4210_GPIO_C1_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_C0),
-	EXYNOS4210_GPIO_D0_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_C1),
-	EXYNOS4210_GPIO_D1_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_D0),
-	EXYNOS4210_GPIO_E0_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_D1),
-	EXYNOS4210_GPIO_E1_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_E0),
-	EXYNOS4210_GPIO_E2_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_E1),
-	EXYNOS4210_GPIO_E3_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_E2),
-	EXYNOS4210_GPIO_E4_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_E3),
-	EXYNOS4210_GPIO_F0_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_E4),
-	EXYNOS4210_GPIO_F1_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_F0),
-	EXYNOS4210_GPIO_F2_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_F1),
-	EXYNOS4210_GPIO_F3_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_F2),
-};
-
-enum exynos4210_gpio_xb_start {
-	EXYNOS4210_GPIO_J0_START	= 0,
-	EXYNOS4210_GPIO_J1_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_J0),
-	EXYNOS4210_GPIO_K0_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_J1),
-	EXYNOS4210_GPIO_K1_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_K0),
-	EXYNOS4210_GPIO_K2_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_K1),
-	EXYNOS4210_GPIO_K3_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_K2),
-	EXYNOS4210_GPIO_L0_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_K3),
-	EXYNOS4210_GPIO_L1_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_L0),
-	EXYNOS4210_GPIO_L2_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_L1),
-	EXYNOS4210_GPIO_Y0_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_L2),
-	EXYNOS4210_GPIO_Y1_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_Y0),
-	EXYNOS4210_GPIO_Y2_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_Y1),
-	EXYNOS4210_GPIO_Y3_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_Y2),
-	EXYNOS4210_GPIO_Y4_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_Y3),
-	EXYNOS4210_GPIO_Y5_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_Y4),
-	EXYNOS4210_GPIO_Y6_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_Y5),
-	EXYNOS4210_GPIO_X0_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_Y6),
-	EXYNOS4210_GPIO_X1_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_X0),
-	EXYNOS4210_GPIO_X2_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_X1),
-	EXYNOS4210_GPIO_X3_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_X2),
-};
-
-enum exynos4210_gpio_xc_start {
-	EXYNOS4210_GPIO_Z_START		= 0,
-};
-
-#define	EXYNOS4210_GPIO_A0_IRQ		EXYNOS4210_GPIO_A0_START
-#define	EXYNOS4210_GPIO_A1_IRQ		EXYNOS4210_GPIO_A1_START
-#define	EXYNOS4210_GPIO_B_IRQ		EXYNOS4210_GPIO_B_START
-#define	EXYNOS4210_GPIO_C0_IRQ		EXYNOS4210_GPIO_C0_START
-#define	EXYNOS4210_GPIO_C1_IRQ		EXYNOS4210_GPIO_C1_START
-#define	EXYNOS4210_GPIO_D0_IRQ		EXYNOS4210_GPIO_D0_START
-#define	EXYNOS4210_GPIO_D1_IRQ		EXYNOS4210_GPIO_D1_START
-#define	EXYNOS4210_GPIO_E0_IRQ		EXYNOS4210_GPIO_E0_START
-#define	EXYNOS4210_GPIO_E1_IRQ		EXYNOS4210_GPIO_E1_START
-#define	EXYNOS4210_GPIO_E2_IRQ		EXYNOS4210_GPIO_E2_START
-#define	EXYNOS4210_GPIO_E3_IRQ		EXYNOS4210_GPIO_E3_START
-#define	EXYNOS4210_GPIO_E4_IRQ		EXYNOS4210_GPIO_E4_START
-#define	EXYNOS4210_GPIO_F0_IRQ		EXYNOS4210_GPIO_F0_START
-#define	EXYNOS4210_GPIO_F1_IRQ		EXYNOS4210_GPIO_F1_START
-#define	EXYNOS4210_GPIO_F2_IRQ		EXYNOS4210_GPIO_F2_START
-#define	EXYNOS4210_GPIO_F3_IRQ		EXYNOS4210_GPIO_F3_START
-#define	EXYNOS4210_GPIO_J0_IRQ		EXYNOS4210_GPIO_J0_START
-#define	EXYNOS4210_GPIO_J1_IRQ		EXYNOS4210_GPIO_J1_START
-#define	EXYNOS4210_GPIO_K0_IRQ		EXYNOS4210_GPIO_K0_START
-#define	EXYNOS4210_GPIO_K1_IRQ		EXYNOS4210_GPIO_K1_START
-#define	EXYNOS4210_GPIO_K2_IRQ		EXYNOS4210_GPIO_K2_START
-#define	EXYNOS4210_GPIO_K3_IRQ		EXYNOS4210_GPIO_K3_START
-#define	EXYNOS4210_GPIO_L0_IRQ		EXYNOS4210_GPIO_L0_START
-#define	EXYNOS4210_GPIO_L1_IRQ		EXYNOS4210_GPIO_L1_START
-#define	EXYNOS4210_GPIO_L2_IRQ		EXYNOS4210_GPIO_L2_START
-#define	EXYNOS4210_GPIO_Z_IRQ		EXYNOS4210_GPIO_Z_START
-
-#define EXYNOS4210_GPIOA_NR_PINS	EXYNOS_GPIO_START(EXYNOS4210_GPIO_F3)
-#define EXYNOS4210_GPIOA_NR_GINT	EXYNOS_GPIO_START(EXYNOS4210_GPIO_F3)
-#define EXYNOS4210_GPIOB_NR_PINS	EXYNOS_GPIO_START(EXYNOS4210_GPIO_X3)
-#define EXYNOS4210_GPIOB_NR_GINT	EXYNOS_GPIO_START(EXYNOS4210_GPIO_L2)
-#define EXYNOS4210_GPIOC_NR_PINS	EXYNOS_GPIO_START(EXYNOS4210_GPIO_Z)
-
 /* External GPIO and wakeup interrupt related definitions */
 #define EXYNOS_GPIO_ECON_OFFSET		0x700
 #define EXYNOS_GPIO_EMASK_OFFSET	0x900
@@ -165,11 +46,10 @@ enum exynos4210_gpio_xc_start {
 #define EXYNOS_EINT_MAX_PER_BANK	8
 #define EXYNOS_EINT_NR_WKUP_EINT
 
-#define EXYNOS_PIN_BANK_EINTN(reg, __gpio, id)		\
+#define EXYNOS_PIN_BANK_EINTN(pins, reg, id)		\
 	{						\
 		.pctl_offset	= reg,			\
-		.pin_base	= (__gpio##_START),	\
-		.nr_pins	= (__gpio##_NR),	\
+		.nr_pins	= pins,			\
 		.func_width	= 4,			\
 		.pud_width	= 2,			\
 		.drv_width	= 2,			\
@@ -179,40 +59,50 @@ enum exynos4210_gpio_xc_start {
 		.name		= id			\
 	}
 
-#define EXYNOS_PIN_BANK_EINTG(reg, __gpio, id)		\
+#define EXYNOS_PIN_BANK_EINTG(pins, reg, id, offs)	\
 	{						\
 		.pctl_offset	= reg,			\
-		.pin_base	= (__gpio##_START),	\
-		.nr_pins	= (__gpio##_NR),	\
+		.nr_pins	= pins,			\
 		.func_width	= 4,			\
 		.pud_width	= 2,			\
 		.drv_width	= 2,			\
 		.conpdn_width	= 2,			\
 		.pudpdn_width	= 2,			\
 		.eint_type	= EINT_TYPE_GPIO,	\
-		.irq_base	= (__gpio##_IRQ),	\
+		.eint_offset	= offs,			\
 		.name		= id			\
 	}
 
-/**
- * struct exynos_geint_data: gpio eint specific data for irq_chip callbacks.
- * @bank: pin bank from which this gpio interrupt originates.
- * @pin: pin number within the bank.
- * @eint_offset: offset to be added to the con/pend/mask register bank base.
- */
-struct exynos_geint_data {
-	struct samsung_pin_bank	*bank;
-	u32			pin;
-	u32			eint_offset;
-};
+#define EXYNOS_PIN_BANK_EINTW(pins, reg, id, offs)	\
+	{						\
+		.pctl_offset	= reg,			\
+		.nr_pins	= pins,			\
+		.func_width	= 4,			\
+		.pud_width	= 2,			\
+		.drv_width	= 2,			\
+		.eint_type	= EINT_TYPE_WKUP,	\
+		.eint_offset	= offs,			\
+		.name		= id			\
+	}
 
 /**
  * struct exynos_weint_data: irq specific data for all the wakeup interrupts
  * generated by the external wakeup interrupt controller.
- * @domain: irq domain representing the external wakeup interrupts
  * @irq: interrupt number within the domain.
+ * @bank: bank responsible for this interrupt
  */
 struct exynos_weint_data {
-	struct irq_domain	*domain;
-	u32			irq;
+	unsigned int irq;
+	struct samsung_pin_bank *bank;
+};
+
+/**
+ * struct exynos_muxed_weint_data: irq specific data for muxed wakeup interrupts
+ * generated by the external wakeup interrupt controller.
+ * @nr_banks: count of banks being part of the mux
+ * @banks: array of banks being part of the mux
+ */
+struct exynos_muxed_weint_data {
+	unsigned int nr_banks;
+	struct samsung_pin_bank *banks[];
 };

drivers/pinctrl/pinctrl-samsung.h

@@ -23,6 +23,8 @@
 #include <linux/pinctrl/consumer.h>
 #include <linux/pinctrl/machine.h>
 
+#include <linux/gpio.h>
+
 /* register offsets within a pin bank */
 #define DAT_REG		0x4
 #define PUD_REG		0x8
@@ -64,6 +66,7 @@ enum pincfg_type {
  * @EINT_TYPE_NONE: bank does not support external interrupts
  * @EINT_TYPE_GPIO: bank supportes external gpio interrupts
  * @EINT_TYPE_WKUP: bank supportes external wakeup interrupts
+ * @EINT_TYPE_WKUP_MUX: bank supports multiplexed external wakeup interrupts
  *
  * Samsung GPIO controller groups all the available pins into banks. The pins
  * in a pin bank can support external gpio interrupts or external wakeup
@@ -76,6 +79,7 @@ enum eint_type {
 	EINT_TYPE_NONE,
 	EINT_TYPE_GPIO,
 	EINT_TYPE_WKUP,
+	EINT_TYPE_WKUP_MUX,
 };
 
 /* maximum length of a pin in pin descriptor (example: "gpa0-0") */
@@ -109,8 +113,12 @@ struct samsung_pinctrl_drv_data;
  * @conpdn_width: width of the sleep mode function selector bin field.
  * @pudpdn_width: width of the sleep mode pull up/down selector bit field.
  * @eint_type: type of the external interrupt supported by the bank.
- * @irq_base: starting controller local irq number of the bank.
  * @name: name to be prefixed for each pin in this pin bank.
+ * @of_node: OF node of the bank.
+ * @drvdata: link to controller driver data
+ * @irq_domain: IRQ domain of the bank.
+ * @gpio_chip: GPIO chip of the bank.
+ * @grange: linux gpio pin range supported by this bank.
  */
 struct samsung_pin_bank {
 	u32		pctl_offset;
@@ -122,8 +130,13 @@ struct samsung_pin_bank {
 	u8		conpdn_width;
 	u8		pudpdn_width;
 	enum eint_type	eint_type;
-	u32		irq_base;
+	u32		eint_offset;
 	char		*name;
+	struct device_node *of_node;
+	struct samsung_pinctrl_drv_data *drvdata;
+	struct irq_domain *irq_domain;
+	struct gpio_chip gpio_chip;
+	struct pinctrl_gpio_range grange;
 };
 
 /**
@@ -132,8 +145,6 @@ struct samsung_pin_bank {
  * @nr_banks: number of pin banks.
  * @base: starting system wide pin number.
  * @nr_pins: number of pins supported by the controller.
- * @nr_gint: number of external gpio interrupts supported.
- * @nr_wint: number of external wakeup interrupts supported.
  * @geint_con: offset of the ext-gpio controller registers.
  * @geint_mask: offset of the ext-gpio interrupt mask registers.
  * @geint_pend: offset of the ext-gpio interrupt pending registers.
@@ -153,8 +164,6 @@ struct samsung_pin_ctrl {
 
 	u32		base;
 	u32		nr_pins;
-	u32		nr_gint;
-	u32		nr_wint;
 
 	u32		geint_con;
 	u32		geint_mask;
@@ -183,8 +192,6 @@ struct samsung_pin_ctrl {
  * @nr_groups: number of such pin groups.
  * @pmx_functions: list of pin functions available to the driver.
  * @nr_function: number of such pin functions.
- * @gc: gpio_chip instance registered with gpiolib.
- * @grange: linux gpio pin range supported by this controller.
  */
 struct samsung_pinctrl_drv_data {
 	void __iomem			*virt_base;
@@ -199,12 +206,6 @@ struct samsung_pinctrl_drv_data {
 	unsigned int			nr_groups;
 	const struct samsung_pmx_func	*pmx_functions;
 	unsigned int			nr_functions;
-
-	struct irq_domain		*gpio_irqd;
-	struct irq_domain		*wkup_irqd;
-
-	struct gpio_chip		*gc;
-	struct pinctrl_gpio_range	grange;
 };
 
 /**
@@ -235,5 +236,6 @@ struct samsung_pmx_func {
 
 /* list of all exported SoC specific data */
 extern struct samsung_pin_ctrl exynos4210_pin_ctrl[];
+extern struct samsung_pin_ctrl exynos4x12_pin_ctrl[];
 
 #endif /* __PINCTRL_SAMSUNG_H */