Commit 281b0539 authored by Linus Torvalds's avatar Linus Torvalds

Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull "ARM: SoC specific updates" from Arnd Bergmann:
 "These changes are all specific to an soc family or the code for one
  soc.  Lots of work for Tegra3 this time, but also a lot of other
  platforms.  There will be another (smaller) set of soc patches later
  in the merge window for stuff that has dependencies on external trees
  or that was sent just before the merge window opened.

  The asoc tree added a few devices to the i.mx platform, which conflict
  with other devices added in the same place here.

  The tegra Makefile conflicts between a number of branches, mostly
  because of changes regarding localtimer.c, which was removed in the
  end.

  Signed-off-by: Arnd Bergmann <arnd@arndb.de>"

Fix up some trivial conflicts, including the mentioned Tegra Makefile.

* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
  ARM: EXYNOS: fix cycle count for periodic mode of clock event timers
  ARM: EXYNOS: add support JPEG
  ARM: EXYNOS: Add DMC1, allow PPMU access for DMC
  ARM: SAMSUNG: Correct MIPI-CSIS io memory resource definition
  ARM: SAMSUNG: fix __init attribute on regarding s3c_set_platdata()
  ARM: SAMSUNG: Add __init attribute to samsung_bl_set()
  ARM: S5PV210: Add usb otg phy control
  ARM: S3C64XX: Add usb otg phy control
  ARM: EXYNOS: Enable l2 configuration through device tree
  ARM: EXYNOS: remove useless code to save/restore L2
  ARM: EXYNOS: save L2 settings during bootup
  ARM: S5P: add L2 early resume code
  ARM: EXYNOS: Add support AFTR mode on EXYNOS4210
  ARM: mx35: Setup the AIPS registers
  ARM: mx5: Use common function for configuring AIPS
  ARM: mx3: Setup AIPS registers
  ARM: mx3: Let mx31 and mx35 enter in LPM mode in WFI
  ARM: defconfig: imx_v6_v7: build in REGULATOR_FIXED_VOLTAGE
  ARM: imx: update imx_v6_v7_defconfig
  ARM: tegra: Demote EMC clock inconsistency BUG to WARN
  ...
parents 48d55441 bde75567
...@@ -1131,6 +1131,7 @@ config PLAT_VERSATILE ...@@ -1131,6 +1131,7 @@ config PLAT_VERSATILE
config ARM_TIMER_SP804 config ARM_TIMER_SP804
bool bool
select CLKSRC_MMIO select CLKSRC_MMIO
select HAVE_SCHED_CLOCK
source arch/arm/mm/Kconfig source arch/arm/mm/Kconfig
......
/*
* at91sam9g25ek.dts - Device Tree file for AT91SAM9G25-EK board
*
* Copyright (C) 2012 Atmel,
* 2012 Nicolas Ferre <nicolas.ferre@atmel.com>
*
* Licensed under GPLv2 or later.
*/
/dts-v1/;
/include/ "at91sam9x5.dtsi"
/include/ "at91sam9x5cm.dtsi"
/ {
model = "Atmel AT91SAM9G25-EK";
compatible = "atmel,at91sam9g25ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
chosen {
bootargs = "128M console=ttyS0,115200 mtdparts=atmel_nand:8M(bootstrap/uboot/kernel)ro,-(rootfs) root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs";
};
ahb {
apb {
dbgu: serial@fffff200 {
status = "okay";
};
usart0: serial@f801c000 {
status = "okay";
};
macb0: ethernet@f802c000 {
phy-mode = "rmii";
status = "okay";
};
};
};
};
/*
* at91sam9x5.dtsi - Device Tree Include file for AT91SAM9x5 family SoC
* applies to AT91SAM9G15, AT91SAM9G25, AT91SAM9G35,
* AT91SAM9X25, AT91SAM9X35 SoC
*
* Copyright (C) 2012 Atmel,
* 2012 Nicolas Ferre <nicolas.ferre@atmel.com>
*
* Licensed under GPLv2 or later.
*/
/include/ "skeleton.dtsi"
/ {
model = "Atmel AT91SAM9x5 family SoC";
compatible = "atmel,at91sam9x5";
interrupt-parent = <&aic>;
aliases {
serial0 = &dbgu;
serial1 = &usart0;
serial2 = &usart1;
serial3 = &usart2;
gpio0 = &pioA;
gpio1 = &pioB;
gpio2 = &pioC;
gpio3 = &pioD;
tcb0 = &tcb0;
tcb1 = &tcb1;
};
cpus {
cpu@0 {
compatible = "arm,arm926ejs";
};
};
memory@20000000 {
reg = <0x20000000 0x10000000>;
};
ahb {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
apb {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
aic: interrupt-controller@fffff000 {
#interrupt-cells = <2>;
compatible = "atmel,at91rm9200-aic";
interrupt-controller;
interrupt-parent;
reg = <0xfffff000 0x200>;
};
pit: timer@fffffe30 {
compatible = "atmel,at91sam9260-pit";
reg = <0xfffffe30 0xf>;
interrupts = <1 4>;
};
tcb0: timer@f8008000 {
compatible = "atmel,at91sam9x5-tcb";
reg = <0xf8008000 0x100>;
interrupts = <17 4>;
};
tcb1: timer@f800c000 {
compatible = "atmel,at91sam9x5-tcb";
reg = <0xf800c000 0x100>;
interrupts = <17 4>;
};
dma0: dma-controller@ffffec00 {
compatible = "atmel,at91sam9g45-dma";
reg = <0xffffec00 0x200>;
interrupts = <20 4>;
};
dma1: dma-controller@ffffee00 {
compatible = "atmel,at91sam9g45-dma";
reg = <0xffffee00 0x200>;
interrupts = <21 4>;
};
pioA: gpio@fffff400 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x100>;
interrupts = <2 4>;
#gpio-cells = <2>;
gpio-controller;
};
pioB: gpio@fffff600 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff600 0x100>;
interrupts = <2 4>;
#gpio-cells = <2>;
gpio-controller;
};
pioC: gpio@fffff800 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff800 0x100>;
interrupts = <3 4>;
#gpio-cells = <2>;
gpio-controller;
};
pioD: gpio@fffffa00 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffffa00 0x100>;
interrupts = <3 4>;
#gpio-cells = <2>;
gpio-controller;
};
dbgu: serial@fffff200 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffff200 0x200>;
interrupts = <1 4>;
status = "disabled";
};
usart0: serial@f801c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf801c000 0x200>;
interrupts = <5 4>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
};
usart1: serial@f8020000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8020000 0x200>;
interrupts = <6 4>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
};
usart2: serial@f8024000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8024000 0x200>;
interrupts = <7 4>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
};
macb0: ethernet@f802c000 {
compatible = "cdns,at32ap7000-macb", "cdns,macb";
reg = <0xf802c000 0x100>;
interrupts = <24 4>;
status = "disabled";
};
macb1: ethernet@f8030000 {
compatible = "cdns,at32ap7000-macb", "cdns,macb";
reg = <0xf8030000 0x100>;
interrupts = <27 4>;
status = "disabled";
};
};
};
};
/*
* at91sam9x5cm.dtsi - Device Tree Include file for AT91SAM9x5 CPU Module
*
* Copyright (C) 2012 Atmel,
* 2012 Nicolas Ferre <nicolas.ferre@atmel.com>
*
* Licensed under GPLv2 or later.
*/
/ {
memory@20000000 {
reg = <0x20000000 0x8000000>;
};
};
...@@ -26,6 +26,7 @@ ...@@ -26,6 +26,7 @@
#include <linux/irq.h> #include <linux/irq.h>
#include <linux/io.h> #include <linux/io.h>
#include <asm/sched_clock.h>
#include <asm/hardware/arm_timer.h> #include <asm/hardware/arm_timer.h>
static long __init sp804_get_clock_rate(const char *name) static long __init sp804_get_clock_rate(const char *name)
...@@ -67,7 +68,16 @@ static long __init sp804_get_clock_rate(const char *name) ...@@ -67,7 +68,16 @@ static long __init sp804_get_clock_rate(const char *name)
return rate; return rate;
} }
void __init sp804_clocksource_init(void __iomem *base, const char *name) static void __iomem *sched_clock_base;
static u32 sp804_read(void)
{
return ~readl_relaxed(sched_clock_base + TIMER_VALUE);
}
void __init __sp804_clocksource_and_sched_clock_init(void __iomem *base,
const char *name,
int use_sched_clock)
{ {
long rate = sp804_get_clock_rate(name); long rate = sp804_get_clock_rate(name);
...@@ -83,6 +93,11 @@ void __init sp804_clocksource_init(void __iomem *base, const char *name) ...@@ -83,6 +93,11 @@ void __init sp804_clocksource_init(void __iomem *base, const char *name)
clocksource_mmio_init(base + TIMER_VALUE, name, clocksource_mmio_init(base + TIMER_VALUE, name,
rate, 200, 32, clocksource_mmio_readl_down); rate, 200, 32, clocksource_mmio_readl_down);
if (use_sched_clock) {
sched_clock_base = base;
setup_sched_clock(sp804_read, 32, rate);
}
} }
......
...@@ -5,6 +5,7 @@ CONFIG_SYSVIPC=y ...@@ -5,6 +5,7 @@ CONFIG_SYSVIPC=y
CONFIG_LOG_BUF_SHIFT=18 CONFIG_LOG_BUF_SHIFT=18
CONFIG_CGROUPS=y CONFIG_CGROUPS=y
CONFIG_RELAY=y CONFIG_RELAY=y
CONFIG_BLK_DEV_INITRD=y
CONFIG_EXPERT=y CONFIG_EXPERT=y
# CONFIG_SLUB_DEBUG is not set # CONFIG_SLUB_DEBUG is not set
# CONFIG_COMPAT_BRK is not set # CONFIG_COMPAT_BRK is not set
...@@ -12,7 +13,6 @@ CONFIG_MODULES=y ...@@ -12,7 +13,6 @@ CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y CONFIG_MODULE_UNLOAD=y
CONFIG_MODVERSIONS=y CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_MODULE_SRCVERSION_ALL=y
# CONFIG_LBDAF is not set
# CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_BSG is not set
CONFIG_ARCH_MXC=y CONFIG_ARCH_MXC=y
CONFIG_MACH_MX31LILLY=y CONFIG_MACH_MX31LILLY=y
...@@ -26,7 +26,6 @@ CONFIG_MACH_ARMADILLO5X0=y ...@@ -26,7 +26,6 @@ CONFIG_MACH_ARMADILLO5X0=y
CONFIG_MACH_KZM_ARM11_01=y CONFIG_MACH_KZM_ARM11_01=y
CONFIG_MACH_PCM043=y CONFIG_MACH_PCM043=y
CONFIG_MACH_MX35_3DS=y CONFIG_MACH_MX35_3DS=y
CONFIG_MACH_EUKREA_CPUIMX35=y
CONFIG_MACH_VPR200=y CONFIG_MACH_VPR200=y
CONFIG_MACH_IMX51_DT=y CONFIG_MACH_IMX51_DT=y
CONFIG_MACH_MX51_3DS=y CONFIG_MACH_MX51_3DS=y
...@@ -83,7 +82,6 @@ CONFIG_NETDEVICES=y ...@@ -83,7 +82,6 @@ CONFIG_NETDEVICES=y
# CONFIG_NET_VENDOR_BROADCOM is not set # CONFIG_NET_VENDOR_BROADCOM is not set
# CONFIG_NET_VENDOR_CHELSIO is not set # CONFIG_NET_VENDOR_CHELSIO is not set
# CONFIG_NET_VENDOR_FARADAY is not set # CONFIG_NET_VENDOR_FARADAY is not set
CONFIG_FEC=y
# CONFIG_NET_VENDOR_INTEL is not set # CONFIG_NET_VENDOR_INTEL is not set
# CONFIG_NET_VENDOR_MARVELL is not set # CONFIG_NET_VENDOR_MARVELL is not set
# CONFIG_NET_VENDOR_MICREL is not set # CONFIG_NET_VENDOR_MICREL is not set
...@@ -126,6 +124,7 @@ CONFIG_WATCHDOG=y ...@@ -126,6 +124,7 @@ CONFIG_WATCHDOG=y
CONFIG_IMX2_WDT=y CONFIG_IMX2_WDT=y
CONFIG_MFD_MC13XXX=y CONFIG_MFD_MC13XXX=y
CONFIG_REGULATOR=y CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
CONFIG_REGULATOR_MC13892=y CONFIG_REGULATOR_MC13892=y
CONFIG_USB=y CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_HCD=y
......
...@@ -77,10 +77,10 @@ CONFIG_DEVPTS_MULTIPLE_INSTANCES=y ...@@ -77,10 +77,10 @@ CONFIG_DEVPTS_MULTIPLE_INSTANCES=y
CONFIG_SERIAL_AMBA_PL011=y CONFIG_SERIAL_AMBA_PL011=y
CONFIG_SERIAL_AMBA_PL011_CONSOLE=y CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
# CONFIG_HW_RANDOM is not set # CONFIG_HW_RANDOM is not set
CONFIG_I2C=m CONFIG_I2C=y
# CONFIG_I2C_COMPAT is not set # CONFIG_I2C_COMPAT is not set
CONFIG_I2C_CHARDEV=m CONFIG_I2C_CHARDEV=y
CONFIG_I2C_MXS=m CONFIG_I2C_MXS=y
CONFIG_SPI=y CONFIG_SPI=y
CONFIG_SPI_GPIO=m CONFIG_SPI_GPIO=m
CONFIG_DEBUG_GPIO=y CONFIG_DEBUG_GPIO=y
...@@ -90,6 +90,20 @@ CONFIG_GPIO_SYSFS=y ...@@ -90,6 +90,20 @@ CONFIG_GPIO_SYSFS=y
CONFIG_DISPLAY_SUPPORT=m CONFIG_DISPLAY_SUPPORT=m
# CONFIG_HID_SUPPORT is not set # CONFIG_HID_SUPPORT is not set
# CONFIG_USB_SUPPORT is not set # CONFIG_USB_SUPPORT is not set
CONFIG_SOUND=y
CONFIG_SND=y
CONFIG_SND_TIMER=y
CONFIG_SND_PCM=y
CONFIG_SND_JACK=y
CONFIG_SND_DRIVERS=y
CONFIG_SND_ARM=y
CONFIG_SND_SOC=y
CONFIG_SND_MXS_SOC=y
CONFIG_SND_SOC_MXS_SGTL5000=y
CONFIG_SND_SOC_I2C_AND_SPI=y
CONFIG_SND_SOC_SGTL5000=y
CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
CONFIG_MMC=y CONFIG_MMC=y
CONFIG_MMC_MXS=y CONFIG_MMC_MXS=y
CONFIG_RTC_CLASS=y CONFIG_RTC_CLASS=y
......
void sp804_clocksource_init(void __iomem *, const char *); void __sp804_clocksource_and_sched_clock_init(void __iomem *,
const char *, int);
static inline void sp804_clocksource_init(void __iomem *base, const char *name)
{
__sp804_clocksource_and_sched_clock_init(base, name, 0);
}
static inline void sp804_clocksource_and_sched_clock_init(void __iomem *base,
const char *name)
{
__sp804_clocksource_and_sched_clock_init(base, name, 1);
}
void sp804_clockevents_init(void __iomem *, unsigned int, const char *); void sp804_clockevents_init(void __iomem *, unsigned int, const char *);
...@@ -102,6 +102,15 @@ config ARCH_AT91SAM9G45 ...@@ -102,6 +102,15 @@ config ARCH_AT91SAM9G45
select HAVE_AT91_DBGU1 select HAVE_AT91_DBGU1
select AT91_SAM9G45_RESET select AT91_SAM9G45_RESET
config ARCH_AT91SAM9X5
bool "AT91SAM9x5 family"
select CPU_ARM926T
select GENERIC_CLOCKEVENTS
select HAVE_FB_ATMEL
select HAVE_NET_MACB
select HAVE_AT91_DBGU0
select AT91_SAM9G45_RESET
config ARCH_AT91X40 config ARCH_AT91X40
bool "AT91x40" bool "AT91x40"
select ARCH_USES_GETTIMEOFFSET select ARCH_USES_GETTIMEOFFSET
......
...@@ -20,6 +20,7 @@ obj-$(CONFIG_ARCH_AT91SAM9263) += at91sam9263.o at91sam926x_time.o at91sam9263_d ...@@ -20,6 +20,7 @@ obj-$(CONFIG_ARCH_AT91SAM9263) += at91sam9263.o at91sam926x_time.o at91sam9263_d
obj-$(CONFIG_ARCH_AT91SAM9RL) += at91sam9rl.o at91sam926x_time.o at91sam9rl_devices.o sam9_smc.o obj-$(CONFIG_ARCH_AT91SAM9RL) += at91sam9rl.o at91sam926x_time.o at91sam9rl_devices.o sam9_smc.o
obj-$(CONFIG_ARCH_AT91SAM9G20) += at91sam9260.o at91sam926x_time.o at91sam9260_devices.o sam9_smc.o obj-$(CONFIG_ARCH_AT91SAM9G20) += at91sam9260.o at91sam926x_time.o at91sam9260_devices.o sam9_smc.o
obj-$(CONFIG_ARCH_AT91SAM9G45) += at91sam9g45.o at91sam926x_time.o at91sam9g45_devices.o sam9_smc.o obj-$(CONFIG_ARCH_AT91SAM9G45) += at91sam9g45.o at91sam926x_time.o at91sam9g45_devices.o sam9_smc.o
obj-$(CONFIG_ARCH_AT91SAM9X5) += at91sam9x5.o at91sam926x_time.o
obj-$(CONFIG_ARCH_AT91X40) += at91x40.o at91x40_time.o obj-$(CONFIG_ARCH_AT91X40) += at91x40.o at91x40_time.o
# AT91RM9200 board-specific support # AT91RM9200 board-specific support
......
/*
* Chip-specific setup code for the AT91SAM9x5 family
*
* Copyright (C) 2010-2012 Atmel Corporation.
*
* Licensed under GPLv2 or later.
*/
#include <linux/module.h>
#include <linux/dma-mapping.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <mach/at91sam9x5.h>
#include <mach/at91_pmc.h>
#include <mach/cpu.h>
#include <mach/board.h>
#include "soc.h"
#include "generic.h"
#include "clock.h"
#include "sam9_smc.h"
/* --------------------------------------------------------------------
* Clocks
* -------------------------------------------------------------------- */
/*
* The peripheral clocks.
*/
static struct clk pioAB_clk = {
.name = "pioAB_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_PIOAB,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk pioCD_clk = {
.name = "pioCD_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_PIOCD,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk smd_clk = {
.name = "smd_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_SMD,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk usart0_clk = {
.name = "usart0_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_USART0,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk usart1_clk = {
.name = "usart1_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_USART1,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk usart2_clk = {
.name = "usart2_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_USART2,
.type = CLK_TYPE_PERIPHERAL,
};
/* USART3 clock - Only for sam9g25/sam9x25 */
static struct clk usart3_clk = {
.name = "usart3_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_USART3,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk twi0_clk = {
.name = "twi0_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_TWI0,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk twi1_clk = {
.name = "twi1_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_TWI1,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk twi2_clk = {
.name = "twi2_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_TWI2,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk mmc0_clk = {
.name = "mci0_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_MCI0,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk spi0_clk = {
.name = "spi0_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_SPI0,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk spi1_clk = {
.name = "spi1_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_SPI1,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk uart0_clk = {
.name = "uart0_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_UART0,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk uart1_clk = {
.name = "uart1_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_UART1,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk tcb0_clk = {
.name = "tcb0_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_TCB,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk pwm_clk = {
.name = "pwm_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_PWM,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk adc_clk = {
.name = "adc_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_ADC,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk dma0_clk = {
.name = "dma0_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_DMA0,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk dma1_clk = {
.name = "dma1_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_DMA1,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk uhphs_clk = {
.name = "uhphs_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_UHPHS,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk udphs_clk = {
.name = "udphs_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_UDPHS,
.type = CLK_TYPE_PERIPHERAL,
};
/* emac0 clock - Only for sam9g25/sam9x25/sam9g35/sam9x35 */
static struct clk macb0_clk = {
.name = "pclk",
.pmc_mask = 1 << AT91SAM9X5_ID_EMAC0,
.type = CLK_TYPE_PERIPHERAL,
};
/* lcd clock - Only for sam9g15/sam9g35/sam9x35 */
static struct clk lcdc_clk = {
.name = "lcdc_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_LCDC,
.type = CLK_TYPE_PERIPHERAL,
};
/* isi clock - Only for sam9g25 */
static struct clk isi_clk = {
.name = "isi_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_ISI,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk mmc1_clk = {
.name = "mci1_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_MCI1,
.type = CLK_TYPE_PERIPHERAL,
};
/* emac1 clock - Only for sam9x25 */
static struct clk macb1_clk = {
.name = "pclk",
.pmc_mask = 1 << AT91SAM9X5_ID_EMAC1,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk ssc_clk = {
.name = "ssc_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_SSC,
.type = CLK_TYPE_PERIPHERAL,
};
/* can0 clock - Only for sam9x35 */
static struct clk can0_clk = {
.name = "can0_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_CAN0,
.type = CLK_TYPE_PERIPHERAL,
};
/* can1 clock - Only for sam9x35 */
static struct clk can1_clk = {
.name = "can1_clk",
.pmc_mask = 1 << AT91SAM9X5_ID_CAN1,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk *periph_clocks[] __initdata = {
&pioAB_clk,
&pioCD_clk,
&smd_clk,
&usart0_clk,
&usart1_clk,
&usart2_clk,
&twi0_clk,
&twi1_clk,
&twi2_clk,
&mmc0_clk,
&spi0_clk,
&spi1_clk,
&uart0_clk,
&uart1_clk,
&tcb0_clk,
&pwm_clk,
&adc_clk,
&dma0_clk,
&dma1_clk,
&uhphs_clk,
&udphs_clk,
&mmc1_clk,
&ssc_clk,
// irq0
};
static struct clk_lookup periph_clocks_lookups[] = {
/* lookup table for DT entries */
CLKDEV_CON_DEV_ID("usart", "fffff200.serial", &mck),
CLKDEV_CON_DEV_ID("usart", "f801c000.serial", &usart0_clk),
CLKDEV_CON_DEV_ID("usart", "f8020000.serial", &usart1_clk),
CLKDEV_CON_DEV_ID("usart", "f8024000.serial", &usart2_clk),
CLKDEV_CON_DEV_ID("usart", "f8028000.serial", &usart3_clk),
CLKDEV_CON_DEV_ID("t0_clk", "f8008000.timer", &tcb0_clk),
CLKDEV_CON_DEV_ID("t0_clk", "f800c000.timer", &tcb0_clk),
CLKDEV_CON_ID("pioA", &pioAB_clk),
CLKDEV_CON_ID("pioB", &pioAB_clk),
CLKDEV_CON_ID("pioC", &pioCD_clk),
CLKDEV_CON_ID("pioD", &pioCD_clk),
/* additional fake clock for macb_hclk */
CLKDEV_CON_DEV_ID("hclk", "f802c000.ethernet", &macb0_clk),
CLKDEV_CON_DEV_ID("hclk", "f8030000.ethernet", &macb1_clk),
};
/*
* The two programmable clocks.
* You must configure pin multiplexing to bring these signals out.
*/
static struct clk pck0 = {
.name = "pck0",
.pmc_mask = AT91_PMC_PCK0,
.type = CLK_TYPE_PROGRAMMABLE,
.id = 0,
};
static struct clk pck1 = {
.name = "pck1",
.pmc_mask = AT91_PMC_PCK1,
.type = CLK_TYPE_PROGRAMMABLE,
.id = 1,
};
static void __init at91sam9x5_register_clocks(void)
{
int i;
for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
clk_register(periph_clocks[i]);
clkdev_add_table(periph_clocks_lookups,
ARRAY_SIZE(periph_clocks_lookups));
if (cpu_is_at91sam9g25()
|| cpu_is_at91sam9x25())
clk_register(&usart3_clk);
if (cpu_is_at91sam9g25()
|| cpu_is_at91sam9x25()
|| cpu_is_at91sam9g35()
|| cpu_is_at91sam9x35())
clk_register(&macb0_clk);
if (cpu_is_at91sam9g15()
|| cpu_is_at91sam9g35()
|| cpu_is_at91sam9x35())
clk_register(&lcdc_clk);
if (cpu_is_at91sam9g25())
clk_register(&isi_clk);
if (cpu_is_at91sam9x25())
clk_register(&macb1_clk);
if (cpu_is_at91sam9x25()
|| cpu_is_at91sam9x35()) {
clk_register(&can0_clk);
clk_register(&can1_clk);
}
clk_register(&pck0);
clk_register(&pck1);
}
/* --------------------------------------------------------------------
* AT91SAM9x5 processor initialization
* -------------------------------------------------------------------- */
static void __init at91sam9x5_map_io(void)
{
at91_init_sram(0, AT91SAM9X5_SRAM_BASE, AT91SAM9X5_SRAM_SIZE);
}
static void __init at91sam9x5_ioremap_registers(void)
{
if (of_at91sam926x_pit_init() < 0)
panic("Impossible to find PIT\n");
}
void __init at91sam9x5_initialize(void)
{
arm_pm_restart = at91sam9g45_restart;
at91_extern_irq = (1 << AT91SAM9X5_ID_IRQ0);
/* Register GPIO subsystem (using DT) */
at91_gpio_init(NULL, 0);
}
/* --------------------------------------------------------------------
* AT91SAM9x5 devices (temporary before modification of code)
* -------------------------------------------------------------------- */
void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
void __init at91_set_serial_console(unsigned portnr) {}
struct platform_device *atmel_default_console_device = NULL;
void __init at91_add_device_nand(struct atmel_nand_data *data) {}
/* --------------------------------------------------------------------
* Interrupt initialization
* -------------------------------------------------------------------- */
/*
* The default interrupt priority levels (0 = lowest, 7 = highest).
*/
static unsigned int at91sam9x5_default_irq_priority[NR_AIC_IRQS] __initdata = {
7, /* Advanced Interrupt Controller (FIQ) */
7, /* System Peripherals */
1, /* Parallel IO Controller A and B */
1, /* Parallel IO Controller C and D */
4, /* Soft Modem */
5, /* USART 0 */
5, /* USART 1 */
5, /* USART 2 */
5, /* USART 3 */
6, /* Two-Wire Interface 0 */
6, /* Two-Wire Interface 1 */
6, /* Two-Wire Interface 2 */
0, /* Multimedia Card Interface 0 */
5, /* Serial Peripheral Interface 0 */
5, /* Serial Peripheral Interface 1 */
5, /* UART 0 */
5, /* UART 1 */
0, /* Timer Counter 0, 1, 2, 3, 4 and 5 */
0, /* Pulse Width Modulation Controller */
0, /* ADC Controller */
0, /* DMA Controller 0 */
0, /* DMA Controller 1 */
2, /* USB Host High Speed port */
2, /* USB Device High speed port */
3, /* Ethernet MAC 0 */
3, /* LDC Controller or Image Sensor Interface */
0, /* Multimedia Card Interface 1 */
3, /* Ethernet MAC 1 */
4, /* Synchronous Serial Interface */
4, /* CAN Controller 0 */
4, /* CAN Controller 1 */
0, /* Advanced Interrupt Controller (IRQ0) */
};
struct at91_init_soc __initdata at91sam9x5_soc = {
.map_io = at91sam9x5_map_io,
.default_irq_priority = at91sam9x5_default_irq_priority,
.ioremap_registers = at91sam9x5_ioremap_registers,
.register_clocks = at91sam9x5_register_clocks,
.init = at91sam9x5_initialize,
};
...@@ -109,6 +109,7 @@ static void __init at91_dt_device_init(void) ...@@ -109,6 +109,7 @@ static void __init at91_dt_device_init(void)
static const char *at91_dt_board_compat[] __initdata = { static const char *at91_dt_board_compat[] __initdata = {
"atmel,at91sam9m10g45ek", "atmel,at91sam9m10g45ek",
"atmel,at91sam9x5ek",
"calao,usb-a9g20", "calao,usb-a9g20",
NULL NULL
}; };
......
...@@ -48,24 +48,37 @@ ...@@ -48,24 +48,37 @@
* Chips have some kind of clocks : group them by functionality * Chips have some kind of clocks : group them by functionality
*/ */
#define cpu_has_utmi() ( cpu_is_at91sam9rl() \ #define cpu_has_utmi() ( cpu_is_at91sam9rl() \
|| cpu_is_at91sam9g45()) || cpu_is_at91sam9g45() \
|| cpu_is_at91sam9x5())
#define cpu_has_800M_plla() ( cpu_is_at91sam9g20() \ #define cpu_has_800M_plla() ( cpu_is_at91sam9g20() \
|| cpu_is_at91sam9g45()) || cpu_is_at91sam9g45() \
|| cpu_is_at91sam9x5())
#define cpu_has_300M_plla() (cpu_is_at91sam9g10()) #define cpu_has_300M_plla() (cpu_is_at91sam9g10())
#define cpu_has_pllb() (!(cpu_is_at91sam9rl() \ #define cpu_has_pllb() (!(cpu_is_at91sam9rl() \
|| cpu_is_at91sam9g45())) || cpu_is_at91sam9g45() \
|| cpu_is_at91sam9x5()))
#define cpu_has_upll() (cpu_is_at91sam9g45()) #define cpu_has_upll() (cpu_is_at91sam9g45() \
|| cpu_is_at91sam9x5())
/* USB host HS & FS */ /* USB host HS & FS */
#define cpu_has_uhp() (!cpu_is_at91sam9rl()) #define cpu_has_uhp() (!cpu_is_at91sam9rl())
/* USB device FS only */ /* USB device FS only */
#define cpu_has_udpfs() (!(cpu_is_at91sam9rl() \ #define cpu_has_udpfs() (!(cpu_is_at91sam9rl() \
|| cpu_is_at91sam9g45())) || cpu_is_at91sam9g45() \
|| cpu_is_at91sam9x5()))
#define cpu_has_plladiv2() (cpu_is_at91sam9g45() \
|| cpu_is_at91sam9x5())
#define cpu_has_mdiv3() (cpu_is_at91sam9g45() \
|| cpu_is_at91sam9x5())
#define cpu_has_alt_prescaler() (cpu_is_at91sam9x5())
static LIST_HEAD(clocks); static LIST_HEAD(clocks);
static DEFINE_SPINLOCK(clk_lock); static DEFINE_SPINLOCK(clk_lock);
...@@ -138,13 +151,6 @@ static void pmc_uckr_mode(struct clk *clk, int is_on) ...@@ -138,13 +151,6 @@ static void pmc_uckr_mode(struct clk *clk, int is_on)
{ {
unsigned int uckr = at91_sys_read(AT91_CKGR_UCKR); unsigned int uckr = at91_sys_read(AT91_CKGR_UCKR);
if (cpu_is_at91sam9g45()) {
if (is_on)
uckr |= AT91_PMC_BIASEN;
else
uckr &= ~AT91_PMC_BIASEN;
}
if (is_on) { if (is_on) {
is_on = AT91_PMC_LOCKU; is_on = AT91_PMC_LOCKU;
at91_sys_write(AT91_CKGR_UCKR, uckr | clk->pmc_mask); at91_sys_write(AT91_CKGR_UCKR, uckr | clk->pmc_mask);
...@@ -209,11 +215,24 @@ static struct clk __init *at91_css_to_clk(unsigned long css) ...@@ -209,11 +215,24 @@ static struct clk __init *at91_css_to_clk(unsigned long css)
return &utmi_clk; return &utmi_clk;
else if (cpu_has_pllb()) else if (cpu_has_pllb())
return &pllb; return &pllb;
break;
/* alternate PMC: can use master clock */
case AT91_PMC_CSS_MASTER:
return &mck;
} }
return NULL; return NULL;
} }
static int pmc_prescaler_divider(u32 reg)
{
if (cpu_has_alt_prescaler()) {
return 1 << ((reg & AT91_PMC_ALT_PRES) >> PMC_ALT_PRES_OFFSET);
} else {
return 1 << ((reg & AT91_PMC_PRES) >> PMC_PRES_OFFSET);
}
}
static void __clk_enable(struct clk *clk) static void __clk_enable(struct clk *clk)
{ {
if (clk->parent) if (clk->parent)
...@@ -315,12 +334,22 @@ int clk_set_rate(struct clk *clk, unsigned long rate) ...@@ -315,12 +334,22 @@ int clk_set_rate(struct clk *clk, unsigned long rate)
{ {
unsigned long flags; unsigned long flags;
unsigned prescale; unsigned prescale;
unsigned long prescale_offset, css_mask;
unsigned long actual; unsigned long actual;
if (!clk_is_programmable(clk)) if (!clk_is_programmable(clk))
return -EINVAL; return -EINVAL;
if (clk->users) if (clk->users)
return -EBUSY; return -EBUSY;
if (cpu_has_alt_prescaler()) {
prescale_offset = PMC_ALT_PRES_OFFSET;
css_mask = AT91_PMC_ALT_PCKR_CSS;
} else {
prescale_offset = PMC_PRES_OFFSET;
css_mask = AT91_PMC_CSS;
}
spin_lock_irqsave(&clk_lock, flags); spin_lock_irqsave(&clk_lock, flags);
actual = clk->parent->rate_hz; actual = clk->parent->rate_hz;
...@@ -329,8 +358,8 @@ int clk_set_rate(struct clk *clk, unsigned long rate) ...@@ -329,8 +358,8 @@ int clk_set_rate(struct clk *clk, unsigned long rate)
u32 pckr; u32 pckr;
pckr = at91_sys_read(AT91_PMC_PCKR(clk->id)); pckr = at91_sys_read(AT91_PMC_PCKR(clk->id));
pckr &= AT91_PMC_CSS; /* clock selection */ pckr &= css_mask; /* keep clock selection */
pckr |= prescale << 2; pckr |= prescale << prescale_offset;
at91_sys_write(AT91_PMC_PCKR(clk->id), pckr); at91_sys_write(AT91_PMC_PCKR(clk->id), pckr);
clk->rate_hz = actual; clk->rate_hz = actual;
break; break;
...@@ -377,11 +406,17 @@ static void __init init_programmable_clock(struct clk *clk) ...@@ -377,11 +406,17 @@ static void __init init_programmable_clock(struct clk *clk)
{ {
struct clk *parent; struct clk *parent;
u32 pckr; u32 pckr;
unsigned int css_mask;
if (cpu_has_alt_prescaler())
css_mask = AT91_PMC_ALT_PCKR_CSS;
else
css_mask = AT91_PMC_CSS;
pckr = at91_sys_read(AT91_PMC_PCKR(clk->id)); pckr = at91_sys_read(AT91_PMC_PCKR(clk->id));
parent = at91_css_to_clk(pckr & AT91_PMC_CSS); parent = at91_css_to_clk(pckr & css_mask);
clk->parent = parent; clk->parent = parent;
clk->rate_hz = parent->rate_hz / (1 << ((pckr & AT91_PMC_PRES) >> 2)); clk->rate_hz = parent->rate_hz / pmc_prescaler_divider(pckr);
} }
#endif /* CONFIG_AT91_PROGRAMMABLE_CLOCKS */ #endif /* CONFIG_AT91_PROGRAMMABLE_CLOCKS */
...@@ -663,7 +698,7 @@ int __init at91_clock_init(unsigned long main_clock) ...@@ -663,7 +698,7 @@ int __init at91_clock_init(unsigned long main_clock)
if (pll_overclock) if (pll_overclock)
pr_info("Clocks: PLLA overclocked, %ld MHz\n", plla.rate_hz / 1000000); pr_info("Clocks: PLLA overclocked, %ld MHz\n", plla.rate_hz / 1000000);
if (cpu_is_at91sam9g45()) { if (cpu_has_plladiv2()) {
mckr = at91_sys_read(AT91_PMC_MCKR); mckr = at91_sys_read(AT91_PMC_MCKR);
plla.rate_hz /= (1 << ((mckr & AT91_PMC_PLLADIV2) >> 12)); /* plla divisor by 2 */ plla.rate_hz /= (1 << ((mckr & AT91_PMC_PLLADIV2) >> 12)); /* plla divisor by 2 */
} }
...@@ -685,6 +720,10 @@ int __init at91_clock_init(unsigned long main_clock) ...@@ -685,6 +720,10 @@ int __init at91_clock_init(unsigned long main_clock)
* (obtain the USB High Speed 480 MHz when input is 12 MHz) * (obtain the USB High Speed 480 MHz when input is 12 MHz)
*/ */
utmi_clk.rate_hz = 40 * utmi_clk.parent->rate_hz; utmi_clk.rate_hz = 40 * utmi_clk.parent->rate_hz;
/* UTMI bias and PLL are managed at the same time */
if (cpu_has_upll())
utmi_clk.pmc_mask |= AT91_PMC_BIASEN;
} }
/* /*
...@@ -703,7 +742,7 @@ int __init at91_clock_init(unsigned long main_clock) ...@@ -703,7 +742,7 @@ int __init at91_clock_init(unsigned long main_clock)
mckr = at91_sys_read(AT91_PMC_MCKR); mckr = at91_sys_read(AT91_PMC_MCKR);
mck.parent = at91_css_to_clk(mckr & AT91_PMC_CSS); mck.parent = at91_css_to_clk(mckr & AT91_PMC_CSS);
freq = mck.parent->rate_hz; freq = mck.parent->rate_hz;
freq /= (1 << ((mckr & AT91_PMC_PRES) >> 2)); /* prescale */ freq /= pmc_prescaler_divider(mckr); /* prescale */
if (cpu_is_at91rm9200()) { if (cpu_is_at91rm9200()) {
mck.rate_hz = freq / (1 + ((mckr & AT91_PMC_MDIV) >> 8)); /* mdiv */ mck.rate_hz = freq / (1 + ((mckr & AT91_PMC_MDIV) >> 8)); /* mdiv */
} else if (cpu_is_at91sam9g20()) { } else if (cpu_is_at91sam9g20()) {
...@@ -711,13 +750,19 @@ int __init at91_clock_init(unsigned long main_clock) ...@@ -711,13 +750,19 @@ int __init at91_clock_init(unsigned long main_clock)
freq / ((mckr & AT91_PMC_MDIV) >> 7) : freq; /* mdiv ; (x >> 7) = ((x >> 8) * 2) */ freq / ((mckr & AT91_PMC_MDIV) >> 7) : freq; /* mdiv ; (x >> 7) = ((x >> 8) * 2) */
if (mckr & AT91_PMC_PDIV) if (mckr & AT91_PMC_PDIV)
freq /= 2; /* processor clock division */ freq /= 2; /* processor clock division */
} else if (cpu_is_at91sam9g45()) { } else if (cpu_has_mdiv3()) {
mck.rate_hz = (mckr & AT91_PMC_MDIV) == AT91SAM9_PMC_MDIV_3 ? mck.rate_hz = (mckr & AT91_PMC_MDIV) == AT91SAM9_PMC_MDIV_3 ?
freq / 3 : freq / (1 << ((mckr & AT91_PMC_MDIV) >> 8)); /* mdiv */ freq / 3 : freq / (1 << ((mckr & AT91_PMC_MDIV) >> 8)); /* mdiv */
} else { } else {
mck.rate_hz = freq / (1 << ((mckr & AT91_PMC_MDIV) >> 8)); /* mdiv */ mck.rate_hz = freq / (1 << ((mckr & AT91_PMC_MDIV) >> 8)); /* mdiv */
} }
if (cpu_has_alt_prescaler()) {
/* Programmable clocks can use MCK */
mck.type |= CLK_TYPE_PRIMARY;
mck.id = 4;
}
/* Register the PMC's standard clocks */ /* Register the PMC's standard clocks */
for (i = 0; i < ARRAY_SIZE(standard_pmc_clocks); i++) for (i = 0; i < ARRAY_SIZE(standard_pmc_clocks); i++)
at91_clk_add(standard_pmc_clocks[i]); at91_clk_add(standard_pmc_clocks[i]);
......
...@@ -46,8 +46,12 @@ ...@@ -46,8 +46,12 @@
#define AT91_CKGR_MOR (AT91_PMC + 0x20) /* Main Oscillator Register [not on SAM9RL] */ #define AT91_CKGR_MOR (AT91_PMC + 0x20) /* Main Oscillator Register [not on SAM9RL] */
#define AT91_PMC_MOSCEN (1 << 0) /* Main Oscillator Enable */ #define AT91_PMC_MOSCEN (1 << 0) /* Main Oscillator Enable */
#define AT91_PMC_OSCBYPASS (1 << 1) /* Oscillator Bypass [SAM9x] */ #define AT91_PMC_OSCBYPASS (1 << 1) /* Oscillator Bypass */
#define AT91_PMC_MOSCRCEN (1 << 3) /* Main On-Chip RC Oscillator Enable [some SAM9] */
#define AT91_PMC_OSCOUNT (0xff << 8) /* Main Oscillator Start-up Time */ #define AT91_PMC_OSCOUNT (0xff << 8) /* Main Oscillator Start-up Time */
#define AT91_PMC_KEY (0x37 << 16) /* MOR Writing Key */
#define AT91_PMC_MOSCSEL (1 << 24) /* Main Oscillator Selection [some SAM9] */
#define AT91_PMC_CFDEN (1 << 25) /* Clock Failure Detector Enable [some SAM9] */
#define AT91_CKGR_MCFR (AT91_PMC + 0x24) /* Main Clock Frequency Register */ #define AT91_CKGR_MCFR (AT91_PMC + 0x24) /* Main Clock Frequency Register */
#define AT91_PMC_MAINF (0xffff << 0) /* Main Clock Frequency */ #define AT91_PMC_MAINF (0xffff << 0) /* Main Clock Frequency */
...@@ -72,14 +76,24 @@ ...@@ -72,14 +76,24 @@
#define AT91_PMC_CSS_PLLA (2 << 0) #define AT91_PMC_CSS_PLLA (2 << 0)
#define AT91_PMC_CSS_PLLB (3 << 0) #define AT91_PMC_CSS_PLLB (3 << 0)
#define AT91_PMC_CSS_UPLL (3 << 0) /* [some SAM9 only] */ #define AT91_PMC_CSS_UPLL (3 << 0) /* [some SAM9 only] */
#define AT91_PMC_PRES (7 << 2) /* Master Clock Prescaler */ #define PMC_PRES_OFFSET 2
#define AT91_PMC_PRES_1 (0 << 2) #define AT91_PMC_PRES (7 << PMC_PRES_OFFSET) /* Master Clock Prescaler */
#define AT91_PMC_PRES_2 (1 << 2) #define AT91_PMC_PRES_1 (0 << PMC_PRES_OFFSET)
#define AT91_PMC_PRES_4 (2 << 2) #define AT91_PMC_PRES_2 (1 << PMC_PRES_OFFSET)
#define AT91_PMC_PRES_8 (3 << 2) #define AT91_PMC_PRES_4 (2 << PMC_PRES_OFFSET)
#define AT91_PMC_PRES_16 (4 << 2) #define AT91_PMC_PRES_8 (3 << PMC_PRES_OFFSET)
#define AT91_PMC_PRES_32 (5 << 2) #define AT91_PMC_PRES_16 (4 << PMC_PRES_OFFSET)
#define AT91_PMC_PRES_64 (6 << 2) #define AT91_PMC_PRES_32 (5 << PMC_PRES_OFFSET)
#define AT91_PMC_PRES_64 (6 << PMC_PRES_OFFSET)
#define PMC_ALT_PRES_OFFSET 4
#define AT91_PMC_ALT_PRES (7 << PMC_ALT_PRES_OFFSET) /* Master Clock Prescaler [alternate location] */
#define AT91_PMC_ALT_PRES_1 (0 << PMC_ALT_PRES_OFFSET)
#define AT91_PMC_ALT_PRES_2 (1 << PMC_ALT_PRES_OFFSET)
#define AT91_PMC_ALT_PRES_4 (2 << PMC_ALT_PRES_OFFSET)
#define AT91_PMC_ALT_PRES_8 (3 << PMC_ALT_PRES_OFFSET)
#define AT91_PMC_ALT_PRES_16 (4 << PMC_ALT_PRES_OFFSET)
#define AT91_PMC_ALT_PRES_32 (5 << PMC_ALT_PRES_OFFSET)
#define AT91_PMC_ALT_PRES_64 (6 << PMC_ALT_PRES_OFFSET)
#define AT91_PMC_MDIV (3 << 8) /* Master Clock Division */ #define AT91_PMC_MDIV (3 << 8) /* Master Clock Division */
#define AT91RM9200_PMC_MDIV_1 (0 << 8) /* [AT91RM9200 only] */ #define AT91RM9200_PMC_MDIV_1 (0 << 8) /* [AT91RM9200 only] */
#define AT91RM9200_PMC_MDIV_2 (1 << 8) #define AT91RM9200_PMC_MDIV_2 (1 << 8)
...@@ -103,7 +117,14 @@ ...@@ -103,7 +117,14 @@
#define AT91_PMC_USBS_UPLL (1 << 0) #define AT91_PMC_USBS_UPLL (1 << 0)
#define AT91_PMC_OHCIUSBDIV (0xF << 8) /* Divider for USB OHCI Clock */ #define AT91_PMC_OHCIUSBDIV (0xF << 8) /* Divider for USB OHCI Clock */
#define AT91_PMC_SMD (AT91_PMC + 0x3c) /* Soft Modem Clock Register [some SAM9 only] */
#define AT91_PMC_SMDS (0x1 << 0) /* SMD input clock selection */
#define AT91_PMC_SMD_DIV (0x1f << 8) /* SMD input clock divider */
#define AT91_PMC_SMDDIV(n) (((n) << 8) & AT91_PMC_SMD_DIV)
#define AT91_PMC_PCKR(n) (AT91_PMC + 0x40 + ((n) * 4)) /* Programmable Clock 0-N Registers */ #define AT91_PMC_PCKR(n) (AT91_PMC + 0x40 + ((n) * 4)) /* Programmable Clock 0-N Registers */
#define AT91_PMC_ALT_PCKR_CSS (0x7 << 0) /* Programmable Clock Source Selection [alternate length] */
#define AT91_PMC_CSS_MASTER (4 << 0) /* [some SAM9 only] */
#define AT91_PMC_CSSMCK (0x1 << 8) /* CSS or Master Clock Selection */ #define AT91_PMC_CSSMCK (0x1 << 8) /* CSS or Master Clock Selection */
#define AT91_PMC_CSSMCK_CSS (0 << 8) #define AT91_PMC_CSSMCK_CSS (0 << 8)
#define AT91_PMC_CSSMCK_MCK (1 << 8) #define AT91_PMC_CSSMCK_MCK (1 << 8)
...@@ -120,10 +141,25 @@ ...@@ -120,10 +141,25 @@
#define AT91_PMC_PCK1RDY (1 << 9) /* Programmable Clock 1 */ #define AT91_PMC_PCK1RDY (1 << 9) /* Programmable Clock 1 */
#define AT91_PMC_PCK2RDY (1 << 10) /* Programmable Clock 2 */ #define AT91_PMC_PCK2RDY (1 << 10) /* Programmable Clock 2 */
#define AT91_PMC_PCK3RDY (1 << 11) /* Programmable Clock 3 */ #define AT91_PMC_PCK3RDY (1 << 11) /* Programmable Clock 3 */
#define AT91_PMC_MOSCSELS (1 << 16) /* Main Oscillator Selection [some SAM9] */
#define AT91_PMC_MOSCRCS (1 << 17) /* Main On-Chip RC [some SAM9] */
#define AT91_PMC_CFDEV (1 << 18) /* Clock Failure Detector Event [some SAM9] */
#define AT91_PMC_IMR (AT91_PMC + 0x6c) /* Interrupt Mask Register */ #define AT91_PMC_IMR (AT91_PMC + 0x6c) /* Interrupt Mask Register */
#define AT91_PMC_PROT (AT91_PMC + 0xe4) /* Write Protect Mode Register [some SAM9] */ #define AT91_PMC_PROT (AT91_PMC + 0xe4) /* Write Protect Mode Register [some SAM9] */
#define AT91_PMC_PROTKEY 0x504d4301 /* Activation Code */ #define AT91_PMC_WPEN (0x1 << 0) /* Write Protect Enable */
#define AT91_PMC_WPKEY (0xffffff << 8) /* Write Protect Key */
#define AT91_PMC_PROTKEY (0x504d43 << 8) /* Activation Code */
#define AT91_PMC_WPSR (AT91_PMC + 0xe8) /* Write Protect Status Register [some SAM9] */
#define AT91_PMC_WPVS (0x1 << 0) /* Write Protect Violation Status */
#define AT91_PMC_WPVSRC (0xffff << 8) /* Write Protect Violation Source */
#define AT91_PMC_PCR (AT91_PMC + 0x10c) /* Peripheral Control Register [some SAM9] */
#define AT91_PMC_PCR_PID (0x3f << 0) /* Peripheral ID */
#define AT91_PMC_PCR_CMD (0x1 << 12) /* Command */
#define AT91_PMC_PCR_DIV (0x3 << 16) /* Divisor Value */
#define AT91_PMC_PCRDIV(n) (((n) << 16) & AT91_PMC_PCR_DIV)
#define AT91_PMC_PCR_EN (0x1 << 28) /* Enable */
#endif #endif
/*
* Chip-specific header file for the AT91SAM9x5 family
*
* Copyright (C) 2009-2012 Atmel Corporation.
*
* Common definitions.
* Based on AT91SAM9x5 datasheet.
*
* Licensed under GPLv2 or later.
*/
#ifndef AT91SAM9X5_H
#define AT91SAM9X5_H
/*
* Peripheral identifiers/interrupts.
*/
#define AT91SAM9X5_ID_PIOAB 2 /* Parallel I/O Controller A and B */
#define AT91SAM9X5_ID_PIOCD 3 /* Parallel I/O Controller C and D */
#define AT91SAM9X5_ID_SMD 4 /* SMD Soft Modem (SMD) */
#define AT91SAM9X5_ID_USART0 5 /* USART 0 */
#define AT91SAM9X5_ID_USART1 6 /* USART 1 */
#define AT91SAM9X5_ID_USART2 7 /* USART 2 */
#define AT91SAM9X5_ID_USART3 8 /* USART 3 */
#define AT91SAM9X5_ID_TWI0 9 /* Two-Wire Interface 0 */
#define AT91SAM9X5_ID_TWI1 10 /* Two-Wire Interface 1 */
#define AT91SAM9X5_ID_TWI2 11 /* Two-Wire Interface 2 */
#define AT91SAM9X5_ID_MCI0 12 /* High Speed Multimedia Card Interface 0 */
#define AT91SAM9X5_ID_SPI0 13 /* Serial Peripheral Interface 0 */
#define AT91SAM9X5_ID_SPI1 14 /* Serial Peripheral Interface 1 */
#define AT91SAM9X5_ID_UART0 15 /* UART 0 */
#define AT91SAM9X5_ID_UART1 16 /* UART 1 */
#define AT91SAM9X5_ID_TCB 17 /* Timer Counter 0, 1, 2, 3, 4 and 5 */
#define AT91SAM9X5_ID_PWM 18 /* Pulse Width Modulation Controller */
#define AT91SAM9X5_ID_ADC 19 /* ADC Controller */
#define AT91SAM9X5_ID_DMA0 20 /* DMA Controller 0 */
#define AT91SAM9X5_ID_DMA1 21 /* DMA Controller 1 */
#define AT91SAM9X5_ID_UHPHS 22 /* USB Host High Speed */
#define AT91SAM9X5_ID_UDPHS 23 /* USB Device High Speed */
#define AT91SAM9X5_ID_EMAC0 24 /* Ethernet MAC0 */
#define AT91SAM9X5_ID_LCDC 25 /* LCD Controller */
#define AT91SAM9X5_ID_ISI 25 /* Image Sensor Interface */
#define AT91SAM9X5_ID_MCI1 26 /* High Speed Multimedia Card Interface 1 */
#define AT91SAM9X5_ID_EMAC1 27 /* Ethernet MAC1 */
#define AT91SAM9X5_ID_SSC 28 /* Synchronous Serial Controller */
#define AT91SAM9X5_ID_CAN0 29 /* CAN Controller 0 */
#define AT91SAM9X5_ID_CAN1 30 /* CAN Controller 1 */
#define AT91SAM9X5_ID_IRQ0 31 /* Advanced Interrupt Controller */
/*
* User Peripheral physical base addresses.
*/
#define AT91SAM9X5_BASE_USART0 0xf801c000
#define AT91SAM9X5_BASE_USART1 0xf8020000
#define AT91SAM9X5_BASE_USART2 0xf8024000
/*
* System Peripherals (offset from AT91_BASE_SYS)
*/
#define AT91_DDRSDRC0 (0xffffe800 - AT91_BASE_SYS)
#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
/*
* Base addresses for early serial code (uncompress.h)
*/
#define AT91_DBGU AT91_BASE_DBGU0
#define AT91_USART0 AT91SAM9X5_BASE_USART0
#define AT91_USART1 AT91SAM9X5_BASE_USART1
#define AT91_USART2 AT91SAM9X5_BASE_USART2
/*
* Internal Memory.
*/
#define AT91SAM9X5_SRAM_BASE 0x00300000 /* Internal SRAM base address */
#define AT91SAM9X5_SRAM_SIZE SZ_32K /* Internal SRAM size (32Kb) */
#define AT91SAM9X5_ROM_BASE 0x00400000 /* Internal ROM base address */
#define AT91SAM9X5_ROM_SIZE SZ_64K /* Internal ROM size (64Kb) */
#endif
/*
* Matrix-centric header file for the AT91SAM9x5 family
*
* Copyright (C) 2009-2012 Atmel Corporation.
*
* Only EBI related registers.
* Write Protect register definitions may be useful.
*
* Licensed under GPLv2 or later.
*/
#ifndef AT91SAM9X5_MATRIX_H
#define AT91SAM9X5_MATRIX_H
#define AT91_MATRIX_EBICSA (AT91_MATRIX + 0x120) /* EBI Chip Select Assignment Register */
#define AT91_MATRIX_EBI_CS1A (1 << 1) /* Chip Select 1 Assignment */
#define AT91_MATRIX_EBI_CS1A_SMC (0 << 1)
#define AT91_MATRIX_EBI_CS1A_SDRAMC (1 << 1)
#define AT91_MATRIX_EBI_CS3A (1 << 3) /* Chip Select 3 Assignment */
#define AT91_MATRIX_EBI_CS3A_SMC (0 << 3)
#define AT91_MATRIX_EBI_CS3A_SMC_NANDFLASH (1 << 3)
#define AT91_MATRIX_EBI_DBPUC (1 << 8) /* Data Bus Pull-up Configuration */
#define AT91_MATRIX_EBI_DBPU_ON (0 << 8)
#define AT91_MATRIX_EBI_DBPU_OFF (1 << 8)
#define AT91_MATRIX_EBI_VDDIOMSEL (1 << 16) /* Memory voltage selection */
#define AT91_MATRIX_EBI_VDDIOMSEL_1_8V (0 << 16)
#define AT91_MATRIX_EBI_VDDIOMSEL_3_3V (1 << 16)
#define AT91_MATRIX_EBI_EBI_IOSR (1 << 17) /* EBI I/O slew rate selection */
#define AT91_MATRIX_EBI_EBI_IOSR_REDUCED (0 << 17)
#define AT91_MATRIX_EBI_EBI_IOSR_NORMAL (1 << 17)
#define AT91_MATRIX_EBI_DDR_IOSR (1 << 18) /* DDR2 dedicated port I/O slew rate selection */
#define AT91_MATRIX_EBI_DDR_IOSR_REDUCED (0 << 18)
#define AT91_MATRIX_EBI_DDR_IOSR_NORMAL (1 << 18)
#define AT91_MATRIX_NFD0_SELECT (1 << 24) /* NAND Flash Data Bus Selection */
#define AT91_MATRIX_NFD0_ON_D0 (0 << 24)
#define AT91_MATRIX_NFD0_ON_D16 (1 << 24)
#define AT91_MATRIX_DDR_MP_EN (1 << 25) /* DDR Multi-port Enable */
#define AT91_MATRIX_MP_OFF (0 << 25)
#define AT91_MATRIX_MP_ON (1 << 25)
#define AT91_MATRIX_WPMR (AT91_MATRIX + 0x1E4) /* Write Protect Mode Register */
#define AT91_MATRIX_WPMR_WPEN (1 << 0) /* Write Protect ENable */
#define AT91_MATRIX_WPMR_WP_WPDIS (0 << 0)
#define AT91_MATRIX_WPMR_WP_WPEN (1 << 0)
#define AT91_MATRIX_WPMR_WPKEY (0xFFFFFF << 8) /* Write Protect KEY */
#define AT91_MATRIX_WPSR (AT91_MATRIX + 0x1E8) /* Write Protect Status Register */
#define AT91_MATRIX_WPSR_WPVS (1 << 0) /* Write Protect Violation Status */
#define AT91_MATRIX_WPSR_NO_WPV (0 << 0)
#define AT91_MATRIX_WPSR_WPV (1 << 0)
#define AT91_MATRIX_WPSR_WPVSRC (0xFFFF << 8) /* Write Protect Violation Source */
#endif
...@@ -34,6 +34,8 @@ ...@@ -34,6 +34,8 @@
#include <mach/at91sam9rl.h> #include <mach/at91sam9rl.h>
#elif defined(CONFIG_ARCH_AT91SAM9G45) #elif defined(CONFIG_ARCH_AT91SAM9G45)
#include <mach/at91sam9g45.h> #include <mach/at91sam9g45.h>
#elif defined(CONFIG_ARCH_AT91SAM9X5)
#include <mach/at91sam9x5.h>
#elif defined(CONFIG_ARCH_AT91X40) #elif defined(CONFIG_ARCH_AT91X40)
#include <mach/at91x40.h> #include <mach/at91x40.h>
#else #else
......
...@@ -470,6 +470,11 @@ static struct clk exynos4_init_clocks_off[] = { ...@@ -470,6 +470,11 @@ static struct clk exynos4_init_clocks_off[] = {
.devname = "s5p-mipi-csis.1", .devname = "s5p-mipi-csis.1",
.enable = exynos4_clk_ip_cam_ctrl, .enable = exynos4_clk_ip_cam_ctrl,
.ctrlbit = (1 << 5), .ctrlbit = (1 << 5),
}, {
.name = "jpeg",
.id = 0,
.enable = exynos4_clk_ip_cam_ctrl,
.ctrlbit = (1 << 6),
}, { }, {
.name = "fimc", .name = "fimc",
.devname = "exynos4-fimc.0", .devname = "exynos4-fimc.0",
......
...@@ -26,10 +26,12 @@ ...@@ -26,10 +26,12 @@
#include <asm/hardware/gic.h> #include <asm/hardware/gic.h>
#include <asm/mach/map.h> #include <asm/mach/map.h>
#include <asm/mach/irq.h> #include <asm/mach/irq.h>
#include <asm/cacheflush.h>
#include <mach/regs-irq.h> #include <mach/regs-irq.h>
#include <mach/regs-pmu.h> #include <mach/regs-pmu.h>
#include <mach/regs-gpio.h> #include <mach/regs-gpio.h>
#include <mach/pmu.h>
#include <plat/cpu.h> #include <plat/cpu.h>
#include <plat/clock.h> #include <plat/clock.h>
...@@ -45,6 +47,8 @@ ...@@ -45,6 +47,8 @@
#include <plat/regs-serial.h> #include <plat/regs-serial.h>
#include "common.h" #include "common.h"
#define L2_AUX_VAL 0x7C470001
#define L2_AUX_MASK 0xC200ffff
static const char name_exynos4210[] = "EXYNOS4210"; static const char name_exynos4210[] = "EXYNOS4210";
static const char name_exynos4212[] = "EXYNOS4212"; static const char name_exynos4212[] = "EXYNOS4212";
...@@ -173,7 +177,12 @@ static struct map_desc exynos4_iodesc[] __initdata = { ...@@ -173,7 +177,12 @@ static struct map_desc exynos4_iodesc[] __initdata = {
}, { }, {
.virtual = (unsigned long)S5P_VA_DMC0, .virtual = (unsigned long)S5P_VA_DMC0,
.pfn = __phys_to_pfn(EXYNOS4_PA_DMC0), .pfn = __phys_to_pfn(EXYNOS4_PA_DMC0),
.length = SZ_4K, .length = SZ_64K,
.type = MT_DEVICE,
}, {
.virtual = (unsigned long)S5P_VA_DMC1,
.pfn = __phys_to_pfn(EXYNOS4_PA_DMC1),
.length = SZ_64K,
.type = MT_DEVICE, .type = MT_DEVICE,
}, { }, {
.virtual = (unsigned long)S3C_VA_USB_HSPHY, .virtual = (unsigned long)S3C_VA_USB_HSPHY,
...@@ -433,23 +442,48 @@ core_initcall(exynos4_core_init); ...@@ -433,23 +442,48 @@ core_initcall(exynos4_core_init);
#ifdef CONFIG_CACHE_L2X0 #ifdef CONFIG_CACHE_L2X0
static int __init exynos4_l2x0_cache_init(void) static int __init exynos4_l2x0_cache_init(void)
{ {
/* TAG, Data Latency Control: 2cycle */ int ret;
__raw_writel(0x110, S5P_VA_L2CC + L2X0_TAG_LATENCY_CTRL); ret = l2x0_of_init(L2_AUX_VAL, L2_AUX_MASK);
if (!ret) {
l2x0_regs_phys = virt_to_phys(&l2x0_saved_regs);
clean_dcache_area(&l2x0_regs_phys, sizeof(unsigned long));
return 0;
}
if (soc_is_exynos4210()) if (!(__raw_readl(S5P_VA_L2CC + L2X0_CTRL) & 0x1)) {
__raw_writel(0x110, S5P_VA_L2CC + L2X0_DATA_LATENCY_CTRL); l2x0_saved_regs.phy_base = EXYNOS4_PA_L2CC;
else if (soc_is_exynos4212() || soc_is_exynos4412()) /* TAG, Data Latency Control: 2 cycles */
__raw_writel(0x120, S5P_VA_L2CC + L2X0_DATA_LATENCY_CTRL); l2x0_saved_regs.tag_latency = 0x110;
if (soc_is_exynos4212() || soc_is_exynos4412())
l2x0_saved_regs.data_latency = 0x120;
else
l2x0_saved_regs.data_latency = 0x110;
l2x0_saved_regs.prefetch_ctrl = 0x30000007;
l2x0_saved_regs.pwr_ctrl =
(L2X0_DYNAMIC_CLK_GATING_EN | L2X0_STNDBY_MODE_EN);
l2x0_regs_phys = virt_to_phys(&l2x0_saved_regs);
__raw_writel(l2x0_saved_regs.tag_latency,
S5P_VA_L2CC + L2X0_TAG_LATENCY_CTRL);
__raw_writel(l2x0_saved_regs.data_latency,
S5P_VA_L2CC + L2X0_DATA_LATENCY_CTRL);
/* L2X0 Prefetch Control */ /* L2X0 Prefetch Control */
__raw_writel(0x30000007, S5P_VA_L2CC + L2X0_PREFETCH_CTRL); __raw_writel(l2x0_saved_regs.prefetch_ctrl,
S5P_VA_L2CC + L2X0_PREFETCH_CTRL);
/* L2X0 Power Control */ /* L2X0 Power Control */
__raw_writel(L2X0_DYNAMIC_CLK_GATING_EN | L2X0_STNDBY_MODE_EN, __raw_writel(l2x0_saved_regs.pwr_ctrl,
S5P_VA_L2CC + L2X0_POWER_CTRL); S5P_VA_L2CC + L2X0_POWER_CTRL);
l2x0_init(S5P_VA_L2CC, 0x7C470001, 0xC200ffff); clean_dcache_area(&l2x0_regs_phys, sizeof(unsigned long));
clean_dcache_area(&l2x0_saved_regs, sizeof(struct l2x0_regs));
}
l2x0_init(S5P_VA_L2CC, L2_AUX_VAL, L2_AUX_MASK);
return 0; return 0;
} }
......
...@@ -11,25 +11,53 @@ ...@@ -11,25 +11,53 @@
#include <linux/kernel.h> #include <linux/kernel.h>
#include <linux/init.h> #include <linux/init.h>
#include <linux/cpuidle.h> #include <linux/cpuidle.h>
#include <linux/cpu_pm.h>
#include <linux/io.h> #include <linux/io.h>
#include <linux/export.h> #include <linux/export.h>
#include <linux/time.h> #include <linux/time.h>
#include <asm/proc-fns.h> #include <asm/proc-fns.h>
#include <asm/smp_scu.h>
#include <asm/suspend.h>
#include <asm/unified.h>
#include <mach/regs-pmu.h>
#include <mach/pmu.h>
#include <plat/cpu.h>
#define REG_DIRECTGO_ADDR (samsung_rev() == EXYNOS4210_REV_1_1 ? \
S5P_INFORM7 : (samsung_rev() == EXYNOS4210_REV_1_0 ? \
(S5P_VA_SYSRAM + 0x24) : S5P_INFORM0))
#define REG_DIRECTGO_FLAG (samsung_rev() == EXYNOS4210_REV_1_1 ? \
S5P_INFORM6 : (samsung_rev() == EXYNOS4210_REV_1_0 ? \
(S5P_VA_SYSRAM + 0x20) : S5P_INFORM1))
#define S5P_CHECK_AFTR 0xFCBA0D10
static int exynos4_enter_idle(struct cpuidle_device *dev, static int exynos4_enter_idle(struct cpuidle_device *dev,
struct cpuidle_driver *drv, struct cpuidle_driver *drv,
int index); int index);
static int exynos4_enter_lowpower(struct cpuidle_device *dev,
struct cpuidle_driver *drv,
int index);
static struct cpuidle_state exynos4_cpuidle_set[] = { static struct cpuidle_state exynos4_cpuidle_set[] __initdata = {
[0] = { [0] = {
.enter = exynos4_enter_idle, .enter = exynos4_enter_idle,
.exit_latency = 1, .exit_latency = 1,
.target_residency = 100000, .target_residency = 100000,
.flags = CPUIDLE_FLAG_TIME_VALID, .flags = CPUIDLE_FLAG_TIME_VALID,
.name = "IDLE", .name = "C0",
.desc = "ARM clock gating(WFI)", .desc = "ARM clock gating(WFI)",
}, },
[1] = {
.enter = exynos4_enter_lowpower,
.exit_latency = 300,
.target_residency = 100000,
.flags = CPUIDLE_FLAG_TIME_VALID,
.name = "C1",
.desc = "ARM power down",
},
}; };
static DEFINE_PER_CPU(struct cpuidle_device, exynos4_cpuidle_device); static DEFINE_PER_CPU(struct cpuidle_device, exynos4_cpuidle_device);
...@@ -39,6 +67,99 @@ static struct cpuidle_driver exynos4_idle_driver = { ...@@ -39,6 +67,99 @@ static struct cpuidle_driver exynos4_idle_driver = {
.owner = THIS_MODULE, .owner = THIS_MODULE,
}; };
/* Ext-GIC nIRQ/nFIQ is the only wakeup source in AFTR */
static void exynos4_set_wakeupmask(void)
{
__raw_writel(0x0000ff3e, S5P_WAKEUP_MASK);
}
static unsigned int g_pwr_ctrl, g_diag_reg;
static void save_cpu_arch_register(void)
{
/*read power control register*/
asm("mrc p15, 0, %0, c15, c0, 0" : "=r"(g_pwr_ctrl) : : "cc");
/*read diagnostic register*/
asm("mrc p15, 0, %0, c15, c0, 1" : "=r"(g_diag_reg) : : "cc");
return;
}
static void restore_cpu_arch_register(void)
{
/*write power control register*/
asm("mcr p15, 0, %0, c15, c0, 0" : : "r"(g_pwr_ctrl) : "cc");
/*write diagnostic register*/
asm("mcr p15, 0, %0, c15, c0, 1" : : "r"(g_diag_reg) : "cc");
return;
}
static int idle_finisher(unsigned long flags)
{
cpu_do_idle();
return 1;
}
static int exynos4_enter_core0_aftr(struct cpuidle_device *dev,
struct cpuidle_driver *drv,
int index)
{
struct timeval before, after;
int idle_time;
unsigned long tmp;
local_irq_disable();
do_gettimeofday(&before);
exynos4_set_wakeupmask();
/* Set value of power down register for aftr mode */
exynos4_sys_powerdown_conf(SYS_AFTR);
__raw_writel(virt_to_phys(s3c_cpu_resume), REG_DIRECTGO_ADDR);
__raw_writel(S5P_CHECK_AFTR, REG_DIRECTGO_FLAG);
save_cpu_arch_register();
/* Setting Central Sequence Register for power down mode */
tmp = __raw_readl(S5P_CENTRAL_SEQ_CONFIGURATION);
tmp &= ~S5P_CENTRAL_LOWPWR_CFG;
__raw_writel(tmp, S5P_CENTRAL_SEQ_CONFIGURATION);
cpu_pm_enter();
cpu_suspend(0, idle_finisher);
#ifdef CONFIG_SMP
scu_enable(S5P_VA_SCU);
#endif
cpu_pm_exit();
restore_cpu_arch_register();
/*
* If PMU failed while entering sleep mode, WFI will be
* ignored by PMU and then exiting cpu_do_idle().
* S5P_CENTRAL_LOWPWR_CFG bit will not be set automatically
* in this situation.
*/
tmp = __raw_readl(S5P_CENTRAL_SEQ_CONFIGURATION);
if (!(tmp & S5P_CENTRAL_LOWPWR_CFG)) {
tmp |= S5P_CENTRAL_LOWPWR_CFG;
__raw_writel(tmp, S5P_CENTRAL_SEQ_CONFIGURATION);
}
/* Clear wakeup state register */
__raw_writel(0x0, S5P_WAKEUP_STAT);
do_gettimeofday(&after);
local_irq_enable();
idle_time = (after.tv_sec - before.tv_sec) * USEC_PER_SEC +
(after.tv_usec - before.tv_usec);
dev->last_residency = idle_time;
return index;
}
static int exynos4_enter_idle(struct cpuidle_device *dev, static int exynos4_enter_idle(struct cpuidle_device *dev,
struct cpuidle_driver *drv, struct cpuidle_driver *drv,
int index) int index)
...@@ -60,6 +181,22 @@ static int exynos4_enter_idle(struct cpuidle_device *dev, ...@@ -60,6 +181,22 @@ static int exynos4_enter_idle(struct cpuidle_device *dev,
return index; return index;
} }
static int exynos4_enter_lowpower(struct cpuidle_device *dev,
struct cpuidle_driver *drv,
int index)
{
int new_index = index;
/* This mode only can be entered when other core's are offline */
if (num_online_cpus() > 1)
new_index = drv->safe_state_index;
if (new_index == 0)
return exynos4_enter_idle(dev, drv, new_index);
else
return exynos4_enter_core0_aftr(dev, drv, new_index);
}
static int __init exynos4_init_cpuidle(void) static int __init exynos4_init_cpuidle(void)
{ {
int i, max_cpuidle_state, cpu_id; int i, max_cpuidle_state, cpu_id;
...@@ -74,19 +211,25 @@ static int __init exynos4_init_cpuidle(void) ...@@ -74,19 +211,25 @@ static int __init exynos4_init_cpuidle(void)
memcpy(&drv->states[i], &exynos4_cpuidle_set[i], memcpy(&drv->states[i], &exynos4_cpuidle_set[i],
sizeof(struct cpuidle_state)); sizeof(struct cpuidle_state));
} }
drv->safe_state_index = 0;
cpuidle_register_driver(&exynos4_idle_driver); cpuidle_register_driver(&exynos4_idle_driver);
for_each_cpu(cpu_id, cpu_online_mask) { for_each_cpu(cpu_id, cpu_online_mask) {
device = &per_cpu(exynos4_cpuidle_device, cpu_id); device = &per_cpu(exynos4_cpuidle_device, cpu_id);
device->cpu = cpu_id; device->cpu = cpu_id;
device->state_count = drv->state_count; if (cpu_id == 0)
device->state_count = (sizeof(exynos4_cpuidle_set) /
sizeof(struct cpuidle_state));
else
device->state_count = 1; /* Support IDLE only */
if (cpuidle_register_device(device)) { if (cpuidle_register_device(device)) {
printk(KERN_ERR "CPUidle register device failed\n,"); printk(KERN_ERR "CPUidle register device failed\n,");
return -EIO; return -EIO;
} }
} }
return 0; return 0;
} }
device_initcall(exynos4_init_cpuidle); device_initcall(exynos4_init_cpuidle);
...@@ -31,6 +31,10 @@ ...@@ -31,6 +31,10 @@
#define EXYNOS4_PA_FIMC2 0x11820000 #define EXYNOS4_PA_FIMC2 0x11820000
#define EXYNOS4_PA_FIMC3 0x11830000 #define EXYNOS4_PA_FIMC3 0x11830000
#define EXYNOS4_PA_JPEG 0x11840000
#define EXYNOS4_PA_G2D 0x12800000
#define EXYNOS4_PA_I2S0 0x03830000 #define EXYNOS4_PA_I2S0 0x03830000
#define EXYNOS4_PA_I2S1 0xE3100000 #define EXYNOS4_PA_I2S1 0xE3100000
#define EXYNOS4_PA_I2S2 0xE2A00000 #define EXYNOS4_PA_I2S2 0xE2A00000
...@@ -57,6 +61,7 @@ ...@@ -57,6 +61,7 @@
#define EXYNOS4_PA_KEYPAD 0x100A0000 #define EXYNOS4_PA_KEYPAD 0x100A0000
#define EXYNOS4_PA_DMC0 0x10400000 #define EXYNOS4_PA_DMC0 0x10400000
#define EXYNOS4_PA_DMC1 0x10410000
#define EXYNOS4_PA_COMBINER 0x10440000 #define EXYNOS4_PA_COMBINER 0x10440000
...@@ -162,6 +167,8 @@ ...@@ -162,6 +167,8 @@
#define S5P_PA_FIMC1 EXYNOS4_PA_FIMC1 #define S5P_PA_FIMC1 EXYNOS4_PA_FIMC1
#define S5P_PA_FIMC2 EXYNOS4_PA_FIMC2 #define S5P_PA_FIMC2 EXYNOS4_PA_FIMC2
#define S5P_PA_FIMC3 EXYNOS4_PA_FIMC3 #define S5P_PA_FIMC3 EXYNOS4_PA_FIMC3
#define S5P_PA_JPEG EXYNOS4_PA_JPEG
#define S5P_PA_G2D EXYNOS4_PA_G2D
#define S5P_PA_FIMD0 EXYNOS4_PA_FIMD0 #define S5P_PA_FIMD0 EXYNOS4_PA_FIMD0
#define S5P_PA_HDMI EXYNOS4_PA_HDMI #define S5P_PA_HDMI EXYNOS4_PA_HDMI
#define S5P_PA_IIC_HDMIPHY EXYNOS4_PA_IIC_HDMIPHY #define S5P_PA_IIC_HDMIPHY EXYNOS4_PA_IIC_HDMIPHY
......
...@@ -22,11 +22,13 @@ enum sys_powerdown { ...@@ -22,11 +22,13 @@ enum sys_powerdown {
NUM_SYS_POWERDOWN, NUM_SYS_POWERDOWN,
}; };
extern unsigned long l2x0_regs_phys;
struct exynos4_pmu_conf { struct exynos4_pmu_conf {
void __iomem *reg; void __iomem *reg;
unsigned int val[NUM_SYS_POWERDOWN]; unsigned int val[NUM_SYS_POWERDOWN];
}; };
extern void exynos4_sys_powerdown_conf(enum sys_powerdown mode); extern void exynos4_sys_powerdown_conf(enum sys_powerdown mode);
extern void s3c_cpu_resume(void);
#endif /* __ASM_ARCH_PMU_H */ #endif /* __ASM_ARCH_PMU_H */
...@@ -30,12 +30,13 @@ ...@@ -30,12 +30,13 @@
#include <mach/regs-mct.h> #include <mach/regs-mct.h>
#include <asm/mach/time.h> #include <asm/mach/time.h>
#define TICK_BASE_CNT 1
enum { enum {
MCT_INT_SPI, MCT_INT_SPI,
MCT_INT_PPI MCT_INT_PPI
}; };
static unsigned long clk_cnt_per_tick;
static unsigned long clk_rate; static unsigned long clk_rate;
static unsigned int mct_int_type; static unsigned int mct_int_type;
...@@ -206,11 +207,14 @@ static int exynos4_comp_set_next_event(unsigned long cycles, ...@@ -206,11 +207,14 @@ static int exynos4_comp_set_next_event(unsigned long cycles,
static void exynos4_comp_set_mode(enum clock_event_mode mode, static void exynos4_comp_set_mode(enum clock_event_mode mode,
struct clock_event_device *evt) struct clock_event_device *evt)
{ {
unsigned long cycles_per_jiffy;
exynos4_mct_comp0_stop(); exynos4_mct_comp0_stop();
switch (mode) { switch (mode) {
case CLOCK_EVT_MODE_PERIODIC: case CLOCK_EVT_MODE_PERIODIC:
exynos4_mct_comp0_start(mode, clk_cnt_per_tick); cycles_per_jiffy =
(((unsigned long long) NSEC_PER_SEC / HZ * evt->mult) >> evt->shift);
exynos4_mct_comp0_start(mode, cycles_per_jiffy);
break; break;
case CLOCK_EVT_MODE_ONESHOT: case CLOCK_EVT_MODE_ONESHOT:
...@@ -249,9 +253,7 @@ static struct irqaction mct_comp_event_irq = { ...@@ -249,9 +253,7 @@ static struct irqaction mct_comp_event_irq = {
static void exynos4_clockevent_init(void) static void exynos4_clockevent_init(void)
{ {
clk_cnt_per_tick = clk_rate / 2 / HZ; clockevents_calc_mult_shift(&mct_comp_device, clk_rate, 5);
clockevents_calc_mult_shift(&mct_comp_device, clk_rate / 2, 5);
mct_comp_device.max_delta_ns = mct_comp_device.max_delta_ns =
clockevent_delta2ns(0xffffffff, &mct_comp_device); clockevent_delta2ns(0xffffffff, &mct_comp_device);
mct_comp_device.min_delta_ns = mct_comp_device.min_delta_ns =
...@@ -315,12 +317,15 @@ static inline void exynos4_tick_set_mode(enum clock_event_mode mode, ...@@ -315,12 +317,15 @@ static inline void exynos4_tick_set_mode(enum clock_event_mode mode,
struct clock_event_device *evt) struct clock_event_device *evt)
{ {
struct mct_clock_event_device *mevt = this_cpu_ptr(&percpu_mct_tick); struct mct_clock_event_device *mevt = this_cpu_ptr(&percpu_mct_tick);
unsigned long cycles_per_jiffy;
exynos4_mct_tick_stop(mevt); exynos4_mct_tick_stop(mevt);
switch (mode) { switch (mode) {
case CLOCK_EVT_MODE_PERIODIC: case CLOCK_EVT_MODE_PERIODIC:
exynos4_mct_tick_start(clk_cnt_per_tick, mevt); cycles_per_jiffy =
(((unsigned long long) NSEC_PER_SEC / HZ * evt->mult) >> evt->shift);
exynos4_mct_tick_start(cycles_per_jiffy, mevt);
break; break;
case CLOCK_EVT_MODE_ONESHOT: case CLOCK_EVT_MODE_ONESHOT:
...@@ -394,7 +399,7 @@ static int __cpuinit exynos4_local_timer_setup(struct clock_event_device *evt) ...@@ -394,7 +399,7 @@ static int __cpuinit exynos4_local_timer_setup(struct clock_event_device *evt)
evt->features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT; evt->features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT;
evt->rating = 450; evt->rating = 450;
clockevents_calc_mult_shift(evt, clk_rate / 2, 5); clockevents_calc_mult_shift(evt, clk_rate / (TICK_BASE_CNT + 1), 5);
evt->max_delta_ns = evt->max_delta_ns =
clockevent_delta2ns(0x7fffffff, evt); clockevent_delta2ns(0x7fffffff, evt);
evt->min_delta_ns = evt->min_delta_ns =
...@@ -402,7 +407,7 @@ static int __cpuinit exynos4_local_timer_setup(struct clock_event_device *evt) ...@@ -402,7 +407,7 @@ static int __cpuinit exynos4_local_timer_setup(struct clock_event_device *evt)
clockevents_register_device(evt); clockevents_register_device(evt);
exynos4_mct_write(0x1, mevt->base + MCT_L_TCNTB_OFFSET); exynos4_mct_write(TICK_BASE_CNT, mevt->base + MCT_L_TCNTB_OFFSET);
if (mct_int_type == MCT_INT_SPI) { if (mct_int_type == MCT_INT_SPI) {
if (cpu == 0) { if (cpu == 0) {
......
...@@ -155,13 +155,6 @@ static struct sleep_save exynos4_core_save[] = { ...@@ -155,13 +155,6 @@ static struct sleep_save exynos4_core_save[] = {
SAVE_ITEM(S5P_SROM_BC3), SAVE_ITEM(S5P_SROM_BC3),
}; };
static struct sleep_save exynos4_l2cc_save[] = {
SAVE_ITEM(S5P_VA_L2CC + L2X0_TAG_LATENCY_CTRL),
SAVE_ITEM(S5P_VA_L2CC + L2X0_DATA_LATENCY_CTRL),
SAVE_ITEM(S5P_VA_L2CC + L2X0_PREFETCH_CTRL),
SAVE_ITEM(S5P_VA_L2CC + L2X0_POWER_CTRL),
SAVE_ITEM(S5P_VA_L2CC + L2X0_AUX_CTRL),
};
/* For Cortex-A9 Diagnostic and Power control register */ /* For Cortex-A9 Diagnostic and Power control register */
static unsigned int save_arm_register[2]; static unsigned int save_arm_register[2];
...@@ -182,7 +175,6 @@ static void exynos4_pm_prepare(void) ...@@ -182,7 +175,6 @@ static void exynos4_pm_prepare(void)
u32 tmp; u32 tmp;
s3c_pm_do_save(exynos4_core_save, ARRAY_SIZE(exynos4_core_save)); s3c_pm_do_save(exynos4_core_save, ARRAY_SIZE(exynos4_core_save));
s3c_pm_do_save(exynos4_l2cc_save, ARRAY_SIZE(exynos4_l2cc_save));
s3c_pm_do_save(exynos4_epll_save, ARRAY_SIZE(exynos4_epll_save)); s3c_pm_do_save(exynos4_epll_save, ARRAY_SIZE(exynos4_epll_save));
s3c_pm_do_save(exynos4_vpll_save, ARRAY_SIZE(exynos4_vpll_save)); s3c_pm_do_save(exynos4_vpll_save, ARRAY_SIZE(exynos4_vpll_save));
...@@ -388,13 +380,6 @@ static void exynos4_pm_resume(void) ...@@ -388,13 +380,6 @@ static void exynos4_pm_resume(void)
scu_enable(S5P_VA_SCU); scu_enable(S5P_VA_SCU);
#endif #endif
#ifdef CONFIG_CACHE_L2X0
s3c_pm_do_restore_core(exynos4_l2cc_save, ARRAY_SIZE(exynos4_l2cc_save));
outer_inv_all();
/* enable L2X0*/
writel_relaxed(1, S5P_VA_L2CC + L2X0_CTRL);
#endif
early_wakeup: early_wakeup:
return; return;
} }
......
...@@ -110,7 +110,7 @@ static void __init highbank_timer_init(void) ...@@ -110,7 +110,7 @@ static void __init highbank_timer_init(void)
highbank_clocks_init(); highbank_clocks_init();
sp804_clocksource_init(timer_base + 0x20, "timer1"); sp804_clocksource_and_sched_clock_init(timer_base + 0x20, "timer1");
sp804_clockevents_init(timer_base, irq, "timer0"); sp804_clockevents_init(timer_base, irq, "timer0");
twd_local_timer_of_register(); twd_local_timer_of_register();
......
...@@ -8,8 +8,8 @@ obj-$(CONFIG_SOC_IMX25) += clock-imx25.o mm-imx25.o ehci-imx25.o cpu-imx25.o ...@@ -8,8 +8,8 @@ obj-$(CONFIG_SOC_IMX25) += clock-imx25.o mm-imx25.o ehci-imx25.o cpu-imx25.o
obj-$(CONFIG_SOC_IMX27) += cpu-imx27.o pm-imx27.o obj-$(CONFIG_SOC_IMX27) += cpu-imx27.o pm-imx27.o
obj-$(CONFIG_SOC_IMX27) += clock-imx27.o mm-imx27.o ehci-imx27.o obj-$(CONFIG_SOC_IMX27) += clock-imx27.o mm-imx27.o ehci-imx27.o
obj-$(CONFIG_SOC_IMX31) += mm-imx3.o cpu-imx31.o clock-imx31.o iomux-imx31.o ehci-imx31.o obj-$(CONFIG_SOC_IMX31) += mm-imx3.o cpu-imx31.o clock-imx31.o iomux-imx31.o ehci-imx31.o pm-imx3.o
obj-$(CONFIG_SOC_IMX35) += mm-imx3.o cpu-imx35.o clock-imx35.o ehci-imx35.o obj-$(CONFIG_SOC_IMX35) += mm-imx3.o cpu-imx35.o clock-imx35.o ehci-imx35.o pm-imx3.o
obj-$(CONFIG_SOC_IMX5) += cpu-imx5.o mm-imx5.o clock-mx51-mx53.o ehci-imx5.o pm-imx5.o cpu_op-mx51.o obj-$(CONFIG_SOC_IMX5) += cpu-imx5.o mm-imx5.o clock-mx51-mx53.o ehci-imx5.o pm-imx5.o cpu_op-mx51.o
......
...@@ -149,39 +149,3 @@ int mx50_revision(void) ...@@ -149,39 +149,3 @@ int mx50_revision(void)
return mx5_cpu_rev; return mx5_cpu_rev;
} }
EXPORT_SYMBOL(mx50_revision); EXPORT_SYMBOL(mx50_revision);
static int __init post_cpu_init(void)
{
unsigned int reg;
void __iomem *base;
if (cpu_is_mx51() || cpu_is_mx53()) {
if (cpu_is_mx51())
base = MX51_IO_ADDRESS(MX51_AIPS1_BASE_ADDR);
else
base = MX53_IO_ADDRESS(MX53_AIPS1_BASE_ADDR);
__raw_writel(0x0, base + 0x40);
__raw_writel(0x0, base + 0x44);
__raw_writel(0x0, base + 0x48);
__raw_writel(0x0, base + 0x4C);
reg = __raw_readl(base + 0x50) & 0x00FFFFFF;
__raw_writel(reg, base + 0x50);
if (cpu_is_mx51())
base = MX51_IO_ADDRESS(MX51_AIPS2_BASE_ADDR);
else
base = MX53_IO_ADDRESS(MX53_AIPS2_BASE_ADDR);
__raw_writel(0x0, base + 0x40);
__raw_writel(0x0, base + 0x44);
__raw_writel(0x0, base + 0x48);
__raw_writel(0x0, base + 0x4C);
reg = __raw_readl(base + 0x50) & 0x00FFFFFF;
__raw_writel(reg, base + 0x50);
}
return 0;
}
postcore_initcall(post_cpu_init);
...@@ -77,6 +77,7 @@ MX31_IO_ADDRESS(MX31_CCM_BASE_ADDR) : MX35_IO_ADDRESS(MX35_CCM_BASE_ADDR)) ...@@ -77,6 +77,7 @@ MX31_IO_ADDRESS(MX31_CCM_BASE_ADDR) : MX35_IO_ADDRESS(MX35_CCM_BASE_ADDR))
#define MXC_CCM_CCMR_SSI2S_MASK (0x3 << 21) #define MXC_CCM_CCMR_SSI2S_MASK (0x3 << 21)
#define MXC_CCM_CCMR_LPM_OFFSET 14 #define MXC_CCM_CCMR_LPM_OFFSET 14
#define MXC_CCM_CCMR_LPM_MASK (0x3 << 14) #define MXC_CCM_CCMR_LPM_MASK (0x3 << 14)
#define MXC_CCM_CCMR_LPM_WAIT_MX35 (0x1 << 14)
#define MXC_CCM_CCMR_FIRS_OFFSET 11 #define MXC_CCM_CCMR_FIRS_OFFSET 11
#define MXC_CCM_CCMR_FIRS_MASK (0x3 << 11) #define MXC_CCM_CCMR_FIRS_MASK (0x3 << 11)
#define MXC_CCM_CCMR_UPE (1 << 9) #define MXC_CCM_CCMR_UPE (1 << 9)
......
...@@ -34,6 +34,8 @@ static void imx3_idle(void) ...@@ -34,6 +34,8 @@ static void imx3_idle(void)
{ {
unsigned long reg = 0; unsigned long reg = 0;
mx3_cpu_lp_set(MX3_WAIT);
__asm__ __volatile__( __asm__ __volatile__(
/* disable I and D cache */ /* disable I and D cache */
"mrc p15, 0, %0, c1, c0, 0\n" "mrc p15, 0, %0, c1, c0, 0\n"
...@@ -177,6 +179,10 @@ void __init imx31_soc_init(void) ...@@ -177,6 +179,10 @@ void __init imx31_soc_init(void)
} }
imx_add_imx_sdma("imx31-sdma", MX31_SDMA_BASE_ADDR, MX31_INT_SDMA, &imx31_sdma_pdata); imx_add_imx_sdma("imx31-sdma", MX31_SDMA_BASE_ADDR, MX31_INT_SDMA, &imx31_sdma_pdata);
imx_set_aips(MX31_IO_ADDRESS(MX31_AIPS1_BASE_ADDR));
imx_set_aips(MX31_IO_ADDRESS(MX31_AIPS2_BASE_ADDR));
platform_device_register_simple("imx31-audmux", 0, imx31_audmux_res, platform_device_register_simple("imx31-audmux", 0, imx31_audmux_res,
ARRAY_SIZE(imx31_audmux_res)); ARRAY_SIZE(imx31_audmux_res));
} }
...@@ -267,6 +273,11 @@ void __init imx35_soc_init(void) ...@@ -267,6 +273,11 @@ void __init imx35_soc_init(void)
} }
imx_add_imx_sdma("imx35-sdma", MX35_SDMA_BASE_ADDR, MX35_INT_SDMA, &imx35_sdma_pdata); imx_add_imx_sdma("imx35-sdma", MX35_SDMA_BASE_ADDR, MX35_INT_SDMA, &imx35_sdma_pdata);
/* Setup AIPS registers */
imx_set_aips(MX35_IO_ADDRESS(MX35_AIPS1_BASE_ADDR));
imx_set_aips(MX35_IO_ADDRESS(MX35_AIPS2_BASE_ADDR));
/* i.mx35 has the i.mx31 type audmux */ /* i.mx35 has the i.mx31 type audmux */
platform_device_register_simple("imx31-audmux", 0, imx35_audmux_res, platform_device_register_simple("imx31-audmux", 0, imx35_audmux_res,
ARRAY_SIZE(imx35_audmux_res)); ARRAY_SIZE(imx35_audmux_res));
......
...@@ -201,6 +201,11 @@ void __init imx51_soc_init(void) ...@@ -201,6 +201,11 @@ void __init imx51_soc_init(void)
/* i.mx51 has the i.mx35 type sdma */ /* i.mx51 has the i.mx35 type sdma */
imx_add_imx_sdma("imx35-sdma", MX51_SDMA_BASE_ADDR, MX51_INT_SDMA, &imx51_sdma_pdata); imx_add_imx_sdma("imx35-sdma", MX51_SDMA_BASE_ADDR, MX51_INT_SDMA, &imx51_sdma_pdata);
/* Setup AIPS registers */
imx_set_aips(MX51_IO_ADDRESS(MX51_AIPS1_BASE_ADDR));
imx_set_aips(MX51_IO_ADDRESS(MX51_AIPS2_BASE_ADDR));
/* i.mx51 has the i.mx31 type audmux */ /* i.mx51 has the i.mx31 type audmux */
platform_device_register_simple("imx31-audmux", 0, imx51_audmux_res, platform_device_register_simple("imx31-audmux", 0, imx51_audmux_res,
ARRAY_SIZE(imx51_audmux_res)); ARRAY_SIZE(imx51_audmux_res));
...@@ -219,6 +224,11 @@ void __init imx53_soc_init(void) ...@@ -219,6 +224,11 @@ void __init imx53_soc_init(void)
/* i.mx53 has the i.mx35 type sdma */ /* i.mx53 has the i.mx35 type sdma */
imx_add_imx_sdma("imx35-sdma", MX53_SDMA_BASE_ADDR, MX53_INT_SDMA, &imx53_sdma_pdata); imx_add_imx_sdma("imx35-sdma", MX53_SDMA_BASE_ADDR, MX53_INT_SDMA, &imx53_sdma_pdata);
/* Setup AIPS registers */
imx_set_aips(MX53_IO_ADDRESS(MX53_AIPS1_BASE_ADDR));
imx_set_aips(MX53_IO_ADDRESS(MX53_AIPS2_BASE_ADDR));
/* i.mx53 has the i.mx31 type audmux */ /* i.mx53 has the i.mx31 type audmux */
platform_device_register_simple("imx31-audmux", 0, imx53_audmux_res, platform_device_register_simple("imx31-audmux", 0, imx53_audmux_res,
ARRAY_SIZE(imx53_audmux_res)); ARRAY_SIZE(imx53_audmux_res));
......
/*
* Copyright (C) 2012 Freescale Semiconductor, Inc. All Rights Reserved.
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
*/
#include <linux/io.h>
#include <mach/common.h>
#include <mach/hardware.h>
#include <mach/devices-common.h>
#include "crmregs-imx3.h"
/*
* Set cpu low power mode before WFI instruction. This function is called
* mx3 because it can be used for mx31 and mx35.
* Currently only WAIT_MODE is supported.
*/
void mx3_cpu_lp_set(enum mx3_cpu_pwr_mode mode)
{
int reg = __raw_readl(MXC_CCM_CCMR);
reg &= ~MXC_CCM_CCMR_LPM_MASK;
switch (mode) {
case MX3_WAIT:
if (cpu_is_mx35())
reg |= MXC_CCM_CCMR_LPM_WAIT_MX35;
__raw_writel(reg, MXC_CCM_CCMR);
break;
default:
pr_err("Unknown cpu power mode: %d\n", mode);
return;
}
}
...@@ -223,7 +223,6 @@ static int cpu_clk_set_rate(struct clk *clk, unsigned long rate) ...@@ -223,7 +223,6 @@ static int cpu_clk_set_rate(struct clk *clk, unsigned long rate)
{ {
u32 reg, bm_busy, div_max, d, f, div, frac; u32 reg, bm_busy, div_max, d, f, div, frac;
unsigned long diff, parent_rate, calc_rate; unsigned long diff, parent_rate, calc_rate;
int i;
parent_rate = clk_get_rate(clk->parent); parent_rate = clk_get_rate(clk->parent);
...@@ -275,14 +274,7 @@ static int cpu_clk_set_rate(struct clk *clk, unsigned long rate) ...@@ -275,14 +274,7 @@ static int cpu_clk_set_rate(struct clk *clk, unsigned long rate)
reg |= div << BP_CLKCTRL_CPU_DIV_CPU; reg |= div << BP_CLKCTRL_CPU_DIV_CPU;
__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_CPU); __raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_CPU);
for (i = 10000; i; i--) mxs_clkctrl_timeout(HW_CLKCTRL_CPU, bm_busy);
if (!(__raw_readl(CLKCTRL_BASE_ADDR +
HW_CLKCTRL_CPU) & bm_busy))
break;
if (!i) {
pr_err("%s: divider writing timeout\n", __func__);
return -ETIMEDOUT;
}
return 0; return 0;
} }
...@@ -292,7 +284,6 @@ static int name##_set_rate(struct clk *clk, unsigned long rate) \ ...@@ -292,7 +284,6 @@ static int name##_set_rate(struct clk *clk, unsigned long rate) \
{ \ { \
u32 reg, div_max, div; \ u32 reg, div_max, div; \
unsigned long parent_rate; \ unsigned long parent_rate; \
int i; \
\ \
parent_rate = clk_get_rate(clk->parent); \ parent_rate = clk_get_rate(clk->parent); \
div_max = BM_CLKCTRL_##dr##_DIV >> BP_CLKCTRL_##dr##_DIV; \ div_max = BM_CLKCTRL_##dr##_DIV >> BP_CLKCTRL_##dr##_DIV; \
...@@ -310,15 +301,7 @@ static int name##_set_rate(struct clk *clk, unsigned long rate) \ ...@@ -310,15 +301,7 @@ static int name##_set_rate(struct clk *clk, unsigned long rate) \
} \ } \
__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_##dr); \ __raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_##dr); \
\ \
for (i = 10000; i; i--) \ mxs_clkctrl_timeout(HW_CLKCTRL_##dr, BM_CLKCTRL_##dr##_BUSY); \
if (!(__raw_readl(CLKCTRL_BASE_ADDR + \
HW_CLKCTRL_##dr) & BM_CLKCTRL_##dr##_BUSY)) \
break; \
if (!i) { \
pr_err("%s: divider writing timeout\n", __func__); \
return -ETIMEDOUT; \
} \
\
return 0; \ return 0; \
} }
...@@ -461,7 +444,7 @@ static struct clk_lookup lookups[] = { ...@@ -461,7 +444,7 @@ static struct clk_lookup lookups[] = {
static int clk_misc_init(void) static int clk_misc_init(void)
{ {
u32 reg; u32 reg;
int i; int ret;
/* Fix up parent per register setting */ /* Fix up parent per register setting */
reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_CLKSEQ); reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_CLKSEQ);
...@@ -510,14 +493,7 @@ static int clk_misc_init(void) ...@@ -510,14 +493,7 @@ static int clk_misc_init(void)
reg |= 3 << BP_CLKCTRL_HBUS_DIV; reg |= 3 << BP_CLKCTRL_HBUS_DIV;
__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_HBUS); __raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_HBUS);
for (i = 10000; i; i--) ret = mxs_clkctrl_timeout(HW_CLKCTRL_HBUS, BM_CLKCTRL_HBUS_BUSY);
if (!(__raw_readl(CLKCTRL_BASE_ADDR +
HW_CLKCTRL_HBUS) & BM_CLKCTRL_HBUS_BUSY))
break;
if (!i) {
pr_err("%s: divider writing timeout\n", __func__);
return -ETIMEDOUT;
}
/* Gate off cpu clock in WFI for power saving */ /* Gate off cpu clock in WFI for power saving */
__raw_writel(BM_CLKCTRL_CPU_INTERRUPT_WAIT, __raw_writel(BM_CLKCTRL_CPU_INTERRUPT_WAIT,
...@@ -532,7 +508,7 @@ static int clk_misc_init(void) ...@@ -532,7 +508,7 @@ static int clk_misc_init(void)
reg |= 30 << BP_CLKCTRL_FRAC_IOFRAC; reg |= 30 << BP_CLKCTRL_FRAC_IOFRAC;
__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_FRAC); __raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_FRAC);
return 0; return ret;
} }
int __init mx23_clocks_init(void) int __init mx23_clocks_init(void)
......
...@@ -322,7 +322,6 @@ static int name##_set_rate(struct clk *clk, unsigned long rate) \ ...@@ -322,7 +322,6 @@ static int name##_set_rate(struct clk *clk, unsigned long rate) \
{ \ { \
u32 reg, bm_busy, div_max, d, f, div, frac; \ u32 reg, bm_busy, div_max, d, f, div, frac; \
unsigned long diff, parent_rate, calc_rate; \ unsigned long diff, parent_rate, calc_rate; \
int i; \
\ \
div_max = BM_CLKCTRL_##dr##_DIV >> BP_CLKCTRL_##dr##_DIV; \ div_max = BM_CLKCTRL_##dr##_DIV >> BP_CLKCTRL_##dr##_DIV; \
bm_busy = BM_CLKCTRL_##dr##_BUSY; \ bm_busy = BM_CLKCTRL_##dr##_BUSY; \
...@@ -396,16 +395,7 @@ static int name##_set_rate(struct clk *clk, unsigned long rate) \ ...@@ -396,16 +395,7 @@ static int name##_set_rate(struct clk *clk, unsigned long rate) \
} \ } \
__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_##dr); \ __raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_##dr); \
\ \
for (i = 10000; i; i--) \ return mxs_clkctrl_timeout(HW_CLKCTRL_##dr, bm_busy); \
if (!(__raw_readl(CLKCTRL_BASE_ADDR + \
HW_CLKCTRL_##dr) & bm_busy)) \
break; \
if (!i) { \
pr_err("%s: divider writing timeout\n", __func__); \
return -ETIMEDOUT; \
} \
\
return 0; \
} }
_CLK_SET_RATE(cpu_clk, CPU, FRAC0, CPU) _CLK_SET_RATE(cpu_clk, CPU, FRAC0, CPU)
...@@ -421,7 +411,6 @@ static int name##_set_rate(struct clk *clk, unsigned long rate) \ ...@@ -421,7 +411,6 @@ static int name##_set_rate(struct clk *clk, unsigned long rate) \
{ \ { \
u32 reg, div_max, div; \ u32 reg, div_max, div; \
unsigned long parent_rate; \ unsigned long parent_rate; \
int i; \
\ \
parent_rate = clk_get_rate(clk->parent); \ parent_rate = clk_get_rate(clk->parent); \
div_max = BM_CLKCTRL_##dr##_DIV >> BP_CLKCTRL_##dr##_DIV; \ div_max = BM_CLKCTRL_##dr##_DIV >> BP_CLKCTRL_##dr##_DIV; \
...@@ -439,16 +428,7 @@ static int name##_set_rate(struct clk *clk, unsigned long rate) \ ...@@ -439,16 +428,7 @@ static int name##_set_rate(struct clk *clk, unsigned long rate) \
} \ } \
__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_##dr); \ __raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_##dr); \
\ \
for (i = 10000; i; i--) \ return mxs_clkctrl_timeout(HW_CLKCTRL_##dr, BM_CLKCTRL_##dr##_BUSY);\
if (!(__raw_readl(CLKCTRL_BASE_ADDR + \
HW_CLKCTRL_##dr) & BM_CLKCTRL_##dr##_BUSY)) \
break; \
if (!i) { \
pr_err("%s: divider writing timeout\n", __func__); \
return -ETIMEDOUT; \
} \
\
return 0; \
} }
_CLK_SET_RATE1(xbus_clk, XBUS) _CLK_SET_RATE1(xbus_clk, XBUS)
...@@ -461,7 +441,6 @@ static int name##_set_rate(struct clk *clk, unsigned long rate) \ ...@@ -461,7 +441,6 @@ static int name##_set_rate(struct clk *clk, unsigned long rate) \
u32 reg; \ u32 reg; \
u64 lrate; \ u64 lrate; \
unsigned long parent_rate; \ unsigned long parent_rate; \
int i; \
\ \
parent_rate = clk_get_rate(clk->parent); \ parent_rate = clk_get_rate(clk->parent); \
if (rate > parent_rate) \ if (rate > parent_rate) \
...@@ -477,18 +456,13 @@ static int name##_set_rate(struct clk *clk, unsigned long rate) \ ...@@ -477,18 +456,13 @@ static int name##_set_rate(struct clk *clk, unsigned long rate) \
reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_##rs); \ reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_##rs); \
reg &= ~BM_CLKCTRL_##rs##_DIV; \ reg &= ~BM_CLKCTRL_##rs##_DIV; \
reg |= div << BP_CLKCTRL_##rs##_DIV; \ reg |= div << BP_CLKCTRL_##rs##_DIV; \
__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_##rs); \ if (reg & (1 << clk->enable_shift)) { \
\ pr_err("%s: clock is gated\n", __func__); \
for (i = 10000; i; i--) \ return -EINVAL; \
if (!(__raw_readl(CLKCTRL_BASE_ADDR + \
HW_CLKCTRL_##rs) & BM_CLKCTRL_##rs##_BUSY)) \
break; \
if (!i) { \
pr_err("%s: divider writing timeout\n", __func__); \
return -ETIMEDOUT; \
} \ } \
__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_##rs); \
\ \
return 0; \ return mxs_clkctrl_timeout(HW_CLKCTRL_##rs, BM_CLKCTRL_##rs##_BUSY);\
} }
_CLK_SET_RATE_SAIF(saif0_clk, SAIF0) _CLK_SET_RATE_SAIF(saif0_clk, SAIF0)
...@@ -654,6 +628,8 @@ static struct clk_lookup lookups[] = { ...@@ -654,6 +628,8 @@ static struct clk_lookup lookups[] = {
_REGISTER_CLOCK("mxs-dma-apbx", NULL, xbus_clk) _REGISTER_CLOCK("mxs-dma-apbx", NULL, xbus_clk)
_REGISTER_CLOCK("mxs-mmc.0", NULL, ssp0_clk) _REGISTER_CLOCK("mxs-mmc.0", NULL, ssp0_clk)
_REGISTER_CLOCK("mxs-mmc.1", NULL, ssp1_clk) _REGISTER_CLOCK("mxs-mmc.1", NULL, ssp1_clk)
_REGISTER_CLOCK("mxs-mmc.2", NULL, ssp2_clk)
_REGISTER_CLOCK("mxs-mmc.3", NULL, ssp3_clk)
_REGISTER_CLOCK("flexcan.0", NULL, can0_clk) _REGISTER_CLOCK("flexcan.0", NULL, can0_clk)
_REGISTER_CLOCK("flexcan.1", NULL, can1_clk) _REGISTER_CLOCK("flexcan.1", NULL, can1_clk)
_REGISTER_CLOCK(NULL, "usb0", usb0_clk) _REGISTER_CLOCK(NULL, "usb0", usb0_clk)
...@@ -676,7 +652,7 @@ static struct clk_lookup lookups[] = { ...@@ -676,7 +652,7 @@ static struct clk_lookup lookups[] = {
static int clk_misc_init(void) static int clk_misc_init(void)
{ {
u32 reg; u32 reg;
int i; int ret;
/* Fix up parent per register setting */ /* Fix up parent per register setting */
reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_CLKSEQ); reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_CLKSEQ);
...@@ -756,14 +732,7 @@ static int clk_misc_init(void) ...@@ -756,14 +732,7 @@ static int clk_misc_init(void)
reg |= 3 << BP_CLKCTRL_HBUS_DIV; reg |= 3 << BP_CLKCTRL_HBUS_DIV;
__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_HBUS); __raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_HBUS);
for (i = 10000; i; i--) ret = mxs_clkctrl_timeout(HW_CLKCTRL_HBUS, BM_CLKCTRL_HBUS_ASM_BUSY);
if (!(__raw_readl(CLKCTRL_BASE_ADDR +
HW_CLKCTRL_HBUS) & BM_CLKCTRL_HBUS_ASM_BUSY))
break;
if (!i) {
pr_err("%s: divider writing timeout\n", __func__);
return -ETIMEDOUT;
}
/* Gate off cpu clock in WFI for power saving */ /* Gate off cpu clock in WFI for power saving */
__raw_writel(BM_CLKCTRL_CPU_INTERRUPT_WAIT, __raw_writel(BM_CLKCTRL_CPU_INTERRUPT_WAIT,
...@@ -790,7 +759,7 @@ static int clk_misc_init(void) ...@@ -790,7 +759,7 @@ static int clk_misc_init(void)
reg |= 30 << BP_CLKCTRL_FRAC0_IO0FRAC; reg |= 30 << BP_CLKCTRL_FRAC0_IO0FRAC;
__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_FRAC0); __raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_FRAC0);
return 0; return ret;
} }
int __init mx28_clocks_init(void) int __init mx28_clocks_init(void)
...@@ -803,6 +772,8 @@ int __init mx28_clocks_init(void) ...@@ -803,6 +772,8 @@ int __init mx28_clocks_init(void)
*/ */
clk_set_parent(&ssp0_clk, &ref_io0_clk); clk_set_parent(&ssp0_clk, &ref_io0_clk);
clk_set_parent(&ssp1_clk, &ref_io0_clk); clk_set_parent(&ssp1_clk, &ref_io0_clk);
clk_set_parent(&ssp2_clk, &ref_io1_clk);
clk_set_parent(&ssp3_clk, &ref_io1_clk);
clk_prepare_enable(&cpu_clk); clk_prepare_enable(&cpu_clk);
clk_prepare_enable(&hbus_clk); clk_prepare_enable(&hbus_clk);
......
...@@ -41,6 +41,8 @@ const struct mxs_mxs_mmc_data mx23_mxs_mmc_data[] __initconst = { ...@@ -41,6 +41,8 @@ const struct mxs_mxs_mmc_data mx23_mxs_mmc_data[] __initconst = {
const struct mxs_mxs_mmc_data mx28_mxs_mmc_data[] __initconst = { const struct mxs_mxs_mmc_data mx28_mxs_mmc_data[] __initconst = {
mxs_mxs_mmc_data_entry(MX28, 0, 0), mxs_mxs_mmc_data_entry(MX28, 0, 0),
mxs_mxs_mmc_data_entry(MX28, 1, 1), mxs_mxs_mmc_data_entry(MX28, 1, 1),
mxs_mxs_mmc_data_entry(MX28, 2, 2),
mxs_mxs_mmc_data_entry(MX28, 3, 3),
}; };
#endif #endif
......
...@@ -31,4 +31,6 @@ extern void mx28_init_irq(void); ...@@ -31,4 +31,6 @@ extern void mx28_init_irq(void);
extern void icoll_init_irq(void); extern void icoll_init_irq(void);
extern int mxs_clkctrl_timeout(unsigned int reg_offset, unsigned int mask);
#endif /* __MACH_MXS_COMMON_H__ */ #endif /* __MACH_MXS_COMMON_H__ */
...@@ -37,6 +37,8 @@ ...@@ -37,6 +37,8 @@
#define MXS_MODULE_CLKGATE (1 << 30) #define MXS_MODULE_CLKGATE (1 << 30)
#define MXS_MODULE_SFTRST (1 << 31) #define MXS_MODULE_SFTRST (1 << 31)
#define CLKCTRL_TIMEOUT 10 /* 10 ms */
static void __iomem *mxs_clkctrl_reset_addr; static void __iomem *mxs_clkctrl_reset_addr;
/* /*
...@@ -137,3 +139,17 @@ int mxs_reset_block(void __iomem *reset_addr) ...@@ -137,3 +139,17 @@ int mxs_reset_block(void __iomem *reset_addr)
return -ETIMEDOUT; return -ETIMEDOUT;
} }
EXPORT_SYMBOL(mxs_reset_block); EXPORT_SYMBOL(mxs_reset_block);
int mxs_clkctrl_timeout(unsigned int reg_offset, unsigned int mask)
{
unsigned long timeout = jiffies + msecs_to_jiffies(CLKCTRL_TIMEOUT);
while (readl_relaxed(MXS_IO_ADDRESS(MXS_CLKCTRL_BASE_ADDR)
+ reg_offset) & mask) {
if (time_after(jiffies, timeout)) {
pr_err("Timeout at CLKCTRL + 0x%x\n", reg_offset);
return -ETIMEDOUT;
}
}
return 0;
}
...@@ -29,7 +29,7 @@ ...@@ -29,7 +29,7 @@
#include "control.h" #include "control.h"
static unsigned int omap_revision; static unsigned int omap_revision;
static const char *cpu_rev;
u32 omap_features; u32 omap_features;
unsigned int omap_rev(void) unsigned int omap_rev(void)
...@@ -114,7 +114,7 @@ void omap_get_die_id(struct omap_die_id *odi) ...@@ -114,7 +114,7 @@ void omap_get_die_id(struct omap_die_id *odi)
odi->id_3 = read_tap_reg(OMAP_TAP_DIE_ID_3); odi->id_3 = read_tap_reg(OMAP_TAP_DIE_ID_3);
} }
static void __init omap24xx_check_revision(void) void __init omap2xxx_check_revision(void)
{ {
int i, j; int i, j;
u32 idcode, prod_id; u32 idcode, prod_id;
...@@ -168,13 +168,63 @@ static void __init omap24xx_check_revision(void) ...@@ -168,13 +168,63 @@ static void __init omap24xx_check_revision(void)
pr_info("\n"); pr_info("\n");
} }
#define OMAP3_SHOW_FEATURE(feat) \
if (omap3_has_ ##feat()) \
printk(#feat" ");
static void __init omap3_cpuinfo(void)
{
const char *cpu_name;
/*
* OMAP3430 and OMAP3530 are assumed to be same.
*
* OMAP3525, OMAP3515 and OMAP3503 can be detected only based
* on available features. Upon detection, update the CPU id
* and CPU class bits.
*/
if (cpu_is_omap3630()) {
cpu_name = "OMAP3630";
} else if (cpu_is_omap3517()) {
/* AM35xx devices */
cpu_name = (omap3_has_sgx()) ? "AM3517" : "AM3505";
} else if (cpu_is_ti816x()) {
cpu_name = "TI816X";
} else if (cpu_is_am335x()) {
cpu_name = "AM335X";
} else if (cpu_is_ti814x()) {
cpu_name = "TI814X";
} else if (omap3_has_iva() && omap3_has_sgx()) {
/* OMAP3430, OMAP3525, OMAP3515, OMAP3503 devices */
cpu_name = "OMAP3430/3530";
} else if (omap3_has_iva()) {
cpu_name = "OMAP3525";
} else if (omap3_has_sgx()) {
cpu_name = "OMAP3515";
} else {
cpu_name = "OMAP3503";
}
/* Print verbose information */
pr_info("%s ES%s (", cpu_name, cpu_rev);
OMAP3_SHOW_FEATURE(l2cache);
OMAP3_SHOW_FEATURE(iva);
OMAP3_SHOW_FEATURE(sgx);
OMAP3_SHOW_FEATURE(neon);
OMAP3_SHOW_FEATURE(isp);
OMAP3_SHOW_FEATURE(192mhz_clk);
printk(")\n");
}
#define OMAP3_CHECK_FEATURE(status,feat) \ #define OMAP3_CHECK_FEATURE(status,feat) \
if (((status & OMAP3_ ##feat## _MASK) \ if (((status & OMAP3_ ##feat## _MASK) \
>> OMAP3_ ##feat## _SHIFT) != FEAT_ ##feat## _NONE) { \ >> OMAP3_ ##feat## _SHIFT) != FEAT_ ##feat## _NONE) { \
omap_features |= OMAP3_HAS_ ##feat; \ omap_features |= OMAP3_HAS_ ##feat; \
} }
static void __init omap3_check_features(void) void __init omap3xxx_check_features(void)
{ {
u32 status; u32 status;
...@@ -201,9 +251,11 @@ static void __init omap3_check_features(void) ...@@ -201,9 +251,11 @@ static void __init omap3_check_features(void)
* TODO: Get additional info (where applicable) * TODO: Get additional info (where applicable)
* e.g. Size of L2 cache. * e.g. Size of L2 cache.
*/ */
omap3_cpuinfo();
} }
static void __init omap4_check_features(void) void __init omap4xxx_check_features(void)
{ {
u32 si_type; u32 si_type;
...@@ -228,12 +280,13 @@ static void __init omap4_check_features(void) ...@@ -228,12 +280,13 @@ static void __init omap4_check_features(void)
} }
} }
static void __init ti81xx_check_features(void) void __init ti81xx_check_features(void)
{ {
omap_features = OMAP3_HAS_NEON; omap_features = OMAP3_HAS_NEON;
omap3_cpuinfo();
} }
static void __init omap3_check_revision(const char **cpu_rev) void __init omap3xxx_check_revision(void)
{ {
u32 cpuid, idcode; u32 cpuid, idcode;
u16 hawkeye; u16 hawkeye;
...@@ -247,7 +300,7 @@ static void __init omap3_check_revision(const char **cpu_rev) ...@@ -247,7 +300,7 @@ static void __init omap3_check_revision(const char **cpu_rev)
cpuid = read_cpuid(CPUID_ID); cpuid = read_cpuid(CPUID_ID);
if ((((cpuid >> 4) & 0xfff) == 0xc08) && ((cpuid & 0xf) == 0x0)) { if ((((cpuid >> 4) & 0xfff) == 0xc08) && ((cpuid & 0xf) == 0x0)) {
omap_revision = OMAP3430_REV_ES1_0; omap_revision = OMAP3430_REV_ES1_0;
*cpu_rev = "1.0"; cpu_rev = "1.0";
return; return;
} }
...@@ -268,26 +321,26 @@ static void __init omap3_check_revision(const char **cpu_rev) ...@@ -268,26 +321,26 @@ static void __init omap3_check_revision(const char **cpu_rev)
case 0: /* Take care of early samples */ case 0: /* Take care of early samples */
case 1: case 1:
omap_revision = OMAP3430_REV_ES2_0; omap_revision = OMAP3430_REV_ES2_0;
*cpu_rev = "2.0"; cpu_rev = "2.0";
break; break;
case 2: case 2:
omap_revision = OMAP3430_REV_ES2_1; omap_revision = OMAP3430_REV_ES2_1;
*cpu_rev = "2.1"; cpu_rev = "2.1";
break; break;
case 3: case 3:
omap_revision = OMAP3430_REV_ES3_0; omap_revision = OMAP3430_REV_ES3_0;
*cpu_rev = "3.0"; cpu_rev = "3.0";
break; break;
case 4: case 4:
omap_revision = OMAP3430_REV_ES3_1; omap_revision = OMAP3430_REV_ES3_1;
*cpu_rev = "3.1"; cpu_rev = "3.1";
break; break;
case 7: case 7:
/* FALLTHROUGH */ /* FALLTHROUGH */
default: default:
/* Use the latest known revision as default */ /* Use the latest known revision as default */
omap_revision = OMAP3430_REV_ES3_1_2; omap_revision = OMAP3430_REV_ES3_1_2;
*cpu_rev = "3.1.2"; cpu_rev = "3.1.2";
} }
break; break;
case 0xb868: case 0xb868:
...@@ -300,13 +353,13 @@ static void __init omap3_check_revision(const char **cpu_rev) ...@@ -300,13 +353,13 @@ static void __init omap3_check_revision(const char **cpu_rev)
switch (rev) { switch (rev) {
case 0: case 0:
omap_revision = OMAP3517_REV_ES1_0; omap_revision = OMAP3517_REV_ES1_0;
*cpu_rev = "1.0"; cpu_rev = "1.0";
break; break;
case 1: case 1:
/* FALLTHROUGH */ /* FALLTHROUGH */
default: default:
omap_revision = OMAP3517_REV_ES1_1; omap_revision = OMAP3517_REV_ES1_1;
*cpu_rev = "1.1"; cpu_rev = "1.1";
} }
break; break;
case 0xb891: case 0xb891:
...@@ -315,36 +368,36 @@ static void __init omap3_check_revision(const char **cpu_rev) ...@@ -315,36 +368,36 @@ static void __init omap3_check_revision(const char **cpu_rev)
switch(rev) { switch(rev) {
case 0: /* Take care of early samples */ case 0: /* Take care of early samples */
omap_revision = OMAP3630_REV_ES1_0; omap_revision = OMAP3630_REV_ES1_0;
*cpu_rev = "1.0"; cpu_rev = "1.0";
break; break;
case 1: case 1:
omap_revision = OMAP3630_REV_ES1_1; omap_revision = OMAP3630_REV_ES1_1;
*cpu_rev = "1.1"; cpu_rev = "1.1";
break; break;
case 2: case 2:
/* FALLTHROUGH */ /* FALLTHROUGH */
default: default:
omap_revision = OMAP3630_REV_ES1_2; omap_revision = OMAP3630_REV_ES1_2;
*cpu_rev = "1.2"; cpu_rev = "1.2";
} }
break; break;
case 0xb81e: case 0xb81e:
switch (rev) { switch (rev) {
case 0: case 0:
omap_revision = TI8168_REV_ES1_0; omap_revision = TI8168_REV_ES1_0;
*cpu_rev = "1.0"; cpu_rev = "1.0";
break; break;
case 1: case 1:
/* FALLTHROUGH */ /* FALLTHROUGH */
default: default:
omap_revision = TI8168_REV_ES1_1; omap_revision = TI8168_REV_ES1_1;
*cpu_rev = "1.1"; cpu_rev = "1.1";
break; break;
} }
break; break;
case 0xb944: case 0xb944:
omap_revision = AM335X_REV_ES1_0; omap_revision = AM335X_REV_ES1_0;
*cpu_rev = "1.0"; cpu_rev = "1.0";
break; break;
case 0xb8f2: case 0xb8f2:
switch (rev) { switch (rev) {
...@@ -352,29 +405,29 @@ static void __init omap3_check_revision(const char **cpu_rev) ...@@ -352,29 +405,29 @@ static void __init omap3_check_revision(const char **cpu_rev)
/* FALLTHROUGH */ /* FALLTHROUGH */
case 1: case 1:
omap_revision = TI8148_REV_ES1_0; omap_revision = TI8148_REV_ES1_0;
*cpu_rev = "1.0"; cpu_rev = "1.0";
break; break;
case 2: case 2:
omap_revision = TI8148_REV_ES2_0; omap_revision = TI8148_REV_ES2_0;
*cpu_rev = "2.0"; cpu_rev = "2.0";
break; break;
case 3: case 3:
/* FALLTHROUGH */ /* FALLTHROUGH */
default: default:
omap_revision = TI8148_REV_ES2_1; omap_revision = TI8148_REV_ES2_1;
*cpu_rev = "2.1"; cpu_rev = "2.1";
break; break;
} }
break; break;
default: default:
/* Unknown default to latest silicon rev as default */ /* Unknown default to latest silicon rev as default */
omap_revision = OMAP3630_REV_ES1_2; omap_revision = OMAP3630_REV_ES1_2;
*cpu_rev = "1.2"; cpu_rev = "1.2";
pr_warn("Warning: unknown chip type; assuming OMAP3630ES1.2\n"); pr_warn("Warning: unknown chip type; assuming OMAP3630ES1.2\n");
} }
} }
static void __init omap4_check_revision(void) void __init omap4xxx_check_revision(void)
{ {
u32 idcode; u32 idcode;
u16 hawkeye; u16 hawkeye;
...@@ -447,89 +500,6 @@ static void __init omap4_check_revision(void) ...@@ -447,89 +500,6 @@ static void __init omap4_check_revision(void)
((omap_rev() >> 12) & 0xf), ((omap_rev() >> 8) & 0xf)); ((omap_rev() >> 12) & 0xf), ((omap_rev() >> 8) & 0xf));
} }
#define OMAP3_SHOW_FEATURE(feat) \
if (omap3_has_ ##feat()) \
printk(#feat" ");
static void __init omap3_cpuinfo(const char *cpu_rev)
{
const char *cpu_name;
/*
* OMAP3430 and OMAP3530 are assumed to be same.
*
* OMAP3525, OMAP3515 and OMAP3503 can be detected only based
* on available features. Upon detection, update the CPU id
* and CPU class bits.
*/
if (cpu_is_omap3630()) {
cpu_name = "OMAP3630";
} else if (cpu_is_omap3517()) {
/* AM35xx devices */
cpu_name = (omap3_has_sgx()) ? "AM3517" : "AM3505";
} else if (cpu_is_ti816x()) {
cpu_name = "TI816X";
} else if (cpu_is_am335x()) {
cpu_name = "AM335X";
} else if (cpu_is_ti814x()) {
cpu_name = "TI814X";
} else if (omap3_has_iva() && omap3_has_sgx()) {
/* OMAP3430, OMAP3525, OMAP3515, OMAP3503 devices */
cpu_name = "OMAP3430/3530";
} else if (omap3_has_iva()) {
cpu_name = "OMAP3525";
} else if (omap3_has_sgx()) {
cpu_name = "OMAP3515";
} else {
cpu_name = "OMAP3503";
}
/* Print verbose information */
pr_info("%s ES%s (", cpu_name, cpu_rev);
OMAP3_SHOW_FEATURE(l2cache);
OMAP3_SHOW_FEATURE(iva);
OMAP3_SHOW_FEATURE(sgx);
OMAP3_SHOW_FEATURE(neon);
OMAP3_SHOW_FEATURE(isp);
OMAP3_SHOW_FEATURE(192mhz_clk);
printk(")\n");
}
/*
* Try to detect the exact revision of the omap we're running on
*/
void __init omap2_check_revision(void)
{
const char *cpu_rev;
/*
* At this point we have an idea about the processor revision set
* earlier with omap2_set_globals_tap().
*/
if (cpu_is_omap24xx()) {
omap24xx_check_revision();
} else if (cpu_is_omap34xx()) {
omap3_check_revision(&cpu_rev);
/* TI81XX doesn't have feature register */
if (!cpu_is_ti81xx())
omap3_check_features();
else
ti81xx_check_features();
omap3_cpuinfo(cpu_rev);
return;
} else if (cpu_is_omap44xx()) {
omap4_check_revision();
omap4_check_features();
return;
} else {
pr_err("OMAP revision unknown, please fix!\n");
}
}
/* /*
* Set up things for map_io and processor detection later on. Gets called * Set up things for map_io and processor detection later on. Gets called
* pretty much first thing from board init. For multi-omap, this gets * pretty much first thing from board init. For multi-omap, this gets
......
...@@ -348,7 +348,6 @@ static int _set_hwmod_postsetup_state(struct omap_hwmod *oh, void *data) ...@@ -348,7 +348,6 @@ static int _set_hwmod_postsetup_state(struct omap_hwmod *oh, void *data)
static void __init omap_common_init_early(void) static void __init omap_common_init_early(void)
{ {
omap2_check_revision();
omap_init_consistent_dma_size(); omap_init_consistent_dma_size();
} }
...@@ -389,6 +388,7 @@ static void __init omap_hwmod_init_postsetup(void) ...@@ -389,6 +388,7 @@ static void __init omap_hwmod_init_postsetup(void)
void __init omap2420_init_early(void) void __init omap2420_init_early(void)
{ {
omap2_set_globals_242x(); omap2_set_globals_242x();
omap2xxx_check_revision();
omap_common_init_early(); omap_common_init_early();
omap2xxx_voltagedomains_init(); omap2xxx_voltagedomains_init();
omap242x_powerdomains_init(); omap242x_powerdomains_init();
...@@ -403,6 +403,7 @@ void __init omap2420_init_early(void) ...@@ -403,6 +403,7 @@ void __init omap2420_init_early(void)
void __init omap2430_init_early(void) void __init omap2430_init_early(void)
{ {
omap2_set_globals_243x(); omap2_set_globals_243x();
omap2xxx_check_revision();
omap_common_init_early(); omap_common_init_early();
omap2xxx_voltagedomains_init(); omap2xxx_voltagedomains_init();
omap243x_powerdomains_init(); omap243x_powerdomains_init();
...@@ -421,6 +422,8 @@ void __init omap2430_init_early(void) ...@@ -421,6 +422,8 @@ void __init omap2430_init_early(void)
void __init omap3_init_early(void) void __init omap3_init_early(void)
{ {
omap2_set_globals_3xxx(); omap2_set_globals_3xxx();
omap3xxx_check_revision();
omap3xxx_check_features();
omap_common_init_early(); omap_common_init_early();
omap3xxx_voltagedomains_init(); omap3xxx_voltagedomains_init();
omap3xxx_powerdomains_init(); omap3xxx_powerdomains_init();
...@@ -453,6 +456,8 @@ void __init am35xx_init_early(void) ...@@ -453,6 +456,8 @@ void __init am35xx_init_early(void)
void __init ti81xx_init_early(void) void __init ti81xx_init_early(void)
{ {
omap2_set_globals_ti81xx(); omap2_set_globals_ti81xx();
omap3xxx_check_revision();
ti81xx_check_features();
omap_common_init_early(); omap_common_init_early();
omap3xxx_voltagedomains_init(); omap3xxx_voltagedomains_init();
omap3xxx_powerdomains_init(); omap3xxx_powerdomains_init();
...@@ -467,6 +472,8 @@ void __init ti81xx_init_early(void) ...@@ -467,6 +472,8 @@ void __init ti81xx_init_early(void)
void __init omap4430_init_early(void) void __init omap4430_init_early(void)
{ {
omap2_set_globals_443x(); omap2_set_globals_443x();
omap4xxx_check_revision();
omap4xxx_check_features();
omap_common_init_early(); omap_common_init_early();
omap44xx_voltagedomains_init(); omap44xx_voltagedomains_init();
omap44xx_powerdomains_init(); omap44xx_powerdomains_init();
......
...@@ -83,6 +83,11 @@ config S3C64XX_SETUP_SPI ...@@ -83,6 +83,11 @@ config S3C64XX_SETUP_SPI
help help
Common setup code for SPI GPIO configurations Common setup code for SPI GPIO configurations
config S3C64XX_SETUP_USB_PHY
bool
help
Common setup code for USB PHY controller
# S36400 Macchine support # S36400 Macchine support
config MACH_SMDK6400 config MACH_SMDK6400
...@@ -157,6 +162,7 @@ config MACH_SMDK6410 ...@@ -157,6 +162,7 @@ config MACH_SMDK6410
select S3C64XX_SETUP_IDE select S3C64XX_SETUP_IDE
select S3C64XX_SETUP_FB_24BPP select S3C64XX_SETUP_FB_24BPP
select S3C64XX_SETUP_KEYPAD select S3C64XX_SETUP_KEYPAD
select S3C64XX_SETUP_USB_PHY
help help
Machine support for the Samsung SMDK6410 Machine support for the Samsung SMDK6410
...@@ -256,6 +262,7 @@ config MACH_SMARTQ ...@@ -256,6 +262,7 @@ config MACH_SMARTQ
select S3C_DEV_USB_HOST select S3C_DEV_USB_HOST
select S3C64XX_SETUP_SDHCI select S3C64XX_SETUP_SDHCI
select S3C64XX_SETUP_FB_24BPP select S3C64XX_SETUP_FB_24BPP
select S3C64XX_SETUP_USB_PHY
select SAMSUNG_DEV_ADC select SAMSUNG_DEV_ADC
select SAMSUNG_DEV_PWM select SAMSUNG_DEV_PWM
select SAMSUNG_DEV_TS select SAMSUNG_DEV_TS
...@@ -283,6 +290,7 @@ config MACH_WLF_CRAGG_6410 ...@@ -283,6 +290,7 @@ config MACH_WLF_CRAGG_6410
select S3C64XX_SETUP_FB_24BPP select S3C64XX_SETUP_FB_24BPP
select S3C64XX_SETUP_KEYPAD select S3C64XX_SETUP_KEYPAD
select S3C64XX_SETUP_SPI select S3C64XX_SETUP_SPI
select S3C64XX_SETUP_USB_PHY
select SAMSUNG_DEV_ADC select SAMSUNG_DEV_ADC
select SAMSUNG_DEV_KEYPAD select SAMSUNG_DEV_KEYPAD
select S3C_DEV_USB_HOST select S3C_DEV_USB_HOST
......
...@@ -22,6 +22,7 @@ obj-$(CONFIG_CPU_S3C6410) += s3c6410.o ...@@ -22,6 +22,7 @@ obj-$(CONFIG_CPU_S3C6410) += s3c6410.o
# PM # PM
obj-$(CONFIG_PM) += pm.o irq-pm.o sleep.o obj-$(CONFIG_PM) += pm.o irq-pm.o sleep.o
obj-$(CONFIG_CPU_IDLE) += cpuidle.o
# DMA support # DMA support
...@@ -42,6 +43,7 @@ obj-$(CONFIG_S3C64XX_SETUP_IDE) += setup-ide.o ...@@ -42,6 +43,7 @@ obj-$(CONFIG_S3C64XX_SETUP_IDE) += setup-ide.o
obj-$(CONFIG_S3C64XX_SETUP_KEYPAD) += setup-keypad.o obj-$(CONFIG_S3C64XX_SETUP_KEYPAD) += setup-keypad.o
obj-$(CONFIG_S3C64XX_SETUP_SDHCI_GPIO) += setup-sdhci-gpio.o obj-$(CONFIG_S3C64XX_SETUP_SDHCI_GPIO) += setup-sdhci-gpio.o
obj-$(CONFIG_S3C64XX_SETUP_SPI) += setup-spi.o obj-$(CONFIG_S3C64XX_SETUP_SPI) += setup-spi.o
obj-$(CONFIG_S3C64XX_SETUP_USB_PHY) += setup-usb-phy.o
# Machine support # Machine support
......
...@@ -206,6 +206,15 @@ static struct clk init_clocks_off[] = { ...@@ -206,6 +206,15 @@ static struct clk init_clocks_off[] = {
.parent = &clk_48m, .parent = &clk_48m,
.enable = s3c64xx_sclk_ctrl, .enable = s3c64xx_sclk_ctrl,
.ctrlbit = S3C_CLKCON_SCLK_MMC2_48, .ctrlbit = S3C_CLKCON_SCLK_MMC2_48,
}, {
.name = "ac97",
.parent = &clk_p,
.ctrlbit = S3C_CLKCON_PCLK_AC97,
}, {
.name = "cfcon",
.parent = &clk_h,
.enable = s3c64xx_hclk_ctrl,
.ctrlbit = S3C_CLKCON_HCLK_IHOST,
}, { }, {
.name = "dma0", .name = "dma0",
.parent = &clk_h, .parent = &clk_h,
...@@ -216,6 +225,107 @@ static struct clk init_clocks_off[] = { ...@@ -216,6 +225,107 @@ static struct clk init_clocks_off[] = {
.parent = &clk_h, .parent = &clk_h,
.enable = s3c64xx_hclk_ctrl, .enable = s3c64xx_hclk_ctrl,
.ctrlbit = S3C_CLKCON_HCLK_DMA1, .ctrlbit = S3C_CLKCON_HCLK_DMA1,
}, {
.name = "3dse",
.parent = &clk_h,
.enable = s3c64xx_hclk_ctrl,
.ctrlbit = S3C_CLKCON_HCLK_3DSE,
}, {
.name = "hclk_secur",
.parent = &clk_h,
.enable = s3c64xx_hclk_ctrl,
.ctrlbit = S3C_CLKCON_HCLK_SECUR,
}, {
.name = "sdma1",
.parent = &clk_h,
.enable = s3c64xx_hclk_ctrl,
.ctrlbit = S3C_CLKCON_HCLK_SDMA1,
}, {
.name = "sdma0",
.parent = &clk_h,
.enable = s3c64xx_hclk_ctrl,
.ctrlbit = S3C_CLKCON_HCLK_SDMA0,
}, {
.name = "hclk_jpeg",
.parent = &clk_h,
.enable = s3c64xx_hclk_ctrl,
.ctrlbit = S3C_CLKCON_HCLK_JPEG,
}, {
.name = "camif",
.parent = &clk_h,
.enable = s3c64xx_hclk_ctrl,
.ctrlbit = S3C_CLKCON_HCLK_CAMIF,
}, {
.name = "hclk_scaler",
.parent = &clk_h,
.enable = s3c64xx_hclk_ctrl,
.ctrlbit = S3C_CLKCON_HCLK_SCALER,
}, {
.name = "2d",
.parent = &clk_h,
.enable = s3c64xx_hclk_ctrl,
.ctrlbit = S3C_CLKCON_HCLK_2D,
}, {
.name = "tv",
.parent = &clk_h,
.enable = s3c64xx_hclk_ctrl,
.ctrlbit = S3C_CLKCON_HCLK_TV,
}, {
.name = "post0",
.parent = &clk_h,
.enable = s3c64xx_hclk_ctrl,
.ctrlbit = S3C_CLKCON_HCLK_POST0,
}, {
.name = "rot",
.parent = &clk_h,
.enable = s3c64xx_hclk_ctrl,
.ctrlbit = S3C_CLKCON_HCLK_ROT,
}, {
.name = "hclk_mfc",
.parent = &clk_h,
.enable = s3c64xx_hclk_ctrl,
.ctrlbit = S3C_CLKCON_HCLK_MFC,
}, {
.name = "pclk_mfc",
.parent = &clk_p,
.enable = s3c64xx_pclk_ctrl,
.ctrlbit = S3C_CLKCON_PCLK_MFC,
}, {
.name = "dac27",
.enable = s3c64xx_sclk_ctrl,
.ctrlbit = S3C_CLKCON_SCLK_DAC27,
}, {
.name = "tv27",
.enable = s3c64xx_sclk_ctrl,
.ctrlbit = S3C_CLKCON_SCLK_TV27,
}, {
.name = "scaler27",
.enable = s3c64xx_sclk_ctrl,
.ctrlbit = S3C_CLKCON_SCLK_SCALER27,
}, {
.name = "sclk_scaler",
.enable = s3c64xx_sclk_ctrl,
.ctrlbit = S3C_CLKCON_SCLK_SCALER,
}, {
.name = "post0_27",
.enable = s3c64xx_sclk_ctrl,
.ctrlbit = S3C_CLKCON_SCLK_POST0_27,
}, {
.name = "secur",
.enable = s3c64xx_sclk_ctrl,
.ctrlbit = S3C_CLKCON_SCLK_SECUR,
}, {
.name = "sclk_mfc",
.enable = s3c64xx_sclk_ctrl,
.ctrlbit = S3C_CLKCON_SCLK_MFC,
}, {
.name = "cam",
.enable = s3c64xx_sclk_ctrl,
.ctrlbit = S3C_CLKCON_SCLK_CAM,
}, {
.name = "sclk_jpeg",
.enable = s3c64xx_sclk_ctrl,
.ctrlbit = S3C_CLKCON_SCLK_JPEG,
}, },
}; };
...@@ -289,16 +399,7 @@ static struct clk init_clocks[] = { ...@@ -289,16 +399,7 @@ static struct clk init_clocks[] = {
.name = "watchdog", .name = "watchdog",
.parent = &clk_p, .parent = &clk_p,
.ctrlbit = S3C_CLKCON_PCLK_WDT, .ctrlbit = S3C_CLKCON_PCLK_WDT,
}, { },
.name = "ac97",
.parent = &clk_p,
.ctrlbit = S3C_CLKCON_PCLK_AC97,
}, {
.name = "cfcon",
.parent = &clk_h,
.enable = s3c64xx_hclk_ctrl,
.ctrlbit = S3C_CLKCON_HCLK_IHOST,
}
}; };
static struct clk clk_hsmmc0 = { static struct clk clk_hsmmc0 = {
......
/* linux/arch/arm/mach-s3c64xx/cpuidle.c
*
* Copyright (c) 2011 Wolfson Microelectronics, plc
* Copyright (c) 2011 Samsung Electronics Co., Ltd.
* http://www.samsung.com
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/cpuidle.h>
#include <linux/io.h>
#include <linux/export.h>
#include <linux/time.h>
#include <asm/proc-fns.h>
#include <mach/map.h>
#include <mach/regs-sys.h>
#include <mach/regs-syscon-power.h>
static int s3c64xx_enter_idle(struct cpuidle_device *dev,
struct cpuidle_driver *drv,
int index)
{
struct timeval before, after;
unsigned long tmp;
int idle_time;
local_irq_disable();
do_gettimeofday(&before);
/* Setup PWRCFG to enter idle mode */
tmp = __raw_readl(S3C64XX_PWR_CFG);
tmp &= ~S3C64XX_PWRCFG_CFG_WFI_MASK;
tmp |= S3C64XX_PWRCFG_CFG_WFI_IDLE;
__raw_writel(tmp, S3C64XX_PWR_CFG);
cpu_do_idle();
do_gettimeofday(&after);
local_irq_enable();
idle_time = (after.tv_sec - before.tv_sec) * USEC_PER_SEC +
(after.tv_usec - before.tv_usec);
dev->last_residency = idle_time;
return index;
}
static struct cpuidle_state s3c64xx_cpuidle_set[] = {
[0] = {
.enter = s3c64xx_enter_idle,
.exit_latency = 1,
.target_residency = 1,
.flags = CPUIDLE_FLAG_TIME_VALID,
.name = "IDLE",
.desc = "System active, ARM gated",
},
};
static struct cpuidle_driver s3c64xx_cpuidle_driver = {
.name = "s3c64xx_cpuidle",
.owner = THIS_MODULE,
.state_count = ARRAY_SIZE(s3c64xx_cpuidle_set),
};
static struct cpuidle_device s3c64xx_cpuidle_device = {
.state_count = ARRAY_SIZE(s3c64xx_cpuidle_set),
};
static int __init s3c64xx_init_cpuidle(void)
{
int ret;
memcpy(s3c64xx_cpuidle_driver.states, s3c64xx_cpuidle_set,
sizeof(s3c64xx_cpuidle_set));
cpuidle_register_driver(&s3c64xx_cpuidle_driver);
ret = cpuidle_register_device(&s3c64xx_cpuidle_device);
if (ret) {
pr_err("Failed to register cpuidle device: %d\n", ret);
return ret;
}
return 0;
}
device_initcall(s3c64xx_init_cpuidle);
...@@ -59,6 +59,7 @@ ...@@ -59,6 +59,7 @@
#include <plat/sdhci.h> #include <plat/sdhci.h>
#include <plat/gpio-cfg.h> #include <plat/gpio-cfg.h>
#include <plat/s3c64xx-spi.h> #include <plat/s3c64xx-spi.h>
#include <plat/udc-hs.h>
#include <plat/keypad.h> #include <plat/keypad.h>
#include <plat/clock.h> #include <plat/clock.h>
...@@ -698,6 +699,8 @@ static struct s3c_sdhci_platdata crag6410_hsmmc0_pdata = { ...@@ -698,6 +699,8 @@ static struct s3c_sdhci_platdata crag6410_hsmmc0_pdata = {
.cfg_gpio = crag6410_cfg_sdhci0, .cfg_gpio = crag6410_cfg_sdhci0,
}; };
static struct s3c_hsotg_plat crag6410_hsotg_pdata;
static void __init crag6410_machine_init(void) static void __init crag6410_machine_init(void)
{ {
/* Open drain IRQs need pullups */ /* Open drain IRQs need pullups */
...@@ -722,6 +725,7 @@ static void __init crag6410_machine_init(void) ...@@ -722,6 +725,7 @@ static void __init crag6410_machine_init(void)
s3c_i2c0_set_platdata(&i2c0_pdata); s3c_i2c0_set_platdata(&i2c0_pdata);
s3c_i2c1_set_platdata(&i2c1_pdata); s3c_i2c1_set_platdata(&i2c1_pdata);
s3c_fb_set_platdata(&crag6410_lcd_pdata); s3c_fb_set_platdata(&crag6410_lcd_pdata);
s3c_hsotg_set_platdata(&crag6410_hsotg_pdata);
i2c_register_board_info(0, i2c_devs0, ARRAY_SIZE(i2c_devs0)); i2c_register_board_info(0, i2c_devs0, ARRAY_SIZE(i2c_devs0));
i2c_register_board_info(1, i2c_devs1, ARRAY_SIZE(i2c_devs1)); i2c_register_board_info(1, i2c_devs1, ARRAY_SIZE(i2c_devs1));
......
...@@ -187,6 +187,8 @@ static struct s3c_hwmon_pdata smartq_hwmon_pdata __initdata = { ...@@ -187,6 +187,8 @@ static struct s3c_hwmon_pdata smartq_hwmon_pdata __initdata = {
}, },
}; };
static struct s3c_hsotg_plat smartq_hsotg_pdata;
static int __init smartq_lcd_setup_gpio(void) static int __init smartq_lcd_setup_gpio(void)
{ {
int ret; int ret;
...@@ -383,6 +385,7 @@ void __init smartq_map_io(void) ...@@ -383,6 +385,7 @@ void __init smartq_map_io(void)
void __init smartq_machine_init(void) void __init smartq_machine_init(void)
{ {
s3c_i2c0_set_platdata(NULL); s3c_i2c0_set_platdata(NULL);
s3c_hsotg_set_platdata(&smartq_hsotg_pdata);
s3c_hwmon_set_platdata(&smartq_hwmon_pdata); s3c_hwmon_set_platdata(&smartq_hwmon_pdata);
s3c_sdhci1_set_platdata(&smartq_internal_hsmmc_pdata); s3c_sdhci1_set_platdata(&smartq_internal_hsmmc_pdata);
s3c_sdhci2_set_platdata(&smartq_internal_hsmmc_pdata); s3c_sdhci2_set_platdata(&smartq_internal_hsmmc_pdata);
......
...@@ -72,6 +72,7 @@ ...@@ -72,6 +72,7 @@
#include <plat/keypad.h> #include <plat/keypad.h>
#include <plat/backlight.h> #include <plat/backlight.h>
#include <plat/regs-fb-v4.h> #include <plat/regs-fb-v4.h>
#include <plat/udc-hs.h>
#include "common.h" #include "common.h"
...@@ -631,6 +632,8 @@ static struct platform_pwm_backlight_data smdk6410_bl_data = { ...@@ -631,6 +632,8 @@ static struct platform_pwm_backlight_data smdk6410_bl_data = {
.pwm_id = 1, .pwm_id = 1,
}; };
static struct s3c_hsotg_plat smdk6410_hsotg_pdata;
static void __init smdk6410_map_io(void) static void __init smdk6410_map_io(void)
{ {
u32 tmp; u32 tmp;
...@@ -659,6 +662,7 @@ static void __init smdk6410_machine_init(void) ...@@ -659,6 +662,7 @@ static void __init smdk6410_machine_init(void)
s3c_i2c0_set_platdata(NULL); s3c_i2c0_set_platdata(NULL);
s3c_i2c1_set_platdata(NULL); s3c_i2c1_set_platdata(NULL);
s3c_fb_set_platdata(&smdk6410_lcd_pdata); s3c_fb_set_platdata(&smdk6410_lcd_pdata);
s3c_hsotg_set_platdata(&smdk6410_hsotg_pdata);
samsung_keypad_set_platdata(&smdk6410_keypad_data); samsung_keypad_set_platdata(&smdk6410_keypad_data);
......
/*
* Copyright (C) 2011 Samsung Electronics Co.Ltd
* Author: Joonyoung Shim <jy0922.shim@samsung.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
*/
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/io.h>
#include <linux/platform_device.h>
#include <mach/map.h>
#include <mach/regs-sys.h>
#include <plat/cpu.h>
#include <plat/regs-usb-hsotg-phy.h>
#include <plat/usb-phy.h>
static int s3c_usb_otgphy_init(struct platform_device *pdev)
{
struct clk *xusbxti;
u32 phyclk;
writel(readl(S3C64XX_OTHERS) | S3C64XX_OTHERS_USBMASK, S3C64XX_OTHERS);
/* set clock frequency for PLL */
phyclk = readl(S3C_PHYCLK) & ~S3C_PHYCLK_CLKSEL_MASK;
xusbxti = clk_get(&pdev->dev, "xusbxti");
if (xusbxti && !IS_ERR(xusbxti)) {
switch (clk_get_rate(xusbxti)) {
case 12 * MHZ:
phyclk |= S3C_PHYCLK_CLKSEL_12M;
break;
case 24 * MHZ:
phyclk |= S3C_PHYCLK_CLKSEL_24M;
break;
default:
case 48 * MHZ:
/* default reference clock */
break;
}
clk_put(xusbxti);
}
/* TODO: select external clock/oscillator */
writel(phyclk | S3C_PHYCLK_CLK_FORCE, S3C_PHYCLK);
/* set to normal OTG PHY */
writel((readl(S3C_PHYPWR) & ~S3C_PHYPWR_NORMAL_MASK), S3C_PHYPWR);
mdelay(1);
/* reset OTG PHY and Link */
writel(S3C_RSTCON_PHY | S3C_RSTCON_HCLK | S3C_RSTCON_PHYCLK,
S3C_RSTCON);
udelay(20); /* at-least 10uS */
writel(0, S3C_RSTCON);
return 0;
}
static int s3c_usb_otgphy_exit(struct platform_device *pdev)
{
writel((readl(S3C_PHYPWR) | S3C_PHYPWR_ANALOG_POWERDOWN |
S3C_PHYPWR_OTG_DISABLE), S3C_PHYPWR);
writel(readl(S3C64XX_OTHERS) & ~S3C64XX_OTHERS_USBMASK, S3C64XX_OTHERS);
return 0;
}
int s5p_usb_phy_init(struct platform_device *pdev, int type)
{
if (type == S5P_USB_PHY_DEVICE)
return s3c_usb_otgphy_init(pdev);
return -EINVAL;
}
int s5p_usb_phy_exit(struct platform_device *pdev, int type)
{
if (type == S5P_USB_PHY_DEVICE)
return s3c_usb_otgphy_exit(pdev);
return -EINVAL;
}
...@@ -65,6 +65,11 @@ config S5PV210_SETUP_SPI ...@@ -65,6 +65,11 @@ config S5PV210_SETUP_SPI
help help
Common setup code for SPI GPIO configurations. Common setup code for SPI GPIO configurations.
config S5PV210_SETUP_USB_PHY
bool
help
Common setup code for USB PHY controller
menu "S5PC110 Machines" menu "S5PC110 Machines"
config MACH_AQUILA config MACH_AQUILA
...@@ -107,6 +112,7 @@ config MACH_GONI ...@@ -107,6 +112,7 @@ config MACH_GONI
select S5PV210_SETUP_KEYPAD select S5PV210_SETUP_KEYPAD
select S5PV210_SETUP_SDHCI select S5PV210_SETUP_SDHCI
select S5PV210_SETUP_FIMC select S5PV210_SETUP_FIMC
select S5PV210_SETUP_USB_PHY
help help
Machine support for Samsung GONI board Machine support for Samsung GONI board
S5PC110(MCP) is one of package option of S5PV210 S5PC110(MCP) is one of package option of S5PV210
......
...@@ -39,3 +39,4 @@ obj-$(CONFIG_S5PV210_SETUP_IDE) += setup-ide.o ...@@ -39,3 +39,4 @@ obj-$(CONFIG_S5PV210_SETUP_IDE) += setup-ide.o
obj-$(CONFIG_S5PV210_SETUP_KEYPAD) += setup-keypad.o obj-$(CONFIG_S5PV210_SETUP_KEYPAD) += setup-keypad.o
obj-$(CONFIG_S5PV210_SETUP_SDHCI_GPIO) += setup-sdhci-gpio.o obj-$(CONFIG_S5PV210_SETUP_SDHCI_GPIO) += setup-sdhci-gpio.o
obj-$(CONFIG_S5PV210_SETUP_SPI) += setup-spi.o obj-$(CONFIG_S5PV210_SETUP_SPI) += setup-spi.o
obj-$(CONFIG_S5PV210_SETUP_USB_PHY) += setup-usb-phy.o
...@@ -13,7 +13,3 @@ ...@@ -13,7 +13,3 @@
#define S5PV210_USB_PHY_CON (S3C_VA_SYS + 0xE80C) #define S5PV210_USB_PHY_CON (S3C_VA_SYS + 0xE80C)
#define S5PV210_USB_PHY0_EN (1 << 0) #define S5PV210_USB_PHY0_EN (1 << 0)
#define S5PV210_USB_PHY1_EN (1 << 1) #define S5PV210_USB_PHY1_EN (1 << 1)
/* compatibility defines for s3c-hsotg driver */
#define S3C64XX_OTHERS S5PV210_USB_PHY_CON
#define S3C64XX_OTHERS_USBMASK S5PV210_USB_PHY0_EN
/*
* Copyright (C) 2012 Samsung Electronics Co.Ltd
* Author: Joonyoung Shim <jy0922.shim@samsung.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundationr
*/
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/io.h>
#include <linux/platform_device.h>
#include <mach/map.h>
#include <mach/regs-sys.h>
#include <plat/cpu.h>
#include <plat/regs-usb-hsotg-phy.h>
#include <plat/usb-phy.h>
static int s5pv210_usb_otgphy_init(struct platform_device *pdev)
{
struct clk *xusbxti;
u32 phyclk;
writel(readl(S5PV210_USB_PHY_CON) | S5PV210_USB_PHY0_EN,
S5PV210_USB_PHY_CON);
/* set clock frequency for PLL */
phyclk = readl(S3C_PHYCLK) & ~S3C_PHYCLK_CLKSEL_MASK;
xusbxti = clk_get(&pdev->dev, "xusbxti");
if (xusbxti && !IS_ERR(xusbxti)) {
switch (clk_get_rate(xusbxti)) {
case 12 * MHZ:
phyclk |= S3C_PHYCLK_CLKSEL_12M;
break;
case 24 * MHZ:
phyclk |= S3C_PHYCLK_CLKSEL_24M;
break;
default:
case 48 * MHZ:
/* default reference clock */
break;
}
clk_put(xusbxti);
}
/* TODO: select external clock/oscillator */
writel(phyclk | S3C_PHYCLK_CLK_FORCE, S3C_PHYCLK);
/* set to normal OTG PHY */
writel((readl(S3C_PHYPWR) & ~S3C_PHYPWR_NORMAL_MASK), S3C_PHYPWR);
mdelay(1);
/* reset OTG PHY and Link */
writel(S3C_RSTCON_PHY | S3C_RSTCON_HCLK | S3C_RSTCON_PHYCLK,
S3C_RSTCON);
udelay(20); /* at-least 10uS */
writel(0, S3C_RSTCON);
return 0;
}
static int s5pv210_usb_otgphy_exit(struct platform_device *pdev)
{
writel((readl(S3C_PHYPWR) | S3C_PHYPWR_ANALOG_POWERDOWN |
S3C_PHYPWR_OTG_DISABLE), S3C_PHYPWR);
writel(readl(S5PV210_USB_PHY_CON) & ~S5PV210_USB_PHY0_EN,
S5PV210_USB_PHY_CON);
return 0;
}
int s5p_usb_phy_init(struct platform_device *pdev, int type)
{
if (type == S5P_USB_PHY_DEVICE)
return s5pv210_usb_otgphy_init(pdev);
return -EINVAL;
}
int s5p_usb_phy_exit(struct platform_device *pdev, int type)
{
if (type == S5P_USB_PHY_DEVICE)
return s5pv210_usb_otgphy_exit(pdev);
return -EINVAL;
}
...@@ -7,12 +7,15 @@ obj-y += clock.o ...@@ -7,12 +7,15 @@ obj-y += clock.o
obj-y += timer.o obj-y += timer.o
obj-y += pinmux.o obj-y += pinmux.o
obj-y += fuse.o obj-y += fuse.o
obj-$(CONFIG_CPU_IDLE) += cpuidle.o
obj-$(CONFIG_CPU_IDLE) += sleep.o
obj-$(CONFIG_ARCH_TEGRA_2x_SOC) += powergate.o obj-$(CONFIG_ARCH_TEGRA_2x_SOC) += powergate.o
obj-$(CONFIG_ARCH_TEGRA_2x_SOC) += tegra2_clocks.o obj-$(CONFIG_ARCH_TEGRA_2x_SOC) += tegra2_clocks.o
obj-$(CONFIG_ARCH_TEGRA_2x_SOC) += tegra2_emc.o obj-$(CONFIG_ARCH_TEGRA_2x_SOC) += tegra2_emc.o
obj-$(CONFIG_ARCH_TEGRA_2x_SOC) += pinmux-tegra20-tables.o obj-$(CONFIG_ARCH_TEGRA_2x_SOC) += pinmux-tegra20-tables.o
obj-$(CONFIG_ARCH_TEGRA_3x_SOC) += pinmux-tegra30-tables.o obj-$(CONFIG_ARCH_TEGRA_3x_SOC) += pinmux-tegra30-tables.o
obj-$(CONFIG_ARCH_TEGRA_3x_SOC) += board-dt-tegra30.o obj-$(CONFIG_ARCH_TEGRA_3x_SOC) += board-dt-tegra30.o
obj-$(CONFIG_ARCH_TEGRA_3x_SOC) += tegra30_clocks.o
obj-$(CONFIG_SMP) += platsmp.o headsmp.o obj-$(CONFIG_SMP) += platsmp.o headsmp.o
obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
obj-$(CONFIG_TEGRA_SYSTEM_DMA) += dma.o obj-$(CONFIG_TEGRA_SYSTEM_DMA) += dma.o
......
...@@ -34,16 +34,38 @@ ...@@ -34,16 +34,38 @@
#include <asm/hardware/gic.h> #include <asm/hardware/gic.h>
#include "board.h" #include "board.h"
#include "clock.h"
static struct of_device_id tegra_dt_match_table[] __initdata = { static struct of_device_id tegra_dt_match_table[] __initdata = {
{ .compatible = "simple-bus", }, { .compatible = "simple-bus", },
{} {}
}; };
struct of_dev_auxdata tegra30_auxdata_lookup[] __initdata = {
OF_DEV_AUXDATA("nvidia,tegra20-sdhci", 0x78000000, "sdhci-tegra.0", NULL),
OF_DEV_AUXDATA("nvidia,tegra20-sdhci", 0x78000200, "sdhci-tegra.1", NULL),
OF_DEV_AUXDATA("nvidia,tegra20-sdhci", 0x78000400, "sdhci-tegra.2", NULL),
OF_DEV_AUXDATA("nvidia,tegra20-sdhci", 0x78000600, "sdhci-tegra.3", NULL),
OF_DEV_AUXDATA("nvidia,tegra20-i2c", 0x7000C000, "tegra-i2c.0", NULL),
OF_DEV_AUXDATA("nvidia,tegra20-i2c", 0x7000C400, "tegra-i2c.1", NULL),
OF_DEV_AUXDATA("nvidia,tegra20-i2c", 0x7000C500, "tegra-i2c.2", NULL),
OF_DEV_AUXDATA("nvidia,tegra20-i2c", 0x7000C700, "tegra-i2c.3", NULL),
OF_DEV_AUXDATA("nvidia,tegra20-i2c", 0x7000D000, "tegra-i2c.4", NULL),
{}
};
static __initdata struct tegra_clk_init_table tegra_dt_clk_init_table[] = {
/* name parent rate enabled */
{ "uartd", "pll_p", 408000000, true },
{ NULL, NULL, 0, 0},
};
static void __init tegra30_dt_init(void) static void __init tegra30_dt_init(void)
{ {
tegra_clk_init_from_table(tegra_dt_clk_init_table);
of_platform_populate(NULL, tegra_dt_match_table, of_platform_populate(NULL, tegra_dt_match_table,
NULL, NULL); tegra30_auxdata_lookup, NULL);
} }
static const char *tegra30_dt_board_compat[] = { static const char *tegra30_dt_board_compat[] = {
......
...@@ -399,6 +399,28 @@ void tegra_periph_reset_assert(struct clk *c) ...@@ -399,6 +399,28 @@ void tegra_periph_reset_assert(struct clk *c)
} }
EXPORT_SYMBOL(tegra_periph_reset_assert); EXPORT_SYMBOL(tegra_periph_reset_assert);
/* Several extended clock configuration bits (e.g., clock routing, clock
* phase control) are included in PLL and peripheral clock source
* registers. */
int tegra_clk_cfg_ex(struct clk *c, enum tegra_clk_ex_param p, u32 setting)
{
int ret = 0;
unsigned long flags;
spin_lock_irqsave(&c->spinlock, flags);
if (!c->ops || !c->ops->clk_cfg_ex) {
ret = -ENOSYS;
goto out;
}
ret = c->ops->clk_cfg_ex(c, p, setting);
out:
spin_unlock_irqrestore(&c->spinlock, flags);
return ret;
}
#ifdef CONFIG_DEBUG_FS #ifdef CONFIG_DEBUG_FS
static int __clk_lock_all_spinlocks(void) static int __clk_lock_all_spinlocks(void)
......
...@@ -24,6 +24,8 @@ ...@@ -24,6 +24,8 @@
#include <linux/list.h> #include <linux/list.h>
#include <linux/spinlock.h> #include <linux/spinlock.h>
#include <mach/clk.h>
#define DIV_BUS (1 << 0) #define DIV_BUS (1 << 0)
#define DIV_U71 (1 << 1) #define DIV_U71 (1 << 1)
#define DIV_U71_FIXED (1 << 2) #define DIV_U71_FIXED (1 << 2)
...@@ -39,7 +41,16 @@ ...@@ -39,7 +41,16 @@
#define PERIPH_MANUAL_RESET (1 << 12) #define PERIPH_MANUAL_RESET (1 << 12)
#define PLL_ALT_MISC_REG (1 << 13) #define PLL_ALT_MISC_REG (1 << 13)
#define PLLU (1 << 14) #define PLLU (1 << 14)
#define PLLX (1 << 15)
#define MUX_PWM (1 << 16)
#define MUX8 (1 << 17)
#define DIV_U71_UART (1 << 18)
#define MUX_CLK_OUT (1 << 19)
#define PLLM (1 << 20)
#define DIV_U71_INT (1 << 21)
#define DIV_U71_IDLE (1 << 22)
#define ENABLE_ON_INIT (1 << 28) #define ENABLE_ON_INIT (1 << 28)
#define PERIPH_ON_APB (1 << 29)
struct clk; struct clk;
...@@ -65,6 +76,8 @@ struct clk_ops { ...@@ -65,6 +76,8 @@ struct clk_ops {
int (*set_rate)(struct clk *, unsigned long); int (*set_rate)(struct clk *, unsigned long);
long (*round_rate)(struct clk *, unsigned long); long (*round_rate)(struct clk *, unsigned long);
void (*reset)(struct clk *, bool); void (*reset)(struct clk *, bool);
int (*clk_cfg_ex)(struct clk *,
enum tegra_clk_ex_param, u32);
}; };
enum clk_state { enum clk_state {
...@@ -114,6 +127,7 @@ struct clk { ...@@ -114,6 +127,7 @@ struct clk {
unsigned long vco_max; unsigned long vco_max;
const struct clk_pll_freq_table *freq_table; const struct clk_pll_freq_table *freq_table;
int lock_delay; int lock_delay;
unsigned long fixed_rate;
} pll; } pll;
struct { struct {
u32 sel; u32 sel;
...@@ -146,6 +160,7 @@ struct tegra_clk_init_table { ...@@ -146,6 +160,7 @@ struct tegra_clk_init_table {
}; };
void tegra2_init_clocks(void); void tegra2_init_clocks(void);
void tegra30_init_clocks(void);
void clk_init(struct clk *clk); void clk_init(struct clk *clk);
struct clk *tegra_get_clock_by_name(const char *name); struct clk *tegra_get_clock_by_name(const char *name);
int clk_reparent(struct clk *c, struct clk *parent); int clk_reparent(struct clk *c, struct clk *parent);
......
...@@ -104,6 +104,7 @@ void __init tegra20_init_early(void) ...@@ -104,6 +104,7 @@ void __init tegra20_init_early(void)
#ifdef CONFIG_ARCH_TEGRA_3x_SOC #ifdef CONFIG_ARCH_TEGRA_3x_SOC
void __init tegra30_init_early(void) void __init tegra30_init_early(void)
{ {
tegra30_init_clocks();
tegra_init_cache(0x441, 0x551); tegra_init_cache(0x441, 0x551);
} }
#endif #endif
/*
* arch/arm/mach-tegra/cpuidle.c
*
* CPU idle driver for Tegra CPUs
*
* Copyright (c) 2010-2012, NVIDIA Corporation.
* Copyright (c) 2011 Google, Inc.
* Author: Colin Cross <ccross@android.com>
* Gary King <gking@nvidia.com>
*
* Rework for 3.3 by Peter De Schrijver <pdeschrijver@nvidia.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
* more details.
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/cpu.h>
#include <linux/cpuidle.h>
#include <linux/hrtimer.h>
#include <mach/iomap.h>
extern void tegra_cpu_wfi(void);
static int tegra_idle_enter_lp3(struct cpuidle_device *dev,
struct cpuidle_driver *drv, int index);
struct cpuidle_driver tegra_idle_driver = {
.name = "tegra_idle",
.owner = THIS_MODULE,
.state_count = 1,
.states = {
[0] = {
.enter = tegra_idle_enter_lp3,
.exit_latency = 10,
.target_residency = 10,
.power_usage = 600,
.flags = CPUIDLE_FLAG_TIME_VALID,
.name = "LP3",
.desc = "CPU flow-controlled",
},
},
};
static DEFINE_PER_CPU(struct cpuidle_device, tegra_idle_device);
static int tegra_idle_enter_lp3(struct cpuidle_device *dev,
struct cpuidle_driver *drv, int index)
{
ktime_t enter, exit;
s64 us;
local_irq_disable();
local_fiq_disable();
enter = ktime_get();
tegra_cpu_wfi();
exit = ktime_sub(ktime_get(), enter);
us = ktime_to_us(exit);
local_fiq_enable();
local_irq_enable();
dev->last_residency = us;
return index;
}
static int __init tegra_cpuidle_init(void)
{
int ret;
unsigned int cpu;
struct cpuidle_device *dev;
struct cpuidle_driver *drv = &tegra_idle_driver;
ret = cpuidle_register_driver(&tegra_idle_driver);
if (ret) {
pr_err("CPUidle driver registration failed\n");
return ret;
}
for_each_possible_cpu(cpu) {
dev = &per_cpu(tegra_idle_device, cpu);
dev->cpu = cpu;
dev->state_count = drv->state_count;
ret = cpuidle_register_device(dev);
if (ret) {
pr_err("CPU%u: CPUidle device registration failed\n",
cpu);
return ret;
}
}
return 0;
}
device_initcall(tegra_cpuidle_init);
/*
* arch/arm/mach-tegra/flowctrl.h
*
* functions and macros to control the flowcontroller
*
* Copyright (c) 2010-2012, NVIDIA Corporation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms and conditions of the GNU General Public License,
* version 2, as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
* more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#ifndef __MACH_TEGRA_FLOWCTRL_H
#define __MACH_TEGRA_FLOWCTRL_H
#define FLOW_CTRL_HALT_CPU0_EVENTS 0x0
#define FLOW_CTRL_WAITEVENT (2 << 29)
#define FLOW_CTRL_WAIT_FOR_INTERRUPT (4 << 29)
#define FLOW_CTRL_JTAG_RESUME (1 << 28)
#define FLOW_CTRL_HALT_CPU_IRQ (1 << 10)
#define FLOW_CTRL_HALT_CPU_FIQ (1 << 8)
#define FLOW_CTRL_CPU0_CSR 0x8
#define FLOW_CTRL_CSR_INTR_FLAG (1 << 15)
#define FLOW_CTRL_CSR_EVENT_FLAG (1 << 14)
#define FLOW_CTRL_CSR_ENABLE (1 << 0)
#define FLOW_CTRL_HALT_CPU1_EVENTS 0x14
#define FLOW_CTRL_CPU1_CSR 0x18
#endif
...@@ -22,10 +22,20 @@ ...@@ -22,10 +22,20 @@
struct clk; struct clk;
enum tegra_clk_ex_param {
TEGRA_CLK_VI_INP_SEL,
TEGRA_CLK_DTV_INVERT,
TEGRA_CLK_NAND_PAD_DIV2_ENB,
TEGRA_CLK_PLLD_CSI_OUT_ENB,
TEGRA_CLK_PLLD_DSI_OUT_ENB,
TEGRA_CLK_PLLD_MIPI_MUX_SEL,
};
void tegra_periph_reset_deassert(struct clk *c); void tegra_periph_reset_deassert(struct clk *c);
void tegra_periph_reset_assert(struct clk *c); void tegra_periph_reset_assert(struct clk *c);
unsigned long clk_get_rate_all_locked(struct clk *c); unsigned long clk_get_rate_all_locked(struct clk *c);
void tegra2_sdmmc_tap_delay(struct clk *c, int delay); void tegra2_sdmmc_tap_delay(struct clk *c, int delay);
int tegra_clk_cfg_ex(struct clk *c, enum tegra_clk_ex_param p, u32 setting);
#endif #endif
...@@ -74,6 +74,9 @@ ...@@ -74,6 +74,9 @@
#define TEGRA_QUATERNARY_ICTLR_BASE 0x60004300 #define TEGRA_QUATERNARY_ICTLR_BASE 0x60004300
#define TEGRA_QUATERNARY_ICTLR_SIZE SZ_64 #define TEGRA_QUATERNARY_ICTLR_SIZE SZ_64
#define TEGRA_QUINARY_ICTLR_BASE 0x60004400
#define TEGRA_QUINARY_ICTLR_SIZE SZ_64
#define TEGRA_TMR1_BASE 0x60005000 #define TEGRA_TMR1_BASE 0x60005000
#define TEGRA_TMR1_SIZE SZ_8 #define TEGRA_TMR1_SIZE SZ_8
......
...@@ -165,11 +165,12 @@ ...@@ -165,11 +165,12 @@
#define INT_QUAD_RES_30 (INT_QUAD_BASE + 30) #define INT_QUAD_RES_30 (INT_QUAD_BASE + 30)
#define INT_QUAD_RES_31 (INT_QUAD_BASE + 31) #define INT_QUAD_RES_31 (INT_QUAD_BASE + 31)
#define INT_MAIN_NR (INT_QUAD_BASE + 32 - INT_PRI_BASE) /* Tegra30 has 5 banks of 32 IRQs */
#define INT_MAIN_NR (32 * 5)
#define INT_GPIO_BASE (INT_PRI_BASE + INT_MAIN_NR) #define INT_GPIO_BASE (INT_PRI_BASE + INT_MAIN_NR)
#define INT_GPIO_NR (28 * 8) /* Tegra30 has 8 banks of 32 GPIOs */
#define INT_GPIO_NR (32 * 8)
#define TEGRA_NR_IRQS (INT_GPIO_BASE + INT_GPIO_NR) #define TEGRA_NR_IRQS (INT_GPIO_BASE + INT_GPIO_NR)
......
...@@ -44,14 +44,16 @@ ...@@ -44,14 +44,16 @@
#define ICTLR_COP_IER_CLR 0x38 #define ICTLR_COP_IER_CLR 0x38
#define ICTLR_COP_IEP_CLASS 0x3c #define ICTLR_COP_IEP_CLASS 0x3c
#define NUM_ICTLRS 4
#define FIRST_LEGACY_IRQ 32 #define FIRST_LEGACY_IRQ 32
static int num_ictlrs;
static void __iomem *ictlr_reg_base[] = { static void __iomem *ictlr_reg_base[] = {
IO_ADDRESS(TEGRA_PRIMARY_ICTLR_BASE), IO_ADDRESS(TEGRA_PRIMARY_ICTLR_BASE),
IO_ADDRESS(TEGRA_SECONDARY_ICTLR_BASE), IO_ADDRESS(TEGRA_SECONDARY_ICTLR_BASE),
IO_ADDRESS(TEGRA_TERTIARY_ICTLR_BASE), IO_ADDRESS(TEGRA_TERTIARY_ICTLR_BASE),
IO_ADDRESS(TEGRA_QUATERNARY_ICTLR_BASE), IO_ADDRESS(TEGRA_QUATERNARY_ICTLR_BASE),
IO_ADDRESS(TEGRA_QUINARY_ICTLR_BASE),
}; };
static inline void tegra_irq_write_mask(unsigned int irq, unsigned long reg) static inline void tegra_irq_write_mask(unsigned int irq, unsigned long reg)
...@@ -60,7 +62,7 @@ static inline void tegra_irq_write_mask(unsigned int irq, unsigned long reg) ...@@ -60,7 +62,7 @@ static inline void tegra_irq_write_mask(unsigned int irq, unsigned long reg)
u32 mask; u32 mask;
BUG_ON(irq < FIRST_LEGACY_IRQ || BUG_ON(irq < FIRST_LEGACY_IRQ ||
irq >= FIRST_LEGACY_IRQ + NUM_ICTLRS * 32); irq >= FIRST_LEGACY_IRQ + num_ictlrs * 32);
base = ictlr_reg_base[(irq - FIRST_LEGACY_IRQ) / 32]; base = ictlr_reg_base[(irq - FIRST_LEGACY_IRQ) / 32];
mask = BIT((irq - FIRST_LEGACY_IRQ) % 32); mask = BIT((irq - FIRST_LEGACY_IRQ) % 32);
...@@ -113,8 +115,18 @@ static int tegra_retrigger(struct irq_data *d) ...@@ -113,8 +115,18 @@ static int tegra_retrigger(struct irq_data *d)
void __init tegra_init_irq(void) void __init tegra_init_irq(void)
{ {
int i; int i;
void __iomem *distbase;
distbase = IO_ADDRESS(TEGRA_ARM_INT_DIST_BASE);
num_ictlrs = readl_relaxed(distbase + GIC_DIST_CTR) & 0x1f;
if (num_ictlrs > ARRAY_SIZE(ictlr_reg_base)) {
WARN(1, "Too many (%d) interrupt controllers found. Maximum is %d.",
num_ictlrs, ARRAY_SIZE(ictlr_reg_base));
num_ictlrs = ARRAY_SIZE(ictlr_reg_base);
}
for (i = 0; i < NUM_ICTLRS; i++) { for (i = 0; i < num_ictlrs; i++) {
void __iomem *ictlr = ictlr_reg_base[i]; void __iomem *ictlr = ictlr_reg_base[i];
writel(~0, ictlr + ICTLR_CPU_IER_CLR); writel(~0, ictlr + ICTLR_CPU_IER_CLR);
writel(0, ictlr + ICTLR_CPU_IEP_CLASS); writel(0, ictlr + ICTLR_CPU_IEP_CLASS);
...@@ -131,6 +143,6 @@ void __init tegra_init_irq(void) ...@@ -131,6 +143,6 @@ void __init tegra_init_irq(void)
* initialized elsewhere under DT. * initialized elsewhere under DT.
*/ */
if (!of_have_populated_dt()) if (!of_have_populated_dt())
gic_init(0, 29, IO_ADDRESS(TEGRA_ARM_INT_DIST_BASE), gic_init(0, 29, distbase,
IO_ADDRESS(TEGRA_ARM_PERIF_BASE + 0x100)); IO_ADDRESS(TEGRA_ARM_PERIF_BASE + 0x100));
} }
/*
* arch/arm/mach-tegra/sleep.S
*
* Copyright (c) 2010-2011, NVIDIA Corporation.
* Copyright (c) 2011, Google, Inc.
*
* Author: Colin Cross <ccross@android.com>
* Gary King <gking@nvidia.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
* more details.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA.
*/
#include <linux/linkage.h>
#include <mach/io.h>
#include <mach/iomap.h>
#include "flowctrl.h"
#define TEGRA_FLOW_CTRL_VIRT (TEGRA_FLOW_CTRL_BASE - IO_PPSB_PHYS \
+ IO_PPSB_VIRT)
/* returns the offset of the flow controller halt register for a cpu */
.macro cpu_to_halt_reg rd, rcpu
cmp \rcpu, #0
subne \rd, \rcpu, #1
movne \rd, \rd, lsl #3
addne \rd, \rd, #0x14
moveq \rd, #0
.endm
/* returns the offset of the flow controller csr register for a cpu */
.macro cpu_to_csr_reg rd, rcpu
cmp \rcpu, #0
subne \rd, \rcpu, #1
movne \rd, \rd, lsl #3
addne \rd, \rd, #0x18
moveq \rd, #8
.endm
/* returns the ID of the current processor */
.macro cpu_id, rd
mrc p15, 0, \rd, c0, c0, 5
and \rd, \rd, #0xF
.endm
/* loads a 32-bit value into a register without a data access */
.macro mov32, reg, val
movw \reg, #:lower16:\val
movt \reg, #:upper16:\val
.endm
/*
* tegra_cpu_wfi
*
* puts current CPU in clock-gated wfi using the flow controller
*
* corrupts r0-r3
* must be called with MMU on
*/
ENTRY(tegra_cpu_wfi)
cpu_id r0
cpu_to_halt_reg r1, r0
cpu_to_csr_reg r2, r0
mov32 r0, TEGRA_FLOW_CTRL_VIRT
mov r3, #FLOW_CTRL_CSR_INTR_FLAG | FLOW_CTRL_CSR_EVENT_FLAG
str r3, [r0, r2] @ clear event & interrupt status
mov r3, #FLOW_CTRL_WAIT_FOR_INTERRUPT | FLOW_CTRL_JTAG_RESUME
str r3, [r0, r1] @ put flow controller in wait irq mode
dsb
wfi
mov r3, #0
str r3, [r0, r1] @ clear flow controller halt status
mov r3, #FLOW_CTRL_CSR_INTR_FLAG | FLOW_CTRL_CSR_EVENT_FLAG
str r3, [r0, r2] @ clear event & interrupt status
dsb
mov pc, lr
ENDPROC(tegra_cpu_wfi)
...@@ -1143,15 +1143,35 @@ static void tegra2_emc_clk_init(struct clk *c) ...@@ -1143,15 +1143,35 @@ static void tegra2_emc_clk_init(struct clk *c)
static long tegra2_emc_clk_round_rate(struct clk *c, unsigned long rate) static long tegra2_emc_clk_round_rate(struct clk *c, unsigned long rate)
{ {
long new_rate = rate; long emc_rate;
long clk_rate;
new_rate = tegra_emc_round_rate(new_rate); /*
if (new_rate < 0) * The slowest entry in the EMC clock table that is at least as
* fast as rate.
*/
emc_rate = tegra_emc_round_rate(rate);
if (emc_rate < 0)
return c->max_rate; return c->max_rate;
BUG_ON(new_rate != tegra2_periph_clk_round_rate(c, new_rate)); /*
* The fastest rate the PLL will generate that is at most the
* requested rate.
*/
clk_rate = tegra2_periph_clk_round_rate(c, emc_rate);
/*
* If this fails, and emc_rate > clk_rate, it's because the maximum
* rate in the EMC tables is larger than the maximum rate of the EMC
* clock. The EMC clock's max rate is the rate it was running when the
* kernel booted. Such a mismatch is probably due to using the wrong
* BCT, i.e. using a Tegra20 BCT with an EMC table written for Tegra25.
*/
WARN_ONCE(emc_rate != clk_rate,
"emc_rate %ld != clk_rate %ld",
emc_rate, clk_rate);
return new_rate; return emc_rate;
} }
static int tegra2_emc_clk_set_rate(struct clk *c, unsigned long rate) static int tegra2_emc_clk_set_rate(struct clk *c, unsigned long rate)
......
This diff is collapsed.
#include <linux/module.h> #include <linux/module.h>
#include <linux/io.h>
#include <mach/hardware.h> #include <mach/hardware.h>
unsigned int __mxc_cpu_type; unsigned int __mxc_cpu_type;
...@@ -18,3 +19,26 @@ void imx_print_silicon_rev(const char *cpu, int srev) ...@@ -18,3 +19,26 @@ void imx_print_silicon_rev(const char *cpu, int srev)
pr_info("CPU identified as %s, silicon rev %d.%d\n", pr_info("CPU identified as %s, silicon rev %d.%d\n",
cpu, (srev >> 4) & 0xf, srev & 0xf); cpu, (srev >> 4) & 0xf, srev & 0xf);
} }
void __init imx_set_aips(void __iomem *base)
{
unsigned int reg;
/*
* Set all MPROTx to be non-bufferable, trusted for R/W,
* not forced to user-mode.
*/
__raw_writel(0x77777777, base + 0x0);
__raw_writel(0x77777777, base + 0x4);
/*
* Set all OPACRx to be non-bufferable, to not require
* supervisor privilege level for access, allow for
* write access and untrusted master access.
*/
__raw_writel(0x0, base + 0x40);
__raw_writel(0x0, base + 0x44);
__raw_writel(0x0, base + 0x48);
__raw_writel(0x0, base + 0x4C);
reg = __raw_readl(base + 0x50) & 0x00FFFFFF;
__raw_writel(reg, base + 0x50);
}
...@@ -75,6 +75,7 @@ extern void mxc_restart(char, const char *); ...@@ -75,6 +75,7 @@ extern void mxc_restart(char, const char *);
extern void mxc_arch_reset_init(void __iomem *); extern void mxc_arch_reset_init(void __iomem *);
extern int mx53_revision(void); extern int mx53_revision(void);
extern int mx53_display_revision(void); extern int mx53_display_revision(void);
extern void imx_set_aips(void __iomem *);
enum mxc_cpu_pwr_mode { enum mxc_cpu_pwr_mode {
WAIT_CLOCKED, /* wfi only */ WAIT_CLOCKED, /* wfi only */
...@@ -84,6 +85,14 @@ enum mxc_cpu_pwr_mode { ...@@ -84,6 +85,14 @@ enum mxc_cpu_pwr_mode {
STOP_POWER_OFF, /* STOP + SRPG */ STOP_POWER_OFF, /* STOP + SRPG */
}; };
enum mx3_cpu_pwr_mode {
MX3_RUN,
MX3_WAIT,
MX3_DOZE,
MX3_SLEEP,
};
extern void mx3_cpu_lp_set(enum mx3_cpu_pwr_mode mode);
extern void mx5_cpu_lp_set(enum mxc_cpu_pwr_mode mode); extern void mx5_cpu_lp_set(enum mxc_cpu_pwr_mode mode);
extern void imx_print_silicon_rev(const char *cpu, int srev); extern void imx_print_silicon_rev(const char *cpu, int srev);
......
...@@ -449,7 +449,12 @@ IS_OMAP_TYPE(3517, 0x3517) ...@@ -449,7 +449,12 @@ IS_OMAP_TYPE(3517, 0x3517)
#define OMAP447X_CLASS 0x44700044 #define OMAP447X_CLASS 0x44700044
#define OMAP4470_REV_ES1_0 (OMAP447X_CLASS | (0x10 << 8)) #define OMAP4470_REV_ES1_0 (OMAP447X_CLASS | (0x10 << 8))
void omap2_check_revision(void); void omap2xxx_check_revision(void);
void omap3xxx_check_revision(void);
void omap4xxx_check_revision(void);
void omap3xxx_check_features(void);
void ti81xx_check_features(void);
void omap4xxx_check_features(void);
/* /*
* Runtime detection of OMAP3 features * Runtime detection of OMAP3 features
......
...@@ -80,6 +80,16 @@ config S5P_DEV_FIMC3 ...@@ -80,6 +80,16 @@ config S5P_DEV_FIMC3
help help
Compile in platform device definitions for FIMC controller 3 Compile in platform device definitions for FIMC controller 3
config S5P_DEV_JPEG
bool
help
Compile in platform device definitions for JPEG codec
config S5P_DEV_G2D
bool
help
Compile in platform device definitions for G2D device
config S5P_DEV_FIMD0 config S5P_DEV_FIMD0
bool bool
help help
......
...@@ -23,9 +23,18 @@ ...@@ -23,9 +23,18 @@
*/ */
#include <linux/linkage.h> #include <linux/linkage.h>
#include <asm/assembler.h> #include <asm/asm-offsets.h>
#include <asm/hardware/cache-l2x0.h>
.text /*
* The following code is located into the .data section. This is to
* allow l2x0_regs_phys to be accessed with a relative load while we
* can't rely on any MMU translation. We could have put l2x0_regs_phys
* in the .text section as well, but some setups might insist on it to
* be truly read-only. (Reference from: arch/arm/kernel/sleep.S)
*/
.data
.align
/* /*
* sleep magic, to allow the bootloader to check for an valid * sleep magic, to allow the bootloader to check for an valid
...@@ -39,11 +48,34 @@ ...@@ -39,11 +48,34 @@
* s3c_cpu_resume * s3c_cpu_resume
* *
* resume code entry for bootloader to call * resume code entry for bootloader to call
*
* we must put this code here in the data segment as we have no
* other way of restoring the stack pointer after sleep, and we
* must not write to the code segment (code is read-only)
*/ */
ENTRY(s3c_cpu_resume) ENTRY(s3c_cpu_resume)
#ifdef CONFIG_CACHE_L2X0
adr r0, l2x0_regs_phys
ldr r0, [r0]
ldr r1, [r0, #L2X0_R_PHY_BASE]
ldr r2, [r1, #L2X0_CTRL]
tst r2, #0x1
bne resume_l2on
ldr r2, [r0, #L2X0_R_AUX_CTRL]
str r2, [r1, #L2X0_AUX_CTRL]
ldr r2, [r0, #L2X0_R_TAG_LATENCY]
str r2, [r1, #L2X0_TAG_LATENCY_CTRL]
ldr r2, [r0, #L2X0_R_DATA_LATENCY]
str r2, [r1, #L2X0_DATA_LATENCY_CTRL]
ldr r2, [r0, #L2X0_R_PREFETCH_CTRL]
str r2, [r1, #L2X0_PREFETCH_CTRL]
ldr r2, [r0, #L2X0_R_PWR_CTRL]
str r2, [r1, #L2X0_POWER_CTRL]
mov r2, #1
str r2, [r1, #L2X0_CTRL]
resume_l2on:
#endif
b cpu_resume b cpu_resume
ENDPROC(s3c_cpu_resume)
#ifdef CONFIG_CACHE_L2X0
.globl l2x0_regs_phys
l2x0_regs_phys:
.long 0
#endif
...@@ -84,31 +84,35 @@ static int clk_null_enable(struct clk *clk, int enable) ...@@ -84,31 +84,35 @@ static int clk_null_enable(struct clk *clk, int enable)
int clk_enable(struct clk *clk) int clk_enable(struct clk *clk)
{ {
unsigned long flags;
if (IS_ERR(clk) || clk == NULL) if (IS_ERR(clk) || clk == NULL)
return -EINVAL; return -EINVAL;
clk_enable(clk->parent); clk_enable(clk->parent);
spin_lock(&clocks_lock); spin_lock_irqsave(&clocks_lock, flags);
if ((clk->usage++) == 0) if ((clk->usage++) == 0)
(clk->enable)(clk, 1); (clk->enable)(clk, 1);
spin_unlock(&clocks_lock); spin_unlock_irqrestore(&clocks_lock, flags);
return 0; return 0;
} }
void clk_disable(struct clk *clk) void clk_disable(struct clk *clk)
{ {
unsigned long flags;
if (IS_ERR(clk) || clk == NULL) if (IS_ERR(clk) || clk == NULL)
return; return;
spin_lock(&clocks_lock); spin_lock_irqsave(&clocks_lock, flags);
if ((--clk->usage) == 0) if ((--clk->usage) == 0)
(clk->enable)(clk, 0); (clk->enable)(clk, 0);
spin_unlock(&clocks_lock); spin_unlock_irqrestore(&clocks_lock, flags);
clk_disable(clk->parent); clk_disable(clk->parent);
} }
......
...@@ -77,7 +77,7 @@ static struct platform_device samsung_dfl_bl_device __initdata = { ...@@ -77,7 +77,7 @@ static struct platform_device samsung_dfl_bl_device __initdata = {
* @gpio_info: structure containing GPIO info for PWM timer * @gpio_info: structure containing GPIO info for PWM timer
* @bl_data: structure containing Backlight control data * @bl_data: structure containing Backlight control data
*/ */
void samsung_bl_set(struct samsung_bl_gpio_info *gpio_info, void __init samsung_bl_set(struct samsung_bl_gpio_info *gpio_info,
struct platform_pwm_backlight_data *bl_data) struct platform_pwm_backlight_data *bl_data)
{ {
int ret = 0; int ret = 0;
...@@ -115,6 +115,8 @@ void samsung_bl_set(struct samsung_bl_gpio_info *gpio_info, ...@@ -115,6 +115,8 @@ void samsung_bl_set(struct samsung_bl_gpio_info *gpio_info,
samsung_bl_data->init = bl_data->init; samsung_bl_data->init = bl_data->init;
if (bl_data->notify) if (bl_data->notify)
samsung_bl_data->notify = bl_data->notify; samsung_bl_data->notify = bl_data->notify;
if (bl_data->notify_after)
samsung_bl_data->notify_after = bl_data->notify_after;
if (bl_data->exit) if (bl_data->exit)
samsung_bl_data->exit = bl_data->exit; samsung_bl_data->exit = bl_data->exit;
if (bl_data->check_fb) if (bl_data->check_fb)
......
...@@ -57,6 +57,7 @@ ...@@ -57,6 +57,7 @@
#include <plat/sdhci.h> #include <plat/sdhci.h>
#include <plat/ts.h> #include <plat/ts.h>
#include <plat/udc.h> #include <plat/udc.h>
#include <plat/udc-hs.h>
#include <plat/usb-control.h> #include <plat/usb-control.h>
#include <plat/usb-phy.h> #include <plat/usb-phy.h>
#include <plat/regs-iic.h> #include <plat/regs-iic.h>
...@@ -267,6 +268,52 @@ struct platform_device s5p_device_fimc3 = { ...@@ -267,6 +268,52 @@ struct platform_device s5p_device_fimc3 = {
}; };
#endif /* CONFIG_S5P_DEV_FIMC3 */ #endif /* CONFIG_S5P_DEV_FIMC3 */
/* G2D */
#ifdef CONFIG_S5P_DEV_G2D
static struct resource s5p_g2d_resource[] = {
[0] = {
.start = S5P_PA_G2D,
.end = S5P_PA_G2D + SZ_4K - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = IRQ_2D,
.end = IRQ_2D,
.flags = IORESOURCE_IRQ,
},
};
struct platform_device s5p_device_g2d = {
.name = "s5p-g2d",
.id = 0,
.num_resources = ARRAY_SIZE(s5p_g2d_resource),
.resource = s5p_g2d_resource,
.dev = {
.dma_mask = &samsung_device_dma_mask,
.coherent_dma_mask = DMA_BIT_MASK(32),
},
};
#endif /* CONFIG_S5P_DEV_G2D */
#ifdef CONFIG_S5P_DEV_JPEG
static struct resource s5p_jpeg_resource[] = {
[0] = DEFINE_RES_MEM(S5P_PA_JPEG, SZ_4K),
[1] = DEFINE_RES_IRQ(IRQ_JPEG),
};
struct platform_device s5p_device_jpeg = {
.name = "s5p-jpeg",
.id = 0,
.num_resources = ARRAY_SIZE(s5p_jpeg_resource),
.resource = s5p_jpeg_resource,
.dev = {
.dma_mask = &samsung_device_dma_mask,
.coherent_dma_mask = DMA_BIT_MASK(32),
},
};
#endif /* CONFIG_S5P_DEV_JPEG */
/* FIMD0 */ /* FIMD0 */
#ifdef CONFIG_S5P_DEV_FIMD0 #ifdef CONFIG_S5P_DEV_FIMD0
...@@ -758,7 +805,7 @@ struct platform_device s3c_device_cfcon = { ...@@ -758,7 +805,7 @@ struct platform_device s3c_device_cfcon = {
.resource = s3c_cfcon_resource, .resource = s3c_cfcon_resource,
}; };
void s3c_ide_set_platdata(struct s3c_ide_platdata *pdata) void __init s3c_ide_set_platdata(struct s3c_ide_platdata *pdata)
{ {
s3c_set_platdata(pdata, sizeof(struct s3c_ide_platdata), s3c_set_platdata(pdata, sizeof(struct s3c_ide_platdata),
&s3c_device_cfcon); &s3c_device_cfcon);
...@@ -876,7 +923,7 @@ struct platform_device s5p_device_mfc_r = { ...@@ -876,7 +923,7 @@ struct platform_device s5p_device_mfc_r = {
#ifdef CONFIG_S5P_DEV_CSIS0 #ifdef CONFIG_S5P_DEV_CSIS0
static struct resource s5p_mipi_csis0_resource[] = { static struct resource s5p_mipi_csis0_resource[] = {
[0] = DEFINE_RES_MEM(S5P_PA_MIPI_CSIS0, SZ_4K), [0] = DEFINE_RES_MEM(S5P_PA_MIPI_CSIS0, SZ_16K),
[1] = DEFINE_RES_IRQ(IRQ_MIPI_CSIS0), [1] = DEFINE_RES_IRQ(IRQ_MIPI_CSIS0),
}; };
...@@ -890,7 +937,7 @@ struct platform_device s5p_device_mipi_csis0 = { ...@@ -890,7 +937,7 @@ struct platform_device s5p_device_mipi_csis0 = {
#ifdef CONFIG_S5P_DEV_CSIS1 #ifdef CONFIG_S5P_DEV_CSIS1
static struct resource s5p_mipi_csis1_resource[] = { static struct resource s5p_mipi_csis1_resource[] = {
[0] = DEFINE_RES_MEM(S5P_PA_MIPI_CSIS1, SZ_4K), [0] = DEFINE_RES_MEM(S5P_PA_MIPI_CSIS1, SZ_16K),
[1] = DEFINE_RES_IRQ(IRQ_MIPI_CSIS1), [1] = DEFINE_RES_IRQ(IRQ_MIPI_CSIS1),
}; };
...@@ -1038,7 +1085,7 @@ struct platform_device s3c64xx_device_onenand1 = { ...@@ -1038,7 +1085,7 @@ struct platform_device s3c64xx_device_onenand1 = {
.resource = s3c64xx_onenand1_resources, .resource = s3c64xx_onenand1_resources,
}; };
void s3c64xx_onenand1_set_platdata(struct onenand_platform_data *pdata) void __init s3c64xx_onenand1_set_platdata(struct onenand_platform_data *pdata)
{ {
s3c_set_platdata(pdata, sizeof(struct onenand_platform_data), s3c_set_platdata(pdata, sizeof(struct onenand_platform_data),
&s3c64xx_device_onenand1); &s3c64xx_device_onenand1);
...@@ -1412,6 +1459,19 @@ struct platform_device s3c_device_usb_hsotg = { ...@@ -1412,6 +1459,19 @@ struct platform_device s3c_device_usb_hsotg = {
.coherent_dma_mask = DMA_BIT_MASK(32), .coherent_dma_mask = DMA_BIT_MASK(32),
}, },
}; };
void __init s3c_hsotg_set_platdata(struct s3c_hsotg_plat *pd)
{
struct s3c_hsotg_plat *npd;
npd = s3c_set_platdata(pd, sizeof(struct s3c_hsotg_plat),
&s3c_device_usb_hsotg);
if (!npd->phy_init)
npd->phy_init = s5p_usb_phy_init;
if (!npd->phy_exit)
npd->phy_exit = s5p_usb_phy_exit;
}
#endif /* CONFIG_S3C_DEV_USB_HSOTG */ #endif /* CONFIG_S3C_DEV_USB_HSOTG */
/* USB High Spped 2.0 Device (Gadget) */ /* USB High Spped 2.0 Device (Gadget) */
......
...@@ -79,6 +79,8 @@ extern struct platform_device s5p_device_fimc1; ...@@ -79,6 +79,8 @@ extern struct platform_device s5p_device_fimc1;
extern struct platform_device s5p_device_fimc2; extern struct platform_device s5p_device_fimc2;
extern struct platform_device s5p_device_fimc3; extern struct platform_device s5p_device_fimc3;
extern struct platform_device s5p_device_fimc_md; extern struct platform_device s5p_device_fimc_md;
extern struct platform_device s5p_device_jpeg;
extern struct platform_device s5p_device_g2d;
extern struct platform_device s5p_device_fimd0; extern struct platform_device s5p_device_fimd0;
extern struct platform_device s5p_device_hdmi; extern struct platform_device s5p_device_hdmi;
extern struct platform_device s5p_device_i2c_hdmiphy; extern struct platform_device s5p_device_i2c_hdmiphy;
......
...@@ -25,8 +25,9 @@ ...@@ -25,8 +25,9 @@
#define S3C_HSOTG_PHYREG(x) ((x) + S3C_VA_USB_HSPHY) #define S3C_HSOTG_PHYREG(x) ((x) + S3C_VA_USB_HSPHY)
#define S3C_PHYPWR S3C_HSOTG_PHYREG(0x00) #define S3C_PHYPWR S3C_HSOTG_PHYREG(0x00)
#define SRC_PHYPWR_OTG_DISABLE (1 << 4) #define S3C_PHYPWR_NORMAL_MASK (0x19 << 0)
#define SRC_PHYPWR_ANALOG_POWERDOWN (1 << 3) #define S3C_PHYPWR_OTG_DISABLE (1 << 4)
#define S3C_PHYPWR_ANALOG_POWERDOWN (1 << 3)
#define SRC_PHYPWR_FORCE_SUSPEND (1 << 1) #define SRC_PHYPWR_FORCE_SUSPEND (1 << 1)
#define S3C_PHYCLK S3C_HSOTG_PHYREG(0x04) #define S3C_PHYCLK S3C_HSOTG_PHYREG(0x04)
...@@ -42,7 +43,7 @@ ...@@ -42,7 +43,7 @@
#define S3C_RSTCON S3C_HSOTG_PHYREG(0x08) #define S3C_RSTCON S3C_HSOTG_PHYREG(0x08)
#define S3C_RSTCON_PHYCLK (1 << 2) #define S3C_RSTCON_PHYCLK (1 << 2)
#define S3C_RSTCON_HCLK (1 << 2) #define S3C_RSTCON_HCLK (1 << 1)
#define S3C_RSTCON_PHY (1 << 0) #define S3C_RSTCON_PHY (1 << 0)
#define S3C_PHYTUNE S3C_HSOTG_PHYREG(0x20) #define S3C_PHYTUNE S3C_HSOTG_PHYREG(0x20)
......
...@@ -26,4 +26,9 @@ enum s3c_hsotg_dmamode { ...@@ -26,4 +26,9 @@ enum s3c_hsotg_dmamode {
struct s3c_hsotg_plat { struct s3c_hsotg_plat {
enum s3c_hsotg_dmamode dma; enum s3c_hsotg_dmamode dma;
unsigned int is_osc : 1; unsigned int is_osc : 1;
int (*phy_init)(struct platform_device *pdev, int type);
int (*phy_exit)(struct platform_device *pdev, int type);
}; };
extern void s3c_hsotg_set_platdata(struct s3c_hsotg_plat *pd);
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment