Commit 2c837a8a authored by Rama Kiran Kumar Indrakanti's avatar Rama Kiran Kumar Indrakanti Committed by Greg Kroah-Hartman

sc16is7xx: spi interface is added

spi interface for sc16is7xx is added along with Kconfig flag
to enable spi or i2c, thus in a instance we can have either
spi or i2c or both, in sync to the hw.
Signed-off-by: default avatarRama Kiran Kumar Indrakanti <indrakanti_ram@hotmail.com>
Signed-off-by: default avatarJakub Kicinski <kubakici@wp.pl>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent 34d2e458
......@@ -1179,15 +1179,42 @@ config SERIAL_SCCNXP_CONSOLE
help
Support for console on SCCNXP serial ports.
config SERIAL_SC16IS7XX_CORE
tristate
config SERIAL_SC16IS7XX
tristate "SC16IS7xx serial support"
depends on I2C
select SERIAL_CORE
select REGMAP_I2C if I2C
help
This selects support for SC16IS7xx serial ports.
Supported ICs are SC16IS740, SC16IS741, SC16IS750, SC16IS752,
SC16IS760 and SC16IS762.
tristate "SC16IS7xx serial support"
select SERIAL_CORE
depends on I2C || SPI_MASTER
help
This selects support for SC16IS7xx serial ports.
Supported ICs are SC16IS740, SC16IS741, SC16IS750, SC16IS752,
SC16IS760 and SC16IS762. Select supported buses using options below.
config SERIAL_SC16IS7XX_I2C
bool "SC16IS7xx for I2C interface"
depends on SERIAL_SC16IS7XX
depends on I2C
select SERIAL_SC16IS7XX_CORE if SERIAL_SC16IS7XX
select REGMAP_I2C if I2C
default y
help
Enable SC16IS7xx driver on I2C bus,
If required say y, and say n to i2c if not required,
Enabled by default to support oldconfig.
You must select at least one bus for the driver to be built.
config SERIAL_SC16IS7XX_SPI
bool "SC16IS7xx for spi interface"
depends on SERIAL_SC16IS7XX
depends on SPI_MASTER
select SERIAL_SC16IS7XX_CORE if SERIAL_SC16IS7XX
select REGMAP_SPI if SPI_MASTER
help
Enable SC16IS7xx driver on SPI bus,
If required say y, and say n to spi if not required,
This is additional support to exsisting driver.
You must select at least one bus for the driver to be built.
config SERIAL_BFIN_SPORT
tristate "Blackfin SPORT emulate UART"
......
......@@ -53,7 +53,7 @@ obj-$(CONFIG_SERIAL_SB1250_DUART) += sb1250-duart.o
obj-$(CONFIG_ETRAX_SERIAL) += crisv10.o
obj-$(CONFIG_SERIAL_ETRAXFS) += etraxfs-uart.o
obj-$(CONFIG_SERIAL_SCCNXP) += sccnxp.o
obj-$(CONFIG_SERIAL_SC16IS7XX) += sc16is7xx.o
obj-$(CONFIG_SERIAL_SC16IS7XX_CORE) += sc16is7xx.o
obj-$(CONFIG_SERIAL_JSM) += jsm/
obj-$(CONFIG_SERIAL_TXX9) += serial_txx9.o
obj-$(CONFIG_SERIAL_VR41XX) += vr41xx_siu.o
......
......@@ -25,6 +25,7 @@
#include <linux/serial.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/spi/spi.h>
#include <linux/uaccess.h>
#define SC16IS7XX_NAME "sc16is7xx"
......@@ -1204,6 +1205,73 @@ static struct regmap_config regcfg = {
.precious_reg = sc16is7xx_regmap_precious,
};
#ifdef CONFIG_SERIAL_SC16IS7XX_SPI
static int sc16is7xx_spi_probe(struct spi_device *spi)
{
struct sc16is7xx_devtype *devtype;
unsigned long flags = 0;
struct regmap *regmap;
int ret;
/* Setup SPI bus */
spi->bits_per_word = 8;
/* only supports mode 0 on SC16IS762 */
spi->mode = spi->mode ? : SPI_MODE_0;
spi->max_speed_hz = spi->max_speed_hz ? : 15000000;
ret = spi_setup(spi);
if (ret)
return ret;
if (spi->dev.of_node) {
const struct of_device_id *of_id =
of_match_device(sc16is7xx_dt_ids, &spi->dev);
devtype = (struct sc16is7xx_devtype *)of_id->data;
} else {
const struct spi_device_id *id_entry = spi_get_device_id(spi);
devtype = (struct sc16is7xx_devtype *)id_entry->driver_data;
flags = IRQF_TRIGGER_FALLING;
}
regcfg.max_register = (0xf << SC16IS7XX_REG_SHIFT) |
(devtype->nr_uart - 1);
regmap = devm_regmap_init_spi(spi, &regcfg);
return sc16is7xx_probe(&spi->dev, devtype, regmap, spi->irq, flags);
}
static int sc16is7xx_spi_remove(struct spi_device *spi)
{
return sc16is7xx_remove(&spi->dev);
}
static const struct spi_device_id sc16is7xx_spi_id_table[] = {
{ "sc16is74x", (kernel_ulong_t)&sc16is74x_devtype, },
{ "sc16is750", (kernel_ulong_t)&sc16is750_devtype, },
{ "sc16is752", (kernel_ulong_t)&sc16is752_devtype, },
{ "sc16is760", (kernel_ulong_t)&sc16is760_devtype, },
{ "sc16is762", (kernel_ulong_t)&sc16is762_devtype, },
{ }
};
MODULE_DEVICE_TABLE(spi, sc16is7xx_spi_id_table);
static struct spi_driver sc16is7xx_spi_uart_driver = {
.driver = {
.name = SC16IS7XX_NAME,
.owner = THIS_MODULE,
.of_match_table = of_match_ptr(sc16is7xx_dt_ids),
},
.probe = sc16is7xx_spi_probe,
.remove = sc16is7xx_spi_remove,
.id_table = sc16is7xx_spi_id_table,
};
MODULE_ALIAS("spi:sc16is7xx");
#endif
#ifdef CONFIG_SERIAL_SC16IS7XX_I2C
static int sc16is7xx_i2c_probe(struct i2c_client *i2c,
const struct i2c_device_id *id)
{
......@@ -1253,8 +1321,43 @@ static struct i2c_driver sc16is7xx_i2c_uart_driver = {
.remove = sc16is7xx_i2c_remove,
.id_table = sc16is7xx_i2c_id_table,
};
module_i2c_driver(sc16is7xx_i2c_uart_driver);
MODULE_ALIAS("i2c:sc16is7xx");
#endif
static int __init sc16is7xx_init(void)
{
int ret = 0;
#ifdef CONFIG_SERIAL_SC16IS7XX_I2C
ret = i2c_add_driver(&sc16is7xx_i2c_uart_driver);
if (ret < 0) {
pr_err("failed to init sc16is7xx i2c --> %d\n", ret);
return ret;
}
#endif
#ifdef CONFIG_SERIAL_SC16IS7XX_SPI
ret = spi_register_driver(&sc16is7xx_spi_uart_driver);
if (ret < 0) {
pr_err("failed to init sc16is7xx spi --> %d\n", ret);
return ret;
}
#endif
return ret;
}
module_init(sc16is7xx_init);
static void __exit sc16is7xx_exit(void)
{
#ifdef CONFIG_SERIAL_SC16IS7XX_I2C
i2c_del_driver(&sc16is7xx_i2c_uart_driver);
#endif
#ifdef CONFIG_SERIAL_SC16IS7XX_SPI
spi_unregister_driver(&sc16is7xx_spi_uart_driver);
#endif
}
module_exit(sc16is7xx_exit);
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Jon Ringle <jringle@gridpoint.com>");
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment