Merge tag 'mvebu-dt-4.5-3' of git://git.infradead.org/linux-mvebu into next/dt

mvebu dt for 4.5 (part 3)

Add dts for the following boards:
- Zyxel NSA325
- PogoPlug series 4
Add GPU support for Dove
Update boolean property to wakeup source for isil

* tag 'mvebu-dt-4.5-3' of git://git.infradead.org/linux-mvebu:
  ARM: dts: armada: replace isil, irq2-can-wakeup-machine with wakeup-source property
  ARM: dts: enable GPU for SolidRun's Cubox
  ARM: dts: dove: add DT GPU support
  ARM: mvebu: kirkwood: add PogoPlug series 4 device tree
  ARM: mvebu: add kirkwood compatibles for cloudengine boards
  ARM: dts: kirkwood: Add DTS for Zyxel NSA325
Signed-off-by: Olof Johansson <olof@lixom.net>

Documentation/devicetree/bindings/arm/marvell,kirkwood.txt

@@ -24,6 +24,8 @@ board. Currently known boards are:
 "buffalo,lswxl"
 "buffalo,lsxhl"
 "buffalo,lsxl"
+"cloudengines,pogo02"
+"cloudengines,pogoplugv4"
 "dlink,dns-320"
 "dlink,dns-320-a1"
 "dlink,dns-325"

arch/arm/boot/dts/Makefile

@@ -204,12 +204,14 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
 	kirkwood-ns2mini.dtb \
 	kirkwood-nsa310.dtb \
 	kirkwood-nsa310a.dtb \
+	kirkwood-nsa325.dtb \
 	kirkwood-openblocks_a6.dtb \
 	kirkwood-openblocks_a7.dtb \
 	kirkwood-openrd-base.dtb \
 	kirkwood-openrd-client.dtb \
 	kirkwood-openrd-ultimate.dtb \
 	kirkwood-pogo_e02.dtb \
+	kirkwood-pogoplug-series-4.dtb \
 	kirkwood-rd88f6192.dtb \
 	kirkwood-rd88f6281-z0.dtb \
 	kirkwood-rd88f6281-a.dtb \

arch/arm/boot/dts/armada-370-netgear-rn102.dts

@@ -127,7 +127,7 @@ i2c@11000 {
 				isl12057: isl12057@68 {
 					compatible = "isil,isl12057";
 					reg = <0x68>;
-					isil,irq2-can-wakeup-machine;
+					wakeup-source;
 				};
 
 				g762: g762@3e {

arch/arm/boot/dts/armada-370-netgear-rn104.dts

@@ -133,7 +133,7 @@ i2c@11000 {
 				isl12057: isl12057@68 {
 					compatible = "isil,isl12057";
 					reg = <0x68>;
-					isil,irq2-can-wakeup-machine;
+					wakeup-source;
 				};
 
 				g762: g762@3e {

arch/arm/boot/dts/armada-xp-netgear-rn2120.dts

@@ -141,7 +141,7 @@ g751: g751@4c {
 				isl12057: isl12057@68 {
 					compatible = "isil,isl12057";
 					reg = <0x68>;
-					isil,irq2-can-wakeup-machine;
+					wakeup-source;
 				};
 			};
 

arch/arm/boot/dts/dove-cubox.dts

@@ -62,6 +62,10 @@ ir_recv: ir-receiver {
 		pinctrl-0 = <&pmx_gpio_19>;
 		pinctrl-names = "default";
 	};
+
+	gpu-subsystem {
+		status = "okay";
+	};
 };
 
 &uart0 { status = "okay"; };
@@ -74,6 +78,10 @@ &ethphy {
 	reg = <1>;
 };
 
+&gpu {
+	status = "okay";
+};
+
 &i2c0 {
 	status = "okay";
 	clock-frequency = <100000>;

arch/arm/boot/dts/dove.dtsi

@@ -33,6 +33,12 @@ l2: l2-cache {
 		marvell,tauros2-cache-features = <0>;
 	};
 
+	gpu-subsystem {
+		compatible = "marvell,dove-gpu-subsystem";
+		cores = <&gpu>;
+		status = "disabled";
+	};
+
 	i2c-mux {
 		compatible = "i2c-mux-pinctrl";
 		#address-cells = <1>;
@@ -782,6 +788,16 @@ crypto_sram: sa-sram@ffffe000 {
 				#address-cells = <1>;
 				#size-cells = <1>;
 			};
+
+			gpu: gpu@840000 {
+				clocks = <&divider_clk 1>;
+				clock-names = "core";
+				compatible = "vivante,gc";
+				interrupts = <48>;
+				power-domains = <&gpu_domain>;
+				reg = <0x840000 0x4000>;
+				status = "disabled";
+			};
 		};
 	};
 };

arch/arm/boot/dts/kirkwood-nsa325.dts

+/* Device tree file for the Zyxel NSA 325 NAS box.
+ *
+ * Copyright (c) 2015, Hans Ulli Kroll <ulli.kroll@googlemail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ *
+ * Based upon the board setup file created by Peter Schildmann
+ */
+
+/dts-v1/;
+
+#include "kirkwood-nsa3x0-common.dtsi"
+
+/ {
+	model = "ZyXEL NSA325";
+	compatible = "zyxel,nsa325", "marvell,kirkwood-88f6282", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &uart0;
+	};
+
+	mbus {
+		pcie-controller {
+			status = "okay";
+
+			pcie@1,0 {
+				status = "okay";
+			};
+		};
+	};
+
+	ocp@f1000000 {
+		pinctrl: pin-controller@10000 {
+			pinctrl-names = "default";
+
+			pmx_led_hdd2_green: pmx-led-hdd2-green {
+				marvell,pins = "mpp12";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_hdd2_red: pmx-led-hdd2-red {
+				marvell,pins = "mpp13";
+				marvell,function = "gpio";
+			};
+
+			pmx_mcu_data: pmx-mcu-data {
+				marvell,pins = "mpp14";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_usb_green: pmx-led-usb-green {
+				marvell,pins = "mpp15";
+				marvell,function = "gpio";
+			};
+
+			pmx_mcu_clk: pmx-mcu-clk {
+				marvell,pins = "mpp16";
+				marvell,function = "gpio";
+			};
+
+			pmx_mcu_act: pmx-mcu-act {
+				marvell,pins = "mpp17";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_sys_green: pmx-led-sys-green {
+				marvell,pins = "mpp28";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_sys_orange: pmx-led-sys-orange {
+				marvell,pins = "mpp29";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_hdd1_green: pmx-led-hdd1-green {
+				marvell,pins = "mpp41";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_hdd1_red: pmx-led-hdd1-red {
+				marvell,pins = "mpp42";
+				marvell,function = "gpio";
+			};
+
+			pmx_htp: pmx-htp {
+				marvell,pins = "mpp43";
+				marvell,function = "gpio";
+			};
+
+			/*
+			 * Buzzer needs to be switched at around 1kHz so is
+			 * not compatible with the gpio-beeper driver.
+			 */
+			pmx_buzzer: pmx-buzzer {
+				marvell,pins = "mpp44";
+				marvell,function = "gpio";
+			};
+
+			pmx_vid_b1: pmx-vid-b1 {
+				marvell,pins = "mpp45";
+				marvell,function = "gpio";
+			};
+
+			pmx_power_resume_data: pmx-power-resume-data {
+				marvell,pins = "mpp47";
+				marvell,function = "gpio";
+			};
+
+			pmx_power_resume_clk: pmx-power-resume-clk {
+				marvell,pins = "mpp49";
+				marvell,function = "gpio";
+			};
+
+			pmx_pwr_sata1: pmx-pwr-sata1 {
+				marvell,pins = "mpp47";
+				marvell,function = "gpio";
+			};
+		};
+
+		/* This board uses the pcf8563 RTC instead of the SoC RTC */
+		rtc@10300 {
+			status = "disabled";
+		};
+
+		i2c@11000 {
+			status = "okay";
+
+			pcf8563: pcf8563@51 {
+				compatible = "nxp,pcf8563";
+				reg = <0x51>;
+			};
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_pwr_sata1>;
+		pinctrl-names = "default";
+
+		usb0_power: regulator@1 {
+			enable-active-high;
+		};
+
+		sata1_power: regulator@2 {
+			compatible = "regulator-fixed";
+			reg = <2>;
+			regulator-name = "SATA1 Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			regulator-always-on;
+			regulator-boot-on;
+			enable-active-high;
+			gpio = <&gpio1 15 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&pmx_led_hdd2_green &pmx_led_hdd2_red
+			     &pmx_led_usb_green
+			     &pmx_led_sys_green &pmx_led_sys_orange
+			     &pmx_led_copy_green &pmx_led_copy_red
+			     &pmx_led_hdd1_green &pmx_led_hdd1_red>;
+		pinctrl-names = "default";
+
+		green-sys {
+			label = "nsa325:green:sys";
+			gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
+		};
+		orange-sys {
+			label = "nsa325:orange:sys";
+			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+		};
+		green-hdd1 {
+			label = "nsa325:green:hdd1";
+			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+		};
+		red-hdd1 {
+			label = "nsa325:red:hdd1";
+			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+		};
+		green-hdd2 {
+			label = "nsa325:green:hdd2";
+			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+		};
+		red-hdd2 {
+			label = "nsa325:red:hdd2";
+			gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+		};
+		green-usb {
+			label = "nsa325:green:usb";
+			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
+		};
+		green-copy {
+			label = "nsa325:green:copy";
+			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+		};
+		red-copy {
+			label = "nsa325:red:copy";
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+		};
+
+	/* The following pins are currently not assigned to a driver,
+	   some of them should be configured as inputs.
+	pinctrl-0 = <&pmx_mcu_data &pmx_mcu_clk &pmx_mcu_act
+		     &pmx_htp &pmx_vid_b1
+		     &pmx_power_resume_data &pmx_power_resume_clk>; */
+	};
+
+
+};
+
+&mdio {
+	status = "okay";
+	ethphy0: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
+

arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts

+/*
+ * kirkwood-pogoplug-series-4.dts - Device tree file for PogoPlug Series 4
+ * inspired by the board files made by Kevin Mihelich for ArchLinux,
+ * and their DTS file.
+ *
+ * Copyright (C) 2015 Linus Walleij <linus.walleij@linaro.org>
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6192.dtsi"
+#include <dt-bindings/input/linux-event-codes.h>
+
+/ {
+	model = "Cloud Engines PogoPlug Series 4";
+	compatible = "cloudengines,pogoplugv4", "marvell,kirkwood-88f6192",
+		     "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>;
+	};
+
+	chosen {
+		stdout-path = "uart0:115200n8";
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_button_eject>;
+		pinctrl-names = "default";
+
+		button@1 {
+			debounce_interval = <50>;
+			wakeup-source;
+			linux,code = <KEY_EJECTCD>;
+			label = "Eject Button";
+			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&pmx_led_green &pmx_led_red>;
+		pinctrl-names = "default";
+
+		health {
+			label = "pogoplugv4:green:health";
+			gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+		fault {
+			label = "pogoplugv4:red:fault";
+			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&pinctrl {
+	pmx_sata0: pmx-sata0 {
+		marvell,pins = "mpp21";
+		marvell,function = "sata0";
+	};
+
+	pmx_sata1: pmx-sata1 {
+		marvell,pins = "mpp20";
+		marvell,function = "sata1";
+	};
+
+	pmx_sdio_cd: pmx-sdio-cd {
+		marvell,pins = "mpp27";
+		marvell,function = "gpio";
+	};
+
+	pmx_sdio_wp: pmx-sdio-wp {
+		marvell,pins = "mpp28";
+		marvell,function = "gpio";
+	};
+
+	pmx_button_eject: pmx-button-eject {
+		marvell,pins = "mpp29";
+		marvell,function = "gpio";
+	};
+
+	pmx_led_green: pmx-led-green {
+		marvell,pins = "mpp22";
+		marvell,function = "gpio";
+	};
+
+	pmx_led_red: pmx-led-red {
+		marvell,pins = "mpp24";
+		marvell,function = "gpio";
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+/*
+ * This PCIE controller has a USB 3.0 XHCI controller at 1,0
+ */
+&pciec {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+	pinctrl-0 = <&pmx_sata0 &pmx_sata1>;
+	pinctrl-names = "default";
+	nr-ports = <1>;
+};
+
+&sdio {
+	status = "okay";
+	pinctrl-0 = <&pmx_sdio &pmx_sdio_cd &pmx_sdio_wp>;
+	pinctrl-names = "default";
+	cd-gpios = <&gpio0 27 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
+};
+
+&nand {
+	/* 128 MiB of NAND flash */
+	chip-delay = <40>;
+	status = "okay";
+	partitions {
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "u-boot";
+			reg = <0x00000000 0x200000>;
+			read-only;
+		};
+
+		partition@200000 {
+			label = "uImage";
+			reg = <0x00200000 0x300000>;
+		};
+
+		partition@500000 {
+			label = "uImage2";
+			reg = <0x00500000 0x300000>;
+		};
+
+		partition@800000 {
+			label = "failsafe";
+			reg = <0x00800000 0x800000>;
+		};
+
+		partition@1000000 {
+			label = "root";
+			reg = <0x01000000 0x7000000>;
+		};
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};