Blackfin arch: add support for Blackfin latest processor family BF51x

Signed-off-by: Bryan Wu <cooloney@kernel.org>

arch/blackfin/Kconfig

@@ -77,6 +77,26 @@ choice
 	prompt "CPU"
 	default BF533
 
+config BF512
+	bool "BF512"
+	help
+	  BF512 Processor Support.
+
+config BF514
+	bool "BF514"
+	help
+	  BF514 Processor Support.
+
+config BF516
+	bool "BF516"
+	help
+	  BF516 Processor Support.
+
+config BF518
+	bool "BF518"
+	help
+	  BF518 Processor Support.
+
 config BF522
 	bool "BF522"
 	help
@@ -181,27 +201,27 @@ endchoice
 
 config BF_REV_MIN
 	int
-	default 0 if (BF52x || BF54x)
+	default 0 if (BF51x || BF52x || BF54x)
 	default 2 if (BF537 || BF536 || BF534)
 	default 3 if (BF561 ||BF533 || BF532 || BF531)
 	default 4 if (BF538 || BF539)
 
 config BF_REV_MAX
 	int
-	default 2 if (BF52x || BF54x)
+	default 2 if (BF51x || BF52x || BF54x)
 	default 3 if (BF537 || BF536 || BF534)
-	default 5 if (BF561|| BF538 || BF539)
+	default 5 if (BF561 || BF538 || BF539)
 	default 6 if (BF533 || BF532 || BF531)
 
 choice
 	prompt "Silicon Rev"
-	default BF_REV_0_1 if (BF52x || BF54x)
+	default BF_REV_0_1 if (BF51x || BF52x || BF54x)
 	default BF_REV_0_2 if (BF534 || BF536 || BF537)
 	default BF_REV_0_3 if (BF531 || BF532 || BF533 || BF561)
 
 config BF_REV_0_0
 	bool "0.0"
-	depends on (BF52x || BF54x)
+	depends on (BF51x || BF52x || BF54x)
 
 config BF_REV_0_1
 	bool "0.1"
@@ -235,6 +255,11 @@ config BF_REV_NONE
 
 endchoice
 
+config BF51x
+	bool
+	depends on (BF512 || BF514 || BF516 || BF518)
+	default y
+
 config BF52x
 	bool
 	depends on (BF522 || BF523 || BF524 || BF525 || BF526 || BF527)
@@ -282,6 +307,7 @@ config MEM_MT48LC32M16A2TG_75
 	depends on (BFIN527_EZKIT || BFIN532_IP0X || BLACKSTAMP || BFIN526_EZBRD)
 	default y
 
+source "arch/blackfin/mach-bf518/Kconfig"
 source "arch/blackfin/mach-bf527/Kconfig"
 source "arch/blackfin/mach-bf533/Kconfig"
 source "arch/blackfin/mach-bf561/Kconfig"
@@ -330,7 +356,7 @@ config CLKIN_HZ
 	int "Frequency of the crystal on the board in Hz"
 	default "11059200" if BFIN533_STAMP
 	default "27000000" if BFIN533_EZKIT
-	default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT || H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD || BFIN538_EZKIT)
+	default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT || H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD || BFIN538_EZKIT || BFIN518F-EZBRD)
 	default "30000000" if BFIN561_EZKIT
 	default "24576000" if PNAV10
 	default "10000000" if BFIN532_IP0X
@@ -370,7 +396,7 @@ config VCO_MULT
 	default "22" if BFIN533_BLUETECHNIX_CM
 	default "20" if (BFIN537_BLUETECHNIX_CM || BFIN527_BLUETECHNIX_CM || BFIN561_BLUETECHNIX_CM)
 	default "20" if BFIN561_EZKIT
-	default "16" if (H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD)
+	default "16" if (H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD || BFIN518F_EZBRD)
 	help
 	  This controls the frequency of the on-chip PLL. This can be between 1 and 64.
 	  PLL Frequency = (Crystal Frequency) * (this setting)
@@ -432,6 +458,10 @@ config MAX_MEM_SIZE
 #
 config MAX_VCO_HZ
 	int
+	default 400000000 if BF512
+	default 400000000 if BF514
+	default 400000000 if BF516
+	default 400000000 if BF518
 	default 600000000 if BF522
 	default 400000000 if BF523
 	default 400000000 if BF524
@@ -1025,7 +1055,7 @@ comment "Possible Suspend Mem / Hibernate Wake-Up Sources"
 
 config PM_BFIN_WAKE_PH6
 	bool "Allow Wake-Up from on-chip PHY or PH6 GP"
-	depends on PM && (BF52x || BF534 || BF536 || BF537)
+	depends on PM && (BF51x || BF52x || BF534 || BF536 || BF537)
 	default n
 	help
 	  Enable PHY and PH6 GP Wake-Up (Voltage Regulator Power-Up)

arch/blackfin/Makefile

@@ -21,6 +21,10 @@ KALLSYMS         += --symbol-prefix=_
 KBUILD_DEFCONFIG := BF537-STAMP_defconfig
 
 # setup the machine name and the machine dependent settings
+machine-$(CONFIG_BF512) := bf518
+machine-$(CONFIG_BF514) := bf518
+machine-$(CONFIG_BF516) := bf518
+machine-$(CONFIG_BF518) := bf518
 machine-$(CONFIG_BF522) := bf527
 machine-$(CONFIG_BF523) := bf527
 machine-$(CONFIG_BF524) := bf527
@@ -44,6 +48,10 @@ machine-$(CONFIG_BF561) := bf561
 MACHINE := $(machine-y)
 export MACHINE
 
+cpu-$(CONFIG_BF512) := bf512
+cpu-$(CONFIG_BF514) := bf514
+cpu-$(CONFIG_BF516) := bf516
+cpu-$(CONFIG_BF518) := bf518
 cpu-$(CONFIG_BF522) := bf522
 cpu-$(CONFIG_BF523) := bf523
 cpu-$(CONFIG_BF524) := bf524

arch/blackfin/include/asm/gpio.h

@@ -143,6 +143,57 @@
 #define PERIPHERAL_USAGE 1
 #define GPIO_USAGE 0
 
+#if defined(BF518_FAMILY)
+#define MAX_BLACKFIN_GPIOS 40
+
+#define	GPIO_PF0	0
+#define	GPIO_PF1	1
+#define	GPIO_PF2	2
+#define	GPIO_PF3	3
+#define	GPIO_PF4	4
+#define	GPIO_PF5	5
+#define	GPIO_PF6	6
+#define	GPIO_PF7	7
+#define	GPIO_PF8	8
+#define	GPIO_PF9	9
+#define	GPIO_PF10	10
+#define	GPIO_PF11	11
+#define	GPIO_PF12	12
+#define	GPIO_PF13	13
+#define	GPIO_PF14	14
+#define	GPIO_PF15	15
+#define	GPIO_PG0	16
+#define	GPIO_PG1	17
+#define	GPIO_PG2	18
+#define	GPIO_PG3	19
+#define	GPIO_PG4	20
+#define	GPIO_PG5	21
+#define	GPIO_PG6	22
+#define	GPIO_PG7	23
+#define	GPIO_PG8	24
+#define	GPIO_PG9	25
+#define	GPIO_PG10      	26
+#define	GPIO_PG11      	27
+#define	GPIO_PG12      	28
+#define	GPIO_PG13      	29
+#define	GPIO_PG14      	30
+#define	GPIO_PG15      	31
+#define	GPIO_PH0	32
+#define	GPIO_PH1	33
+#define	GPIO_PH2	34
+#define	GPIO_PH3	35
+#define	GPIO_PH4	36
+#define	GPIO_PH5	37
+#define	GPIO_PH6	38
+#define	GPIO_PH7	39
+
+#define PORT_F GPIO_PF0
+#define PORT_G GPIO_PG0
+#define PORT_H GPIO_PH0
+
+#endif
+
+
 #ifdef BF533_FAMILY
 #define MAX_BLACKFIN_GPIOS 16
 

arch/blackfin/kernel/bfin_gpio.c

@@ -125,7 +125,7 @@ static struct gpio_port_t *gpio_bankb[gpio_bank(MAX_BLACKFIN_GPIOS)] = {
 };
 #endif
 
-#if defined(BF527_FAMILY) || defined(BF537_FAMILY)
+#if defined(BF527_FAMILY) || defined(BF537_FAMILY) || defined(BF518_FAMILY)
 static struct gpio_port_t *gpio_bankb[gpio_bank(MAX_BLACKFIN_GPIOS)] = {
 	(struct gpio_port_t *) PORTFIO,
 	(struct gpio_port_t *) PORTGIO,
@@ -139,7 +139,7 @@ static unsigned short *port_fer[gpio_bank(MAX_BLACKFIN_GPIOS)] = {
 };
 #endif
 
-#ifdef BF527_FAMILY
+#if defined(BF527_FAMILY) || defined(BF518_FAMILY)
 static unsigned short *port_mux[gpio_bank(MAX_BLACKFIN_GPIOS)] = {
 	(unsigned short *) PORTF_MUX,
 	(unsigned short *) PORTG_MUX,
@@ -206,7 +206,7 @@ static unsigned int sic_iwr_irqs[gpio_bank(MAX_BLACKFIN_GPIOS)] = {IRQ_PROG_INTB
 static unsigned int sic_iwr_irqs[gpio_bank(MAX_BLACKFIN_GPIOS)] = {IRQ_PORTF_INTB};
 #endif
 
-#ifdef BF527_FAMILY
+#if defined(BF527_FAMILY) || defined(BF518_FAMILY)
 static unsigned int sic_iwr_irqs[gpio_bank(MAX_BLACKFIN_GPIOS)] = {IRQ_PORTF_INTB, IRQ_PORTG_INTB, IRQ_PORTH_INTB};
 #endif
 
@@ -268,7 +268,7 @@ static int cmp_label(unsigned short ident, const char *label)
 		return -EINVAL;
 }
 
-#if defined(BF527_FAMILY) || defined(BF537_FAMILY)
+#if defined(BF527_FAMILY) || defined(BF537_FAMILY) || defined(BF518_FAMILY)
 static void port_setup(unsigned gpio, unsigned short usage)
 {
 	if (!check_gpio(gpio)) {
@@ -383,7 +383,7 @@ inline u16 get_portmux(unsigned short portno)
 
 	return (pmux >> (2 * gpio_sub_n(portno)) & 0x3);
 }
-#elif defined(BF527_FAMILY)
+#elif defined(BF527_FAMILY) || defined(BF518_FAMILY)
 inline void portmux_setup(unsigned short portno, unsigned short function)
 {
 	u16 pmux, ident = P_IDENT(portno);
@@ -683,7 +683,7 @@ u32 bfin_pm_standby_setup(void)
 		gpio_bankb[bank]->maskb = 0;
 
 		if (mask) {
-#if defined(BF527_FAMILY) || defined(BF537_FAMILY)
+#if defined(BF527_FAMILY) || defined(BF537_FAMILY) || defined(BF518_FAMILY)
 			gpio_bank_saved[bank].fer   = *port_fer[bank];
 #endif
 			gpio_bank_saved[bank].inen  = gpio_bankb[bank]->inen;
@@ -728,7 +728,7 @@ void bfin_pm_standby_restore(void)
 		bank = gpio_bank(i);
 
 		if (mask) {
-#if defined(BF527_FAMILY) || defined(BF537_FAMILY)
+#if defined(BF527_FAMILY) || defined(BF537_FAMILY) || defined(BF518_FAMILY)
 			*port_fer[bank]   	= gpio_bank_saved[bank].fer;
 #endif
 			gpio_bankb[bank]->inen  = gpio_bank_saved[bank].inen;
@@ -754,9 +754,9 @@ void bfin_gpio_pm_hibernate_suspend(void)
 	for (i = 0; i < MAX_BLACKFIN_GPIOS; i += GPIO_BANKSIZE) {
 		bank = gpio_bank(i);
 
-#if defined(BF527_FAMILY) || defined(BF537_FAMILY)
+#if defined(BF527_FAMILY) || defined(BF537_FAMILY) || defined(BF518_FAMILY)
 			gpio_bank_saved[bank].fer   = *port_fer[bank];
-#ifdef BF527_FAMILY
+#if defined(BF527_FAMILY) || defined(BF518_FAMILY)
 			gpio_bank_saved[bank].mux   = *port_mux[bank];
 #else
 			if (bank == 0)
@@ -782,8 +782,8 @@ void bfin_gpio_pm_hibernate_restore(void)
 	for (i = 0; i < MAX_BLACKFIN_GPIOS; i += GPIO_BANKSIZE) {
 			bank = gpio_bank(i);
 
-#if defined(BF527_FAMILY) || defined(BF537_FAMILY)
-#ifdef BF527_FAMILY
+#if defined(BF527_FAMILY) || defined(BF537_FAMILY) || defined(BF518_FAMILY)
+#if defined(BF527_FAMILY) || defined(BF518_FAMILY)
 			*port_mux[bank] = gpio_bank_saved[bank].mux;
 #else
 			if (bank == 0)

arch/blackfin/mach-bf518/Kconfig

+if (BF51x)
+
+source "arch/blackfin/mach-bf518/boards/Kconfig"
+
+menu "BF518 Specific Configuration"
+
+comment "Alternative Multiplexing Scheme"
+
+choice
+	prompt "SPORT0"
+	default BF518_SPORT0_PORTG
+	help
+	  Select PORT used for SPORT0. See Hardware Reference Manual
+
+config BF518_SPORT0_PORTF
+	bool "PORT F"
+	help
+	  PORT F
+
+config BF518_SPORT0_PORTG
+	bool "PORT G"
+	help
+	  PORT G
+endchoice
+
+choice
+	prompt "SPORT0 TSCLK Location"
+	depends on BF518_SPORT0_PORTG
+	default BF518_SPORT0_TSCLK_PG10
+	help
+	  Select PIN used for SPORT0_TSCLK. See Hardware Reference Manual
+
+config BF518_SPORT0_TSCLK_PG10
+	bool "PORT PG10"
+	help
+	  PORT PG10
+
+config BF518_SPORT0_TSCLK_PG14
+	bool "PORT PG14"
+	help
+	  PORT PG14
+endchoice
+
+choice
+	prompt "UART1"
+	default BF518_UART1_PORTF
+	help
+	  Select PORT used for UART1. See Hardware Reference Manual
+
+config BF518_UART1_PORTF
+	bool "PORT F"
+	help
+	  PORT F
+
+config BF518_UART1_PORTG
+	bool "PORT G"
+	help
+	  PORT G
+endchoice
+
+comment "Interrupt Priority Assignment"
+menu "Priority"
+
+config IRQ_PLL_WAKEUP
+	int "IRQ_PLL_WAKEUP"
+	default 7
+config IRQ_DMA0_ERROR
+	int "IRQ_DMA0_ERROR"
+	default 7
+config IRQ_DMAR0_BLK
+	int "IRQ_DMAR0_BLK"
+	default 7
+config IRQ_DMAR1_BLK
+	int "IRQ_DMAR1_BLK"
+	default 7
+config IRQ_DMAR0_OVR
+	int "IRQ_DMAR0_OVR"
+	default 7
+config IRQ_DMAR1_OVR
+	int "IRQ_DMAR1_OVR"
+	default 7
+config IRQ_PPI_ERROR
+	int "IRQ_PPI_ERROR"
+	default 7
+config IRQ_MAC_ERROR
+	int "IRQ_MAC_ERROR"
+	default 7
+config IRQ_SPORT0_ERROR
+	int "IRQ_SPORT0_ERROR"
+	default 7
+config IRQ_SPORT1_ERROR
+	int "IRQ_SPORT1_ERROR"
+	default 7
+config IRQ_PTP_ERROR
+	int "IRQ_PTP_ERROR"
+	default 7
+config IRQ_UART0_ERROR
+	int "IRQ_UART0_ERROR"
+	default 7
+config IRQ_UART1_ERROR
+	int "IRQ_UART1_ERROR"
+	default 7
+config IRQ_RTC
+	int "IRQ_RTC"
+	default 8
+config IRQ_PPI
+	int "IRQ_PPI"
+	default 8
+config IRQ_SPORT0_RX
+	int "IRQ_SPORT0_RX"
+	default 9
+config IRQ_SPORT0_TX
+	int "IRQ_SPORT0_TX"
+	default 9
+config IRQ_SPORT1_RX
+	int "IRQ_SPORT1_RX"
+	default 9
+config IRQ_SPORT1_TX
+	int "IRQ_SPORT1_TX"
+	default 9
+config IRQ_TWI
+	int "IRQ_TWI"
+	default 10
+config IRQ_SPI0
+	int "IRQ_SPI"
+	default 10
+config IRQ_UART0_RX
+	int "IRQ_UART0_RX"
+	default 10
+config IRQ_UART0_TX
+	int "IRQ_UART0_TX"
+	default 10
+config IRQ_UART1_RX
+	int "IRQ_UART1_RX"
+	default 10
+config IRQ_UART1_TX
+	int "IRQ_UART1_TX"
+	default 10
+config IRQ_OPTSEC
+	int "IRQ_OPTSEC"
+	default 11
+config IRQ_CNT
+	int "IRQ_CNT"
+	default 11
+config IRQ_MAC_RX
+	int "IRQ_MAC_RX"
+	default 11
+config IRQ_PORTH_INTA
+	int "IRQ_PORTH_INTA"
+	default 11
+config IRQ_MAC_TX
+	int "IRQ_MAC_TX/NFC"
+	default 11
+config IRQ_PORTH_INTB
+	int "IRQ_PORTH_INTB"
+	default 11
+config IRQ_TMR0
+	int "IRQ_TMR0"
+	default 12
+config IRQ_TMR1
+	int "IRQ_TMR1"
+	default 12
+config IRQ_TMR2
+	int "IRQ_TMR2"
+	default 12
+config IRQ_TMR3
+	int "IRQ_TMR3"
+	default 12
+config IRQ_TMR4
+	int "IRQ_TMR4"
+	default 12
+config IRQ_TMR5
+	int "IRQ_TMR5"
+	default 12
+config IRQ_TMR6
+	int "IRQ_TMR6"
+	default 12
+config IRQ_TMR7
+	int "IRQ_TMR7"
+	default 12
+config IRQ_PORTG_INTA
+	int "IRQ_PORTG_INTA"
+	default 12
+config IRQ_PORTG_INTB
+	int "IRQ_PORTG_INTB"
+	default 12
+config IRQ_MEM_DMA0
+	int "IRQ_MEM_DMA0"
+	default 13
+config IRQ_MEM_DMA1
+	int "IRQ_MEM_DMA1"
+	default 13
+config IRQ_WATCH
+	int "IRQ_WATCH"
+	default 13
+config IRQ_PORTF_INTA
+	int "IRQ_PORTF_INTA"
+	default 13
+config IRQ_PORTF_INTB
+	int "IRQ_PORTF_INTB"
+	default 13
+config IRQ_SPI0_ERROR
+	int "IRQ_SPI0_ERROR"
+	default 7
+config IRQ_SPI1_ERROR
+	int "IRQ_SPI1_ERROR"
+	default 7
+config IRQ_RSI_INT0
+	int "IRQ_RSI_INT0"
+	default 7
+config IRQ_RSI_INT1
+	int "IRQ_RSI_INT1"
+	default 7
+config IRQ_PWM_TRIP
+	int "IRQ_PWM_TRIP"
+	default 10
+config IRQ_PWM_SYNC
+	int "IRQ_PWM_SYNC"
+	default 10
+config IRQ_PTP_STAT
+	int "IRQ_PTP_STAT"
+	default 10
+
+	help
+	  Enter the priority numbers between 7-13 ONLY.  Others are Reserved.
+	  This applies to all the above.  It is not recommended to assign the
+	  highest priority number 7 to UART or any other device.
+
+endmenu
+
+endmenu
+
+endif

arch/blackfin/mach-bf518/Makefile

+#
+# arch/blackfin/mach-bf518/Makefile
+#
+
+extra-y := head.o
+
+obj-y := ints-priority.o dma.o

arch/blackfin/mach-bf518/boards/Kconfig

+choice
+	prompt "System type"
+	default BFIN518F_EZBRD
+	help
+	  Select your board!
+
+config BFIN518F_EZBRD
+	bool "BF518F-EZBRD"
+	help
+	  BF518-EZBRD board support.
+
+endchoice

arch/blackfin/mach-bf518/boards/Makefile

+#
+# arch/blackfin/mach-bf518/boards/Makefile
+#
+
+obj-$(CONFIG_BFIN518F_EZBRD)            += ezbrd.o

arch/blackfin/mach-bf518/dma.c

+/*
+ * File:         arch/blackfin/mach-bf518/dma.c
+ * Based on:
+ * Author:       Bryan Wu <cooloney@kernel.org>
+ *
+ * Created:
+ * Description:  This file contains the simple DMA Implementation for Blackfin
+ *
+ * Modified:
+ *               Copyright 2004-2008 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+#include <linux/module.h>
+
+#include <asm/blackfin.h>
+#include <asm/dma.h>
+
+struct dma_register *dma_io_base_addr[MAX_BLACKFIN_DMA_CHANNEL] = {
+	(struct dma_register *) DMA0_NEXT_DESC_PTR,
+	(struct dma_register *) DMA1_NEXT_DESC_PTR,
+	(struct dma_register *) DMA2_NEXT_DESC_PTR,
+	(struct dma_register *) DMA3_NEXT_DESC_PTR,
+	(struct dma_register *) DMA4_NEXT_DESC_PTR,
+	(struct dma_register *) DMA5_NEXT_DESC_PTR,
+	(struct dma_register *) DMA6_NEXT_DESC_PTR,
+	(struct dma_register *) DMA7_NEXT_DESC_PTR,
+	(struct dma_register *) DMA8_NEXT_DESC_PTR,
+	(struct dma_register *) DMA9_NEXT_DESC_PTR,
+	(struct dma_register *) DMA10_NEXT_DESC_PTR,
+	(struct dma_register *) DMA11_NEXT_DESC_PTR,
+	(struct dma_register *) MDMA_S0_NEXT_DESC_PTR,
+	(struct dma_register *) MDMA_D0_NEXT_DESC_PTR,
+	(struct dma_register *) MDMA_S1_NEXT_DESC_PTR,
+	(struct dma_register *) MDMA_D1_NEXT_DESC_PTR,
+};
+EXPORT_SYMBOL(dma_io_base_addr);
+
+int channel2irq(unsigned int channel)
+{
+	int ret_irq = -1;
+
+	switch (channel) {
+	case CH_PPI:
+		ret_irq = IRQ_PPI;
+		break;
+
+	case CH_EMAC_RX:
+		ret_irq = IRQ_MAC_RX;
+		break;
+
+	case CH_EMAC_TX:
+		ret_irq = IRQ_MAC_TX;
+		break;
+
+	case CH_UART1_RX:
+		ret_irq = IRQ_UART1_RX;
+		break;
+
+	case CH_UART1_TX:
+		ret_irq = IRQ_UART1_TX;
+		break;
+
+	case CH_SPORT0_RX:
+		ret_irq = IRQ_SPORT0_RX;
+		break;
+
+	case CH_SPORT0_TX:
+		ret_irq = IRQ_SPORT0_TX;
+		break;
+
+	case CH_SPORT1_RX:
+		ret_irq = IRQ_SPORT1_RX;
+		break;
+
+	case CH_SPORT1_TX:
+		ret_irq = IRQ_SPORT1_TX;
+		break;
+
+	case CH_SPI0:
+		ret_irq = IRQ_SPI0;
+		break;
+
+	case CH_UART0_RX:
+		ret_irq = IRQ_UART0_RX;
+		break;
+
+	case CH_UART0_TX:
+		ret_irq = IRQ_UART0_TX;
+		break;
+
+	case CH_MEM_STREAM0_SRC:
+	case CH_MEM_STREAM0_DEST:
+		ret_irq = IRQ_MEM_DMA0;
+		break;
+
+	case CH_MEM_STREAM1_SRC:
+	case CH_MEM_STREAM1_DEST:
+		ret_irq = IRQ_MEM_DMA1;
+		break;
+	}
+	return ret_irq;
+}

arch/blackfin/mach-bf518/head.S

+/*
+ * File:         arch/blackfin/mach-bf518/head.S
+ * Based on:     arch/blackfin/mach-bf527/head.S
+ * Author:       Bryan Wu <cooloney@kernel.org>
+ *
+ * Created:      2008
+ * Description:  Startup code for Blackfin BF51x
+ *
+ * Modified:
+ *               Copyright 2004-2008 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/linkage.h>
+#include <linux/init.h>
+#include <asm/blackfin.h>
+#ifdef CONFIG_BFIN_KERNEL_CLOCK
+#include <asm/mach-common/clocks.h>
+#include <asm/mach/mem_init.h>
+#endif
+
+.section .l1.text
+#ifdef CONFIG_BFIN_KERNEL_CLOCK
+ENTRY(_start_dma_code)
+
+	/* Enable PHY CLK buffer output */
+	p0.h = hi(VR_CTL);
+	p0.l = lo(VR_CTL);
+	r0.l = w[p0];
+	bitset(r0, 14);
+	w[p0] = r0.l;
+	ssync;
+
+	p0.h = hi(SIC_IWR0);
+	p0.l = lo(SIC_IWR0);
+	r0.l = 0x1;
+	r0.h = 0x0;
+	[p0] = r0;
+	ssync;
+
+	/*
+	 *  Set PLL_CTL
+	 *   - [14:09] = MSEL[5:0] : CLKIN / VCO multiplication factors
+	 *   - [8]     = BYPASS    : BYPASS the PLL, run CLKIN into CCLK/SCLK
+	 *   - [7]     = output delay (add 200ps of delay to mem signals)
+	 *   - [6]     = input delay (add 200ps of input delay to mem signals)
+	 *   - [5]     = PDWN      : 1=All Clocks off
+	 *   - [3]     = STOPCK    : 1=Core Clock off
+	 *   - [1]     = PLL_OFF   : 1=Disable Power to PLL
+	 *   - [0]     = DF        : 1=Pass CLKIN/2 to PLL / 0=Pass CLKIN to PLL
+	 *   all other bits set to zero
+	 */
+
+	p0.h = hi(PLL_LOCKCNT);
+	p0.l = lo(PLL_LOCKCNT);
+	r0 = 0x300(Z);
+	w[p0] = r0.l;
+	ssync;
+
+	P2.H = hi(EBIU_SDGCTL);
+	P2.L = lo(EBIU_SDGCTL);
+	R0 = [P2];
+	BITSET (R0, 24);
+	[P2] = R0;
+	ssync;
+
+	r0 = CONFIG_VCO_MULT & 63;       /* Load the VCO multiplier         */
+	r0 = r0 << 9;                    /* Shift it over,                  */
+	r1 = CLKIN_HALF;                 /* Do we need to divide CLKIN by 2?*/
+	r0 = r1 | r0;
+	r1 = PLL_BYPASS;                 /* Bypass the PLL?                 */
+	r1 = r1 << 8;                    /* Shift it over                   */
+	r0 = r1 | r0;                    /* add them all together           */
+#ifdef ANOMALY_05000265
+	BITSET(r0, 15);                  /* Add 250 mV of hysteresis to SPORT input pins */
+#endif
+
+	p0.h = hi(PLL_CTL);
+	p0.l = lo(PLL_CTL);              /* Load the address                */
+	cli r2;                          /* Disable interrupts              */
+	ssync;
+	w[p0] = r0.l;                    /* Set the value                   */
+	idle;                            /* Wait for the PLL to stablize    */
+	sti r2;                          /* Enable interrupts               */
+
+.Lcheck_again:
+	p0.h = hi(PLL_STAT);
+	p0.l = lo(PLL_STAT);
+	R0 = W[P0](Z);
+	CC = BITTST(R0,5);
+	if ! CC jump .Lcheck_again;
+
+	/* Configure SCLK & CCLK Dividers */
+	r0 = (CONFIG_CCLK_ACT_DIV | CONFIG_SCLK_DIV);
+	p0.h = hi(PLL_DIV);
+	p0.l = lo(PLL_DIV);
+	w[p0] = r0.l;
+	ssync;
+
+	p0.l = lo(EBIU_SDRRC);
+	p0.h = hi(EBIU_SDRRC);
+	r0 = mem_SDRRC;
+	w[p0] = r0.l;
+	ssync;
+
+	P2.H = hi(EBIU_SDGCTL);
+	P2.L = lo(EBIU_SDGCTL);
+	R0 = [P2];
+	BITCLR (R0, 24);
+	p0.h = hi(EBIU_SDSTAT);
+	p0.l = lo(EBIU_SDSTAT);
+	r2.l = w[p0];
+	cc = bittst(r2,3);
+	if !cc jump .Lskip;
+	NOP;
+	BITSET (R0, 23);
+.Lskip:
+	[P2] = R0;
+	SSYNC;
+
+	R0.L = lo(mem_SDGCTL);
+	R0.H = hi(mem_SDGCTL);
+	R1 = [p2];
+	R1 = R1 | R0;
+	[P2] = R1;
+	SSYNC;
+
+	RTS;
+ENDPROC(_start_dma_code)
+#endif /* CONFIG_BFIN_KERNEL_CLOCK */

arch/blackfin/mach-bf518/include/mach/anomaly.h

+/*
+ * File: include/asm-blackfin/mach-bf518/anomaly.h
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * Copyright (C) 2004-2008 Analog Devices Inc.
+ * Licensed under the GPL-2 or later.
+ */
+
+/* This file shoule be up to date with:
+ *  - ????
+ */
+
+#ifndef _MACH_ANOMALY_H_
+#define _MACH_ANOMALY_H_
+
+/* Multi-Issue Instruction with dsp32shiftimm in slot1 and P-reg Store in slot2 Not Supported */
+#define ANOMALY_05000074 (1)
+/* Rx.H Cannot Be Used to Access 16-bit System MMR Registers */
+#define ANOMALY_05000122 (1)
+/* False Hardware Error from an Access in the Shadow of a Conditional Branch */
+#define ANOMALY_05000245 (1)
+/* Sensitivity To Noise with Slow Input Edge Rates on External SPORT TX and RX Clocks */
+#define ANOMALY_05000265 (1)
+/* False Hardware Errors Caused by Fetches at the Boundary of Reserved Memory */
+#define ANOMALY_05000310 (1)
+/* PPI Underflow Error Goes Undetected in ITU-R 656 Mode */
+#define ANOMALY_05000366 (1)
+/* Lockbox SESR Firmware Does Not Save/Restore Full Context */
+#define ANOMALY_05000405 (1)
+/* Lockbox Firmware Memory Cleanup Routine Does not Clear Registers */
+#define ANOMALY_05000408 (1)
+/* Speculative Fetches Can Cause Undesired External FIFO Operations */
+#define ANOMALY_05000416 (1)
+/* TWI Fall Time (Tof) May Violate the Minimum I2C Specification */
+#define ANOMALY_05000421 (1)
+/* TWI Input Capacitance (Ci) May Violate the Maximum I2C Specification */
+#define ANOMALY_05000422 (1)
+/* Speculative Fetches of Indirect-Pointer Instructions Can Cause False Hardware Errors */
+#define ANOMALY_05000426 (1)
+/* Software System Reset Corrupts PLL_LOCKCNT Register */
+#define ANOMALY_05000430 (1)
+/* Incorrect Use of Stack in Lockbox Firmware During Authentication */
+#define ANOMALY_05000431 (1)
+/* Certain SIC Registers are not Reset After Soft or Core Double Fault Reset */
+#define ANOMALY_05000435 (1)
+/* PORTx_DRIVE and PORTx_HYSTERESIS Registers Read Back Incorrect Values */
+#define ANOMALY_05000438 (1)
+/* Preboot Cannot be Used to Program the PLL_DIV Register */
+#define ANOMALY_05000439 (1)
+/* bfrom_SysControl() Cannot be Used to Write the PLL_DIV Register */
+#define ANOMALY_05000440 (1)
+/* IFLUSH Instruction at End of Hardware Loop Causes Infinite Stall */
+#define ANOMALY_05000443 (1)
+/* Incorrect L1 Instruction Bank B Memory Map Location */
+#define ANOMALY_05000444 (1)
+
+/* Anomalies that don't exist on this proc */
+#define ANOMALY_05000125 (0)
+#define ANOMALY_05000158 (0)
+#define ANOMALY_05000183 (0)
+#define ANOMALY_05000198 (0)
+#define ANOMALY_05000230 (0)
+#define ANOMALY_05000244 (0)
+#define ANOMALY_05000261 (0)
+#define ANOMALY_05000263 (0)
+#define ANOMALY_05000266 (0)
+#define ANOMALY_05000273 (0)
+#define ANOMALY_05000285 (0)
+#define ANOMALY_05000307 (0)
+#define ANOMALY_05000311 (0)
+#define ANOMALY_05000312 (0)
+#define ANOMALY_05000323 (0)
+#define ANOMALY_05000353 (0)
+#define ANOMALY_05000363 (0)
+#define ANOMALY_05000386 (0)
+
+#endif

arch/blackfin/mach-bf518/include/mach/bf518.h

+/*
+ * File:         include/asm-blackfin/mach-bf518/bf518.h
+ * Based on:	include/asm-blackfin/mach-bf527/bf527.h
+ * Author:	Michael Hennerich (michael.hennerich@analog.com)
+ *
+ * Created:
+ * Description:  SYSTEM MMR REGISTER AND MEMORY MAP FOR ADSP-BF518
+ *
+ * Modified:
+ *               Copyright 2004-2007 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#ifndef __MACH_BF518_H__
+#define __MACH_BF518_H__
+
+#define OFFSET_(x) ((x) & 0x0000FFFF)
+
+/*some misc defines*/
+#define IMASK_IVG15		0x8000
+#define IMASK_IVG14		0x4000
+#define IMASK_IVG13		0x2000
+#define IMASK_IVG12		0x1000
+
+#define IMASK_IVG11		0x0800
+#define IMASK_IVG10		0x0400
+#define IMASK_IVG9		0x0200
+#define IMASK_IVG8		0x0100
+
+#define IMASK_IVG7		0x0080
+#define IMASK_IVGTMR		0x0040
+#define IMASK_IVGHW		0x0020
+
+/***************************/
+
+#define BFIN_DSUBBANKS	4
+#define BFIN_DWAYS		2
+#define BFIN_DLINES		64
+#define BFIN_ISUBBANKS	4
+#define BFIN_IWAYS		4
+#define BFIN_ILINES		32
+
+#define WAY0_L			0x1
+#define WAY1_L			0x2
+#define WAY01_L			0x3
+#define WAY2_L			0x4
+#define WAY02_L			0x5
+#define	WAY12_L			0x6
+#define	WAY012_L		0x7
+
+#define	WAY3_L			0x8
+#define	WAY03_L			0x9
+#define	WAY13_L			0xA
+#define	WAY013_L		0xB
+
+#define	WAY32_L			0xC
+#define	WAY320_L		0xD
+#define	WAY321_L		0xE
+#define	WAYALL_L		0xF
+
+#define DMC_ENABLE (2<<2)	/*yes, 2, not 1 */
+
+/********************************* EBIU Settings ************************************/
+#define AMBCTL0VAL	((CONFIG_BANK_1 << 16) | CONFIG_BANK_0)
+#define AMBCTL1VAL	((CONFIG_BANK_3 << 16) | CONFIG_BANK_2)
+
+#ifdef CONFIG_C_AMBEN_ALL
+#define V_AMBEN AMBEN_ALL
+#endif
+#ifdef CONFIG_C_AMBEN
+#define V_AMBEN 0x0
+#endif
+#ifdef CONFIG_C_AMBEN_B0
+#define V_AMBEN AMBEN_B0
+#endif
+#ifdef CONFIG_C_AMBEN_B0_B1
+#define V_AMBEN AMBEN_B0_B1
+#endif
+#ifdef CONFIG_C_AMBEN_B0_B1_B2
+#define V_AMBEN AMBEN_B0_B1_B2
+#endif
+#ifdef CONFIG_C_AMCKEN
+#define V_AMCKEN AMCKEN
+#else
+#define V_AMCKEN 0x0
+#endif
+#ifdef CONFIG_C_CDPRIO
+#define V_CDPRIO 0x100
+#else
+#define V_CDPRIO 0x0
+#endif
+
+#define AMGCTLVAL	(V_AMBEN | V_AMCKEN | V_CDPRIO)
+
+#ifdef CONFIG_BF518
+#define CPU "BF518"
+#define CPUID 0x27e8
+#endif
+#ifdef CONFIG_BF516
+#define CPU "BF516"
+#define CPUID 0x27e8
+#endif
+#ifdef CONFIG_BF514
+#define CPU "BF514"
+#define CPUID 0x27e8
+#endif
+#ifdef CONFIG_BF512
+#define CPU "BF512"
+#define CPUID 0x27e8
+#endif
+
+#ifndef CPU
+#error "Unknown CPU type - This kernel doesn't seem to be configured properly"
+#endif
+
+#endif				/* __MACH_BF518_H__  */

arch/blackfin/mach-bf518/include/mach/bfin_serial_5xx.h

+/*
+ * file:        include/asm-blackfin/mach-bf518/bfin_serial_5xx.h
+ * based on:
+ * author:
+ *
+ * created:
+ * description:
+ *	blackfin serial driver head file
+ * rev:
+ *
+ * modified:
+ *
+ *
+ * bugs:         enter bugs at http://blackfin.uclinux.org/
+ *
+ * this program is free software; you can redistribute it and/or modify
+ * it under the terms of the gnu general public license as published by
+ * the free software foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * this program is distributed in the hope that it will be useful,
+ * but without any warranty; without even the implied warranty of
+ * merchantability or fitness for a particular purpose.  see the
+ * gnu general public license for more details.
+ *
+ * you should have received a copy of the gnu general public license
+ * along with this program; see the file copying.
+ * if not, write to the free software foundation,
+ * 59 temple place - suite 330, boston, ma 02111-1307, usa.
+ */
+
+#include <linux/serial.h>
+#include <asm/dma.h>
+#include <asm/portmux.h>
+
+#define UART_GET_CHAR(uart)     bfin_read16(((uart)->port.membase + OFFSET_RBR))
+#define UART_GET_DLL(uart)	bfin_read16(((uart)->port.membase + OFFSET_DLL))
+#define UART_GET_IER(uart)      bfin_read16(((uart)->port.membase + OFFSET_IER))
+#define UART_GET_DLH(uart)	bfin_read16(((uart)->port.membase + OFFSET_DLH))
+#define UART_GET_IIR(uart)      bfin_read16(((uart)->port.membase + OFFSET_IIR))
+#define UART_GET_LCR(uart)      bfin_read16(((uart)->port.membase + OFFSET_LCR))
+#define UART_GET_GCTL(uart)     bfin_read16(((uart)->port.membase + OFFSET_GCTL))
+
+#define UART_PUT_CHAR(uart, v)   bfin_write16(((uart)->port.membase + OFFSET_THR), v)
+#define UART_PUT_DLL(uart, v)    bfin_write16(((uart)->port.membase + OFFSET_DLL), v)
+#define UART_PUT_IER(uart, v)    bfin_write16(((uart)->port.membase + OFFSET_IER), v)
+#define UART_SET_IER(uart, v)    UART_PUT_IER(uart, UART_GET_IER(uart) | (v))
+#define UART_CLEAR_IER(uart, v)  UART_PUT_IER(uart, UART_GET_IER(uart) & ~(v))
+#define UART_PUT_DLH(uart, v)    bfin_write16(((uart)->port.membase + OFFSET_DLH), v)
+#define UART_PUT_LCR(uart, v)    bfin_write16(((uart)->port.membase + OFFSET_LCR), v)
+#define UART_PUT_GCTL(uart, v)   bfin_write16(((uart)->port.membase + OFFSET_GCTL), v)
+
+#define UART_SET_DLAB(uart)     do { UART_PUT_LCR(uart, UART_GET_LCR(uart) | DLAB); SSYNC(); } while (0)
+#define UART_CLEAR_DLAB(uart)   do { UART_PUT_LCR(uart, UART_GET_LCR(uart) & ~DLAB); SSYNC(); } while (0)
+
+#define UART_GET_CTS(x) gpio_get_value(x->cts_pin)
+#define UART_SET_RTS(x) gpio_set_value(x->rts_pin, 1)
+#define UART_CLEAR_RTS(x) gpio_set_value(x->rts_pin, 0)
+#define UART_ENABLE_INTS(x, v) UART_PUT_IER(x, v)
+#define UART_DISABLE_INTS(x) UART_PUT_IER(x, 0)
+
+#if defined(CONFIG_BFIN_UART0_CTSRTS) || defined(CONFIG_BFIN_UART1_CTSRTS)
+# define CONFIG_SERIAL_BFIN_CTSRTS
+
+# ifndef CONFIG_UART0_CTS_PIN
+#  define CONFIG_UART0_CTS_PIN -1
+# endif
+
+# ifndef CONFIG_UART0_RTS_PIN
+#  define CONFIG_UART0_RTS_PIN -1
+# endif
+
+# ifndef CONFIG_UART1_CTS_PIN
+#  define CONFIG_UART1_CTS_PIN -1
+# endif
+
+# ifndef CONFIG_UART1_RTS_PIN
+#  define CONFIG_UART1_RTS_PIN -1
+# endif
+#endif
+
+#define BFIN_UART_TX_FIFO_SIZE	2
+
+/*
+ * The pin configuration is different from schematic
+ */
+struct bfin_serial_port {
+	struct uart_port port;
+	unsigned int old_status;
+	unsigned int lsr;
+#ifdef CONFIG_SERIAL_BFIN_DMA
+	int tx_done;
+	int tx_count;
+	struct circ_buf rx_dma_buf;
+	struct timer_list rx_dma_timer;
+	int rx_dma_nrows;
+	unsigned int tx_dma_channel;
+	unsigned int rx_dma_channel;
+	struct work_struct tx_dma_workqueue;
+#endif
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+	struct timer_list cts_timer;
+	int cts_pin;
+	int rts_pin;
+#endif
+};
+
+/* The hardware clears the LSR bits upon read, so we need to cache
+ * some of the more fun bits in software so they don't get lost
+ * when checking the LSR in other code paths (TX).
+ */
+static inline unsigned int UART_GET_LSR(struct bfin_serial_port *uart)
+{
+	unsigned int lsr = bfin_read16(uart->port.membase + OFFSET_LSR);
+	uart->lsr |= (lsr & (BI|FE|PE|OE));
+	return lsr | uart->lsr;
+}
+
+static inline void UART_CLEAR_LSR(struct bfin_serial_port *uart)
+{
+	uart->lsr = 0;
+	bfin_write16(uart->port.membase + OFFSET_LSR, -1);
+}
+
+struct bfin_serial_res {
+	unsigned long uart_base_addr;
+	int uart_irq;
+#ifdef CONFIG_SERIAL_BFIN_DMA
+	unsigned int uart_tx_dma_channel;
+	unsigned int uart_rx_dma_channel;
+#endif
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+	int uart_cts_pin;
+	int uart_rts_pin;
+#endif
+};
+
+struct bfin_serial_res bfin_serial_resource[] = {
+#ifdef CONFIG_SERIAL_BFIN_UART0
+	{
+	 0xFFC00400,
+	 IRQ_UART0_RX,
+#ifdef CONFIG_SERIAL_BFIN_DMA
+	 CH_UART0_TX,
+	 CH_UART0_RX,
+#endif
+#ifdef CONFIG_BFIN_UART0_CTSRTS
+	 CONFIG_UART0_CTS_PIN,
+	 CONFIG_UART0_RTS_PIN,
+#endif
+	 },
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+	{
+	 0xFFC02000,
+	 IRQ_UART1_RX,
+#ifdef CONFIG_SERIAL_BFIN_DMA
+	 CH_UART1_TX,
+	 CH_UART1_RX,
+#endif
+#ifdef CONFIG_BFIN_UART1_CTSRTS
+	 CONFIG_UART1_CTS_PIN,
+	 CONFIG_UART1_RTS_PIN,
+#endif
+	 },
+#endif
+};
+
+#define DRIVER_NAME "bfin-uart"

arch/blackfin/mach-bf518/include/mach/bfin_sir.h

+/*
+ * Blackfin Infra-red Driver
+ *
+ * Copyright 2006-2008 Analog Devices Inc.
+ *
+ * Enter bugs at http://blackfin.uclinux.org/
+ *
+ * Licensed under the GPL-2 or later.
+ *
+ */
+
+#include <linux/serial.h>
+#include <asm/dma.h>
+#include <asm/portmux.h>
+
+#define SIR_UART_GET_CHAR(port)   bfin_read16((port)->membase + OFFSET_RBR)
+#define SIR_UART_GET_DLL(port)    bfin_read16((port)->membase + OFFSET_DLL)
+#define SIR_UART_GET_IER(port)    bfin_read16((port)->membase + OFFSET_IER)
+#define SIR_UART_GET_DLH(port)    bfin_read16((port)->membase + OFFSET_DLH)
+#define SIR_UART_GET_IIR(port)    bfin_read16((port)->membase + OFFSET_IIR)
+#define SIR_UART_GET_LCR(port)    bfin_read16((port)->membase + OFFSET_LCR)
+#define SIR_UART_GET_GCTL(port)   bfin_read16((port)->membase + OFFSET_GCTL)
+
+#define SIR_UART_PUT_CHAR(port, v) bfin_write16(((port)->membase + OFFSET_THR), v)
+#define SIR_UART_PUT_DLL(port, v)  bfin_write16(((port)->membase + OFFSET_DLL), v)
+#define SIR_UART_PUT_IER(port, v)  bfin_write16(((port)->membase + OFFSET_IER), v)
+#define SIR_UART_PUT_DLH(port, v)  bfin_write16(((port)->membase + OFFSET_DLH), v)
+#define SIR_UART_PUT_LCR(port, v)  bfin_write16(((port)->membase + OFFSET_LCR), v)
+#define SIR_UART_PUT_GCTL(port, v) bfin_write16(((port)->membase + OFFSET_GCTL), v)
+
+#ifdef CONFIG_SIR_BFIN_DMA
+struct dma_rx_buf {
+	char *buf;
+	int head;
+	int tail;
+	};
+#endif /* CONFIG_SIR_BFIN_DMA */
+
+struct bfin_sir_port {
+	unsigned char __iomem   *membase;
+	unsigned int            irq;
+	unsigned int            lsr;
+	unsigned long           clk;
+	struct net_device       *dev;
+#ifdef CONFIG_SIR_BFIN_DMA
+	int                     tx_done;
+	struct dma_rx_buf       rx_dma_buf;
+	struct timer_list       rx_dma_timer;
+	int                     rx_dma_nrows;
+#endif /* CONFIG_SIR_BFIN_DMA */
+	unsigned int            tx_dma_channel;
+	unsigned int            rx_dma_channel;
+};
+
+struct bfin_sir_port sir_ports[BFIN_UART_NR_PORTS];
+
+struct bfin_sir_port_res {
+	unsigned long   base_addr;
+	int             irq;
+	unsigned int    rx_dma_channel;
+	unsigned int    tx_dma_channel;
+};
+
+struct bfin_sir_port_res bfin_sir_port_resource[] = {
+#ifdef CONFIG_BFIN_SIR0
+	{
+	0xFFC00400,
+	IRQ_UART0_RX,
+	CH_UART0_RX,
+	CH_UART0_TX,
+	},
+#endif
+#ifdef CONFIG_BFIN_SIR1
+	{
+	0xFFC02000,
+	IRQ_UART1_RX,
+	CH_UART1_RX,
+	CH_UART1_TX,
+	},
+#endif
+};
+
+int nr_sirs = ARRAY_SIZE(bfin_sir_port_resource);
+
+struct bfin_sir_self {
+	struct bfin_sir_port    *sir_port;
+	spinlock_t              lock;
+	unsigned int            open;
+	int                     speed;
+	int                     newspeed;
+
+	struct sk_buff          *txskb;
+	struct sk_buff          *rxskb;
+	struct net_device_stats stats;
+	struct device           *dev;
+	struct irlap_cb         *irlap;
+	struct qos_info         qos;
+
+	iobuff_t                tx_buff;
+	iobuff_t                rx_buff;
+
+	struct work_struct      work;
+	int                     mtt;
+};
+
+static inline unsigned int SIR_UART_GET_LSR(struct bfin_sir_port *port)
+{
+	unsigned int lsr = bfin_read16(port->membase + OFFSET_LSR);
+	port->lsr |= (lsr & (BI|FE|PE|OE));
+	return lsr | port->lsr;
+}
+
+static inline void SIR_UART_CLEAR_LSR(struct bfin_sir_port *port)
+{
+	port->lsr = 0;
+	bfin_read16(port->membase + OFFSET_LSR);
+}
+
+#define DRIVER_NAME "bfin_sir"
+
+static int bfin_sir_hw_init(void)
+{
+	int ret = -ENODEV;
+#ifdef CONFIG_BFIN_SIR0
+	ret = peripheral_request(P_UART0_TX, DRIVER_NAME);
+	if (ret)
+		return ret;
+	ret = peripheral_request(P_UART0_RX, DRIVER_NAME);
+	if (ret)
+		return ret;
+#endif
+
+#ifdef CONFIG_BFIN_SIR1
+	ret = peripheral_request(P_UART1_TX, DRIVER_NAME);
+	if (ret)
+		return ret;
+	ret = peripheral_request(P_UART1_RX, DRIVER_NAME);
+	if (ret)
+		return ret;
+#endif
+	return ret;
+}

arch/blackfin/mach-bf518/include/mach/blackfin.h

+/*
+ * File:         include/asm-blackfin/mach-bf518/blackfin.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:
+ *
+ * Rev:
+ *
+ * Modified:
+ *
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#ifndef _MACH_BLACKFIN_H_
+#define _MACH_BLACKFIN_H_
+
+#define BF518_FAMILY
+
+#include "bf518.h"
+#include "mem_map.h"
+#include "defBF512.h"
+#include "anomaly.h"
+
+#if defined(CONFIG_BF518)
+#include "defBF518.h"
+#endif
+
+#if defined(CONFIG_BF516)
+#include "defBF516.h"
+#endif
+
+#if defined(CONFIG_BF514)
+#include "defBF514.h"
+#endif
+
+#if defined(CONFIG_BF512)
+#include "defBF512.h"
+#endif
+
+#if !defined(__ASSEMBLY__)
+#include "cdefBF512.h"
+
+#if defined(CONFIG_BF518)
+#include "cdefBF518.h"
+#endif
+
+#if defined(CONFIG_BF516)
+#include "cdefBF516.h"
+#endif
+
+#if defined(CONFIG_BF514)
+#include "cdefBF514.h"
+#endif
+#endif
+
+/* UART_IIR Register */
+#define STATUS(x)	((x << 1) & 0x06)
+#define STATUS_P1	0x02
+#define STATUS_P0	0x01
+
+#define BFIN_UART_NR_PORTS	2
+
+#define OFFSET_THR              0x00	/* Transmit Holding register            */
+#define OFFSET_RBR              0x00	/* Receive Buffer register              */
+#define OFFSET_DLL              0x00	/* Divisor Latch (Low-Byte)             */
+#define OFFSET_IER              0x04	/* Interrupt Enable Register            */
+#define OFFSET_DLH              0x04	/* Divisor Latch (High-Byte)            */
+#define OFFSET_IIR              0x08	/* Interrupt Identification Register    */
+#define OFFSET_LCR              0x0C	/* Line Control Register                */
+#define OFFSET_MCR              0x10	/* Modem Control Register               */
+#define OFFSET_LSR              0x14	/* Line Status Register                 */
+#define OFFSET_MSR              0x18	/* Modem Status Register                */
+#define OFFSET_SCR              0x1C	/* SCR Scratch Register                 */
+#define OFFSET_GCTL             0x24	/* Global Control Register              */
+
+/* DPMC*/
+#define bfin_read_STOPCK_OFF() bfin_read_STOPCK()
+#define bfin_write_STOPCK_OFF(val) bfin_write_STOPCK(val)
+#define STOPCK_OFF STOPCK
+
+/* PLL_DIV Masks													*/
+#define CCLK_DIV1 CSEL_DIV1	/*          CCLK = VCO / 1                                  */
+#define CCLK_DIV2 CSEL_DIV2	/*          CCLK = VCO / 2                                  */
+#define CCLK_DIV4 CSEL_DIV4	/*          CCLK = VCO / 4                                  */
+#define CCLK_DIV8 CSEL_DIV8	/*          CCLK = VCO / 8                                  */
+
+#endif

arch/blackfin/mach-bf518/include/mach/cdefBF512.h

+/*
+ * File:         include/asm-blackfin/mach-bf518/cdefbf512.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:  system mmr register map
+ *
+ * Rev:
+ *
+ * Modified:
+ *
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#ifndef _CDEF_BF512_H
+#define _CDEF_BF512_H
+
+/* include all Core registers and bit definitions */
+#include "defBF512.h"
+
+/* include core specific register pointer definitions */
+#include <asm/cdef_LPBlackfin.h>
+
+/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF512 */
+
+/* include cdefBF51x_base.h for the set of #defines that are common to all ADSP-BF51x processors */
+#include "cdefBF51x_base.h"
+
+#endif /* _CDEF_BF512_H */

arch/blackfin/mach-bf518/include/mach/cdefBF514.h

+/*
+ * File:         include/asm-blackfin/mach-bf518/cdefbf514.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:  system mmr register map
+ *
+ * Rev:
+ *
+ * Modified:
+ *
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#ifndef _CDEF_BF514_H
+#define _CDEF_BF514_H
+
+/* include all Core registers and bit definitions */
+#include "defBF514.h"
+
+/* include core specific register pointer definitions */
+#include <asm/cdef_LPBlackfin.h>
+
+/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF514 */
+
+/* include cdefBF51x_base.h for the set of #defines that are common to all ADSP-BF51x processors */
+#include "cdefBF51x_base.h"
+
+/* The following are the #defines needed by ADSP-BF514 that are not in the common header */
+
+#endif /* _CDEF_BF514_H */

arch/blackfin/mach-bf518/include/mach/cdefBF516.h

+/*
+ * File:         include/asm-blackfin/mach-bf518/cdefbf516.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:  system mmr register map
+ *
+ * Rev:
+ *
+ * Modified:
+ *
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#ifndef _CDEF_BF516_H
+#define _CDEF_BF516_H
+
+/* include all Core registers and bit definitions */
+#include "defBF516.h"
+
+/* include core specific register pointer definitions */
+#include <asm/cdef_LPBlackfin.h>
+
+/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF516 */
+
+/* include cdefBF51x_base.h for the set of #defines that are common to all ADSP-BF51x processors */
+#include "cdefBF51x_base.h"
+
+/* The following are the #defines needed by ADSP-BF516 that are not in the common header */
+
+#endif /* _CDEF_BF516_H */

arch/blackfin/mach-bf518/include/mach/cdefBF518.h

+/*
+ * File:         include/asm-blackfin/mach-bf518/cdefbf518.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:  system mmr register map
+ *
+ * Rev:
+ *
+ * Modified:
+ *
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#ifndef _CDEF_BF518_H
+#define _CDEF_BF518_H
+
+/* include all Core registers and bit definitions */
+#include "defBF518.h"
+
+/* include core specific register pointer definitions */
+#include <asm/cdef_LPBlackfin.h>
+
+/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF518 */
+
+/* include cdefBF51x_base.h for the set of #defines that are common to all ADSP-BF51x processors */
+#include "cdefBF51x_base.h"
+
+/* The following are the #defines needed by ADSP-BF518 that are not in the common header */
+
+#endif /* _CDEF_BF518_H */

arch/blackfin/mach-bf518/include/mach/defBF512.h

+/*
+ * File:         include/asm-blackfin/mach-bf518/defBF512.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:
+ *
+ * Rev:
+ *
+ * Modified:
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#ifndef _DEF_BF512_H
+#define _DEF_BF512_H
+
+/* Include all Core registers and bit definitions */
+#include <asm/def_LPBlackfin.h>
+
+/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF512 */
+
+/* Include defBF51x_base.h for the set of #defines that are common to all ADSP-BF51x processors */
+#include "defBF51x_base.h"
+
+#endif /* _DEF_BF512_H */

arch/blackfin/mach-bf518/include/mach/defBF514.h

+/*
+ * File:         include/asm-blackfin/mach-bf518/defBF514.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:
+ *
+ * Rev:
+ *
+ * Modified:
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#ifndef _DEF_BF514_H
+#define _DEF_BF514_H
+
+/* Include all Core registers and bit definitions */
+#include <asm/def_LPBlackfin.h>
+
+/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF514 */
+
+/* Include defBF51x_base.h for the set of #defines that are common to all ADSP-BF51x processors */
+#include "defBF51x_base.h"
+
+/* The following are the #defines needed by ADSP-BF514 that are not in the common header */
+
+/* SDH Registers */
+
+#define SDH_PWR_CTL                    0xFFC03900 /* SDH Power Control */
+#define SDH_CLK_CTL                    0xFFC03904 /* SDH Clock Control */
+#define SDH_ARGUMENT                   0xFFC03908 /* SDH Argument */
+#define SDH_COMMAND                    0xFFC0390C /* SDH Command */
+#define SDH_RESP_CMD                   0xFFC03910 /* SDH Response Command */
+#define SDH_RESPONSE0                  0xFFC03914 /* SDH Response0 */
+#define SDH_RESPONSE1                  0xFFC03918 /* SDH Response1 */
+#define SDH_RESPONSE2                  0xFFC0391C /* SDH Response2 */
+#define SDH_RESPONSE3                  0xFFC03920 /* SDH Response3 */
+#define SDH_DATA_TIMER                 0xFFC03924 /* SDH Data Timer */
+#define SDH_DATA_LGTH                  0xFFC03928 /* SDH Data Length */
+#define SDH_DATA_CTL                   0xFFC0392C /* SDH Data Control */
+#define SDH_DATA_CNT                   0xFFC03930 /* SDH Data Counter */
+#define SDH_STATUS                     0xFFC03934 /* SDH Status */
+#define SDH_STATUS_CLR                 0xFFC03938 /* SDH Status Clear */
+#define SDH_MASK0                      0xFFC0393C /* SDH Interrupt0 Mask */
+#define SDH_MASK1                      0xFFC03940 /* SDH Interrupt1 Mask */
+#define SDH_FIFO_CNT                   0xFFC03948 /* SDH FIFO Counter */
+#define SDH_FIFO                       0xFFC03980 /* SDH Data FIFO */
+#define SDH_E_STATUS                   0xFFC039C0 /* SDH Exception Status */
+#define SDH_E_MASK                     0xFFC039C4 /* SDH Exception Mask */
+#define SDH_CFG                        0xFFC039C8 /* SDH Configuration */
+#define SDH_RD_WAIT_EN                 0xFFC039CC /* SDH Read Wait Enable */
+#define SDH_PID0                       0xFFC039D0 /* SDH Peripheral Identification0 */
+#define SDH_PID1                       0xFFC039D4 /* SDH Peripheral Identification1 */
+#define SDH_PID2                       0xFFC039D8 /* SDH Peripheral Identification2 */
+#define SDH_PID3                       0xFFC039DC /* SDH Peripheral Identification3 */
+#define SDH_PID4                       0xFFC039E0 /* SDH Peripheral Identification4 */
+#define SDH_PID5                       0xFFC039E4 /* SDH Peripheral Identification5 */
+#define SDH_PID6                       0xFFC039E8 /* SDH Peripheral Identification6 */
+#define SDH_PID7                       0xFFC039EC /* SDH Peripheral Identification7 */
+
+/* Removable Storage Interface Registers */
+
+#define RSI_PWR_CONTROL                0xFFC03800 /* RSI Power Control Register */
+#define RSI_CLK_CONTROL                0xFFC03804 /* RSI Clock Control Register */
+#define RSI_ARGUMENT                   0xFFC03808 /* RSI Argument Register */
+#define RSI_COMMAND                    0xFFC0380C /* RSI Command Register */
+#define RSI_RESP_CMD                   0xFFC03810 /* RSI Response Command Register */
+#define RSI_RESPONSE0                  0xFFC03814 /* RSI Response Register */
+#define RSI_RESPONSE1                  0xFFC03818 /* RSI Response Register */
+#define RSI_RESPONSE2                  0xFFC0381C /* RSI Response Register */
+#define RSI_RESPONSE3                  0xFFC03820 /* RSI Response Register */
+#define RSI_DATA_TIMER                 0xFFC03824 /* RSI Data Timer Register */
+#define RSI_DATA_LGTH                  0xFFC03828 /* RSI Data Length Register */
+#define RSI_DATA_CONTROL               0xFFC0382C /* RSI Data Control Register */
+#define RSI_DATA_CNT                   0xFFC03830 /* RSI Data Counter Register */
+#define RSI_STATUS                     0xFFC03834 /* RSI Status Register */
+#define RSI_STATUSCL                   0xFFC03838 /* RSI Status Clear Register */
+#define RSI_MASK0                      0xFFC0383C /* RSI Interrupt 0 Mask Register */
+#define RSI_MASK1                      0xFFC03840 /* RSI Interrupt 1 Mask Register */
+#define RSI_FIFO_CNT                   0xFFC03848 /* RSI FIFO Counter Register */
+#define RSI_CEATA_CONTROL              0xFFC0384C /* RSI CEATA Register */
+#define RSI_FIFO                       0xFFC03880 /* RSI Data FIFO Register */
+#define RSI_ESTAT                      0xFFC038C0 /* RSI Exception Status Register */
+#define RSI_EMASK                      0xFFC038C4 /* RSI Exception Mask Register */
+#define RSI_CONFIG                     0xFFC038C8 /* RSI Configuration Register */
+#define RSI_RD_WAIT_EN                 0xFFC038CC /* RSI Read Wait Enable Register */
+#define RSI_PID0                       0xFFC03FE0 /* RSI Peripheral ID Register 0 */
+#define RSI_PID1                       0xFFC03FE4 /* RSI Peripheral ID Register 1 */
+#define RSI_PID2                       0xFFC03FE8 /* RSI Peripheral ID Register 2 */
+#define RSI_PID3                       0xFFC03FEC /* RSI Peripheral ID Register 3 */
+#define RSI_PID4                       0xFFC03FF0 /* RSI Peripheral ID Register 4 */
+#define RSI_PID5                       0xFFC03FF4 /* RSI Peripheral ID Register 5 */
+#define RSI_PID6                       0xFFC03FF8 /* RSI Peripheral ID Register 6 */
+#define RSI_PID7                       0xFFC03FFC /* RSI Peripheral ID Register 7 */
+
+#endif /* _DEF_BF514_H */

arch/blackfin/mach-bf518/include/mach/dma.h

+/*
+ * file:        include/asm-blackfin/mach-bf518/dma.h
+ * based on:	include/asm-blackfin/mach-bf527/dma.h
+ * author:	Michael Hennerich (michael.hennerich@analog.com)
+ *
+ * created:
+ * description:
+ *	system DMA map
+ * rev:
+ *
+ * modified:
+ *
+ *
+ * bugs:         enter bugs at http://blackfin.uclinux.org/
+ *
+ * this program is free software; you can redistribute it and/or modify
+ * it under the terms of the gnu general public license as published by
+ * the free software foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * this program is distributed in the hope that it will be useful,
+ * but without any warranty; without even the implied warranty of
+ * merchantability or fitness for a particular purpose.  see the
+ * gnu general public license for more details.
+ *
+ * you should have received a copy of the gnu general public license
+ * along with this program; see the file copying.
+ * if not, write to the free software foundation,
+ * 59 temple place - suite 330, boston, ma 02111-1307, usa.
+ */
+
+#ifndef _MACH_DMA_H_
+#define _MACH_DMA_H_
+
+#define MAX_BLACKFIN_DMA_CHANNEL 16
+
+#define CH_PPI 			0	/* PPI receive/transmit */
+#define CH_EMAC_RX 		1	/* Ethernet MAC receive */
+#define CH_EMAC_TX 		2	/* Ethernet MAC transmit */
+#define CH_SPORT0_RX 		3	/* SPORT0 receive */
+#define CH_SPORT0_TX 		4	/* SPORT0 transmit */
+#define CH_RSI 			4	/* RSI */
+#define CH_SPORT1_RX 		5	/* SPORT1 receive */
+#define CH_SPI1 		5	/* SPI1 transmit/receive */
+#define CH_SPORT1_TX 		6	/* SPORT1 transmit */
+#define CH_SPI0 		7	/* SPI0 transmit/receive */
+#define CH_UART0_RX 		8	/* UART0 receive */
+#define CH_UART0_TX 		9	/* UART0 transmit */
+#define CH_UART1_RX 		10	/* UART1 receive */
+#define CH_UART1_TX 		11	/* UART1 transmit */
+
+#define CH_MEM_STREAM0_SRC 	12	/* RX */
+#define CH_MEM_STREAM0_DEST	13	/* TX */
+#define CH_MEM_STREAM1_SRC 	14	/* RX */
+#define CH_MEM_STREAM1_DEST	15	/* TX */
+
+#endif

arch/blackfin/mach-bf518/include/mach/mem_map.h

+/*
+ * file:         include/asm-blackfin/mach-bf518/mem_map.h
+ * based on:	include/asm-blackfin/mach-bf527/mem_map.h
+ * author:	Bryan Wu <cooloney@kernel.org>
+ *
+ * created:
+ * description:
+ *	Memory MAP Common header file for blackfin BF518/6/4/2 of processors.
+ * rev:
+ *
+ * modified:
+ *
+ * bugs:         enter bugs at http://blackfin.uclinux.org/
+ *
+ * this program is free software; you can redistribute it and/or modify
+ * it under the terms of the gnu general public license as published by
+ * the free software foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * this program is distributed in the hope that it will be useful,
+ * but without any warranty; without even the implied warranty of
+ * merchantability or fitness for a particular purpose.  see the
+ * gnu general public license for more details.
+ *
+ * you should have received a copy of the gnu general public license
+ * along with this program; see the file copying.
+ * if not, write to the free software foundation,
+ * 59 temple place - suite 330, boston, ma 02111-1307, usa.
+ */
+
+#ifndef _MEM_MAP_518_H_
+#define _MEM_MAP_518_H_
+
+#define COREMMR_BASE           0xFFE00000	/* Core MMRs */
+#define SYSMMR_BASE            0xFFC00000	/* System MMRs */
+
+/* Async Memory Banks */
+#define ASYNC_BANK3_BASE	0x20300000	/* Async Bank 3 */
+#define ASYNC_BANK3_SIZE	0x00100000	/* 1M */
+#define ASYNC_BANK2_BASE	0x20200000	/* Async Bank 2 */
+#define ASYNC_BANK2_SIZE	0x00100000	/* 1M */
+#define ASYNC_BANK1_BASE	0x20100000	/* Async Bank 1 */
+#define ASYNC_BANK1_SIZE	0x00100000	/* 1M */
+#define ASYNC_BANK0_BASE	0x20000000	/* Async Bank 0 */
+#define ASYNC_BANK0_SIZE	0x00100000	/* 1M */
+
+/* Boot ROM Memory */
+
+#define BOOT_ROM_START		0xEF000000
+#define BOOT_ROM_LENGTH		0x8000
+
+/* Level 1 Memory */
+
+/* Memory Map for ADSP-BF518/6/4/2 processors */
+
+#ifdef CONFIG_BFIN_ICACHE
+#define BFIN_ICACHESIZE		(16 * 1024)
+#else
+#define BFIN_ICACHESIZE		(0)
+#endif
+
+#define L1_CODE_START		0xFFA00000
+#define L1_DATA_A_START		0xFF800000
+#define L1_DATA_B_START		0xFF900000
+
+#define L1_CODE_LENGTH		0xC000
+
+#ifdef CONFIG_BFIN_DCACHE
+
+#ifdef CONFIG_BFIN_DCACHE_BANKA
+#define DMEM_CNTR (ACACHE_BSRAM | ENDCPLB | PORT_PREF0)
+#define L1_DATA_A_LENGTH	(0x8000 - 0x4000)
+#define L1_DATA_B_LENGTH	0x8000
+#define BFIN_DCACHESIZE		(16 * 1024)
+#define BFIN_DSUPBANKS		1
+#else
+#define DMEM_CNTR (ACACHE_BCACHE | ENDCPLB | PORT_PREF0)
+#define L1_DATA_A_LENGTH	(0x8000 - 0x4000)
+#define L1_DATA_B_LENGTH	(0x8000 - 0x4000)
+#define BFIN_DCACHESIZE		(32 * 1024)
+#define BFIN_DSUPBANKS		2
+#endif
+
+#else
+#define DMEM_CNTR (ASRAM_BSRAM | ENDCPLB | PORT_PREF0)
+#define L1_DATA_A_LENGTH	0x8000
+#define L1_DATA_B_LENGTH	0x8000
+#define BFIN_DCACHESIZE		0
+#define BFIN_DSUPBANKS		0
+#endif				/*CONFIG_BFIN_DCACHE */
+
+/* Level 2 Memory - none */
+
+#define L2_START	0
+#define L2_LENGTH	0
+
+/* Scratch Pad Memory */
+
+#define L1_SCRATCH_START	0xFFB00000
+#define L1_SCRATCH_LENGTH	0x1000
+
+#endif				/* _MEM_MAP_518_H_ */

arch/blackfin/mach-bf518/ints-priority.c

+/*
+ * File:         arch/blackfin/mach-bf518/ints-priority.c
+ * Based on:     arch/blackfin/mach-bf527/ints-priority.c
+ * Author:       Bryan Wu <cooloney@kernel.org>
+ *
+ * Created:
+ * Description:  Set up the interrupt priorities
+ *
+ * Modified:
+ *               Copyright 2004-2007 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/module.h>
+#include <linux/irq.h>
+#include <asm/blackfin.h>
+
+void __init program_IAR(void)
+{
+	/* Program the IAR0 Register with the configured priority */
+	bfin_write_SIC_IAR0(((CONFIG_IRQ_PLL_WAKEUP - 7) << IRQ_PLL_WAKEUP_POS) |
+			((CONFIG_IRQ_DMA0_ERROR - 7) << IRQ_DMA0_ERROR_POS) |
+			((CONFIG_IRQ_DMAR0_BLK - 7) << IRQ_DMAR0_BLK_POS) |
+			((CONFIG_IRQ_DMAR1_BLK - 7) << IRQ_DMAR1_BLK_POS) |
+			((CONFIG_IRQ_DMAR0_OVR - 7) << IRQ_DMAR0_OVR_POS) |
+			((CONFIG_IRQ_DMAR1_OVR - 7) << IRQ_DMAR1_OVR_POS) |
+			((CONFIG_IRQ_PPI_ERROR - 7) << IRQ_PPI_ERROR_POS) |
+			((CONFIG_IRQ_MAC_ERROR - 7) << IRQ_MAC_ERROR_POS));
+
+
+	bfin_write_SIC_IAR1(((CONFIG_IRQ_SPORT0_ERROR - 7) << IRQ_SPORT0_ERROR_POS) |
+			((CONFIG_IRQ_SPORT1_ERROR - 7) << IRQ_SPORT1_ERROR_POS) |
+			((CONFIG_IRQ_PTP_ERROR - 7) << IRQ_PTP_ERROR_POS) |
+			((CONFIG_IRQ_UART0_ERROR - 7) << IRQ_UART0_ERROR_POS) |
+			((CONFIG_IRQ_UART1_ERROR - 7) << IRQ_UART1_ERROR_POS) |
+			((CONFIG_IRQ_RTC - 7) << IRQ_RTC_POS) |
+			((CONFIG_IRQ_PPI - 7) << IRQ_PPI_POS));
+
+	bfin_write_SIC_IAR2(((CONFIG_IRQ_SPORT0_RX - 7) << IRQ_SPORT0_RX_POS) |
+			((CONFIG_IRQ_SPORT0_TX - 7) << IRQ_SPORT0_TX_POS) |
+			((CONFIG_IRQ_SPORT1_RX - 7) << IRQ_SPORT1_RX_POS) |
+			((CONFIG_IRQ_SPORT1_TX - 7) << IRQ_SPORT1_TX_POS) |
+			((CONFIG_IRQ_TWI - 7) << IRQ_TWI_POS) |
+			((CONFIG_IRQ_SPI0 - 7) << IRQ_SPI0_POS) |
+			((CONFIG_IRQ_UART0_RX - 7) << IRQ_UART0_RX_POS) |
+			((CONFIG_IRQ_UART0_TX - 7) << IRQ_UART0_TX_POS));
+
+	bfin_write_SIC_IAR3(((CONFIG_IRQ_UART1_RX - 7) << IRQ_UART1_RX_POS) |
+			((CONFIG_IRQ_UART1_TX - 7) << IRQ_UART1_TX_POS) |
+			((CONFIG_IRQ_OPTSEC - 7) << IRQ_OPTSEC_POS) |
+			((CONFIG_IRQ_CNT - 7) << IRQ_CNT_POS) |
+			((CONFIG_IRQ_MAC_RX - 7) << IRQ_MAC_RX_POS) |
+			((CONFIG_IRQ_PORTH_INTA - 7) << IRQ_PORTH_INTA_POS) |
+			((CONFIG_IRQ_MAC_TX - 7) << IRQ_MAC_TX_POS) |
+			((CONFIG_IRQ_PORTH_INTB - 7) << IRQ_PORTH_INTB_POS));
+
+	bfin_write_SIC_IAR4(((CONFIG_IRQ_TMR0 - 7) << IRQ_TMR0_POS) |
+			((CONFIG_IRQ_TMR1 - 7) << IRQ_TMR1_POS) |
+			((CONFIG_IRQ_TMR2 - 7) << IRQ_TMR2_POS) |
+			((CONFIG_IRQ_TMR3 - 7) << IRQ_TMR3_POS) |
+			((CONFIG_IRQ_TMR4 - 7) << IRQ_TMR4_POS) |
+			((CONFIG_IRQ_TMR5 - 7) << IRQ_TMR5_POS) |
+			((CONFIG_IRQ_TMR6 - 7) << IRQ_TMR6_POS) |
+			((CONFIG_IRQ_TMR7 - 7) << IRQ_TMR7_POS));
+
+	bfin_write_SIC_IAR5(((CONFIG_IRQ_PORTG_INTA - 7) << IRQ_PORTG_INTA_POS) |
+			((CONFIG_IRQ_PORTG_INTB - 7) << IRQ_PORTG_INTB_POS) |
+			((CONFIG_IRQ_MEM_DMA0 - 7) << IRQ_MEM_DMA0_POS) |
+			((CONFIG_IRQ_MEM_DMA1 - 7) << IRQ_MEM_DMA1_POS) |
+			((CONFIG_IRQ_WATCH - 7) << IRQ_WATCH_POS) |
+			((CONFIG_IRQ_PORTF_INTA - 7) << IRQ_PORTF_INTA_POS) |
+			((CONFIG_IRQ_PORTF_INTB - 7) << IRQ_PORTF_INTB_POS) |
+			((CONFIG_IRQ_SPI0_ERROR - 7) << IRQ_SPI0_ERROR_POS));
+
+	bfin_write_SIC_IAR6(((CONFIG_IRQ_SPI1_ERROR - 7) << IRQ_SPI1_ERROR_POS) |
+			((CONFIG_IRQ_RSI_INT0 - 7) << IRQ_RSI_INT0_POS) |
+			((CONFIG_IRQ_RSI_INT1 - 7) << IRQ_RSI_INT1_POS) |
+			((CONFIG_IRQ_PWM_TRIP - 7) << IRQ_PWM_TRIP_POS) |
+			((CONFIG_IRQ_PWM_SYNC - 7) << IRQ_PWM_SYNC_POS) |
+			((CONFIG_IRQ_PTP_STAT - 7) << IRQ_PTP_STAT_POS));
+
+	SSYNC();
+}

arch/blackfin/mach-common/dpmc_modes.S

@@ -248,7 +248,7 @@ ENDPROC(_unset_dram_srfs)
 
 ENTRY(_set_sic_iwr)
 #if defined(CONFIG_BF54x) || defined(CONFIG_BF52x) || defined(CONFIG_BF561) || \
-	defined(CONFIG_BF538) || defined(CONFIG_BF539)
+	defined(CONFIG_BF538) || defined(CONFIG_BF539) || defined(CONFIG_BF51x)
 	P0.H = hi(SIC_IWR0);
 	P0.L = lo(SIC_IWR0);
 	P1.H = hi(SIC_IWR1);

arch/blackfin/mach-common/pm.c

@@ -83,9 +83,9 @@ void bfin_pm_suspend_standby_enter(void)
 	bfin_pm_standby_restore();
 
 #if defined(CONFIG_BF54x) || defined(CONFIG_BF52x)  || defined(CONFIG_BF561) || \
-	defined(CONFIG_BF538) || defined(CONFIG_BF539)
+	defined(CONFIG_BF538) || defined(CONFIG_BF539) || defined(CONFIG_BF51x)
 	bfin_write_SIC_IWR0(IWR_DISABLE_ALL);
-#if defined(CONFIG_BF52x)
+#if defined(CONFIG_BF52x) || defined(CONFIG_BF51x)
 	/* BF52x system reset does not properly reset SIC_IWR1 which
 	 * will screw up the bootrom as it relies on MDMA0/1 waking it
 	 * up from IDLE instructions.  See this report for more info: