ARM: imx: merge plat-mxc into mach-imx

It's really unnecessary to have plat-mxc, and let's merge it into
mach-imx.  It's pretty much just a bunch of file renaming and
Kconfig/Makefile merge.

To make the change less invasive, we keep using Kconfig symbol
CONFIG_ARCH_MXC for mach-imx sub-architecture.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>

MAINTAINERS

@@ -789,7 +789,6 @@ L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 T:	git git://git.pengutronix.de/git/imx/linux-2.6.git
 F:	arch/arm/mach-imx/
-F:	arch/arm/plat-mxc/
 F:	arch/arm/configs/imx*_defconfig
 
 ARM/FREESCALE IMX6

arch/arm/Kconfig

@@ -1058,7 +1058,7 @@ source "arch/arm/mach-msm/Kconfig"
 
 source "arch/arm/mach-mv78xx0/Kconfig"
 
-source "arch/arm/plat-mxc/Kconfig"
+source "arch/arm/mach-imx/Kconfig"
 
 source "arch/arm/mach-mxs/Kconfig"
 

arch/arm/Makefile

@@ -195,7 +195,6 @@ machine-$(CONFIG_ARCH_ZYNQ)		+= zynq
 
 # Platform directory name.  This list is sorted alphanumerically
 # by CONFIG_* macro name.
-plat-$(CONFIG_ARCH_MXC)		+= mxc
 plat-$(CONFIG_ARCH_OMAP)	+= omap
 plat-$(CONFIG_ARCH_S3C64XX)	+= samsung
 plat-$(CONFIG_ARCH_ZYNQ)	+= versatile

arch/arm/mach-imx/Kconfig

+if ARCH_MXC
+
+config MXC_IRQ_PRIOR
+	bool "Use IRQ priority"
+	help
+	  Select this if you want to use prioritized IRQ handling.
+	  This feature prevents higher priority ISR to be interrupted
+	  by lower priority IRQ even IRQF_DISABLED flag is not set.
+	  This may be useful in embedded applications, where are strong
+	  requirements for timing.
+	  Say N here, unless you have a specialized requirement.
+
+config MXC_TZIC
+	bool
+
+config MXC_AVIC
+	bool
+
+config MXC_DEBUG_BOARD
+	bool "Enable MXC debug board(for 3-stack)"
+	help
+	  The debug board is an integral part of the MXC 3-stack(PDK)
+	  platforms, it can be attached or removed from the peripheral
+	  board. On debug board, several debug devices(ethernet, UART,
+	  buttons, LEDs and JTAG) are implemented. Between the MCU and
+	  these devices, a CPLD is added as a bridge which performs
+	  data/address de-multiplexing and decode, signal level shift,
+	  interrupt control and various board functions.
+
+config HAVE_EPIT
+	bool
+
+config MXC_USE_EPIT
+	bool "Use EPIT instead of GPT"
+	depends on HAVE_EPIT
+	help
+	  Use EPIT as the system timer on systems that have it. Normally you
+	  don't have a reason to do so as the EPIT has the same features and
+	  uses the same clocks as the GPT. Anyway, on some systems the GPT
+	  may be in use for other purposes.
+
+config MXC_ULPI
+	bool
+
+config ARCH_HAS_RNGA
+	bool
+
+config IRAM_ALLOC
+	bool
+	select GENERIC_ALLOCATOR
+
 config HAVE_IMX_GPC
 	bool
 
@@ -110,6 +161,20 @@ config	SOC_IMX51
 	select PINCTRL_IMX51
 	select SOC_IMX5
 
+menu "Freescale MXC Implementations"
+
+choice
+	prompt "Freescale CPU family:"
+	default ARCH_IMX_V6_V7
+
+config ARCH_IMX_V4_V5
+	bool "i.MX1, i.MX21, i.MX25, i.MX27"
+	select ARM_PATCH_PHYS_VIRT
+	select AUTO_ZRELADDR if !ZBOOT_ROM
+	help
+	  This enables support for systems based on the Freescale i.MX ARMv4
+	  and ARMv5 SoCs
+
 if ARCH_IMX_V4_V5
 
 comment "MX1 platforms:"
@@ -390,6 +455,15 @@ config MACH_IMX27_DT
 
 endif
 
+config ARCH_IMX_V6_V7
+	bool "i.MX3, i.MX5, i.MX6"
+	select ARM_PATCH_PHYS_VIRT
+	select AUTO_ZRELADDR if !ZBOOT_ROM
+	select MIGHT_HAVE_CACHE_L2X0
+	help
+	  This enables support for systems based on the Freescale i.MX3, i.MX5
+	  and i.MX6 family.
+
 if ARCH_IMX_V6_V7
 
 comment "MX31 platforms:"
@@ -773,4 +847,10 @@ config SOC_IMX6Q
 
 endif
 
+endchoice
+
+endmenu
+
 source "arch/arm/mach-imx/devices/Kconfig"
+
+endif

arch/arm/mach-imx/Makefile

+obj-y := time.o cpu.o system.o irq-common.o
+
 obj-$(CONFIG_SOC_IMX1) += clk-imx1.o mm-imx1.o
 obj-$(CONFIG_SOC_IMX21) += clk-imx21.o mm-imx21.o
 
@@ -18,6 +20,21 @@ obj-$(CONFIG_COMMON_CLK) += clk-pllv1.o clk-pllv2.o clk-pllv3.o clk-gate2.o \
 obj-$(CONFIG_IMX_HAVE_IOMUX_V1) += iomux-v1.o
 obj-$(CONFIG_ARCH_MXC_IOMUX_V3) += iomux-v3.o
 
+obj-$(CONFIG_MXC_TZIC) += tzic.o
+obj-$(CONFIG_MXC_AVIC) += avic.o
+
+obj-$(CONFIG_IRAM_ALLOC) += iram_alloc.o
+obj-$(CONFIG_MXC_ULPI) += ulpi.o
+obj-$(CONFIG_MXC_USE_EPIT) += epit.o
+obj-$(CONFIG_MXC_DEBUG_BOARD) += 3ds_debugboard.o
+obj-$(CONFIG_CPU_FREQ_IMX)    += cpufreq.o
+obj-$(CONFIG_CPU_IDLE) += cpuidle.o
+
+ifdef CONFIG_SND_IMX_SOC
+obj-y += ssi-fiq.o
+obj-y += ssi-fiq-ksym.o
+endif
+
 # Support for CMOS sensor interface
 obj-$(CONFIG_MX1_VIDEO) += mx1-camera-fiq.o mx1-camera-fiq-ksym.o
 

arch/arm/plat-mxc/Kconfig

-if ARCH_MXC
-
-menu "Freescale MXC Implementations"
-
-choice
-	prompt "Freescale CPU family:"
-	default ARCH_IMX_V6_V7
-
-config ARCH_IMX_V4_V5
-	bool "i.MX1, i.MX21, i.MX25, i.MX27"
-	select ARM_PATCH_PHYS_VIRT
-	select AUTO_ZRELADDR if !ZBOOT_ROM
-	help
-	  This enables support for systems based on the Freescale i.MX ARMv4
-	  and ARMv5 SoCs
-
-config ARCH_IMX_V6_V7
-	bool "i.MX3, i.MX5, i.MX6"
-	select ARM_PATCH_PHYS_VIRT
-	select AUTO_ZRELADDR if !ZBOOT_ROM
-	select MIGHT_HAVE_CACHE_L2X0
-	help
-	  This enables support for systems based on the Freescale i.MX3, i.MX5
-	  and i.MX6 family.
-
-endchoice
-
-source "arch/arm/mach-imx/Kconfig"
-
-endmenu
-
-config MXC_IRQ_PRIOR
-	bool "Use IRQ priority"
-	help
-	  Select this if you want to use prioritized IRQ handling.
-	  This feature prevents higher priority ISR to be interrupted
-	  by lower priority IRQ even IRQF_DISABLED flag is not set.
-	  This may be useful in embedded applications, where are strong
-	  requirements for timing.
-	  Say N here, unless you have a specialized requirement.
-
-config MXC_TZIC
-	bool
-
-config MXC_AVIC
-	bool
-
-config MXC_DEBUG_BOARD
-	bool "Enable MXC debug board(for 3-stack)"
-	help
-	  The debug board is an integral part of the MXC 3-stack(PDK)
-	  platforms, it can be attached or removed from the peripheral
-	  board. On debug board, several debug devices(ethernet, UART,
-	  buttons, LEDs and JTAG) are implemented. Between the MCU and
-	  these devices, a CPLD is added as a bridge which performs
-	  data/address de-multiplexing and decode, signal level shift,
-	  interrupt control and various board functions.
-
-config HAVE_EPIT
-	bool
-
-config MXC_USE_EPIT
-	bool "Use EPIT instead of GPT"
-	depends on HAVE_EPIT
-	help
-	  Use EPIT as the system timer on systems that have it. Normally you
-	  don't have a reason to do so as the EPIT has the same features and
-	  uses the same clocks as the GPT. Anyway, on some systems the GPT
-	  may be in use for other purposes.
-
-config MXC_ULPI
-	bool
-
-config ARCH_HAS_RNGA
-	bool
-
-config IRAM_ALLOC
-	bool
-	select GENERIC_ALLOCATOR
-
-endif

arch/arm/plat-mxc/Makefile

-#
-# Makefile for the linux kernel.
-#
-
-# Common support
-obj-y := time.o cpu.o system.o irq-common.o
-
-obj-$(CONFIG_MXC_TZIC) += tzic.o
-obj-$(CONFIG_MXC_AVIC) += avic.o
-
-obj-$(CONFIG_IRAM_ALLOC) += iram_alloc.o
-obj-$(CONFIG_MXC_ULPI) += ulpi.o
-obj-$(CONFIG_MXC_USE_EPIT) += epit.o
-obj-$(CONFIG_MXC_DEBUG_BOARD) += 3ds_debugboard.o
-obj-$(CONFIG_CPU_FREQ_IMX)    += cpufreq.o
-obj-$(CONFIG_CPU_IDLE) += cpuidle.o
-ifdef CONFIG_SND_IMX_SOC
-obj-y += ssi-fiq.o
-obj-y += ssi-fiq-ksym.o
-endif