ARM: dts: bcm283x: Use GPIO polarity defines consistently

Currently most of the Raspberry Pi DTS have a mixture of magic
numbers and the proper GPIO polarity defines. So use the latter
one consistently.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>

arch/arm/boot/dts/bcm2835-rpi-a-plus.dts

@@ -10,12 +10,12 @@ / {
 
 	leds {
 		act {
-			gpios = <&gpio 47 0>;
+			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
 		};
 
 		pwr {
 			label = "PWR";
-			gpios = <&gpio 35 0>;
+			gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
 			linux,default-trigger = "default-on";
 		};

arch/arm/boot/dts/bcm2835-rpi-a.dts

@@ -10,7 +10,7 @@ / {
 
 	leds {
 		act {
-			gpios = <&gpio 16 1>;
+			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
 		};
 	};
 };

arch/arm/boot/dts/bcm2835-rpi-b-plus.dts

@@ -11,12 +11,12 @@ / {
 
 	leds {
 		act {
-			gpios = <&gpio 47 0>;
+			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
 		};
 
 		pwr {
 			label = "PWR";
-			gpios = <&gpio 35 0>;
+			gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
 			linux,default-trigger = "default-on";
 		};

arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts

@@ -11,7 +11,7 @@ / {
 
 	leds {
 		act {
-			gpios = <&gpio 16 1>;
+			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
 		};
 	};
 };

arch/arm/boot/dts/bcm2835-rpi-b.dts

@@ -11,7 +11,7 @@ / {
 
 	leds {
 		act {
-			gpios = <&gpio 16 1>;
+			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
 		};
 	};
 };

arch/arm/boot/dts/bcm2836-rpi-2-b.dts

@@ -15,12 +15,12 @@ memory {
 
 	leds {
 		act {
-			gpios = <&gpio 47 0>;
+			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
 		};
 
 		pwr {
 			label = "PWR";
-			gpios = <&gpio 35 0>;
+			gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
 			linux,default-trigger = "default-on";
 		};

arch/arm/boot/dts/bcm2837-rpi-3-b.dts

@@ -20,7 +20,7 @@ memory {
 
 	leds {
 		act {
-			gpios = <&gpio 47 0>;
+			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
 		};
 	};
 };