Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC fixes from Olof Johansson:
 "A few fixes this time around:

   - Fixup of some clock specifications for DRA7 (device-tree fix)

   - Removal of some dead/legacy CPU OPP/PM code for OMAP that throws
     warnings at boot

   - A few more minor fixups for OMAPs, most around display

   - Enable STM32 QSPI as =y since their rootfs sometimes comes from
     there

   - Switch CONFIG_REMOTEPROC to =y since it went from tristate to bool

   - Fix of thermal zone definition for ux500 (5.4 regression)"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  ARM: multi_v7_defconfig: Fix SPI_STM32_QSPI support
  ARM: dts: ux500: Fix up the CPU thermal zone
  arm64/ARM: configs: Change CONFIG_REMOTEPROC from m to y
  ARM: dts: am4372: Set memory bandwidth limit for DISPC
  ARM: OMAP2+: Fix warnings with broken omap2_set_init_voltage()
  ARM: OMAP2+: Add missing LCDC midlemode for am335x
  ARM: OMAP2+: Fix missing reset done flag for am3 and am43
  ARM: dts: Fix gpio0 flags for am335x-icev2
  ARM: omap2plus_defconfig: Enable more droid4 devices as loadable modules
  ARM: omap2plus_defconfig: Enable DRM_TI_TFP410
  DTS: ARM: gta04: introduce legacy spi-cs-high to make display work again
  ARM: dts: Fix wrong clocks for dra7 mcasp
  clk: ti: dra7: Fix mcasp8 clock bits

arch/arm/boot/dts/am335x-icev2.dts

@@ -432,7 +432,7 @@ &mmc1 {
 	pinctrl-0 = <&mmc0_pins_default>;
 };
 
-&gpio0 {
+&gpio0_target {
 	/* Do not idle the GPIO used for holding the VTT regulator */
 	ti,no-reset-on-init;
 	ti,no-idle-on-init;

arch/arm/boot/dts/am33xx-l4.dtsi

@@ -127,7 +127,7 @@ target-module@5000 {			/* 0x44e05000, ap 12 30.0 */
 			ranges = <0x0 0x5000 0x1000>;
 		};
 
-		target-module@7000 {			/* 0x44e07000, ap 14 20.0 */
+		gpio0_target: target-module@7000 {	/* 0x44e07000, ap 14 20.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
 			ti,hwmods = "gpio1";
 			reg = <0x7000 0x4>,
@@ -2038,7 +2038,9 @@ target-module@e000 {			/* 0x4830e000, ap 72 4a.0 */
 			reg = <0xe000 0x4>,
 			      <0xe054 0x4>;
 			reg-names = "rev", "sysc";
-			ti,sysc-midle ;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
 			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
 					<SYSC_IDLE_NO>,
 					<SYSC_IDLE_SMART>;

arch/arm/boot/dts/am4372.dtsi

@@ -337,6 +337,8 @@ dispc: dispc@4832a400 {
 				ti,hwmods = "dss_dispc";
 				clocks = <&disp_clk>;
 				clock-names = "fck";
+
+				max-memory-bandwidth = <230000000>;
 			};
 
 			rfbi: rfbi@4832a800 {

arch/arm/boot/dts/dra7-l4.dtsi

@@ -2732,7 +2732,7 @@ mcasp1: mcasp@0 {
 				interrupt-names = "tx", "rx";
 				dmas = <&edma_xbar 129 1>, <&edma_xbar 128 1>;
 				dma-names = "tx", "rx";
-				clocks = <&ipu_clkctrl DRA7_IPU_MCASP1_CLKCTRL 22>,
+				clocks = <&ipu_clkctrl DRA7_IPU_MCASP1_CLKCTRL 0>,
 					 <&ipu_clkctrl DRA7_IPU_MCASP1_CLKCTRL 24>,
 					 <&ipu_clkctrl DRA7_IPU_MCASP1_CLKCTRL 28>;
 				clock-names = "fck", "ahclkx", "ahclkr";
@@ -2768,8 +2768,8 @@ mcasp2: mcasp@0 {
 				interrupt-names = "tx", "rx";
 				dmas = <&edma_xbar 131 1>, <&edma_xbar 130 1>;
 				dma-names = "tx", "rx";
-				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP2_CLKCTRL 22>,
-					 <&l4per2_clkctrl DRA7_L4PER2_MCASP2_CLKCTRL 24>,
+				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP2_CLKCTRL 0>,
+					 <&ipu_clkctrl DRA7_IPU_MCASP1_CLKCTRL 24>,
 					 <&l4per2_clkctrl DRA7_L4PER2_MCASP2_CLKCTRL 28>;
 				clock-names = "fck", "ahclkx", "ahclkr";
 				status = "disabled";
@@ -2786,9 +2786,8 @@ target-module@68000 {			/* 0x48468000, ap 13 26.0 */
 					<SYSC_IDLE_SMART>;
 			/* Domains (P, C): l4per_pwrdm, l4per2_clkdm */
 			clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 0>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 24>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 28>;
-			clock-names = "fck", "ahclkx", "ahclkr";
+				 <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 24>;
+			clock-names = "fck", "ahclkx";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x68000 0x2000>,
@@ -2804,7 +2803,7 @@ mcasp3: mcasp@0 {
 				interrupt-names = "tx", "rx";
 				dmas = <&edma_xbar 133 1>, <&edma_xbar 132 1>;
 				dma-names = "tx", "rx";
-				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 22>,
+				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 0>,
 					 <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 24>;
 				clock-names = "fck", "ahclkx";
 				status = "disabled";
@@ -2821,9 +2820,8 @@ target-module@6c000 {			/* 0x4846c000, ap 15 2e.0 */
 					<SYSC_IDLE_SMART>;
 			/* Domains (P, C): l4per_pwrdm, l4per2_clkdm */
 			clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP4_CLKCTRL 0>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP4_CLKCTRL 24>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP4_CLKCTRL 28>;
-			clock-names = "fck", "ahclkx", "ahclkr";
+				 <&l4per2_clkctrl DRA7_L4PER2_MCASP4_CLKCTRL 24>;
+			clock-names = "fck", "ahclkx";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x6c000 0x2000>,
@@ -2839,7 +2837,7 @@ mcasp4: mcasp@0 {
 				interrupt-names = "tx", "rx";
 				dmas = <&edma_xbar 135 1>, <&edma_xbar 134 1>;
 				dma-names = "tx", "rx";
-				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP4_CLKCTRL 22>,
+				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP4_CLKCTRL 0>,
 					 <&l4per2_clkctrl DRA7_L4PER2_MCASP4_CLKCTRL 24>;
 				clock-names = "fck", "ahclkx";
 				status = "disabled";
@@ -2856,9 +2854,8 @@ target-module@70000 {			/* 0x48470000, ap 19 36.0 */
 					<SYSC_IDLE_SMART>;
 			/* Domains (P, C): l4per_pwrdm, l4per2_clkdm */
 			clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP5_CLKCTRL 0>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP5_CLKCTRL 24>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP5_CLKCTRL 28>;
-			clock-names = "fck", "ahclkx", "ahclkr";
+				 <&l4per2_clkctrl DRA7_L4PER2_MCASP5_CLKCTRL 24>;
+			clock-names = "fck", "ahclkx";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x70000 0x2000>,
@@ -2874,7 +2871,7 @@ mcasp5: mcasp@0 {
 				interrupt-names = "tx", "rx";
 				dmas = <&edma_xbar 137 1>, <&edma_xbar 136 1>;
 				dma-names = "tx", "rx";
-				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP5_CLKCTRL 22>,
+				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP5_CLKCTRL 0>,
 					 <&l4per2_clkctrl DRA7_L4PER2_MCASP5_CLKCTRL 24>;
 				clock-names = "fck", "ahclkx";
 				status = "disabled";
@@ -2891,9 +2888,8 @@ target-module@74000 {			/* 0x48474000, ap 35 14.0 */
 					<SYSC_IDLE_SMART>;
 			/* Domains (P, C): l4per_pwrdm, l4per2_clkdm */
 			clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP6_CLKCTRL 0>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP6_CLKCTRL 24>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP6_CLKCTRL 28>;
-			clock-names = "fck", "ahclkx", "ahclkr";
+				 <&l4per2_clkctrl DRA7_L4PER2_MCASP6_CLKCTRL 24>;
+			clock-names = "fck", "ahclkx";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x74000 0x2000>,
@@ -2909,7 +2905,7 @@ mcasp6: mcasp@0 {
 				interrupt-names = "tx", "rx";
 				dmas = <&edma_xbar 139 1>, <&edma_xbar 138 1>;
 				dma-names = "tx", "rx";
-				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP6_CLKCTRL 22>,
+				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP6_CLKCTRL 0>,
 					 <&l4per2_clkctrl DRA7_L4PER2_MCASP6_CLKCTRL 24>;
 				clock-names = "fck", "ahclkx";
 				status = "disabled";
@@ -2926,9 +2922,8 @@ target-module@78000 {			/* 0x48478000, ap 39 0c.0 */
 					<SYSC_IDLE_SMART>;
 			/* Domains (P, C): l4per_pwrdm, l4per2_clkdm */
 			clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP7_CLKCTRL 0>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP7_CLKCTRL 24>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP7_CLKCTRL 28>;
-			clock-names = "fck", "ahclkx", "ahclkr";
+				 <&l4per2_clkctrl DRA7_L4PER2_MCASP7_CLKCTRL 24>;
+			clock-names = "fck", "ahclkx";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x78000 0x2000>,
@@ -2944,7 +2939,7 @@ mcasp7: mcasp@0 {
 				interrupt-names = "tx", "rx";
 				dmas = <&edma_xbar 141 1>, <&edma_xbar 140 1>;
 				dma-names = "tx", "rx";
-				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP7_CLKCTRL 22>,
+				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP7_CLKCTRL 0>,
 					 <&l4per2_clkctrl DRA7_L4PER2_MCASP7_CLKCTRL 24>;
 				clock-names = "fck", "ahclkx";
 				status = "disabled";
@@ -2961,9 +2956,8 @@ target-module@7c000 {			/* 0x4847c000, ap 43 04.0 */
 					<SYSC_IDLE_SMART>;
 			/* Domains (P, C): l4per_pwrdm, l4per2_clkdm */
 			clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP8_CLKCTRL 0>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP8_CLKCTRL 24>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP8_CLKCTRL 28>;
-			clock-names = "fck", "ahclkx", "ahclkr";
+				 <&l4per2_clkctrl DRA7_L4PER2_MCASP8_CLKCTRL 24>;
+			clock-names = "fck", "ahclkx";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x7c000 0x2000>,
@@ -2979,7 +2973,7 @@ mcasp8: mcasp@0 {
 				interrupt-names = "tx", "rx";
 				dmas = <&edma_xbar 143 1>, <&edma_xbar 142 1>;
 				dma-names = "tx", "rx";
-				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP8_CLKCTRL 22>,
+				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP8_CLKCTRL 0>,
 					 <&l4per2_clkctrl DRA7_L4PER2_MCASP8_CLKCTRL 24>;
 				clock-names = "fck", "ahclkx";
 				status = "disabled";

arch/arm/boot/dts/omap3-gta04.dtsi

@@ -124,6 +124,7 @@ lcd: td028ttec1@0 {
 			spi-max-frequency = <100000>;
 			spi-cpol;
 			spi-cpha;
+			spi-cs-high;
 
 			backlight= <&backlight>;
 			label = "lcd";

arch/arm/boot/dts/ste-dbx5x0.dtsi

@@ -8,6 +8,7 @@
 #include <dt-bindings/mfd/dbx500-prcmu.h>
 #include <dt-bindings/arm/ux500_pm_domains.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/thermal/thermal.h>
 
 / {
 	#address-cells = <1>;
@@ -59,8 +60,12 @@ thermal-zones {
 		 * cooling.
 		 */
 		cpu_thermal: cpu-thermal {
-			polling-delay-passive = <0>;
-			polling-delay = <1000>;
+			polling-delay-passive = <250>;
+			/*
+			 * This sensor fires interrupts to update the thermal
+			 * zone, so no polling is needed.
+			 */
+			polling-delay = <0>;
 
 			thermal-sensors = <&thermal>;
 
@@ -79,7 +84,7 @@ cpu-crit {
 
 			cooling-maps {
 				trip = <&cpu_alert>;
-				cooling-device = <&CPU0 0 2>;
+				cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
 				contribution = <100>;
 			};
 		};

arch/arm/configs/davinci_all_defconfig

@@ -228,7 +228,7 @@ CONFIG_RTC_DRV_OMAP=m
 CONFIG_DMADEVICES=y
 CONFIG_TI_EDMA=y
 CONFIG_COMMON_CLK_PWM=m
-CONFIG_REMOTEPROC=m
+CONFIG_REMOTEPROC=y
 CONFIG_DA8XX_REMOTEPROC=m
 CONFIG_MEMORY=y
 CONFIG_TI_AEMIF=m

arch/arm/configs/multi_v7_defconfig

@@ -415,7 +415,7 @@ CONFIG_SPI_SH_MSIOF=m
 CONFIG_SPI_SH_HSPI=y
 CONFIG_SPI_SIRF=y
 CONFIG_SPI_STM32=m
-CONFIG_SPI_STM32_QSPI=m
+CONFIG_SPI_STM32_QSPI=y
 CONFIG_SPI_SUN4I=y
 CONFIG_SPI_SUN6I=y
 CONFIG_SPI_TEGRA114=y
@@ -933,7 +933,7 @@ CONFIG_BCM2835_MBOX=y
 CONFIG_ROCKCHIP_IOMMU=y
 CONFIG_TEGRA_IOMMU_GART=y
 CONFIG_TEGRA_IOMMU_SMMU=y
-CONFIG_REMOTEPROC=m
+CONFIG_REMOTEPROC=y
 CONFIG_ST_REMOTEPROC=m
 CONFIG_RPMSG_VIRTIO=m
 CONFIG_ASPEED_LPC_CTRL=m

arch/arm/configs/omap2plus_defconfig

@@ -364,6 +364,7 @@ CONFIG_DRM_OMAP_PANEL_TPO_TD043MTEA1=m
 CONFIG_DRM_OMAP_PANEL_NEC_NL8048HL11=m
 CONFIG_DRM_TILCDC=m
 CONFIG_DRM_PANEL_SIMPLE=m
+CONFIG_DRM_TI_TFP410=m
 CONFIG_FB=y
 CONFIG_FIRMWARE_EDID=y
 CONFIG_FB_MODE_HELPERS=y
@@ -423,6 +424,7 @@ CONFIG_USB_SERIAL_GENERIC=y
 CONFIG_USB_SERIAL_SIMPLE=m
 CONFIG_USB_SERIAL_FTDI_SIO=m
 CONFIG_USB_SERIAL_PL2303=m
+CONFIG_USB_SERIAL_OPTION=m
 CONFIG_USB_TEST=m
 CONFIG_NOP_USB_XCEIV=m
 CONFIG_AM335X_PHY_USB=m
@@ -460,6 +462,7 @@ CONFIG_MMC_SDHCI_OMAP=y
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=m
 CONFIG_LEDS_CPCAP=m
+CONFIG_LEDS_LM3532=m
 CONFIG_LEDS_GPIO=m
 CONFIG_LEDS_PCA963X=m
 CONFIG_LEDS_PWM=m
@@ -481,7 +484,7 @@ CONFIG_RTC_DRV_OMAP=m
 CONFIG_RTC_DRV_CPCAP=m
 CONFIG_DMADEVICES=y
 CONFIG_OMAP_IOMMU=y
-CONFIG_REMOTEPROC=m
+CONFIG_REMOTEPROC=y
 CONFIG_OMAP_REMOTEPROC=m
 CONFIG_WKUP_M3_RPROC=m
 CONFIG_SOC_TI=y

arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c

@@ -763,7 +763,8 @@ static struct omap_hwmod_class_sysconfig am33xx_timer_sysc = {
 	.rev_offs	= 0x0000,
 	.sysc_offs	= 0x0010,
 	.syss_offs	= 0x0014,
-	.sysc_flags	= (SYSC_HAS_SIDLEMODE | SYSC_HAS_SOFTRESET),
+	.sysc_flags	= SYSC_HAS_SIDLEMODE | SYSC_HAS_SOFTRESET |
+			  SYSC_HAS_RESET_STATUS,
 	.idlemodes	= (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART |
 			  SIDLE_SMART_WKUP),
 	.sysc_fields	= &omap_hwmod_sysc_type2,

arch/arm/mach-omap2/omap_hwmod_33xx_data.c

@@ -231,8 +231,9 @@ static struct omap_hwmod am33xx_control_hwmod = {
 static struct omap_hwmod_class_sysconfig lcdc_sysc = {
 	.rev_offs	= 0x0,
 	.sysc_offs	= 0x54,
-	.sysc_flags	= (SYSC_HAS_SIDLEMODE | SYSC_HAS_MIDLEMODE),
-	.idlemodes	= (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART),
+	.sysc_flags	= SYSC_HAS_SIDLEMODE | SYSC_HAS_MIDLEMODE,
+	.idlemodes	= SIDLE_FORCE | SIDLE_NO | SIDLE_SMART |
+			  MSTANDBY_FORCE | MSTANDBY_NO | MSTANDBY_SMART,
 	.sysc_fields	= &omap_hwmod_sysc_type2,
 };
 

arch/arm/mach-omap2/pm.c

@@ -74,83 +74,6 @@ int omap_pm_clkdms_setup(struct clockdomain *clkdm, void *unused)
 	return 0;
 }
 
-/*
- * This API is to be called during init to set the various voltage
- * domains to the voltage as per the opp table. Typically we boot up
- * at the nominal voltage. So this function finds out the rate of
- * the clock associated with the voltage domain, finds out the correct
- * opp entry and sets the voltage domain to the voltage specified
- * in the opp entry
- */
-static int __init omap2_set_init_voltage(char *vdd_name, char *clk_name,
-					 const char *oh_name)
-{
-	struct voltagedomain *voltdm;
-	struct clk *clk;
-	struct dev_pm_opp *opp;
-	unsigned long freq, bootup_volt;
-	struct device *dev;
-
-	if (!vdd_name || !clk_name || !oh_name) {
-		pr_err("%s: invalid parameters\n", __func__);
-		goto exit;
-	}
-
-	if (!strncmp(oh_name, "mpu", 3))
-		/* 
-		 * All current OMAPs share voltage rail and clock
-		 * source, so CPU0 is used to represent the MPU-SS.
-		 */
-		dev = get_cpu_device(0);
-	else
-		dev = omap_device_get_by_hwmod_name(oh_name);
-
-	if (IS_ERR(dev)) {
-		pr_err("%s: Unable to get dev pointer for hwmod %s\n",
-			__func__, oh_name);
-		goto exit;
-	}
-
-	voltdm = voltdm_lookup(vdd_name);
-	if (!voltdm) {
-		pr_err("%s: unable to get vdd pointer for vdd_%s\n",
-			__func__, vdd_name);
-		goto exit;
-	}
-
-	clk =  clk_get(NULL, clk_name);
-	if (IS_ERR(clk)) {
-		pr_err("%s: unable to get clk %s\n", __func__, clk_name);
-		goto exit;
-	}
-
-	freq = clk_get_rate(clk);
-	clk_put(clk);
-
-	opp = dev_pm_opp_find_freq_ceil(dev, &freq);
-	if (IS_ERR(opp)) {
-		pr_err("%s: unable to find boot up OPP for vdd_%s\n",
-			__func__, vdd_name);
-		goto exit;
-	}
-
-	bootup_volt = dev_pm_opp_get_voltage(opp);
-	dev_pm_opp_put(opp);
-
-	if (!bootup_volt) {
-		pr_err("%s: unable to find voltage corresponding to the bootup OPP for vdd_%s\n",
-		       __func__, vdd_name);
-		goto exit;
-	}
-
-	voltdm_scale(voltdm, bootup_volt);
-	return 0;
-
-exit:
-	pr_err("%s: unable to set vdd_%s\n", __func__, vdd_name);
-	return -EINVAL;
-}
-
 #ifdef CONFIG_SUSPEND
 static int omap_pm_enter(suspend_state_t suspend_state)
 {
@@ -208,25 +131,6 @@ void omap_common_suspend_init(void *pm_suspend)
 }
 #endif /* CONFIG_SUSPEND */
 
-static void __init omap3_init_voltages(void)
-{
-	if (!soc_is_omap34xx())
-		return;
-
-	omap2_set_init_voltage("mpu_iva", "dpll1_ck", "mpu");
-	omap2_set_init_voltage("core", "l3_ick", "l3_main");
-}
-
-static void __init omap4_init_voltages(void)
-{
-	if (!soc_is_omap44xx())
-		return;
-
-	omap2_set_init_voltage("mpu", "dpll_mpu_ck", "mpu");
-	omap2_set_init_voltage("core", "l3_div_ck", "l3_main_1");
-	omap2_set_init_voltage("iva", "dpll_iva_m5x2_ck", "iva");
-}
-
 int __maybe_unused omap_pm_nop_init(void)
 {
 	return 0;
@@ -246,10 +150,6 @@ int __init omap2_common_pm_late_init(void)
 	omap4_twl_init();
 	omap_voltage_late_init();
 
-	/* Initialize the voltages */
-	omap3_init_voltages();
-	omap4_init_voltages();
-
 	/* Smartreflex device init */
 	omap_devinit_smartreflex();
 

arch/arm64/configs/defconfig

@@ -723,7 +723,7 @@ CONFIG_TEGRA_IOMMU_SMMU=y
 CONFIG_ARM_SMMU=y
 CONFIG_ARM_SMMU_V3=y
 CONFIG_QCOM_IOMMU=y
-CONFIG_REMOTEPROC=m
+CONFIG_REMOTEPROC=y
 CONFIG_QCOM_Q6V5_MSS=m
 CONFIG_QCOM_Q6V5_PAS=m
 CONFIG_QCOM_SYSMON=m

drivers/clk/ti/clk-7xx.c

@@ -683,7 +683,7 @@ static const struct omap_clkctrl_reg_data dra7_l4per2_clkctrl_regs[] __initconst
 	{ DRA7_L4PER2_MCASP2_CLKCTRL, dra7_mcasp2_bit_data, CLKF_SW_SUP, "l4per2-clkctrl:0154:22" },
 	{ DRA7_L4PER2_MCASP3_CLKCTRL, dra7_mcasp3_bit_data, CLKF_SW_SUP, "l4per2-clkctrl:015c:22" },
 	{ DRA7_L4PER2_MCASP5_CLKCTRL, dra7_mcasp5_bit_data, CLKF_SW_SUP, "l4per2-clkctrl:016c:22" },
-	{ DRA7_L4PER2_MCASP8_CLKCTRL, dra7_mcasp8_bit_data, CLKF_SW_SUP, "l4per2-clkctrl:0184:24" },
+	{ DRA7_L4PER2_MCASP8_CLKCTRL, dra7_mcasp8_bit_data, CLKF_SW_SUP, "l4per2-clkctrl:0184:22" },
 	{ DRA7_L4PER2_MCASP4_CLKCTRL, dra7_mcasp4_bit_data, CLKF_SW_SUP, "l4per2-clkctrl:018c:22" },
 	{ DRA7_L4PER2_UART7_CLKCTRL, dra7_uart7_bit_data, CLKF_SW_SUP, "l4per2-clkctrl:01c4:24" },
 	{ DRA7_L4PER2_UART8_CLKCTRL, dra7_uart8_bit_data, CLKF_SW_SUP, "l4per2-clkctrl:01d4:24" },
@@ -828,8 +828,8 @@ static struct ti_dt_clk dra7xx_clks[] = {
 	DT_CLK(NULL, "mcasp6_aux_gfclk_mux", "l4per2-clkctrl:01f8:22"),
 	DT_CLK(NULL, "mcasp7_ahclkx_mux", "l4per2-clkctrl:01fc:24"),
 	DT_CLK(NULL, "mcasp7_aux_gfclk_mux", "l4per2-clkctrl:01fc:22"),
-	DT_CLK(NULL, "mcasp8_ahclkx_mux", "l4per2-clkctrl:0184:22"),
-	DT_CLK(NULL, "mcasp8_aux_gfclk_mux", "l4per2-clkctrl:0184:24"),
+	DT_CLK(NULL, "mcasp8_ahclkx_mux", "l4per2-clkctrl:0184:24"),
+	DT_CLK(NULL, "mcasp8_aux_gfclk_mux", "l4per2-clkctrl:0184:22"),
 	DT_CLK(NULL, "mmc1_clk32k", "l3init-clkctrl:0008:8"),
 	DT_CLK(NULL, "mmc1_fclk_div", "l3init-clkctrl:0008:25"),
 	DT_CLK(NULL, "mmc1_fclk_mux", "l3init-clkctrl:0008:24"),