dt: Remove booting-without-of.rst

booting-without-of.rst is an ancient document that first outlined
Flattened DeviceTree on PowerPC initially. The DT world has evolved a
lot in the 15 years since and booting-without-of.rst is pretty stale.
The name of the document itself is confusing if you don't understand the
evolution from real 'OpenFirmware'. Most of what booting-without-of.rst
contains is now in the DT specification (which evolved out of the
ePAPR). The few things that weren't documented in the DT specification
are now.

All that remains is the boot entry details, so let's move these to arch
specific documents. The exception is arm which already has the same
details documented.

Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-mips@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Rob Herring <robh@kernel.org>

Documentation/devicetree/index.rst

@@ -15,4 +15,3 @@ Open Firmware and Device Tree
    overlay-notes
 
    bindings/index
-   booting-without-of

Documentation/mips/booting.rst

+.. SPDX-License-Identifier: GPL-2.0
+
+BMIPS DeviceTree Booting
+------------------------
+
+  Some bootloaders only support a single entry point, at the start of the
+  kernel image.  Other bootloaders will jump to the ELF start address.
+  Both schemes are supported; CONFIG_BOOT_RAW=y and CONFIG_NO_EXCEPT_FILL=y,
+  so the first instruction immediately jumps to kernel_entry().
+
+  Similar to the arch/arm case (b), a DT-aware bootloader is expected to
+  set up the following registers:
+
+         a0 : 0
+
+         a1 : 0xffffffff
+
+         a2 : Physical pointer to the device tree block (defined in chapter
+         II) in RAM.  The device tree can be located anywhere in the first
+         512MB of the physical address space (0x00000000 - 0x1fffffff),
+         aligned on a 64 bit boundary.
+
+  Legacy bootloaders do not use this convention, and they do not pass in a
+  DT block.  In this case, Linux will look for a builtin DTB, selected via
+  CONFIG_DT_*.
+
+  This convention is defined for 32-bit systems only, as there are not
+  currently any 64-bit BMIPS implementations.

Documentation/mips/index.rst

@@ -8,6 +8,7 @@ MIPS-specific Documentation
    :maxdepth: 2
    :numbered:
 
+   booting
    ingenic-tcu
 
 .. only::  subproject and html

Documentation/powerpc/booting.rst

+.. SPDX-License-Identifier: GPL-2.0
+
+DeviceTree Booting
+------------------
+
+During the development of the Linux/ppc64 kernel, and more specifically, the
+addition of new platform types outside of the old IBM pSeries/iSeries pair, it
+was decided to enforce some strict rules regarding the kernel entry and
+bootloader <-> kernel interfaces, in order to avoid the degeneration that had
+become the ppc32 kernel entry point and the way a new platform should be added
+to the kernel. The legacy iSeries platform breaks those rules as it predates
+this scheme, but no new board support will be accepted in the main tree that
+doesn't follow them properly.  In addition, since the advent of the arch/powerpc
+merged architecture for ppc32 and ppc64, new 32-bit platforms and 32-bit
+platforms which move into arch/powerpc will be required to use these rules as
+well.
+
+The main requirement that will be defined in more detail below is the presence
+of a device-tree whose format is defined after Open Firmware specification.
+However, in order to make life easier to embedded board vendors, the kernel
+doesn't require the device-tree to represent every device in the system and only
+requires some nodes and properties to be present. For example, the kernel does
+not require you to create a node for every PCI device in the system. It is a
+requirement to have a node for PCI host bridges in order to provide interrupt
+routing information and memory/IO ranges, among others. It is also recommended
+to define nodes for on chip devices and other buses that don't specifically fit
+in an existing OF specification. This creates a great flexibility in the way the
+kernel can then probe those and match drivers to device, without having to hard
+code all sorts of tables. It also makes it more flexible for board vendors to do
+minor hardware upgrades without significantly impacting the kernel code or
+cluttering it with special cases.
+
+
+Entry point
+~~~~~~~~~~~
+
+There is one single entry point to the kernel, at the start
+of the kernel image. That entry point supports two calling
+conventions:
+
+        a) Boot from Open Firmware. If your firmware is compatible
+        with Open Firmware (IEEE 1275) or provides an OF compatible
+        client interface API (support for "interpret" callback of
+        forth words isn't required), you can enter the kernel with:
+
+              r5 : OF callback pointer as defined by IEEE 1275
+              bindings to powerpc. Only the 32-bit client interface
+              is currently supported
+
+              r3, r4 : address & length of an initrd if any or 0
+
+              The MMU is either on or off; the kernel will run the
+              trampoline located in arch/powerpc/kernel/prom_init.c to
+              extract the device-tree and other information from open
+              firmware and build a flattened device-tree as described
+              in b). prom_init() will then re-enter the kernel using
+              the second method. This trampoline code runs in the
+              context of the firmware, which is supposed to handle all
+              exceptions during that time.
+
+        b) Direct entry with a flattened device-tree block. This entry
+        point is called by a) after the OF trampoline and can also be
+        called directly by a bootloader that does not support the Open
+        Firmware client interface. It is also used by "kexec" to
+        implement "hot" booting of a new kernel from a previous
+        running one. This method is what I will describe in more
+        details in this document, as method a) is simply standard Open
+        Firmware, and thus should be implemented according to the
+        various standard documents defining it and its binding to the
+        PowerPC platform. The entry point definition then becomes:
+
+                r3 : physical pointer to the device-tree block
+                (defined in chapter II) in RAM
+
+                r4 : physical pointer to the kernel itself. This is
+                used by the assembly code to properly disable the MMU
+                in case you are entering the kernel with MMU enabled
+                and a non-1:1 mapping.
+
+                r5 : NULL (as to differentiate with method a)
+
+Note about SMP entry: Either your firmware puts your other
+CPUs in some sleep loop or spin loop in ROM where you can get
+them out via a soft reset or some other means, in which case
+you don't need to care, or you'll have to enter the kernel
+with all CPUs. The way to do that with method b) will be
+described in a later revision of this document.
+
+Board supports (platforms) are not exclusive config options. An
+arbitrary set of board supports can be built in a single kernel
+image. The kernel will "know" what set of functions to use for a
+given platform based on the content of the device-tree. Thus, you
+should:
+
+        a) add your platform support as a _boolean_ option in
+        arch/powerpc/Kconfig, following the example of PPC_PSERIES,
+        PPC_PMAC and PPC_MAPLE. The later is probably a good
+        example of a board support to start from.
+
+        b) create your main platform file as
+        "arch/powerpc/platforms/myplatform/myboard_setup.c" and add it
+        to the Makefile under the condition of your ``CONFIG_``
+        option. This file will define a structure of type "ppc_md"
+        containing the various callbacks that the generic code will
+        use to get to your platform specific code
+
+A kernel image may support multiple platforms, but only if the
+platforms feature the same core architecture.  A single kernel build
+cannot support both configurations with Book E and configurations
+with classic Powerpc architectures.

Documentation/powerpc/index.rst

@@ -7,6 +7,7 @@ powerpc
 .. toctree::
     :maxdepth: 1
 
+    booting
     bootwrapper
     cpu_families
     cpu_features

Documentation/sh/booting.rst

+.. SPDX-License-Identifier: GPL-2.0
+
+DeviceTree Booting
+------------------
+
+  Device-tree compatible SH bootloaders are expected to provide the physical
+  address of the device tree blob in r4. Since legacy bootloaders did not
+  guarantee any particular initial register state, kernels built to
+  inter-operate with old bootloaders must either use a builtin DTB or
+  select a legacy board option (something other than CONFIG_SH_DEVICE_TREE)
+  that does not use device tree. Support for the latter is being phased out
+  in favor of device tree.

Documentation/sh/index.rst

@@ -7,6 +7,7 @@ SuperH Interfaces Guide
 .. toctree::
     :maxdepth: 1
 
+    booting
     new-machine
     register-banks
 

Documentation/x86/booting-dt.rst

+.. SPDX-License-Identifier: GPL-2.0
+
+DeviceTree Booting
+------------------
+
+  There is one single 32bit entry point to the kernel at code32_start,
+  the decompressor (the real mode entry point goes to the same  32bit
+  entry point once it switched into protected mode). That entry point
+  supports one calling convention which is documented in
+  Documentation/x86/boot.rst
+  The physical pointer to the device-tree block is passed via setup_data
+  which requires at least boot protocol 2.09.
+  The type filed is defined as
+
+  #define SETUP_DTB                      2
+
+  This device-tree is used as an extension to the "boot page". As such it
+  does not parse / consider data which is already covered by the boot
+  page. This includes memory size, reserved ranges, command line arguments
+  or initrd address. It simply holds information which can not be retrieved
+  otherwise like interrupt routing or a list of devices behind an I2C bus.

Documentation/x86/index.rst

@@ -9,6 +9,7 @@ x86-specific Documentation
    :numbered:
 
    boot
+   booting-dt
    topology
    exception-tables
    kernel-stacks