ARM: dts: omap*: Replace deprecated "vmmc_aux" with "vqmmc"

Replace deprecated "vmmc_aux" with the generic "vqmmc" binding for
MMC IO supply.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

arch/arm/boot/dts/am572x-idk.dts

@@ -79,7 +79,7 @@ &extcon_usb2 {
 &mmc1 {
 	status = "okay";
 	vmmc-supply = <&v3_3d>;
-	vmmc_aux-supply = <&ldo1_reg>;
+	vqmmc-supply = <&ldo1_reg>;
 	bus-width = <4>;
 	cd-gpios = <&gpio6 27 0>; /* gpio 219 */
 };

arch/arm/boot/dts/dra7-evm.dts

@@ -446,7 +446,7 @@ &mmc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins_default>;
 	vmmc-supply = <&evm_3v3_sd>;
-	vmmc_aux-supply = <&ldo1_reg>;
+	vqmmc-supply = <&ldo1_reg>;
 	bus-width = <4>;
 	/*
 	 * SDCD signal is not being used here - using the fact that GPIO mode

arch/arm/boot/dts/dra71-evm.dts

@@ -172,7 +172,7 @@ p0 {
 };
 
 &mmc1 {
-	vmmc_aux-supply = <&vpo_sd_1v8_3v3>;
+	vqmmc-supply = <&vpo_sd_1v8_3v3>;
 };
 
 &mmc2 {

arch/arm/boot/dts/dra72-evm-tps65917.dtsi

@@ -146,5 +146,5 @@ &dss {
 };
 
 &mmc1 {
-	vmmc_aux-supply = <&ldo1_reg>;
+	vqmmc-supply = <&ldo1_reg>;
 };

arch/arm/boot/dts/omap3-beagle-xm.dts

@@ -299,7 +299,7 @@ &i2c3 {
 
 &mmc1 {
 	vmmc-supply = <&vmmc1>;
-	vmmc_aux-supply = <&vsim>;
+	vqmmc-supply = <&vsim>;
 	bus-width = <8>;
 };
 

arch/arm/boot/dts/omap3-beagle.dts

@@ -283,7 +283,7 @@ &i2c3 {
 
 &mmc1 {
 	vmmc-supply = <&vmmc1>;
-	vmmc_aux-supply = <&vsim>;
+	vqmmc-supply = <&vsim>;
 	bus-width = <8>;
 };
 

arch/arm/boot/dts/omap3-cm-t3517.dts

@@ -129,7 +129,7 @@ &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_pins>;
 	vmmc-supply = <&wl12xx_vmmc2>;
-	vmmc_aux-supply = <&wl12xx_vaux2>;
+	vqmmc-supply = <&wl12xx_vaux2>;
 	non-removable;
 	bus-width = <4>;
 	cap-power-off-card;

arch/arm/boot/dts/omap3-cm-t3730.dts

@@ -69,7 +69,7 @@ &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_pins>;
 	vmmc-supply = <&wl12xx_vmmc2>;
-	vmmc_aux-supply = <&wl12xx_vaux2>;
+	vqmmc-supply = <&wl12xx_vaux2>;
 	non-removable;
 	bus-width = <4>;
 	cap-power-off-card;

arch/arm/boot/dts/omap3-devkit8000-common.dtsi

@@ -149,7 +149,7 @@ &i2c3 {
 
 &mmc1 {
 	vmmc-supply = <&vmmc1>;
-	vmmc_aux-supply = <&vsim>;
+	vqmmc-supply = <&vsim>;
 	bus-width = <8>;
 };
 

arch/arm/boot/dts/omap3-evm-common.dtsi

@@ -115,7 +115,7 @@ tsc2046@0 {
 &mmc1 {
 	interrupts-extended = <&intc 83 &omap3_pmx_core 0x11a>;
 	vmmc-supply = <&vmmc1>;
-	vmmc_aux-supply = <&vsim>;
+	vqmmc-supply = <&vsim>;
 	bus-width = <8>;
 };
 

arch/arm/boot/dts/omap3-n900.dts

@@ -741,7 +741,7 @@ &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_pins>;
 	vmmc-supply = <&vaux3>;
-	vmmc_aux-supply = <&vsim>;
+	vqmmc-supply = <&vsim>;
 	bus-width = <8>;
 	non-removable;
 	no-sdio;

arch/arm/boot/dts/omap3-overo-base.dtsi

@@ -181,7 +181,7 @@ &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_pins>;
 	vmmc-supply = <&w3cbw003c_npoweron>;
-	vmmc_aux-supply = <&w3cbw003c_wifi_nreset>;
+	vqmmc-supply = <&w3cbw003c_wifi_nreset>;
 	bus-width = <4>;
 	cap-sdio-irq;
 	non-removable;

arch/arm/boot/dts/omap3-tao3530.dtsi

@@ -223,7 +223,7 @@ &mmc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins>;
 	vmmc-supply = <&vmmc1>;
-	vmmc_aux-supply = <&vsim>;
+	vqmmc-supply = <&vsim>;
 	cd-gpios = <&twl_gpio 0 GPIO_ACTIVE_HIGH>;
 	bus-width = <8>;
 };

arch/arm/boot/dts/omap3-zoom3.dts

@@ -174,7 +174,7 @@ &twl_gpio {
 
 &mmc1 {
 	vmmc-supply = <&vmmc1>;
-	vmmc_aux-supply = <&vsim>;
+	vqmmc-supply = <&vsim>;
 	bus-width = <4>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins>;

arch/arm/boot/dts/omap3430-sdp.dts

@@ -33,7 +33,7 @@ twl: twl@48 {
 
 &mmc1 {
 	vmmc-supply = <&vmmc1>;
-	vmmc_aux-supply = <&vsim>;
+	vqmmc-supply = <&vsim>;
 	/*
 	 * S6-3 must be in ON position for 8 bit mode to function
 	 * Else, use 4 bit mode