ARM: 9005/1: debug: Select flow control for all debug UARTs

Instead of a flow control selection mechanism specifically for
8250, make this available for all debug UARTs. If the debug
UART supports waiting for CTS to be asserted, then this code
can be activated for terminals that need it.

We keep the defaults for EBSA110, Footbridge, Gemini and RPC
so that this still works as expected for these older platforms:
they assume that flow control shall be enabled for debug
prints.

I switch the location of the check for
ifdef CONFIG_DEBUG_UART_FLOW_CONTROL from the actual debug
UART drivers: the code would get compiled-out for 8250 and
Tegra unless their custom config (or passing -DFLOW_CONTROL
in the Tegra case) was not set. Instead this is conditional
at the three places where we print debug messages. The idea
is that debug UARTs can be implemented without this ifdef
boilerplate so they look cleaner, alas the ifdef has to be
somewhere.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

arch/arm/Kconfig.debug

@@ -1546,6 +1546,17 @@ config DEBUG_SIRFSOC_UART
 	bool
 	depends on ARCH_SIRF
 
+config DEBUG_UART_FLOW_CONTROL
+	bool "Enable flow control (CTS) for the debug UART"
+	depends on DEBUG_LL
+	default y if ARCH_EBSA110 || DEBUG_FOOTBRIDGE_COM1 || DEBUG_GEMINI || ARCH_RPC
+	help
+	  Some UART ports are connected to terminals that will use modem
+	  control signals to indicate whether they are ready to receive text.
+	  In practice this means that the terminal is asserting the special
+	  control signal CTS (Clear To Send). If your debug UART supports
+	  this and your debug terminal will require it, enable this option.
+
 config DEBUG_LL_INCLUDE
 	string
 	default "debug/sa1100.S" if DEBUG_SA1100
@@ -1893,11 +1904,6 @@ config DEBUG_UART_8250_PALMCHIP
 	  except for having a different register layout.  Say Y here if
 	  the debug UART is of this type.
 
-config DEBUG_UART_8250_FLOW_CONTROL
-	bool "Enable flow control for 8250 UART"
-	depends on DEBUG_LL_UART_8250 || DEBUG_UART_8250
-	default y if ARCH_EBSA110 || DEBUG_FOOTBRIDGE_COM1 || DEBUG_GEMINI || ARCH_RPC
-
 config DEBUG_UNCOMPRESS
 	bool "Enable decompressor debugging via DEBUG_LL output"
 	depends on ARCH_MULTIPLATFORM || PLAT_SAMSUNG || ARM_SINGLE_ARMV7M

arch/arm/boot/compressed/debug.S

@@ -8,7 +8,9 @@
 
 ENTRY(putc)
 	addruart r1, r2, r3
+#ifdef CONFIG_DEBUG_UART_FLOW_CONTROL
 	waituartcts r3, r1
+#endif
 	waituarttxrdy r3, r1
 	senduart r0, r1
 	busyuart r3, r1

arch/arm/include/debug/8250.S

@@ -49,9 +49,7 @@
 		.endm
 
 		.macro	waituartcts,rd,rx
-#ifdef CONFIG_DEBUG_UART_8250_FLOW_CONTROL
 1001:		load	\rd, [\rx, #UART_MSR << UART_SHIFT]
 		tst	\rd, #UART_MSR_CTS
 		beq	1001b
-#endif
 		.endm

arch/arm/include/debug/tegra.S

@@ -179,14 +179,12 @@
 		.endm
 
 		.macro	waituartcts, rd, rx
-#ifdef FLOW_CONTROL
 		cmp	\rx, #0
 		beq	1002f
 1001:		ldrb	\rd, [\rx, #UART_MSR << UART_SHIFT]
 		tst	\rd, #UART_MSR_CTS
 		beq	1001b
 1002:
-#endif
 		.endm
 
 		.macro	waituarttxrdy,rd,rx

arch/arm/kernel/debug.S

@@ -89,12 +89,17 @@ ENTRY(printascii)
 2:		teq     r1, #'\n'
 		bne	3f
 		mov	r1, #'\r'
+#ifdef CONFIG_DEBUG_UART_FLOW_CONTROL
 		waituartcts r2, r3
+#endif
 		waituarttxrdy r2, r3
 		senduart r1, r3
 		busyuart r2, r3
 		mov	r1, #'\n'
-3:		waituartcts r2, r3
+3:
+#ifdef CONFIG_DEBUG_UART_FLOW_CONTROL
+		waituartcts r2, r3
+#endif
 		waituarttxrdy r2, r3
 		senduart r1, r3
 		busyuart r2, r3