ARM: OMAP4+: PRM: add support for passing status register/bit info to reset

AM43xx has slightly different reset register layout compared to OMAP4+,
with varying status bit shifts and status register offsets. Current
code assumes static offsets and identical status / reset control bit
shifts, which is wrong. This patch adds PRM core support for passing
the actual implementations from hwmod code. AM43xx mappings will be fixed
in subsequent patch.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Dave Gerlach <d-gerlach@ti.com>
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

arch/arm/mach-omap2/omap_hwmod.c

@@ -171,6 +171,12 @@
  */
 #define LINKS_PER_OCP_IF		2
 
+/*
+ * Address offset (in bytes) between the reset control and the reset
+ * status registers: 4 bytes on OMAP4
+ */
+#define OMAP4_RST_CTRL_ST_OFFSET	4
+
 /**
  * struct omap_hwmod_soc_ops - fn ptrs for some SoC-specific operations
  * @enable_module: function to enable a module (via MODULEMODE)
@@ -3016,10 +3022,12 @@ static int _omap4_deassert_hardreset(struct omap_hwmod *oh,
 	if (ohri->st_shift)
 		pr_err("omap_hwmod: %s: %s: hwmod data error: OMAP4 does not support st_shift\n",
 		       oh->name, ohri->name);
-	return omap_prm_deassert_hardreset(ohri->rst_shift, 0,
+	return omap_prm_deassert_hardreset(ohri->rst_shift, ohri->rst_shift,
 					   oh->clkdm->pwrdm.ptr->prcm_partition,
 					   oh->clkdm->pwrdm.ptr->prcm_offs,
-					   oh->prcm.omap4.rstctrl_offs, 0);
+					   oh->prcm.omap4.rstctrl_offs,
+					   oh->prcm.omap4.rstctrl_offs +
+					   OMAP4_RST_CTRL_ST_OFFSET);
 }
 
 /**

arch/arm/mach-omap2/prminst44xx.c

@@ -87,12 +87,6 @@ u32 omap4_prminst_rmw_inst_reg_bits(u32 mask, u32 bits, u8 part, s16 inst,
 	return v;
 }
 
-/*
- * Address offset (in bytes) between the reset control and the reset
- * status registers: 4 bytes on OMAP4
- */
-#define OMAP4_RST_CTRL_ST_OFFSET		4
-
 /**
  * omap4_prminst_is_hardreset_asserted - read the HW reset line state of
  * submodules contained in the hwmod module
@@ -141,11 +135,11 @@ int omap4_prminst_assert_hardreset(u8 shift, u8 part, s16 inst,
  * omap4_prminst_deassert_hardreset - deassert a submodule hardreset line and
  * wait
  * @shift: register bit shift corresponding to the reset line to deassert
- * @st_shift: status bit offset, not used for OMAP4+
+ * @st_shift: status bit offset corresponding to the reset line
  * @part: PRM partition
  * @inst: PRM instance offset
  * @rstctrl_offs: reset register offset
- * @st_offs: reset status register offset, not used for OMAP4+
+ * @rstst_offs: reset status register offset
  *
  * Some IPs like dsp, ipu or iva contain processors that require an HW
  * reset line to be asserted / deasserted in order to fully enable the
@@ -157,11 +151,11 @@ int omap4_prminst_assert_hardreset(u8 shift, u8 part, s16 inst,
  * of reset, or -EBUSY if the submodule did not exit reset promptly.
  */
 int omap4_prminst_deassert_hardreset(u8 shift, u8 st_shift, u8 part, s16 inst,
-				     u16 rstctrl_offs, u16 st_offs)
+				     u16 rstctrl_offs, u16 rstst_offs)
 {
 	int c;
 	u32 mask = 1 << shift;
-	u16 rstst_offs = rstctrl_offs + OMAP4_RST_CTRL_ST_OFFSET;
+	u32 st_mask = 1 << st_shift;
 
 	/* Check the current status to avoid de-asserting the line twice */
 	if (omap4_prminst_is_hardreset_asserted(shift, part, inst,
@@ -169,13 +163,13 @@ int omap4_prminst_deassert_hardreset(u8 shift, u8 st_shift, u8 part, s16 inst,
 		return -EEXIST;
 
 	/* Clear the reset status by writing 1 to the status bit */
-	omap4_prminst_rmw_inst_reg_bits(0xffffffff, mask, part, inst,
+	omap4_prminst_rmw_inst_reg_bits(0xffffffff, st_mask, part, inst,
 					rstst_offs);
 	/* de-assert the reset control line */
 	omap4_prminst_rmw_inst_reg_bits(mask, 0, part, inst, rstctrl_offs);
 	/* wait the status to be set */
-	omap_test_timeout(omap4_prminst_is_hardreset_asserted(shift, part, inst,
-							      rstst_offs),
+	omap_test_timeout(omap4_prminst_is_hardreset_asserted(st_shift, part,
+							      inst, rstst_offs),
 			  MAX_MODULE_HARDRESET_WAIT, c);
 
 	return (c == MAX_MODULE_HARDRESET_WAIT) ? -EBUSY : 0;