Commit 67df7784 authored by Srikar Dronamraju's avatar Srikar Dronamraju Committed by Michael Ellerman

powerpc/numa: Restrict possible nodes based on platform

As per draft LoPAPR (Revision 2.9_pre7), section B.5.3 "Run Time
Abstraction Services (RTAS) Node" available at:
  https://openpowerfoundation.org/wp-content/uploads/2020/07/LoPAR-20200611.pdf

... there are 2 device tree properties:

  "ibm,max-associativity-domains"
   which defines the maximum number of domains that the firmware i.e
   PowerVM can support.

and:

  "ibm,current-associativity-domains"
   which defines the maximum number of domains that the current
   platform can support.

The value of "ibm,max-associativity-domains" is always greater than or
equal to "ibm,current-associativity-domains" property. If the latter
property is not available, use "ibm,max-associativity-domain" as a
fallback. In this yet to be released LoPAPR, "ibm,current-associativity-domains"
is mentioned in page 833 / B.5.3 which is covered under under
"Appendix B. System Binding" section

Currently powerpc uses the "ibm,max-associativity-domains" property
while setting the possible number of nodes. This is currently set at
32. However the possible number of nodes for a platform may be
significantly less. Hence set the possible number of nodes based on
"ibm,current-associativity-domains" property.

Nathan Lynch had raised a valid concern that post LPM (Live Partition
Migration), a user could DLPAR add processors and memory after LPM
with "new" associativity properties:
  https://lore.kernel.org/linuxppc-dev/871rljfet9.fsf@linux.ibm.com/t/#u

He also pointed out that "ibm,max-associativity-domains" has the same
contents on all currently available PowerVM systems, unlike
"ibm,current-associativity-domains" and hence may be better able to
handle the new NUMA associativity properties.

However with the recent commit dbce4562 ("powerpc/numa: Limit
possible nodes to within num_possible_nodes"), all new NUMA
associativity properties are capped to initially set nr_node_ids.
Hence this commit should be safe with any new DLPAR add post LPM.

  $ lsprop /proc/device-tree/rtas/ibm,*associ*-domains
  /proc/device-tree/rtas/ibm,current-associativity-domains
  		 00000005 00000001 00000002 00000002 00000002 00000010
  /proc/device-tree/rtas/ibm,max-associativity-domains
  		 00000005 00000001 00000008 00000020 00000020 00000100

  $ cat /sys/devices/system/node/possible ##Before patch
  0-31

  $ cat /sys/devices/system/node/possible ##After patch
  0-1

Note the maximum nodes this platform can support is only 2 but the
possible nodes is set to 32.

This is important because lot of kernel and user space code allocate
structures for all possible nodes leading to a lot of memory that is
allocated but not used.

I ran a simple experiment to create and destroy 100 memory cgroups on
boot on a 8 node machine (Power8 Alpine).

Before patch:
  free -k at boot
                total        used        free      shared  buff/cache   available
  Mem:      523498176     4106816   518820608       22272      570752   516606720
  Swap:       4194240           0     4194240

  free -k after creating 100 memory cgroups
                total        used        free      shared  buff/cache   available
  Mem:      523498176     4628416   518246464       22336      623296   516058688
  Swap:       4194240           0     4194240

  free -k after destroying 100 memory cgroups
                total        used        free      shared  buff/cache   available
  Mem:      523498176     4697408   518173760       22400      627008   515987904
  Swap:       4194240           0     4194240

After patch:
  free -k at boot
                total        used        free      shared  buff/cache   available
  Mem:      523498176     3969472   518933888       22272      594816   516731776
  Swap:       4194240           0     4194240

  free -k after creating 100 memory cgroups
                total        used        free      shared  buff/cache   available
  Mem:      523498176     4181888   518676096       22208      640192   516496448
  Swap:       4194240           0     4194240

  free -k after destroying 100 memory cgroups
                total        used        free      shared  buff/cache   available
  Mem:      523498176     4232320   518619904       22272      645952   516443264
  Swap:       4194240           0     4194240

Observations:
  Fixed kernel takes 137344 kb (4106816-3969472) less to boot.
  Fixed kernel takes 309184 kb (4628416-4181888-137344) less to create 100 memcgs.
Signed-off-by: default avatarSrikar Dronamraju <srikar@linux.vnet.ibm.com>
[mpe: Reformat change log a bit for readability]
Signed-off-by: default avatarMichael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200817055257.110873-1-srikar@linux.vnet.ibm.com
parent f3232321
...@@ -900,10 +900,19 @@ static void __init find_possible_nodes(void) ...@@ -900,10 +900,19 @@ static void __init find_possible_nodes(void)
if (!rtas) if (!rtas)
return; return;
if (of_property_read_u32_index(rtas, if (of_property_read_u32_index(rtas, "ibm,current-associativity-domains",
"ibm,max-associativity-domains", min_common_depth, &numnodes)) {
/*
* ibm,current-associativity-domains is a fairly recent
* property. If it doesn't exist, then fallback on
* ibm,max-associativity-domains. Current denotes what the
* platform can support compared to max which denotes what the
* Hypervisor can support.
*/
if (of_property_read_u32_index(rtas, "ibm,max-associativity-domains",
min_common_depth, &numnodes)) min_common_depth, &numnodes))
goto out; goto out;
}
for (i = 0; i < numnodes; i++) { for (i = 0; i < numnodes; i++) {
if (!node_possible(i)) if (!node_possible(i))
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment