Revert "net: bcmgenet: soft reset 40nm EPHYs before MAC init"

This reverts commit 1f515486.

This commit improved the chances of the umac resetting cleanly by
ensuring that the PHY was restored to its normal operation prior
to resetting the umac. However, there were still cases when the
PHY might not be driving a Tx clock to the umac during this window
(e.g. when the PHY detects no link).

The previous commit now ensures that the unimac receives clocks
from the MAC during its reset window so this commit is no longer
needed. This commit also has an unintended negative impact on the
MDIO performance of the UniMAC MDIO interface because it is used
before the MDIO interrupts are reenabled, so it should be removed.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/broadcom/genet/bcmgenet.c

@@ -2877,12 +2877,6 @@ static int bcmgenet_open(struct net_device *dev)
 	if (priv->internal_phy)
 		bcmgenet_power_up(priv, GENET_POWER_PASSIVE);
 
-	ret = bcmgenet_mii_connect(dev);
-	if (ret) {
-		netdev_err(dev, "failed to connect to PHY\n");
-		goto err_clk_disable;
-	}
-
 	/* take MAC out of reset */
 	bcmgenet_umac_reset(priv);
 
@@ -2892,12 +2886,6 @@ static int bcmgenet_open(struct net_device *dev)
 	reg = bcmgenet_umac_readl(priv, UMAC_CMD);
 	priv->crc_fwd_en = !!(reg & CMD_CRC_FWD);
 
-	ret = bcmgenet_mii_config(dev, true);
-	if (ret) {
-		netdev_err(dev, "unsupported PHY\n");
-		goto err_disconnect_phy;
-	}
-
 	bcmgenet_set_hw_addr(priv, dev->dev_addr);
 
 	if (priv->internal_phy) {
@@ -2913,7 +2901,7 @@ static int bcmgenet_open(struct net_device *dev)
 	ret = bcmgenet_init_dma(priv);
 	if (ret) {
 		netdev_err(dev, "failed to initialize DMA\n");
-		goto err_disconnect_phy;
+		goto err_clk_disable;
 	}
 
 	/* Always enable ring 16 - descriptor ring */
@@ -2936,19 +2924,25 @@ static int bcmgenet_open(struct net_device *dev)
 		goto err_irq0;
 	}
 
+	ret = bcmgenet_mii_probe(dev);
+	if (ret) {
+		netdev_err(dev, "failed to connect to PHY\n");
+		goto err_irq1;
+	}
+
 	bcmgenet_netif_start(dev);
 
 	netif_tx_start_all_queues(dev);
 
 	return 0;
 
+err_irq1:
+	free_irq(priv->irq1, priv);
 err_irq0:
 	free_irq(priv->irq0, priv);
 err_fini_dma:
 	bcmgenet_dma_teardown(priv);
 	bcmgenet_fini_dma(priv);
-err_disconnect_phy:
-	phy_disconnect(dev->phydev);
 err_clk_disable:
 	if (priv->internal_phy)
 		bcmgenet_power_down(priv, GENET_POWER_PASSIVE);
@@ -3629,8 +3623,6 @@ static int bcmgenet_resume(struct device *d)
 	if (priv->internal_phy)
 		bcmgenet_power_up(priv, GENET_POWER_PASSIVE);
 
-	phy_init_hw(dev->phydev);
-
 	bcmgenet_umac_reset(priv);
 
 	init_umac(priv);
@@ -3639,6 +3631,8 @@ static int bcmgenet_resume(struct device *d)
 	if (priv->wolopts)
 		clk_disable_unprepare(priv->clk_wol);
 
+	phy_init_hw(dev->phydev);
+
 	/* Speed settings must be restored */
 	bcmgenet_mii_config(priv->dev, false);
 

drivers/net/ethernet/broadcom/genet/bcmgenet.h

@@ -720,8 +720,8 @@ GENET_IO_MACRO(rbuf, GENET_RBUF_OFF);
 
 /* MDIO routines */
 int bcmgenet_mii_init(struct net_device *dev);
-int bcmgenet_mii_connect(struct net_device *dev);
 int bcmgenet_mii_config(struct net_device *dev, bool init);
+int bcmgenet_mii_probe(struct net_device *dev);
 void bcmgenet_mii_exit(struct net_device *dev);
 void bcmgenet_phy_power_set(struct net_device *dev, bool enable);
 void bcmgenet_mii_setup(struct net_device *dev);

drivers/net/ethernet/broadcom/genet/bcmmii.c

@@ -173,46 +173,6 @@ static void bcmgenet_moca_phy_setup(struct bcmgenet_priv *priv)
 					  bcmgenet_fixed_phy_link_update);
 }
 
-int bcmgenet_mii_connect(struct net_device *dev)
-{
-	struct bcmgenet_priv *priv = netdev_priv(dev);
-	struct device_node *dn = priv->pdev->dev.of_node;
-	struct phy_device *phydev;
-	u32 phy_flags = 0;
-	int ret;
-
-	/* Communicate the integrated PHY revision */
-	if (priv->internal_phy)
-		phy_flags = priv->gphy_rev;
-
-	/* Initialize link state variables that bcmgenet_mii_setup() uses */
-	priv->old_link = -1;
-	priv->old_speed = -1;
-	priv->old_duplex = -1;
-	priv->old_pause = -1;
-
-	if (dn) {
-		phydev = of_phy_connect(dev, priv->phy_dn, bcmgenet_mii_setup,
-					phy_flags, priv->phy_interface);
-		if (!phydev) {
-			pr_err("could not attach to PHY\n");
-			return -ENODEV;
-		}
-	} else {
-		phydev = dev->phydev;
-		phydev->dev_flags = phy_flags;
-
-		ret = phy_connect_direct(dev, phydev, bcmgenet_mii_setup,
-					 priv->phy_interface);
-		if (ret) {
-			pr_err("could not attach to PHY\n");
-			return -ENODEV;
-		}
-	}
-
-	return 0;
-}
-
 int bcmgenet_mii_config(struct net_device *dev, bool init)
 {
 	struct bcmgenet_priv *priv = netdev_priv(dev);
@@ -339,21 +299,71 @@ int bcmgenet_mii_config(struct net_device *dev, bool init)
 		bcmgenet_ext_writel(priv, reg, EXT_RGMII_OOB_CTRL);
 	}
 
-	if (init) {
-		linkmode_copy(phydev->advertising, phydev->supported);
+	if (init)
+		dev_info(kdev, "configuring instance for %s\n", phy_name);
 
-		/* The internal PHY has its link interrupts routed to the
-		 * Ethernet MAC ISRs. On GENETv5 there is a hardware issue
-		 * that prevents the signaling of link UP interrupts when
-		 * the link operates at 10Mbps, so fallback to polling for
-		 * those versions of GENET.
-		 */
-		if (priv->internal_phy && !GENET_IS_V5(priv))
-			phydev->irq = PHY_IGNORE_INTERRUPT;
+	return 0;
+}
 
-		dev_info(kdev, "configuring instance for %s\n", phy_name);
+int bcmgenet_mii_probe(struct net_device *dev)
+{
+	struct bcmgenet_priv *priv = netdev_priv(dev);
+	struct device_node *dn = priv->pdev->dev.of_node;
+	struct phy_device *phydev;
+	u32 phy_flags = 0;
+	int ret;
+
+	/* Communicate the integrated PHY revision */
+	if (priv->internal_phy)
+		phy_flags = priv->gphy_rev;
+
+	/* Initialize link state variables that bcmgenet_mii_setup() uses */
+	priv->old_link = -1;
+	priv->old_speed = -1;
+	priv->old_duplex = -1;
+	priv->old_pause = -1;
+
+	if (dn) {
+		phydev = of_phy_connect(dev, priv->phy_dn, bcmgenet_mii_setup,
+					phy_flags, priv->phy_interface);
+		if (!phydev) {
+			pr_err("could not attach to PHY\n");
+			return -ENODEV;
+		}
+	} else {
+		phydev = dev->phydev;
+		phydev->dev_flags = phy_flags;
+
+		ret = phy_connect_direct(dev, phydev, bcmgenet_mii_setup,
+					 priv->phy_interface);
+		if (ret) {
+			pr_err("could not attach to PHY\n");
+			return -ENODEV;
+		}
+	}
+
+	/* Configure port multiplexer based on what the probed PHY device since
+	 * reading the 'max-speed' property determines the maximum supported
+	 * PHY speed which is needed for bcmgenet_mii_config() to configure
+	 * things appropriately.
+	 */
+	ret = bcmgenet_mii_config(dev, true);
+	if (ret) {
+		phy_disconnect(dev->phydev);
+		return ret;
 	}
 
+	linkmode_copy(phydev->advertising, phydev->supported);
+
+	/* The internal PHY has its link interrupts routed to the
+	 * Ethernet MAC ISRs. On GENETv5 there is a hardware issue
+	 * that prevents the signaling of link UP interrupts when
+	 * the link operates at 10Mbps, so fallback to polling for
+	 * those versions of GENET.
+	 */
+	if (priv->internal_phy && !GENET_IS_V5(priv))
+		dev->phydev->irq = PHY_IGNORE_INTERRUPT;
+
 	return 0;
 }