Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Board-level changes

This adds and extends support for specific boards on a number of
ARM platforms:  omap, imx, samsung, tegra, ...

* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (49 commits)
  Enable 32 bit flash support for iMX21ADS board
  ARM: mx31pdk: Add MC13783 RTC support
  iomux-mx25: configuration to support CSPI3 on CSI pins
  MX1:apf9328: Add i2c support
  mioa701: add newly available DoC G3 chip
  arm/tegra: remove __initdata annotation from pinmux tables
  arm/tegra: Use bus notifiers to trigger pinmux setup
  arm/tegra: Refactor board-*-pinmux.c to share code
  arm/tegra: Fix mistake in Trimslice's pinmux
  arm/tegra: Rework Seaboard-vs-Ventana pinmux table
  arm/tegra: Remove useless entries from ventana_pinmux[]
  arm/tegra: PCIe: Remove include of mach/pinmux.h
  arm/tegra: Harmony PCIe: Don't touch pinmux
  arm/tegra: Add AUXDATA for tegra-pinmux and tegra-gpio
  arm/tegra: Split Seaboard GPIO table to allow for Ventana
  ARM: imx6q: generate imx6q dtb files
  arm/imx6q: Rename Sabreauto to Armadillo2
  arm/imx6q-sabrelite: add enet phy ksz9021rn fixup
  arm/imx6: add imx6q sabrelite board support
  dts/imx: rename uart labels to consistent with hw spec
  ...

Documentation/devicetree/bindings/arm/fsl.txt

@@ -21,6 +21,10 @@ i.MX53 Smart Mobile Reference Design Board
 Required root node properties:
     - compatible = "fsl,imx53-smd", "fsl,imx53";
 
-i.MX6 Quad SABRE Automotive Board
+i.MX6 Quad Armadillo2 Board
 Required root node properties:
-    - compatible = "fsl,imx6q-sabreauto", "fsl,imx6q";
+    - compatible = "fsl,imx6q-arm2", "fsl,imx6q";
+
+i.MX6 Quad SABRE Lite Board
+Required root node properties:
+    - compatible = "fsl,imx6q-sabrelite", "fsl,imx6q";

arch/arm/boot/dts/imx51-babbage.dts

@@ -35,20 +35,19 @@ esdhc@70004000 { /* ESDHC1 */
 				};
 
 				esdhc@70008000 { /* ESDHC2 */
-					cd-gpios = <&gpio0 6 0>; /* GPIO1_6 */
-					wp-gpios = <&gpio0 5 0>; /* GPIO1_5 */
+					cd-gpios = <&gpio1 6 0>;
+					wp-gpios = <&gpio1 5 0>;
 					status = "okay";
 				};
 
-				uart2: uart@7000c000 { /* UART3 */
+				uart3: uart@7000c000 {
 					fsl,uart-has-rtscts;
 					status = "okay";
 				};
 
 				ecspi@70010000 { /* ECSPI1 */
 					fsl,spi-num-chipselects = <2>;
-					cs-gpios = <&gpio3 24 0>, /* GPIO4_24 */
-						   <&gpio3 25 0>; /* GPIO4_25 */
+					cs-gpios = <&gpio4 24 0>, <&gpio4 25 0>;
 					status = "okay";
 
 					pmic: mc13892@0 {
@@ -57,7 +56,7 @@ pmic: mc13892@0 {
 						compatible = "fsl,mc13892";
 						spi-max-frequency = <6000000>;
 						reg = <0>;
-						mc13xxx-irq-gpios = <&gpio0 8 0>; /* GPIO1_8 */
+						mc13xxx-irq-gpios = <&gpio1 8 0>;
 						fsl,mc13xxx-uses-regulator;
 					};
 
@@ -91,12 +90,12 @@ iomuxc@73fa8000 {
 				reg = <0x73fa8000 0x4000>;
 			};
 
-			uart0: uart@73fbc000 {
+			uart1: uart@73fbc000 {
 				fsl,uart-has-rtscts;
 				status = "okay";
 			};
 
-			uart1: uart@73fc0000 {
+			uart2: uart@73fc0000 {
 				status = "okay";
 			};
 		};
@@ -127,7 +126,7 @@ gpio-keys {
 
 		power {
 			label = "Power Button";
-			gpios = <&gpio1 21 0>;
+			gpios = <&gpio2 21 0>;
 			linux,code = <116>; /* KEY_POWER */
 			gpio-key,wakeup;
 		};

arch/arm/boot/dts/imx51.dtsi

@@ -14,9 +14,9 @@
 
 / {
 	aliases {
-		serial0 = &uart0;
-		serial1 = &uart1;
-		serial2 = &uart2;
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
 	};
 
 	tzic: tz-interrupt-controller@e0000000 {
@@ -86,7 +86,7 @@ esdhc@70008000 { /* ESDHC2 */
 					status = "disabled";
 				};
 
-				uart2: uart@7000c000 { /* UART3 */
+				uart3: uart@7000c000 {
 					compatible = "fsl,imx51-uart", "fsl,imx21-uart";
 					reg = <0x7000c000 0x4000>;
 					interrupts = <33>;
@@ -117,7 +117,7 @@ esdhc@70024000 { /* ESDHC4 */
 				};
 			};
 
-			gpio0: gpio@73f84000 { /* GPIO1 */
+			gpio1: gpio@73f84000 {
 				compatible = "fsl,imx51-gpio", "fsl,imx31-gpio";
 				reg = <0x73f84000 0x4000>;
 				interrupts = <50 51>;
@@ -127,7 +127,7 @@ gpio0: gpio@73f84000 { /* GPIO1 */
 				#interrupt-cells = <1>;
 			};
 
-			gpio1: gpio@73f88000 { /* GPIO2 */
+			gpio2: gpio@73f88000 {
 				compatible = "fsl,imx51-gpio", "fsl,imx31-gpio";
 				reg = <0x73f88000 0x4000>;
 				interrupts = <52 53>;
@@ -137,7 +137,7 @@ gpio1: gpio@73f88000 { /* GPIO2 */
 				#interrupt-cells = <1>;
 			};
 
-			gpio2: gpio@73f8c000 { /* GPIO3 */
+			gpio3: gpio@73f8c000 {
 				compatible = "fsl,imx51-gpio", "fsl,imx31-gpio";
 				reg = <0x73f8c000 0x4000>;
 				interrupts = <54 55>;
@@ -147,7 +147,7 @@ gpio2: gpio@73f8c000 { /* GPIO3 */
 				#interrupt-cells = <1>;
 			};
 
-			gpio3: gpio@73f90000 { /* GPIO4 */
+			gpio4: gpio@73f90000 {
 				compatible = "fsl,imx51-gpio", "fsl,imx31-gpio";
 				reg = <0x73f90000 0x4000>;
 				interrupts = <56 57>;
@@ -171,14 +171,14 @@ wdog@73f9c000 { /* WDOG2 */
 				status = "disabled";
 			};
 
-			uart0: uart@73fbc000 {
+			uart1: uart@73fbc000 {
 				compatible = "fsl,imx51-uart", "fsl,imx21-uart";
 				reg = <0x73fbc000 0x4000>;
 				interrupts = <31>;
 				status = "disabled";
 			};
 
-			uart1: uart@73fc0000 {
+			uart2: uart@73fc0000 {
 				compatible = "fsl,imx51-uart", "fsl,imx21-uart";
 				reg = <0x73fc0000 0x4000>;
 				interrupts = <32>;

arch/arm/boot/dts/imx53-ard.dts

@@ -29,8 +29,8 @@ soc {
 		aips@50000000 { /* AIPS1 */
 			spba@50000000 {
 				esdhc@50004000 { /* ESDHC1 */
-					cd-gpios = <&gpio0 1 0>; /* GPIO1_1 */
-					wp-gpios = <&gpio0 9 0>; /* GPIO1_9 */
+					cd-gpios = <&gpio1 1 0>;
+					wp-gpios = <&gpio1 9 0>;
 					status = "okay";
 				};
 			};
@@ -44,7 +44,7 @@ iomuxc@53fa8000 {
 				reg = <0x53fa8000 0x4000>;
 			};
 
-			uart0: uart@53fbc000 { /* UART1 */
+			uart1: uart@53fbc000 {
 				status = "okay";
 			};
 		};
@@ -67,7 +67,7 @@ lan9220@f4000000 {
 			compatible = "smsc,lan9220", "smsc,lan9115";
 			reg = <0xf4000000 0x2000000>;
 			phy-mode = "mii";
-			interrupt-parent = <&gpio1>;
+			interrupt-parent = <&gpio2>;
 			interrupts = <31>;
 			reg-io-width = <4>;
 			smsc,irq-push-pull;
@@ -79,34 +79,34 @@ gpio-keys {
 
 		home {
 			label = "Home";
-			gpios = <&gpio4 10 0>; /* GPIO5_10 */
+			gpios = <&gpio5 10 0>;
 			linux,code = <102>; /* KEY_HOME */
 			gpio-key,wakeup;
 		};
 
 		back {
 			label = "Back";
-			gpios = <&gpio4 11 0>; /* GPIO5_11 */
+			gpios = <&gpio5 11 0>;
 			linux,code = <158>; /* KEY_BACK */
 			gpio-key,wakeup;
 		};
 
 		program {
 			label = "Program";
-			gpios = <&gpio4 12 0>; /* GPIO5_12 */
+			gpios = <&gpio5 12 0>;
 			linux,code = <362>; /* KEY_PROGRAM */
 			gpio-key,wakeup;
 		};
 
 		volume-up {
 			label = "Volume Up";
-			gpios = <&gpio4 13 0>; /* GPIO5_13 */
+			gpios = <&gpio5 13 0>;
 			linux,code = <115>; /* KEY_VOLUMEUP */
 		};
 
 		volume-down {
 			label = "Volume Down";
-			gpios = <&gpio3 0 0>; /* GPIO4_0 */
+			gpios = <&gpio4 0 0>;
 			linux,code = <114>; /* KEY_VOLUMEDOWN */
 		};
 	};

arch/arm/boot/dts/imx53-evk.dts

@@ -29,15 +29,14 @@ soc {
 		aips@50000000 { /* AIPS1 */
 			spba@50000000 {
 				esdhc@50004000 { /* ESDHC1 */
-					cd-gpios = <&gpio2 13 0>; /* GPIO3_13 */
-					wp-gpios = <&gpio2 14 0>; /* GPIO3_14 */
+					cd-gpios = <&gpio3 13 0>;
+					wp-gpios = <&gpio3 14 0>;
 					status = "okay";
 				};
 
 				ecspi@50010000 { /* ECSPI1 */
 					fsl,spi-num-chipselects = <2>;
-					cs-gpios = <&gpio1 30 0>, /* GPIO2_30 */
-						   <&gpio2 19 0>; /* GPIO3_19 */
+					cs-gpios = <&gpio2 30 0>, <&gpio3 19 0>;
 					status = "okay";
 
 					flash: at45db321d@1 {
@@ -61,8 +60,8 @@ partition@40000 {
 				};
 
 				esdhc@50020000 { /* ESDHC3 */
-					cd-gpios = <&gpio2 11 0>; /* GPIO3_11 */
-					wp-gpios = <&gpio2 12 0>; /* GPIO3_12 */
+					cd-gpios = <&gpio3 11 0>;
+					wp-gpios = <&gpio3 12 0>;
 					status = "okay";
 				};
 			};
@@ -76,7 +75,7 @@ iomuxc@53fa8000 {
 				reg = <0x53fa8000 0x4000>;
 			};
 
-			uart0: uart@53fbc000 { /* UART1 */
+			uart1: uart@53fbc000 {
 				status = "okay";
 			};
 		};
@@ -102,7 +101,7 @@ codec: sgtl5000@0a {
 
 			fec@63fec000 {
 				phy-mode = "rmii";
-				phy-reset-gpios = <&gpio6 6 0>; /* GPIO7_6 */
+				phy-reset-gpios = <&gpio7 6 0>;
 				status = "okay";
 			};
 		};
@@ -113,7 +112,7 @@ leds {
 
 		green {
 			label = "Heartbeat";
-			gpios = <&gpio6 7 0>; /* GPIO7_7 */
+			gpios = <&gpio7 7 0>;
 			linux,default-trigger = "heartbeat";
 		};
 	};

arch/arm/boot/dts/imx53-qsb.dts

@@ -29,13 +29,13 @@ soc {
 		aips@50000000 { /* AIPS1 */
 			spba@50000000 {
 				esdhc@50004000 { /* ESDHC1 */
-					cd-gpios = <&gpio2 13 0>; /* GPIO3_13 */
+					cd-gpios = <&gpio3 13 0>;
 					status = "okay";
 				};
 
 				esdhc@50020000 { /* ESDHC3 */
-					cd-gpios = <&gpio2 11 0>; /* GPIO3_11 */
-					wp-gpios = <&gpio2 12 0>; /* GPIO3_12 */
+					cd-gpios = <&gpio3 11 0>;
+					wp-gpios = <&gpio3 12 0>;
 					status = "okay";
 				};
 			};
@@ -49,7 +49,7 @@ iomuxc@53fa8000 {
 				reg = <0x53fa8000 0x4000>;
 			};
 
-			uart0: uart@53fbc000 { /* UART1 */
+			uart1: uart@53fbc000 {
 				status = "okay";
 			};
 		};
@@ -84,7 +84,7 @@ pmic: dialog@48 {
 
 			fec@63fec000 {
 				phy-mode = "rmii";
-				phy-reset-gpios = <&gpio6 6 0>; /* GPIO7_6 */
+				phy-reset-gpios = <&gpio7 6 0>;
 				status = "okay";
 			};
 		};
@@ -95,20 +95,20 @@ gpio-keys {
 
 		power {
 			label = "Power Button";
-			gpios = <&gpio0 8 0>; /* GPIO1_8 */
+			gpios = <&gpio1 8 0>;
 			linux,code = <116>; /* KEY_POWER */
 			gpio-key,wakeup;
 		};
 
 		volume-up {
 			label = "Volume Up";
-			gpios = <&gpio1 14 0>; /* GPIO2_14 */
+			gpios = <&gpio2 14 0>;
 			linux,code = <115>; /* KEY_VOLUMEUP */
 		};
 
 		volume-down {
 			label = "Volume Down";
-			gpios = <&gpio1 15 0>; /* GPIO2_15 */
+			gpios = <&gpio2 15 0>;
 			linux,code = <114>; /* KEY_VOLUMEDOWN */
 		};
 	};
@@ -118,7 +118,7 @@ leds {
 
 		user {
 			label = "Heartbeat";
-			gpios = <&gpio6 7 0>; /* GPIO7_7 */
+			gpios = <&gpio7 7 0>;
 			linux,default-trigger = "heartbeat";
 		};
 	};

arch/arm/boot/dts/imx53-smd.dts

@@ -29,8 +29,8 @@ soc {
 		aips@50000000 { /* AIPS1 */
 			spba@50000000 {
 				esdhc@50004000 { /* ESDHC1 */
-					cd-gpios = <&gpio2 13 0>; /* GPIO3_13 */
-					wp-gpios = <&gpio3 11 0>; /* GPIO4_11 */
+					cd-gpios = <&gpio3 13 0>;
+					wp-gpios = <&gpio4 11 0>;
 					status = "okay";
 				};
 
@@ -39,15 +39,14 @@ esdhc@50008000 { /* ESDHC2 */
 					status = "okay";
 				};
 
-				uart2: uart@5000c000 { /* UART3 */
+				uart3: uart@5000c000 {
 					fsl,uart-has-rtscts;
 					status = "okay";
 				};
 
 				ecspi@50010000 { /* ECSPI1 */
 					fsl,spi-num-chipselects = <2>;
-					cs-gpios = <&gpio1 30 0>, /* GPIO2_30 */
-						   <&gpio2 19 0>; /* GPIO3_19 */
+					cs-gpios = <&gpio2 30 0>, <&gpio3 19 0>;
 					status = "okay";
 
 					zigbee: mc1323@0 {
@@ -91,11 +90,11 @@ iomuxc@53fa8000 {
 				reg = <0x53fa8000 0x4000>;
 			};
 
-			uart0: uart@53fbc000 { /* UART1 */
+			uart1: uart@53fbc000 {
 				status = "okay";
 			};
 
-			uart1: uart@53fc0000 { /* UART2 */
+			uart2: uart@53fc0000 {
 				status = "okay";
 			};
 		};
@@ -145,7 +144,7 @@ pmic: dialog@48 {
 
 			fec@63fec000 {
 				phy-mode = "rmii";
-				phy-reset-gpios = <&gpio6 6 0>; /* GPIO7_6 */
+				phy-reset-gpios = <&gpio7 6 0>;
 				status = "okay";
 			};
 		};
@@ -156,13 +155,13 @@ gpio-keys {
 
 		volume-up {
 			label = "Volume Up";
-			gpios = <&gpio1 14 0>; /* GPIO2_14 */
+			gpios = <&gpio2 14 0>;
 			linux,code = <115>; /* KEY_VOLUMEUP */
 		};
 
 		volume-down {
 			label = "Volume Down";
-			gpios = <&gpio1 15 0>; /* GPIO2_15 */
+			gpios = <&gpio2 15 0>;
 			linux,code = <114>; /* KEY_VOLUMEDOWN */
 		};
 	};

arch/arm/boot/dts/imx53.dtsi

@@ -14,11 +14,11 @@
 
 / {
 	aliases {
-		serial0 = &uart0;
-		serial1 = &uart1;
-		serial2 = &uart2;
-		serial3 = &uart3;
-		serial4 = &uart4;
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
+		serial3 = &uart4;
+		serial4 = &uart5;
 	};
 
 	tzic: tz-interrupt-controller@0fffc000 {
@@ -88,7 +88,7 @@ esdhc@50008000 { /* ESDHC2 */
 					status = "disabled";
 				};
 
-				uart2: uart@5000c000 { /* UART3 */
+				uart3: uart@5000c000 {
 					compatible = "fsl,imx53-uart", "fsl,imx21-uart";
 					reg = <0x5000c000 0x4000>;
 					interrupts = <33>;
@@ -119,7 +119,7 @@ esdhc@50024000 { /* ESDHC4 */
 				};
 			};
 
-			gpio0: gpio@53f84000 { /* GPIO1 */
+			gpio1: gpio@53f84000 {
 				compatible = "fsl,imx53-gpio", "fsl,imx31-gpio";
 				reg = <0x53f84000 0x4000>;
 				interrupts = <50 51>;
@@ -129,7 +129,7 @@ gpio0: gpio@53f84000 { /* GPIO1 */
 				#interrupt-cells = <1>;
 			};
 
-			gpio1: gpio@53f88000 { /* GPIO2 */
+			gpio2: gpio@53f88000 {
 				compatible = "fsl,imx53-gpio", "fsl,imx31-gpio";
 				reg = <0x53f88000 0x4000>;
 				interrupts = <52 53>;
@@ -139,7 +139,7 @@ gpio1: gpio@53f88000 { /* GPIO2 */
 				#interrupt-cells = <1>;
 			};
 
-			gpio2: gpio@53f8c000 { /* GPIO3 */
+			gpio3: gpio@53f8c000 {
 				compatible = "fsl,imx53-gpio", "fsl,imx31-gpio";
 				reg = <0x53f8c000 0x4000>;
 				interrupts = <54 55>;
@@ -149,7 +149,7 @@ gpio2: gpio@53f8c000 { /* GPIO3 */
 				#interrupt-cells = <1>;
 			};
 
-			gpio3: gpio@53f90000 { /* GPIO4 */
+			gpio4: gpio@53f90000 {
 				compatible = "fsl,imx53-gpio", "fsl,imx31-gpio";
 				reg = <0x53f90000 0x4000>;
 				interrupts = <56 57>;
@@ -173,21 +173,21 @@ wdog@53f9c000 { /* WDOG2 */
 				status = "disabled";
 			};
 
-			uart0: uart@53fbc000 { /* UART1 */
+			uart1: uart@53fbc000 {
 				compatible = "fsl,imx53-uart", "fsl,imx21-uart";
 				reg = <0x53fbc000 0x4000>;
 				interrupts = <31>;
 				status = "disabled";
 			};
 
-			uart1: uart@53fc0000 { /* UART2 */
+			uart2: uart@53fc0000 {
 				compatible = "fsl,imx53-uart", "fsl,imx21-uart";
 				reg = <0x53fc0000 0x4000>;
 				interrupts = <32>;
 				status = "disabled";
 			};
 
-			gpio4: gpio@53fdc000 { /* GPIO5 */
+			gpio5: gpio@53fdc000 {
 				compatible = "fsl,imx53-gpio", "fsl,imx31-gpio";
 				reg = <0x53fdc000 0x4000>;
 				interrupts = <103 104>;
@@ -197,7 +197,7 @@ gpio4: gpio@53fdc000 { /* GPIO5 */
 				#interrupt-cells = <1>;
 			};
 
-			gpio5: gpio@53fe0000 { /* GPIO6 */
+			gpio6: gpio@53fe0000 {
 				compatible = "fsl,imx53-gpio", "fsl,imx31-gpio";
 				reg = <0x53fe0000 0x4000>;
 				interrupts = <105 106>;
@@ -207,7 +207,7 @@ gpio5: gpio@53fe0000 { /* GPIO6 */
 				#interrupt-cells = <1>;
 			};
 
-			gpio6: gpio@53fe4000 { /* GPIO7 */
+			gpio7: gpio@53fe4000 {
 				compatible = "fsl,imx53-gpio", "fsl,imx31-gpio";
 				reg = <0x53fe4000 0x4000>;
 				interrupts = <107 108>;
@@ -226,7 +226,7 @@ i2c@53fec000 { /* I2C3 */
 				status = "disabled";
 			};
 
-			uart3: uart@53ff0000 { /* UART4 */
+			uart4: uart@53ff0000 {
 				compatible = "fsl,imx53-uart", "fsl,imx21-uart";
 				reg = <0x53ff0000 0x4000>;
 				interrupts = <13>;
@@ -241,7 +241,7 @@ aips@60000000 {	/* AIPS2 */
 			reg = <0x60000000 0x10000000>;
 			ranges;
 
-			uart4: uart@63f90000 { /* UART5 */
+			uart5: uart@63f90000 {
 				compatible = "fsl,imx53-uart", "fsl,imx21-uart";
 				reg = <0x63f90000 0x4000>;
 				interrupts = <86>;

arch/arm/boot/dts/imx6q-sabreauto.dts → arch/arm/boot/dts/imx6q-arm2.dts

@@ -14,8 +14,8 @@
 /include/ "imx6q.dtsi"
 
 / {
-	model = "Freescale i.MX6 Quad SABRE Automotive Board";
-	compatible = "fsl,imx6q-sabreauto", "fsl,imx6q";
+	model = "Freescale i.MX6 Quad Armadillo2 Board";
+	compatible = "fsl,imx6q-arm2", "fsl,imx6q";
 
 	chosen {
 		bootargs = "console=ttymxc0,115200 root=/dev/mmcblk3p3 rootwait";
@@ -34,8 +34,8 @@ enet@02188000 {
 			};
 
 			usdhc@02198000 { /* uSDHC3 */
-				cd-gpios = <&gpio5 11 0>; /* GPIO6_11 */
-				wp-gpios = <&gpio5 14 0>; /* GPIO6_14 */
+				cd-gpios = <&gpio6 11 0>;
+				wp-gpios = <&gpio6 14 0>;
 				status = "okay";
 			};
 
@@ -44,7 +44,7 @@ usdhc@0219c000 { /* uSDHC4 */
 				status = "okay";
 			};
 
-			uart3: uart@021f0000 { /* UART4 */
+			uart4: uart@021f0000 {
 				status = "okay";
 			};
 		};
@@ -55,7 +55,7 @@ leds {
 
 		debug-led {
 			label = "Heartbeat";
-			gpios = <&gpio2 25 0>; /* GPIO3_25 */
+			gpios = <&gpio3 25 0>;
 			linux,default-trigger = "heartbeat";
 		};
 	};

arch/arm/boot/dts/imx6q-sabrelite.dts

+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "imx6q.dtsi"
+
+/ {
+	model = "Freescale i.MX6 Quad SABRE Lite Board";
+	compatible = "fsl,imx6q-sabrelite", "fsl,imx6q";
+
+	memory {
+		reg = <0x10000000 0x40000000>;
+	};
+
+	soc {
+		aips-bus@02100000 { /* AIPS2 */
+			enet@02188000 {
+				phy-mode = "rgmii";
+				phy-reset-gpios = <&gpio3 23 0>;
+				status = "okay";
+			};
+
+			usdhc@02198000 { /* uSDHC3 */
+				cd-gpios = <&gpio7 0 0>;
+				wp-gpios = <&gpio7 1 0>;
+				status = "okay";
+			};
+
+			usdhc@0219c000 { /* uSDHC4 */
+				cd-gpios = <&gpio2 6 0>;
+				wp-gpios = <&gpio2 7 0>;
+				status = "okay";
+			};
+
+			uart2: uart@021e8000 {
+				status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/imx6q.dtsi

@@ -14,11 +14,11 @@
 
 / {
 	aliases {
-		serial0 = &uart0;
-		serial1 = &uart1;
-		serial2 = &uart2;
-		serial3 = &uart3;
-		serial4 = &uart4;
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
+		serial3 = &uart4;
+		serial4 = &uart5;
 	};
 
 	cpus {
@@ -165,7 +165,7 @@ ecspi@02018000 { /* eCSPI5 */
 					status = "disabled";
 				};
 
-				uart0: uart@02020000 { /* UART1 */
+				uart1: uart@02020000 {
 					compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02020000 0x4000>;
 					interrupts = <0 26 0x04>;
@@ -247,7 +247,7 @@ gpt@02098000 {
 				interrupts = <0 55 0x04>;
 			};
 
-			gpio0: gpio@0209c000 { /* GPIO1 */
+			gpio1: gpio@0209c000 {
 				compatible = "fsl,imx6q-gpio", "fsl,imx31-gpio";
 				reg = <0x0209c000 0x4000>;
 				interrupts = <0 66 0x04 0 67 0x04>;
@@ -257,7 +257,7 @@ gpio0: gpio@0209c000 { /* GPIO1 */
 				#interrupt-cells = <1>;
 			};
 
-			gpio1: gpio@020a0000 { /* GPIO2 */
+			gpio2: gpio@020a0000 {
 				compatible = "fsl,imx6q-gpio", "fsl,imx31-gpio";
 				reg = <0x020a0000 0x4000>;
 				interrupts = <0 68 0x04 0 69 0x04>;
@@ -267,7 +267,7 @@ gpio1: gpio@020a0000 { /* GPIO2 */
 				#interrupt-cells = <1>;
 			};
 
-			gpio2: gpio@020a4000 { /* GPIO3 */
+			gpio3: gpio@020a4000 {
 				compatible = "fsl,imx6q-gpio", "fsl,imx31-gpio";
 				reg = <0x020a4000 0x4000>;
 				interrupts = <0 70 0x04 0 71 0x04>;
@@ -277,7 +277,7 @@ gpio2: gpio@020a4000 { /* GPIO3 */
 				#interrupt-cells = <1>;
 			};
 
-			gpio3: gpio@020a8000 { /* GPIO4 */
+			gpio4: gpio@020a8000 {
 				compatible = "fsl,imx6q-gpio", "fsl,imx31-gpio";
 				reg = <0x020a8000 0x4000>;
 				interrupts = <0 72 0x04 0 73 0x04>;
@@ -287,7 +287,7 @@ gpio3: gpio@020a8000 { /* GPIO4 */
 				#interrupt-cells = <1>;
 			};
 
-			gpio4: gpio@020ac000 { /* GPIO5 */
+			gpio5: gpio@020ac000 {
 				compatible = "fsl,imx6q-gpio", "fsl,imx31-gpio";
 				reg = <0x020ac000 0x4000>;
 				interrupts = <0 74 0x04 0 75 0x04>;
@@ -297,7 +297,7 @@ gpio4: gpio@020ac000 { /* GPIO5 */
 				#interrupt-cells = <1>;
 			};
 
-			gpio5: gpio@020b0000 { /* GPIO6 */
+			gpio6: gpio@020b0000 {
 				compatible = "fsl,imx6q-gpio", "fsl,imx31-gpio";
 				reg = <0x020b0000 0x4000>;
 				interrupts = <0 76 0x04 0 77 0x04>;
@@ -307,7 +307,7 @@ gpio5: gpio@020b0000 { /* GPIO6 */
 				#interrupt-cells = <1>;
 			};
 
-			gpio6: gpio@020b4000 { /* GPIO7 */
+			gpio7: gpio@020b4000 {
 				compatible = "fsl,imx6q-gpio", "fsl,imx31-gpio";
 				reg = <0x020b4000 0x4000>;
 				interrupts = <0 78 0x04 0 79 0x04>;
@@ -543,28 +543,28 @@ vdoa@021e4000 {
 				interrupts = <0 18 0x04>;
 			};
 
-			uart1: uart@021e8000 { /* UART2 */
+			uart2: uart@021e8000 {
 				compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
 				reg = <0x021e8000 0x4000>;
 				interrupts = <0 27 0x04>;
 				status = "disabled";
 			};
 
-			uart2: uart@021ec000 { /* UART3 */
+			uart3: uart@021ec000 {
 				compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
 				reg = <0x021ec000 0x4000>;
 				interrupts = <0 28 0x04>;
 				status = "disabled";
 			};
 
-			uart3: uart@021f0000 { /* UART4 */
+			uart4: uart@021f0000 {
 				compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
 				reg = <0x021f0000 0x4000>;
 				interrupts = <0 29 0x04>;
 				status = "disabled";
 			};
 
-			uart4: uart@021f4000 { /* UART5 */
+			uart5: uart@021f4000 {
 				compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
 				reg = <0x021f4000 0x4000>;
 				interrupts = <0 30 0x04>;

arch/arm/configs/imx_v4_v5_defconfig

@@ -68,7 +68,6 @@ CONFIG_MTD_CFI=y
 CONFIG_MTD_CFI_ADV_OPTIONS=y
 CONFIG_MTD_CFI_GEOMETRY=y
 # CONFIG_MTD_MAP_BANK_WIDTH_1 is not set
-# CONFIG_MTD_MAP_BANK_WIDTH_4 is not set
 # CONFIG_MTD_CFI_I2 is not set
 CONFIG_MTD_CFI_INTELEXT=y
 CONFIG_MTD_PHYSMAP=y

arch/arm/mach-imx/Kconfig

@@ -98,6 +98,7 @@ config MACH_SCB9328
 config MACH_APF9328
 	bool "APF9328"
 	select SOC_IMX1
+	select IMX_HAVE_PLATFORM_IMX_I2C
 	select IMX_HAVE_PLATFORM_IMX_UART
 	help
 	  Say Yes here if you are using the Armadeus APF9328 development board

arch/arm/mach-imx/Makefile.boot

@@ -25,3 +25,6 @@ initrd_phys-$(CONFIG_SOC_IMX35)	:= 0x80800000
 zreladdr-$(CONFIG_SOC_IMX6Q)	+= 0x10008000
 params_phys-$(CONFIG_SOC_IMX6Q)	:= 0x10000100
 initrd_phys-$(CONFIG_SOC_IMX6Q)	:= 0x10800000
+
+dtb-$(CONFIG_SOC_IMX6Q)	+= imx6q-arm2.dtb \
+			   imx6q-sabrelite.dtb

arch/arm/mach-imx/mach-apf9328.c

@@ -18,6 +18,7 @@
 #include <linux/platform_device.h>
 #include <linux/mtd/physmap.h>
 #include <linux/dm9000.h>
+#include <linux/i2c.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -41,6 +42,9 @@ static const int apf9328_pins[] __initconst = {
 	PB29_PF_UART2_RTS,
 	PB30_PF_UART2_TXD,
 	PB31_PF_UART2_RXD,
+	/* I2C */
+	PA15_PF_I2C_SDA,
+	PA16_PF_I2C_SCL,
 };
 
 /*
@@ -103,6 +107,10 @@ static const struct imxuart_platform_data uart1_pdata __initconst = {
 	.flags = IMXUART_HAVE_RTSCTS,
 };
 
+static const struct imxi2c_platform_data apf9328_i2c_data __initconst = {
+	.bitrate = 100000,
+};
+
 static struct platform_device *devices[] __initdata = {
 	&apf9328_flash_device,
 	&dm9000x_device,
@@ -119,6 +127,8 @@ static void __init apf9328_init(void)
 	imx1_add_imx_uart0(NULL);
 	imx1_add_imx_uart1(&uart1_pdata);
 
+	imx1_add_imx_i2c(&apf9328_i2c_data);
+
 	platform_add_devices(devices, ARRAY_SIZE(devices));
 }
 

arch/arm/mach-imx/mach-imx6q.c

@@ -19,6 +19,8 @@
 #include <linux/of_address.h>
 #include <linux/of_irq.h>
 #include <linux/of_platform.h>
+#include <linux/phy.h>
+#include <linux/micrel_phy.h>
 #include <asm/hardware/cache-l2x0.h>
 #include <asm/hardware/gic.h>
 #include <asm/mach/arch.h>
@@ -56,8 +58,27 @@ void imx6q_restart(char mode, const char *cmd)
 	soft_restart(0);
 }
 
+/* For imx6q sabrelite board: set KSZ9021RN RGMII pad skew */
+static int ksz9021rn_phy_fixup(struct phy_device *phydev)
+{
+	/* min rx data delay */
+	phy_write(phydev, 0x0b, 0x8105);
+	phy_write(phydev, 0x0c, 0x0000);
+
+	/* max rx/tx clock delay, min rx/tx control delay */
+	phy_write(phydev, 0x0b, 0x8104);
+	phy_write(phydev, 0x0c, 0xf0f0);
+	phy_write(phydev, 0x0b, 0x104);
+
+	return 0;
+}
+
 static void __init imx6q_init_machine(void)
 {
+	if (of_machine_is_compatible("fsl,imx6q-sabrelite"))
+		phy_register_fixup_for_uid(PHY_ID_KSZ9021, MICREL_PHY_ID_MASK,
+					   ksz9021rn_phy_fixup);
+
 	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
 
 	imx6q_pm_init();
@@ -105,7 +126,8 @@ static struct sys_timer imx6q_timer = {
 };
 
 static const char *imx6q_dt_compat[] __initdata = {
-	"fsl,imx6q-sabreauto",
+	"fsl,imx6q-arm2",
+	"fsl,imx6q-sabrelite",
 	NULL,
 };
 

arch/arm/mach-imx/mach-mx31_3ds.c

@@ -492,7 +492,7 @@ static struct mc13xxx_platform_data mc13783_pdata = {
 		.regulators = mx31_3ds_regulators,
 		.num_regulators = ARRAY_SIZE(mx31_3ds_regulators),
 	},
-	.flags  = MC13XXX_USE_TOUCHSCREEN,
+	.flags  = MC13XXX_USE_TOUCHSCREEN | MC13XXX_USE_RTC,
 };
 
 /* SPI */

arch/arm/mach-omap2/Kconfig

@@ -324,6 +324,11 @@ config MACH_TI8168EVM
 	depends on SOC_OMAPTI81XX
 	default y
 
+config MACH_TI8148EVM
+	bool "TI8148 Evaluation Module"
+	depends on SOC_OMAPTI81XX
+	default y
+
 config MACH_OMAP_4430SDP
 	bool "OMAP 4430 SDP board"
 	default y

arch/arm/mach-omap2/Makefile

@@ -232,6 +232,7 @@ obj-$(CONFIG_MACH_CRANEBOARD)		+= board-am3517crane.o
 
 obj-$(CONFIG_MACH_SBC3530)		+= board-omap3stalker.o
 obj-$(CONFIG_MACH_TI8168EVM)		+= board-ti8168evm.o
+obj-$(CONFIG_MACH_TI8148EVM)		+= board-ti8168evm.o
 
 # Platform specific device init code
 

arch/arm/mach-omap2/board-4430sdp.c

@@ -372,11 +372,17 @@ static struct platform_device sdp4430_vbat = {
 	},
 };
 
+static struct platform_device sdp4430_dmic_codec = {
+	.name	= "dmic-codec",
+	.id	= -1,
+};
+
 static struct platform_device *sdp4430_devices[] __initdata = {
 	&sdp4430_gpio_keys_device,
 	&sdp4430_leds_gpio,
 	&sdp4430_leds_pwm,
 	&sdp4430_vbat,
+	&sdp4430_dmic_codec,
 };
 
 static struct omap_musb_board_data musb_board_data = {

arch/arm/mach-omap2/board-cm-t35.c

@@ -53,7 +53,8 @@
 #include "hsmmc.h"
 #include "common-board-devices.h"
 
-#define CM_T35_GPIO_PENDOWN	57
+#define CM_T35_GPIO_PENDOWN		57
+#define SB_T35_USB_HUB_RESET_GPIO	167
 
 #define CM_T35_SMSC911X_CS	5
 #define CM_T35_SMSC911X_GPIO	163
@@ -339,8 +340,10 @@ static struct regulator_consumer_supply cm_t35_vsim_supply[] = {
 	REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
 };
 
-static struct regulator_consumer_supply cm_t35_vdvi_supply[] = {
-	REGULATOR_SUPPLY("vdvi", "omapdss"),
+static struct regulator_consumer_supply cm_t35_vio_supplies[] = {
+	REGULATOR_SUPPLY("vcc", "spi1.0"),
+	REGULATOR_SUPPLY("vdds_dsi", "omapdss"),
+	REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi1"),
 };
 
 /* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
@@ -373,6 +376,19 @@ static struct regulator_init_data cm_t35_vsim = {
 	.consumer_supplies	= cm_t35_vsim_supply,
 };
 
+static struct regulator_init_data cm_t35_vio = {
+	.constraints = {
+		.min_uV			= 1800000,
+		.max_uV			= 1800000,
+		.apply_uV		= true,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_MODE,
+	},
+	.num_consumer_supplies	= ARRAY_SIZE(cm_t35_vio_supplies),
+	.consumer_supplies	= cm_t35_vio_supplies,
+};
+
 static uint32_t cm_t35_keymap[] = {
 	KEY(0, 0, KEY_A),	KEY(0, 1, KEY_B),	KEY(0, 2, KEY_LEFT),
 	KEY(1, 0, KEY_UP),	KEY(1, 1, KEY_ENTER),	KEY(1, 2, KEY_DOWN),
@@ -421,6 +437,23 @@ static struct usbhs_omap_board_data usbhs_bdata __initdata = {
 	.reset_gpio_port[2]  = -EINVAL
 };
 
+static void cm_t35_init_usbh(void)
+{
+	int err;
+
+	err = gpio_request_one(SB_T35_USB_HUB_RESET_GPIO,
+			       GPIOF_OUT_INIT_LOW, "usb hub rst");
+	if (err) {
+		pr_err("SB-T35: usb hub rst gpio request failed: %d\n", err);
+	} else {
+		udelay(10);
+		gpio_set_value(SB_T35_USB_HUB_RESET_GPIO, 1);
+		msleep(1);
+	}
+
+	usbhs_init(&usbhs_bdata);
+}
+
 static int cm_t35_twl_gpio_setup(struct device *dev, unsigned gpio,
 				 unsigned ngpio)
 {
@@ -456,17 +489,14 @@ static struct twl4030_platform_data cm_t35_twldata = {
 	.gpio		= &cm_t35_gpio_data,
 	.vmmc1		= &cm_t35_vmmc1,
 	.vsim		= &cm_t35_vsim,
+	.vio		= &cm_t35_vio,
 };
 
 static void __init cm_t35_init_i2c(void)
 {
 	omap3_pmic_get_config(&cm_t35_twldata, TWL_COMMON_PDATA_USB,
-			TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
-
-	cm_t35_twldata.vpll2->constraints.name = "VDVI";
-	cm_t35_twldata.vpll2->num_consumer_supplies =
-						ARRAY_SIZE(cm_t35_vdvi_supply);
-	cm_t35_twldata.vpll2->consumer_supplies = cm_t35_vdvi_supply;
+			      TWL_COMMON_REGULATOR_VDAC |
+			      TWL_COMMON_PDATA_AUDIO);
 
 	omap3_pmic_init("tps65930", &cm_t35_twldata);
 }
@@ -570,24 +600,28 @@ static void __init cm_t3x_common_dss_mux_init(int mux_mode)
 
 static void __init cm_t35_init_mux(void)
 {
-	omap_mux_init_signal("gpio_70", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
-	omap_mux_init_signal("gpio_71", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
-	omap_mux_init_signal("gpio_72", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
-	omap_mux_init_signal("gpio_73", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
-	omap_mux_init_signal("gpio_74", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
-	omap_mux_init_signal("gpio_75", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
-	cm_t3x_common_dss_mux_init(OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
+	int mux_mode = OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT;
+
+	omap_mux_init_signal("dss_data0.dss_data0", mux_mode);
+	omap_mux_init_signal("dss_data1.dss_data1", mux_mode);
+	omap_mux_init_signal("dss_data2.dss_data2", mux_mode);
+	omap_mux_init_signal("dss_data3.dss_data3", mux_mode);
+	omap_mux_init_signal("dss_data4.dss_data4", mux_mode);
+	omap_mux_init_signal("dss_data5.dss_data5", mux_mode);
+	cm_t3x_common_dss_mux_init(mux_mode);
 }
 
 static void __init cm_t3730_init_mux(void)
 {
-	omap_mux_init_signal("sys_boot0", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
-	omap_mux_init_signal("sys_boot1", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
-	omap_mux_init_signal("sys_boot3", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
-	omap_mux_init_signal("sys_boot4", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
-	omap_mux_init_signal("sys_boot5", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
-	omap_mux_init_signal("sys_boot6", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
-	cm_t3x_common_dss_mux_init(OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
+	int mux_mode = OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT;
+
+	omap_mux_init_signal("sys_boot0", mux_mode);
+	omap_mux_init_signal("sys_boot1", mux_mode);
+	omap_mux_init_signal("sys_boot3", mux_mode);
+	omap_mux_init_signal("sys_boot4", mux_mode);
+	omap_mux_init_signal("sys_boot5", mux_mode);
+	omap_mux_init_signal("sys_boot6", mux_mode);
+	cm_t3x_common_dss_mux_init(mux_mode);
 }
 #else
 static inline void cm_t35_init_mux(void) {}
@@ -612,7 +646,7 @@ static void __init cm_t3x_common_init(void)
 	cm_t35_init_display();
 
 	usb_musb_init(NULL);
-	usbhs_init(&usbhs_bdata);
+	cm_t35_init_usbh();
 }
 
 static void __init cm_t35_init(void)

arch/arm/mach-omap2/board-rx51-peripherals.c

@@ -15,6 +15,7 @@
 #include <linux/input/matrix_keypad.h>
 #include <linux/spi/spi.h>
 #include <linux/wl12xx.h>
+#include <linux/spi/tsc2005.h>
 #include <linux/i2c.h>
 #include <linux/i2c/twl.h>
 #include <linux/clk.h>
@@ -58,6 +59,9 @@
 
 #define RX51_USB_TRANSCEIVER_RST_GPIO	67
 
+#define RX51_TSC2005_RESET_GPIO         104
+#define RX51_TSC2005_IRQ_GPIO           100
+
 /* list all spi devices here */
 enum {
 	RX51_SPI_WL1251,
@@ -66,6 +70,7 @@ enum {
 };
 
 static struct wl12xx_platform_data wl1251_pdata;
+static struct tsc2005_platform_data tsc2005_pdata;
 
 #if defined(CONFIG_SENSORS_TSL2563) || defined(CONFIG_SENSORS_TSL2563_MODULE)
 static struct tsl2563_platform_data rx51_tsl2563_platform_data = {
@@ -167,10 +172,10 @@ static struct spi_board_info rx51_peripherals_spi_board_info[] __initdata = {
 		.modalias		= "tsc2005",
 		.bus_num		= 1,
 		.chip_select		= 0,
-		/* .irq = OMAP_GPIO_IRQ(RX51_TSC2005_IRQ_GPIO),*/
+		.irq			= OMAP_GPIO_IRQ(RX51_TSC2005_IRQ_GPIO),
 		.max_speed_hz		= 6000000,
 		.controller_data	= &tsc2005_mcspi_config,
-		/* .platform_data = &tsc2005_config,*/
+		.platform_data		= &tsc2005_pdata,
 	},
 };
 
@@ -1086,6 +1091,42 @@ static void __init rx51_init_wl1251(void)
 	 */
 }
 
+static struct tsc2005_platform_data tsc2005_pdata = {
+	.ts_pressure_max	= 2048,
+	.ts_pressure_fudge	= 2,
+	.ts_x_max		= 4096,
+	.ts_x_fudge		= 4,
+	.ts_y_max		= 4096,
+	.ts_y_fudge		= 7,
+	.ts_x_plate_ohm		= 280,
+	.esd_timeout_ms		= 8000,
+};
+
+static void rx51_tsc2005_set_reset(bool enable)
+{
+	gpio_set_value(RX51_TSC2005_RESET_GPIO, enable);
+}
+
+static void __init rx51_init_tsc2005(void)
+{
+	int r;
+
+	r = gpio_request_one(RX51_TSC2005_IRQ_GPIO, GPIOF_IN, "tsc2005 IRQ");
+	if (r < 0) {
+		printk(KERN_ERR "unable to get %s GPIO\n", "tsc2005 IRQ");
+		rx51_peripherals_spi_board_info[RX51_SPI_TSC2005].irq = 0;
+	}
+
+	r = gpio_request_one(RX51_TSC2005_RESET_GPIO, GPIOF_OUT_INIT_HIGH,
+		"tsc2005 reset");
+	if (r >= 0) {
+		tsc2005_pdata.set_reset = rx51_tsc2005_set_reset;
+	} else {
+		printk(KERN_ERR "unable to get %s GPIO\n", "tsc2005 reset");
+		tsc2005_pdata.esd_timeout_ms = 0;
+	}
+}
+
 void __init rx51_peripherals_init(void)
 {
 	rx51_i2c_init();
@@ -1094,6 +1135,7 @@ void __init rx51_peripherals_init(void)
 	board_smc91x_init();
 	rx51_add_gpio_keys();
 	rx51_init_wl1251();
+	rx51_init_tsc2005();
 	rx51_init_si4713();
 	spi_register_board_info(rx51_peripherals_spi_board_info,
 				ARRAY_SIZE(rx51_peripherals_spi_board_info));

arch/arm/mach-omap2/board-ti8168evm.c

 /*
- * Code for TI8168 EVM.
+ * Code for TI8168/TI8148 EVM.
  *
  * Copyright (C) 2010 Texas Instruments, Inc. - http://www.ti.com/
  *
@@ -23,16 +23,25 @@
 #include <plat/irqs.h>
 #include <plat/board.h>
 #include "common.h"
+#include <plat/usb.h>
 
-static struct omap_board_config_kernel ti8168_evm_config[] __initdata = {
+static struct omap_musb_board_data musb_board_data = {
+	.set_phy_power	= ti81xx_musb_phy_power,
+	.interface_type	= MUSB_INTERFACE_ULPI,
+	.mode           = MUSB_OTG,
+	.power		= 500,
 };
 
-static void __init ti8168_evm_init(void)
+static struct omap_board_config_kernel ti81xx_evm_config[] __initdata = {
+};
+
+static void __init ti81xx_evm_init(void)
 {
 	omap_serial_init();
 	omap_sdrc_init(NULL, NULL);
-	omap_board_config = ti8168_evm_config;
-	omap_board_config_size = ARRAY_SIZE(ti8168_evm_config);
+	omap_board_config = ti81xx_evm_config;
+	omap_board_config_size = ARRAY_SIZE(ti81xx_evm_config);
+	usb_musb_init(&musb_board_data);
 }
 
 MACHINE_START(TI8168EVM, "ti8168evm")
@@ -42,6 +51,17 @@ MACHINE_START(TI8168EVM, "ti8168evm")
 	.init_early	= ti81xx_init_early,
 	.init_irq	= ti81xx_init_irq,
 	.timer		= &omap3_timer,
-	.init_machine	= ti8168_evm_init,
+	.init_machine	= ti81xx_evm_init,
+	.restart	= omap_prcm_restart,
+MACHINE_END
+
+MACHINE_START(TI8148EVM, "ti8148evm")
+	/* Maintainer: Texas Instruments */
+	.atag_offset	= 0x100,
+	.map_io		= ti81xx_map_io,
+	.init_early	= ti81xx_init_early,
+	.init_irq	= ti81xx_init_irq,
+	.timer		= &omap3_timer,
+	.init_machine	= ti81xx_evm_init,
 	.restart	= omap_prcm_restart,
 MACHINE_END

arch/arm/mach-omap2/devices.c

@@ -336,6 +336,27 @@ static void omap_init_mcpdm(void)
 static inline void omap_init_mcpdm(void) {}
 #endif
 
+#if defined(CONFIG_SND_OMAP_SOC_DMIC) || \
+		defined(CONFIG_SND_OMAP_SOC_DMIC_MODULE)
+
+static void omap_init_dmic(void)
+{
+	struct omap_hwmod *oh;
+	struct platform_device *pdev;
+
+	oh = omap_hwmod_lookup("dmic");
+	if (!oh) {
+		printk(KERN_ERR "Could not look up mcpdm hw_mod\n");
+		return;
+	}
+
+	pdev = omap_device_build("omap-dmic", -1, oh, NULL, 0, NULL, 0, 0);
+	WARN(IS_ERR(pdev), "Can't build omap_device for omap-dmic.\n");
+}
+#else
+static inline void omap_init_dmic(void) {}
+#endif
+
 #if defined(CONFIG_SPI_OMAP24XX) || defined(CONFIG_SPI_OMAP24XX_MODULE)
 
 #include <plat/mcspi.h>
@@ -681,6 +702,7 @@ static int __init omap2_init_devices(void)
 	 */
 	omap_init_audio();
 	omap_init_mcpdm();
+	omap_init_dmic();
 	omap_init_camera();
 	omap_init_mbox();
 	omap_init_mcspi();

arch/arm/mach-omap2/omap_phy_internal.c

@@ -260,3 +260,38 @@ void am35x_set_mode(u8 musb_mode)
 
 	omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);
 }
+
+void ti81xx_musb_phy_power(u8 on)
+{
+	void __iomem *scm_base = NULL;
+	u32 usbphycfg;
+
+	scm_base = ioremap(TI81XX_SCM_BASE, SZ_2K);
+	if (!scm_base) {
+		pr_err("system control module ioremap failed\n");
+		return;
+	}
+
+	usbphycfg = __raw_readl(scm_base + USBCTRL0);
+
+	if (on) {
+		if (cpu_is_ti816x()) {
+			usbphycfg |= TI816X_USBPHY0_NORMAL_MODE;
+			usbphycfg &= ~TI816X_USBPHY_REFCLK_OSC;
+		} else if (cpu_is_ti814x()) {
+			usbphycfg &= ~(USBPHY_CM_PWRDN | USBPHY_OTG_PWRDN
+				| USBPHY_DPINPUT | USBPHY_DMINPUT);
+			usbphycfg |= (USBPHY_OTGVDET_EN | USBPHY_OTGSESSEND_EN
+				| USBPHY_DPOPBUFCTL | USBPHY_DMOPBUFCTL);
+		}
+	} else {
+		if (cpu_is_ti816x())
+			usbphycfg &= ~TI816X_USBPHY0_NORMAL_MODE;
+		else if (cpu_is_ti814x())
+			usbphycfg |= USBPHY_CM_PWRDN | USBPHY_OTG_PWRDN;
+
+	}
+	__raw_writel(usbphycfg, scm_base + USBCTRL0);
+
+	iounmap(scm_base);
+}

arch/arm/mach-omap2/sdram-nokia.c

 /*
  * SDRC register values for Nokia boards
  *
- * Copyright (C) 2008, 2010 Nokia Corporation
+ * Copyright (C) 2008, 2010-2011 Nokia Corporation
  *
  * Lauri Leukkunen <lauri.leukkunen@nokia.com>
  *
@@ -107,14 +107,37 @@ static const struct sdram_timings nokia_195dot2mhz_timings[] = {
 	},
 };
 
+static const struct sdram_timings nokia_200mhz_timings[] = {
+	{
+		.casl = 3,
+		.tDAL = 30000,
+		.tDPL = 15000,
+		.tRRD = 10000,
+		.tRCD = 20000,
+		.tRP = 15000,
+		.tRAS = 40000,
+		.tRC = 55000,
+		.tRFC = 140000,
+		.tXSR = 200000,
+
+		.tREF = 7800,
+
+		.tXP = 2,
+		.tCKE = 4,
+		.tWTR = 2
+	},
+};
+
 static const struct {
 	long rate;
 	struct sdram_timings const *data;
 } nokia_timings[] = {
 	{ 83000000, nokia_166mhz_timings },
 	{ 97600000, nokia_97dot6mhz_timings },
+	{ 100000000, nokia_200mhz_timings },
 	{ 166000000, nokia_166mhz_timings },
 	{ 195200000, nokia_195dot2mhz_timings },
+	{ 200000000, nokia_200mhz_timings },
 };
 static struct omap_sdrc_params nokia_sdrc_params[ARRAY_SIZE(nokia_timings) + 1];
 

arch/arm/mach-omap2/usb-musb.c

@@ -93,6 +93,9 @@ void __init usb_musb_init(struct omap_musb_board_data *musb_board_data)
 	if (cpu_is_omap3517() || cpu_is_omap3505()) {
 		oh_name = "am35x_otg_hs";
 		name = "musb-am35x";
+	} else if (cpu_is_ti81xx()) {
+		oh_name = "usb_otg_hs";
+		name = "musb-ti81xx";
 	} else {
 		oh_name = "usb_otg_hs";
 		name = "musb-omap2430";

arch/arm/mach-pxa/mioa701.c

@@ -53,6 +53,7 @@
 #include <mach/pxa27x-udc.h>
 #include <mach/camera.h>
 #include <mach/audio.h>
+#include <mach/smemc.h>
 #include <media/soc_camera.h>
 
 #include <mach/mioa701.h>
@@ -390,24 +391,19 @@ static struct pxamci_platform_data mioa701_mci_info = {
 };
 
 /* FlashRAM */
-static struct resource strataflash_resource = {
+static struct resource docg3_resource = {
 	.start = PXA_CS0_PHYS,
-	.end   = PXA_CS0_PHYS + SZ_64M - 1,
+	.end   = PXA_CS0_PHYS + SZ_8K - 1,
 	.flags = IORESOURCE_MEM,
 };
 
-static struct physmap_flash_data strataflash_data = {
-	.width = 2,
-	/* .set_vpp = mioa701_set_vpp, */
-};
-
-static struct platform_device strataflash = {
-	.name	       = "physmap-flash",
+static struct platform_device docg3 = {
+	.name	       = "docg3",
 	.id	       = -1,
-	.resource      = &strataflash_resource,
+	.resource      = &docg3_resource,
 	.num_resources = 1,
 	.dev = {
-		.platform_data = &strataflash_data,
+		.platform_data = NULL,
 	},
 };
 
@@ -685,7 +681,7 @@ static struct platform_device *devices[] __initdata = {
 	&pxa2xx_pcm,
 	&mioa701_sound,
 	&power_dev,
-	&strataflash,
+	&docg3,
 	&gpio_vbus,
 	&mioa701_camera,
 	&mioa701_board,
@@ -720,6 +716,15 @@ static void __init mioa701_machine_init(void)
 	RTTR = 32768 - 1; /* Reset crazy WinCE value */
 	UP2OCR = UP2OCR_HXOE;
 
+	/*
+	 * Set up the flash memory : DiskOnChip G3 on first static memory bank
+	 */
+	__raw_writel(0x7ff02dd8, MSC0);
+	__raw_writel(0x0001c391, MCMEM0);
+	__raw_writel(0x0001c391, MCATT0);
+	__raw_writel(0x0001c391, MCIO0);
+
+
 	pxa2xx_mfp_config(ARRAY_AND_SIZE(mioa701_pin_config));
 	pxa_set_ffuart_info(NULL);
 	pxa_set_btuart_info(NULL);

arch/arm/mach-s3c2440/mach-mini2440.c

@@ -169,6 +169,24 @@ static struct s3c2410fb_display mini2440_lcd_cfg[] __initdata = {
 		.lcdcon5	= (S3C2410_LCDCON5_FRM565 |
 				   S3C2410_LCDCON5_HWSWP),
 	},
+	/* mini2440 + 3.5" TFT (LCD-W35i, LQ035Q1DG06 type) + touchscreen*/
+	[3] = {
+		_LCD_DECLARE(
+			/* clock */
+			7,
+			/* xres, margin_right, margin_left, hsync */
+			320, 68, 66, 4,
+			/* yres, margin_top, margin_bottom, vsync */
+			240, 4, 4, 9,
+			/* refresh rate */
+			60),
+		.lcdcon5	= (S3C2410_LCDCON5_FRM565 |
+				   S3C2410_LCDCON5_INVVDEN |
+				   S3C2410_LCDCON5_INVVFRAME |
+				   S3C2410_LCDCON5_INVVLINE |
+				   S3C2410_LCDCON5_INVVCLK |
+				   S3C2410_LCDCON5_HWSWP),
+	},
 };
 
 /* todo - put into gpio header */

arch/arm/mach-s3c64xx/Kconfig

@@ -194,7 +194,7 @@ config SMDK6410_WM1190_EV1
 	depends on MACH_SMDK6410
 	select REGULATOR
 	select REGULATOR_WM8350
-	select S3C24XX_GPIO_EXTRA64
+	select SAMSUNG_GPIO_EXTRA64
 	select MFD_WM8350_I2C
 	select MFD_WM8350_CONFIG_MODE_0
 	select MFD_WM8350_CONFIG_MODE_3
@@ -212,7 +212,7 @@ config SMDK6410_WM1192_EV1
 	depends on MACH_SMDK6410
 	select REGULATOR
 	select REGULATOR_WM831X
-	select S3C24XX_GPIO_EXTRA64
+	select SAMSUNG_GPIO_EXTRA64
 	select MFD_WM831X
 	select MFD_WM831X_I2C
 	help
@@ -294,7 +294,7 @@ config MACH_WLF_CRAGG_6410
 	select S3C_DEV_WDT
 	select S3C_DEV_RTC
 	select S3C64XX_DEV_SPI0
-	select S3C24XX_GPIO_EXTRA128
+	select SAMSUNG_GPIO_EXTRA128
 	select I2C
 	help
 	  Machine support for the Wolfson Cragganmore S3C6410 variant.

arch/arm/mach-s3c64xx/include/mach/crag6410.h

@@ -15,9 +15,11 @@
 
 #define BANFF_PMIC_IRQ_BASE		IRQ_BOARD_START
 #define GLENFARCLAS_PMIC_IRQ_BASE	(IRQ_BOARD_START + 64)
+#define CODEC_IRQ_BASE			(IRQ_BOARD_START + 128)
 
 #define PCA935X_GPIO_BASE		GPIO_BOARD_START
-#define CODEC_GPIO_BASE		(GPIO_BOARD_START + 8)
-#define GLENFARCLAS_PMIC_GPIO_BASE	(GPIO_BOARD_START + 16)
+#define CODEC_GPIO_BASE			(GPIO_BOARD_START + 8)
+#define GLENFARCLAS_PMIC_GPIO_BASE	(GPIO_BOARD_START + 32)
+#define BANFF_PMIC_GPIO_BASE		(GPIO_BOARD_START + 64)
 
 #endif

arch/arm/mach-s3c64xx/include/mach/gpio.h

@@ -88,6 +88,6 @@ enum s3c_gpio_number {
 /* define the number of gpios we need to the one after the GPQ() range */
 #define GPIO_BOARD_START (S3C64XX_GPQ(S3C64XX_GPIO_Q_NR) + 1)
 
-#define BOARD_NR_GPIOS 16
+#define BOARD_NR_GPIOS	(16 + CONFIG_SAMSUNG_GPIO_EXTRA)
 
 #define ARCH_NR_GPIOS	(GPIO_BOARD_START + BOARD_NR_GPIOS)

arch/arm/mach-s3c64xx/include/mach/irqs.h

@@ -169,7 +169,7 @@
 #define IRQ_BOARD_START (IRQ_EINT_GROUP9_BASE + IRQ_EINT_GROUP9_NR + 1)
 
 #ifdef CONFIG_MACH_WLF_CRAGG_6410
-#define IRQ_BOARD_NR 128
+#define IRQ_BOARD_NR 160
 #elif defined(CONFIG_SMDK6410_WM1190_EV1)
 #define IRQ_BOARD_NR 64
 #elif defined(CONFIG_SMDK6410_WM1192_EV1)

arch/arm/mach-s3c64xx/mach-crag6410-module.c

@@ -14,13 +14,43 @@
 
 #include <linux/mfd/wm831x/irq.h>
 #include <linux/mfd/wm831x/gpio.h>
+#include <linux/mfd/wm8994/pdata.h>
 
+#include <sound/wm5100.h>
 #include <sound/wm8996.h>
 #include <sound/wm8962.h>
 #include <sound/wm9081.h>
 
 #include <mach/crag6410.h>
 
+static struct wm5100_pdata wm5100_pdata = {
+	.ldo_ena = S3C64XX_GPN(7),
+	.irq_flags = IRQF_TRIGGER_HIGH,
+	.gpio_base = CODEC_GPIO_BASE,
+
+	.in_mode = {
+		WM5100_IN_DIFF,
+		WM5100_IN_DIFF,
+		WM5100_IN_DIFF,
+		WM5100_IN_SE,
+	},
+
+	.hp_pol = CODEC_GPIO_BASE + 3,
+	.jack_modes = {
+		{ WM5100_MICDET_MICBIAS3, 0, 0 },
+		{ WM5100_MICDET_MICBIAS2, 1, 1 },
+	},
+
+	.gpio_defaults = {
+		0,
+		0,
+		0,
+		0,
+		0x2, /* IRQ: CMOS output */
+		0x3, /* CLKOUT: CMOS output */
+	},
+};
+
 static struct wm8996_retune_mobile_config wm8996_retune[] = {
 	{
 		.name = "Sub LPF",
@@ -72,7 +102,6 @@ static struct wm8962_pdata wm8962_pdata __initdata = {
 		0x8000 | WM8962_GPIO_FN_DMICDAT,
 		WM8962_GPIO_FN_IRQ,    /* Open drain mode */
 	},
-	.irq_active_low = true,
 };
 
 static struct wm9081_pdata wm9081_pdata __initdata = {
@@ -91,6 +120,7 @@ static const struct i2c_board_info wm1254_devs[] = {
 
 static const struct i2c_board_info wm1255_devs[] = {
 	{ I2C_BOARD_INFO("wm5100", 0x1a),
+	  .platform_data = &wm5100_pdata,
 	  .irq = GLENFARCLAS_PMIC_IRQ_BASE + WM831X_IRQ_GPIO_2,
 	},
 	{ I2C_BOARD_INFO("wm9081", 0x6c),
@@ -104,6 +134,24 @@ static const struct i2c_board_info wm1259_devs[] = {
 	},
 };
 
+static struct wm8994_pdata wm8994_pdata = {
+	.gpio_base = CODEC_GPIO_BASE,
+	.gpio_defaults = {
+		0x3,          /* IRQ out, active high, CMOS */
+	},
+	.irq_base = CODEC_IRQ_BASE,
+	.ldo = {
+		{ .supply = "WALLVDD" },
+		{ .supply = "WALLVDD" },
+	},
+};
+
+static const struct i2c_board_info wm1277_devs[] = {
+	{ I2C_BOARD_INFO("wm8958", 0x1a),  /* WM8958 is the superset */
+	  .platform_data = &wm8994_pdata,
+	  .irq = GLENFARCLAS_PMIC_IRQ_BASE + WM831X_IRQ_GPIO_2,
+	},
+};
 
 static __devinitdata const struct {
 	u8 id;
@@ -125,6 +173,8 @@ static __devinitdata const struct {
 	{ .id = 0x3b, .name = "1255-EV1 Kilchoman",
 	  .i2c_devs = wm1255_devs, .num_i2c_devs = ARRAY_SIZE(wm1255_devs) },
 	{ .id = 0x3c, .name = "1273-EV1 Longmorn" },
+	{ .id = 0x3d, .name = "1277-EV1 Littlemill",
+	  .i2c_devs = wm1277_devs, .num_i2c_devs = ARRAY_SIZE(wm1277_devs) },
 };
 
 static __devinit int wlf_gf_module_probe(struct i2c_client *i2c,
@@ -154,8 +204,8 @@ static __devinit int wlf_gf_module_probe(struct i2c_client *i2c,
 					"Failed to register dev: %d\n", ret);
 		}
 	} else {
-		dev_warn(&i2c->dev, "Unknown module ID %d revision %d\n",
-			 id, rev);
+		dev_warn(&i2c->dev, "Unknown module ID 0x%x revision %d\n",
+			 id, rev + 1);
 	}
 
 	return 0;

arch/arm/mach-s3c64xx/mach-crag6410.c

@@ -37,6 +37,8 @@
 #include <linux/mfd/wm831x/irq.h>
 #include <linux/mfd/wm831x/gpio.h>
 
+#include <sound/wm1250-ev1.h>
+
 #include <asm/hardware/vic.h>
 #include <asm/mach/arch.h>
 #include <asm/mach-types.h>
@@ -289,6 +291,11 @@ static struct platform_device speyside_wm8962_device = {
 	.id		= -1,
 };
 
+static struct platform_device littlemill_device = {
+	.name		= "littlemill",
+	.id		= -1,
+};
+
 static struct regulator_consumer_supply wallvdd_consumers[] = {
 	REGULATOR_SUPPLY("SPKVDD1", "1-001a"),
 	REGULATOR_SUPPLY("SPKVDD2", "1-001a"),
@@ -341,6 +348,7 @@ static struct platform_device *crag6410_devices[] __initdata = {
 	&crag6410_backlight_device,
 	&speyside_device,
 	&speyside_wm8962_device,
+	&littlemill_device,
 	&lowland_device,
 	&wallvdd_device,
 };
@@ -374,6 +382,10 @@ static struct regulator_init_data vddarm __initdata = {
 	.driver_data = &vddarm_pdata,
 };
 
+static struct regulator_consumer_supply vddint_consumers[] __initdata = {
+	REGULATOR_SUPPLY("vddint", NULL),
+};
+
 static struct regulator_init_data vddint __initdata = {
 	.constraints = {
 		.name = "VDDINT",
@@ -382,6 +394,9 @@ static struct regulator_init_data vddint __initdata = {
 		.always_on = 1,
 		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
 	},
+	.num_consumer_supplies = ARRAY_SIZE(vddint_consumers),
+	.consumer_supplies = vddint_consumers,
+	.supply_regulator = "WALLVDD",
 };
 
 static struct regulator_init_data vddmem __initdata = {
@@ -502,7 +517,8 @@ static struct wm831x_touch_pdata touch_pdata __initdata = {
 static struct wm831x_pdata crag_pmic_pdata __initdata = {
 	.wm831x_num = 1,
 	.irq_base = BANFF_PMIC_IRQ_BASE,
-	.gpio_base = GPIO_BOARD_START + 8,
+	.gpio_base = BANFF_PMIC_GPIO_BASE,
+	.soft_shutdown = true,
 
 	.backup = &banff_backup_pdata,
 
@@ -607,6 +623,7 @@ static struct wm831x_pdata glenfarclas_pmic_pdata __initdata = {
 	.wm831x_num = 2,
 	.irq_base = GLENFARCLAS_PMIC_IRQ_BASE,
 	.gpio_base = GLENFARCLAS_PMIC_GPIO_BASE,
+	.soft_shutdown = true,
 
 	.gpio_defaults = {
 		/* GPIO1-3: IRQ inputs, rising edge triggered, CMOS */
@@ -624,6 +641,16 @@ static struct wm831x_pdata glenfarclas_pmic_pdata __initdata = {
 	.disable_touch = true,
 };
 
+static struct wm1250_ev1_pdata wm1250_ev1_pdata = {
+	.gpios = {
+		[WM1250_EV1_GPIO_CLK_ENA] = S3C64XX_GPN(12),
+		[WM1250_EV1_GPIO_CLK_SEL0] = S3C64XX_GPL(12),
+		[WM1250_EV1_GPIO_CLK_SEL1] = S3C64XX_GPL(13),
+		[WM1250_EV1_GPIO_OSR] = S3C64XX_GPL(14),
+		[WM1250_EV1_GPIO_MASTER] = S3C64XX_GPL(8),
+	},
+};
+
 static struct i2c_board_info i2c_devs1[] __initdata = {
 	{ I2C_BOARD_INFO("wm8311", 0x34),
 	  .irq = S3C_EINT(0),
@@ -633,7 +660,13 @@ static struct i2c_board_info i2c_devs1[] __initdata = {
 	{ I2C_BOARD_INFO("wlf-gf-module", 0x25) },
 	{ I2C_BOARD_INFO("wlf-gf-module", 0x26) },
 
-	{ I2C_BOARD_INFO("wm1250-ev1", 0x27) },
+	{ I2C_BOARD_INFO("wm1250-ev1", 0x27),
+	  .platform_data = &wm1250_ev1_pdata },
+};
+
+static struct s3c2410_platform_i2c i2c1_pdata = {
+	.frequency = 400000,
+	.bus_num = 1,
 };
 
 static void __init crag6410_map_io(void)
@@ -694,7 +727,7 @@ static void __init crag6410_machine_init(void)
 	s3c_sdhci2_set_platdata(&crag6410_hsmmc2_pdata);
 
 	s3c_i2c0_set_platdata(&i2c0_pdata);
-	s3c_i2c1_set_platdata(NULL);
+	s3c_i2c1_set_platdata(&i2c1_pdata);
 	s3c_fb_set_platdata(&crag6410_lcd_pdata);
 
 	i2c_register_board_info(0, i2c_devs0, ARRAY_SIZE(i2c_devs0));

arch/arm/mach-s3c64xx/pm.c

@@ -346,10 +346,23 @@ int __init s3c64xx_pm_init(void)
 
 static __init int s3c64xx_pm_initcall(void)
 {
+	u32 val;
+
 	pm_cpu_prep = s3c64xx_pm_prepare;
 	pm_cpu_sleep = s3c64xx_cpu_suspend;
 	pm_uart_udivslot = 1;
 
+	/*
+	 * Unconditionally disable power domains that contain only
+	 * blocks which have no mainline driver support.
+	 */
+	val = __raw_readl(S3C64XX_NORMAL_CFG);
+	val &= ~(S3C64XX_NORMALCFG_DOMAIN_G_ON |
+		 S3C64XX_NORMALCFG_DOMAIN_V_ON |
+		 S3C64XX_NORMALCFG_DOMAIN_I_ON |
+		 S3C64XX_NORMALCFG_DOMAIN_P_ON);
+	__raw_writel(val, S3C64XX_NORMAL_CFG);
+
 #ifdef CONFIG_S3C_PM_DEBUG_LED_SMDK
 	gpio_request(S3C64XX_GPN(12), "DEBUG_LED0");
 	gpio_request(S3C64XX_GPN(13), "DEBUG_LED1");

arch/arm/mach-tegra/Makefile

+obj-y                                   += board-pinmux.o
 obj-y                                   += common.o
 obj-y                                   += devices.o
 obj-y                                   += io.o

arch/arm/mach-tegra/board-dt-tegra20.c

@@ -54,6 +54,8 @@ void trimslice_pinmux_init(void);
 void ventana_pinmux_init(void);
 
 struct of_dev_auxdata tegra20_auxdata_lookup[] __initdata = {
+	OF_DEV_AUXDATA("nvidia,tegra20-pinmux", TEGRA_APB_MISC_BASE + 0x14, "tegra-pinmux", NULL),
+	OF_DEV_AUXDATA("nvidia,tegra20-gpio", TEGRA_GPIO_BASE, "tegra-gpio", NULL),
 	OF_DEV_AUXDATA("nvidia,tegra20-sdhci", TEGRA_SDMMC1_BASE, "sdhci-tegra.0", NULL),
 	OF_DEV_AUXDATA("nvidia,tegra20-sdhci", TEGRA_SDMMC2_BASE, "sdhci-tegra.1", NULL),
 	OF_DEV_AUXDATA("nvidia,tegra20-sdhci", TEGRA_SDMMC3_BASE, "sdhci-tegra.2", NULL),
@@ -110,13 +112,6 @@ static void __init tegra_dt_init(void)
 
 	tegra_clk_init_from_table(tegra_dt_clk_init_table);
 
-	/*
-	 * Finished with the static registrations now; fill in the missing
-	 * devices
-	 */
-	of_platform_populate(NULL, tegra_dt_match_table,
-				tegra20_auxdata_lookup, NULL);
-
 	for (i = 0; i < ARRAY_SIZE(pinmux_configs); i++) {
 		if (of_machine_is_compatible(pinmux_configs[i].machine)) {
 			pinmux_configs[i].init();
@@ -126,6 +121,13 @@ static void __init tegra_dt_init(void)
 
 	WARN(i == ARRAY_SIZE(pinmux_configs),
 		"Unknown platform! Pinmuxing not initialized\n");
+
+	/*
+	 * Finished with the static registrations now; fill in the missing
+	 * devices
+	 */
+	of_platform_populate(NULL, tegra_dt_match_table,
+				tegra20_auxdata_lookup, NULL);
 }
 
 static const char *tegra20_dt_board_compat[] = {

arch/arm/mach-tegra/board-harmony-pcie.c

@@ -22,8 +22,6 @@
 
 #include <asm/mach-types.h>
 
-#include <mach/pinmux.h>
-#include <mach/pinmux-tegra20.h>
 #include "board.h"
 #include "board-harmony.h"
 
@@ -49,10 +47,6 @@ static int __init harmony_pcie_init(void)
 
 	regulator_enable(regulator);
 
-	tegra_pinmux_set_tristate(TEGRA_PINGROUP_GPV, TEGRA_TRI_NORMAL);
-	tegra_pinmux_set_tristate(TEGRA_PINGROUP_SLXA, TEGRA_TRI_NORMAL);
-	tegra_pinmux_set_tristate(TEGRA_PINGROUP_SLXK, TEGRA_TRI_NORMAL);
-
 	err = tegra_pcie_init(true, true);
 	if (err)
 		goto err_pcie;
@@ -60,10 +54,6 @@ static int __init harmony_pcie_init(void)
 	return 0;
 
 err_pcie:
-	tegra_pinmux_set_tristate(TEGRA_PINGROUP_GPV, TEGRA_TRI_TRISTATE);
-	tegra_pinmux_set_tristate(TEGRA_PINGROUP_SLXA, TEGRA_TRI_TRISTATE);
-	tegra_pinmux_set_tristate(TEGRA_PINGROUP_SLXK, TEGRA_TRI_TRISTATE);
-
 	regulator_disable(regulator);
 	regulator_put(regulator);
 err_reg:

arch/arm/mach-tegra/board-harmony-pinmux.c

@@ -23,7 +23,7 @@
 
 #include "gpio-names.h"
 #include "board-harmony.h"
-#include "devices.h"
+#include "board-pinmux.h"
 
 static struct tegra_pingroup_config harmony_pinmux[] = {
 	{TEGRA_PINGROUP_ATA,   TEGRA_MUX_IDE,           TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
@@ -144,11 +144,6 @@ static struct tegra_pingroup_config harmony_pinmux[] = {
 	{TEGRA_PINGROUP_XM2D,  TEGRA_MUX_NONE,          TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
 };
 
-static struct platform_device *pinmux_devices[] = {
-	&tegra_gpio_device,
-	&tegra_pinmux_device,
-};
-
 static struct tegra_gpio_table gpio_table[] = {
 	{ .gpio = TEGRA_GPIO_SD2_CD,		.enable = true	},
 	{ .gpio = TEGRA_GPIO_SD2_WP,		.enable = true	},
@@ -162,13 +157,14 @@ static struct tegra_gpio_table gpio_table[] = {
 	{ .gpio = TEGRA_GPIO_EXT_MIC_EN,	.enable = true	},
 };
 
+static struct tegra_board_pinmux_conf conf = {
+	.pgs = harmony_pinmux,
+	.pg_count = ARRAY_SIZE(harmony_pinmux),
+	.gpios = gpio_table,
+	.gpio_count = ARRAY_SIZE(gpio_table),
+};
+
 void harmony_pinmux_init(void)
 {
-	if (!of_machine_is_compatible("nvidia,tegra20"))
-		platform_add_devices(pinmux_devices,
-					ARRAY_SIZE(pinmux_devices));
-
-	tegra_pinmux_config_table(harmony_pinmux, ARRAY_SIZE(harmony_pinmux));
-
-	tegra_gpio_config(gpio_table, ARRAY_SIZE(gpio_table));
+	tegra_board_pinmux_init(&conf, NULL);
 }

arch/arm/mach-tegra/board-paz00-pinmux.c

@@ -23,7 +23,7 @@
 
 #include "gpio-names.h"
 #include "board-paz00.h"
-#include "devices.h"
+#include "board-pinmux.h"
 
 static struct tegra_pingroup_config paz00_pinmux[] = {
 	{TEGRA_PINGROUP_ATA,   TEGRA_MUX_GMI,           TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
@@ -31,7 +31,7 @@ static struct tegra_pingroup_config paz00_pinmux[] = {
 	{TEGRA_PINGROUP_ATC,   TEGRA_MUX_GMI,           TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_ATD,   TEGRA_MUX_GMI,           TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_ATE,   TEGRA_MUX_GMI,           TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
-	{TEGRA_PINGROUP_CDEV1, TEGRA_MUX_PLLA_OUT,      TEGRA_PUPD_PULL_DOWN, TEGRA_TRI_TRISTATE},
+	{TEGRA_PINGROUP_CDEV1, TEGRA_MUX_PLLA_OUT,      TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_CDEV2, TEGRA_MUX_PLLP_OUT4,     TEGRA_PUPD_PULL_DOWN, TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_CRTP,  TEGRA_MUX_CRT,           TEGRA_PUPD_NORMAL,    TEGRA_TRI_TRISTATE},
 	{TEGRA_PINGROUP_CSUS,  TEGRA_MUX_PLLC_OUT1,     TEGRA_PUPD_PULL_DOWN, TEGRA_TRI_TRISTATE},
@@ -144,11 +144,6 @@ static struct tegra_pingroup_config paz00_pinmux[] = {
 	{TEGRA_PINGROUP_XM2D,  TEGRA_MUX_NONE,          TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
 };
 
-static struct platform_device *pinmux_devices[] = {
-	&tegra_gpio_device,
-	&tegra_pinmux_device,
-};
-
 static struct tegra_gpio_table gpio_table[] = {
 	{ .gpio = TEGRA_GPIO_SD1_CD,	.enable = true },
 	{ .gpio = TEGRA_GPIO_SD1_WP,	.enable = true },
@@ -159,13 +154,14 @@ static struct tegra_gpio_table gpio_table[] = {
 	{ .gpio = TEGRA_WIFI_LED,	.enable = true },
 };
 
+static struct tegra_board_pinmux_conf conf = {
+	.pgs = paz00_pinmux,
+	.pg_count = ARRAY_SIZE(paz00_pinmux),
+	.gpios = gpio_table,
+	.gpio_count = ARRAY_SIZE(gpio_table),
+};
+
 void paz00_pinmux_init(void)
 {
-	if (!of_machine_is_compatible("nvidia,tegra20"))
-		platform_add_devices(pinmux_devices,
-					ARRAY_SIZE(pinmux_devices));
-
-	tegra_pinmux_config_table(paz00_pinmux, ARRAY_SIZE(paz00_pinmux));
-
-	tegra_gpio_config(gpio_table, ARRAY_SIZE(gpio_table));
+	tegra_board_pinmux_init(&conf, NULL);
 }

arch/arm/mach-tegra/board-paz00.c

@@ -23,8 +23,10 @@
 #include <linux/serial_8250.h>
 #include <linux/clk.h>
 #include <linux/dma-mapping.h>
+#include <linux/gpio_keys.h>
 #include <linux/pda_power.h>
 #include <linux/io.h>
+#include <linux/input.h>
 #include <linux/i2c.h>
 #include <linux/gpio.h>
 #include <linux/rfkill-gpio.h>
@@ -115,12 +117,37 @@ static struct platform_device leds_gpio = {
         },
 };
 
+static struct gpio_keys_button paz00_gpio_keys_buttons[] = {
+	{
+		.code		= KEY_POWER,
+		.gpio		= TEGRA_GPIO_POWERKEY,
+		.active_low	= 1,
+		.desc		= "Power",
+		.type		= EV_KEY,
+		.wakeup		= 1,
+	},
+};
+
+static struct gpio_keys_platform_data paz00_gpio_keys = {
+	.buttons	= paz00_gpio_keys_buttons,
+	.nbuttons	= ARRAY_SIZE(paz00_gpio_keys_buttons),
+};
+
+static struct platform_device gpio_keys_device = {
+	.name	= "gpio-keys",
+	.id	= -1,
+	.dev	= {
+		.platform_data = &paz00_gpio_keys,
+	},
+};
+
 static struct platform_device *paz00_devices[] __initdata = {
 	&debug_uart,
 	&tegra_sdhci_device4,
 	&tegra_sdhci_device1,
 	&wifi_rfkill_device,
 	&leds_gpio,
+	&gpio_keys_device,
 };
 
 static void paz00_i2c_init(void)

arch/arm/mach-tegra/board-paz00.h

@@ -32,6 +32,9 @@
 #define TEGRA_WIFI_RST			TEGRA_GPIO_PD1
 #define TEGRA_WIFI_LED			TEGRA_GPIO_PD0
 
+/* WakeUp */
+#define TEGRA_GPIO_POWERKEY	TEGRA_GPIO_PJ7
+
 void paz00_pinmux_init(void);
 
 #endif

arch/arm/mach-tegra/board-pinmux.c

+/*
+ * Copyright (c) 2011, NVIDIA CORPORATION.  All rights reserved.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/device.h>
+#include <linux/kernel.h>
+#include <linux/notifier.h>
+#include <linux/of.h>
+#include <linux/string.h>
+
+#include <mach/gpio-tegra.h>
+#include <mach/pinmux.h>
+
+#include "board-pinmux.h"
+#include "devices.h"
+
+struct tegra_board_pinmux_conf *confs[2];
+
+static void tegra_board_pinmux_setup_gpios(void)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(confs); i++) {
+		if (!confs[i])
+			continue;
+
+		tegra_gpio_config(confs[i]->gpios, confs[i]->gpio_count);
+	}
+}
+
+static void tegra_board_pinmux_setup_pinmux(void)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(confs); i++) {
+		if (!confs[i])
+			continue;
+
+		tegra_pinmux_config_table(confs[i]->pgs, confs[i]->pg_count);
+
+		if (confs[i]->drives)
+			tegra_drive_pinmux_config_table(confs[i]->drives,
+							confs[i]->drive_count);
+	}
+}
+
+static int tegra_board_pinmux_bus_notify(struct notifier_block *nb,
+					 unsigned long event, void *vdev)
+{
+	static bool had_gpio;
+	static bool had_pinmux;
+
+	struct device *dev = vdev;
+	const char *devname;
+
+	if (event != BUS_NOTIFY_BOUND_DRIVER)
+		return NOTIFY_DONE;
+
+	devname = dev_name(dev);
+
+	if (!had_gpio && !strcmp(devname, GPIO_DEV)) {
+		tegra_board_pinmux_setup_gpios();
+		had_gpio = true;
+	} else if (!had_pinmux && !strcmp(devname, PINMUX_DEV)) {
+		tegra_board_pinmux_setup_pinmux();
+		had_pinmux = true;
+	}
+
+	if (had_gpio && had_pinmux)
+		return NOTIFY_STOP_MASK;
+	else
+		return NOTIFY_DONE;
+}
+
+static struct notifier_block nb = {
+	.notifier_call = tegra_board_pinmux_bus_notify,
+};
+
+static struct platform_device *devices[] = {
+	&tegra_gpio_device,
+	&tegra_pinmux_device,
+};
+
+void tegra_board_pinmux_init(struct tegra_board_pinmux_conf *conf_a,
+			     struct tegra_board_pinmux_conf *conf_b)
+{
+	confs[0] = conf_a;
+	confs[1] = conf_b;
+
+	bus_register_notifier(&platform_bus_type, &nb);
+
+	if (!of_machine_is_compatible("nvidia,tegra20"))
+		platform_add_devices(devices, ARRAY_SIZE(devices));
+}

arch/arm/mach-tegra/board-pinmux.h

+/*
+ * Copyright (c) 2011, NVIDIA CORPORATION.  All rights reserved.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef __MACH_TEGRA_BOARD_PINMUX_H
+#define __MACH_TEGRA_BOARD_PINMUX_H
+
+#define GPIO_DEV "tegra-gpio"
+#define PINMUX_DEV "tegra-pinmux"
+
+struct tegra_pingroup_config;
+struct tegra_gpio_table;
+
+struct tegra_board_pinmux_conf {
+	struct tegra_pingroup_config *pgs;
+	int pg_count;
+
+	struct tegra_drive_pingroup_config *drives;
+	int drive_count;
+
+	struct tegra_gpio_table *gpios;
+	int gpio_count;
+};
+
+void tegra_board_pinmux_init(struct tegra_board_pinmux_conf *conf_a,
+			     struct tegra_board_pinmux_conf *conf_b);
+
+#endif

arch/arm/mach-tegra/board-seaboard-pinmux.c

@@ -22,8 +22,8 @@
 #include <mach/pinmux-tegra20.h>
 
 #include "gpio-names.h"
+#include "board-pinmux.h"
 #include "board-seaboard.h"
-#include "devices.h"
 
 #define DEFAULT_DRIVE(_name)					\
 	{							\
@@ -37,11 +37,11 @@
 		.slew_falling = TEGRA_SLEW_SLOWEST,		\
 	}
 
-static __initdata struct tegra_drive_pingroup_config seaboard_drive_pinmux[] = {
+static struct tegra_drive_pingroup_config seaboard_drive_pinmux[] = {
 	DEFAULT_DRIVE(SDIO1),
 };
 
-static __initdata struct tegra_pingroup_config seaboard_pinmux[] = {
+static struct tegra_pingroup_config common_pinmux[] = {
 	{TEGRA_PINGROUP_ATA,   TEGRA_MUX_IDE,           TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_ATB,   TEGRA_MUX_SDIO4,         TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_ATC,   TEGRA_MUX_NAND,          TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
@@ -55,7 +55,6 @@ static __initdata struct tegra_pingroup_config seaboard_pinmux[] = {
 	{TEGRA_PINGROUP_DAP2,  TEGRA_MUX_DAP2,          TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_DAP3,  TEGRA_MUX_DAP3,          TEGRA_PUPD_NORMAL,    TEGRA_TRI_TRISTATE},
 	{TEGRA_PINGROUP_DAP4,  TEGRA_MUX_DAP4,          TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
-	{TEGRA_PINGROUP_DDC,   TEGRA_MUX_RSVD2,         TEGRA_PUPD_NORMAL,    TEGRA_TRI_TRISTATE},
 	{TEGRA_PINGROUP_DTA,   TEGRA_MUX_VI,            TEGRA_PUPD_PULL_DOWN, TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_DTB,   TEGRA_MUX_VI,            TEGRA_PUPD_PULL_DOWN, TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_DTC,   TEGRA_MUX_VI,            TEGRA_PUPD_PULL_DOWN, TEGRA_TRI_NORMAL},
@@ -65,7 +64,6 @@ static __initdata struct tegra_pingroup_config seaboard_pinmux[] = {
 	{TEGRA_PINGROUP_GMA,   TEGRA_MUX_SDIO4,         TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_GMB,   TEGRA_MUX_GMI,           TEGRA_PUPD_PULL_UP,   TEGRA_TRI_TRISTATE},
 	{TEGRA_PINGROUP_GMC,   TEGRA_MUX_UARTD,         TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
-	{TEGRA_PINGROUP_GMD,   TEGRA_MUX_SFLASH,        TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_GME,   TEGRA_MUX_SDIO4,         TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_GPU,   TEGRA_MUX_PWM,           TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_GPU7,  TEGRA_MUX_RTCK,          TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
@@ -108,13 +106,8 @@ static __initdata struct tegra_pingroup_config seaboard_pinmux[] = {
 	{TEGRA_PINGROUP_LM0,   TEGRA_MUX_RSVD4,         TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_LM1,   TEGRA_MUX_CRT,           TEGRA_PUPD_NORMAL,    TEGRA_TRI_TRISTATE},
 	{TEGRA_PINGROUP_LPP,   TEGRA_MUX_DISPLAYA,      TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
-	{TEGRA_PINGROUP_LPW0,  TEGRA_MUX_HDMI,          TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_LPW1,  TEGRA_MUX_RSVD4,         TEGRA_PUPD_NORMAL,    TEGRA_TRI_TRISTATE},
-	{TEGRA_PINGROUP_LPW2,  TEGRA_MUX_HDMI,          TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_LSC0,  TEGRA_MUX_DISPLAYA,      TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
-	{TEGRA_PINGROUP_LSC1,  TEGRA_MUX_HDMI,          TEGRA_PUPD_NORMAL,    TEGRA_TRI_TRISTATE},
-	{TEGRA_PINGROUP_LSCK,  TEGRA_MUX_HDMI,          TEGRA_PUPD_NORMAL,    TEGRA_TRI_TRISTATE},
-	{TEGRA_PINGROUP_LSDA,  TEGRA_MUX_HDMI,          TEGRA_PUPD_NORMAL,    TEGRA_TRI_TRISTATE},
 	{TEGRA_PINGROUP_LSDI,  TEGRA_MUX_RSVD4,         TEGRA_PUPD_NORMAL,    TEGRA_TRI_TRISTATE},
 	{TEGRA_PINGROUP_LSPI,  TEGRA_MUX_DISPLAYA,      TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_LVP0,  TEGRA_MUX_RSVD4,         TEGRA_PUPD_NORMAL,    TEGRA_TRI_TRISTATE},
@@ -122,25 +115,19 @@ static __initdata struct tegra_pingroup_config seaboard_pinmux[] = {
 	{TEGRA_PINGROUP_LVS,   TEGRA_MUX_DISPLAYA,      TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_OWC,   TEGRA_MUX_RSVD2,         TEGRA_PUPD_NORMAL,    TEGRA_TRI_TRISTATE},
 	{TEGRA_PINGROUP_PMC,   TEGRA_MUX_PWR_ON,        TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
-	{TEGRA_PINGROUP_PTA,   TEGRA_MUX_HDMI,          TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_RM,    TEGRA_MUX_I2C,           TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_SDB,   TEGRA_MUX_SDIO3,         TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_SDC,   TEGRA_MUX_SDIO3,         TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_SDD,   TEGRA_MUX_SDIO3,         TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_SDIO1, TEGRA_MUX_SDIO1,         TEGRA_PUPD_PULL_UP,   TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_SLXA,  TEGRA_MUX_PCIE,          TEGRA_PUPD_PULL_UP,   TEGRA_TRI_TRISTATE},
-	{TEGRA_PINGROUP_SLXC,  TEGRA_MUX_SPDIF,         TEGRA_PUPD_NORMAL,    TEGRA_TRI_TRISTATE},
 	{TEGRA_PINGROUP_SLXD,  TEGRA_MUX_SPDIF,         TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
-	{TEGRA_PINGROUP_SLXK,  TEGRA_MUX_PCIE,          TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_SPDI,  TEGRA_MUX_RSVD2,         TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_SPDO,  TEGRA_MUX_RSVD2,         TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
-	{TEGRA_PINGROUP_SPIA,  TEGRA_MUX_GMI,           TEGRA_PUPD_PULL_UP,   TEGRA_TRI_TRISTATE},
 	{TEGRA_PINGROUP_SPIB,  TEGRA_MUX_GMI,           TEGRA_PUPD_NORMAL,    TEGRA_TRI_TRISTATE},
-	{TEGRA_PINGROUP_SPIC,  TEGRA_MUX_GMI,           TEGRA_PUPD_PULL_UP,   TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_SPID,  TEGRA_MUX_SPI1,          TEGRA_PUPD_NORMAL,    TEGRA_TRI_TRISTATE},
 	{TEGRA_PINGROUP_SPIE,  TEGRA_MUX_SPI1,          TEGRA_PUPD_NORMAL,    TEGRA_TRI_TRISTATE},
 	{TEGRA_PINGROUP_SPIF,  TEGRA_MUX_SPI1,          TEGRA_PUPD_PULL_DOWN, TEGRA_TRI_TRISTATE},
-	{TEGRA_PINGROUP_SPIG,  TEGRA_MUX_SPI2_ALT,      TEGRA_PUPD_PULL_UP,   TEGRA_TRI_TRISTATE},
 	{TEGRA_PINGROUP_SPIH,  TEGRA_MUX_SPI2_ALT,      TEGRA_PUPD_PULL_UP,   TEGRA_TRI_TRISTATE},
 	{TEGRA_PINGROUP_UAA,   TEGRA_MUX_ULPI,          TEGRA_PUPD_PULL_UP,   TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_UAB,   TEGRA_MUX_ULPI,          TEGRA_PUPD_PULL_UP,   TEGRA_TRI_NORMAL},
@@ -160,13 +147,24 @@ static __initdata struct tegra_pingroup_config seaboard_pinmux[] = {
 	{TEGRA_PINGROUP_XM2D,  TEGRA_MUX_NONE,          TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
 };
 
-static __initdata struct tegra_pingroup_config ventana_pinmux[] = {
-	{TEGRA_PINGROUP_DAP3, TEGRA_MUX_DAP3,     TEGRA_PUPD_NORMAL,    TEGRA_TRI_TRISTATE},
+static struct tegra_pingroup_config seaboard_pinmux[] = {
+	{TEGRA_PINGROUP_DDC,   TEGRA_MUX_RSVD2,         TEGRA_PUPD_NORMAL,    TEGRA_TRI_TRISTATE},
+	{TEGRA_PINGROUP_GMD,   TEGRA_MUX_SFLASH,        TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
+	{TEGRA_PINGROUP_LPW0,  TEGRA_MUX_HDMI,          TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
+	{TEGRA_PINGROUP_LPW2,  TEGRA_MUX_HDMI,          TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
+	{TEGRA_PINGROUP_LSC1,  TEGRA_MUX_HDMI,          TEGRA_PUPD_NORMAL,    TEGRA_TRI_TRISTATE},
+	{TEGRA_PINGROUP_LSCK,  TEGRA_MUX_HDMI,          TEGRA_PUPD_NORMAL,    TEGRA_TRI_TRISTATE},
+	{TEGRA_PINGROUP_LSDA,  TEGRA_MUX_HDMI,          TEGRA_PUPD_NORMAL,    TEGRA_TRI_TRISTATE},
+	{TEGRA_PINGROUP_PTA,   TEGRA_MUX_HDMI,          TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
+	{TEGRA_PINGROUP_SLXC,  TEGRA_MUX_SPDIF,         TEGRA_PUPD_NORMAL,    TEGRA_TRI_TRISTATE},
+	{TEGRA_PINGROUP_SLXK,  TEGRA_MUX_PCIE,          TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
+	{TEGRA_PINGROUP_SPIA,  TEGRA_MUX_GMI,           TEGRA_PUPD_PULL_UP,   TEGRA_TRI_TRISTATE},
+	{TEGRA_PINGROUP_SPIC,  TEGRA_MUX_GMI,           TEGRA_PUPD_PULL_UP,   TEGRA_TRI_NORMAL},
+	{TEGRA_PINGROUP_SPIG,  TEGRA_MUX_SPI2_ALT,      TEGRA_PUPD_PULL_UP,   TEGRA_TRI_TRISTATE},
+};
+
+static struct tegra_pingroup_config ventana_pinmux[] = {
 	{TEGRA_PINGROUP_DDC,  TEGRA_MUX_RSVD2,    TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
-	{TEGRA_PINGROUP_DTA,  TEGRA_MUX_VI,       TEGRA_PUPD_PULL_DOWN, TEGRA_TRI_NORMAL},
-	{TEGRA_PINGROUP_DTB,  TEGRA_MUX_VI,       TEGRA_PUPD_PULL_DOWN, TEGRA_TRI_NORMAL},
-	{TEGRA_PINGROUP_DTC,  TEGRA_MUX_VI,       TEGRA_PUPD_PULL_DOWN, TEGRA_TRI_NORMAL},
-	{TEGRA_PINGROUP_DTD,  TEGRA_MUX_VI,       TEGRA_PUPD_PULL_DOWN, TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_GMD,  TEGRA_MUX_SFLASH,   TEGRA_PUPD_NORMAL,    TEGRA_TRI_TRISTATE},
 	{TEGRA_PINGROUP_LPW0, TEGRA_MUX_RSVD4,    TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_LPW2, TEGRA_MUX_RSVD4,    TEGRA_PUPD_NORMAL,    TEGRA_TRI_NORMAL},
@@ -181,65 +179,59 @@ static __initdata struct tegra_pingroup_config ventana_pinmux[] = {
 	{TEGRA_PINGROUP_SPIG, TEGRA_MUX_SPI2_ALT, TEGRA_PUPD_NORMAL,    TEGRA_TRI_TRISTATE},
 };
 
-static struct platform_device *pinmux_devices[] = {
-	&tegra_gpio_device,
-	&tegra_pinmux_device,
-};
-
 static struct tegra_gpio_table common_gpio_table[] = {
 	{ .gpio = TEGRA_GPIO_SD2_CD,		.enable = true },
 	{ .gpio = TEGRA_GPIO_SD2_WP,		.enable = true },
 	{ .gpio = TEGRA_GPIO_SD2_POWER,		.enable = true },
+	{ .gpio = TEGRA_GPIO_CDC_IRQ,		.enable = true },
+};
+
+static struct tegra_gpio_table seaboard_gpio_table[] = {
 	{ .gpio = TEGRA_GPIO_LIDSWITCH,		.enable = true },
 	{ .gpio = TEGRA_GPIO_POWERKEY,		.enable = true },
 	{ .gpio = TEGRA_GPIO_HP_DET,		.enable = true },
 	{ .gpio = TEGRA_GPIO_ISL29018_IRQ,	.enable = true },
-	{ .gpio = TEGRA_GPIO_CDC_IRQ,		.enable = true },
 	{ .gpio = TEGRA_GPIO_USB1,		.enable = true },
 };
 
-static void __init update_pinmux(struct tegra_pingroup_config *newtbl, int size)
-{
-	int i, j;
-	struct tegra_pingroup_config *new_pingroup, *base_pingroup;
-
-	/* Update base seaboard pinmux table with secondary board
-	 * specific pinmux table table.
-	 */
-	for (i = 0; i < size; i++) {
-		new_pingroup = &newtbl[i];
-		for (j = 0; j < ARRAY_SIZE(seaboard_pinmux); j++) {
-			base_pingroup = &seaboard_pinmux[j];
-			if (new_pingroup->pingroup == base_pingroup->pingroup) {
-				*base_pingroup = *new_pingroup;
-				break;
-			}
-		}
-	}
-}
-
-void __init seaboard_common_pinmux_init(void)
-{
-	if (!of_machine_is_compatible("nvidia,tegra20"))
-		platform_add_devices(pinmux_devices,
-					ARRAY_SIZE(pinmux_devices));
+static struct tegra_gpio_table ventana_gpio_table[] = {
+	/* hp_det */
+	{ .gpio = TEGRA_GPIO_PW2,		.enable = true },
+	/* int_mic_en */
+	{ .gpio = TEGRA_GPIO_PX0,		.enable = true },
+	/* ext_mic_en */
+	{ .gpio = TEGRA_GPIO_PX1,		.enable = true },
+};
 
-	tegra_pinmux_config_table(seaboard_pinmux, ARRAY_SIZE(seaboard_pinmux));
+static struct tegra_board_pinmux_conf common_conf = {
+	.pgs = common_pinmux,
+	.pg_count = ARRAY_SIZE(common_pinmux),
+	.gpios = common_gpio_table,
+	.gpio_count = ARRAY_SIZE(common_gpio_table),
+};
 
-	tegra_drive_pinmux_config_table(seaboard_drive_pinmux,
-					ARRAY_SIZE(seaboard_drive_pinmux));
+static struct tegra_board_pinmux_conf seaboard_conf = {
+	.pgs = seaboard_pinmux,
+	.pg_count = ARRAY_SIZE(seaboard_pinmux),
+	.drives = seaboard_drive_pinmux,
+	.drive_count = ARRAY_SIZE(seaboard_drive_pinmux),
+	.gpios = seaboard_gpio_table,
+	.gpio_count = ARRAY_SIZE(seaboard_gpio_table),
+};
 
-	tegra_gpio_config(common_gpio_table, ARRAY_SIZE(common_gpio_table));
-}
+static struct tegra_board_pinmux_conf ventana_conf = {
+	.pgs = ventana_pinmux,
+	.pg_count = ARRAY_SIZE(ventana_pinmux),
+	.gpios = ventana_gpio_table,
+	.gpio_count = ARRAY_SIZE(ventana_gpio_table),
+};
 
-void __init seaboard_pinmux_init(void)
+void seaboard_pinmux_init(void)
 {
-	seaboard_common_pinmux_init();
+	tegra_board_pinmux_init(&common_conf, &seaboard_conf);
 }
 
-void __init ventana_pinmux_init(void)
+void ventana_pinmux_init(void)
 {
-	update_pinmux(ventana_pinmux, ARRAY_SIZE(ventana_pinmux));
-	seaboard_common_pinmux_init();
+	tegra_board_pinmux_init(&common_conf, &ventana_conf);
 }
-

arch/arm/mach-tegra/board-trimslice-pinmux.c

@@ -22,10 +22,10 @@
 #include <mach/pinmux-tegra20.h>
 
 #include "gpio-names.h"
+#include "board-pinmux.h"
 #include "board-trimslice.h"
-#include "devices.h"
 
-static __initdata struct tegra_pingroup_config trimslice_pinmux[] = {
+static struct tegra_pingroup_config trimslice_pinmux[] = {
 	{TEGRA_PINGROUP_ATA,   TEGRA_MUX_IDE,           TEGRA_PUPD_NORMAL,	TEGRA_TRI_TRISTATE},
 	{TEGRA_PINGROUP_ATB,   TEGRA_MUX_SDIO4,         TEGRA_PUPD_NORMAL,	TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_ATC,   TEGRA_MUX_NAND,          TEGRA_PUPD_NORMAL,	TEGRA_TRI_TRISTATE},
@@ -106,7 +106,7 @@ static __initdata struct tegra_pingroup_config trimslice_pinmux[] = {
 	{TEGRA_PINGROUP_LVS,   TEGRA_MUX_DISPLAYA,      TEGRA_PUPD_PULL_UP,     TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_OWC,   TEGRA_MUX_RSVD2,         TEGRA_PUPD_PULL_UP,     TEGRA_TRI_TRISTATE},
 	{TEGRA_PINGROUP_PMC,   TEGRA_MUX_PWR_ON,        TEGRA_PUPD_NORMAL,      TEGRA_TRI_TRISTATE},
-	{TEGRA_PINGROUP_PTA,   TEGRA_MUX_RSVD3,         TEGRA_PUPD_NORMAL,      TEGRA_TRI_TRISTATE},
+	{TEGRA_PINGROUP_PTA,   TEGRA_MUX_GMI,           TEGRA_PUPD_NORMAL,      TEGRA_TRI_TRISTATE},
 	{TEGRA_PINGROUP_RM,    TEGRA_MUX_I2C,           TEGRA_PUPD_PULL_UP,     TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_SDB,   TEGRA_MUX_PWM,           TEGRA_PUPD_NORMAL,      TEGRA_TRI_NORMAL},
 	{TEGRA_PINGROUP_SDC,   TEGRA_MUX_PWM,           TEGRA_PUPD_PULL_UP,     TEGRA_TRI_NORMAL},
@@ -144,11 +144,6 @@ static __initdata struct tegra_pingroup_config trimslice_pinmux[] = {
 	{TEGRA_PINGROUP_XM2D,  TEGRA_MUX_NONE,          TEGRA_PUPD_NORMAL,      TEGRA_TRI_NORMAL},
 };
 
-static struct platform_device *pinmux_devices[] = {
-	&tegra_gpio_device,
-	&tegra_pinmux_device,
-};
-
 static struct tegra_gpio_table gpio_table[] = {
 	{ .gpio = TRIMSLICE_GPIO_SD4_CD, .enable = true	}, /* mmc4 cd */
 	{ .gpio = TRIMSLICE_GPIO_SD4_WP, .enable = true	}, /* mmc4 wp */
@@ -157,11 +152,14 @@ static struct tegra_gpio_table gpio_table[] = {
 	{ .gpio = TRIMSLICE_GPIO_USB2_RST,  .enable = true }, /* USB2 PHY rst */
 };
 
-void __init trimslice_pinmux_init(void)
+static struct tegra_board_pinmux_conf conf = {
+	.pgs = trimslice_pinmux,
+	.pg_count = ARRAY_SIZE(trimslice_pinmux),
+	.gpios = gpio_table,
+	.gpio_count = ARRAY_SIZE(gpio_table),
+};
+
+void trimslice_pinmux_init(void)
 {
-	if (!of_machine_is_compatible("nvidia,tegra20"))
-		platform_add_devices(pinmux_devices,
-					ARRAY_SIZE(pinmux_devices));
-	tegra_pinmux_config_table(trimslice_pinmux, ARRAY_SIZE(trimslice_pinmux));
-	tegra_gpio_config(gpio_table, ARRAY_SIZE(gpio_table));
+	tegra_board_pinmux_init(&conf, NULL);
 }

arch/arm/mach-tegra/pcie.c

@@ -37,7 +37,6 @@
 #include <asm/sizes.h>
 #include <asm/mach/pci.h>
 
-#include <mach/pinmux.h>
 #include <mach/iomap.h>
 #include <mach/clk.h>
 #include <mach/powergate.h>

arch/arm/plat-mxc/include/mach/iomux-mx25.h

@@ -265,16 +265,20 @@
 #define MX25_PAD_CSI_D2__CSI_D2		IOMUX_PAD(0x318, 0x120, 0x10, 0, 0, NO_PAD_CTRL)
 #define MX25_PAD_CSI_D2__UART5_RXD_MUX	IOMUX_PAD(0x318, 0x120, 0x11, 0x578, 1, NO_PAD_CTRL)
 #define MX25_PAD_CSI_D2__GPIO_1_27	IOMUX_PAD(0x318, 0x120, 0x15, 0, 0, NO_PAD_CTRL)
+#define MX25_PAD_CSI_D2__CSPI3_MOSI	IOMUX_PAD(0x318, 0x120, 0x17, 0, 0, NO_PAD_CTRL)
 
 #define MX25_PAD_CSI_D3__CSI_D3		IOMUX_PAD(0x31c, 0x124, 0x10, 0, 0, NO_PAD_CTRL)
 #define MX25_PAD_CSI_D3__GPIO_1_28	IOMUX_PAD(0x31c, 0x124, 0x15, 0, 0, NO_PAD_CTRL)
+#define MX25_PAD_CSI_D3__CSPI3_MISO	IOMUX_PAD(0x31c, 0x124, 0x17, 0x4b4, 1, NO_PAD_CTRL)
 
 #define MX25_PAD_CSI_D4__CSI_D4		IOMUX_PAD(0x320, 0x128, 0x10, 0, 0, NO_PAD_CTRL)
 #define MX25_PAD_CSI_D4__UART5_RTS	IOMUX_PAD(0x320, 0x128, 0x11, 0x574, 1, NO_PAD_CTRL)
 #define MX25_PAD_CSI_D4__GPIO_1_29	IOMUX_PAD(0x320, 0x128, 0x15, 0, 0, NO_PAD_CTRL)
+#define MX25_PAD_CSI_D4__CSPI3_SCLK	IOMUX_PAD(0x320, 0x128, 0x17, 0, 0, NO_PAD_CTRL)
 
 #define MX25_PAD_CSI_D5__CSI_D5		IOMUX_PAD(0x324, 0x12c, 0x10, 0, 0, NO_PAD_CTRL)
 #define MX25_PAD_CSI_D5__GPIO_1_30	IOMUX_PAD(0x324, 0x12c, 0x15, 0, 0, NO_PAD_CTRL)
+#define MX25_PAD_CSI_D5__CSPI3_RDY	IOMUX_PAD(0x324, 0x12c, 0x17, 0, 0, NO_PAD_CTRL)
 
 #define MX25_PAD_CSI_D6__CSI_D6		IOMUX_PAD(0x328, 0x130, 0x10, 0, 0, NO_PAD_CTRL)
 #define MX25_PAD_CSI_D6__GPIO_1_31	IOMUX_PAD(0x328, 0x130, 0x15, 0, 0, NO_PAD_CTRL)

arch/arm/plat-omap/include/plat/uncompress.h

@@ -179,6 +179,9 @@ static inline void __arch_decomp_setup(unsigned long arch_id)
 		/* TI8168 base boards using UART3 */
 		DEBUG_LL_TI81XX(3, ti8168evm);
 
+		/* TI8148 base boards using UART1 */
+		DEBUG_LL_TI81XX(1, ti8148evm);
+
 	} while (0);
 }
 

arch/arm/plat-omap/include/plat/usb.h

@@ -114,6 +114,7 @@ extern void am35x_musb_reset(void);
 extern void am35x_musb_phy_power(u8 on);
 extern void am35x_musb_clear_irq(void);
 extern void am35x_set_mode(u8 musb_mode);
+extern void ti81xx_musb_phy_power(u8 on);
 
 /*
  * FIXME correct answer depends on hmc_mode,
@@ -273,6 +274,37 @@ static inline void omap2_usbfs_init(struct omap_usb_config *pdata)
 #define CONF2_OTGPWRDN		(1 << 2)
 #define CONF2_DATPOL		(1 << 1)
 
+/* TI81XX specific definitions */
+#define USBCTRL0	0x620
+#define USBSTAT0	0x624
+
+/* TI816X PHY controls bits */
+#define TI816X_USBPHY0_NORMAL_MODE	(1 << 0)
+#define TI816X_USBPHY_REFCLK_OSC	(1 << 8)
+
+/* TI814X PHY controls bits */
+#define USBPHY_CM_PWRDN		(1 << 0)
+#define USBPHY_OTG_PWRDN	(1 << 1)
+#define USBPHY_CHGDET_DIS	(1 << 2)
+#define USBPHY_CHGDET_RSTRT	(1 << 3)
+#define USBPHY_SRCONDM		(1 << 4)
+#define USBPHY_SINKONDP		(1 << 5)
+#define USBPHY_CHGISINK_EN	(1 << 6)
+#define USBPHY_CHGVSRC_EN	(1 << 7)
+#define USBPHY_DMPULLUP		(1 << 8)
+#define USBPHY_DPPULLUP		(1 << 9)
+#define USBPHY_CDET_EXTCTL	(1 << 10)
+#define USBPHY_GPIO_MODE	(1 << 12)
+#define USBPHY_DPOPBUFCTL	(1 << 13)
+#define USBPHY_DMOPBUFCTL	(1 << 14)
+#define USBPHY_DPINPUT		(1 << 15)
+#define USBPHY_DMINPUT		(1 << 16)
+#define USBPHY_DPGPIO_PD	(1 << 17)
+#define USBPHY_DMGPIO_PD	(1 << 18)
+#define USBPHY_OTGVDET_EN	(1 << 19)
+#define USBPHY_OTGSESSEND_EN	(1 << 20)
+#define USBPHY_DATA_POLARITY	(1 << 23)
+
 #if defined(CONFIG_ARCH_OMAP1) && defined(CONFIG_USB)
 u32 omap1_usb0_init(unsigned nwires, unsigned is_device);
 u32 omap1_usb1_init(unsigned nwires);

arch/arm/plat-samsung/Kconfig

@@ -88,12 +88,20 @@ config S5P_GPIO_DRVSTR
 
 config SAMSUNG_GPIO_EXTRA
 	int "Number of additional GPIO pins"
+	default 128 if SAMSUNG_GPIO_EXTRA128
+	default 64 if SAMSUNG_GPIO_EXTRA64
 	default 0
 	help
 	  Use additional GPIO space in addition to the GPIO's the SOC
 	  provides. This allows expanding the GPIO space for use with
 	  GPIO expanders.
 
+config SAMSUNG_GPIO_EXTRA64
+	bool
+
+config SAMSUNG_GPIO_EXTRA128
+	bool
+
 config S3C_GPIO_SPACE
 	int "Space between gpio banks"
 	default 0