Merge redhat.com:/spare/repo/netdev-2.6/e1000

into redhat.com:/spare/repo/net-drivers-2.6

drivers/net/e1000/e1000.h

@@ -71,6 +71,7 @@
 #include <linux/mii.h>
 #include <linux/ethtool.h>
 #include <linux/if_vlan.h>
+#include <linux/moduleparam.h>
 
 #define BAR_0		0
 #define BAR_1		1
@@ -89,6 +90,12 @@ struct e1000_adapter;
 
 #define E1000_ERR(args...) printk(KERN_ERR "e1000: " args)
 
+#define PFX "e1000: "
+#define DPRINTK(nlevel, klevel, fmt, args...) \
+	(void)((NETIF_MSG_##nlevel & adapter->msg_enable) && \
+	printk(KERN_##klevel PFX "%s: %s: " fmt, adapter->netdev->name, \
+		__FUNCTION__ , ## args))
+
 #define E1000_MAX_INTR 10
 
 /* How many descriptors for TX and RX ? */
@@ -245,5 +252,6 @@ struct e1000_adapter {
 
 
 	uint32_t pci_state[16];
+	int msg_enable;
 };
 #endif /* _E1000_H_ */

drivers/net/e1000/e1000_ethtool.c

@@ -53,7 +53,7 @@ struct e1000_stats {
 
 #define E1000_STAT(m) sizeof(((struct e1000_adapter *)0)->m), \
 		      offsetof(struct e1000_adapter, m)
-static struct e1000_stats e1000_gstrings_stats[] = {
+static const struct e1000_stats e1000_gstrings_stats[] = {
 	{ "rx_packets", E1000_STAT(net_stats.rx_packets) },
 	{ "tx_packets", E1000_STAT(net_stats.tx_packets) },
 	{ "rx_bytes", E1000_STAT(net_stats.rx_bytes) },
@@ -89,20 +89,22 @@ static struct e1000_stats e1000_gstrings_stats[] = {
 	{ "tx_flow_control_xon", E1000_STAT(stats.xontxc) },
 	{ "tx_flow_control_xoff", E1000_STAT(stats.xofftxc) },
 	{ "rx_csum_offload_good", E1000_STAT(hw_csum_good) },
-	{ "rx_csum_offload_errors", E1000_STAT(hw_csum_err) }
+        { "rx_csum_offload_errors", E1000_STAT(hw_csum_err) },
+	{ "rx_long_byte_count", E1000_STAT(stats.gorcl) }
 };
 #define E1000_STATS_LEN	\
 	sizeof(e1000_gstrings_stats) / sizeof(struct e1000_stats)
-static char e1000_gstrings_test[][ETH_GSTRING_LEN] = {
+static const char e1000_gstrings_test[][ETH_GSTRING_LEN] = {
 	"Register test  (offline)", "Eeprom test    (offline)",
 	"Interrupt test (offline)", "Loopback test  (offline)",
 	"Link test   (on/offline)"
 };
 #define E1000_TEST_LEN sizeof(e1000_gstrings_test) / ETH_GSTRING_LEN
 
-static void
-e1000_ethtool_gset(struct e1000_adapter *adapter, struct ethtool_cmd *ecmd)
+static int
+e1000_get_settings(struct net_device *netdev, struct ethtool_cmd *ecmd)
 {
+	struct e1000_adapter *adapter = netdev->priv;
 	struct e1000_hw *hw = &adapter->hw;
 
 	if(hw->media_type == e1000_media_type_copper) {
@@ -169,11 +171,13 @@ e1000_ethtool_gset(struct e1000_adapter *adapter, struct ethtool_cmd *ecmd)
 	}
 
 	ecmd->autoneg = (hw->autoneg ? AUTONEG_ENABLE : AUTONEG_DISABLE);
+	return 0;
 }
 
 static int
-e1000_ethtool_sset(struct e1000_adapter *adapter, struct ethtool_cmd *ecmd)
+e1000_set_settings(struct net_device *netdev, struct ethtool_cmd *ecmd)
 {
+	struct e1000_adapter *adapter = netdev->priv;
 	struct e1000_hw *hw = &adapter->hw;
 
 	if(ecmd->autoneg == AUTONEG_ENABLE) {
@@ -195,42 +199,41 @@ e1000_ethtool_sset(struct e1000_adapter *adapter, struct ethtool_cmd *ecmd)
 	return 0;
 }
 
-static int
-e1000_ethtool_gpause(struct e1000_adapter *adapter,
-                     struct ethtool_pauseparam *epause)
+static void 
+e1000_get_pauseparam(struct net_device *netdev,
+                    struct ethtool_pauseparam *pause)
 {
+	struct e1000_adapter *adapter = netdev->priv;
 	struct e1000_hw *hw = &adapter->hw;
-	
-	epause->autoneg = 
+	pause->autoneg = 
 		(adapter->fc_autoneg ? AUTONEG_ENABLE : AUTONEG_DISABLE);
 	
 	if(hw->fc == e1000_fc_rx_pause)
-		epause->rx_pause = 1;
+		pause->rx_pause = 1;
 	else if(hw->fc == e1000_fc_tx_pause)
-		epause->tx_pause = 1;
+		pause->tx_pause = 1;
 	else if(hw->fc == e1000_fc_full) {
-		epause->rx_pause = 1;
-		epause->tx_pause = 1;
+		pause->rx_pause = 1;
+		pause->tx_pause = 1;
 	}
-	
-	return 0;
 }
 
 static int 
-e1000_ethtool_spause(struct e1000_adapter *adapter,
-                     struct ethtool_pauseparam *epause)
+e1000_set_pauseparam(struct net_device *netdev,
+                    struct ethtool_pauseparam *pause)
 {
+	struct e1000_adapter *adapter = netdev->priv;
 	struct e1000_hw *hw = &adapter->hw;
 	
-	adapter->fc_autoneg = epause->autoneg;
+	adapter->fc_autoneg = pause->autoneg;
 
-	if(epause->rx_pause && epause->tx_pause)
+	if(pause->rx_pause && pause->tx_pause)
 		hw->fc = e1000_fc_full;
-	else if(epause->rx_pause && !epause->tx_pause)
+	else if(pause->rx_pause && !pause->tx_pause)
 		hw->fc = e1000_fc_rx_pause;
-	else if(!epause->rx_pause && epause->tx_pause)
+	else if(!pause->rx_pause && pause->tx_pause)
 		hw->fc = e1000_fc_tx_pause;
-	else if(!epause->rx_pause && !epause->tx_pause)
+	else if(!pause->rx_pause && !pause->tx_pause)
 		hw->fc = e1000_fc_none;
 
 	hw->original_fc = hw->fc;
@@ -248,28 +251,124 @@ e1000_ethtool_spause(struct e1000_adapter *adapter,
 	return 0;
 }
 
+static uint32_t
+e1000_get_rx_csum(struct net_device *netdev)
+{
+	struct e1000_adapter *adapter = netdev->priv;
+	return adapter->rx_csum;
+}
+
+static int
+e1000_set_rx_csum(struct net_device *netdev, uint32_t data)
+{
+	struct e1000_adapter *adapter = netdev->priv;
+	adapter->rx_csum = data;
+
+	if(netif_running(netdev)) {
+		e1000_down(adapter);
+		e1000_up(adapter);
+	} else
+		e1000_reset(adapter);
+	return 0;
+}
+
+static uint32_t
+e1000_get_tx_csum(struct net_device *netdev)
+{
+	return (netdev->features & NETIF_F_HW_CSUM) != 0;
+}
+
+static int
+e1000_set_tx_csum(struct net_device *netdev, uint32_t data)
+{
+	struct e1000_adapter *adapter = netdev->priv;
+
+	if(adapter->hw.mac_type < e1000_82543) {
+		if (!data)
+			return -EINVAL;
+		return 0;
+	}
+
+	if (data)
+		netdev->features |= NETIF_F_HW_CSUM;
+	else
+		netdev->features &= ~NETIF_F_HW_CSUM;
+
+	return 0;
+}
+
+static uint32_t
+e1000_get_sg(struct net_device *netdev)
+{
+	return (netdev->features & NETIF_F_SG) != 0;
+}
+
+static int
+e1000_set_sg(struct net_device *netdev, uint32_t data)
+{
+	if (data)
+		netdev->features |= NETIF_F_SG;
+	else
+		netdev->features &= ~NETIF_F_SG;
+
+	return 0;
+}
+
+#ifdef NETIF_F_TSO
+static uint32_t
+e1000_get_tso(struct net_device *netdev)
+{
+	return (netdev->features & NETIF_F_TSO) != 0;
+} 
+
+static int
+e1000_set_tso(struct net_device *netdev, uint32_t data)
+{
+	struct e1000_adapter *adapter = netdev->priv;
+	if ((adapter->hw.mac_type < e1000_82544) ||
+	    (adapter->hw.mac_type == e1000_82547)) 
+		return data ? -EINVAL : 0;
+
+	if (data)
+		netdev->features |= NETIF_F_TSO;
+	else
+		netdev->features &= ~NETIF_F_TSO;
+	return 0;
+} 
+#endif /* NETIF_F_TSO */
+
+static uint32_t
+e1000_get_msglevel(struct net_device *netdev)
+{
+	struct e1000_adapter *adapter = netdev->priv;
+	return adapter->msg_enable;
+}
+
 static void
-e1000_ethtool_gdrvinfo(struct e1000_adapter *adapter,
-                       struct ethtool_drvinfo *drvinfo)
+e1000_set_msglevel(struct net_device *netdev, uint32_t data)
+{
+	struct e1000_adapter *adapter = netdev->priv;
+	adapter->msg_enable = data;
+}
+
+static int 
+e1000_get_regs_len(struct net_device *netdev)
 {
-	strncpy(drvinfo->driver,  e1000_driver_name, 32);
-	strncpy(drvinfo->version, e1000_driver_version, 32);
-	strncpy(drvinfo->fw_version, "N/A", 32);
-	strncpy(drvinfo->bus_info, pci_name(adapter->pdev), 32);
-	drvinfo->n_stats = E1000_STATS_LEN;
-	drvinfo->testinfo_len = E1000_TEST_LEN;
 #define E1000_REGS_LEN 32
-	drvinfo->regdump_len  = E1000_REGS_LEN * sizeof(uint32_t);
-	drvinfo->eedump_len = adapter->hw.eeprom.word_size * 2;
+	return E1000_REGS_LEN * sizeof(uint32_t);
 }
 
 static void
-e1000_ethtool_gregs(struct e1000_adapter *adapter,
-                    struct ethtool_regs *regs, uint32_t *regs_buff)
+e1000_get_regs(struct net_device *netdev,
+                    struct ethtool_regs *regs, void *p)
 {
+	struct e1000_adapter *adapter = netdev->priv;
 	struct e1000_hw *hw = &adapter->hw;
+	uint32_t *regs_buff = p;
 	uint16_t phy_data;
 
+	memset(p, 0, E1000_REGS_LEN * sizeof(uint32_t));
+
 	regs->version = (1 << 24) | (hw->revision_id << 16) | hw->device_id;
 
 	regs_buff[0]  = E1000_READ_REG(hw, CTRL);
@@ -342,37 +441,39 @@ e1000_ethtool_gregs(struct e1000_adapter *adapter,
 	e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data);
 	regs_buff[24] = (uint32_t)phy_data;  /* phy local receiver status */
 	regs_buff[25] = regs_buff[24];  /* phy remote receiver status */
+}
 
-	return;
+static int
+e1000_get_eeprom_len(struct net_device *netdev)
+{
+	struct e1000_adapter *adapter = netdev->priv;
+	return adapter->hw.eeprom.word_size * 2;
 }
 
 static int
-e1000_ethtool_geeprom(struct e1000_adapter *adapter,
-                      struct ethtool_eeprom *eeprom, uint16_t *eeprom_buff)
+e1000_get_eeprom(struct net_device *netdev,
+                      struct ethtool_eeprom *eeprom, uint8_t *bytes)
 {
+	struct e1000_adapter *adapter = netdev->priv;
 	struct e1000_hw *hw = &adapter->hw;
+	uint16_t *eeprom_buff;
 	int first_word, last_word;
 	int ret_val = 0;
 	uint16_t i;
 
-	if(eeprom->len == 0) {
-		ret_val = -EINVAL;
-		goto geeprom_error;
-	}
+	if(eeprom->len == 0) 
+		return -EINVAL;
 
 	eeprom->magic = hw->vendor_id | (hw->device_id << 16);
 
-	if(eeprom->offset > eeprom->offset + eeprom->len) {
-		ret_val = -EINVAL;
-		goto geeprom_error;
-	}
-
-	if((eeprom->offset + eeprom->len) > (hw->eeprom.word_size * 2))
-		eeprom->len = ((hw->eeprom.word_size * 2) - eeprom->offset);
-
 	first_word = eeprom->offset >> 1;
 	last_word = (eeprom->offset + eeprom->len - 1) >> 1;
 
+	eeprom_buff = kmalloc(sizeof(uint16_t) * 
+			(last_word - first_word + 1), GFP_KERNEL);
+	if (!eeprom_buff)
+		return -ENOMEM;
+
 	if(hw->eeprom.type == e1000_eeprom_spi)
 		ret_val = e1000_read_eeprom(hw, first_word,
 					    last_word - first_word + 1,
@@ -388,14 +489,19 @@ e1000_ethtool_geeprom(struct e1000_adapter *adapter,
 	for (i = 0; i < last_word - first_word + 1; i++)
 		le16_to_cpus(&eeprom_buff[i]);
 
-geeprom_error:
+
+	memcpy(bytes, (uint8_t *)eeprom_buff + (eeprom->offset%2), 
+				eeprom->len);
+	kfree(eeprom_buff);
+
 	return ret_val;
 }
 
 static int
-e1000_ethtool_seeprom(struct e1000_adapter *adapter,
-                      struct ethtool_eeprom *eeprom, void *user_data)
+e1000_set_eeprom(struct net_device *netdev,
+                      struct ethtool_eeprom *eeprom, uint8_t *bytes)
 {
+	struct e1000_adapter *adapter = netdev->priv;
 	struct e1000_hw *hw = &adapter->hw;
 	uint16_t *eeprom_buff;
 	void *ptr;
@@ -410,9 +516,6 @@ e1000_ethtool_seeprom(struct e1000_adapter *adapter,
 
 	max_len = hw->eeprom.word_size * 2;
 
-	if((eeprom->offset + eeprom->len) > max_len)
-		eeprom->len = (max_len - eeprom->offset);
-
 	first_word = eeprom->offset >> 1;
 	last_word = (eeprom->offset + eeprom->len - 1) >> 1;
 	eeprom_buff = kmalloc(max_len, GFP_KERNEL);
@@ -439,11 +542,7 @@ e1000_ethtool_seeprom(struct e1000_adapter *adapter,
 	for (i = 0; i < last_word - first_word + 1; i++)
 		le16_to_cpus(&eeprom_buff[i]);
 
-	if((ret_val != 0) || copy_from_user(ptr, user_data, eeprom->len)) {
-		ret_val = -EFAULT;
-		goto seeprom_error;
-	}
-
+	memcpy(ptr, bytes, eeprom->len);
 	for (i = 0; i < last_word - first_word + 1; i++)
 		eeprom_buff[i] = cpu_to_le16(eeprom_buff[i]);
 
@@ -454,15 +553,31 @@ e1000_ethtool_seeprom(struct e1000_adapter *adapter,
 	if((ret_val == 0) && first_word <= EEPROM_CHECKSUM_REG)
 		e1000_update_eeprom_checksum(hw);
 
-seeprom_error:
 	kfree(eeprom_buff);
 	return ret_val;
 }
 
-static int
-e1000_ethtool_gring(struct e1000_adapter *adapter,
+static void
+e1000_get_drvinfo(struct net_device *netdev,
+                       struct ethtool_drvinfo *drvinfo)
+{
+	struct e1000_adapter *adapter = netdev->priv;
+
+	strncpy(drvinfo->driver,  e1000_driver_name, 32);
+	strncpy(drvinfo->version, e1000_driver_version, 32);
+	strncpy(drvinfo->fw_version, "N/A", 32);
+	strncpy(drvinfo->bus_info, pci_name(adapter->pdev), 32);
+	drvinfo->n_stats = E1000_STATS_LEN;
+	drvinfo->testinfo_len = E1000_TEST_LEN;
+	drvinfo->regdump_len = e1000_get_regs_len(netdev);
+	drvinfo->eedump_len = e1000_get_eeprom_len(netdev);
+}
+
+static void
+e1000_get_ringparam(struct net_device *netdev,
                     struct ethtool_ringparam *ring)
 {
+	struct e1000_adapter *adapter = netdev->priv;
 	e1000_mac_type mac_type = adapter->hw.mac_type;
 	struct e1000_desc_ring *txdr = &adapter->tx_ring;
 	struct e1000_desc_ring *rxdr = &adapter->rx_ring;
@@ -477,14 +592,14 @@ e1000_ethtool_gring(struct e1000_adapter *adapter,
 	ring->tx_pending = txdr->count;
 	ring->rx_mini_pending = 0;
 	ring->rx_jumbo_pending = 0;
-
-	return 0;
 }
+
 static int 
-e1000_ethtool_sring(struct e1000_adapter *adapter,
+e1000_set_ringparam(struct net_device *netdev,
                     struct ethtool_ringparam *ring)
 {
 	int err;
+	struct e1000_adapter *adapter = netdev->priv;
 	e1000_mac_type mac_type = adapter->hw.mac_type;
 	struct e1000_desc_ring *txdr = &adapter->tx_ring;
 	struct e1000_desc_ring *rxdr = &adapter->rx_ring;
@@ -538,6 +653,7 @@ e1000_ethtool_sring(struct e1000_adapter *adapter,
 	return err;
 }
 
+
 #define REG_PATTERN_TEST(R, M, W)                                              \
 {                                                                              \
 	uint32_t pat, value;                                                   \
@@ -628,6 +744,7 @@ e1000_reg_test(struct e1000_adapter *adapter, uint64_t *data)
 	for(i = 0; i < E1000_MC_TBL_SIZE; i++)
 		REG_PATTERN_TEST(MTA + (i << 2), 0xFFFFFFFF, 0xFFFFFFFF);
 
+	*data = 0;
 	return 0;
 }
 
@@ -939,8 +1056,6 @@ e1000_phy_disable_receiver(struct e1000_adapter *adapter)
 	e1000_write_phy_reg(&adapter->hw, 30, 0x8FFC);
 	e1000_write_phy_reg(&adapter->hw, 29, 0x001A);
 	e1000_write_phy_reg(&adapter->hw, 30, 0x8FF0);
-
-	return;
 }
 
 static void
@@ -1219,7 +1334,7 @@ e1000_run_loopback_test(struct e1000_adapter *adapter)
 
 	for(i = 0; i < 64; i++) {
 		e1000_create_lbtest_frame(txdr->buffer_info[i].skb, 1024);
-		pci_dma_sync_single_for_device(pdev, txdr->buffer_info[i].dma,
+		pci_dma_sync_single(pdev, txdr->buffer_info[i].dma,
 				    txdr->buffer_info[i].length,
 				    PCI_DMA_TODEVICE);
 	}
@@ -1227,7 +1342,7 @@ e1000_run_loopback_test(struct e1000_adapter *adapter)
 
 	msec_delay(200);
 
-	pci_dma_sync_single_for_cpu(pdev, rxdr->buffer_info[0].dma,
+	pci_dma_sync_single(pdev, rxdr->buffer_info[0].dma,
 			    rxdr->buffer_info[0].length, PCI_DMA_FROMDEVICE);
 
 	return e1000_check_lbtest_frame(rxdr->buffer_info[0].skb, 1024);
@@ -1258,14 +1373,26 @@ e1000_link_test(struct e1000_adapter *adapter, uint64_t *data)
 }
 
 static int 
-e1000_ethtool_test(struct e1000_adapter *adapter,
+e1000_diag_test_count(struct net_device *netdev)
+{
+	return E1000_TEST_LEN;
+}
+
+static void
+e1000_diag_test(struct net_device *netdev, 
 		   struct ethtool_test *eth_test, uint64_t *data)
 {
-	boolean_t if_running = netif_running(adapter->netdev);
+	struct e1000_adapter *adapter = netdev->priv;
+	boolean_t if_running = netif_running(netdev);
 
 	if(eth_test->flags == ETH_TEST_FL_OFFLINE) {
 		/* Offline tests */
 
+		/* save speed, duplex, autoneg settings */
+		uint16_t autoneg_advertised = adapter->hw.autoneg_advertised;
+    		uint8_t forced_speed_duplex = adapter->hw.forced_speed_duplex;
+		uint8_t autoneg = adapter->hw.autoneg;
+
 		/* Link test performed before hardware reset so autoneg doesn't
 		 * interfere with test result */
 		if(e1000_link_test(adapter, &data[4]))
@@ -1291,6 +1418,10 @@ e1000_ethtool_test(struct e1000_adapter *adapter,
 		if(e1000_loopback_test(adapter, &data[3]))
 			eth_test->flags |= ETH_TEST_FL_FAILED;
 
+		/* restore Autoneg/speed/duplex settings */
+		adapter->hw.autoneg_advertised = autoneg_advertised;
+    		adapter->hw.forced_speed_duplex = forced_speed_duplex;
+    		adapter->hw.autoneg = autoneg;
 		e1000_reset(adapter);
 		if(if_running)
 			e1000_up(adapter);
@@ -1305,12 +1436,12 @@ e1000_ethtool_test(struct e1000_adapter *adapter,
 		data[2] = 0;
 		data[3] = 0;
 	}
-	return 0;
 }
 
 static void
-e1000_ethtool_gwol(struct e1000_adapter *adapter, struct ethtool_wolinfo *wol)
+e1000_get_wol(struct net_device *netdev, struct ethtool_wolinfo *wol)
 {
+	struct e1000_adapter *adapter = netdev->priv;
 	struct e1000_hw *hw = &adapter->hw;
 
 	switch(adapter->hw.device_id) {
@@ -1350,8 +1481,9 @@ e1000_ethtool_gwol(struct e1000_adapter *adapter, struct ethtool_wolinfo *wol)
 }
 
 static int
-e1000_ethtool_swol(struct e1000_adapter *adapter, struct ethtool_wolinfo *wol)
+e1000_set_wol(struct net_device *netdev, struct ethtool_wolinfo *wol)
 {
+	struct e1000_adapter *adapter = netdev->priv;
 	struct e1000_hw *hw = &adapter->hw;
 
 	switch(adapter->hw.device_id) {
@@ -1387,7 +1519,6 @@ e1000_ethtool_swol(struct e1000_adapter *adapter, struct ethtool_wolinfo *wol)
 	return 0;
 }
 
-
 /* toggle LED 4 times per second = 2 "blinks" per second */
 #define E1000_ID_INTERVAL	(HZ/4)
 
@@ -1408,8 +1539,13 @@ e1000_led_blink_callback(unsigned long data)
 }
 
 static int
-e1000_ethtool_led_blink(struct e1000_adapter *adapter, struct ethtool_value *id)
+e1000_phys_id(struct net_device *netdev, uint32_t data)
 {
+	struct e1000_adapter *adapter = netdev->priv;
+
+	if(!data || data > (uint32_t)(MAX_SCHEDULE_TIMEOUT / HZ))
+		data = (uint32_t)(MAX_SCHEDULE_TIMEOUT / HZ);
+
 	if(!adapter->blink_timer.function) {
 		init_timer(&adapter->blink_timer);
 		adapter->blink_timer.function = e1000_led_blink_callback;
@@ -1420,11 +1556,8 @@ e1000_ethtool_led_blink(struct e1000_adapter *adapter, struct ethtool_value *id)
 	mod_timer(&adapter->blink_timer, jiffies);
 
 	set_current_state(TASK_INTERRUPTIBLE);
-	if(id->data)
-		schedule_timeout(id->data * HZ);
-	else
-		schedule_timeout(MAX_SCHEDULE_TIMEOUT);
 
+	schedule_timeout(data * HZ);
 	del_timer_sync(&adapter->blink_timer);
 	e1000_led_off(&adapter->hw);
 	clear_bit(E1000_LED_ON, &adapter->led_status);
@@ -1433,345 +1566,102 @@ e1000_ethtool_led_blink(struct e1000_adapter *adapter, struct ethtool_value *id)
 	return 0;
 }
 
-int
-e1000_ethtool_ioctl(struct net_device *netdev, struct ifreq *ifr)
+static int
+e1000_nway_reset(struct net_device *netdev)
 {
 	struct e1000_adapter *adapter = netdev->priv;
-	void *addr = ifr->ifr_data;
-	uint32_t cmd;
-
-	if(get_user(cmd, (uint32_t *) addr))
-		return -EFAULT;
-
-	switch(cmd) {
-	case ETHTOOL_GSET: {
-		struct ethtool_cmd ecmd = {ETHTOOL_GSET};
-		e1000_ethtool_gset(adapter, &ecmd);
-		if(copy_to_user(addr, &ecmd, sizeof(ecmd)))
-			return -EFAULT;
-		return 0;
-	}
-	case ETHTOOL_SSET: {
-		struct ethtool_cmd ecmd;
-		if(copy_from_user(&ecmd, addr, sizeof(ecmd)))
-			return -EFAULT;
-		return e1000_ethtool_sset(adapter, &ecmd);
-	}
-	case ETHTOOL_GDRVINFO: {
-		struct ethtool_drvinfo drvinfo = {ETHTOOL_GDRVINFO};
-		e1000_ethtool_gdrvinfo(adapter, &drvinfo);
-		if(copy_to_user(addr, &drvinfo, sizeof(drvinfo)))
-			return -EFAULT;
-		return 0;
-	}
-	case ETHTOOL_GSTRINGS: {
-		struct ethtool_gstrings gstrings = { ETHTOOL_GSTRINGS };
-		char *strings = NULL;
-		int err = 0;
-
-		if(copy_from_user(&gstrings, addr, sizeof(gstrings)))
-			return -EFAULT;
-		switch(gstrings.string_set) {
-		case ETH_SS_TEST:
-			gstrings.len = E1000_TEST_LEN;
-			strings = kmalloc(E1000_TEST_LEN * ETH_GSTRING_LEN,
-					  GFP_KERNEL);
-			if(!strings)
-				return -ENOMEM;
-			memcpy(strings, e1000_gstrings_test, E1000_TEST_LEN *
-			       ETH_GSTRING_LEN);
-			break;
-		case ETH_SS_STATS: {
-			int i;
-			gstrings.len = E1000_STATS_LEN;
-			strings = kmalloc(E1000_STATS_LEN * ETH_GSTRING_LEN,
-					  GFP_KERNEL);
-			if(!strings)
-				return -ENOMEM;
-			for(i=0; i < E1000_STATS_LEN; i++) {
-				memcpy(&strings[i * ETH_GSTRING_LEN],
-				       e1000_gstrings_stats[i].stat_string,
-				       ETH_GSTRING_LEN);
-			}
-			break;
-		}
-		default:
-			return -EOPNOTSUPP;
-		}
-		if(copy_to_user(addr, &gstrings, sizeof(gstrings)))
-			err = -EFAULT;
-		addr += offsetof(struct ethtool_gstrings, data);
-		if(!err && copy_to_user(addr, strings,
-		   gstrings.len * ETH_GSTRING_LEN))
-			err = -EFAULT;
-
-		kfree(strings);
-		return err;
-	}
-	case ETHTOOL_GREGS: {
-		struct ethtool_regs regs = {ETHTOOL_GREGS};
-		uint32_t regs_buff[E1000_REGS_LEN];
-
-		if(copy_from_user(&regs, addr, sizeof(regs)))
-			return -EFAULT;
-		memset(regs_buff, 0, sizeof(regs_buff));
-		if (regs.len > E1000_REGS_LEN)
-			regs.len = E1000_REGS_LEN;
-		e1000_ethtool_gregs(adapter, &regs, regs_buff);
-		if(copy_to_user(addr, &regs, sizeof(regs)))
-			return -EFAULT;
-
-		addr += offsetof(struct ethtool_regs, data);
-		if(copy_to_user(addr, regs_buff, regs.len))
-			return -EFAULT;
-
-		return 0;
-	}
-	case ETHTOOL_NWAY_RST: {
 	if(netif_running(netdev)) {
 		e1000_down(adapter);
 		e1000_up(adapter);
 	}
 	return 0;
-	}
-	case ETHTOOL_PHYS_ID: {
-		struct ethtool_value id;
-		if(copy_from_user(&id, addr, sizeof(id)))
-			return -EFAULT;
-		return e1000_ethtool_led_blink(adapter, &id);
-	}
-	case ETHTOOL_GLINK: {
-		struct ethtool_value link = {ETHTOOL_GLINK};
-		link.data = netif_carrier_ok(netdev);
-		if(copy_to_user(addr, &link, sizeof(link)))
-			return -EFAULT;
-		return 0;
-	}
-	case ETHTOOL_GWOL: {
-		struct ethtool_wolinfo wol = {ETHTOOL_GWOL};
-		e1000_ethtool_gwol(adapter, &wol);
-		if(copy_to_user(addr, &wol, sizeof(wol)) != 0)
-			return -EFAULT;
-		return 0;
-	}
-	case ETHTOOL_SWOL: {
-		struct ethtool_wolinfo wol;
-		if(copy_from_user(&wol, addr, sizeof(wol)) != 0)
-			return -EFAULT;
-		return e1000_ethtool_swol(adapter, &wol);
-	}
-	case ETHTOOL_GEEPROM: {
-		struct ethtool_eeprom eeprom = {ETHTOOL_GEEPROM};
-		struct e1000_hw *hw = &adapter->hw;
-		uint16_t *eeprom_buff;
-		void *ptr;
-		int err = 0;
-
-		if(copy_from_user(&eeprom, addr, sizeof(eeprom)))
-			return -EFAULT;
-
-		eeprom_buff = kmalloc(hw->eeprom.word_size * 2, GFP_KERNEL);
-
-		if(!eeprom_buff)
-			return -ENOMEM;
-
-		if((err = e1000_ethtool_geeprom(adapter, &eeprom,
-						eeprom_buff)))
-			goto err_geeprom_ioctl;
-
-		if(copy_to_user(addr, &eeprom, sizeof(eeprom))) {
-			err = -EFAULT;
-			goto err_geeprom_ioctl;
-		}
-
-		addr += offsetof(struct ethtool_eeprom, data);
-		ptr = ((void *)eeprom_buff) + (eeprom.offset & 1);
-
-		if(copy_to_user(addr, ptr, eeprom.len))
-			err = -EFAULT;
+}
 
-err_geeprom_ioctl:
-		kfree(eeprom_buff);
-		return err;
-	}
-	case ETHTOOL_SEEPROM: {
-		struct ethtool_eeprom eeprom;
+static uint32_t
+e1000_get_link(struct net_device *netdev)
+{
+	return netif_carrier_ok(netdev);
+}
 
-		if(copy_from_user(&eeprom, addr, sizeof(eeprom)))
-			return -EFAULT;
+static int 
+e1000_get_stats_count(struct net_device *netdev)
+{
+	return E1000_STATS_LEN;
+}
 
-		addr += offsetof(struct ethtool_eeprom, data);
-		return e1000_ethtool_seeprom(adapter, &eeprom, addr);
-	}
-	case ETHTOOL_GRINGPARAM: {
-		struct ethtool_ringparam ering = {ETHTOOL_GRINGPARAM};
-		e1000_ethtool_gring(adapter, &ering);
-		if(copy_to_user(addr, &ering, sizeof(ering)))
-			return -EFAULT;
-		return 0;
-	}
-	case ETHTOOL_SRINGPARAM: {
-		struct ethtool_ringparam ering;
-		if(copy_from_user(&ering, addr, sizeof(ering)))
-			return -EFAULT;
-		return e1000_ethtool_sring(adapter, &ering);
-	}
-	case ETHTOOL_GPAUSEPARAM: {
-		struct ethtool_pauseparam epause = {ETHTOOL_GPAUSEPARAM};
-		e1000_ethtool_gpause(adapter, &epause);
-		if(copy_to_user(addr, &epause, sizeof(epause)))
-			return -EFAULT;
-		return 0;
-	}
-	case ETHTOOL_SPAUSEPARAM: {
-		struct ethtool_pauseparam epause;
-		if(copy_from_user(&epause, addr, sizeof(epause)))
-			return -EFAULT;
-		return e1000_ethtool_spause(adapter, &epause);
-	}
-	case ETHTOOL_GSTATS: {
-		struct {
-			struct ethtool_stats eth_stats;
-			uint64_t data[E1000_STATS_LEN];
-		} stats = { {ETHTOOL_GSTATS, E1000_STATS_LEN} };
+static void 
+e1000_get_ethtool_stats(struct net_device *netdev, 
+		struct ethtool_stats *stats, uint64_t *data)
+{
+	struct e1000_adapter *adapter = netdev->priv;
 	int i;
 
 	e1000_update_stats(adapter);
-		for(i = 0; i < E1000_STATS_LEN; i++)
-			stats.data[i] = (e1000_gstrings_stats[i].sizeof_stat ==
-					sizeof(uint64_t)) ?
-				*(uint64_t *)((char *)adapter +
-					e1000_gstrings_stats[i].stat_offset) :
-				*(uint32_t *)((char *)adapter +
-					e1000_gstrings_stats[i].stat_offset);
-		if(copy_to_user(addr, &stats, sizeof(stats)))
-			return -EFAULT;
-		return 0;
-	}
-	case ETHTOOL_TEST: {
-		struct {
-			struct ethtool_test eth_test;
-			uint64_t data[E1000_TEST_LEN];
-		} test = { {ETHTOOL_TEST} };
-		int err;
-
-		if(copy_from_user(&test.eth_test, addr, sizeof(test.eth_test)))
-			return -EFAULT;
-
-		test.eth_test.len = E1000_TEST_LEN;
-
-		if((err = e1000_ethtool_test(adapter, &test.eth_test,
-					     test.data)))
-			return err;
-
-		if(copy_to_user(addr, &test, sizeof(test)) != 0)
-			return -EFAULT;
-		return 0;
-	}
-	case ETHTOOL_GRXCSUM: {
-		struct ethtool_value edata = { ETHTOOL_GRXCSUM };
-
-		edata.data = adapter->rx_csum;
-		if (copy_to_user(addr, &edata, sizeof(edata)))
-			return -EFAULT;
-		return 0;
-	}
-	case ETHTOOL_SRXCSUM: {
-		struct ethtool_value edata;
-
-		if (copy_from_user(&edata, addr, sizeof(edata)))
-			return -EFAULT;
-		adapter->rx_csum = edata.data;
-		if(netif_running(netdev)) {
-			e1000_down(adapter);
-			e1000_up(adapter);
-		} else
-			e1000_reset(adapter);
-		return 0;
-	}
-	case ETHTOOL_GTXCSUM: {
-		struct ethtool_value edata = { ETHTOOL_GTXCSUM };
-
-		edata.data =
-			(netdev->features & NETIF_F_HW_CSUM) != 0;
-		if (copy_to_user(addr, &edata, sizeof(edata)))
-			return -EFAULT;
-		return 0;
-	}
-	case ETHTOOL_STXCSUM: {
-		struct ethtool_value edata;
-
-		if (copy_from_user(&edata, addr, sizeof(edata)))
-			return -EFAULT;
-
-		if(adapter->hw.mac_type < e1000_82543) {
-			if (edata.data != 0)
-				return -EINVAL;
-			return 0;
+	for(i = 0; i < E1000_STATS_LEN; i++) {
+		char *p = (char *)adapter+e1000_gstrings_stats[i].stat_offset;	
+		data[i] = (e1000_gstrings_stats[i].sizeof_stat == sizeof(uint64_t)) 
+			? *(uint64_t *)p : *(uint32_t *)p;
 	}
+}
 
-		if (edata.data)
-			netdev->features |= NETIF_F_HW_CSUM;
-		else
-			netdev->features &= ~NETIF_F_HW_CSUM;
+static void 
+e1000_get_strings(struct net_device *netdev, uint32_t stringset, uint8_t *data)
+{
+	int i;
 
-		return 0;
+	switch(stringset) {
+	case ETH_SS_TEST:
+		memcpy(data, *e1000_gstrings_test, 
+			E1000_TEST_LEN*ETH_GSTRING_LEN);
+		break;
+	case ETH_SS_STATS:
+		for (i=0; i < E1000_STATS_LEN; i++) {
+			memcpy(data + i * ETH_GSTRING_LEN, 
+			e1000_gstrings_stats[i].stat_string,
+			ETH_GSTRING_LEN);
 		}
-	case ETHTOOL_GSG: {
-		struct ethtool_value edata = { ETHTOOL_GSG };
-
-		edata.data =
-			(netdev->features & NETIF_F_SG) != 0;
-		if (copy_to_user(addr, &edata, sizeof(edata)))
-			return -EFAULT;
-		return 0;
+		break;
 	}
-	case ETHTOOL_SSG: {
-		struct ethtool_value edata;
-
-		if (copy_from_user(&edata, addr, sizeof(edata)))
-			return -EFAULT;
-
-		if (edata.data)
-			netdev->features |= NETIF_F_SG;
-		else
-			netdev->features &= ~NETIF_F_SG;
+}
 
-		return 0;
-	}
+struct ethtool_ops e1000_ethtool_ops = {
+	.get_settings           = e1000_get_settings,
+	.set_settings           = e1000_set_settings,
+	.get_drvinfo            = e1000_get_drvinfo,
+	.get_regs_len           = e1000_get_regs_len,
+	.get_regs               = e1000_get_regs,
+	.get_wol                = e1000_get_wol,
+	.set_wol                = e1000_set_wol,
+	.get_msglevel	        = e1000_get_msglevel,
+	.set_msglevel	        = e1000_set_msglevel,
+	.nway_reset             = e1000_nway_reset,
+	.get_link               = e1000_get_link,
+	.get_eeprom_len         = e1000_get_eeprom_len,
+	.get_eeprom             = e1000_get_eeprom,
+	.set_eeprom             = e1000_set_eeprom,
+	.get_ringparam          = e1000_get_ringparam,
+	.set_ringparam          = e1000_set_ringparam,
+	.get_pauseparam		= e1000_get_pauseparam,
+	.set_pauseparam		= e1000_set_pauseparam,
+	.get_rx_csum		= e1000_get_rx_csum,
+	.set_rx_csum		= e1000_set_rx_csum,
+	.get_tx_csum		= e1000_get_tx_csum,
+	.set_tx_csum		= e1000_set_tx_csum,
+	.get_sg			= e1000_get_sg,
+	.set_sg			= e1000_set_sg,
 #ifdef NETIF_F_TSO
-	case ETHTOOL_GTSO: {
-		struct ethtool_value edata = { ETHTOOL_GTSO };
-
-		edata.data = (netdev->features & NETIF_F_TSO) != 0;
-		if (copy_to_user(addr, &edata, sizeof(edata)))
-			return -EFAULT;
-		return 0;
-	}
-	case ETHTOOL_STSO: {
-		struct ethtool_value edata;
-
-		if (copy_from_user(&edata, addr, sizeof(edata)))
-			return -EFAULT;
-
-		if ((adapter->hw.mac_type < e1000_82544) ||
-		    (adapter->hw.mac_type == e1000_82547)) {
-			if (edata.data != 0)
-				return -EINVAL;
-			return 0;
-		}
-
-		if (edata.data)
-			netdev->features |= NETIF_F_TSO;
-		else
-			netdev->features &= ~NETIF_F_TSO;
-
-		return 0;
-	}
+	.get_tso		= e1000_get_tso,
+	.set_tso		= e1000_set_tso,
 #endif
-	default:
-		return -EOPNOTSUPP;
-	}
-}
-
+	.self_test_count        = e1000_diag_test_count,
+	.self_test              = e1000_diag_test,
+	.get_strings            = e1000_get_strings,
+	.phys_id                = e1000_phys_id,
+	.get_stats_count        = e1000_get_stats_count,
+	.get_ethtool_stats      = e1000_get_ethtool_stats,
+};
 
+void set_ethtool_ops(struct net_device *netdev)
+{
+	SET_ETHTOOL_OPS(netdev, &e1000_ethtool_ops);
+}

drivers/net/e1000/e1000_hw.c

@@ -470,7 +470,6 @@ e1000_init_hw(struct e1000_hw *hw)
     uint16_t pcix_stat_hi_word;
     uint16_t cmd_mmrbc;
     uint16_t stat_mmrbc;
-
     DEBUGFUNC("e1000_init_hw");
 
     /* Initialize Identification LED */
@@ -910,6 +909,12 @@ e1000_setup_copper_link(struct e1000_hw *hw)
     if(ret_val)
         return ret_val;
 
+    if(hw->mac_type == e1000_82545_rev_3) {
+        ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+        phy_data |= 0x00000008;
+        ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+    }
+
     if(hw->mac_type <= e1000_82543 ||
        hw->mac_type == e1000_82541 || hw->mac_type == e1000_82547 ||
        hw->mac_type == e1000_82541_rev_2 || hw->mac_type == e1000_82547_rev_2)
@@ -1961,7 +1966,7 @@ e1000_config_fc_after_link_up(struct e1000_hw *hw)
 int32_t
 e1000_check_for_link(struct e1000_hw *hw)
 {
-    uint32_t rxcw;
+    uint32_t rxcw = 0;
     uint32_t ctrl;
     uint32_t status;
     uint32_t rctl;
@@ -1971,17 +1976,24 @@ e1000_check_for_link(struct e1000_hw *hw)
 
     DEBUGFUNC("e1000_check_for_link");
 
+    ctrl = E1000_READ_REG(hw, CTRL);
+    status = E1000_READ_REG(hw, STATUS);
+
     /* On adapters with a MAC newer than 82544, SW Defineable pin 1 will be
      * set when the optics detect a signal. On older adapters, it will be
      * cleared when there is a signal.  This applies to fiber media only.
      */
-    if(hw->media_type == e1000_media_type_fiber)
-        signal = (hw->mac_type > e1000_82544) ? E1000_CTRL_SWDPIN1 : 0;
-
-    ctrl = E1000_READ_REG(hw, CTRL);
-    status = E1000_READ_REG(hw, STATUS);
+    if((hw->media_type == e1000_media_type_fiber) ||
+       (hw->media_type == e1000_media_type_internal_serdes)) {
         rxcw = E1000_READ_REG(hw, RXCW);
 
+        if(hw->media_type == e1000_media_type_fiber) {
+            signal = (hw->mac_type > e1000_82544) ? E1000_CTRL_SWDPIN1 : 0;
+            if(status & E1000_STATUS_LU)
+                hw->get_link_status = FALSE;
+        }
+    }
+
     /* If we have a copper PHY then we only want to go out to the PHY
      * registers to see if Auto-Neg has completed and/or if our link
      * status has changed.  The get_link_status flag will be set if we
@@ -2125,8 +2137,7 @@ e1000_check_for_link(struct e1000_hw *hw)
      */
     else if(((hw->media_type == e1000_media_type_fiber) ||
              (hw->media_type == e1000_media_type_internal_serdes)) &&
-              (ctrl & E1000_CTRL_SLU) &&
-              (rxcw & E1000_RXCW_C)) {
+            (ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) {
         DEBUGOUT("RXing /C/, enable AutoNeg and stop forcing link.\r\n");
         E1000_WRITE_REG(hw, TXCW, hw->txcw);
         E1000_WRITE_REG(hw, CTRL, (ctrl & ~E1000_CTRL_SLU));

drivers/net/e1000/e1000_hw.h

@@ -2019,7 +2019,7 @@ struct e1000_hw {
 #define IGP01E1000_PSSR_MDIX_SHIFT             0x000B /* shift right 11 */
 
 /* IGP01E1000 Specific Port Control Register - R/W */
-#define IGP01E1000_PSCR_TP_LOOPBACK            0x0001
+#define IGP01E1000_PSCR_TP_LOOPBACK            0x0010
 #define IGP01E1000_PSCR_CORRECT_NC_SCMBLR      0x0200
 #define IGP01E1000_PSCR_TEN_CRS_SELECT         0x0400
 #define IGP01E1000_PSCR_FLIP_CHIP              0x0800
@@ -2029,16 +2029,18 @@ struct e1000_hw {
 /* IGP01E1000 Specific Port Link Health Register */
 #define IGP01E1000_PLHR_SS_DOWNGRADE           0x8000
 #define IGP01E1000_PLHR_GIG_SCRAMBLER_ERROR    0x4000
+#define IGP01E1000_PLHR_MASTER_FAULT           0x2000
+#define IGP01E1000_PLHR_MASTER_RESOLUTION      0x1000
 #define IGP01E1000_PLHR_GIG_REM_RCVR_NOK       0x0800 /* LH */
 #define IGP01E1000_PLHR_IDLE_ERROR_CNT_OFLOW   0x0400 /* LH */
 #define IGP01E1000_PLHR_DATA_ERR_1             0x0200 /* LH */
 #define IGP01E1000_PLHR_DATA_ERR_0             0x0100
-#define IGP01E1000_PLHR_AUTONEG_FAULT          0x0010
-#define IGP01E1000_PLHR_AUTONEG_ACTIVE         0x0008
-#define IGP01E1000_PLHR_VALID_CHANNEL_D        0x0004
-#define IGP01E1000_PLHR_VALID_CHANNEL_C        0x0002
-#define IGP01E1000_PLHR_VALID_CHANNEL_B        0x0001
-#define IGP01E1000_PLHR_VALID_CHANNEL_A        0x0000
+#define IGP01E1000_PLHR_AUTONEG_FAULT          0x0040
+#define IGP01E1000_PLHR_AUTONEG_ACTIVE         0x0010
+#define IGP01E1000_PLHR_VALID_CHANNEL_D        0x0008
+#define IGP01E1000_PLHR_VALID_CHANNEL_C        0x0004
+#define IGP01E1000_PLHR_VALID_CHANNEL_B        0x0002
+#define IGP01E1000_PLHR_VALID_CHANNEL_A        0x0001
 
 /* IGP01E1000 Channel Quality Register */
 #define IGP01E1000_MSE_CHANNEL_D        0x000F

drivers/net/e1000/e1000_main.c

@@ -27,55 +27,32 @@
 *******************************************************************************/
 
 #include "e1000.h"
+#include <linux/rtnetlink.h>
 
 /* Change Log
  *
+ * 5.2.51   5/14/04
+ *   o set default configuration to 'NAPI disabled'. NAPI enabled driver
+ *     causes kernel panic when the interface is shutdown while data is being
+ *     transferred.
+ * 5.2.47   5/04/04
+ *   o fixed ethtool -t implementation
+ * 5.2.45   4/29/04
+ *   o fixed ethtool -e implementation
+ *   o Support for ethtool ops [Stephen Hemminger (shemminger@osdl.org)]
+ * 5.2.42   4/26/04
+ *   o Added support for the DPRINTK macro for enhanced error logging.  Some
+ *     parts of the patch were supplied by Jon Mason.
+ *   o Move the register_netdevice() donw in the probe routine due to a 
+ *     loading/unloading test issue.
+ *   o Added a long RX byte count the the extra ethtool data members for BER
+ *     testing purposes.
  * 5.2.39	3/12/04
- *   o Added support to read/write eeprom data in proper order.
- *     By default device eeprom is always little-endian, word
- *     addressable 
- *   o Disable TSO as the default for the driver until hangs
- *     reported against non-IA acrhs can be root-caused.
- *   o Back out the CSA fix for 82547 as it continues to cause
- *     systems lock-ups with production systems.
- *   o Fixed FC high/low water mark values to actually be in the
- *     range of the Rx FIFO area.  It was a math error.
- *     [Dainis Jonitis (dainis_jonitis@exigengroup.lv)]
- *   o Handle failure to get new resources when doing ethtool
- *     ring paramater changes.  Previously, driver would free old,
- *     but fails to allocate new, causing problems.  Now, driver 
- *     allocates new, and if sucessful, frees old.
- *   o Changed collision threshold from 16 to 15 to comply with IEEE
- *     spec.
- *   o Toggle chip-select when checking ready status on SPI eeproms.
- *   o Put PHY into class A mode to pass IEEE tests on some designs.
- *     Designs with EEPROM word 0x7, bit 15 set will have their PHYs
- *     set to class A mode, rather than the default class AB.
- *   o Handle failures of register_netdev.  Stephen Hemminger
- *     [shemminger@osdl.org].
- *   o updated README & MAN pages, number of Transmit/Receive
- *     descriptors may be denied depending on system resources.
- *
- * 5.2.30	1/14/03
- *   o Set VLAN filtering to IEEE 802.1Q after reset so we don't break
- *     SoL connections that use VLANs.
- *   o Allow 1000/Full setting for AutoNeg param for Fiber connections
- *     Jon D Mason [jonmason@us.ibm.com].
- *   o Race between Tx queue and Tx clean fixed with a spin lock.
- *   o Added netpoll support.
- *   o Fixed endianess bug causing ethtool loopback diags to fail on ppc.
- *   o Use pdev->irq rather than netdev->irq in preparation for MSI support.
- *   o Report driver message on user override of InterruptThrottleRate
- *     module parameter.
- *   o Change I/O address storage from uint32_t to unsigned long.
- *   o Added ethtool RINGPARAM support.
- *
- * 5.2.22	10/15/03
  */
 
 char e1000_driver_name[] = "e1000";
 char e1000_driver_string[] = "Intel(R) PRO/1000 Network Driver";
-char e1000_driver_version[] = "5.2.39-k2";
+char e1000_driver_version[] = "5.2.52-k2";
 char e1000_copyright[] = "Copyright (c) 1999-2004 Intel Corporation.";
 
 /* e1000_pci_tbl - PCI Device ID Table
@@ -170,6 +147,7 @@ static void e1000_alloc_rx_buffers(struct e1000_adapter *adapter);
 static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd);
 static int e1000_mii_ioctl(struct net_device *netdev, struct ifreq *ifr,
 			   int cmd);
+void set_ethtool_ops(struct net_device *netdev);
 static void e1000_enter_82542_rst(struct e1000_adapter *adapter);
 static void e1000_leave_82542_rst(struct e1000_adapter *adapter);
 static inline void e1000_rx_checksum(struct e1000_adapter *adapter,
@@ -206,7 +184,7 @@ struct notifier_block e1000_notifier_reboot = {
 /* Exported from other modules */
 
 extern void e1000_check_options(struct e1000_adapter *adapter);
-extern int e1000_ethtool_ioctl(struct net_device *netdev, struct ifreq *ifr);
+
 
 static struct pci_driver e1000_driver = {
 	.name     = e1000_driver_name,
@@ -224,6 +202,10 @@ MODULE_AUTHOR("Intel Corporation, <linux.nics@intel.com>");
 MODULE_DESCRIPTION("Intel(R) PRO/1000 Network Driver");
 MODULE_LICENSE("GPL");
 
+static int debug = 3;
+module_param(debug, int, 0);
+MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)");
+
 /**
  * e1000_init_module - Driver Registration Routine
  *
@@ -419,6 +401,12 @@ e1000_probe(struct pci_dev *pdev,
 	adapter->netdev = netdev;
 	adapter->pdev = pdev;
 	adapter->hw.back = adapter;
+	adapter->msg_enable = (1 << debug) - 1;
+
+	rtnl_lock();
+	/* we need to set the name early since the DPRINTK macro needs it set */
+	if (dev_alloc_name(netdev, netdev->name) < 0) 
+		goto err_free_unlock;
 
 	mmio_start = pci_resource_start(pdev, BAR_0);
 	mmio_len = pci_resource_len(pdev, BAR_0);
@@ -446,6 +434,7 @@ e1000_probe(struct pci_dev *pdev,
 	netdev->set_mac_address = &e1000_set_mac;
 	netdev->change_mtu = &e1000_change_mtu;
 	netdev->do_ioctl = &e1000_ioctl;
+	set_ethtool_ops(netdev);
 	netdev->tx_timeout = &e1000_tx_timeout;
 	netdev->watchdog_timeo = 5 * HZ;
 #ifdef CONFIG_E1000_NAPI
@@ -502,7 +491,7 @@ e1000_probe(struct pci_dev *pdev,
 	/* make sure the EEPROM is good */
 
 	if(e1000_validate_eeprom_checksum(&adapter->hw) < 0) {
-		printk(KERN_ERR "The EEPROM Checksum Is Not Valid\n");
+		DPRINTK(PROBE, ERR, "The EEPROM Checksum Is Not Valid\n");
 		err = -EIO;
 		goto err_eeprom;
 	}
@@ -536,16 +525,12 @@ e1000_probe(struct pci_dev *pdev,
 	INIT_WORK(&adapter->tx_timeout_task,
 		(void (*)(void *))e1000_tx_timeout_task, netdev);
 
-	if((err = register_netdev(netdev)))
-		goto err_register;
-
 	/* we're going to reset, so assume we have no link for now */
 
 	netif_carrier_off(netdev);
 	netif_stop_queue(netdev);
 
-	printk(KERN_INFO "%s: Intel(R) PRO/1000 Network Connection\n",
-	       netdev->name);
+	DPRINTK(PROBE, INFO, "Intel(R) PRO/1000 Network Connection\n");
 	e1000_check_options(adapter);
 
 	/* Initial Wake on LAN setting
@@ -579,7 +564,12 @@ e1000_probe(struct pci_dev *pdev,
 
 	e1000_reset(adapter);
 
+	/* since we are holding the rtnl lock already, call the no-lock version */
+	if((err = register_netdevice(netdev)))
+		goto err_register;
+
 	cards_found++;
+	rtnl_unlock();
 	return 0;
 
 err_register:
@@ -587,6 +577,8 @@ e1000_probe(struct pci_dev *pdev,
 err_eeprom:
 	iounmap(adapter->hw.hw_addr);
 err_ioremap:
+err_free_unlock:
+	rtnl_unlock();
 	free_netdev(netdev);
 err_alloc_etherdev:
 	pci_release_regions(pdev);
@@ -664,7 +656,7 @@ e1000_sw_init(struct e1000_adapter *adapter)
 	/* identify the MAC */
 
 	if (e1000_set_mac_type(hw)) {
-		E1000_ERR("Unknown MAC Type\n");
+		DPRINTK(PROBE, ERR, "Unknown MAC Type\n");
 		return -EIO;
 	}
 
@@ -1391,9 +1383,8 @@ e1000_watchdog(unsigned long data)
 			                           &adapter->link_speed,
 			                           &adapter->link_duplex);
 
-			printk(KERN_INFO
-			       "e1000: %s NIC Link is Up %d Mbps %s\n",
-			       netdev->name, adapter->link_speed,
+			DPRINTK(LINK, INFO, "NIC Link is Up %d Mbps %s\n",
+			       adapter->link_speed,
 			       adapter->link_duplex == FULL_DUPLEX ?
 			       "Full Duplex" : "Half Duplex");
 
@@ -1406,9 +1397,7 @@ e1000_watchdog(unsigned long data)
 		if(netif_carrier_ok(netdev)) {
 			adapter->link_speed = 0;
 			adapter->link_duplex = 0;
-			printk(KERN_INFO
-			       "e1000: %s NIC Link is Down\n",
-			       netdev->name);
+			DPRINTK(LINK, INFO, "NIC Link is Down\n");
 			netif_carrier_off(netdev);
 			netif_stop_queue(netdev);
 			mod_timer(&adapter->phy_info_timer, jiffies + 2 * HZ);
@@ -1560,33 +1549,17 @@ e1000_tx_csum(struct e1000_adapter *adapter, struct sk_buff *skb)
 
 static inline int
 e1000_tx_map(struct e1000_adapter *adapter, struct sk_buff *skb,
-	unsigned int first)
+	unsigned int first, unsigned int max_per_txd,
+	unsigned int nr_frags, unsigned int mss)
 {
 	struct e1000_desc_ring *tx_ring = &adapter->tx_ring;
-	struct e1000_tx_desc *tx_desc;
 	struct e1000_buffer *buffer_info;
-	unsigned int len = skb->len, max_per_txd = E1000_MAX_DATA_PER_TXD;
+	unsigned int len = skb->len;
 	unsigned int offset = 0, size, count = 0, i;
-#ifdef NETIF_F_TSO
-	unsigned int mss;
-#endif
-	unsigned int nr_frags;
 	unsigned int f;
-
-#ifdef NETIF_F_TSO
-	mss = skb_shinfo(skb)->tso_size;
-	/* The controller does a simple calculation to 
-	 * make sure there is enough room in the FIFO before
-	 * initiating the DMA for each buffer.  The calc is:
-	 * 4 = ceil(buffer len/mss).  To make sure we don't
-	 * overrun the FIFO, adjust the max buffer len if mss
-	 * drops. */
-	if(mss)
-		max_per_txd = min(mss << 2, max_per_txd);
-#endif
-	nr_frags = skb_shinfo(skb)->nr_frags;
 	len -= skb->data_len;
 
+
 	i = tx_ring->next_to_use;
 
 	while(len) {
@@ -1658,46 +1631,6 @@ e1000_tx_map(struct e1000_adapter *adapter, struct sk_buff *skb,
 			if(++i == tx_ring->count) i = 0;
 		}
 	}
-
-	if(E1000_DESC_UNUSED(&adapter->tx_ring) < count + 2) {
-
-		/* There aren't enough descriptors available to queue up
-		 * this send (need: count + 1 context desc + 1 desc gap
-		 * to keep tail from touching head), so undo the mapping
-		 * and abort the send.  We could have done the check before
-		 * we mapped the skb, but because of all the workarounds
-		 * (above), it's too difficult to predict how many we're
-		 * going to need.*/
-		i = tx_ring->next_to_use;
-
-		if(i == first) {
-			/* Cleanup after e1000_tx_[csum|tso] scribbling
-			 * on descriptors. */
-			tx_desc = E1000_TX_DESC(*tx_ring, first);
-			tx_desc->buffer_addr = 0;
-			tx_desc->lower.data = 0;
-			tx_desc->upper.data = 0;
-		}
-
-		while(count--) {
-			buffer_info = &tx_ring->buffer_info[i];
-
-			if(buffer_info->dma) {
-				pci_unmap_page(adapter->pdev,
-					       buffer_info->dma,
-					       buffer_info->length,
-					       PCI_DMA_TODEVICE);
-				buffer_info->dma = 0;
-			}
-
-			if(++i == tx_ring->count) i = 0;
-		}
-
-		tx_ring->next_to_use = first;
-
-		return 0;
-	}
-
 	i = (i == 0) ? tx_ring->count - 1 : i - 1;
 	tx_ring->buffer_info[i].skb = skb;
 	tx_ring->buffer_info[first].next_to_watch = i;
@@ -1792,27 +1725,72 @@ e1000_82547_fifo_workaround(struct e1000_adapter *adapter, struct sk_buff *skb)
 	return 0;
 }
 
+#define TXD_USE_COUNT(S, X) (((S) >> (X)) + 1 ) 
 static int
 e1000_xmit_frame(struct sk_buff *skb, struct net_device *netdev)
 {
 	struct e1000_adapter *adapter = netdev->priv;
-	unsigned int first;
+	unsigned int first, max_per_txd = E1000_MAX_DATA_PER_TXD;
+	unsigned int max_txd_pwr = E1000_MAX_TXD_PWR;
 	unsigned int tx_flags = 0;
 	unsigned long flags;
-	int count;
-
+	unsigned int len = skb->len;
+	int count = 0;
+	unsigned int mss = 0;
+	unsigned int nr_frags = 0;
+	unsigned int f;
+	nr_frags = skb_shinfo(skb)->nr_frags;
+	len -= skb->data_len;
 	if(skb->len <= 0) {
 		dev_kfree_skb_any(skb);
 		return 0;
 	}
 
+#ifdef NETIF_F_TSO
+	mss = skb_shinfo(skb)->tso_size;
+	/* The controller does a simple calculation to 
+	 * make sure there is enough room in the FIFO before
+	 * initiating the DMA for each buffer.  The calc is:
+	 * 4 = ceil(buffer len/mss).  To make sure we don't
+	 * overrun the FIFO, adjust the max buffer len if mss
+	 * drops. */
+	if(mss) {
+		max_per_txd = min(mss << 2, max_per_txd);
+		max_txd_pwr = fls(max_per_txd) - 1;
+	}
+	if((mss) || (skb->ip_summed == CHECKSUM_HW))
+		count++;
+	count++;	/*for sentinel desc*/
+#else
+	if(skb->ip_summed == CHECKSUM_HW)
+		count++;
+#endif
+
+	count += TXD_USE_COUNT(len, max_txd_pwr);
+	if(adapter->pcix_82544)
+		count++;
+
+	nr_frags = skb_shinfo(skb)->nr_frags;
+	for(f = 0; f < nr_frags; f++)
+		count += TXD_USE_COUNT(skb_shinfo(skb)->frags[f].size,
+		                       max_txd_pwr);
+	if(adapter->pcix_82544)
+		count += nr_frags;
+	
 	spin_lock_irqsave(&adapter->tx_lock, flags);
+	/* need: count +  2 desc gap to keep tail from touching 
+	 * head, otherwise try next time */
+	if(E1000_DESC_UNUSED(&adapter->tx_ring) < count + 2 ) {
+		netif_stop_queue(netdev);
+		spin_unlock_irqrestore(&adapter->tx_lock, flags);
+		return 1;
+	}
+	spin_unlock_irqrestore(&adapter->tx_lock, flags);
 
 	if(adapter->hw.mac_type == e1000_82547) {
 		if(e1000_82547_fifo_workaround(adapter, skb)) {
 			netif_stop_queue(netdev);
 			mod_timer(&adapter->tx_fifo_stall_timer, jiffies);
-			spin_unlock_irqrestore(&adapter->tx_lock, flags);
 			return 1;
 		}
 	}
@@ -1829,18 +1807,12 @@ e1000_xmit_frame(struct sk_buff *skb, struct net_device *netdev)
 	else if(e1000_tx_csum(adapter, skb))
 		tx_flags |= E1000_TX_FLAGS_CSUM;
 
-	if((count = e1000_tx_map(adapter, skb, first)))
-		e1000_tx_queue(adapter, count, tx_flags);
-	else {
-		netif_stop_queue(netdev);
-		spin_unlock_irqrestore(&adapter->tx_lock, flags);
-		return 1;
-	}
+	e1000_tx_queue(adapter, 
+		e1000_tx_map(adapter, skb, first, max_per_txd, nr_frags, mss), 
+		tx_flags);
 
 	netdev->trans_start = jiffies;
 
-	spin_unlock_irqrestore(&adapter->tx_lock, flags);
-	
 	return 0;
 }
 
@@ -1903,7 +1875,7 @@ e1000_change_mtu(struct net_device *netdev, int new_mtu)
 
 	if((max_frame < MINIMUM_ETHERNET_FRAME_SIZE) ||
 	   (max_frame > MAX_JUMBO_FRAME_SIZE)) {
-		E1000_ERR("Invalid MTU setting\n");
+		DPRINTK(PROBE, ERR, "Invalid MTU setting\n");
 		return -EINVAL;
 	}
 
@@ -1911,7 +1883,7 @@ e1000_change_mtu(struct net_device *netdev, int new_mtu)
 		adapter->rx_buffer_len = E1000_RXBUFFER_2048;
 
 	} else if(adapter->hw.mac_type < e1000_82543) {
-		E1000_ERR("Jumbo Frames not supported on 82542\n");
+		DPRINTK(PROBE, ERR, "Jumbo Frames not supported on 82542\n");
 		return -EINVAL;
 
 	} else if(max_frame <= E1000_RXBUFFER_4096) {
@@ -2193,7 +2165,6 @@ e1000_clean_tx_irq(struct e1000_adapter *adapter)
 	unsigned int i, eop;
 	boolean_t cleaned = FALSE;
 
-	spin_lock(&adapter->tx_lock);
 
 	i = tx_ring->next_to_clean;
 	eop = tx_ring->buffer_info[i].next_to_watch;
@@ -2236,6 +2207,8 @@ e1000_clean_tx_irq(struct e1000_adapter *adapter)
 
 	tx_ring->next_to_clean = i;
 
+	spin_lock(&adapter->tx_lock);
+
 	if(cleaned && netif_queue_stopped(netdev) && netif_carrier_ok(netdev))
 		netif_wake_queue(netdev);
 
@@ -2296,7 +2269,8 @@ e1000_clean_rx_irq(struct e1000_adapter *adapter)
 
 			/* All receives must fit into a single buffer */
 
-			E1000_DBG("Receive packet consumed multiple buffers\n");
+			E1000_DBG("%s: Receive packet consumed multiple buffers\n",
+				netdev->name);
 
 			dev_kfree_skb_irq(skb);
 			rx_desc->status = 0;
@@ -2513,8 +2487,6 @@ e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
 	case SIOCGMIIREG:
 	case SIOCSMIIREG:
 		return e1000_mii_ioctl(netdev, ifr, cmd);
-	case SIOCETHTOOL:
-		return e1000_ethtool_ioctl(netdev, ifr);
 	default:
 		return -EOPNOTSUPP;
 	}

drivers/net/e1000/e1000_param.c

@@ -234,7 +234,8 @@ struct e1000_option {
 };
 
 static int __devinit
-e1000_validate_option(int *value, struct e1000_option *opt)
+e1000_validate_option(int *value, struct e1000_option *opt,
+	struct e1000_adapter *adapter)
 {
 	if(*value == OPTION_UNSET) {
 		*value = opt->def;
@@ -245,16 +246,17 @@ e1000_validate_option(int *value, struct e1000_option *opt)
 	case enable_option:
 		switch (*value) {
 		case OPTION_ENABLED:
-			printk(KERN_INFO "%s Enabled\n", opt->name);
+			DPRINTK(PROBE, INFO, "%s Enabled\n", opt->name);
 			return 0;
 		case OPTION_DISABLED:
-			printk(KERN_INFO "%s Disabled\n", opt->name);
+			DPRINTK(PROBE, INFO, "%s Disabled\n", opt->name);
 			return 0;
 		}
 		break;
 	case range_option:
 		if(*value >= opt->arg.r.min && *value <= opt->arg.r.max) {
-			printk(KERN_INFO "%s set to %i\n", opt->name, *value);
+			DPRINTK(PROBE, INFO,
+				"%s set to %i\n", opt->name, *value);
 			return 0;
 		}
 		break;
@@ -266,7 +268,7 @@ e1000_validate_option(int *value, struct e1000_option *opt)
 			ent = &opt->arg.l.p[i];
 			if(*value == ent->i) {
 				if(ent->str[0] != '\0')
-					printk(KERN_INFO "%s\n", ent->str);
+					DPRINTK(PROBE, INFO, "%s\n", ent->str);
 				return 0;
 			}
 		}
@@ -276,7 +278,7 @@ e1000_validate_option(int *value, struct e1000_option *opt)
 		BUG();
 	}
 
-	printk(KERN_INFO "Invalid %s specified (%i) %s\n",
+	DPRINTK(PROBE, INFO, "Invalid %s specified (%i) %s\n",
 	       opt->name, *value, opt->err);
 	*value = opt->def;
 	return -1;
@@ -300,9 +302,9 @@ e1000_check_options(struct e1000_adapter *adapter)
 {
 	int bd = adapter->bd_number;
 	if(bd >= E1000_MAX_NIC) {
-		printk(KERN_NOTICE
+		DPRINTK(PROBE, NOTICE,
 		       "Warning: no configuration for board #%i\n", bd);
-		printk(KERN_NOTICE "Using defaults for all values\n");
+		DPRINTK(PROBE, NOTICE, "Using defaults for all values\n");
 		bd = E1000_MAX_NIC;
 	}
 
@@ -321,7 +323,7 @@ e1000_check_options(struct e1000_adapter *adapter)
 			E1000_MAX_TXD : E1000_MAX_82544_TXD;
 
 		tx_ring->count = TxDescriptors[bd];
-		e1000_validate_option(&tx_ring->count, &opt);
+		e1000_validate_option(&tx_ring->count, &opt, adapter);
 		E1000_ROUNDUP(tx_ring->count, REQ_TX_DESCRIPTOR_MULTIPLE);
 	}
 	{ /* Receive Descriptor Count */
@@ -339,7 +341,7 @@ e1000_check_options(struct e1000_adapter *adapter)
 			E1000_MAX_82544_RXD;
 
 		rx_ring->count = RxDescriptors[bd];
-		e1000_validate_option(&rx_ring->count, &opt);
+		e1000_validate_option(&rx_ring->count, &opt, adapter);
 		E1000_ROUNDUP(rx_ring->count, REQ_RX_DESCRIPTOR_MULTIPLE);
 	}
 	{ /* Checksum Offload Enable/Disable */
@@ -351,7 +353,7 @@ e1000_check_options(struct e1000_adapter *adapter)
 		};
 
 		int rx_csum = XsumRX[bd];
-		e1000_validate_option(&rx_csum, &opt);
+		e1000_validate_option(&rx_csum, &opt, adapter);
 		adapter->rx_csum = rx_csum;
 	}
 	{ /* Flow Control */
@@ -373,7 +375,7 @@ e1000_check_options(struct e1000_adapter *adapter)
 		};
 
 		int fc = FlowControl[bd];
-		e1000_validate_option(&fc, &opt);
+		e1000_validate_option(&fc, &opt, adapter);
 		adapter->hw.fc = adapter->hw.original_fc = fc;
 	}
 	{ /* Transmit Interrupt Delay */
@@ -387,7 +389,7 @@ e1000_check_options(struct e1000_adapter *adapter)
 		};
 
 		adapter->tx_int_delay = TxIntDelay[bd];
-		e1000_validate_option(&adapter->tx_int_delay, &opt);
+		e1000_validate_option(&adapter->tx_int_delay, &opt, adapter);
 	}
 	{ /* Transmit Absolute Interrupt Delay */
 		struct e1000_option opt = {
@@ -400,7 +402,7 @@ e1000_check_options(struct e1000_adapter *adapter)
 		};
 
 		adapter->tx_abs_int_delay = TxAbsIntDelay[bd];
-		e1000_validate_option(&adapter->tx_abs_int_delay, &opt);
+		e1000_validate_option(&adapter->tx_abs_int_delay, &opt, adapter);
 	}
 	{ /* Receive Interrupt Delay */
 		struct e1000_option opt = {
@@ -413,7 +415,7 @@ e1000_check_options(struct e1000_adapter *adapter)
 		};
 
 		adapter->rx_int_delay = RxIntDelay[bd];
-		e1000_validate_option(&adapter->rx_int_delay, &opt);
+		e1000_validate_option(&adapter->rx_int_delay, &opt, adapter);
 	}
 	{ /* Receive Absolute Interrupt Delay */
 		struct e1000_option opt = {
@@ -426,7 +428,7 @@ e1000_check_options(struct e1000_adapter *adapter)
 		};
 
 		adapter->rx_abs_int_delay = RxAbsIntDelay[bd];
-		e1000_validate_option(&adapter->rx_abs_int_delay, &opt);
+		e1000_validate_option(&adapter->rx_abs_int_delay, &opt, adapter);
 	}
 	{ /* Interrupt Throttling Rate */
 		struct e1000_option opt = {
@@ -444,13 +446,14 @@ e1000_check_options(struct e1000_adapter *adapter)
 			adapter->itr = 1;
 			break;
 		case 0:
-			printk(KERN_INFO "%s turned off\n", opt.name);
+			DPRINTK(PROBE, INFO, "%s turned off\n", opt.name);
 			break;
 		case 1:
-			printk(KERN_INFO "%s set to dynamic mode\n", opt.name);
+			DPRINTK(PROBE, INFO,
+				"%s set to dynamic mode\n", opt.name);
 			break;
 		default:
-			e1000_validate_option(&adapter->itr, &opt);
+			e1000_validate_option(&adapter->itr, &opt, adapter);
 			break;
 		}
 	}
@@ -482,15 +485,15 @@ e1000_check_fiber_options(struct e1000_adapter *adapter)
 	bd = bd > E1000_MAX_NIC ? E1000_MAX_NIC : bd;
 
 	if((Speed[bd] != OPTION_UNSET)) {
-		printk(KERN_INFO "Speed not valid for fiber adapters, "
+		DPRINTK(PROBE, INFO, "Speed not valid for fiber adapters, "
 		       "parameter ignored\n");
 	}
 	if((Duplex[bd] != OPTION_UNSET)) {
-		printk(KERN_INFO "Duplex not valid for fiber adapters, "
+		DPRINTK(PROBE, INFO, "Duplex not valid for fiber adapters, "
 		       "parameter ignored\n");
 	}
 	if((AutoNeg[bd] != OPTION_UNSET) && (AutoNeg[bd] != 0x20)) {
-		printk(KERN_INFO "AutoNeg other than Full/1000 is "
+		DPRINTK(PROBE, INFO, "AutoNeg other than Full/1000 is "
 		       "not valid for fiber adapters, parameter ignored\n");
 	}
 }
@@ -525,7 +528,7 @@ e1000_check_copper_options(struct e1000_adapter *adapter)
 		};
 
 		speed = Speed[bd];
-		e1000_validate_option(&speed, &opt);
+		e1000_validate_option(&speed, &opt, adapter);
 	}
 	{ /* Duplex */
 		struct e1000_opt_list dplx_list[] = {{           0, "" },
@@ -542,11 +545,11 @@ e1000_check_copper_options(struct e1000_adapter *adapter)
 		};
 
 		dplx = Duplex[bd];
-		e1000_validate_option(&dplx, &opt);
+		e1000_validate_option(&dplx, &opt, adapter);
 	}
 
 	if(AutoNeg[bd] != OPTION_UNSET && (speed != 0 || dplx != 0)) {
-		printk(KERN_INFO
+		DPRINTK(PROBE, INFO,
 		       "AutoNeg specified along with Speed or Duplex, "
 		       "parameter ignored\n");
 		adapter->hw.autoneg_advertised = AUTONEG_ADV_DEFAULT;
@@ -595,7 +598,7 @@ e1000_check_copper_options(struct e1000_adapter *adapter)
 		};
 
 		int an = AutoNeg[bd];
-		e1000_validate_option(&an, &opt);
+		e1000_validate_option(&an, &opt, adapter);
 		adapter->hw.autoneg_advertised = an;
 	}
 
@@ -603,78 +606,85 @@ e1000_check_copper_options(struct e1000_adapter *adapter)
 	case 0:
 		adapter->hw.autoneg = adapter->fc_autoneg = 1;
 		if(Speed[bd] != OPTION_UNSET || Duplex[bd] != OPTION_UNSET)
-			printk(KERN_INFO
+			DPRINTK(PROBE, INFO,
 			       "Speed and duplex autonegotiation enabled\n");
 		break;
 	case HALF_DUPLEX:
-		printk(KERN_INFO "Half Duplex specified without Speed\n");
-		printk(KERN_INFO "Using Autonegotiation at Half Duplex only\n");
+		DPRINTK(PROBE, INFO, "Half Duplex specified without Speed\n");
+		DPRINTK(PROBE, INFO,
+			"Using Autonegotiation at Half Duplex only\n");
 		adapter->hw.autoneg = adapter->fc_autoneg = 1;
 		adapter->hw.autoneg_advertised = ADVERTISE_10_HALF |
 		                                 ADVERTISE_100_HALF;
 		break;
 	case FULL_DUPLEX:
-		printk(KERN_INFO "Full Duplex specified without Speed\n");
-		printk(KERN_INFO "Using Autonegotiation at Full Duplex only\n");
+		DPRINTK(PROBE, INFO, "Full Duplex specified without Speed\n");
+		DPRINTK(PROBE, INFO,
+			"Using Autonegotiation at Full Duplex only\n");
 		adapter->hw.autoneg = adapter->fc_autoneg = 1;
 		adapter->hw.autoneg_advertised = ADVERTISE_10_FULL |
 		                                 ADVERTISE_100_FULL |
 		                                 ADVERTISE_1000_FULL;
 		break;
 	case SPEED_10:
-		printk(KERN_INFO "10 Mbps Speed specified without Duplex\n");
-		printk(KERN_INFO "Using Autonegotiation at 10 Mbps only\n");
+		DPRINTK(PROBE, INFO,
+			"10 Mbps Speed specified without Duplex\n");
+		DPRINTK(PROBE, INFO, "Using Autonegotiation at 10 Mbps only\n");
 		adapter->hw.autoneg = adapter->fc_autoneg = 1;
 		adapter->hw.autoneg_advertised = ADVERTISE_10_HALF |
 		                                 ADVERTISE_10_FULL;
 		break;
 	case SPEED_10 + HALF_DUPLEX:
-		printk(KERN_INFO "Forcing to 10 Mbps Half Duplex\n");
+		DPRINTK(PROBE, INFO, "Forcing to 10 Mbps Half Duplex\n");
 		adapter->hw.autoneg = adapter->fc_autoneg = 0;
 		adapter->hw.forced_speed_duplex = e1000_10_half;
 		adapter->hw.autoneg_advertised = 0;
 		break;
 	case SPEED_10 + FULL_DUPLEX:
-		printk(KERN_INFO "Forcing to 10 Mbps Full Duplex\n");
+		DPRINTK(PROBE, INFO, "Forcing to 10 Mbps Full Duplex\n");
 		adapter->hw.autoneg = adapter->fc_autoneg = 0;
 		adapter->hw.forced_speed_duplex = e1000_10_full;
 		adapter->hw.autoneg_advertised = 0;
 		break;
 	case SPEED_100:
-		printk(KERN_INFO "100 Mbps Speed specified without Duplex\n");
-		printk(KERN_INFO "Using Autonegotiation at 100 Mbps only\n");
+		DPRINTK(PROBE, INFO,
+			"100 Mbps Speed specified without Duplex\n");
+		DPRINTK(PROBE, INFO,
+			"Using Autonegotiation at 100 Mbps only\n");
 		adapter->hw.autoneg = adapter->fc_autoneg = 1;
 		adapter->hw.autoneg_advertised = ADVERTISE_100_HALF |
 		                                 ADVERTISE_100_FULL;
 		break;
 	case SPEED_100 + HALF_DUPLEX:
-		printk(KERN_INFO "Forcing to 100 Mbps Half Duplex\n");
+		DPRINTK(PROBE, INFO, "Forcing to 100 Mbps Half Duplex\n");
 		adapter->hw.autoneg = adapter->fc_autoneg = 0;
 		adapter->hw.forced_speed_duplex = e1000_100_half;
 		adapter->hw.autoneg_advertised = 0;
 		break;
 	case SPEED_100 + FULL_DUPLEX:
-		printk(KERN_INFO "Forcing to 100 Mbps Full Duplex\n");
+		DPRINTK(PROBE, INFO, "Forcing to 100 Mbps Full Duplex\n");
 		adapter->hw.autoneg = adapter->fc_autoneg = 0;
 		adapter->hw.forced_speed_duplex = e1000_100_full;
 		adapter->hw.autoneg_advertised = 0;
 		break;
 	case SPEED_1000:
-		printk(KERN_INFO "1000 Mbps Speed specified without Duplex\n");
-		printk(KERN_INFO
+		DPRINTK(PROBE, INFO,
+			"1000 Mbps Speed specified without Duplex\n");
+		DPRINTK(PROBE, INFO,
 		       "Using Autonegotiation at 1000 Mbps Full Duplex only\n");
 		adapter->hw.autoneg = adapter->fc_autoneg = 1;
 		adapter->hw.autoneg_advertised = ADVERTISE_1000_FULL;
 		break;
 	case SPEED_1000 + HALF_DUPLEX:
-		printk(KERN_INFO "Half Duplex is not supported at 1000 Mbps\n");
-		printk(KERN_INFO
+		DPRINTK(PROBE, INFO,
+			"Half Duplex is not supported at 1000 Mbps\n");
+		DPRINTK(PROBE, INFO,
 		       "Using Autonegotiation at 1000 Mbps Full Duplex only\n");
 		adapter->hw.autoneg = adapter->fc_autoneg = 1;
 		adapter->hw.autoneg_advertised = ADVERTISE_1000_FULL;
 		break;
 	case SPEED_1000 + FULL_DUPLEX:
-		printk(KERN_INFO
+		DPRINTK(PROBE, INFO,
 		       "Using Autonegotiation at 1000 Mbps Full Duplex only\n");
 		adapter->hw.autoneg = adapter->fc_autoneg = 1;
 		adapter->hw.autoneg_advertised = ADVERTISE_1000_FULL;
@@ -685,7 +695,8 @@ e1000_check_copper_options(struct e1000_adapter *adapter)
 
 	/* Speed, AutoNeg and MDI/MDI-X must all play nice */
 	if (e1000_validate_mdi_setting(&(adapter->hw)) < 0) {
-		printk(KERN_INFO "Speed, AutoNeg and MDI-X specifications are "
+		DPRINTK(PROBE, INFO,
+		       "Speed, AutoNeg and MDI-X specifications are "
 		       "incompatible. Setting MDI-X to a compatible value.\n");
 	}
 }