Merge tag 'regulator-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator

Pull regulator updates from Mark Brown:
 "This has been a very busy release for the core, some fixes, one large
  new feature and a big bit of refactoring to update the GPIO API:

   - Support for coupled regulators from Dmitry Osipenko based on a
     prior attempt by Maciej Purski, allowing us to handle situations
     where the voltages on two regulators can't be too far apart from
     each other.

   - Conversion of the GPIO support in both drivers and the core to use
     GPIO descriptors rather than numbers, part of the overall project
     to remove GPIO numbers.

   - Support for standby mode suspend states from Andrei Stefanescu.

   - New drivers for Allwinner AXP209, Cirrus Logic Lochnagar and
     Microchip MPC16502"

* tag 'regulator-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (90 commits)
  regulator: tps65910: fix a missing check of return value
  regulator: mcp16502: Select REGMAP_I2C to fix build error
  regulator: convert to DEFINE_SHOW_ATTRIBUTE
  regulator: mcp16502: Fix missing n_voltages setting
  regulator: mcp16502: Use #ifdef CONFIG_PM_SLEEP around mcp16502_suspend/resume_noirq
  regulator: mcp16502: code cleanup
  regulator: act8945a-regulator: make symbol act8945a_pm static
  drivers/regulator: fix a missing check of return value
  regulator: act8945a-regulator: fix 'defined but not used' compiler warning
  regulator: axp20x: fix set_ramp_delay for AXP209/dcdc2
  regulator: mcp16502: add support for suspend
  mfd: axp20x: use explicit bit defines
  mfd: axp20x: Clean up included headers
  regulator: dts: enable soft-start and ramp delay for the OLinuXino Lime2
  dt-bindings: mfd: axp20x: Add software based soft_start for AXP209 LDO3
  regulator: axp20x: add software based soft_start for AXP209 LDO3
  dt-bindings: mfd: axp20x: add support for regulator-ramp-delay for AXP209
  regulator: axp20x: add support for set_ramp_delay for AXP209
  mfd: axp20x: name voltage ramping define properly
  regulator: mcp16502: add regulator driver for MCP16502
  ...

Documentation/devicetree/bindings/mfd/axp20x.txt

@@ -32,6 +32,15 @@ Required properties:
 - interrupt-controller: The PMIC has its own internal IRQs
 - #interrupt-cells: Should be set to 1
 
+Supported common regulator properties, see ../regulator/regulator.txt for
+more information:
+- regulator-ramp-delay: sets the ramp up delay in uV/us
+			AXP20x/DCDC2: 1600, 800
+			AXP20x/LDO3:  1600, 800
+- regulator-soft-start:	enable the output at the lowest possible voltage and
+			only then set the desired voltage
+			AXP20x/LDO3: software-based implementation
+
 Optional properties:
 - x-powers,dcdc-freq: defines the work frequency of DC-DC in KHz
 		      AXP152/20X: range:  750-1875, Default: 1.5 MHz

Documentation/devicetree/bindings/regulator/act8945a-regulator.txt

@@ -15,11 +15,17 @@ Optional input supply properties:
   - inl67-supply: The input supply for REG_LDO3 and REG_LDO4
 
 Any standard regulator properties can be used to configure the single regulator.
+regulator-initial-mode, regulator-allowed-modes and regulator-mode could be
+specified using mode values from dt-bindings/regulator/active-semi,8945a-regulator.h
+file.
 
 The valid names for regulators are:
 	REG_DCDC1, REG_DCDC2, REG_DCDC3, REG_LDO1, REG_LDO2, REG_LDO3, REG_LDO4.
 
 Example:
+
+#include <dt-bindings/regulator/active-semi,8945a-regulator.h>
+
 	pmic@5b {
 		compatible = "active-semi,act8945a";
 		reg = <0x5b>;
@@ -32,6 +38,18 @@ Example:
 				regulator-min-microvolt = <1350000>;
 				regulator-max-microvolt = <1350000>;
 				regulator-always-on;
+
+				regulator-allowed-modes = <ACT8945A_REGULATOR_MODE_FIXED>,
+							  <ACT8945A_REGULATOR_MODE_LOWPOWER>;
+				regulator-initial-mode = <ACT8945A_REGULATOR_MODE_FIXED>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-min-microvolt=<1400000>;
+					regulator-suspend-max-microvolt=<1400000>;
+					regulator-changeable-in-suspend;
+					regulator-mode=<ACT8945A_REGULATOR_MODE_LOWPOWER>;
+				};
 			};
 
 			vdd_1v2_reg: REG_DCDC2 {
@@ -39,6 +57,14 @@ Example:
 				regulator-min-microvolt = <1100000>;
 				regulator-max-microvolt = <1300000>;
 				regulator-always-on;
+
+				regulator-allowed-modes = <ACT8945A_REGULATOR_MODE_FIXED>,
+							  <ACT8945A_REGULATOR_MODE_LOWPOWER>;
+				regulator-initial-mode = <ACT8945A_REGULATOR_MODE_FIXED>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
 			};
 
 			vdd_3v3_reg: REG_DCDC3 {
@@ -53,6 +79,14 @@ Example:
 				regulator-min-microvolt = <2500000>;
 				regulator-max-microvolt = <2500000>;
 				regulator-always-on;
+
+				regulator-allowed-modes = <ACT8945A_REGULATOR_MODE_NORMAL>,
+							  <ACT8945A_REGULATOR_MODE_LOWPOWER>;
+				regulator-initial-mode = <ACT8945A_REGULATOR_MODE_NORMAL>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
 			};
 
 			vdd_3v3_lp_reg: REG_LDO2 {

Documentation/devicetree/bindings/regulator/cirrus,lochnagar.txt

+Cirrus Logic Lochnagar Audio Development Board
+
+Lochnagar is an evaluation and development board for Cirrus Logic
+Smart CODEC and Amp devices. It allows the connection of most Cirrus
+Logic devices on mini-cards, as well as allowing connection of
+various application processor systems to provide a full evaluation
+platform.  Audio system topology, clocking and power can all be
+controlled through the Lochnagar, allowing the device under test
+to be used in a variety of possible use cases.
+
+This binding document describes the binding for the regulator portion
+of the driver.
+
+Also see these documents for generic binding information:
+  [1] Regulator: ../regulator/regulator.txt
+
+This binding must be part of the Lochnagar MFD binding:
+  [2] ../mfd/cirrus,lochnagar.txt
+
+Optional sub-nodes:
+
+  - VDDCORE : Initialisation data for the VDDCORE regulator, which
+    supplies the CODECs digital core if it has no build regulator for that
+    purpose.
+      Required Properties:
+      - compatible : One of the following strings:
+                     "cirrus,lochnagar2-vddcore"
+      - SYSVDD-supply: Primary power supply for the Lochnagar.
+
+  - MICVDD : Initialisation data for the MICVDD regulator, which
+    supplies the CODECs MICVDD.
+      Required Properties:
+      - compatible : One of the following strings:
+                     "cirrus,lochnagar2-micvdd"
+      - SYSVDD-supply: Primary power supply for the Lochnagar.
+
+  - MIC1VDD, MIC2VDD : Initialisation data for the MICxVDD supplies.
+      Required Properties:
+      - compatible : One of the following strings:
+                     "cirrus,lochnagar2-mic1vdd", "cirrus,lochnagar2-mic2vdd"
+      Optional Properties:
+      - cirrus,micbias-input : A property selecting which of the CODEC
+        minicard micbias outputs should be used, valid values are 1 - 4.
+      - MICBIAS1-supply, MICBIAS2-supply: Regulator supplies for the
+        MICxVDD outputs, supplying the digital microphones, normally
+        supplied from the attached CODEC.
+
+  - VDD1V8 : Recommended fixed regulator for the VDD1V8 regulator, which supplies the
+    CODECs analog and 1.8V digital supplies.
+      Required Properties:
+      - compatible : Should be set to "regulator-fixed"
+      - regulator-min-microvolt : Should be set to 1.8V
+      - regulator-max-microvolt : Should be set to 1.8V
+      - regulator-boot-on
+      - regulator-always-on
+      - vin-supply : Should be set to same supply as SYSVDD
+
+Example:
+
+lochnagar {
+	lochnagar-micvdd: MICVDD {
+		compatible = "cirrus,lochnagar2-micvdd";
+
+		SYSVDD-supply = <&wallvdd>;
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	lochnagar-vdd1v8: VDD1V8 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VDD1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+
+		vin-supply = <&wallvdd>;
+	};
+};
+

Documentation/devicetree/bindings/regulator/mcp16502-regulator.txt

+MCP16502 PMIC
+
+Required properties:
+- compatible: "microchip,mcp16502"
+- reg: I2C slave address
+- lpm-gpios: GPIO for LPM pin. Note that this GPIO *must* remain high during
+	     suspend-to-ram, keeping the PMIC into HIBERNATE mode.
+- regulators: A node that houses a sub-node for each regulator within
+              the device. Each sub-node is identified using the node's
+              name. The content of each sub-node is defined by the
+              standard binding for regulators; see regulator.txt.
+
+Regualtors of MCP16502 PMIC:
+1) VDD_IO	- Buck (1.2 - 3.7 V)
+2) VDD_DDR	- Buck (0.6 - 1.85 V)
+3) VDD_CORE	- Buck (0.6 - 1.85 V)
+4) VDD_OTHER	- BUCK (0.6 - 1.85 V)
+5) LDO1		- LDO  (1.2 - 3.7 V)
+6) LDO2		- LDO  (1.2 - 3.7 V)
+
+Regulator modes:
+2 - FPWM: higher precision, higher consumption
+4 - AutoPFM: lower precision, lower consumption
+
+Each regulator is defined using the standard binding for regulators.
+
+Example:
+
+mcp16502@5b {
+	compatible = "microchip,mcp16502";
+	reg = <0x5b>;
+	status = "okay";
+	lpm-gpios = <&pioBU 7 GPIO_ACTIVE_HIGH>;
+
+	regulators {
+		VDD_IO {
+			regulator-name = "VDD_IO";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <3700000>;
+			regulator-initial-mode = <2>;
+			regulator-allowed-modes = <2>, <4>;
+			regulator-always-on;
+
+			regulator-state-standby {
+				regulator-on-in-suspend;
+				regulator-mode = <4>;
+			};
+
+			regulator-state-mem {
+				regulator-off-in-suspend;
+				regulator-mode = <4>;
+			};
+		};
+
+		VDD_DDR {
+			regulator-name = "VDD_DDR";
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <1850000>;
+			regulator-initial-mode = <2>;
+			regulator-allowed-modes = <2>, <4>;
+			regulator-always-on;
+
+			regulator-state-standby {
+				regulator-on-in-suspend;
+				regulator-mode = <4>;
+			};
+
+			regulator-state-mem {
+				regulator-on-in-suspend;
+				regulator-mode = <4>;
+			};
+		};
+
+		VDD_CORE {
+			regulator-name = "VDD_CORE";
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <1850000>;
+			regulator-initial-mode = <2>;
+			regulator-allowed-modes = <2>, <4>;
+			regulator-always-on;
+
+			regulator-state-standby {
+				regulator-on-in-suspend;
+				regulator-mode = <4>;
+			};
+
+			regulator-state-mem {
+				regulator-off-in-suspend;
+				regulator-mode = <4>;
+			};
+		};
+
+		VDD_OTHER {
+			regulator-name = "VDD_OTHER";
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <1850000>;
+			regulator-initial-mode = <2>;
+			regulator-allowed-modes = <2>, <4>;
+			regulator-always-on;
+
+			regulator-state-standby {
+				regulator-on-in-suspend;
+				regulator-mode = <4>;
+			};
+
+			regulator-state-mem {
+				regulator-off-in-suspend;
+				regulator-mode = <4>;
+			};
+		};
+
+		LDO1 {
+			regulator-name = "LDO1";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <3700000>;
+			regulator-always-on;
+
+			regulator-state-standby {
+				regulator-on-in-suspend;
+			};
+
+			regulator-state-mem {
+				regulator-off-in-suspend;
+			};
+		};
+
+		LDO2 {
+			regulator-name = "LDO2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <3700000>;
+			regulator-always-on;
+
+			regulator-state-standby {
+				regulator-on-in-suspend;
+			};
+
+			regulator-state-mem {
+				regulator-off-in-suspend;
+			};
+		};
+
+	};
+};

Documentation/devicetree/bindings/regulator/regulator.txt

@@ -33,13 +33,16 @@ Optional properties:
   decreases of any level. This is useful for regulators with exponential
   voltage changes.
 - regulator-soft-start: Enable soft start so that voltage ramps slowly
+- regulator-state-standby sub-root node for Standby mode
+  : equivalent with standby Linux sleep state, which provides energy savings
+  with a relatively quick transition back time.
 - regulator-state-mem sub-root node for Suspend-to-RAM mode
   : suspend to memory, the device goes to sleep, but all data stored in memory,
   only some external interrupt can wake the device.
 - regulator-state-disk sub-root node for Suspend-to-DISK mode
   : suspend to disk, this state operates similarly to Suspend-to-RAM,
   but includes a final step of writing memory contents to disk.
-- regulator-state-[mem/disk] node has following common properties:
+- regulator-state-[mem/disk/standby] node has following common properties:
 	- regulator-on-in-suspend: regulator should be on in suspend state.
 	- regulator-off-in-suspend: regulator should be off in suspend state.
 	- regulator-suspend-min-microvolt: minimum voltage may be set in
@@ -76,8 +79,11 @@ Optional properties:
 - regulator-coupled-with: Regulators with which the regulator
   is coupled. The linkage is 2-way - all coupled regulators should be linked
   with each other. A regulator should not be coupled with its supplier.
-- regulator-coupled-max-spread: Max spread between voltages of coupled regulators
-  in microvolts.
+- regulator-coupled-max-spread: Array of maximum spread between voltages of
+  coupled regulators in microvolts, each value in the array relates to the
+  corresponding couple specified by the regulator-coupled-with property.
+- regulator-max-step-microvolt: Maximum difference between current and target
+  voltages that can be changed safely in a single step.
 
 Deprecated properties:
 - regulator-compatible: If a regulator chip contains multiple

Documentation/driver-model/devres.txt

@@ -254,6 +254,7 @@ GPIO
   devm_gpiod_get_index_optional()
   devm_gpiod_get_optional()
   devm_gpiod_put()
+  devm_gpiod_unhinge()
   devm_gpiochip_add_data()
   devm_gpiochip_remove()
   devm_gpio_request()

MAINTAINERS

@@ -9891,6 +9891,13 @@ M:	Ludovic Desroches <ludovic.desroches@microchip.com>
 S:	Maintained
 F:	drivers/mmc/host/atmel-mci.c
 
+MICROCHIP MCP16502 PMIC DRIVER
+M:	Andrei Stefanescu <andrei.stefanescu@microchip.com>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+S:	Maintained
+F:	Documentation/devicetree/bindings/regulator/mcp16502-regulator.txt
+F:	drivers/regulator/mcp16502.c
+
 MICROCHIP MCP3911 ADC DRIVER
 M:	Marcus Folkesson <marcus.folkesson@gmail.com>
 M:	Kent Gustavsson <kent@minoris.se>

arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts

@@ -245,6 +245,8 @@ &reg_ldo3 {
 	regulator-min-microvolt = <2800000>;
 	regulator-max-microvolt = <2800000>;
 	regulator-name = "vddio-csi0";
+	regulator-soft-start;
+	regulator-ramp-delay = <1600>;
 };
 
 &reg_ldo4 {

arch/arm/mach-s3c64xx/mach-crag6410-module.c

@@ -194,8 +194,8 @@ static struct wm8994_pdata wm8994_pdata = {
 		0x3,          /* IRQ out, active high, CMOS */
 	},
 	.ldo = {
-		 { .enable = S3C64XX_GPN(6), .init_data = &wm8994_ldo1, },
-		 { .enable = S3C64XX_GPN(4), .init_data = &wm8994_ldo2, },
+		 { .init_data = &wm8994_ldo1, },
+		 { .init_data = &wm8994_ldo2, },
 	},
 };
 
@@ -203,6 +203,18 @@ static const struct i2c_board_info wm1277_devs[] = {
 	{ I2C_BOARD_INFO("wm8958", 0x1a),  /* WM8958 is the superset */
 	  .platform_data = &wm8994_pdata,
 	  .irq = GLENFARCLAS_PMIC_IRQ_BASE + WM831X_IRQ_GPIO_2,
+	  .dev_name = "wm8958",
+	},
+};
+
+static struct gpiod_lookup_table wm8994_gpiod_table = {
+	.dev_id = "i2c-wm8958", /* I2C device name */
+	.table = {
+		GPIO_LOOKUP("GPION", 6,
+			    "wlf,ldo1ena", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("GPION", 4,
+			    "wlf,ldo2ena", GPIO_ACTIVE_HIGH),
+		{ },
 	},
 };
 
@@ -381,6 +393,7 @@ static int wlf_gf_module_probe(struct i2c_client *i2c,
 
 	gpiod_add_lookup_table(&wm5102_reva_gpiod_table);
 	gpiod_add_lookup_table(&wm5102_gpiod_table);
+	gpiod_add_lookup_table(&wm8994_gpiod_table);
 
 	if (i < ARRAY_SIZE(gf_mods)) {
 		dev_info(&i2c->dev, "%s revision %d\n",

drivers/gpio/gpiolib-devres.c

@@ -98,15 +98,28 @@ struct gpio_desc *__must_check devm_gpiod_get_index(struct device *dev,
 	struct gpio_desc **dr;
 	struct gpio_desc *desc;
 
+	desc = gpiod_get_index(dev, con_id, idx, flags);
+	if (IS_ERR(desc))
+		return desc;
+
+	/*
+	 * For non-exclusive GPIO descriptors, check if this descriptor is
+	 * already under resource management by this device.
+	 */
+	if (flags & GPIOD_FLAGS_BIT_NONEXCLUSIVE) {
+		struct devres *dres;
+
+		dres = devres_find(dev, devm_gpiod_release,
+				   devm_gpiod_match, &desc);
+		if (dres)
+			return desc;
+	}
+
 	dr = devres_alloc(devm_gpiod_release, sizeof(struct gpio_desc *),
 			  GFP_KERNEL);
-	if (!dr)
+	if (!dr) {
+		gpiod_put(desc);
 		return ERR_PTR(-ENOMEM);
-
-	desc = gpiod_get_index(dev, con_id, idx, flags);
-	if (IS_ERR(desc)) {
-		devres_free(dr);
-		return desc;
 	}
 
 	*dr = desc;
@@ -140,15 +153,28 @@ struct gpio_desc *devm_gpiod_get_from_of_node(struct device *dev,
 	struct gpio_desc **dr;
 	struct gpio_desc *desc;
 
+	desc = gpiod_get_from_of_node(node, propname, index, dflags, label);
+	if (IS_ERR(desc))
+		return desc;
+
+	/*
+	 * For non-exclusive GPIO descriptors, check if this descriptor is
+	 * already under resource management by this device.
+	 */
+	if (dflags & GPIOD_FLAGS_BIT_NONEXCLUSIVE) {
+		struct devres *dres;
+
+		dres = devres_find(dev, devm_gpiod_release,
+				   devm_gpiod_match, &desc);
+		if (dres)
+			return desc;
+	}
+
 	dr = devres_alloc(devm_gpiod_release, sizeof(struct gpio_desc *),
 			  GFP_KERNEL);
-	if (!dr)
+	if (!dr) {
+		gpiod_put(desc);
 		return ERR_PTR(-ENOMEM);
-
-	desc = gpiod_get_from_of_node(node, propname, index, dflags, label);
-	if (IS_ERR(desc)) {
-		devres_free(dr);
-		return desc;
 	}
 
 	*dr = desc;
@@ -320,6 +346,36 @@ void devm_gpiod_put(struct device *dev, struct gpio_desc *desc)
 }
 EXPORT_SYMBOL(devm_gpiod_put);
 
+/**
+ * devm_gpiod_unhinge - Remove resource management from a gpio descriptor
+ * @dev:	GPIO consumer
+ * @desc:	GPIO descriptor to remove resource management from
+ *
+ * Remove resource management from a GPIO descriptor. This is needed when
+ * you want to hand over lifecycle management of a descriptor to another
+ * mechanism.
+ */
+
+void devm_gpiod_unhinge(struct device *dev, struct gpio_desc *desc)
+{
+	int ret;
+
+	if (IS_ERR_OR_NULL(desc))
+		return;
+	ret = devres_destroy(dev, devm_gpiod_release,
+			     devm_gpiod_match, &desc);
+	/*
+	 * If the GPIO descriptor is requested as nonexclusive, we
+	 * may call this function several times on the same descriptor
+	 * so it is OK if devres_destroy() returns -ENOENT.
+	 */
+	if (ret == -ENOENT)
+		return;
+	/* Anything else we should warn about */
+	WARN_ON(ret);
+}
+EXPORT_SYMBOL(devm_gpiod_unhinge);
+
 /**
  * devm_gpiod_put_array - Resource-managed gpiod_put_array()
  * @dev:	GPIO consumer

drivers/gpio/gpiolib.c

@@ -4205,6 +4205,8 @@ struct gpio_desc *gpiod_get_from_of_node(struct device_node *node,
 	transitory = flags & OF_GPIO_TRANSITORY;
 
 	ret = gpiod_request(desc, label);
+	if (ret == -EBUSY && (flags & GPIOD_FLAGS_BIT_NONEXCLUSIVE))
+		return desc;
 	if (ret)
 		return ERR_PTR(ret);
 

drivers/gpio/gpiolib.h

@@ -201,12 +201,6 @@ int gpiod_set_array_value_complex(bool raw, bool can_sleep,
 				  struct gpio_array *array_info,
 				  unsigned long *value_bitmap);
 
-/* This is just passed between gpiolib and devres */
-struct gpio_desc *gpiod_get_from_of_node(struct device_node *node,
-					 const char *propname, int index,
-					 enum gpiod_flags dflags,
-					 const char *label);
-
 extern struct spinlock gpio_lock;
 extern struct list_head gpio_devices;
 

drivers/mfd/axp20x.c

@@ -16,20 +16,21 @@
  * published by the Free Software Foundation.
  */
 
-#include <linux/err.h>
+#include <linux/acpi.h>
+#include <linux/bitops.h>
 #include <linux/delay.h>
+#include <linux/err.h>
 #include <linux/interrupt.h>
 #include <linux/kernel.h>
+#include <linux/mfd/axp20x.h>
+#include <linux/mfd/core.h>
 #include <linux/module.h>
+#include <linux/of_device.h>
 #include <linux/pm_runtime.h>
 #include <linux/regmap.h>
 #include <linux/regulator/consumer.h>
-#include <linux/mfd/axp20x.h>
-#include <linux/mfd/core.h>
-#include <linux/of_device.h>
-#include <linux/acpi.h>
 
-#define AXP20X_OFF	0x80
+#define AXP20X_OFF	BIT(7)
 
 #define AXP806_REG_ADDR_EXT_ADDR_MASTER_MODE	0
 #define AXP806_REG_ADDR_EXT_ADDR_SLAVE_MODE	BIT(4)

drivers/mfd/wm8994-core.c

@@ -21,7 +21,6 @@
 #include <linux/mfd/core.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
-#include <linux/of_gpio.h>
 #include <linux/pm_runtime.h>
 #include <linux/regmap.h>
 #include <linux/regulator/consumer.h>
@@ -306,14 +305,6 @@ static int wm8994_set_pdata_from_of(struct wm8994 *wm8994)
 
 	pdata->csnaddr_pd = of_property_read_bool(np, "wlf,csnaddr-pd");
 
-	pdata->ldo[0].enable = of_get_named_gpio(np, "wlf,ldo1ena", 0);
-	if (pdata->ldo[0].enable < 0)
-		pdata->ldo[0].enable = 0;
-
-	pdata->ldo[1].enable = of_get_named_gpio(np, "wlf,ldo2ena", 0);
-	if (pdata->ldo[1].enable < 0)
-		pdata->ldo[1].enable = 0;
-
 	return 0;
 }
 #else

drivers/regulator/88pm8607.c

@@ -328,7 +328,7 @@ static int pm8607_regulator_dt_init(struct platform_device *pdev,
 		return -ENODEV;
 	}
 	for_each_child_of_node(nproot, np) {
-		if (!of_node_cmp(np->name, info->desc.name)) {
+		if (of_node_name_eq(np, info->desc.name)) {
 			config->init_data =
 				of_get_regulator_init_data(&pdev->dev, np,
 							   &info->desc);

drivers/regulator/Kconfig

@@ -567,6 +567,16 @@ config REGULATOR_MC13892
 	  Say y here to support the regulators found on the Freescale MC13892
 	  PMIC.
 
+config REGULATOR_MCP16502
+	tristate "Microchip MCP16502 PMIC"
+	depends on I2C && OF
+	select REGMAP_I2C
+	help
+	  Say y here to support the MCP16502 PMIC. This driver supports
+	  basic operations (get/set voltage, get/set operating mode)
+	  through the regulator interface. In addition it enables
+	  suspend-to-ram/standby transition.
+
 config REGULATOR_MT6311
 	tristate "MediaTek MT6311 PMIC"
 	depends on I2C

drivers/regulator/Makefile

@@ -74,6 +74,7 @@ obj-$(CONFIG_REGULATOR_MAX77802) += max77802-regulator.o
 obj-$(CONFIG_REGULATOR_MC13783) += mc13783-regulator.o
 obj-$(CONFIG_REGULATOR_MC13892) += mc13892-regulator.o
 obj-$(CONFIG_REGULATOR_MC13XXX_CORE) +=  mc13xxx-regulator-core.o
+obj-$(CONFIG_REGULATOR_MCP16502) += mcp16502.o
 obj-$(CONFIG_REGULATOR_MT6311) += mt6311-regulator.o
 obj-$(CONFIG_REGULATOR_MT6323)	+= mt6323-regulator.o
 obj-$(CONFIG_REGULATOR_MT6380)	+= mt6380-regulator.o

drivers/regulator/act8945a-regulator.c

@@ -15,31 +15,41 @@
 #include <linux/module.h>
 #include <linux/of_device.h>
 #include <linux/platform_device.h>
+#include <linux/regmap.h>
 #include <linux/regulator/driver.h>
 #include <linux/regulator/machine.h>
+#include <dt-bindings/regulator/active-semi,8945a-regulator.h>
 
 /**
  * ACT8945A Global Register Map.
  */
 #define ACT8945A_SYS_MODE	0x00
 #define ACT8945A_SYS_CTRL	0x01
+#define ACT8945A_SYS_UNLK_REGS	0x0b
 #define ACT8945A_DCDC1_VSET1	0x20
 #define ACT8945A_DCDC1_VSET2	0x21
 #define ACT8945A_DCDC1_CTRL	0x22
+#define ACT8945A_DCDC1_SUS	0x24
 #define ACT8945A_DCDC2_VSET1	0x30
 #define ACT8945A_DCDC2_VSET2	0x31
 #define ACT8945A_DCDC2_CTRL	0x32
+#define ACT8945A_DCDC2_SUS	0x34
 #define ACT8945A_DCDC3_VSET1	0x40
 #define ACT8945A_DCDC3_VSET2	0x41
 #define ACT8945A_DCDC3_CTRL	0x42
+#define ACT8945A_DCDC3_SUS	0x44
 #define ACT8945A_LDO1_VSET	0x50
 #define ACT8945A_LDO1_CTRL	0x51
+#define ACT8945A_LDO1_SUS	0x52
 #define ACT8945A_LDO2_VSET	0x54
 #define ACT8945A_LDO2_CTRL	0x55
+#define ACT8945A_LDO2_SUS	0x56
 #define ACT8945A_LDO3_VSET	0x60
 #define ACT8945A_LDO3_CTRL	0x61
+#define ACT8945A_LDO3_SUS	0x62
 #define ACT8945A_LDO4_VSET	0x64
 #define ACT8945A_LDO4_CTRL	0x65
+#define ACT8945A_LDO4_SUS	0x66
 
 /**
  * Field Definitions.
@@ -60,7 +70,12 @@ enum {
 	ACT8945A_ID_LDO2,
 	ACT8945A_ID_LDO3,
 	ACT8945A_ID_LDO4,
-	ACT8945A_REG_NUM,
+	ACT8945A_ID_MAX,
+};
+
+struct act8945a_pmic {
+	struct regmap *regmap;
+	u32 op_mode[ACT8945A_ID_MAX];
 };
 
 static const struct regulator_linear_range act8945a_voltage_ranges[] = {
@@ -69,6 +84,143 @@ static const struct regulator_linear_range act8945a_voltage_ranges[] = {
 	REGULATOR_LINEAR_RANGE(2400000, 48, 63, 100000),
 };
 
+static int act8945a_set_suspend_state(struct regulator_dev *rdev, bool enable)
+{
+	struct regmap *regmap = rdev->regmap;
+	int id = rdev->desc->id, reg, val;
+
+	switch (id) {
+	case ACT8945A_ID_DCDC1:
+		reg = ACT8945A_DCDC1_SUS;
+		val = 0xa8;
+		break;
+	case ACT8945A_ID_DCDC2:
+		reg = ACT8945A_DCDC2_SUS;
+		val = 0xa8;
+		break;
+	case ACT8945A_ID_DCDC3:
+		reg = ACT8945A_DCDC3_SUS;
+		val = 0xa8;
+		break;
+	case ACT8945A_ID_LDO1:
+		reg = ACT8945A_LDO1_SUS;
+		val = 0xe8;
+		break;
+	case ACT8945A_ID_LDO2:
+		reg = ACT8945A_LDO2_SUS;
+		val = 0xe8;
+		break;
+	case ACT8945A_ID_LDO3:
+		reg = ACT8945A_LDO3_SUS;
+		val = 0xe8;
+		break;
+	case ACT8945A_ID_LDO4:
+		reg = ACT8945A_LDO4_SUS;
+		val = 0xe8;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	if (enable)
+		val |= BIT(4);
+
+	/*
+	 * Ask the PMIC to enable/disable this output when entering hibernate
+	 * mode.
+	 */
+	return regmap_write(regmap, reg, val);
+}
+
+static int act8945a_set_suspend_enable(struct regulator_dev *rdev)
+{
+	return act8945a_set_suspend_state(rdev, true);
+}
+
+static int act8945a_set_suspend_disable(struct regulator_dev *rdev)
+{
+	return act8945a_set_suspend_state(rdev, false);
+}
+
+static unsigned int act8945a_of_map_mode(unsigned int mode)
+{
+	switch (mode) {
+	case ACT8945A_REGULATOR_MODE_FIXED:
+	case ACT8945A_REGULATOR_MODE_NORMAL:
+		return REGULATOR_MODE_NORMAL;
+	case ACT8945A_REGULATOR_MODE_LOWPOWER:
+		return REGULATOR_MODE_STANDBY;
+	default:
+		return REGULATOR_MODE_INVALID;
+	}
+}
+
+static int act8945a_set_mode(struct regulator_dev *rdev, unsigned int mode)
+{
+	struct act8945a_pmic *act8945a = rdev_get_drvdata(rdev);
+	struct regmap *regmap = rdev->regmap;
+	int id = rdev->desc->id;
+	int reg, ret, val = 0;
+
+	switch (id) {
+	case ACT8945A_ID_DCDC1:
+		reg = ACT8945A_DCDC1_CTRL;
+		break;
+	case ACT8945A_ID_DCDC2:
+		reg = ACT8945A_DCDC2_CTRL;
+		break;
+	case ACT8945A_ID_DCDC3:
+		reg = ACT8945A_DCDC3_CTRL;
+		break;
+	case ACT8945A_ID_LDO1:
+		reg = ACT8945A_LDO1_SUS;
+		break;
+	case ACT8945A_ID_LDO2:
+		reg = ACT8945A_LDO2_SUS;
+		break;
+	case ACT8945A_ID_LDO3:
+		reg = ACT8945A_LDO3_SUS;
+		break;
+	case ACT8945A_ID_LDO4:
+		reg = ACT8945A_LDO4_SUS;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	switch (mode) {
+	case REGULATOR_MODE_STANDBY:
+		if (rdev->desc->id > ACT8945A_ID_DCDC3)
+			val = BIT(5);
+		break;
+	case REGULATOR_MODE_NORMAL:
+		if (rdev->desc->id <= ACT8945A_ID_DCDC3)
+			val = BIT(5);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	ret = regmap_update_bits(regmap, reg, BIT(5), val);
+	if (ret)
+		return ret;
+
+	act8945a->op_mode[id] = mode;
+
+	return 0;
+}
+
+static unsigned int act8945a_get_mode(struct regulator_dev *rdev)
+{
+	struct act8945a_pmic *act8945a = rdev_get_drvdata(rdev);
+	int id = rdev->desc->id;
+
+	if (id < ACT8945A_ID_DCDC1 || id >= ACT8945A_ID_MAX)
+		return -EINVAL;
+
+	return act8945a->op_mode[id];
+}
+
 static const struct regulator_ops act8945a_ops = {
 	.list_voltage		= regulator_list_voltage_linear_range,
 	.map_voltage		= regulator_map_voltage_linear_range,
@@ -76,7 +228,11 @@ static const struct regulator_ops act8945a_ops = {
 	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
 	.enable			= regulator_enable_regmap,
 	.disable		= regulator_disable_regmap,
+	.set_mode		= act8945a_set_mode,
+	.get_mode		= act8945a_get_mode,
 	.is_enabled		= regulator_is_enabled_regmap,
+	.set_suspend_enable	= act8945a_set_suspend_enable,
+	.set_suspend_disable	= act8945a_set_suspend_disable,
 };
 
 #define ACT89xx_REG(_name, _family, _id, _vsel_reg, _supply)		\
@@ -84,6 +240,7 @@ static const struct regulator_ops act8945a_ops = {
 		.name			= _name,			\
 		.supply_name		= _supply,			\
 		.of_match		= of_match_ptr("REG_"#_id),	\
+		.of_map_mode		= act8945a_of_map_mode,		\
 		.regulators_node	= of_match_ptr("regulators"),	\
 		.id			= _family##_ID_##_id,		\
 		.type			= REGULATOR_VOLTAGE,		\
@@ -122,10 +279,22 @@ static int act8945a_pmic_probe(struct platform_device *pdev)
 {
 	struct regulator_config config = { };
 	const struct regulator_desc *regulators;
+	struct act8945a_pmic *act8945a;
 	struct regulator_dev *rdev;
 	int i, num_regulators;
 	bool voltage_select;
 
+	act8945a = devm_kzalloc(&pdev->dev, sizeof(*act8945a), GFP_KERNEL);
+	if (!act8945a)
+		return -ENOMEM;
+
+	act8945a->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+	if (!act8945a->regmap) {
+		dev_err(&pdev->dev,
+			"could not retrieve regmap from parent device\n");
+		return -EINVAL;
+	}
+
 	voltage_select = of_property_read_bool(pdev->dev.parent->of_node,
 					       "active-semi,vsel-high");
 
@@ -139,8 +308,10 @@ static int act8945a_pmic_probe(struct platform_device *pdev)
 
 	config.dev = &pdev->dev;
 	config.dev->of_node = pdev->dev.parent->of_node;
+	config.driver_data = act8945a;
 	for (i = 0; i < num_regulators; i++) {
-		rdev = devm_regulator_register(&pdev->dev, &regulators[i], &config);
+		rdev = devm_regulator_register(&pdev->dev, &regulators[i],
+					       &config);
 		if (IS_ERR(rdev)) {
 			dev_err(&pdev->dev,
 				"failed to register %s regulator\n",
@@ -149,14 +320,42 @@ static int act8945a_pmic_probe(struct platform_device *pdev)
 		}
 	}
 
-	return 0;
+	platform_set_drvdata(pdev, act8945a);
+
+	/* Unlock expert registers. */
+	return regmap_write(act8945a->regmap, ACT8945A_SYS_UNLK_REGS, 0xef);
+}
+
+static int __maybe_unused act8945a_suspend(struct device *pdev)
+{
+	struct act8945a_pmic *act8945a = dev_get_drvdata(pdev);
+
+	/*
+	 * Ask the PMIC to enter the suspend mode on the next PWRHLD
+	 * transition.
+	 */
+	return regmap_write(act8945a->regmap, ACT8945A_SYS_CTRL, 0x42);
+}
+
+static SIMPLE_DEV_PM_OPS(act8945a_pm, act8945a_suspend, NULL);
+
+static void act8945a_pmic_shutdown(struct platform_device *pdev)
+{
+	struct act8945a_pmic *act8945a = platform_get_drvdata(pdev);
+
+	/*
+	 * Ask the PMIC to shutdown everything on the next PWRHLD transition.
+	 */
+	regmap_write(act8945a->regmap, ACT8945A_SYS_CTRL, 0x0);
 }
 
 static struct platform_driver act8945a_pmic_driver = {
 	.driver = {
 		.name = "act8945a-regulator",
+		.pm = &act8945a_pm,
 	},
 	.probe = act8945a_pmic_probe,
+	.shutdown = act8945a_pmic_shutdown,
 };
 module_platform_driver(act8945a_pmic_driver);
 

drivers/regulator/arizona-ldo1.c

@@ -283,9 +283,6 @@ static int arizona_ldo1_common_init(struct platform_device *pdev,
 	of_node_put(config.of_node);
 
 	if (IS_ERR(ldo1->regulator)) {
-		if (config.ena_gpiod)
-			gpiod_put(config.ena_gpiod);
-
 		ret = PTR_ERR(ldo1->regulator);
 		dev_err(&pdev->dev, "Failed to register LDO1 supply: %d\n",
 			ret);

drivers/regulator/as3711-regulator.c

+// SPDX-License-Identifier: GPL-2.0
 /*
  * AS3711 PMIC regulator driver, using DCDC Step Down and LDO supplies
  *
  * Copyright (C) 2012 Renesas Electronics Corporation
  * Author: Guennadi Liakhovetski, <g.liakhovetski@gmx.de>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the version 2 of the GNU General Public License as
- * published by the Free Software Foundation
  */
 
 #include <linux/err.h>

drivers/regulator/axp20x-regulator.c

@@ -13,31 +13,262 @@
  * GNU General Public License for more details.
  */
 
+#include <linux/bitops.h>
+#include <linux/delay.h>
 #include <linux/err.h>
 #include <linux/init.h>
+#include <linux/mfd/axp20x.h>
 #include <linux/module.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/regmap.h>
-#include <linux/mfd/axp20x.h>
 #include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
 #include <linux/regulator/of_regulator.h>
 
+#define AXP20X_GPIO0_FUNC_MASK		GENMASK(3, 0)
+#define AXP20X_GPIO1_FUNC_MASK		GENMASK(3, 0)
+
 #define AXP20X_IO_ENABLED		0x03
 #define AXP20X_IO_DISABLED		0x07
 
+#define AXP20X_WORKMODE_DCDC2_MASK	BIT_MASK(2)
+#define AXP20X_WORKMODE_DCDC3_MASK	BIT_MASK(1)
+
+#define AXP20X_FREQ_DCDC_MASK		GENMASK(3, 0)
+
+#define AXP20X_VBUS_IPSOUT_MGMT_MASK	BIT_MASK(2)
+
+#define AXP20X_DCDC2_V_OUT_MASK		GENMASK(5, 0)
+#define AXP20X_DCDC3_V_OUT_MASK		GENMASK(7, 0)
+#define AXP20X_LDO24_V_OUT_MASK		GENMASK(7, 4)
+#define AXP20X_LDO3_V_OUT_MASK		GENMASK(6, 0)
+#define AXP20X_LDO5_V_OUT_MASK		GENMASK(7, 4)
+
+#define AXP20X_PWR_OUT_EXTEN_MASK	BIT_MASK(0)
+#define AXP20X_PWR_OUT_DCDC3_MASK	BIT_MASK(1)
+#define AXP20X_PWR_OUT_LDO2_MASK	BIT_MASK(2)
+#define AXP20X_PWR_OUT_LDO4_MASK	BIT_MASK(3)
+#define AXP20X_PWR_OUT_DCDC2_MASK	BIT_MASK(4)
+#define AXP20X_PWR_OUT_LDO3_MASK	BIT_MASK(6)
+
+#define AXP20X_DCDC2_LDO3_V_RAMP_DCDC2_RATE_MASK	BIT_MASK(0)
+#define AXP20X_DCDC2_LDO3_V_RAMP_DCDC2_RATE(x) \
+	((x) << 0)
+#define AXP20X_DCDC2_LDO3_V_RAMP_LDO3_RATE_MASK		BIT_MASK(1)
+#define AXP20X_DCDC2_LDO3_V_RAMP_LDO3_RATE(x) \
+	((x) << 1)
+#define AXP20X_DCDC2_LDO3_V_RAMP_DCDC2_EN_MASK		BIT_MASK(2)
+#define AXP20X_DCDC2_LDO3_V_RAMP_DCDC2_EN		BIT(2)
+#define AXP20X_DCDC2_LDO3_V_RAMP_LDO3_EN_MASK		BIT_MASK(3)
+#define AXP20X_DCDC2_LDO3_V_RAMP_LDO3_EN		BIT(3)
+
+#define AXP20X_LDO4_V_OUT_1250mV_START	0x0
+#define AXP20X_LDO4_V_OUT_1250mV_STEPS	0
+#define AXP20X_LDO4_V_OUT_1250mV_END	\
+	(AXP20X_LDO4_V_OUT_1250mV_START + AXP20X_LDO4_V_OUT_1250mV_STEPS)
+#define AXP20X_LDO4_V_OUT_1300mV_START	0x1
+#define AXP20X_LDO4_V_OUT_1300mV_STEPS	7
+#define AXP20X_LDO4_V_OUT_1300mV_END	\
+	(AXP20X_LDO4_V_OUT_1300mV_START + AXP20X_LDO4_V_OUT_1300mV_STEPS)
+#define AXP20X_LDO4_V_OUT_2500mV_START	0x9
+#define AXP20X_LDO4_V_OUT_2500mV_STEPS	0
+#define AXP20X_LDO4_V_OUT_2500mV_END	\
+	(AXP20X_LDO4_V_OUT_2500mV_START + AXP20X_LDO4_V_OUT_2500mV_STEPS)
+#define AXP20X_LDO4_V_OUT_2700mV_START	0xa
+#define AXP20X_LDO4_V_OUT_2700mV_STEPS	1
+#define AXP20X_LDO4_V_OUT_2700mV_END	\
+	(AXP20X_LDO4_V_OUT_2700mV_START + AXP20X_LDO4_V_OUT_2700mV_STEPS)
+#define AXP20X_LDO4_V_OUT_3000mV_START	0xc
+#define AXP20X_LDO4_V_OUT_3000mV_STEPS	3
+#define AXP20X_LDO4_V_OUT_3000mV_END	\
+	(AXP20X_LDO4_V_OUT_3000mV_START + AXP20X_LDO4_V_OUT_3000mV_STEPS)
+#define AXP20X_LDO4_V_OUT_NUM_VOLTAGES	16
+
 #define AXP22X_IO_ENABLED		0x03
 #define AXP22X_IO_DISABLED		0x04
 
-#define AXP20X_WORKMODE_DCDC2_MASK	BIT(2)
-#define AXP20X_WORKMODE_DCDC3_MASK	BIT(1)
-#define AXP22X_WORKMODE_DCDCX_MASK(x)	BIT(x)
-
-#define AXP20X_FREQ_DCDC_MASK		0x0f
+#define AXP22X_WORKMODE_DCDCX_MASK(x)	BIT_MASK(x)
 
 #define AXP22X_MISC_N_VBUSEN_FUNC	BIT(4)
 
+#define AXP22X_DCDC1_V_OUT_MASK		GENMASK(4, 0)
+#define AXP22X_DCDC2_V_OUT_MASK		GENMASK(5, 0)
+#define AXP22X_DCDC3_V_OUT_MASK		GENMASK(5, 0)
+#define AXP22X_DCDC4_V_OUT_MASK		GENMASK(5, 0)
+#define AXP22X_DCDC5_V_OUT_MASK		GENMASK(4, 0)
+#define AXP22X_DC5LDO_V_OUT_MASK	GENMASK(2, 0)
+#define AXP22X_ALDO1_V_OUT_MASK		GENMASK(4, 0)
+#define AXP22X_ALDO2_V_OUT_MASK		GENMASK(4, 0)
+#define AXP22X_ALDO3_V_OUT_MASK		GENMASK(4, 0)
+#define AXP22X_DLDO1_V_OUT_MASK		GENMASK(4, 0)
+#define AXP22X_DLDO2_V_OUT_MASK		GENMASK(4, 0)
+#define AXP22X_DLDO3_V_OUT_MASK		GENMASK(4, 0)
+#define AXP22X_DLDO4_V_OUT_MASK		GENMASK(4, 0)
+#define AXP22X_ELDO1_V_OUT_MASK		GENMASK(4, 0)
+#define AXP22X_ELDO2_V_OUT_MASK		GENMASK(4, 0)
+#define AXP22X_ELDO3_V_OUT_MASK		GENMASK(4, 0)
+#define AXP22X_LDO_IO0_V_OUT_MASK	GENMASK(4, 0)
+#define AXP22X_LDO_IO1_V_OUT_MASK	GENMASK(4, 0)
+
+#define AXP22X_PWR_OUT_DC5LDO_MASK	BIT_MASK(0)
+#define AXP22X_PWR_OUT_DCDC1_MASK	BIT_MASK(1)
+#define AXP22X_PWR_OUT_DCDC2_MASK	BIT_MASK(2)
+#define AXP22X_PWR_OUT_DCDC3_MASK	BIT_MASK(3)
+#define AXP22X_PWR_OUT_DCDC4_MASK	BIT_MASK(4)
+#define AXP22X_PWR_OUT_DCDC5_MASK	BIT_MASK(5)
+#define AXP22X_PWR_OUT_ALDO1_MASK	BIT_MASK(6)
+#define AXP22X_PWR_OUT_ALDO2_MASK	BIT_MASK(7)
+
+#define AXP22X_PWR_OUT_SW_MASK		BIT_MASK(6)
+#define AXP22X_PWR_OUT_DC1SW_MASK	BIT_MASK(7)
+
+#define AXP22X_PWR_OUT_ELDO1_MASK	BIT_MASK(0)
+#define AXP22X_PWR_OUT_ELDO2_MASK	BIT_MASK(1)
+#define AXP22X_PWR_OUT_ELDO3_MASK	BIT_MASK(2)
+#define AXP22X_PWR_OUT_DLDO1_MASK	BIT_MASK(3)
+#define AXP22X_PWR_OUT_DLDO2_MASK	BIT_MASK(4)
+#define AXP22X_PWR_OUT_DLDO3_MASK	BIT_MASK(5)
+#define AXP22X_PWR_OUT_DLDO4_MASK	BIT_MASK(6)
+#define AXP22X_PWR_OUT_ALDO3_MASK	BIT_MASK(7)
+
+#define AXP803_PWR_OUT_DCDC1_MASK	BIT_MASK(0)
+#define AXP803_PWR_OUT_DCDC2_MASK	BIT_MASK(1)
+#define AXP803_PWR_OUT_DCDC3_MASK	BIT_MASK(2)
+#define AXP803_PWR_OUT_DCDC4_MASK	BIT_MASK(3)
+#define AXP803_PWR_OUT_DCDC5_MASK	BIT_MASK(4)
+#define AXP803_PWR_OUT_DCDC6_MASK	BIT_MASK(5)
+
+#define AXP803_PWR_OUT_FLDO1_MASK	BIT_MASK(2)
+#define AXP803_PWR_OUT_FLDO2_MASK	BIT_MASK(3)
+
+#define AXP803_DCDC1_V_OUT_MASK		GENMASK(4, 0)
+#define AXP803_DCDC2_V_OUT_MASK		GENMASK(6, 0)
+#define AXP803_DCDC3_V_OUT_MASK		GENMASK(6, 0)
+#define AXP803_DCDC4_V_OUT_MASK		GENMASK(6, 0)
+#define AXP803_DCDC5_V_OUT_MASK		GENMASK(6, 0)
+#define AXP803_DCDC6_V_OUT_MASK		GENMASK(6, 0)
+
+#define AXP803_FLDO1_V_OUT_MASK		GENMASK(3, 0)
+#define AXP803_FLDO2_V_OUT_MASK		GENMASK(3, 0)
+
+#define AXP803_DCDC23_POLYPHASE_DUAL	BIT(6)
+#define AXP803_DCDC56_POLYPHASE_DUAL	BIT(5)
+
+#define AXP803_DCDC234_500mV_START	0x00
+#define AXP803_DCDC234_500mV_STEPS	70
+#define AXP803_DCDC234_500mV_END	\
+	(AXP803_DCDC234_500mV_START + AXP803_DCDC234_500mV_STEPS)
+#define AXP803_DCDC234_1220mV_START	0x47
+#define AXP803_DCDC234_1220mV_STEPS	4
+#define AXP803_DCDC234_1220mV_END	\
+	(AXP803_DCDC234_1220mV_START + AXP803_DCDC234_1220mV_STEPS)
+#define AXP803_DCDC234_NUM_VOLTAGES	76
+
+#define AXP803_DCDC5_800mV_START	0x00
+#define AXP803_DCDC5_800mV_STEPS	32
+#define AXP803_DCDC5_800mV_END		\
+	(AXP803_DCDC5_800mV_START + AXP803_DCDC5_800mV_STEPS)
+#define AXP803_DCDC5_1140mV_START	0x21
+#define AXP803_DCDC5_1140mV_STEPS	35
+#define AXP803_DCDC5_1140mV_END		\
+	(AXP803_DCDC5_1140mV_START + AXP803_DCDC5_1140mV_STEPS)
+#define AXP803_DCDC5_NUM_VOLTAGES	68
+
+#define AXP803_DCDC6_600mV_START	0x00
+#define AXP803_DCDC6_600mV_STEPS	50
+#define AXP803_DCDC6_600mV_END		\
+	(AXP803_DCDC6_600mV_START + AXP803_DCDC6_600mV_STEPS)
+#define AXP803_DCDC6_1120mV_START	0x33
+#define AXP803_DCDC6_1120mV_STEPS	14
+#define AXP803_DCDC6_1120mV_END		\
+	(AXP803_DCDC6_1120mV_START + AXP803_DCDC6_1120mV_STEPS)
+#define AXP803_DCDC6_NUM_VOLTAGES	72
+
+#define AXP803_DLDO2_700mV_START	0x00
+#define AXP803_DLDO2_700mV_STEPS	26
+#define AXP803_DLDO2_700mV_END		\
+	(AXP803_DLDO2_700mV_START + AXP803_DLDO2_700mV_STEPS)
+#define AXP803_DLDO2_3400mV_START	0x1b
+#define AXP803_DLDO2_3400mV_STEPS	4
+#define AXP803_DLDO2_3400mV_END		\
+	(AXP803_DLDO2_3400mV_START + AXP803_DLDO2_3400mV_STEPS)
+#define AXP803_DLDO2_NUM_VOLTAGES	32
+
+#define AXP806_DCDCA_V_CTRL_MASK	GENMASK(6, 0)
+#define AXP806_DCDCB_V_CTRL_MASK	GENMASK(4, 0)
+#define AXP806_DCDCC_V_CTRL_MASK	GENMASK(6, 0)
+#define AXP806_DCDCD_V_CTRL_MASK	GENMASK(5, 0)
+#define AXP806_DCDCE_V_CTRL_MASK	GENMASK(4, 0)
+#define AXP806_ALDO1_V_CTRL_MASK	GENMASK(4, 0)
+#define AXP806_ALDO2_V_CTRL_MASK	GENMASK(4, 0)
+#define AXP806_ALDO3_V_CTRL_MASK	GENMASK(4, 0)
+#define AXP806_BLDO1_V_CTRL_MASK	GENMASK(3, 0)
+#define AXP806_BLDO2_V_CTRL_MASK	GENMASK(3, 0)
+#define AXP806_BLDO3_V_CTRL_MASK	GENMASK(3, 0)
+#define AXP806_BLDO4_V_CTRL_MASK	GENMASK(3, 0)
+#define AXP806_CLDO1_V_CTRL_MASK	GENMASK(4, 0)
+#define AXP806_CLDO2_V_CTRL_MASK	GENMASK(4, 0)
+#define AXP806_CLDO3_V_CTRL_MASK	GENMASK(4, 0)
+
+#define AXP806_PWR_OUT_DCDCA_MASK	BIT_MASK(0)
+#define AXP806_PWR_OUT_DCDCB_MASK	BIT_MASK(1)
+#define AXP806_PWR_OUT_DCDCC_MASK	BIT_MASK(2)
+#define AXP806_PWR_OUT_DCDCD_MASK	BIT_MASK(3)
+#define AXP806_PWR_OUT_DCDCE_MASK	BIT_MASK(4)
+#define AXP806_PWR_OUT_ALDO1_MASK	BIT_MASK(5)
+#define AXP806_PWR_OUT_ALDO2_MASK	BIT_MASK(6)
+#define AXP806_PWR_OUT_ALDO3_MASK	BIT_MASK(7)
+#define AXP806_PWR_OUT_BLDO1_MASK	BIT_MASK(0)
+#define AXP806_PWR_OUT_BLDO2_MASK	BIT_MASK(1)
+#define AXP806_PWR_OUT_BLDO3_MASK	BIT_MASK(2)
+#define AXP806_PWR_OUT_BLDO4_MASK	BIT_MASK(3)
+#define AXP806_PWR_OUT_CLDO1_MASK	BIT_MASK(4)
+#define AXP806_PWR_OUT_CLDO2_MASK	BIT_MASK(5)
+#define AXP806_PWR_OUT_CLDO3_MASK	BIT_MASK(6)
+#define AXP806_PWR_OUT_SW_MASK		BIT_MASK(7)
+
+#define AXP806_DCDCAB_POLYPHASE_DUAL	0x40
+#define AXP806_DCDCABC_POLYPHASE_TRI	0x80
+#define AXP806_DCDCABC_POLYPHASE_MASK	GENMASK(7, 6)
+
+#define AXP806_DCDCDE_POLYPHASE_DUAL	BIT(5)
+
+#define AXP806_DCDCA_600mV_START	0x00
+#define AXP806_DCDCA_600mV_STEPS	50
+#define AXP806_DCDCA_600mV_END		\
+	(AXP806_DCDCA_600mV_START + AXP806_DCDCA_600mV_STEPS)
+#define AXP806_DCDCA_1120mV_START	0x33
+#define AXP806_DCDCA_1120mV_STEPS	14
+#define AXP806_DCDCA_1120mV_END		\
+	(AXP806_DCDCA_1120mV_START + AXP806_DCDCA_1120mV_STEPS)
+#define AXP806_DCDCA_NUM_VOLTAGES	72
+
+#define AXP806_DCDCD_600mV_START	0x00
+#define AXP806_DCDCD_600mV_STEPS	45
+#define AXP806_DCDCD_600mV_END		\
+	(AXP806_DCDCD_600mV_START + AXP806_DCDCD_600mV_STEPS)
+#define AXP806_DCDCD_1600mV_START	0x2e
+#define AXP806_DCDCD_1600mV_STEPS	17
+#define AXP806_DCDCD_1600mV_END		\
+	(AXP806_DCDCD_1600mV_START + AXP806_DCDCD_1600mV_STEPS)
+#define AXP806_DCDCD_NUM_VOLTAGES	64
+
+#define AXP809_DCDC4_600mV_START	0x00
+#define AXP809_DCDC4_600mV_STEPS	47
+#define AXP809_DCDC4_600mV_END		\
+	(AXP809_DCDC4_600mV_START + AXP809_DCDC4_600mV_STEPS)
+#define AXP809_DCDC4_1800mV_START	0x30
+#define AXP809_DCDC4_1800mV_STEPS	8
+#define AXP809_DCDC4_1800mV_END		\
+	(AXP809_DCDC4_1800mV_START + AXP809_DCDC4_1800mV_STEPS)
+#define AXP809_DCDC4_NUM_VOLTAGES	57
+
+#define AXP813_DCDC7_V_OUT_MASK		GENMASK(6, 0)
+
+#define AXP813_PWR_OUT_DCDC7_MASK	BIT_MASK(6)
+
 #define AXP_DESC_IO(_family, _id, _match, _supply, _min, _max, _step, _vreg,	\
 		    _vmask, _ereg, _emask, _enable_val, _disable_val)		\
 	[_family##_##_id] = {							\
@@ -128,6 +359,133 @@
 		.ops		= &axp20x_ops_range,				\
 	}
 
+static const int axp209_dcdc2_ldo3_slew_rates[] = {
+	1600,
+	 800,
+};
+
+static int axp20x_set_ramp_delay(struct regulator_dev *rdev, int ramp)
+{
+	struct axp20x_dev *axp20x = rdev_get_drvdata(rdev);
+	const struct regulator_desc *desc = rdev->desc;
+	u8 reg, mask, enable, cfg = 0xff;
+	const int *slew_rates;
+	int rate_count = 0;
+
+	if (!rdev)
+		return -EINVAL;
+
+	switch (axp20x->variant) {
+	case AXP209_ID:
+		if (desc->id == AXP20X_DCDC2) {
+			slew_rates = axp209_dcdc2_ldo3_slew_rates;
+			rate_count = ARRAY_SIZE(axp209_dcdc2_ldo3_slew_rates);
+			reg = AXP20X_DCDC2_LDO3_V_RAMP;
+			mask = AXP20X_DCDC2_LDO3_V_RAMP_DCDC2_RATE_MASK |
+			       AXP20X_DCDC2_LDO3_V_RAMP_DCDC2_EN_MASK;
+			enable = (ramp > 0) ?
+				 AXP20X_DCDC2_LDO3_V_RAMP_DCDC2_EN :
+				 !AXP20X_DCDC2_LDO3_V_RAMP_DCDC2_EN;
+			break;
+		}
+
+		if (desc->id == AXP20X_LDO3) {
+			slew_rates = axp209_dcdc2_ldo3_slew_rates;
+			rate_count = ARRAY_SIZE(axp209_dcdc2_ldo3_slew_rates);
+			reg = AXP20X_DCDC2_LDO3_V_RAMP;
+			mask = AXP20X_DCDC2_LDO3_V_RAMP_LDO3_RATE_MASK |
+			       AXP20X_DCDC2_LDO3_V_RAMP_LDO3_EN_MASK;
+			enable = (ramp > 0) ?
+				 AXP20X_DCDC2_LDO3_V_RAMP_LDO3_EN :
+				 !AXP20X_DCDC2_LDO3_V_RAMP_LDO3_EN;
+			break;
+		}
+
+		if (rate_count > 0)
+			break;
+
+		/* fall through */
+	default:
+		/* Not supported for this regulator */
+		return -ENOTSUPP;
+	}
+
+	if (ramp == 0) {
+		cfg = enable;
+	} else {
+		int i;
+
+		for (i = 0; i < rate_count; i++) {
+			if (ramp <= slew_rates[i])
+				cfg = AXP20X_DCDC2_LDO3_V_RAMP_LDO3_RATE(i);
+			else
+				break;
+		}
+
+		if (cfg == 0xff) {
+			dev_err(axp20x->dev, "unsupported ramp value %d", ramp);
+			return -EINVAL;
+		}
+
+		cfg |= enable;
+	}
+
+	return regmap_update_bits(axp20x->regmap, reg, mask, cfg);
+}
+
+static int axp20x_regulator_enable_regmap(struct regulator_dev *rdev)
+{
+	struct axp20x_dev *axp20x = rdev_get_drvdata(rdev);
+	const struct regulator_desc *desc = rdev->desc;
+
+	if (!rdev)
+		return -EINVAL;
+
+	switch (axp20x->variant) {
+	case AXP209_ID:
+		if ((desc->id == AXP20X_LDO3) &&
+		    rdev->constraints && rdev->constraints->soft_start) {
+			int v_out;
+			int ret;
+
+			/*
+			 * On some boards, the LDO3 can be overloaded when
+			 * turning on, causing the entire PMIC to shutdown
+			 * without warning. Turning it on at the minimal voltage
+			 * and then setting the voltage to the requested value
+			 * works reliably.
+			 */
+			if (regulator_is_enabled_regmap(rdev))
+				break;
+
+			v_out = regulator_get_voltage_sel_regmap(rdev);
+			if (v_out < 0)
+				return v_out;
+
+			if (v_out == 0)
+				break;
+
+			ret = regulator_set_voltage_sel_regmap(rdev, 0x00);
+			/*
+			 * A small pause is needed between
+			 * setting the voltage and enabling the LDO to give the
+			 * internal state machine time to process the request.
+			 */
+			usleep_range(1000, 5000);
+			ret |= regulator_enable_regmap(rdev);
+			ret |= regulator_set_voltage_sel_regmap(rdev, v_out);
+
+			return ret;
+		}
+		break;
+	default:
+		/* No quirks */
+		break;
+	}
+
+	return regulator_enable_regmap(rdev);
+};
+
 static const struct regulator_ops axp20x_ops_fixed = {
 	.list_voltage		= regulator_list_voltage_linear,
 };
@@ -145,9 +503,10 @@ static const struct regulator_ops axp20x_ops = {
 	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
 	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
 	.list_voltage		= regulator_list_voltage_linear,
-	.enable			= regulator_enable_regmap,
+	.enable			= axp20x_regulator_enable_regmap,
 	.disable		= regulator_disable_regmap,
 	.is_enabled		= regulator_is_enabled_regmap,
+	.set_ramp_delay		= axp20x_set_ramp_delay,
 };
 
 static const struct regulator_ops axp20x_ops_sw = {
@@ -157,77 +516,116 @@ static const struct regulator_ops axp20x_ops_sw = {
 };
 
 static const struct regulator_linear_range axp20x_ldo4_ranges[] = {
-	REGULATOR_LINEAR_RANGE(1250000, 0x0, 0x0, 0),
-	REGULATOR_LINEAR_RANGE(1300000, 0x1, 0x8, 100000),
-	REGULATOR_LINEAR_RANGE(2500000, 0x9, 0x9, 0),
-	REGULATOR_LINEAR_RANGE(2700000, 0xa, 0xb, 100000),
-	REGULATOR_LINEAR_RANGE(3000000, 0xc, 0xf, 100000),
+	REGULATOR_LINEAR_RANGE(1250000,
+			       AXP20X_LDO4_V_OUT_1250mV_START,
+			       AXP20X_LDO4_V_OUT_1250mV_END,
+			       0),
+	REGULATOR_LINEAR_RANGE(1300000,
+			       AXP20X_LDO4_V_OUT_1300mV_START,
+			       AXP20X_LDO4_V_OUT_1300mV_END,
+			       100000),
+	REGULATOR_LINEAR_RANGE(2500000,
+			       AXP20X_LDO4_V_OUT_2500mV_START,
+			       AXP20X_LDO4_V_OUT_2500mV_END,
+			       0),
+	REGULATOR_LINEAR_RANGE(2700000,
+			       AXP20X_LDO4_V_OUT_2700mV_START,
+			       AXP20X_LDO4_V_OUT_2700mV_END,
+			       100000),
+	REGULATOR_LINEAR_RANGE(3000000,
+			       AXP20X_LDO4_V_OUT_3000mV_START,
+			       AXP20X_LDO4_V_OUT_3000mV_END,
+			       100000),
 };
 
 static const struct regulator_desc axp20x_regulators[] = {
 	AXP_DESC(AXP20X, DCDC2, "dcdc2", "vin2", 700, 2275, 25,
-		 AXP20X_DCDC2_V_OUT, 0x3f, AXP20X_PWR_OUT_CTRL, 0x10),
+		 AXP20X_DCDC2_V_OUT, AXP20X_DCDC2_V_OUT_MASK,
+		 AXP20X_PWR_OUT_CTRL, AXP20X_PWR_OUT_DCDC2_MASK),
 	AXP_DESC(AXP20X, DCDC3, "dcdc3", "vin3", 700, 3500, 25,
-		 AXP20X_DCDC3_V_OUT, 0x7f, AXP20X_PWR_OUT_CTRL, 0x02),
+		 AXP20X_DCDC3_V_OUT, AXP20X_DCDC3_V_OUT_MASK,
+		 AXP20X_PWR_OUT_CTRL, AXP20X_PWR_OUT_DCDC3_MASK),
 	AXP_DESC_FIXED(AXP20X, LDO1, "ldo1", "acin", 1300),
 	AXP_DESC(AXP20X, LDO2, "ldo2", "ldo24in", 1800, 3300, 100,
-		 AXP20X_LDO24_V_OUT, 0xf0, AXP20X_PWR_OUT_CTRL, 0x04),
+		 AXP20X_LDO24_V_OUT, AXP20X_LDO24_V_OUT_MASK,
+		 AXP20X_PWR_OUT_CTRL, AXP20X_PWR_OUT_LDO2_MASK),
 	AXP_DESC(AXP20X, LDO3, "ldo3", "ldo3in", 700, 3500, 25,
-		 AXP20X_LDO3_V_OUT, 0x7f, AXP20X_PWR_OUT_CTRL, 0x40),
-	AXP_DESC_RANGES(AXP20X, LDO4, "ldo4", "ldo24in", axp20x_ldo4_ranges,
-			16, AXP20X_LDO24_V_OUT, 0x0f, AXP20X_PWR_OUT_CTRL,
-			0x08),
+		 AXP20X_LDO3_V_OUT, AXP20X_LDO3_V_OUT_MASK,
+		 AXP20X_PWR_OUT_CTRL, AXP20X_PWR_OUT_LDO3_MASK),
+	AXP_DESC_RANGES(AXP20X, LDO4, "ldo4", "ldo24in",
+			axp20x_ldo4_ranges, AXP20X_LDO4_V_OUT_NUM_VOLTAGES,
+			AXP20X_LDO24_V_OUT, AXP20X_LDO24_V_OUT_MASK,
+			AXP20X_PWR_OUT_CTRL, AXP20X_PWR_OUT_LDO4_MASK),
 	AXP_DESC_IO(AXP20X, LDO5, "ldo5", "ldo5in", 1800, 3300, 100,
-		    AXP20X_LDO5_V_OUT, 0xf0, AXP20X_GPIO0_CTRL, 0x07,
+		    AXP20X_LDO5_V_OUT, AXP20X_LDO5_V_OUT_MASK,
+		    AXP20X_GPIO0_CTRL, AXP20X_GPIO0_FUNC_MASK,
 		    AXP20X_IO_ENABLED, AXP20X_IO_DISABLED),
 };
 
 static const struct regulator_desc axp22x_regulators[] = {
 	AXP_DESC(AXP22X, DCDC1, "dcdc1", "vin1", 1600, 3400, 100,
-		 AXP22X_DCDC1_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL1, BIT(1)),
+		 AXP22X_DCDC1_V_OUT, AXP22X_DCDC1_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL1, AXP22X_PWR_OUT_DCDC1_MASK),
 	AXP_DESC(AXP22X, DCDC2, "dcdc2", "vin2", 600, 1540, 20,
-		 AXP22X_DCDC2_V_OUT, 0x3f, AXP22X_PWR_OUT_CTRL1, BIT(2)),
+		 AXP22X_DCDC2_V_OUT, AXP22X_DCDC2_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL1, AXP22X_PWR_OUT_DCDC2_MASK),
 	AXP_DESC(AXP22X, DCDC3, "dcdc3", "vin3", 600, 1860, 20,
-		 AXP22X_DCDC3_V_OUT, 0x3f, AXP22X_PWR_OUT_CTRL1, BIT(3)),
+		 AXP22X_DCDC3_V_OUT, AXP22X_DCDC3_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL1, AXP22X_PWR_OUT_DCDC3_MASK),
 	AXP_DESC(AXP22X, DCDC4, "dcdc4", "vin4", 600, 1540, 20,
-		 AXP22X_DCDC4_V_OUT, 0x3f, AXP22X_PWR_OUT_CTRL1, BIT(4)),
+		 AXP22X_DCDC4_V_OUT, AXP22X_DCDC4_V_OUT,
+		 AXP22X_PWR_OUT_CTRL1, AXP22X_PWR_OUT_DCDC4_MASK),
 	AXP_DESC(AXP22X, DCDC5, "dcdc5", "vin5", 1000, 2550, 50,
-		 AXP22X_DCDC5_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL1, BIT(5)),
+		 AXP22X_DCDC5_V_OUT, AXP22X_DCDC5_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL1, AXP22X_PWR_OUT_DCDC5_MASK),
 	/* secondary switchable output of DCDC1 */
-	AXP_DESC_SW(AXP22X, DC1SW, "dc1sw", NULL, AXP22X_PWR_OUT_CTRL2,
-		    BIT(7)),
+	AXP_DESC_SW(AXP22X, DC1SW, "dc1sw", NULL,
+		    AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_DC1SW_MASK),
 	/* LDO regulator internally chained to DCDC5 */
 	AXP_DESC(AXP22X, DC5LDO, "dc5ldo", NULL, 700, 1400, 100,
-		 AXP22X_DC5LDO_V_OUT, 0x7, AXP22X_PWR_OUT_CTRL1, BIT(0)),
+		 AXP22X_DC5LDO_V_OUT, AXP22X_DC5LDO_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL1, AXP22X_PWR_OUT_DC5LDO_MASK),
 	AXP_DESC(AXP22X, ALDO1, "aldo1", "aldoin", 700, 3300, 100,
-		 AXP22X_ALDO1_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL1, BIT(6)),
+		 AXP22X_ALDO1_V_OUT, AXP22X_ALDO1_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL1, AXP22X_PWR_OUT_ALDO1_MASK),
 	AXP_DESC(AXP22X, ALDO2, "aldo2", "aldoin", 700, 3300, 100,
-		 AXP22X_ALDO2_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL1, BIT(7)),
+		 AXP22X_ALDO2_V_OUT, AXP22X_ALDO2_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL1, AXP22X_PWR_OUT_ALDO2_MASK),
 	AXP_DESC(AXP22X, ALDO3, "aldo3", "aldoin", 700, 3300, 100,
-		 AXP22X_ALDO3_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL3, BIT(7)),
+		 AXP22X_ALDO3_V_OUT, AXP22X_ALDO3_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL3, AXP22X_PWR_OUT_ALDO3_MASK),
 	AXP_DESC(AXP22X, DLDO1, "dldo1", "dldoin", 700, 3300, 100,
-		 AXP22X_DLDO1_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(3)),
+		 AXP22X_DLDO1_V_OUT, AXP22X_DLDO1_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_DLDO1_MASK),
 	AXP_DESC(AXP22X, DLDO2, "dldo2", "dldoin", 700, 3300, 100,
-		 AXP22X_DLDO2_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(4)),
+		 AXP22X_DLDO2_V_OUT, AXP22X_PWR_OUT_DLDO2_MASK,
+		 AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_DLDO2_MASK),
 	AXP_DESC(AXP22X, DLDO3, "dldo3", "dldoin", 700, 3300, 100,
-		 AXP22X_DLDO3_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(5)),
+		 AXP22X_DLDO3_V_OUT, AXP22X_DLDO3_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_DLDO3_MASK),
 	AXP_DESC(AXP22X, DLDO4, "dldo4", "dldoin", 700, 3300, 100,
-		 AXP22X_DLDO4_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(6)),
+		 AXP22X_DLDO4_V_OUT, AXP22X_DLDO4_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_DLDO4_MASK),
 	AXP_DESC(AXP22X, ELDO1, "eldo1", "eldoin", 700, 3300, 100,
-		 AXP22X_ELDO1_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(0)),
+		 AXP22X_ELDO1_V_OUT, AXP22X_ELDO1_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_ELDO1_MASK),
 	AXP_DESC(AXP22X, ELDO2, "eldo2", "eldoin", 700, 3300, 100,
-		 AXP22X_ELDO2_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(1)),
+		 AXP22X_ELDO2_V_OUT, AXP22X_ELDO2_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_ELDO1_MASK),
 	AXP_DESC(AXP22X, ELDO3, "eldo3", "eldoin", 700, 3300, 100,
-		 AXP22X_ELDO3_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(2)),
+		 AXP22X_ELDO3_V_OUT, AXP22X_ELDO3_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_ELDO3_MASK),
 	/* Note the datasheet only guarantees reliable operation up to
 	 * 3.3V, this needs to be enforced via dts provided constraints */
 	AXP_DESC_IO(AXP22X, LDO_IO0, "ldo_io0", "ips", 700, 3800, 100,
-		    AXP22X_LDO_IO0_V_OUT, 0x1f, AXP20X_GPIO0_CTRL, 0x07,
+		    AXP22X_LDO_IO0_V_OUT, AXP22X_LDO_IO0_V_OUT_MASK,
+		    AXP20X_GPIO0_CTRL, AXP20X_GPIO0_FUNC_MASK,
 		    AXP22X_IO_ENABLED, AXP22X_IO_DISABLED),
 	/* Note the datasheet only guarantees reliable operation up to
 	 * 3.3V, this needs to be enforced via dts provided constraints */
 	AXP_DESC_IO(AXP22X, LDO_IO1, "ldo_io1", "ips", 700, 3800, 100,
-		    AXP22X_LDO_IO1_V_OUT, 0x1f, AXP20X_GPIO1_CTRL, 0x07,
+		    AXP22X_LDO_IO1_V_OUT, AXP22X_LDO_IO1_V_OUT_MASK,
+		    AXP20X_GPIO1_CTRL, AXP20X_GPIO1_FUNC_MASK,
 		    AXP22X_IO_ENABLED, AXP22X_IO_DISABLED),
 	AXP_DESC_FIXED(AXP22X, RTC_LDO, "rtc_ldo", "ips", 3000),
 };
@@ -240,240 +638,354 @@ static const struct regulator_desc axp22x_drivevbus_regulator = {
 	.type		= REGULATOR_VOLTAGE,
 	.owner		= THIS_MODULE,
 	.enable_reg	= AXP20X_VBUS_IPSOUT_MGMT,
-	.enable_mask	= BIT(2),
+	.enable_mask	= AXP20X_VBUS_IPSOUT_MGMT_MASK,
 	.ops		= &axp20x_ops_sw,
 };
 
 /* DCDC ranges shared with AXP813 */
 static const struct regulator_linear_range axp803_dcdc234_ranges[] = {
-	REGULATOR_LINEAR_RANGE(500000, 0x0, 0x46, 10000),
-	REGULATOR_LINEAR_RANGE(1220000, 0x47, 0x4b, 20000),
+	REGULATOR_LINEAR_RANGE(500000,
+			       AXP803_DCDC234_500mV_START,
+			       AXP803_DCDC234_500mV_END,
+			       10000),
+	REGULATOR_LINEAR_RANGE(1220000,
+			       AXP803_DCDC234_1220mV_START,
+			       AXP803_DCDC234_1220mV_END,
+			       20000),
 };
 
 static const struct regulator_linear_range axp803_dcdc5_ranges[] = {
-	REGULATOR_LINEAR_RANGE(800000, 0x0, 0x20, 10000),
-	REGULATOR_LINEAR_RANGE(1140000, 0x21, 0x44, 20000),
+	REGULATOR_LINEAR_RANGE(800000,
+			       AXP803_DCDC5_800mV_START,
+			       AXP803_DCDC5_800mV_END,
+			       10000),
+	REGULATOR_LINEAR_RANGE(1140000,
+			       AXP803_DCDC5_1140mV_START,
+			       AXP803_DCDC5_1140mV_END,
+			       20000),
 };
 
 static const struct regulator_linear_range axp803_dcdc6_ranges[] = {
-	REGULATOR_LINEAR_RANGE(600000, 0x0, 0x32, 10000),
-	REGULATOR_LINEAR_RANGE(1120000, 0x33, 0x47, 20000),
+	REGULATOR_LINEAR_RANGE(600000,
+			       AXP803_DCDC6_600mV_START,
+			       AXP803_DCDC6_600mV_END,
+			       10000),
+	REGULATOR_LINEAR_RANGE(1120000,
+			       AXP803_DCDC6_1120mV_START,
+			       AXP803_DCDC6_1120mV_END,
+			       20000),
 };
 
-/* AXP806's CLDO2 and AXP809's DLDO1 shares the same range */
+/* AXP806's CLDO2 and AXP809's DLDO1 share the same range */
 static const struct regulator_linear_range axp803_dldo2_ranges[] = {
-	REGULATOR_LINEAR_RANGE(700000, 0x0, 0x1a, 100000),
-	REGULATOR_LINEAR_RANGE(3400000, 0x1b, 0x1f, 200000),
+	REGULATOR_LINEAR_RANGE(700000,
+			       AXP803_DLDO2_700mV_START,
+			       AXP803_DLDO2_700mV_END,
+			       100000),
+	REGULATOR_LINEAR_RANGE(3400000,
+			       AXP803_DLDO2_3400mV_START,
+			       AXP803_DLDO2_3400mV_END,
+			       200000),
 };
 
 static const struct regulator_desc axp803_regulators[] = {
 	AXP_DESC(AXP803, DCDC1, "dcdc1", "vin1", 1600, 3400, 100,
-		 AXP803_DCDC1_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL1, BIT(0)),
-	AXP_DESC_RANGES(AXP803, DCDC2, "dcdc2", "vin2", axp803_dcdc234_ranges,
-			76, AXP803_DCDC2_V_OUT, 0x7f, AXP22X_PWR_OUT_CTRL1,
-			BIT(1)),
-	AXP_DESC_RANGES(AXP803, DCDC3, "dcdc3", "vin3", axp803_dcdc234_ranges,
-			76, AXP803_DCDC3_V_OUT, 0x7f, AXP22X_PWR_OUT_CTRL1,
-			BIT(2)),
-	AXP_DESC_RANGES(AXP803, DCDC4, "dcdc4", "vin4", axp803_dcdc234_ranges,
-			76, AXP803_DCDC4_V_OUT, 0x7f, AXP22X_PWR_OUT_CTRL1,
-			BIT(3)),
-	AXP_DESC_RANGES(AXP803, DCDC5, "dcdc5", "vin5", axp803_dcdc5_ranges,
-			68, AXP803_DCDC5_V_OUT, 0x7f, AXP22X_PWR_OUT_CTRL1,
-			BIT(4)),
-	AXP_DESC_RANGES(AXP803, DCDC6, "dcdc6", "vin6", axp803_dcdc6_ranges,
-			72, AXP803_DCDC6_V_OUT, 0x7f, AXP22X_PWR_OUT_CTRL1,
-			BIT(5)),
+		 AXP803_DCDC1_V_OUT, AXP803_DCDC1_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL1, AXP803_PWR_OUT_DCDC1_MASK),
+	AXP_DESC_RANGES(AXP803, DCDC2, "dcdc2", "vin2",
+			axp803_dcdc234_ranges, AXP803_DCDC234_NUM_VOLTAGES,
+			AXP803_DCDC2_V_OUT, AXP803_DCDC2_V_OUT_MASK,
+			AXP22X_PWR_OUT_CTRL1, AXP803_PWR_OUT_DCDC2_MASK),
+	AXP_DESC_RANGES(AXP803, DCDC3, "dcdc3", "vin3",
+			axp803_dcdc234_ranges, AXP803_DCDC234_NUM_VOLTAGES,
+			AXP803_DCDC3_V_OUT, AXP803_DCDC3_V_OUT_MASK,
+			AXP22X_PWR_OUT_CTRL1, AXP803_PWR_OUT_DCDC3_MASK),
+	AXP_DESC_RANGES(AXP803, DCDC4, "dcdc4", "vin4",
+			axp803_dcdc234_ranges, AXP803_DCDC234_NUM_VOLTAGES,
+			AXP803_DCDC4_V_OUT, AXP803_DCDC4_V_OUT_MASK,
+			AXP22X_PWR_OUT_CTRL1, AXP803_PWR_OUT_DCDC4_MASK),
+	AXP_DESC_RANGES(AXP803, DCDC5, "dcdc5", "vin5",
+			axp803_dcdc5_ranges, AXP803_DCDC5_NUM_VOLTAGES,
+			AXP803_DCDC5_V_OUT, AXP803_DCDC5_V_OUT_MASK,
+			AXP22X_PWR_OUT_CTRL1, AXP803_PWR_OUT_DCDC5_MASK),
+	AXP_DESC_RANGES(AXP803, DCDC6, "dcdc6", "vin6",
+			axp803_dcdc6_ranges, AXP803_DCDC6_NUM_VOLTAGES,
+			AXP803_DCDC6_V_OUT, AXP803_DCDC6_V_OUT_MASK,
+			AXP22X_PWR_OUT_CTRL1, AXP803_PWR_OUT_DCDC6_MASK),
 	/* secondary switchable output of DCDC1 */
-	AXP_DESC_SW(AXP803, DC1SW, "dc1sw", NULL, AXP22X_PWR_OUT_CTRL2,
-		    BIT(7)),
+	AXP_DESC_SW(AXP803, DC1SW, "dc1sw", NULL,
+		    AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_DC1SW_MASK),
 	AXP_DESC(AXP803, ALDO1, "aldo1", "aldoin", 700, 3300, 100,
-		 AXP22X_ALDO1_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL3, BIT(5)),
+		 AXP22X_ALDO1_V_OUT, AXP22X_ALDO1_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL3, AXP806_PWR_OUT_ALDO1_MASK),
 	AXP_DESC(AXP803, ALDO2, "aldo2", "aldoin", 700, 3300, 100,
-		 AXP22X_ALDO2_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL3, BIT(6)),
+		 AXP22X_ALDO2_V_OUT, AXP22X_ALDO2_V_OUT,
+		 AXP22X_PWR_OUT_CTRL3, AXP806_PWR_OUT_ALDO2_MASK),
 	AXP_DESC(AXP803, ALDO3, "aldo3", "aldoin", 700, 3300, 100,
-		 AXP22X_ALDO3_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL3, BIT(7)),
+		 AXP22X_ALDO3_V_OUT, AXP22X_ALDO3_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL3, AXP806_PWR_OUT_ALDO3_MASK),
 	AXP_DESC(AXP803, DLDO1, "dldo1", "dldoin", 700, 3300, 100,
-		 AXP22X_DLDO1_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(3)),
-	AXP_DESC_RANGES(AXP803, DLDO2, "dldo2", "dldoin", axp803_dldo2_ranges,
-			32, AXP22X_DLDO2_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2,
-			BIT(4)),
+		 AXP22X_DLDO1_V_OUT, AXP22X_DLDO1_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_DLDO1_MASK),
+	AXP_DESC_RANGES(AXP803, DLDO2, "dldo2", "dldoin",
+			axp803_dldo2_ranges, AXP803_DLDO2_NUM_VOLTAGES,
+			AXP22X_DLDO2_V_OUT, AXP22X_DLDO2_V_OUT,
+			AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_DLDO2_MASK),
 	AXP_DESC(AXP803, DLDO3, "dldo3", "dldoin", 700, 3300, 100,
-		 AXP22X_DLDO3_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(5)),
+		 AXP22X_DLDO3_V_OUT, AXP22X_DLDO3_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_DLDO3_MASK),
 	AXP_DESC(AXP803, DLDO4, "dldo4", "dldoin", 700, 3300, 100,
-		 AXP22X_DLDO4_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(6)),
+		 AXP22X_DLDO4_V_OUT, AXP22X_DLDO4_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_DLDO4_MASK),
 	AXP_DESC(AXP803, ELDO1, "eldo1", "eldoin", 700, 1900, 50,
-		 AXP22X_ELDO1_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(0)),
+		 AXP22X_ELDO1_V_OUT, AXP22X_ELDO1_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_ELDO1_MASK),
 	AXP_DESC(AXP803, ELDO2, "eldo2", "eldoin", 700, 1900, 50,
-		 AXP22X_ELDO2_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(1)),
+		 AXP22X_ELDO2_V_OUT, AXP22X_ELDO2_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_ELDO2_MASK),
 	AXP_DESC(AXP803, ELDO3, "eldo3", "eldoin", 700, 1900, 50,
-		 AXP22X_ELDO3_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(2)),
+		 AXP22X_ELDO3_V_OUT, AXP22X_ELDO3_V_OUT,
+		 AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_ELDO3_MASK),
 	AXP_DESC(AXP803, FLDO1, "fldo1", "fldoin", 700, 1450, 50,
-		 AXP803_FLDO1_V_OUT, 0x0f, AXP22X_PWR_OUT_CTRL3, BIT(2)),
+		 AXP803_FLDO1_V_OUT, AXP803_FLDO1_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL3, AXP803_PWR_OUT_FLDO1_MASK),
 	AXP_DESC(AXP803, FLDO2, "fldo2", "fldoin", 700, 1450, 50,
-		 AXP803_FLDO2_V_OUT, 0x0f, AXP22X_PWR_OUT_CTRL3, BIT(3)),
+		 AXP803_FLDO2_V_OUT, AXP803_FLDO2_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL3, AXP803_PWR_OUT_FLDO2_MASK),
 	AXP_DESC_IO(AXP803, LDO_IO0, "ldo-io0", "ips", 700, 3300, 100,
-		    AXP22X_LDO_IO0_V_OUT, 0x1f, AXP20X_GPIO0_CTRL, 0x07,
+		    AXP22X_LDO_IO0_V_OUT, AXP22X_LDO_IO0_V_OUT_MASK,
+		    AXP20X_GPIO0_CTRL, AXP20X_GPIO0_FUNC_MASK,
 		    AXP22X_IO_ENABLED, AXP22X_IO_DISABLED),
 	AXP_DESC_IO(AXP803, LDO_IO1, "ldo-io1", "ips", 700, 3300, 100,
-		    AXP22X_LDO_IO1_V_OUT, 0x1f, AXP20X_GPIO1_CTRL, 0x07,
+		    AXP22X_LDO_IO1_V_OUT, AXP22X_LDO_IO1_V_OUT_MASK,
+		    AXP20X_GPIO1_CTRL, AXP20X_GPIO1_FUNC_MASK,
 		    AXP22X_IO_ENABLED, AXP22X_IO_DISABLED),
 	AXP_DESC_FIXED(AXP803, RTC_LDO, "rtc-ldo", "ips", 3000),
 };
 
 static const struct regulator_linear_range axp806_dcdca_ranges[] = {
-	REGULATOR_LINEAR_RANGE(600000, 0x0, 0x32, 10000),
-	REGULATOR_LINEAR_RANGE(1120000, 0x33, 0x47, 20000),
+	REGULATOR_LINEAR_RANGE(600000,
+			       AXP806_DCDCA_600mV_START,
+			       AXP806_DCDCA_600mV_END,
+			       10000),
+	REGULATOR_LINEAR_RANGE(1120000,
+			       AXP806_DCDCA_1120mV_START,
+			       AXP806_DCDCA_1120mV_END,
+			       20000),
 };
 
 static const struct regulator_linear_range axp806_dcdcd_ranges[] = {
-	REGULATOR_LINEAR_RANGE(600000, 0x0, 0x2d, 20000),
-	REGULATOR_LINEAR_RANGE(1600000, 0x2e, 0x3f, 100000),
+	REGULATOR_LINEAR_RANGE(600000,
+			       AXP806_DCDCD_600mV_START,
+			       AXP806_DCDCD_600mV_END,
+			       20000),
+	REGULATOR_LINEAR_RANGE(1600000,
+			       AXP806_DCDCD_600mV_START,
+			       AXP806_DCDCD_600mV_END,
+			       100000),
 };
 
 static const struct regulator_desc axp806_regulators[] = {
-	AXP_DESC_RANGES(AXP806, DCDCA, "dcdca", "vina", axp806_dcdca_ranges,
-			72, AXP806_DCDCA_V_CTRL, 0x7f, AXP806_PWR_OUT_CTRL1,
-			BIT(0)),
+	AXP_DESC_RANGES(AXP806, DCDCA, "dcdca", "vina",
+			axp806_dcdca_ranges, AXP806_DCDCA_NUM_VOLTAGES,
+			AXP806_DCDCA_V_CTRL, AXP806_DCDCA_V_CTRL_MASK,
+			AXP806_PWR_OUT_CTRL1, AXP806_PWR_OUT_DCDCA_MASK),
 	AXP_DESC(AXP806, DCDCB, "dcdcb", "vinb", 1000, 2550, 50,
-		 AXP806_DCDCB_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL1, BIT(1)),
-	AXP_DESC_RANGES(AXP806, DCDCC, "dcdcc", "vinc", axp806_dcdca_ranges,
-			72, AXP806_DCDCC_V_CTRL, 0x7f, AXP806_PWR_OUT_CTRL1,
-			BIT(2)),
-	AXP_DESC_RANGES(AXP806, DCDCD, "dcdcd", "vind", axp806_dcdcd_ranges,
-			64, AXP806_DCDCD_V_CTRL, 0x3f, AXP806_PWR_OUT_CTRL1,
-			BIT(3)),
+		 AXP806_DCDCB_V_CTRL, AXP806_DCDCB_V_CTRL,
+		 AXP806_PWR_OUT_CTRL1, AXP806_PWR_OUT_DCDCB_MASK),
+	AXP_DESC_RANGES(AXP806, DCDCC, "dcdcc", "vinc",
+			axp806_dcdca_ranges, AXP806_DCDCA_NUM_VOLTAGES,
+			AXP806_DCDCC_V_CTRL, AXP806_DCDCC_V_CTRL_MASK,
+			AXP806_PWR_OUT_CTRL1, AXP806_PWR_OUT_DCDCC_MASK),
+	AXP_DESC_RANGES(AXP806, DCDCD, "dcdcd", "vind",
+			axp806_dcdcd_ranges, AXP806_DCDCD_NUM_VOLTAGES,
+			AXP806_DCDCD_V_CTRL, AXP806_DCDCD_V_CTRL_MASK,
+			AXP806_PWR_OUT_CTRL1, AXP806_PWR_OUT_DCDCD_MASK),
 	AXP_DESC(AXP806, DCDCE, "dcdce", "vine", 1100, 3400, 100,
-		 AXP806_DCDCE_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL1, BIT(4)),
+		 AXP806_DCDCE_V_CTRL, AXP806_DCDCE_V_CTRL_MASK,
+		 AXP806_PWR_OUT_CTRL1, AXP806_PWR_OUT_DCDCE_MASK),
 	AXP_DESC(AXP806, ALDO1, "aldo1", "aldoin", 700, 3300, 100,
-		 AXP806_ALDO1_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL1, BIT(5)),
+		 AXP806_ALDO1_V_CTRL, AXP806_ALDO1_V_CTRL_MASK,
+		 AXP806_PWR_OUT_CTRL1, AXP806_PWR_OUT_ALDO1_MASK),
 	AXP_DESC(AXP806, ALDO2, "aldo2", "aldoin", 700, 3400, 100,
-		 AXP806_ALDO2_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL1, BIT(6)),
+		 AXP806_ALDO2_V_CTRL, AXP806_ALDO2_V_CTRL_MASK,
+		 AXP806_PWR_OUT_CTRL1, AXP806_PWR_OUT_ALDO2_MASK),
 	AXP_DESC(AXP806, ALDO3, "aldo3", "aldoin", 700, 3300, 100,
-		 AXP806_ALDO3_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL1, BIT(7)),
+		 AXP806_ALDO3_V_CTRL, AXP806_ALDO3_V_CTRL_MASK,
+		 AXP806_PWR_OUT_CTRL1, AXP806_PWR_OUT_ALDO3_MASK),
 	AXP_DESC(AXP806, BLDO1, "bldo1", "bldoin", 700, 1900, 100,
-		 AXP806_BLDO1_V_CTRL, 0x0f, AXP806_PWR_OUT_CTRL2, BIT(0)),
+		 AXP806_BLDO1_V_CTRL, AXP806_BLDO1_V_CTRL_MASK,
+		 AXP806_PWR_OUT_CTRL2, AXP806_PWR_OUT_BLDO1_MASK),
 	AXP_DESC(AXP806, BLDO2, "bldo2", "bldoin", 700, 1900, 100,
-		 AXP806_BLDO2_V_CTRL, 0x0f, AXP806_PWR_OUT_CTRL2, BIT(1)),
+		 AXP806_BLDO2_V_CTRL, AXP806_BLDO2_V_CTRL,
+		 AXP806_PWR_OUT_CTRL2, AXP806_PWR_OUT_BLDO2_MASK),
 	AXP_DESC(AXP806, BLDO3, "bldo3", "bldoin", 700, 1900, 100,
-		 AXP806_BLDO3_V_CTRL, 0x0f, AXP806_PWR_OUT_CTRL2, BIT(2)),
+		 AXP806_BLDO3_V_CTRL, AXP806_BLDO3_V_CTRL_MASK,
+		 AXP806_PWR_OUT_CTRL2, AXP806_PWR_OUT_BLDO3_MASK),
 	AXP_DESC(AXP806, BLDO4, "bldo4", "bldoin", 700, 1900, 100,
-		 AXP806_BLDO4_V_CTRL, 0x0f, AXP806_PWR_OUT_CTRL2, BIT(3)),
+		 AXP806_BLDO4_V_CTRL, AXP806_BLDO4_V_CTRL_MASK,
+		 AXP806_PWR_OUT_CTRL2, AXP806_PWR_OUT_BLDO4_MASK),
 	AXP_DESC(AXP806, CLDO1, "cldo1", "cldoin", 700, 3300, 100,
-		 AXP806_CLDO1_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL2, BIT(4)),
-	AXP_DESC_RANGES(AXP806, CLDO2, "cldo2", "cldoin", axp803_dldo2_ranges,
-			32, AXP806_CLDO2_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL2,
-			BIT(5)),
+		 AXP806_CLDO1_V_CTRL, AXP806_CLDO1_V_CTRL_MASK,
+		 AXP806_PWR_OUT_CTRL2, AXP806_PWR_OUT_CLDO1_MASK),
+	AXP_DESC_RANGES(AXP806, CLDO2, "cldo2", "cldoin",
+			axp803_dldo2_ranges, AXP803_DLDO2_NUM_VOLTAGES,
+			AXP806_CLDO2_V_CTRL, AXP806_CLDO2_V_CTRL_MASK,
+			AXP806_PWR_OUT_CTRL2, AXP806_PWR_OUT_CLDO2_MASK),
 	AXP_DESC(AXP806, CLDO3, "cldo3", "cldoin", 700, 3300, 100,
-		 AXP806_CLDO3_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL2, BIT(6)),
-	AXP_DESC_SW(AXP806, SW, "sw", "swin", AXP806_PWR_OUT_CTRL2, BIT(7)),
+		 AXP806_CLDO3_V_CTRL, AXP806_CLDO3_V_CTRL_MASK,
+		 AXP806_PWR_OUT_CTRL2, AXP806_PWR_OUT_CLDO3_MASK),
+	AXP_DESC_SW(AXP806, SW, "sw", "swin",
+		    AXP806_PWR_OUT_CTRL2, AXP806_PWR_OUT_SW_MASK),
 };
 
 static const struct regulator_linear_range axp809_dcdc4_ranges[] = {
-	REGULATOR_LINEAR_RANGE(600000, 0x0, 0x2f, 20000),
-	REGULATOR_LINEAR_RANGE(1800000, 0x30, 0x38, 100000),
+	REGULATOR_LINEAR_RANGE(600000,
+			       AXP809_DCDC4_600mV_START,
+			       AXP809_DCDC4_600mV_END,
+			       20000),
+	REGULATOR_LINEAR_RANGE(1800000,
+			       AXP809_DCDC4_1800mV_START,
+			       AXP809_DCDC4_1800mV_END,
+			       100000),
 };
 
 static const struct regulator_desc axp809_regulators[] = {
 	AXP_DESC(AXP809, DCDC1, "dcdc1", "vin1", 1600, 3400, 100,
-		 AXP22X_DCDC1_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL1, BIT(1)),
+		 AXP22X_DCDC1_V_OUT, AXP22X_DCDC1_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL1, AXP22X_PWR_OUT_DCDC1_MASK),
 	AXP_DESC(AXP809, DCDC2, "dcdc2", "vin2", 600, 1540, 20,
-		 AXP22X_DCDC2_V_OUT, 0x3f, AXP22X_PWR_OUT_CTRL1, BIT(2)),
+		 AXP22X_DCDC2_V_OUT, AXP22X_DCDC2_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL1, AXP22X_PWR_OUT_DCDC2_MASK),
 	AXP_DESC(AXP809, DCDC3, "dcdc3", "vin3", 600, 1860, 20,
-		 AXP22X_DCDC3_V_OUT, 0x3f, AXP22X_PWR_OUT_CTRL1, BIT(3)),
-	AXP_DESC_RANGES(AXP809, DCDC4, "dcdc4", "vin4", axp809_dcdc4_ranges,
-			57, AXP22X_DCDC4_V_OUT, 0x3f, AXP22X_PWR_OUT_CTRL1,
-			BIT(4)),
+		 AXP22X_DCDC3_V_OUT, AXP22X_DCDC3_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL1, AXP22X_PWR_OUT_DCDC3_MASK),
+	AXP_DESC_RANGES(AXP809, DCDC4, "dcdc4", "vin4",
+			axp809_dcdc4_ranges, AXP809_DCDC4_NUM_VOLTAGES,
+			AXP22X_DCDC4_V_OUT, AXP22X_DCDC4_V_OUT_MASK,
+			AXP22X_PWR_OUT_CTRL1, AXP22X_PWR_OUT_DCDC4_MASK),
 	AXP_DESC(AXP809, DCDC5, "dcdc5", "vin5", 1000, 2550, 50,
-		 AXP22X_DCDC5_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL1, BIT(5)),
+		 AXP22X_DCDC5_V_OUT, AXP22X_DCDC5_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL1, AXP22X_PWR_OUT_DCDC5_MASK),
 	/* secondary switchable output of DCDC1 */
-	AXP_DESC_SW(AXP809, DC1SW, "dc1sw", NULL, AXP22X_PWR_OUT_CTRL2,
-		    BIT(7)),
+	AXP_DESC_SW(AXP809, DC1SW, "dc1sw", NULL,
+		    AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_DC1SW_MASK),
 	/* LDO regulator internally chained to DCDC5 */
 	AXP_DESC(AXP809, DC5LDO, "dc5ldo", NULL, 700, 1400, 100,
-		 AXP22X_DC5LDO_V_OUT, 0x7, AXP22X_PWR_OUT_CTRL1, BIT(0)),
+		 AXP22X_DC5LDO_V_OUT, AXP22X_DC5LDO_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL1, AXP22X_PWR_OUT_DC5LDO_MASK),
 	AXP_DESC(AXP809, ALDO1, "aldo1", "aldoin", 700, 3300, 100,
-		 AXP22X_ALDO1_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL1, BIT(6)),
+		 AXP22X_ALDO1_V_OUT, AXP22X_ALDO1_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL1, AXP22X_PWR_OUT_ALDO1_MASK),
 	AXP_DESC(AXP809, ALDO2, "aldo2", "aldoin", 700, 3300, 100,
-		 AXP22X_ALDO2_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL1, BIT(7)),
+		 AXP22X_ALDO2_V_OUT, AXP22X_ALDO2_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL1, AXP22X_PWR_OUT_ALDO2_MASK),
 	AXP_DESC(AXP809, ALDO3, "aldo3", "aldoin", 700, 3300, 100,
-		 AXP22X_ALDO3_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(5)),
-	AXP_DESC_RANGES(AXP809, DLDO1, "dldo1", "dldoin", axp803_dldo2_ranges,
-			32, AXP22X_DLDO1_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2,
-			BIT(3)),
+		 AXP22X_ALDO3_V_OUT, AXP22X_ALDO3_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_ALDO3_MASK),
+	AXP_DESC_RANGES(AXP809, DLDO1, "dldo1", "dldoin",
+			axp803_dldo2_ranges, AXP803_DLDO2_NUM_VOLTAGES,
+			AXP22X_DLDO1_V_OUT, AXP22X_DLDO1_V_OUT_MASK,
+			AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_DLDO1_MASK),
 	AXP_DESC(AXP809, DLDO2, "dldo2", "dldoin", 700, 3300, 100,
-		 AXP22X_DLDO2_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(4)),
+		 AXP22X_DLDO2_V_OUT, AXP22X_DLDO2_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_DLDO2_MASK),
 	AXP_DESC(AXP809, ELDO1, "eldo1", "eldoin", 700, 3300, 100,
-		 AXP22X_ELDO1_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(0)),
+		 AXP22X_ELDO1_V_OUT, AXP22X_ELDO1_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_ELDO1_MASK),
 	AXP_DESC(AXP809, ELDO2, "eldo2", "eldoin", 700, 3300, 100,
-		 AXP22X_ELDO2_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(1)),
+		 AXP22X_ELDO2_V_OUT, AXP22X_ELDO2_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_ELDO2_MASK),
 	AXP_DESC(AXP809, ELDO3, "eldo3", "eldoin", 700, 3300, 100,
-		 AXP22X_ELDO3_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(2)),
+		 AXP22X_ELDO3_V_OUT, AXP22X_ELDO3_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_ELDO3_MASK),
 	/*
 	 * Note the datasheet only guarantees reliable operation up to
 	 * 3.3V, this needs to be enforced via dts provided constraints
 	 */
 	AXP_DESC_IO(AXP809, LDO_IO0, "ldo_io0", "ips", 700, 3800, 100,
-		    AXP22X_LDO_IO0_V_OUT, 0x1f, AXP20X_GPIO0_CTRL, 0x07,
+		    AXP22X_LDO_IO0_V_OUT, AXP22X_LDO_IO0_V_OUT_MASK,
+		    AXP20X_GPIO0_CTRL, AXP20X_GPIO0_FUNC_MASK,
 		    AXP22X_IO_ENABLED, AXP22X_IO_DISABLED),
 	/*
 	 * Note the datasheet only guarantees reliable operation up to
 	 * 3.3V, this needs to be enforced via dts provided constraints
 	 */
 	AXP_DESC_IO(AXP809, LDO_IO1, "ldo_io1", "ips", 700, 3800, 100,
-		    AXP22X_LDO_IO1_V_OUT, 0x1f, AXP20X_GPIO1_CTRL, 0x07,
+		    AXP22X_LDO_IO1_V_OUT, AXP22X_LDO_IO1_V_OUT_MASK,
+		    AXP20X_GPIO1_CTRL, AXP20X_GPIO1_FUNC_MASK,
 		    AXP22X_IO_ENABLED, AXP22X_IO_DISABLED),
 	AXP_DESC_FIXED(AXP809, RTC_LDO, "rtc_ldo", "ips", 1800),
-	AXP_DESC_SW(AXP809, SW, "sw", "swin", AXP22X_PWR_OUT_CTRL2, BIT(6)),
+	AXP_DESC_SW(AXP809, SW, "sw", "swin",
+		    AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_SW_MASK),
 };
 
 static const struct regulator_desc axp813_regulators[] = {
 	AXP_DESC(AXP813, DCDC1, "dcdc1", "vin1", 1600, 3400, 100,
-		 AXP803_DCDC1_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL1, BIT(0)),
-	AXP_DESC_RANGES(AXP813, DCDC2, "dcdc2", "vin2", axp803_dcdc234_ranges,
-			76, AXP803_DCDC2_V_OUT, 0x7f, AXP22X_PWR_OUT_CTRL1,
-			BIT(1)),
-	AXP_DESC_RANGES(AXP813, DCDC3, "dcdc3", "vin3", axp803_dcdc234_ranges,
-			76, AXP803_DCDC3_V_OUT, 0x7f, AXP22X_PWR_OUT_CTRL1,
-			BIT(2)),
-	AXP_DESC_RANGES(AXP813, DCDC4, "dcdc4", "vin4", axp803_dcdc234_ranges,
-			76, AXP803_DCDC4_V_OUT, 0x7f, AXP22X_PWR_OUT_CTRL1,
-			BIT(3)),
-	AXP_DESC_RANGES(AXP813, DCDC5, "dcdc5", "vin5", axp803_dcdc5_ranges,
-			68, AXP803_DCDC5_V_OUT, 0x7f, AXP22X_PWR_OUT_CTRL1,
-			BIT(4)),
-	AXP_DESC_RANGES(AXP813, DCDC6, "dcdc6", "vin6", axp803_dcdc6_ranges,
-			72, AXP803_DCDC6_V_OUT, 0x7f, AXP22X_PWR_OUT_CTRL1,
-			BIT(5)),
-	AXP_DESC_RANGES(AXP813, DCDC7, "dcdc7", "vin7", axp803_dcdc6_ranges,
-			72, AXP813_DCDC7_V_OUT, 0x7f, AXP22X_PWR_OUT_CTRL1,
-			BIT(6)),
+		 AXP803_DCDC1_V_OUT, AXP803_DCDC1_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL1, AXP803_PWR_OUT_DCDC1_MASK),
+	AXP_DESC_RANGES(AXP813, DCDC2, "dcdc2", "vin2",
+			axp803_dcdc234_ranges, AXP803_DCDC234_NUM_VOLTAGES,
+			AXP803_DCDC2_V_OUT, AXP803_DCDC2_V_OUT_MASK,
+			AXP22X_PWR_OUT_CTRL1, AXP803_PWR_OUT_DCDC2_MASK),
+	AXP_DESC_RANGES(AXP813, DCDC3, "dcdc3", "vin3",
+			axp803_dcdc234_ranges, AXP803_DCDC234_NUM_VOLTAGES,
+			AXP803_DCDC3_V_OUT, AXP803_DCDC3_V_OUT_MASK,
+			AXP22X_PWR_OUT_CTRL1, AXP803_PWR_OUT_DCDC3_MASK),
+	AXP_DESC_RANGES(AXP813, DCDC4, "dcdc4", "vin4",
+			axp803_dcdc234_ranges, AXP803_DCDC234_NUM_VOLTAGES,
+			AXP803_DCDC4_V_OUT, AXP803_DCDC4_V_OUT_MASK,
+			AXP22X_PWR_OUT_CTRL1, AXP803_PWR_OUT_DCDC4_MASK),
+	AXP_DESC_RANGES(AXP813, DCDC5, "dcdc5", "vin5",
+			axp803_dcdc5_ranges, AXP803_DCDC5_NUM_VOLTAGES,
+			AXP803_DCDC5_V_OUT, AXP803_DCDC5_V_OUT_MASK,
+			AXP22X_PWR_OUT_CTRL1, AXP803_PWR_OUT_DCDC5_MASK),
+	AXP_DESC_RANGES(AXP813, DCDC6, "dcdc6", "vin6",
+			axp803_dcdc6_ranges, AXP803_DCDC6_NUM_VOLTAGES,
+			AXP803_DCDC6_V_OUT, AXP803_DCDC6_V_OUT_MASK,
+			AXP22X_PWR_OUT_CTRL1, AXP803_PWR_OUT_DCDC6_MASK),
+	AXP_DESC_RANGES(AXP813, DCDC7, "dcdc7", "vin7",
+			axp803_dcdc6_ranges, AXP803_DCDC6_NUM_VOLTAGES,
+			AXP813_DCDC7_V_OUT, AXP813_DCDC7_V_OUT_MASK,
+			AXP22X_PWR_OUT_CTRL1, AXP813_PWR_OUT_DCDC7_MASK),
 	AXP_DESC(AXP813, ALDO1, "aldo1", "aldoin", 700, 3300, 100,
-		 AXP22X_ALDO1_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL3, BIT(5)),
+		 AXP22X_ALDO1_V_OUT, AXP22X_ALDO1_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL3, AXP806_PWR_OUT_ALDO1_MASK),
 	AXP_DESC(AXP813, ALDO2, "aldo2", "aldoin", 700, 3300, 100,
-		 AXP22X_ALDO2_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL3, BIT(6)),
+		 AXP22X_ALDO2_V_OUT, AXP22X_ALDO2_V_OUT,
+		 AXP22X_PWR_OUT_CTRL3, AXP806_PWR_OUT_ALDO2_MASK),
 	AXP_DESC(AXP813, ALDO3, "aldo3", "aldoin", 700, 3300, 100,
-		 AXP22X_ALDO3_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL3, BIT(7)),
+		 AXP22X_ALDO3_V_OUT, AXP22X_ALDO3_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL3, AXP806_PWR_OUT_ALDO3_MASK),
 	AXP_DESC(AXP813, DLDO1, "dldo1", "dldoin", 700, 3300, 100,
-		 AXP22X_DLDO1_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(3)),
-	AXP_DESC_RANGES(AXP813, DLDO2, "dldo2", "dldoin", axp803_dldo2_ranges,
-			32, AXP22X_DLDO2_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2,
-			BIT(4)),
+		 AXP22X_DLDO1_V_OUT, AXP22X_DLDO1_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_DLDO1_MASK),
+	AXP_DESC_RANGES(AXP813, DLDO2, "dldo2", "dldoin",
+			axp803_dldo2_ranges, AXP803_DLDO2_NUM_VOLTAGES,
+			AXP22X_DLDO2_V_OUT, AXP22X_DLDO2_V_OUT,
+			AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_DLDO2_MASK),
 	AXP_DESC(AXP813, DLDO3, "dldo3", "dldoin", 700, 3300, 100,
-		 AXP22X_DLDO3_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(5)),
+		 AXP22X_DLDO3_V_OUT, AXP22X_DLDO3_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_DLDO3_MASK),
 	AXP_DESC(AXP813, DLDO4, "dldo4", "dldoin", 700, 3300, 100,
-		 AXP22X_DLDO4_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(6)),
+		 AXP22X_DLDO4_V_OUT, AXP22X_DLDO4_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_DLDO4_MASK),
 	AXP_DESC(AXP813, ELDO1, "eldo1", "eldoin", 700, 1900, 50,
-		 AXP22X_ELDO1_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(0)),
+		 AXP22X_ELDO1_V_OUT, AXP22X_ELDO1_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_ELDO1_MASK),
 	AXP_DESC(AXP813, ELDO2, "eldo2", "eldoin", 700, 1900, 50,
-		 AXP22X_ELDO2_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(1)),
+		 AXP22X_ELDO2_V_OUT, AXP22X_ELDO2_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_ELDO2_MASK),
 	AXP_DESC(AXP813, ELDO3, "eldo3", "eldoin", 700, 1900, 50,
-		 AXP22X_ELDO3_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(2)),
+		 AXP22X_ELDO3_V_OUT, AXP22X_ELDO3_V_OUT,
+		 AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_ELDO3_MASK),
 	/* to do / check ... */
 	AXP_DESC(AXP813, FLDO1, "fldo1", "fldoin", 700, 1450, 50,
-		 AXP803_FLDO1_V_OUT, 0x0f, AXP22X_PWR_OUT_CTRL3, BIT(2)),
+		 AXP803_FLDO1_V_OUT, AXP803_FLDO1_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL3, AXP803_PWR_OUT_FLDO1_MASK),
 	AXP_DESC(AXP813, FLDO2, "fldo2", "fldoin", 700, 1450, 50,
-		 AXP803_FLDO2_V_OUT, 0x0f, AXP22X_PWR_OUT_CTRL3, BIT(3)),
+		 AXP803_FLDO2_V_OUT, AXP803_FLDO2_V_OUT_MASK,
+		 AXP22X_PWR_OUT_CTRL3, AXP803_PWR_OUT_FLDO2_MASK),
 	/*
 	 * TODO: FLDO3 = {DCDC5, FLDOIN} / 2
 	 *
@@ -482,12 +994,15 @@ static const struct regulator_desc axp813_regulators[] = {
 	 */
 	AXP_DESC_FIXED(AXP813, RTC_LDO, "rtc-ldo", "ips", 1800),
 	AXP_DESC_IO(AXP813, LDO_IO0, "ldo-io0", "ips", 700, 3300, 100,
-		    AXP22X_LDO_IO0_V_OUT, 0x1f, AXP20X_GPIO0_CTRL, 0x07,
+		    AXP22X_LDO_IO0_V_OUT, AXP22X_LDO_IO0_V_OUT_MASK,
+		    AXP20X_GPIO0_CTRL, AXP20X_GPIO0_FUNC_MASK,
 		    AXP22X_IO_ENABLED, AXP22X_IO_DISABLED),
 	AXP_DESC_IO(AXP813, LDO_IO1, "ldo-io1", "ips", 700, 3300, 100,
-		    AXP22X_LDO_IO1_V_OUT, 0x1f, AXP20X_GPIO1_CTRL, 0x07,
+		    AXP22X_LDO_IO1_V_OUT, AXP22X_LDO_IO1_V_OUT_MASK,
+		    AXP20X_GPIO1_CTRL, AXP20X_GPIO1_FUNC_MASK,
 		    AXP22X_IO_ENABLED, AXP22X_IO_DISABLED),
-	AXP_DESC_SW(AXP813, SW, "sw", "swin", AXP22X_PWR_OUT_CTRL2, BIT(7)),
+	AXP_DESC_SW(AXP813, SW, "sw", "swin",
+		    AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_DC1SW_MASK),
 };
 
 static int axp20x_set_dcdc_freq(struct platform_device *pdev, u32 dcdcfreq)
@@ -663,9 +1178,9 @@ static bool axp20x_is_polyphase_slave(struct axp20x_dev *axp20x, int id)
 
 		switch (id) {
 		case AXP803_DCDC3:
-			return !!(reg & BIT(6));
+			return !!(reg & AXP803_DCDC23_POLYPHASE_DUAL);
 		case AXP803_DCDC6:
-			return !!(reg & BIT(5));
+			return !!(reg & AXP803_DCDC56_POLYPHASE_DUAL);
 		}
 		break;
 
@@ -674,12 +1189,15 @@ static bool axp20x_is_polyphase_slave(struct axp20x_dev *axp20x, int id)
 
 		switch (id) {
 		case AXP806_DCDCB:
-			return (((reg & GENMASK(7, 6)) == BIT(6)) ||
-				((reg & GENMASK(7, 6)) == BIT(7)));
+			return (((reg & AXP806_DCDCABC_POLYPHASE_MASK) ==
+				AXP806_DCDCAB_POLYPHASE_DUAL) ||
+				((reg & AXP806_DCDCABC_POLYPHASE_MASK) ==
+				AXP806_DCDCABC_POLYPHASE_TRI));
 		case AXP806_DCDCC:
-			return ((reg & GENMASK(7, 6)) == BIT(7));
+			return ((reg & AXP806_DCDCABC_POLYPHASE_MASK) ==
+				AXP806_DCDCABC_POLYPHASE_TRI);
 		case AXP806_DCDCE:
-			return !!(reg & BIT(5));
+			return !!(reg & AXP806_DCDCDE_POLYPHASE_DUAL);
 		}
 		break;
 

drivers/regulator/bd718x7-regulator.c

@@ -9,6 +9,7 @@
 #include <linux/kernel.h>
 #include <linux/mfd/rohm-bd718x7.h>
 #include <linux/module.h>
+#include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/regulator/driver.h>
 #include <linux/regulator/machine.h>
@@ -130,6 +131,7 @@ static struct regulator_ops bd718xx_buck_regulator_nolinear_ops = {
 	.disable = regulator_disable_regmap,
 	.is_enabled = regulator_is_enabled_regmap,
 	.list_voltage = regulator_list_voltage_table,
+	.map_voltage = regulator_map_voltage_ascend,
 	.set_voltage_sel = bd718xx_set_voltage_sel_restricted,
 	.get_voltage_sel = regulator_get_voltage_sel_regmap,
 	.set_voltage_time_sel = regulator_set_voltage_time_sel,
@@ -1007,7 +1009,7 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = {
 };
 
 struct bd718xx_pmic_inits {
-	const struct bd718xx_regulator_data (*r_datas)[];
+	const struct bd718xx_regulator_data *r_datas;
 	unsigned int r_amount;
 };
 
@@ -1017,11 +1019,11 @@ static int bd718xx_probe(struct platform_device *pdev)
 	struct regulator_config config = { 0 };
 	struct bd718xx_pmic_inits pmic_regulators[] = {
 		[BD718XX_TYPE_BD71837] = {
-			.r_datas = &bd71837_regulators,
+			.r_datas = bd71837_regulators,
 			.r_amount = ARRAY_SIZE(bd71837_regulators),
 		},
 		[BD718XX_TYPE_BD71847] = {
-			.r_datas = &bd71847_regulators,
+			.r_datas = bd71847_regulators,
 			.r_amount = ARRAY_SIZE(bd71847_regulators),
 		},
 	};
@@ -1053,13 +1055,36 @@ static int bd718xx_probe(struct platform_device *pdev)
 			BD718XX_REG_REGLOCK);
 	}
 
+	/* At poweroff transition PMIC HW disables EN bit for regulators but
+	 * leaves SEL bit untouched. So if state transition from POWEROFF
+	 * is done to SNVS - then all power rails controlled by SW (having
+	 * SEL bit set) stay disabled as EN is cleared. This may result boot
+	 * failure if any crucial systems are powered by these rails.
+	 *
+	 * Change the next stage from poweroff to be READY instead of SNVS
+	 * for all reset types because OTP loading at READY will clear SEL
+	 * bit allowing HW defaults for power rails to be used
+	 */
+	err = regmap_update_bits(mfd->regmap, BD718XX_REG_TRANS_COND1,
+				 BD718XX_ON_REQ_POWEROFF_MASK |
+				 BD718XX_SWRESET_POWEROFF_MASK |
+				 BD718XX_WDOG_POWEROFF_MASK |
+				 BD718XX_KEY_L_POWEROFF_MASK,
+				 BD718XX_POWOFF_TO_RDY);
+	if (err) {
+		dev_err(&pdev->dev, "Failed to change reset target\n");
+		goto err;
+	} else {
+		dev_dbg(&pdev->dev, "Changed all resets from SVNS to READY\n");
+	}
+
 	for (i = 0; i < pmic_regulators[mfd->chip_type].r_amount; i++) {
 
 		const struct regulator_desc *desc;
 		struct regulator_dev *rdev;
 		const struct bd718xx_regulator_data *r;
 
-		r = &(*pmic_regulators[mfd->chip_type].r_datas)[i];
+		r = &pmic_regulators[mfd->chip_type].r_datas[i];
 		desc = &r->desc;
 
 		config.dev = pdev->dev.parent;

drivers/regulator/bd9571mwv-regulator.c

+// SPDX-License-Identifier: GPL-2.0
 /*
  * ROHM BD9571MWV-M regulator driver
  *
  * Copyright (C) 2017 Marek Vasut <marek.vasut+renesas@gmail.com>
  *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether expressed or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License version 2 for more details.
- *
  * Based on the TPS65086 driver
  *
  * NOTE: VD09 is missing

drivers/regulator/core.c

@@ -50,6 +50,8 @@
 #define rdev_dbg(rdev, fmt, ...)					\
 	pr_debug("%s: " fmt, rdev_get_name(rdev), ##__VA_ARGS__)
 
+static DEFINE_WW_CLASS(regulator_ww_class);
+static DEFINE_MUTEX(regulator_nesting_mutex);
 static DEFINE_MUTEX(regulator_list_mutex);
 static LIST_HEAD(regulator_map_list);
 static LIST_HEAD(regulator_ena_gpio_list);
@@ -97,7 +99,7 @@ struct regulator_supply_alias {
 };
 
 static int _regulator_is_enabled(struct regulator_dev *rdev);
-static int _regulator_disable(struct regulator_dev *rdev);
+static int _regulator_disable(struct regulator *regulator);
 static int _regulator_get_voltage(struct regulator_dev *rdev);
 static int _regulator_get_current_limit(struct regulator_dev *rdev);
 static unsigned int _regulator_get_mode(struct regulator_dev *rdev);
@@ -105,6 +107,11 @@ static int _notifier_call_chain(struct regulator_dev *rdev,
 				  unsigned long event, void *data);
 static int _regulator_do_set_voltage(struct regulator_dev *rdev,
 				     int min_uV, int max_uV);
+static int regulator_balance_voltage(struct regulator_dev *rdev,
+				     suspend_state_t state);
+static int regulator_set_voltage_rdev(struct regulator_dev *rdev,
+				      int min_uV, int max_uV,
+				      suspend_state_t state);
 static struct regulator *create_regulator(struct regulator_dev *rdev,
 					  struct device *dev,
 					  const char *supply_name);
@@ -149,7 +156,7 @@ static inline struct regulator_dev *rdev_get_supply(struct regulator_dev *rdev)
 /**
  * regulator_lock_nested - lock a single regulator
  * @rdev:		regulator source
- * @subclass:		mutex subclass used for lockdep
+ * @ww_ctx:		w/w mutex acquire context
  *
  * This function can be called many times by one task on
  * a single regulator and its mutex will be locked only
@@ -157,25 +164,54 @@ static inline struct regulator_dev *rdev_get_supply(struct regulator_dev *rdev)
  * than the one, which initially locked the mutex, it will
  * wait on mutex.
  */
-static void regulator_lock_nested(struct regulator_dev *rdev,
-				  unsigned int subclass)
+static inline int regulator_lock_nested(struct regulator_dev *rdev,
+					struct ww_acquire_ctx *ww_ctx)
 {
-	if (!mutex_trylock(&rdev->mutex)) {
-		if (rdev->mutex_owner == current) {
+	bool lock = false;
+	int ret = 0;
+
+	mutex_lock(&regulator_nesting_mutex);
+
+	if (ww_ctx || !ww_mutex_trylock(&rdev->mutex)) {
+		if (rdev->mutex_owner == current)
 			rdev->ref_cnt++;
-			return;
+		else
+			lock = true;
+
+		if (lock) {
+			mutex_unlock(&regulator_nesting_mutex);
+			ret = ww_mutex_lock(&rdev->mutex, ww_ctx);
+			mutex_lock(&regulator_nesting_mutex);
 		}
-		mutex_lock_nested(&rdev->mutex, subclass);
+	} else {
+		lock = true;
+	}
+
+	if (lock && ret != -EDEADLK) {
+		rdev->ref_cnt++;
+		rdev->mutex_owner = current;
 	}
 
-	rdev->ref_cnt = 1;
-	rdev->mutex_owner = current;
+	mutex_unlock(&regulator_nesting_mutex);
+
+	return ret;
 }
 
-static inline void regulator_lock(struct regulator_dev *rdev)
+/**
+ * regulator_lock - lock a single regulator
+ * @rdev:		regulator source
+ *
+ * This function can be called many times by one task on
+ * a single regulator and its mutex will be locked only
+ * once. If a task, which is calling this function is other
+ * than the one, which initially locked the mutex, it will
+ * wait on mutex.
+ */
+void regulator_lock(struct regulator_dev *rdev)
 {
-	regulator_lock_nested(rdev, 0);
+	regulator_lock_nested(rdev, NULL);
 }
+EXPORT_SYMBOL_GPL(regulator_lock);
 
 /**
  * regulator_unlock - unlock a single regulator
@@ -184,47 +220,191 @@ static inline void regulator_lock(struct regulator_dev *rdev)
  * This function unlocks the mutex when the
  * reference counter reaches 0.
  */
-static void regulator_unlock(struct regulator_dev *rdev)
+void regulator_unlock(struct regulator_dev *rdev)
+{
+	mutex_lock(&regulator_nesting_mutex);
+
+	if (--rdev->ref_cnt == 0) {
+		rdev->mutex_owner = NULL;
+		ww_mutex_unlock(&rdev->mutex);
+	}
+
+	WARN_ON_ONCE(rdev->ref_cnt < 0);
+
+	mutex_unlock(&regulator_nesting_mutex);
+}
+EXPORT_SYMBOL_GPL(regulator_unlock);
+
+static bool regulator_supply_is_couple(struct regulator_dev *rdev)
+{
+	struct regulator_dev *c_rdev;
+	int i;
+
+	for (i = 1; i < rdev->coupling_desc.n_coupled; i++) {
+		c_rdev = rdev->coupling_desc.coupled_rdevs[i];
+
+		if (rdev->supply->rdev == c_rdev)
+			return true;
+	}
+
+	return false;
+}
+
+static void regulator_unlock_recursive(struct regulator_dev *rdev,
+				       unsigned int n_coupled)
+{
+	struct regulator_dev *c_rdev;
+	int i;
+
+	for (i = n_coupled; i > 0; i--) {
+		c_rdev = rdev->coupling_desc.coupled_rdevs[i - 1];
+
+		if (!c_rdev)
+			continue;
+
+		if (c_rdev->supply && !regulator_supply_is_couple(c_rdev))
+			regulator_unlock_recursive(
+					c_rdev->supply->rdev,
+					c_rdev->coupling_desc.n_coupled);
+
+		regulator_unlock(c_rdev);
+	}
+}
+
+static int regulator_lock_recursive(struct regulator_dev *rdev,
+				    struct regulator_dev **new_contended_rdev,
+				    struct regulator_dev **old_contended_rdev,
+				    struct ww_acquire_ctx *ww_ctx)
 {
-	if (rdev->ref_cnt != 0) {
-		rdev->ref_cnt--;
+	struct regulator_dev *c_rdev;
+	int i, err;
 
-		if (!rdev->ref_cnt) {
-			rdev->mutex_owner = NULL;
-			mutex_unlock(&rdev->mutex);
+	for (i = 0; i < rdev->coupling_desc.n_coupled; i++) {
+		c_rdev = rdev->coupling_desc.coupled_rdevs[i];
+
+		if (!c_rdev)
+			continue;
+
+		if (c_rdev != *old_contended_rdev) {
+			err = regulator_lock_nested(c_rdev, ww_ctx);
+			if (err) {
+				if (err == -EDEADLK) {
+					*new_contended_rdev = c_rdev;
+					goto err_unlock;
+				}
+
+				/* shouldn't happen */
+				WARN_ON_ONCE(err != -EALREADY);
+			}
+		} else {
+			*old_contended_rdev = NULL;
+		}
+
+		if (c_rdev->supply && !regulator_supply_is_couple(c_rdev)) {
+			err = regulator_lock_recursive(c_rdev->supply->rdev,
+						       new_contended_rdev,
+						       old_contended_rdev,
+						       ww_ctx);
+			if (err) {
+				regulator_unlock(c_rdev);
+				goto err_unlock;
+			}
 		}
 	}
+
+	return 0;
+
+err_unlock:
+	regulator_unlock_recursive(rdev, i);
+
+	return err;
 }
 
 /**
- * regulator_lock_supply - lock a regulator and its supplies
- * @rdev:         regulator source
+ * regulator_unlock_dependent - unlock regulator's suppliers and coupled
+ *				regulators
+ * @rdev:			regulator source
+ * @ww_ctx:			w/w mutex acquire context
+ *
+ * Unlock all regulators related with rdev by coupling or suppling.
  */
-static void regulator_lock_supply(struct regulator_dev *rdev)
+static void regulator_unlock_dependent(struct regulator_dev *rdev,
+				       struct ww_acquire_ctx *ww_ctx)
 {
-	int i;
-
-	for (i = 0; rdev; rdev = rdev_get_supply(rdev), i++)
-		regulator_lock_nested(rdev, i);
+	regulator_unlock_recursive(rdev, rdev->coupling_desc.n_coupled);
+	ww_acquire_fini(ww_ctx);
 }
 
 /**
- * regulator_unlock_supply - unlock a regulator and its supplies
- * @rdev:         regulator source
+ * regulator_lock_dependent - lock regulator's suppliers and coupled regulators
+ * @rdev:			regulator source
+ * @ww_ctx:			w/w mutex acquire context
+ *
+ * This function as a wrapper on regulator_lock_recursive(), which locks
+ * all regulators related with rdev by coupling or suppling.
  */
-static void regulator_unlock_supply(struct regulator_dev *rdev)
+static void regulator_lock_dependent(struct regulator_dev *rdev,
+				     struct ww_acquire_ctx *ww_ctx)
 {
-	struct regulator *supply;
+	struct regulator_dev *new_contended_rdev = NULL;
+	struct regulator_dev *old_contended_rdev = NULL;
+	int err;
+
+	mutex_lock(&regulator_list_mutex);
+
+	ww_acquire_init(ww_ctx, &regulator_ww_class);
+
+	do {
+		if (new_contended_rdev) {
+			ww_mutex_lock_slow(&new_contended_rdev->mutex, ww_ctx);
+			old_contended_rdev = new_contended_rdev;
+			old_contended_rdev->ref_cnt++;
+		}
+
+		err = regulator_lock_recursive(rdev,
+					       &new_contended_rdev,
+					       &old_contended_rdev,
+					       ww_ctx);
+
+		if (old_contended_rdev)
+			regulator_unlock(old_contended_rdev);
+
+	} while (err == -EDEADLK);
+
+	ww_acquire_done(ww_ctx);
+
+	mutex_unlock(&regulator_list_mutex);
+}
 
-	while (1) {
-		regulator_unlock(rdev);
-		supply = rdev->supply;
+/**
+ * of_get_child_regulator - get a child regulator device node
+ * based on supply name
+ * @parent: Parent device node
+ * @prop_name: Combination regulator supply name and "-supply"
+ *
+ * Traverse all child nodes.
+ * Extract the child regulator device node corresponding to the supply name.
+ * returns the device node corresponding to the regulator if found, else
+ * returns NULL.
+ */
+static struct device_node *of_get_child_regulator(struct device_node *parent,
+						  const char *prop_name)
+{
+	struct device_node *regnode = NULL;
+	struct device_node *child = NULL;
 
-		if (!rdev->supply)
-			return;
+	for_each_child_of_node(parent, child) {
+		regnode = of_parse_phandle(child, prop_name, 0);
 
-		rdev = supply->rdev;
+		if (!regnode) {
+			regnode = of_get_child_regulator(child, prop_name);
+			if (regnode)
+				return regnode;
+		} else {
+			return regnode;
+		}
 	}
+	return NULL;
 }
 
 /**
@@ -247,6 +427,10 @@ static struct device_node *of_get_regulator(struct device *dev, const char *supp
 	regnode = of_parse_phandle(dev->of_node, prop_name, 0);
 
 	if (!regnode) {
+		regnode = of_get_child_regulator(dev->of_node, prop_name);
+		if (regnode)
+			return regnode;
+
 		dev_dbg(dev, "Looking up %s property in node %pOF failed\n",
 				prop_name, dev->of_node);
 		return NULL;
@@ -582,8 +766,10 @@ static ssize_t regulator_total_uA_show(struct device *dev,
 	int uA = 0;
 
 	regulator_lock(rdev);
-	list_for_each_entry(regulator, &rdev->consumer_list, list)
-		uA += regulator->uA_load;
+	list_for_each_entry(regulator, &rdev->consumer_list, list) {
+		if (regulator->enable_count)
+			uA += regulator->uA_load;
+	}
 	regulator_unlock(rdev);
 	return sprintf(buf, "%d\n", uA);
 }
@@ -738,7 +924,7 @@ static int drms_uA_update(struct regulator_dev *rdev)
 	int current_uA = 0, output_uV, input_uV, err;
 	unsigned int mode;
 
-	lockdep_assert_held_once(&rdev->mutex);
+	lockdep_assert_held_once(&rdev->mutex.base);
 
 	/*
 	 * first check to see if we can set modes at all, otherwise just
@@ -756,8 +942,10 @@ static int drms_uA_update(struct regulator_dev *rdev)
 		return -EINVAL;
 
 	/* calc total requested load */
-	list_for_each_entry(sibling, &rdev->consumer_list, list)
-		current_uA += sibling->uA_load;
+	list_for_each_entry(sibling, &rdev->consumer_list, list) {
+		if (sibling->enable_count)
+			current_uA += sibling->uA_load;
+	}
 
 	current_uA += rdev->constraints->system_load;
 
@@ -1156,17 +1344,12 @@ static int set_machine_constraints(struct regulator_dev *rdev,
 			rdev_err(rdev, "failed to set initial mode: %d\n", ret);
 			return ret;
 		}
-	}
-
-	/* If the constraints say the regulator should be on at this point
-	 * and we have control then make sure it is enabled.
-	 */
-	if (rdev->constraints->always_on || rdev->constraints->boot_on) {
-		ret = _regulator_do_enable(rdev);
-		if (ret < 0 && ret != -EINVAL) {
-			rdev_err(rdev, "failed to enable\n");
-			return ret;
-		}
+	} else if (rdev->constraints->system_load) {
+		/*
+		 * We'll only apply the initial system load if an
+		 * initial mode wasn't specified.
+		 */
+		drms_uA_update(rdev);
 	}
 
 	if ((rdev->constraints->ramp_delay || rdev->constraints->ramp_disable)
@@ -1214,6 +1397,27 @@ static int set_machine_constraints(struct regulator_dev *rdev,
 		}
 	}
 
+	/* If the constraints say the regulator should be on at this point
+	 * and we have control then make sure it is enabled.
+	 */
+	if (rdev->constraints->always_on || rdev->constraints->boot_on) {
+		if (rdev->supply) {
+			ret = regulator_enable(rdev->supply);
+			if (ret < 0) {
+				_regulator_put(rdev->supply);
+				rdev->supply = NULL;
+				return ret;
+			}
+		}
+
+		ret = _regulator_do_enable(rdev);
+		if (ret < 0 && ret != -EINVAL) {
+			rdev_err(rdev, "failed to enable\n");
+			return ret;
+		}
+		rdev->use_count++;
+	}
+
 	print_constraints(rdev);
 	return 0;
 }
@@ -1628,8 +1832,12 @@ static int regulator_resolve_supply(struct regulator_dev *rdev)
 		return ret;
 	}
 
-	/* Cascade always-on state to supply */
-	if (_regulator_is_enabled(rdev)) {
+	/*
+	 * In set_machine_constraints() we may have turned this regulator on
+	 * but we couldn't propagate to the supply if it hadn't been resolved
+	 * yet.  Do it now.
+	 */
+	if (rdev->use_count) {
 		ret = regulator_enable(rdev->supply);
 		if (ret < 0) {
 			_regulator_put(rdev->supply);
@@ -1713,6 +1921,16 @@ struct regulator *_regulator_get(struct device *dev, const char *id,
 		return regulator;
 	}
 
+	mutex_lock(&regulator_list_mutex);
+	ret = (rdev->coupling_desc.n_resolved != rdev->coupling_desc.n_coupled);
+	mutex_unlock(&regulator_list_mutex);
+
+	if (ret != 0) {
+		regulator = ERR_PTR(-EPROBE_DEFER);
+		put_device(&rdev->dev);
+		return regulator;
+	}
+
 	ret = regulator_resolve_supply(rdev);
 	if (ret < 0) {
 		regulator = ERR_PTR(ret);
@@ -1832,6 +2050,9 @@ static void _regulator_put(struct regulator *regulator)
 
 	lockdep_assert_held_once(&regulator_list_mutex);
 
+	/* Docs say you must disable before calling regulator_put() */
+	WARN_ON(regulator->enable_count);
+
 	rdev = regulator->rdev;
 
 	debugfs_remove_recursive(regulator->debugfs);
@@ -2225,34 +2446,109 @@ static int _regulator_do_enable(struct regulator_dev *rdev)
 	return 0;
 }
 
+/**
+ * _regulator_handle_consumer_enable - handle that a consumer enabled
+ * @regulator: regulator source
+ *
+ * Some things on a regulator consumer (like the contribution towards total
+ * load on the regulator) only have an effect when the consumer wants the
+ * regulator enabled.  Explained in example with two consumers of the same
+ * regulator:
+ *   consumer A: set_load(100);       => total load = 0
+ *   consumer A: regulator_enable();  => total load = 100
+ *   consumer B: set_load(1000);      => total load = 100
+ *   consumer B: regulator_enable();  => total load = 1100
+ *   consumer A: regulator_disable(); => total_load = 1000
+ *
+ * This function (together with _regulator_handle_consumer_disable) is
+ * responsible for keeping track of the refcount for a given regulator consumer
+ * and applying / unapplying these things.
+ *
+ * Returns 0 upon no error; -error upon error.
+ */
+static int _regulator_handle_consumer_enable(struct regulator *regulator)
+{
+	struct regulator_dev *rdev = regulator->rdev;
+
+	lockdep_assert_held_once(&rdev->mutex.base);
+
+	regulator->enable_count++;
+	if (regulator->uA_load && regulator->enable_count == 1)
+		return drms_uA_update(rdev);
+
+	return 0;
+}
+
+/**
+ * _regulator_handle_consumer_disable - handle that a consumer disabled
+ * @regulator: regulator source
+ *
+ * The opposite of _regulator_handle_consumer_enable().
+ *
+ * Returns 0 upon no error; -error upon error.
+ */
+static int _regulator_handle_consumer_disable(struct regulator *regulator)
+{
+	struct regulator_dev *rdev = regulator->rdev;
+
+	lockdep_assert_held_once(&rdev->mutex.base);
+
+	if (!regulator->enable_count) {
+		rdev_err(rdev, "Underflow of regulator enable count\n");
+		return -EINVAL;
+	}
+
+	regulator->enable_count--;
+	if (regulator->uA_load && regulator->enable_count == 0)
+		return drms_uA_update(rdev);
+
+	return 0;
+}
+
 /* locks held by regulator_enable() */
-static int _regulator_enable(struct regulator_dev *rdev)
+static int _regulator_enable(struct regulator *regulator)
 {
+	struct regulator_dev *rdev = regulator->rdev;
 	int ret;
 
-	lockdep_assert_held_once(&rdev->mutex);
+	lockdep_assert_held_once(&rdev->mutex.base);
 
-	/* check voltage and requested load before enabling */
-	if (regulator_ops_is_valid(rdev, REGULATOR_CHANGE_DRMS))
-		drms_uA_update(rdev);
+	if (rdev->use_count == 0 && rdev->supply) {
+		ret = _regulator_enable(rdev->supply);
+		if (ret < 0)
+			return ret;
+	}
+
+	/* balance only if there are regulators coupled */
+	if (rdev->coupling_desc.n_coupled > 1) {
+		ret = regulator_balance_voltage(rdev, PM_SUSPEND_ON);
+		if (ret < 0)
+			goto err_disable_supply;
+	}
+
+	ret = _regulator_handle_consumer_enable(regulator);
+	if (ret < 0)
+		goto err_disable_supply;
 
 	if (rdev->use_count == 0) {
 		/* The regulator may on if it's not switchable or left on */
 		ret = _regulator_is_enabled(rdev);
 		if (ret == -EINVAL || ret == 0) {
 			if (!regulator_ops_is_valid(rdev,
-					REGULATOR_CHANGE_STATUS))
-				return -EPERM;
+					REGULATOR_CHANGE_STATUS)) {
+				ret = -EPERM;
+				goto err_consumer_disable;
+			}
 
 			ret = _regulator_do_enable(rdev);
 			if (ret < 0)
-				return ret;
+				goto err_consumer_disable;
 
 			_notifier_call_chain(rdev, REGULATOR_EVENT_ENABLE,
 					     NULL);
 		} else if (ret < 0) {
 			rdev_err(rdev, "is_enabled() failed: %d\n", ret);
-			return ret;
+			goto err_consumer_disable;
 		}
 		/* Fallthrough on positive return values - already enabled */
 	}
@@ -2260,6 +2556,15 @@ static int _regulator_enable(struct regulator_dev *rdev)
 	rdev->use_count++;
 
 	return 0;
+
+err_consumer_disable:
+	_regulator_handle_consumer_disable(regulator);
+
+err_disable_supply:
+	if (rdev->use_count == 0 && rdev->supply)
+		_regulator_disable(rdev->supply);
+
+	return ret;
 }
 
 /**
@@ -2276,23 +2581,12 @@ static int _regulator_enable(struct regulator_dev *rdev)
 int regulator_enable(struct regulator *regulator)
 {
 	struct regulator_dev *rdev = regulator->rdev;
-	int ret = 0;
-
-	if (regulator->always_on)
-		return 0;
-
-	if (rdev->supply) {
-		ret = regulator_enable(rdev->supply);
-		if (ret != 0)
-			return ret;
-	}
-
-	mutex_lock(&rdev->mutex);
-	ret = _regulator_enable(rdev);
-	mutex_unlock(&rdev->mutex);
+	struct ww_acquire_ctx ww_ctx;
+	int ret;
 
-	if (ret != 0 && rdev->supply)
-		regulator_disable(rdev->supply);
+	regulator_lock_dependent(rdev, &ww_ctx);
+	ret = _regulator_enable(regulator);
+	regulator_unlock_dependent(rdev, &ww_ctx);
 
 	return ret;
 }
@@ -2330,11 +2624,12 @@ static int _regulator_do_disable(struct regulator_dev *rdev)
 }
 
 /* locks held by regulator_disable() */
-static int _regulator_disable(struct regulator_dev *rdev)
+static int _regulator_disable(struct regulator *regulator)
 {
+	struct regulator_dev *rdev = regulator->rdev;
 	int ret = 0;
 
-	lockdep_assert_held_once(&rdev->mutex);
+	lockdep_assert_held_once(&rdev->mutex.base);
 
 	if (WARN(rdev->use_count <= 0,
 		 "unbalanced disables for %s\n", rdev_get_name(rdev)))
@@ -2366,12 +2661,18 @@ static int _regulator_disable(struct regulator_dev *rdev)
 
 		rdev->use_count = 0;
 	} else if (rdev->use_count > 1) {
-		if (regulator_ops_is_valid(rdev, REGULATOR_CHANGE_DRMS))
-			drms_uA_update(rdev);
-
 		rdev->use_count--;
 	}
 
+	if (ret == 0)
+		ret = _regulator_handle_consumer_disable(regulator);
+
+	if (ret == 0 && rdev->coupling_desc.n_coupled > 1)
+		ret = regulator_balance_voltage(rdev, PM_SUSPEND_ON);
+
+	if (ret == 0 && rdev->use_count == 0 && rdev->supply)
+		ret = _regulator_disable(rdev->supply);
+
 	return ret;
 }
 
@@ -2390,17 +2691,12 @@ static int _regulator_disable(struct regulator_dev *rdev)
 int regulator_disable(struct regulator *regulator)
 {
 	struct regulator_dev *rdev = regulator->rdev;
-	int ret = 0;
-
-	if (regulator->always_on)
-		return 0;
-
-	mutex_lock(&rdev->mutex);
-	ret = _regulator_disable(rdev);
-	mutex_unlock(&rdev->mutex);
+	struct ww_acquire_ctx ww_ctx;
+	int ret;
 
-	if (ret == 0 && rdev->supply)
-		regulator_disable(rdev->supply);
+	regulator_lock_dependent(rdev, &ww_ctx);
+	ret = _regulator_disable(regulator);
+	regulator_unlock_dependent(rdev, &ww_ctx);
 
 	return ret;
 }
@@ -2411,7 +2707,7 @@ static int _regulator_force_disable(struct regulator_dev *rdev)
 {
 	int ret = 0;
 
-	lockdep_assert_held_once(&rdev->mutex);
+	lockdep_assert_held_once(&rdev->mutex.base);
 
 	ret = _notifier_call_chain(rdev, REGULATOR_EVENT_FORCE_DISABLE |
 			REGULATOR_EVENT_PRE_DISABLE, NULL);
@@ -2444,16 +2740,25 @@ static int _regulator_force_disable(struct regulator_dev *rdev)
 int regulator_force_disable(struct regulator *regulator)
 {
 	struct regulator_dev *rdev = regulator->rdev;
+	struct ww_acquire_ctx ww_ctx;
 	int ret;
 
-	mutex_lock(&rdev->mutex);
-	regulator->uA_load = 0;
+	regulator_lock_dependent(rdev, &ww_ctx);
+
 	ret = _regulator_force_disable(regulator->rdev);
-	mutex_unlock(&rdev->mutex);
 
-	if (rdev->supply)
-		while (rdev->open_count--)
-			regulator_disable(rdev->supply);
+	if (rdev->coupling_desc.n_coupled > 1)
+		regulator_balance_voltage(rdev, PM_SUSPEND_ON);
+
+	if (regulator->uA_load) {
+		regulator->uA_load = 0;
+		ret = drms_uA_update(rdev);
+	}
+
+	if (rdev->use_count != 0 && rdev->supply)
+		_regulator_disable(rdev->supply);
+
+	regulator_unlock_dependent(rdev, &ww_ctx);
 
 	return ret;
 }
@@ -2463,14 +2768,12 @@ static void regulator_disable_work(struct work_struct *work)
 {
 	struct regulator_dev *rdev = container_of(work, struct regulator_dev,
 						  disable_work.work);
+	struct ww_acquire_ctx ww_ctx;
 	int count, i, ret;
+	struct regulator *regulator;
+	int total_count = 0;
 
-	regulator_lock(rdev);
-
-	BUG_ON(!rdev->deferred_disables);
-
-	count = rdev->deferred_disables;
-	rdev->deferred_disables = 0;
+	regulator_lock_dependent(rdev, &ww_ctx);
 
 	/*
 	 * Workqueue functions queue the new work instance while the previous
@@ -2480,23 +2783,27 @@ static void regulator_disable_work(struct work_struct *work)
 	 */
 	cancel_delayed_work(&rdev->disable_work);
 
-	for (i = 0; i < count; i++) {
-		ret = _regulator_disable(rdev);
-		if (ret != 0)
-			rdev_err(rdev, "Deferred disable failed: %d\n", ret);
-	}
+	list_for_each_entry(regulator, &rdev->consumer_list, list) {
+		count = regulator->deferred_disables;
 
-	regulator_unlock(rdev);
+		if (!count)
+			continue;
+
+		total_count += count;
+		regulator->deferred_disables = 0;
 
-	if (rdev->supply) {
 		for (i = 0; i < count; i++) {
-			ret = regulator_disable(rdev->supply);
-			if (ret != 0) {
-				rdev_err(rdev,
-					 "Supply disable failed: %d\n", ret);
-			}
+			ret = _regulator_disable(regulator);
+			if (ret != 0)
+				rdev_err(rdev, "Deferred disable failed: %d\n", ret);
 		}
 	}
+	WARN_ON(!total_count);
+
+	if (rdev->coupling_desc.n_coupled > 1)
+		regulator_balance_voltage(rdev, PM_SUSPEND_ON);
+
+	regulator_unlock_dependent(rdev, &ww_ctx);
 }
 
 /**
@@ -2515,14 +2822,11 @@ int regulator_disable_deferred(struct regulator *regulator, int ms)
 {
 	struct regulator_dev *rdev = regulator->rdev;
 
-	if (regulator->always_on)
-		return 0;
-
 	if (!ms)
 		return regulator_disable(regulator);
 
 	regulator_lock(rdev);
-	rdev->deferred_disables++;
+	regulator->deferred_disables++;
 	mod_delayed_work(system_power_efficient_wq, &rdev->disable_work,
 			 msecs_to_jiffies(ms));
 	regulator_unlock(rdev);
@@ -2597,9 +2901,9 @@ int regulator_is_enabled(struct regulator *regulator)
 	if (regulator->always_on)
 		return 1;
 
-	mutex_lock(&regulator->rdev->mutex);
+	regulator_lock(regulator->rdev);
 	ret = _regulator_is_enabled(regulator->rdev);
-	mutex_unlock(&regulator->rdev->mutex);
+	regulator_unlock(regulator->rdev);
 
 	return ret;
 }
@@ -3013,8 +3317,6 @@ static int regulator_set_voltage_unlocked(struct regulator *regulator,
 	int ret = 0;
 	int old_min_uV, old_max_uV;
 	int current_uV;
-	int best_supply_uV = 0;
-	int supply_change_uV = 0;
 
 	/* If we're setting the same range as last time the change
 	 * should be a noop (some cpufreq implementations use the same
@@ -3054,10 +3356,27 @@ static int regulator_set_voltage_unlocked(struct regulator *regulator,
 	voltage->min_uV = min_uV;
 	voltage->max_uV = max_uV;
 
-	ret = regulator_check_consumers(rdev, &min_uV, &max_uV, state);
+	/* for not coupled regulators this will just set the voltage */
+	ret = regulator_balance_voltage(rdev, state);
 	if (ret < 0)
 		goto out2;
 
+out:
+	return 0;
+out2:
+	voltage->min_uV = old_min_uV;
+	voltage->max_uV = old_max_uV;
+
+	return ret;
+}
+
+static int regulator_set_voltage_rdev(struct regulator_dev *rdev, int min_uV,
+				      int max_uV, suspend_state_t state)
+{
+	int best_supply_uV = 0;
+	int supply_change_uV = 0;
+	int ret;
+
 	if (rdev->supply &&
 	    regulator_ops_is_valid(rdev->supply->rdev,
 				   REGULATOR_CHANGE_VOLTAGE) &&
@@ -3069,13 +3388,13 @@ static int regulator_set_voltage_unlocked(struct regulator *regulator,
 		selector = regulator_map_voltage(rdev, min_uV, max_uV);
 		if (selector < 0) {
 			ret = selector;
-			goto out2;
+			goto out;
 		}
 
 		best_supply_uV = _regulator_list_voltage(rdev, selector, 0);
 		if (best_supply_uV < 0) {
 			ret = best_supply_uV;
-			goto out2;
+			goto out;
 		}
 
 		best_supply_uV += rdev->desc->min_dropout_uV;
@@ -3083,7 +3402,7 @@ static int regulator_set_voltage_unlocked(struct regulator *regulator,
 		current_supply_uV = _regulator_get_voltage(rdev->supply->rdev);
 		if (current_supply_uV < 0) {
 			ret = current_supply_uV;
-			goto out2;
+			goto out;
 		}
 
 		supply_change_uV = best_supply_uV - current_supply_uV;
@@ -3095,7 +3414,7 @@ static int regulator_set_voltage_unlocked(struct regulator *regulator,
 		if (ret) {
 			dev_err(&rdev->dev, "Failed to increase supply voltage: %d\n",
 					ret);
-			goto out2;
+			goto out;
 		}
 	}
 
@@ -3105,7 +3424,7 @@ static int regulator_set_voltage_unlocked(struct regulator *regulator,
 		ret = _regulator_do_set_suspend_voltage(rdev, min_uV,
 							max_uV, state);
 	if (ret < 0)
-		goto out2;
+		goto out;
 
 	if (supply_change_uV < 0) {
 		ret = regulator_set_voltage_unlocked(rdev->supply,
@@ -3119,10 +3438,273 @@ static int regulator_set_voltage_unlocked(struct regulator *regulator,
 
 out:
 	return ret;
-out2:
-	voltage->min_uV = old_min_uV;
-	voltage->max_uV = old_max_uV;
+}
+
+static int regulator_limit_voltage_step(struct regulator_dev *rdev,
+					int *current_uV, int *min_uV)
+{
+	struct regulation_constraints *constraints = rdev->constraints;
+
+	/* Limit voltage change only if necessary */
+	if (!constraints->max_uV_step || !_regulator_is_enabled(rdev))
+		return 1;
+
+	if (*current_uV < 0) {
+		*current_uV = _regulator_get_voltage(rdev);
+
+		if (*current_uV < 0)
+			return *current_uV;
+	}
+
+	if (abs(*current_uV - *min_uV) <= constraints->max_uV_step)
+		return 1;
+
+	/* Clamp target voltage within the given step */
+	if (*current_uV < *min_uV)
+		*min_uV = min(*current_uV + constraints->max_uV_step,
+			      *min_uV);
+	else
+		*min_uV = max(*current_uV - constraints->max_uV_step,
+			      *min_uV);
+
+	return 0;
+}
+
+static int regulator_get_optimal_voltage(struct regulator_dev *rdev,
+					 int *current_uV,
+					 int *min_uV, int *max_uV,
+					 suspend_state_t state,
+					 int n_coupled)
+{
+	struct coupling_desc *c_desc = &rdev->coupling_desc;
+	struct regulator_dev **c_rdevs = c_desc->coupled_rdevs;
+	struct regulation_constraints *constraints = rdev->constraints;
+	int max_spread = constraints->max_spread;
+	int desired_min_uV = 0, desired_max_uV = INT_MAX;
+	int max_current_uV = 0, min_current_uV = INT_MAX;
+	int highest_min_uV = 0, target_uV, possible_uV;
+	int i, ret;
+	bool done;
+
+	*current_uV = -1;
+
+	/*
+	 * If there are no coupled regulators, simply set the voltage
+	 * demanded by consumers.
+	 */
+	if (n_coupled == 1) {
+		/*
+		 * If consumers don't provide any demands, set voltage
+		 * to min_uV
+		 */
+		desired_min_uV = constraints->min_uV;
+		desired_max_uV = constraints->max_uV;
+
+		ret = regulator_check_consumers(rdev,
+						&desired_min_uV,
+						&desired_max_uV, state);
+		if (ret < 0)
+			return ret;
+
+		possible_uV = desired_min_uV;
+		done = true;
+
+		goto finish;
+	}
+
+	/* Find highest min desired voltage */
+	for (i = 0; i < n_coupled; i++) {
+		int tmp_min = 0;
+		int tmp_max = INT_MAX;
+
+		lockdep_assert_held_once(&c_rdevs[i]->mutex.base);
+
+		ret = regulator_check_consumers(c_rdevs[i],
+						&tmp_min,
+						&tmp_max, state);
+		if (ret < 0)
+			return ret;
+
+		ret = regulator_check_voltage(c_rdevs[i], &tmp_min, &tmp_max);
+		if (ret < 0)
+			return ret;
+
+		highest_min_uV = max(highest_min_uV, tmp_min);
+
+		if (i == 0) {
+			desired_min_uV = tmp_min;
+			desired_max_uV = tmp_max;
+		}
+	}
+
+	/*
+	 * Let target_uV be equal to the desired one if possible.
+	 * If not, set it to minimum voltage, allowed by other coupled
+	 * regulators.
+	 */
+	target_uV = max(desired_min_uV, highest_min_uV - max_spread);
+
+	/*
+	 * Find min and max voltages, which currently aren't violating
+	 * max_spread.
+	 */
+	for (i = 1; i < n_coupled; i++) {
+		int tmp_act;
+
+		if (!_regulator_is_enabled(c_rdevs[i]))
+			continue;
+
+		tmp_act = _regulator_get_voltage(c_rdevs[i]);
+		if (tmp_act < 0)
+			return tmp_act;
+
+		min_current_uV = min(tmp_act, min_current_uV);
+		max_current_uV = max(tmp_act, max_current_uV);
+	}
+
+	/* There aren't any other regulators enabled */
+	if (max_current_uV == 0) {
+		possible_uV = target_uV;
+	} else {
+		/*
+		 * Correct target voltage, so as it currently isn't
+		 * violating max_spread
+		 */
+		possible_uV = max(target_uV, max_current_uV - max_spread);
+		possible_uV = min(possible_uV, min_current_uV + max_spread);
+	}
+
+	if (possible_uV > desired_max_uV)
+		return -EINVAL;
+
+	done = (possible_uV == target_uV);
+	desired_min_uV = possible_uV;
 
+finish:
+	/* Apply max_uV_step constraint if necessary */
+	if (state == PM_SUSPEND_ON) {
+		ret = regulator_limit_voltage_step(rdev, current_uV,
+						   &desired_min_uV);
+		if (ret < 0)
+			return ret;
+
+		if (ret == 0)
+			done = false;
+	}
+
+	/* Set current_uV if wasn't done earlier in the code and if necessary */
+	if (n_coupled > 1 && *current_uV == -1) {
+
+		if (_regulator_is_enabled(rdev)) {
+			ret = _regulator_get_voltage(rdev);
+			if (ret < 0)
+				return ret;
+
+			*current_uV = ret;
+		} else {
+			*current_uV = desired_min_uV;
+		}
+	}
+
+	*min_uV = desired_min_uV;
+	*max_uV = desired_max_uV;
+
+	return done;
+}
+
+static int regulator_balance_voltage(struct regulator_dev *rdev,
+				     suspend_state_t state)
+{
+	struct regulator_dev **c_rdevs;
+	struct regulator_dev *best_rdev;
+	struct coupling_desc *c_desc = &rdev->coupling_desc;
+	int i, ret, n_coupled, best_min_uV, best_max_uV, best_c_rdev;
+	bool best_c_rdev_done, c_rdev_done[MAX_COUPLED];
+	unsigned int delta, best_delta;
+
+	c_rdevs = c_desc->coupled_rdevs;
+	n_coupled = c_desc->n_coupled;
+
+	/*
+	 * If system is in a state other than PM_SUSPEND_ON, don't check
+	 * other coupled regulators.
+	 */
+	if (state != PM_SUSPEND_ON)
+		n_coupled = 1;
+
+	if (c_desc->n_resolved < n_coupled) {
+		rdev_err(rdev, "Not all coupled regulators registered\n");
+		return -EPERM;
+	}
+
+	for (i = 0; i < n_coupled; i++)
+		c_rdev_done[i] = false;
+
+	/*
+	 * Find the best possible voltage change on each loop. Leave the loop
+	 * if there isn't any possible change.
+	 */
+	do {
+		best_c_rdev_done = false;
+		best_delta = 0;
+		best_min_uV = 0;
+		best_max_uV = 0;
+		best_c_rdev = 0;
+		best_rdev = NULL;
+
+		/*
+		 * Find highest difference between optimal voltage
+		 * and current voltage.
+		 */
+		for (i = 0; i < n_coupled; i++) {
+			/*
+			 * optimal_uV is the best voltage that can be set for
+			 * i-th regulator at the moment without violating
+			 * max_spread constraint in order to balance
+			 * the coupled voltages.
+			 */
+			int optimal_uV = 0, optimal_max_uV = 0, current_uV = 0;
+
+			if (c_rdev_done[i])
+				continue;
+
+			ret = regulator_get_optimal_voltage(c_rdevs[i],
+							    &current_uV,
+							    &optimal_uV,
+							    &optimal_max_uV,
+							    state, n_coupled);
+			if (ret < 0)
+				goto out;
+
+			delta = abs(optimal_uV - current_uV);
+
+			if (delta && best_delta <= delta) {
+				best_c_rdev_done = ret;
+				best_delta = delta;
+				best_rdev = c_rdevs[i];
+				best_min_uV = optimal_uV;
+				best_max_uV = optimal_max_uV;
+				best_c_rdev = i;
+			}
+		}
+
+		/* Nothing to change, return successfully */
+		if (!best_rdev) {
+			ret = 0;
+			goto out;
+		}
+
+		ret = regulator_set_voltage_rdev(best_rdev, best_min_uV,
+						 best_max_uV, state);
+
+		if (ret < 0)
+			goto out;
+
+		c_rdev_done[best_c_rdev] = best_c_rdev_done;
+
+	} while (n_coupled > 1);
+
+out:
 	return ret;
 }
 
@@ -3146,14 +3728,15 @@ static int regulator_set_voltage_unlocked(struct regulator *regulator,
  */
 int regulator_set_voltage(struct regulator *regulator, int min_uV, int max_uV)
 {
-	int ret = 0;
+	struct ww_acquire_ctx ww_ctx;
+	int ret;
 
-	regulator_lock_supply(regulator->rdev);
+	regulator_lock_dependent(regulator->rdev, &ww_ctx);
 
 	ret = regulator_set_voltage_unlocked(regulator, min_uV, max_uV,
 					     PM_SUSPEND_ON);
 
-	regulator_unlock_supply(regulator->rdev);
+	regulator_unlock_dependent(regulator->rdev, &ww_ctx);
 
 	return ret;
 }
@@ -3225,18 +3808,19 @@ static int _regulator_set_suspend_voltage(struct regulator *regulator,
 int regulator_set_suspend_voltage(struct regulator *regulator, int min_uV,
 				  int max_uV, suspend_state_t state)
 {
-	int ret = 0;
+	struct ww_acquire_ctx ww_ctx;
+	int ret;
 
 	/* PM_SUSPEND_ON is handled by regulator_set_voltage() */
 	if (regulator_check_states(state) || state == PM_SUSPEND_ON)
 		return -EINVAL;
 
-	regulator_lock_supply(regulator->rdev);
+	regulator_lock_dependent(regulator->rdev, &ww_ctx);
 
 	ret = _regulator_set_suspend_voltage(regulator, min_uV,
 					     max_uV, state);
 
-	regulator_unlock_supply(regulator->rdev);
+	regulator_unlock_dependent(regulator->rdev, &ww_ctx);
 
 	return ret;
 }
@@ -3426,13 +4010,12 @@ static int _regulator_get_voltage(struct regulator_dev *rdev)
  */
 int regulator_get_voltage(struct regulator *regulator)
 {
+	struct ww_acquire_ctx ww_ctx;
 	int ret;
 
-	regulator_lock_supply(regulator->rdev);
-
+	regulator_lock_dependent(regulator->rdev, &ww_ctx);
 	ret = _regulator_get_voltage(regulator->rdev);
-
-	regulator_unlock_supply(regulator->rdev);
+	regulator_unlock_dependent(regulator->rdev, &ww_ctx);
 
 	return ret;
 }
@@ -3650,16 +4233,30 @@ EXPORT_SYMBOL_GPL(regulator_get_error_flags);
  * DRMS will sum the total requested load on the regulator and change
  * to the most efficient operating mode if platform constraints allow.
  *
+ * NOTE: when a regulator consumer requests to have a regulator
+ * disabled then any load that consumer requested no longer counts
+ * toward the total requested load.  If the regulator is re-enabled
+ * then the previously requested load will start counting again.
+ *
+ * If a regulator is an always-on regulator then an individual consumer's
+ * load will still be removed if that consumer is fully disabled.
+ *
  * On error a negative errno is returned.
  */
 int regulator_set_load(struct regulator *regulator, int uA_load)
 {
 	struct regulator_dev *rdev = regulator->rdev;
-	int ret;
+	int old_uA_load;
+	int ret = 0;
 
 	regulator_lock(rdev);
+	old_uA_load = regulator->uA_load;
 	regulator->uA_load = uA_load;
-	ret = drms_uA_update(rdev);
+	if (regulator->enable_count && old_uA_load != uA_load) {
+		ret = drms_uA_update(rdev);
+		if (ret < 0)
+			regulator->uA_load = old_uA_load;
+	}
 	regulator_unlock(rdev);
 
 	return ret;
@@ -3830,11 +4427,8 @@ int regulator_bulk_enable(int num_consumers,
 	int ret = 0;
 
 	for (i = 0; i < num_consumers; i++) {
-		if (consumers[i].consumer->always_on)
-			consumers[i].ret = 0;
-		else
-			async_schedule_domain(regulator_bulk_enable_async,
-					      &consumers[i], &async_domain);
+		async_schedule_domain(regulator_bulk_enable_async,
+				      &consumers[i], &async_domain);
 	}
 
 	async_synchronize_full_domain(&async_domain);
@@ -3968,7 +4562,7 @@ EXPORT_SYMBOL_GPL(regulator_bulk_free);
 int regulator_notifier_call_chain(struct regulator_dev *rdev,
 				  unsigned long event, void *data)
 {
-	lockdep_assert_held_once(&rdev->mutex);
+	lockdep_assert_held_once(&rdev->mutex.base);
 
 	_notifier_call_chain(rdev, event, data);
 	return NOTIFY_DONE;
@@ -4070,10 +4664,6 @@ static umode_t regulator_attr_is_visible(struct kobject *kobj,
 	if (attr == &dev_attr_bypass.attr)
 		return ops->get_bypass ? mode : 0;
 
-	/* some attributes are type-specific */
-	if (attr == &dev_attr_requested_microamps.attr)
-		return rdev->desc->type == REGULATOR_CURRENT ? mode : 0;
-
 	/* constraints need specific supporting methods */
 	if (attr == &dev_attr_min_microvolts.attr ||
 	    attr == &dev_attr_max_microvolts.attr)
@@ -4157,7 +4747,7 @@ static int regulator_register_resolve_supply(struct device *dev, void *data)
 	return 0;
 }
 
-static int regulator_fill_coupling_array(struct regulator_dev *rdev)
+static void regulator_resolve_coupling(struct regulator_dev *rdev)
 {
 	struct coupling_desc *c_desc = &rdev->coupling_desc;
 	int n_coupled = c_desc->n_coupled;
@@ -4171,33 +4761,58 @@ static int regulator_fill_coupling_array(struct regulator_dev *rdev)
 
 		c_rdev = of_parse_coupled_regulator(rdev, i - 1);
 
-		if (c_rdev) {
-			c_desc->coupled_rdevs[i] = c_rdev;
-			c_desc->n_resolved++;
-		}
-	}
+		if (!c_rdev)
+			continue;
 
-	if (rdev->coupling_desc.n_resolved < n_coupled)
-		return -1;
-	else
-		return 0;
+		regulator_lock(c_rdev);
+
+		c_desc->coupled_rdevs[i] = c_rdev;
+		c_desc->n_resolved++;
+
+		regulator_unlock(c_rdev);
+
+		regulator_resolve_coupling(c_rdev);
+	}
 }
 
-static int regulator_register_fill_coupling_array(struct device *dev,
-						  void *data)
+static void regulator_remove_coupling(struct regulator_dev *rdev)
 {
-	struct regulator_dev *rdev = dev_to_rdev(dev);
+	struct coupling_desc *__c_desc, *c_desc = &rdev->coupling_desc;
+	struct regulator_dev *__c_rdev, *c_rdev;
+	unsigned int __n_coupled, n_coupled;
+	int i, k;
 
-	if (!IS_ENABLED(CONFIG_OF))
-		return 0;
+	n_coupled = c_desc->n_coupled;
 
-	if (regulator_fill_coupling_array(rdev))
-		rdev_dbg(rdev, "unable to resolve coupling\n");
+	for (i = 1; i < n_coupled; i++) {
+		c_rdev = c_desc->coupled_rdevs[i];
 
-	return 0;
+		if (!c_rdev)
+			continue;
+
+		regulator_lock(c_rdev);
+
+		__c_desc = &c_rdev->coupling_desc;
+		__n_coupled = __c_desc->n_coupled;
+
+		for (k = 1; k < __n_coupled; k++) {
+			__c_rdev = __c_desc->coupled_rdevs[k];
+
+			if (__c_rdev == rdev) {
+				__c_desc->coupled_rdevs[k] = NULL;
+				__c_desc->n_resolved--;
+				break;
+			}
+		}
+
+		regulator_unlock(c_rdev);
+
+		c_desc->coupled_rdevs[i] = NULL;
+		c_desc->n_resolved--;
+	}
 }
 
-static int regulator_resolve_coupling(struct regulator_dev *rdev)
+static int regulator_init_coupling(struct regulator_dev *rdev)
 {
 	int n_phandles;
 
@@ -4237,13 +4852,6 @@ static int regulator_resolve_coupling(struct regulator_dev *rdev)
 	if (!of_check_coupling_data(rdev))
 		return -EPERM;
 
-	/*
-	 * After everything has been checked, try to fill rdevs array
-	 * with pointers to regulators parsed from device tree. If some
-	 * regulators are not registered yet, retry in late init call
-	 */
-	regulator_fill_coupling_array(rdev);
-
 	return 0;
 }
 
@@ -4265,21 +4873,33 @@ regulator_register(const struct regulator_desc *regulator_desc,
 	struct regulator_config *config = NULL;
 	static atomic_t regulator_no = ATOMIC_INIT(-1);
 	struct regulator_dev *rdev;
+	bool dangling_cfg_gpiod = false;
+	bool dangling_of_gpiod = false;
 	struct device *dev;
 	int ret, i;
 
-	if (regulator_desc == NULL || cfg == NULL)
+	if (cfg == NULL)
 		return ERR_PTR(-EINVAL);
+	if (cfg->ena_gpiod)
+		dangling_cfg_gpiod = true;
+	if (regulator_desc == NULL) {
+		ret = -EINVAL;
+		goto rinse;
+	}
 
 	dev = cfg->dev;
 	WARN_ON(!dev);
 
-	if (regulator_desc->name == NULL || regulator_desc->ops == NULL)
-		return ERR_PTR(-EINVAL);
+	if (regulator_desc->name == NULL || regulator_desc->ops == NULL) {
+		ret = -EINVAL;
+		goto rinse;
+	}
 
 	if (regulator_desc->type != REGULATOR_VOLTAGE &&
-	    regulator_desc->type != REGULATOR_CURRENT)
-		return ERR_PTR(-EINVAL);
+	    regulator_desc->type != REGULATOR_CURRENT) {
+		ret = -EINVAL;
+		goto rinse;
+	}
 
 	/* Only one of each should be implemented */
 	WARN_ON(regulator_desc->ops->get_voltage &&
@@ -4290,16 +4910,20 @@ regulator_register(const struct regulator_desc *regulator_desc,
 	/* If we're using selectors we must implement list_voltage. */
 	if (regulator_desc->ops->get_voltage_sel &&
 	    !regulator_desc->ops->list_voltage) {
-		return ERR_PTR(-EINVAL);
+		ret = -EINVAL;
+		goto rinse;
 	}
 	if (regulator_desc->ops->set_voltage_sel &&
 	    !regulator_desc->ops->list_voltage) {
-		return ERR_PTR(-EINVAL);
+		ret = -EINVAL;
+		goto rinse;
 	}
 
 	rdev = kzalloc(sizeof(struct regulator_dev), GFP_KERNEL);
-	if (rdev == NULL)
-		return ERR_PTR(-ENOMEM);
+	if (rdev == NULL) {
+		ret = -ENOMEM;
+		goto rinse;
+	}
 
 	/*
 	 * Duplicate the config so the driver could override it after
@@ -4308,17 +4932,28 @@ regulator_register(const struct regulator_desc *regulator_desc,
 	config = kmemdup(cfg, sizeof(*cfg), GFP_KERNEL);
 	if (config == NULL) {
 		kfree(rdev);
-		return ERR_PTR(-ENOMEM);
+		ret = -ENOMEM;
+		goto rinse;
 	}
 
 	init_data = regulator_of_get_init_data(dev, regulator_desc, config,
 					       &rdev->dev.of_node);
+	/*
+	 * We need to keep track of any GPIO descriptor coming from the
+	 * device tree until we have handled it over to the core. If the
+	 * config that was passed in to this function DOES NOT contain
+	 * a descriptor, and the config after this call DOES contain
+	 * a descriptor, we definately got one from parsing the device
+	 * tree.
+	 */
+	if (!cfg->ena_gpiod && config->ena_gpiod)
+		dangling_of_gpiod = true;
 	if (!init_data) {
 		init_data = config->init_data;
 		rdev->dev.of_node = of_node_get(config->of_node);
 	}
 
-	mutex_init(&rdev->mutex);
+	ww_mutex_init(&rdev->mutex, &regulator_ww_class);
 	rdev->reg_data = config->driver_data;
 	rdev->owner = regulator_desc->owner;
 	rdev->desc = regulator_desc;
@@ -4351,6 +4986,9 @@ regulator_register(const struct regulator_desc *regulator_desc,
 				 config->ena_gpio, ret);
 			goto clean;
 		}
+		/* The regulator core took over the GPIO descriptor */
+		dangling_cfg_gpiod = false;
+		dangling_of_gpiod = false;
 	}
 
 	/* register with sysfs */
@@ -4380,11 +5018,8 @@ regulator_register(const struct regulator_desc *regulator_desc,
 	if (ret < 0)
 		goto wash;
 
-	mutex_lock(&regulator_list_mutex);
-	ret = regulator_resolve_coupling(rdev);
-	mutex_unlock(&regulator_list_mutex);
-
-	if (ret != 0)
+	ret = regulator_init_coupling(rdev);
+	if (ret < 0)
 		goto wash;
 
 	/* add consumers devices */
@@ -4418,6 +5053,11 @@ regulator_register(const struct regulator_desc *regulator_desc,
 
 	rdev_init_debugfs(rdev);
 
+	/* try to resolve regulators coupling since a new one was registered */
+	mutex_lock(&regulator_list_mutex);
+	regulator_resolve_coupling(rdev);
+	mutex_unlock(&regulator_list_mutex);
+
 	/* try to resolve regulators supply since a new one was registered */
 	class_for_each_device(&regulator_class, NULL, NULL,
 			      regulator_register_resolve_supply);
@@ -4434,8 +5074,13 @@ regulator_register(const struct regulator_desc *regulator_desc,
 	regulator_ena_gpio_free(rdev);
 	mutex_unlock(&regulator_list_mutex);
 clean:
+	if (dangling_of_gpiod)
+		gpiod_put(config->ena_gpiod);
 	kfree(rdev);
 	kfree(config);
+rinse:
+	if (dangling_cfg_gpiod)
+		gpiod_put(cfg->ena_gpiod);
 	return ERR_PTR(ret);
 }
 EXPORT_SYMBOL_GPL(regulator_register);
@@ -4456,15 +5101,19 @@ void regulator_unregister(struct regulator_dev *rdev)
 			regulator_disable(rdev->supply);
 		regulator_put(rdev->supply);
 	}
+
 	mutex_lock(&regulator_list_mutex);
+
 	debugfs_remove_recursive(rdev->debugfs);
 	flush_work(&rdev->disable_work.work);
 	WARN_ON(rdev->open_count);
+	regulator_remove_coupling(rdev);
 	unset_regulator_supplies(rdev);
 	list_del(&rdev->list);
 	regulator_ena_gpio_free(rdev);
-	mutex_unlock(&regulator_list_mutex);
 	device_unregister(&rdev->dev);
+
+	mutex_unlock(&regulator_list_mutex);
 }
 EXPORT_SYMBOL_GPL(regulator_unregister);
 
@@ -4621,23 +5270,8 @@ static int supply_map_show(struct seq_file *sf, void *data)
 
 	return 0;
 }
+DEFINE_SHOW_ATTRIBUTE(supply_map);
 
-static int supply_map_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, supply_map_show, inode->i_private);
-}
-#endif
-
-static const struct file_operations supply_map_fops = {
-#ifdef CONFIG_DEBUG_FS
-	.open = supply_map_open,
-	.read = seq_read,
-	.llseek = seq_lseek,
-	.release = single_release,
-#endif
-};
-
-#ifdef CONFIG_DEBUG_FS
 struct summary_data {
 	struct seq_file *s;
 	struct regulator_dev *parent;
@@ -4672,8 +5306,6 @@ static void regulator_summary_show_subtree(struct seq_file *s,
 	if (!rdev)
 		return;
 
-	regulator_lock_nested(rdev, level);
-
 	opmode = _regulator_get_mode_unlocked(rdev);
 	seq_printf(s, "%*s%-*s %3d %4d %6d %7s ",
 		   level * 3 + 1, "",
@@ -4712,8 +5344,11 @@ static void regulator_summary_show_subtree(struct seq_file *s,
 
 		switch (rdev->desc->type) {
 		case REGULATOR_VOLTAGE:
-			seq_printf(s, "%37dmA %5dmV %5dmV",
+			seq_printf(s, "%3d %33dmA%c%5dmV %5dmV",
+				   consumer->enable_count,
 				   consumer->uA_load / 1000,
+				   consumer->uA_load && !consumer->enable_count ?
+				   '*' : ' ',
 				   consumer->voltage[PM_SUSPEND_ON].min_uV / 1000,
 				   consumer->voltage[PM_SUSPEND_ON].max_uV / 1000);
 			break;
@@ -4730,8 +5365,105 @@ static void regulator_summary_show_subtree(struct seq_file *s,
 
 	class_for_each_device(&regulator_class, NULL, &summary_data,
 			      regulator_summary_show_children);
+}
+
+struct summary_lock_data {
+	struct ww_acquire_ctx *ww_ctx;
+	struct regulator_dev **new_contended_rdev;
+	struct regulator_dev **old_contended_rdev;
+};
+
+static int regulator_summary_lock_one(struct device *dev, void *data)
+{
+	struct regulator_dev *rdev = dev_to_rdev(dev);
+	struct summary_lock_data *lock_data = data;
+	int ret = 0;
+
+	if (rdev != *lock_data->old_contended_rdev) {
+		ret = regulator_lock_nested(rdev, lock_data->ww_ctx);
+
+		if (ret == -EDEADLK)
+			*lock_data->new_contended_rdev = rdev;
+		else
+			WARN_ON_ONCE(ret);
+	} else {
+		*lock_data->old_contended_rdev = NULL;
+	}
+
+	return ret;
+}
+
+static int regulator_summary_unlock_one(struct device *dev, void *data)
+{
+	struct regulator_dev *rdev = dev_to_rdev(dev);
+	struct summary_lock_data *lock_data = data;
+
+	if (lock_data) {
+		if (rdev == *lock_data->new_contended_rdev)
+			return -EDEADLK;
+	}
 
 	regulator_unlock(rdev);
+
+	return 0;
+}
+
+static int regulator_summary_lock_all(struct ww_acquire_ctx *ww_ctx,
+				      struct regulator_dev **new_contended_rdev,
+				      struct regulator_dev **old_contended_rdev)
+{
+	struct summary_lock_data lock_data;
+	int ret;
+
+	lock_data.ww_ctx = ww_ctx;
+	lock_data.new_contended_rdev = new_contended_rdev;
+	lock_data.old_contended_rdev = old_contended_rdev;
+
+	ret = class_for_each_device(&regulator_class, NULL, &lock_data,
+				    regulator_summary_lock_one);
+	if (ret)
+		class_for_each_device(&regulator_class, NULL, &lock_data,
+				      regulator_summary_unlock_one);
+
+	return ret;
+}
+
+static void regulator_summary_lock(struct ww_acquire_ctx *ww_ctx)
+{
+	struct regulator_dev *new_contended_rdev = NULL;
+	struct regulator_dev *old_contended_rdev = NULL;
+	int err;
+
+	mutex_lock(&regulator_list_mutex);
+
+	ww_acquire_init(ww_ctx, &regulator_ww_class);
+
+	do {
+		if (new_contended_rdev) {
+			ww_mutex_lock_slow(&new_contended_rdev->mutex, ww_ctx);
+			old_contended_rdev = new_contended_rdev;
+			old_contended_rdev->ref_cnt++;
+		}
+
+		err = regulator_summary_lock_all(ww_ctx,
+						 &new_contended_rdev,
+						 &old_contended_rdev);
+
+		if (old_contended_rdev)
+			regulator_unlock(old_contended_rdev);
+
+	} while (err == -EDEADLK);
+
+	ww_acquire_done(ww_ctx);
+}
+
+static void regulator_summary_unlock(struct ww_acquire_ctx *ww_ctx)
+{
+	class_for_each_device(&regulator_class, NULL, NULL,
+			      regulator_summary_unlock_one);
+	ww_acquire_fini(ww_ctx);
+
+	mutex_unlock(&regulator_list_mutex);
 }
 
 static int regulator_summary_show_roots(struct device *dev, void *data)
@@ -4747,29 +5479,22 @@ static int regulator_summary_show_roots(struct device *dev, void *data)
 
 static int regulator_summary_show(struct seq_file *s, void *data)
 {
+	struct ww_acquire_ctx ww_ctx;
+
 	seq_puts(s, " regulator                      use open bypass  opmode voltage current     min     max\n");
 	seq_puts(s, "---------------------------------------------------------------------------------------\n");
 
+	regulator_summary_lock(&ww_ctx);
+
 	class_for_each_device(&regulator_class, NULL, s,
 			      regulator_summary_show_roots);
 
-	return 0;
-}
+	regulator_summary_unlock(&ww_ctx);
 
-static int regulator_summary_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, regulator_summary_show, inode->i_private);
+	return 0;
 }
-#endif
-
-static const struct file_operations regulator_summary_fops = {
-#ifdef CONFIG_DEBUG_FS
-	.open		= regulator_summary_open,
-	.read		= seq_read,
-	.llseek		= seq_lseek,
-	.release	= single_release,
-#endif
-};
+DEFINE_SHOW_ATTRIBUTE(regulator_summary);
+#endif /* CONFIG_DEBUG_FS */
 
 static int __init regulator_init(void)
 {
@@ -4781,12 +5506,13 @@ static int __init regulator_init(void)
 	if (!debugfs_root)
 		pr_warn("regulator: Failed to create debugfs directory\n");
 
+#ifdef CONFIG_DEBUG_FS
 	debugfs_create_file("supply_map", 0444, debugfs_root, NULL,
 			    &supply_map_fops);
 
 	debugfs_create_file("regulator_summary", 0444, debugfs_root,
 			    NULL, &regulator_summary_fops);
-
+#endif
 	regulator_dummy_init();
 
 	return ret;
@@ -4873,9 +5599,6 @@ static int __init regulator_init_complete(void)
 	class_for_each_device(&regulator_class, NULL, NULL,
 			      regulator_late_cleanup);
 
-	class_for_each_device(&regulator_class, NULL, NULL,
-			      regulator_register_fill_coupling_array);
-
 	return 0;
 }
 late_initcall_sync(regulator_init_complete);

drivers/regulator/da9052-regulator.c

@@ -435,7 +435,7 @@ static int da9052_regulator_probe(struct platform_device *pdev)
 			return -ENODEV;
 
 		for_each_child_of_node(nproot, np) {
-			if (!of_node_cmp(np->name,
+			if (of_node_name_eq(np,
 					 regulator->info->reg_desc.name)) {
 				config.init_data = of_get_regulator_init_data(
 					&pdev->dev, np,

drivers/regulator/da9210-regulator.c

@@ -131,7 +131,7 @@ static irqreturn_t da9210_irq_handler(int irq, void *data)
 	if (error < 0)
 		goto error_i2c;
 
-	mutex_lock(&chip->rdev->mutex);
+	regulator_lock(chip->rdev);
 
 	if (val & DA9210_E_OVCURR) {
 		regulator_notifier_call_chain(chip->rdev,
@@ -157,7 +157,7 @@ static irqreturn_t da9210_irq_handler(int irq, void *data)
 		handled |= DA9210_E_VMAX;
 	}
 
-	mutex_unlock(&chip->rdev->mutex);
+	regulator_unlock(chip->rdev);
 
 	if (handled) {
 		/* Clear handled events */

drivers/regulator/da9211-regulator.c

@@ -389,6 +389,12 @@ static int da9211_regulator_init(struct da9211 *chip)
 		else
 			config.ena_gpiod = NULL;
 
+		/*
+		 * Hand the GPIO descriptor management over to the regulator
+		 * core, remove it from GPIO devres management.
+		 */
+		if (config.ena_gpiod)
+			devm_gpiod_unhinge(chip->dev, config.ena_gpiod);
 		chip->rdev[i] = devm_regulator_register(chip->dev,
 			&da9211_regulators[i], &config);
 		if (IS_ERR(chip->rdev[i])) {

drivers/regulator/dbx500-prcmu.c

@@ -75,7 +75,7 @@ static struct ux500_regulator_debug {
 	u8 *state_after_suspend;
 } rdebug;
 
-static int ux500_regulator_power_state_cnt_print(struct seq_file *s, void *p)
+static int ux500_regulator_power_state_cnt_show(struct seq_file *s, void *p)
 {
 	/* print power state count */
 	seq_printf(s, "ux500-regulator power state count: %i\n",
@@ -83,23 +83,9 @@ static int ux500_regulator_power_state_cnt_print(struct seq_file *s, void *p)
 
 	return 0;
 }
+DEFINE_SHOW_ATTRIBUTE(ux500_regulator_power_state_cnt);
 
-static int ux500_regulator_power_state_cnt_open(struct inode *inode,
-	struct file *file)
-{
-	return single_open(file, ux500_regulator_power_state_cnt_print,
-		inode->i_private);
-}
-
-static const struct file_operations ux500_regulator_power_state_cnt_fops = {
-	.open = ux500_regulator_power_state_cnt_open,
-	.read = seq_read,
-	.llseek = seq_lseek,
-	.release = single_release,
-	.owner = THIS_MODULE,
-};
-
-static int ux500_regulator_status_print(struct seq_file *s, void *p)
+static int ux500_regulator_status_show(struct seq_file *s, void *p)
 {
 	int i;
 
@@ -122,20 +108,7 @@ static int ux500_regulator_status_print(struct seq_file *s, void *p)
 
 	return 0;
 }
-
-static int ux500_regulator_status_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, ux500_regulator_status_print,
-		inode->i_private);
-}
-
-static const struct file_operations ux500_regulator_status_fops = {
-	.open = ux500_regulator_status_open,
-	.read = seq_read,
-	.llseek = seq_lseek,
-	.release = single_release,
-	.owner = THIS_MODULE,
-};
+DEFINE_SHOW_ATTRIBUTE(ux500_regulator_status);
 
 int __attribute__((weak)) dbx500_regulator_testcase(
 	struct dbx500_regulator_info *regulator_info,

drivers/regulator/fixed.c

@@ -183,7 +183,11 @@ static int reg_fixed_voltage_probe(struct platform_device *pdev)
 	 */
 	gflags |= GPIOD_FLAGS_BIT_NONEXCLUSIVE;
 
-	cfg.ena_gpiod = devm_gpiod_get_optional(&pdev->dev, NULL, gflags);
+	/*
+	 * Do not use devm* here: the regulator core takes over the
+	 * lifecycle management of the GPIO descriptor.
+	 */
+	cfg.ena_gpiod = gpiod_get_optional(&pdev->dev, NULL, gflags);
 	if (IS_ERR(cfg.ena_gpiod))
 		return PTR_ERR(cfg.ena_gpiod);
 

drivers/regulator/internal.h

@@ -42,6 +42,8 @@ struct regulator {
 	unsigned int always_on:1;
 	unsigned int bypass:1;
 	int uA_load;
+	unsigned int enable_count;
+	unsigned int deferred_disables;
 	struct regulator_voltage voltage[REGULATOR_STATES_NUM];
 	const char *supply_name;
 	struct device_attribute dev_attr;

drivers/regulator/lm363x-regulator.c

@@ -224,13 +224,15 @@ static struct gpio_desc *lm363x_regulator_of_get_enable_gpio(struct device *dev,
 	/*
 	 * Check LCM_EN1/2_GPIO is configured.
 	 * Those pins are used for enabling VPOS/VNEG LDOs.
+	 * Do not use devm* here: the regulator core takes over the
+	 * lifecycle management of the GPIO descriptor.
 	 */
 	switch (id) {
 	case LM3632_LDO_POS:
-		return devm_gpiod_get_index_optional(dev, "enable", 0,
+		return gpiod_get_index_optional(dev, "enable", 0,
 				GPIOD_OUT_LOW | GPIOD_FLAGS_BIT_NONEXCLUSIVE);
 	case LM3632_LDO_NEG:
-		return devm_gpiod_get_index_optional(dev, "enable", 1,
+		return gpiod_get_index_optional(dev, "enable", 1,
 				GPIOD_OUT_LOW | GPIOD_FLAGS_BIT_NONEXCLUSIVE);
 	default:
 		return NULL;
@@ -263,6 +265,8 @@ static int lm363x_regulator_probe(struct platform_device *pdev)
 					 LM3632_EXT_EN_MASK,
 					 LM3632_EXT_EN_MASK);
 		if (ret) {
+			if (gpiod)
+				gpiod_put(gpiod);
 			dev_err(dev, "External pin err: %d\n", ret);
 			return ret;
 		}

drivers/regulator/lochnagar-regulator.c

@@ -13,6 +13,7 @@
 #include <linux/module.h>
 #include <linux/mutex.h>
 #include <linux/of.h>
+#include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/regmap.h>
 #include <linux/regulator/driver.h>
@@ -20,6 +21,8 @@
 #include <linux/regulator/of_regulator.h>
 
 #include <linux/mfd/lochnagar.h>
+#include <linux/mfd/lochnagar1_regs.h>
+#include <linux/mfd/lochnagar2_regs.h>
 
 static const struct regulator_ops lochnagar_micvdd_ops = {
 	.enable = regulator_enable_regmap,
@@ -212,28 +215,52 @@ static const struct regulator_desc lochnagar_regulators[] = {
 	},
 };
 
+static const struct of_device_id lochnagar_of_match[] = {
+	{
+		.compatible = "cirrus,lochnagar2-micvdd",
+		.data = &lochnagar_regulators[LOCHNAGAR_MICVDD],
+	},
+	{
+		.compatible = "cirrus,lochnagar2-mic1vdd",
+		.data = &lochnagar_regulators[LOCHNAGAR_MIC1VDD],
+	},
+	{
+		.compatible = "cirrus,lochnagar2-mic2vdd",
+		.data = &lochnagar_regulators[LOCHNAGAR_MIC1VDD],
+	},
+	{
+		.compatible = "cirrus,lochnagar2-vddcore",
+		.data = &lochnagar_regulators[LOCHNAGAR_VDDCORE],
+	},
+	{},
+};
+
 static int lochnagar_regulator_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct lochnagar *lochnagar = dev_get_drvdata(dev->parent);
 	struct regulator_config config = { };
+	const struct of_device_id *of_id;
+	const struct regulator_desc *desc;
 	struct regulator_dev *rdev;
-	int ret, i;
+	int ret;
 
-	config.dev = lochnagar->dev;
+	config.dev = dev;
 	config.regmap = lochnagar->regmap;
 	config.driver_data = lochnagar;
 
-	for (i = 0; i < ARRAY_SIZE(lochnagar_regulators); i++) {
-		const struct regulator_desc *desc = &lochnagar_regulators[i];
+	of_id = of_match_device(lochnagar_of_match, dev);
+	if (!of_id)
+		return -EINVAL;
 
-		rdev = devm_regulator_register(dev, desc, &config);
-		if (IS_ERR(rdev)) {
-			ret = PTR_ERR(rdev);
-			dev_err(dev, "Failed to register %s regulator: %d\n",
-				desc->name, ret);
-			return ret;
-		}
+	desc = of_id->data;
+
+	rdev = devm_regulator_register(dev, desc, &config);
+	if (IS_ERR(rdev)) {
+		ret = PTR_ERR(rdev);
+		dev_err(dev, "Failed to register %s regulator: %d\n",
+			desc->name, ret);
+		return ret;
 	}
 
 	return 0;
@@ -242,6 +269,7 @@ static int lochnagar_regulator_probe(struct platform_device *pdev)
 static struct platform_driver lochnagar_regulator_driver = {
 	.driver = {
 		.name = "lochnagar-regulator",
+		.of_match_table = of_match_ptr(lochnagar_of_match),
 	},
 
 	.probe = lochnagar_regulator_probe,

drivers/regulator/lp8788-ldo.c

@@ -501,8 +501,12 @@ static int lp8788_config_ldo_enable_mode(struct platform_device *pdev,
 		return 0;
 	}
 
-	/* FIXME: check default mode for GPIO here: high or low? */
-	ldo->ena_gpiod = devm_gpiod_get_index_optional(&pdev->dev,
+	/*
+	 * Do not use devm* here: the regulator core takes over the
+	 * lifecycle management of the GPIO descriptor.
+	 * FIXME: check default mode for GPIO here: high or low?
+	 */
+	ldo->ena_gpiod = gpiod_get_index_optional(&pdev->dev,
 					       "enable",
 					       enable_id,
 					       GPIOD_OUT_HIGH |

drivers/regulator/max77686-regulator.c

@@ -11,8 +11,7 @@
 #include <linux/kernel.h>
 #include <linux/bug.h>
 #include <linux/err.h>
-#include <linux/gpio.h>
-#include <linux/of_gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/slab.h>
 #include <linux/platform_device.h>
 #include <linux/regulator/driver.h>
@@ -76,6 +75,7 @@ enum max77686_ramp_rate {
 };
 
 struct max77686_data {
+	struct device *dev;
 	DECLARE_BITMAP(gpio_enabled, MAX77686_REGULATORS);
 
 	/* Array indexed by regulator id */
@@ -250,26 +250,34 @@ static int max77686_of_parse_cb(struct device_node *np,
 		struct regulator_config *config)
 {
 	struct max77686_data *max77686 = config->driver_data;
+	int ret;
 
 	switch (desc->id) {
 	case MAX77686_BUCK8:
 	case MAX77686_BUCK9:
 	case MAX77686_LDO20 ... MAX77686_LDO22:
-		config->ena_gpio = of_get_named_gpio(np,
-					"maxim,ena-gpios", 0);
-		config->ena_gpio_flags = GPIOF_OUT_INIT_HIGH;
-		config->ena_gpio_initialized = true;
+		config->ena_gpiod = gpiod_get_from_of_node(np,
+				"maxim,ena",
+				0,
+				GPIOD_OUT_HIGH | GPIOD_FLAGS_BIT_NONEXCLUSIVE,
+				"max77686-regulator");
+		if (IS_ERR(config->ena_gpiod))
+			config->ena_gpiod = NULL;
 		break;
 	default:
 		return 0;
 	}
 
-	if (gpio_is_valid(config->ena_gpio)) {
+	if (config->ena_gpiod) {
 		set_bit(desc->id, max77686->gpio_enabled);
 
-		return regmap_update_bits(config->regmap, desc->enable_reg,
-					  desc->enable_mask,
-					  MAX77686_GPIO_CONTROL);
+		ret = regmap_update_bits(config->regmap, desc->enable_reg,
+					 desc->enable_mask,
+					 MAX77686_GPIO_CONTROL);
+		if (ret) {
+			gpiod_put(config->ena_gpiod);
+			config->ena_gpiod = NULL;
+		}
 	}
 
 	return 0;
@@ -507,6 +515,7 @@ static int max77686_pmic_probe(struct platform_device *pdev)
 	if (!max77686)
 		return -ENOMEM;
 
+	max77686->dev = &pdev->dev;
 	config.dev = iodev->dev;
 	config.regmap = iodev->regmap;
 	config.driver_data = max77686;

drivers/regulator/max8952.c

@@ -231,9 +231,13 @@ static int max8952_pmic_probe(struct i2c_client *client,
 	else
 		gflags = GPIOD_OUT_LOW;
 	gflags |= GPIOD_FLAGS_BIT_NONEXCLUSIVE;
-	gpiod = devm_gpiod_get_optional(&client->dev,
-					"max8952,en",
-					gflags);
+	/*
+	 * Do not use devm* here: the regulator core takes over the
+	 * lifecycle management of the GPIO descriptor.
+	 */
+	gpiod = gpiod_get_optional(&client->dev,
+				   "max8952,en",
+				   gflags);
 	if (IS_ERR(gpiod))
 		return PTR_ERR(gpiod);
 	if (gpiod)

drivers/regulator/max8973-regulator.c

@@ -808,7 +808,13 @@ static int max8973_probe(struct i2c_client *client,
 	config.of_node = client->dev.of_node;
 	config.regmap = max->regmap;
 
-	/* Register the regulators */
+	/*
+	 * Register the regulators
+	 * Turn the GPIO descriptor over to the regulator core for
+	 * lifecycle management if we pass an ena_gpiod.
+	 */
+	if (config.ena_gpiod)
+		devm_gpiod_unhinge(&client->dev, config.ena_gpiod);
 	rdev = devm_regulator_register(&client->dev, &max->desc, &config);
 	if (IS_ERR(rdev)) {
 		ret = PTR_ERR(rdev);

drivers/regulator/max8997-regulator.c

@@ -925,7 +925,7 @@ static int max8997_pmic_dt_parse_pdata(struct platform_device *pdev,
 	pdata->regulators = rdata;
 	for_each_child_of_node(regulators_np, reg_np) {
 		for (i = 0; i < ARRAY_SIZE(regulators); i++)
-			if (!of_node_cmp(reg_np->name, regulators[i].name))
+			if (of_node_name_eq(reg_np, regulators[i].name))
 				break;
 
 		if (i == ARRAY_SIZE(regulators)) {

drivers/regulator/mc13xxx-regulator-core.c

@@ -186,7 +186,7 @@ struct mc13xxx_regulator_init_data *mc13xxx_parse_regulators_dt(
 		for (i = 0; i < num_regulators; i++) {
 			if (!regulators[i].desc.name)
 				continue;
-			if (!of_node_cmp(child->name,
+			if (of_node_name_eq(child,
 					 regulators[i].desc.name)) {
 				p->id = i;
 				p->init_data = of_get_regulator_init_data(

drivers/regulator/mcp16502.c

+// SPDX-License-Identifier: GPL-2.0
+//
+// MCP16502 PMIC driver
+//
+// Copyright (C) 2018 Microchip Technology Inc. and its subsidiaries
+//
+// Author: Andrei Stefanescu <andrei.stefanescu@microchip.com>
+//
+// Inspired from tps65086-regulator.c
+
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/suspend.h>
+
+#define VDD_LOW_SEL 0x0D
+#define VDD_HIGH_SEL 0x3F
+
+#define MCP16502_FLT BIT(7)
+#define MCP16502_ENS BIT(0)
+
+/*
+ * The PMIC has four sets of registers corresponding to four power modes:
+ * Performance, Active, Low-power, Hibernate.
+ *
+ * Registers:
+ * Each regulator has a register for each power mode. To access a register
+ * for a specific regulator and mode BASE_* and OFFSET_* need to be added.
+ *
+ * Operating modes:
+ * In order for the PMIC to transition to operating modes it has to be
+ * controlled via GPIO lines called LPM and HPM.
+ *
+ * The registers are fully configurable such that you can put all regulators in
+ * a low-power state while the PMIC is in Active mode. They are supposed to be
+ * configured at startup and then simply transition to/from a global low-power
+ * state by setting the GPIO lpm pin high/low.
+ *
+ * This driver keeps the PMIC in Active mode, Low-power state is set for the
+ * regulators by enabling/disabling operating mode (FPWM or Auto PFM).
+ *
+ * The PMIC's Low-power and Hibernate modes are used during standby/suspend.
+ * To enter standby/suspend the PMIC will go to Low-power mode. From there, it
+ * will transition to Hibernate when the PWRHLD line is set to low by the MPU.
+ */
+
+/*
+ * This function is useful for iterating over all regulators and accessing their
+ * registers in a generic way or accessing a regulator device by its id.
+ */
+#define MCP16502_BASE(i) (((i) + 1) << 4)
+#define MCP16502_STAT_BASE(i) ((i) + 5)
+
+#define MCP16502_OFFSET_MODE_A 0
+#define MCP16502_OFFSET_MODE_LPM 1
+#define MCP16502_OFFSET_MODE_HIB 2
+
+#define MCP16502_OPMODE_ACTIVE REGULATOR_MODE_NORMAL
+#define MCP16502_OPMODE_LPM REGULATOR_MODE_IDLE
+#define MCP16502_OPMODE_HIB REGULATOR_MODE_STANDBY
+
+#define MCP16502_MODE_AUTO_PFM 0
+#define MCP16502_MODE_FPWM BIT(6)
+
+#define MCP16502_VSEL 0x3F
+#define MCP16502_EN BIT(7)
+#define MCP16502_MODE BIT(6)
+
+#define MCP16502_MIN_REG 0x0
+#define MCP16502_MAX_REG 0x65
+
+static unsigned int mcp16502_of_map_mode(unsigned int mode)
+{
+	if (mode == REGULATOR_MODE_NORMAL || mode == REGULATOR_MODE_IDLE)
+		return mode;
+
+	return REGULATOR_MODE_INVALID;
+}
+
+#define MCP16502_REGULATOR(_name, _id, _ranges, _ops)			\
+	[_id] = {							\
+		.name			= _name,			\
+		.regulators_node	= of_match_ptr("regulators"),	\
+		.id			= _id,				\
+		.ops			= &(_ops),			\
+		.type			= REGULATOR_VOLTAGE,		\
+		.owner			= THIS_MODULE,			\
+		.n_voltages		= MCP16502_VSEL + 1,		\
+		.linear_ranges		= _ranges,			\
+		.n_linear_ranges	= ARRAY_SIZE(_ranges),		\
+		.of_match		= of_match_ptr(_name),		\
+		.of_map_mode		= mcp16502_of_map_mode,		\
+		.vsel_reg		= (((_id) + 1) << 4),		\
+		.vsel_mask		= MCP16502_VSEL,		\
+		.enable_reg		= (((_id) + 1) << 4),		\
+		.enable_mask		= MCP16502_EN,			\
+	}
+
+enum {
+	BUCK1 = 0,
+	BUCK2,
+	BUCK3,
+	BUCK4,
+	LDO1,
+	LDO2,
+	NUM_REGULATORS
+};
+
+/*
+ * struct mcp16502 - PMIC representation
+ * @rdev: the regulators belonging to this chip
+ * @rmap: regmap to be used for I2C communication
+ * @lpm: LPM GPIO descriptor
+ */
+struct mcp16502 {
+	struct regulator_dev *rdev[NUM_REGULATORS];
+	struct regmap *rmap;
+	struct gpio_desc *lpm;
+};
+
+/*
+ * mcp16502_gpio_set_mode() - set the GPIO corresponding value
+ *
+ * Used to prepare transitioning into hibernate or resuming from it.
+ */
+static void mcp16502_gpio_set_mode(struct mcp16502 *mcp, int mode)
+{
+	switch (mode) {
+	case MCP16502_OPMODE_ACTIVE:
+		gpiod_set_value(mcp->lpm, 0);
+		break;
+	case MCP16502_OPMODE_LPM:
+	case MCP16502_OPMODE_HIB:
+		gpiod_set_value(mcp->lpm, 1);
+		break;
+	default:
+		pr_err("%s: %d invalid\n", __func__, mode);
+	}
+}
+
+/*
+ * mcp16502_get_reg() - get the PMIC's configuration register for opmode
+ *
+ * @rdev: the regulator whose register we are searching
+ * @opmode: the PMIC's operating mode ACTIVE, Low-power, Hibernate
+ */
+static int mcp16502_get_reg(struct regulator_dev *rdev, int opmode)
+{
+	int reg = MCP16502_BASE(rdev_get_id(rdev));
+
+	switch (opmode) {
+	case MCP16502_OPMODE_ACTIVE:
+		return reg + MCP16502_OFFSET_MODE_A;
+	case MCP16502_OPMODE_LPM:
+		return reg + MCP16502_OFFSET_MODE_LPM;
+	case MCP16502_OPMODE_HIB:
+		return reg + MCP16502_OFFSET_MODE_HIB;
+	default:
+		return -EINVAL;
+	}
+}
+
+/*
+ * mcp16502_get_mode() - return the current operating mode of a regulator
+ *
+ * Note: all functions that are not part of entering/exiting standby/suspend
+ *	 use the Active mode registers.
+ *
+ * Note: this is different from the PMIC's operatig mode, it is the
+ *	 MODE bit from the regulator's register.
+ */
+static unsigned int mcp16502_get_mode(struct regulator_dev *rdev)
+{
+	unsigned int val;
+	int ret, reg;
+	struct mcp16502 *mcp = rdev_get_drvdata(rdev);
+
+	reg = mcp16502_get_reg(rdev, MCP16502_OPMODE_ACTIVE);
+	if (reg < 0)
+		return reg;
+
+	ret = regmap_read(mcp->rmap, reg, &val);
+	if (ret)
+		return ret;
+
+	switch (val & MCP16502_MODE) {
+	case MCP16502_MODE_FPWM:
+		return REGULATOR_MODE_NORMAL;
+	case MCP16502_MODE_AUTO_PFM:
+		return REGULATOR_MODE_IDLE;
+	default:
+		return REGULATOR_MODE_INVALID;
+	}
+}
+
+/*
+ * _mcp16502_set_mode() - helper for set_mode and set_suspend_mode
+ *
+ * @rdev: the regulator for which we are setting the mode
+ * @mode: the regulator's mode (the one from MODE bit)
+ * @opmode: the PMIC's operating mode: Active/Low-power/Hibernate
+ */
+static int _mcp16502_set_mode(struct regulator_dev *rdev, unsigned int mode,
+			      unsigned int op_mode)
+{
+	int val;
+	int reg;
+	struct mcp16502 *mcp = rdev_get_drvdata(rdev);
+
+	reg = mcp16502_get_reg(rdev, op_mode);
+	if (reg < 0)
+		return reg;
+
+	switch (mode) {
+	case REGULATOR_MODE_NORMAL:
+		val = MCP16502_MODE_FPWM;
+		break;
+	case REGULATOR_MODE_IDLE:
+		val = MCP16502_MODE_AUTO_PFM;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	reg = regmap_update_bits(mcp->rmap, reg, MCP16502_MODE, val);
+	return reg;
+}
+
+/*
+ * mcp16502_set_mode() - regulator_ops set_mode
+ */
+static int mcp16502_set_mode(struct regulator_dev *rdev, unsigned int mode)
+{
+	return _mcp16502_set_mode(rdev, mode, MCP16502_OPMODE_ACTIVE);
+}
+
+/*
+ * mcp16502_get_status() - regulator_ops get_status
+ */
+static int mcp16502_get_status(struct regulator_dev *rdev)
+{
+	int ret;
+	unsigned int val;
+	struct mcp16502 *mcp = rdev_get_drvdata(rdev);
+
+	ret = regmap_read(mcp->rmap, MCP16502_STAT_BASE(rdev_get_id(rdev)),
+			  &val);
+	if (ret)
+		return ret;
+
+	if (val & MCP16502_FLT)
+		return REGULATOR_STATUS_ERROR;
+	else if (val & MCP16502_ENS)
+		return REGULATOR_STATUS_ON;
+	else if (!(val & MCP16502_ENS))
+		return REGULATOR_STATUS_OFF;
+
+	return REGULATOR_STATUS_UNDEFINED;
+}
+
+#ifdef CONFIG_SUSPEND
+/*
+ * mcp16502_suspend_get_target_reg() - get the reg of the target suspend PMIC
+ *				       mode
+ */
+static int mcp16502_suspend_get_target_reg(struct regulator_dev *rdev)
+{
+	switch (pm_suspend_target_state) {
+	case PM_SUSPEND_STANDBY:
+		return mcp16502_get_reg(rdev, MCP16502_OPMODE_LPM);
+	case PM_SUSPEND_ON:
+	case PM_SUSPEND_MEM:
+		return mcp16502_get_reg(rdev, MCP16502_OPMODE_HIB);
+	default:
+		dev_err(&rdev->dev, "invalid suspend target: %d\n",
+			pm_suspend_target_state);
+	}
+
+	return -EINVAL;
+}
+
+/*
+ * mcp16502_set_suspend_voltage() - regulator_ops set_suspend_voltage
+ */
+static int mcp16502_set_suspend_voltage(struct regulator_dev *rdev, int uV)
+{
+	struct mcp16502 *mcp = rdev_get_drvdata(rdev);
+	int sel = regulator_map_voltage_linear_range(rdev, uV, uV);
+	int reg = mcp16502_suspend_get_target_reg(rdev);
+
+	if (sel < 0)
+		return sel;
+
+	if (reg < 0)
+		return reg;
+
+	return regmap_update_bits(mcp->rmap, reg, MCP16502_VSEL, sel);
+}
+
+/*
+ * mcp16502_set_suspend_mode() - regulator_ops set_suspend_mode
+ */
+static int mcp16502_set_suspend_mode(struct regulator_dev *rdev,
+				     unsigned int mode)
+{
+	switch (pm_suspend_target_state) {
+	case PM_SUSPEND_STANDBY:
+		return _mcp16502_set_mode(rdev, mode, MCP16502_OPMODE_LPM);
+	case PM_SUSPEND_ON:
+	case PM_SUSPEND_MEM:
+		return _mcp16502_set_mode(rdev, mode, MCP16502_OPMODE_HIB);
+	default:
+		dev_err(&rdev->dev, "invalid suspend target: %d\n",
+			pm_suspend_target_state);
+	}
+
+	return -EINVAL;
+}
+
+/*
+ * mcp16502_set_suspend_enable() - regulator_ops set_suspend_enable
+ */
+static int mcp16502_set_suspend_enable(struct regulator_dev *rdev)
+{
+	struct mcp16502 *mcp = rdev_get_drvdata(rdev);
+	int reg = mcp16502_suspend_get_target_reg(rdev);
+
+	if (reg < 0)
+		return reg;
+
+	return regmap_update_bits(mcp->rmap, reg, MCP16502_EN, MCP16502_EN);
+}
+
+/*
+ * mcp16502_set_suspend_disable() - regulator_ops set_suspend_disable
+ */
+static int mcp16502_set_suspend_disable(struct regulator_dev *rdev)
+{
+	struct mcp16502 *mcp = rdev_get_drvdata(rdev);
+	int reg = mcp16502_suspend_get_target_reg(rdev);
+
+	if (reg < 0)
+		return reg;
+
+	return regmap_update_bits(mcp->rmap, reg, MCP16502_EN, 0);
+}
+#endif /* CONFIG_SUSPEND */
+
+static const struct regulator_ops mcp16502_buck_ops = {
+	.list_voltage			= regulator_list_voltage_linear_range,
+	.map_voltage			= regulator_map_voltage_linear_range,
+	.get_voltage_sel		= regulator_get_voltage_sel_regmap,
+	.set_voltage_sel		= regulator_set_voltage_sel_regmap,
+	.enable				= regulator_enable_regmap,
+	.disable			= regulator_disable_regmap,
+	.is_enabled			= regulator_is_enabled_regmap,
+	.get_status			= mcp16502_get_status,
+
+	.set_mode			= mcp16502_set_mode,
+	.get_mode			= mcp16502_get_mode,
+
+#ifdef CONFIG_SUSPEND
+	.set_suspend_voltage		= mcp16502_set_suspend_voltage,
+	.set_suspend_mode		= mcp16502_set_suspend_mode,
+	.set_suspend_enable		= mcp16502_set_suspend_enable,
+	.set_suspend_disable		= mcp16502_set_suspend_disable,
+#endif /* CONFIG_SUSPEND */
+};
+
+/*
+ * LDOs cannot change operating modes.
+ */
+static const struct regulator_ops mcp16502_ldo_ops = {
+	.list_voltage			= regulator_list_voltage_linear_range,
+	.map_voltage			= regulator_map_voltage_linear_range,
+	.get_voltage_sel		= regulator_get_voltage_sel_regmap,
+	.set_voltage_sel		= regulator_set_voltage_sel_regmap,
+	.enable				= regulator_enable_regmap,
+	.disable			= regulator_disable_regmap,
+	.is_enabled			= regulator_is_enabled_regmap,
+	.get_status			= mcp16502_get_status,
+
+#ifdef CONFIG_SUSPEND
+	.set_suspend_voltage		= mcp16502_set_suspend_voltage,
+	.set_suspend_enable		= mcp16502_set_suspend_enable,
+	.set_suspend_disable		= mcp16502_set_suspend_disable,
+#endif /* CONFIG_SUSPEND */
+};
+
+static const struct of_device_id mcp16502_ids[] = {
+	{ .compatible = "microchip,mcp16502", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, mcp16502_ids);
+
+static const struct regulator_linear_range b1l12_ranges[] = {
+	REGULATOR_LINEAR_RANGE(1200000, VDD_LOW_SEL, VDD_HIGH_SEL, 50000),
+};
+
+static const struct regulator_linear_range b234_ranges[] = {
+	REGULATOR_LINEAR_RANGE(600000, VDD_LOW_SEL, VDD_HIGH_SEL, 25000),
+};
+
+static const struct regulator_desc mcp16502_desc[] = {
+	/* MCP16502_REGULATOR(_name, _id, ranges, regulator_ops) */
+	MCP16502_REGULATOR("VDD_IO", BUCK1, b1l12_ranges, mcp16502_buck_ops),
+	MCP16502_REGULATOR("VDD_DDR", BUCK2, b234_ranges, mcp16502_buck_ops),
+	MCP16502_REGULATOR("VDD_CORE", BUCK3, b234_ranges, mcp16502_buck_ops),
+	MCP16502_REGULATOR("VDD_OTHER", BUCK4, b234_ranges, mcp16502_buck_ops),
+	MCP16502_REGULATOR("LDO1", LDO1, b1l12_ranges, mcp16502_ldo_ops),
+	MCP16502_REGULATOR("LDO2", LDO2, b1l12_ranges, mcp16502_ldo_ops)
+};
+
+static const struct regmap_range mcp16502_ranges[] = {
+	regmap_reg_range(MCP16502_MIN_REG, MCP16502_MAX_REG)
+};
+
+static const struct regmap_access_table mcp16502_yes_reg_table = {
+	.yes_ranges = mcp16502_ranges,
+	.n_yes_ranges = ARRAY_SIZE(mcp16502_ranges),
+};
+
+static const struct regmap_config mcp16502_regmap_config = {
+	.reg_bits	= 8,
+	.val_bits	= 8,
+	.max_register	= MCP16502_MAX_REG,
+	.cache_type	= REGCACHE_NONE,
+	.rd_table	= &mcp16502_yes_reg_table,
+	.wr_table	= &mcp16502_yes_reg_table,
+};
+
+/*
+ * set_up_regulators() - initialize all regulators
+ */
+static int setup_regulators(struct mcp16502 *mcp, struct device *dev,
+			    struct regulator_config config)
+{
+	int i;
+
+	for (i = 0; i < NUM_REGULATORS; i++) {
+		mcp->rdev[i] = devm_regulator_register(dev,
+						       &mcp16502_desc[i],
+						       &config);
+		if (IS_ERR(mcp->rdev[i])) {
+			dev_err(dev,
+				"failed to register %s regulator %ld\n",
+				mcp16502_desc[i].name, PTR_ERR(mcp->rdev[i]));
+			return PTR_ERR(mcp->rdev[i]);
+		}
+	}
+
+	return 0;
+}
+
+static int mcp16502_probe(struct i2c_client *client,
+			  const struct i2c_device_id *id)
+{
+	struct regulator_config config = { };
+	struct device *dev;
+	struct mcp16502 *mcp;
+	int ret = 0;
+
+	dev = &client->dev;
+	config.dev = dev;
+
+	mcp = devm_kzalloc(dev, sizeof(*mcp), GFP_KERNEL);
+	if (!mcp)
+		return -ENOMEM;
+
+	mcp->rmap = devm_regmap_init_i2c(client, &mcp16502_regmap_config);
+	if (IS_ERR(mcp->rmap)) {
+		ret = PTR_ERR(mcp->rmap);
+		dev_err(dev, "regmap init failed: %d\n", ret);
+		return ret;
+	}
+
+	i2c_set_clientdata(client, mcp);
+	config.regmap = mcp->rmap;
+	config.driver_data = mcp;
+
+	mcp->lpm = devm_gpiod_get(dev, "lpm", GPIOD_OUT_LOW);
+	if (IS_ERR(mcp->lpm)) {
+		dev_err(dev, "failed to get lpm pin: %ld\n", PTR_ERR(mcp->lpm));
+		return PTR_ERR(mcp->lpm);
+	}
+
+	ret = setup_regulators(mcp, dev, config);
+	if (ret != 0)
+		return ret;
+
+	mcp16502_gpio_set_mode(mcp, MCP16502_OPMODE_ACTIVE);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int mcp16502_suspend_noirq(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct mcp16502 *mcp = i2c_get_clientdata(client);
+
+	mcp16502_gpio_set_mode(mcp, MCP16502_OPMODE_LPM);
+
+	return 0;
+}
+
+static int mcp16502_resume_noirq(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct mcp16502 *mcp = i2c_get_clientdata(client);
+
+	mcp16502_gpio_set_mode(mcp, MCP16502_OPMODE_ACTIVE);
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_PM
+static const struct dev_pm_ops mcp16502_pm_ops = {
+	SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(mcp16502_suspend_noirq,
+				      mcp16502_resume_noirq)
+};
+#endif
+static const struct i2c_device_id mcp16502_i2c_id[] = {
+	{ "mcp16502", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, mcp16502_i2c_id);
+
+static struct i2c_driver mcp16502_drv = {
+	.probe		= mcp16502_probe,
+	.driver		= {
+		.name	= "mcp16502-regulator",
+		.of_match_table	= of_match_ptr(mcp16502_ids),
+#ifdef CONFIG_PM
+		.pm = &mcp16502_pm_ops,
+#endif
+	},
+	.id_table	= mcp16502_i2c_id,
+};
+
+module_i2c_driver(mcp16502_drv);
+
+MODULE_VERSION("1.0");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("MCP16502 PMIC driver");
+MODULE_AUTHOR("Andrei Stefanescu andrei.stefanescu@microchip.com");

drivers/regulator/of_regulator.c

@@ -20,6 +20,7 @@
 #include "internal.h"
 
 static const char *const regulator_states[PM_SUSPEND_MAX + 1] = {
+	[PM_SUSPEND_STANDBY]	= "regulator-state-standby",
 	[PM_SUSPEND_MEM]	= "regulator-state-mem",
 	[PM_SUSPEND_MAX]	= "regulator-state-disk",
 };
@@ -170,6 +171,10 @@ static void of_get_regulation_constraints(struct device_node *np,
 				  &pval))
 		constraints->max_spread = pval;
 
+	if (!of_property_read_u32(np, "regulator-max-step-microvolt",
+				  &pval))
+		constraints->max_uV_step = pval;
+
 	constraints->over_current_protection = of_property_read_bool(np,
 					"regulator-over-current-protection");
 
@@ -181,9 +186,11 @@ static void of_get_regulation_constraints(struct device_node *np,
 		case PM_SUSPEND_MAX:
 			suspend_state = &constraints->state_disk;
 			break;
+		case PM_SUSPEND_STANDBY:
+			suspend_state = &constraints->state_standby;
+			break;
 		case PM_SUSPEND_ON:
 		case PM_SUSPEND_TO_IDLE:
-		case PM_SUSPEND_STANDBY:
 		default:
 			continue;
 		}
@@ -364,24 +371,25 @@ int of_regulator_match(struct device *dev, struct device_node *node,
 }
 EXPORT_SYMBOL_GPL(of_regulator_match);
 
-struct regulator_init_data *regulator_of_get_init_data(struct device *dev,
-					    const struct regulator_desc *desc,
-					    struct regulator_config *config,
-					    struct device_node **node)
+struct device_node *regulator_of_get_init_node(struct device *dev,
+					       const struct regulator_desc *desc)
 {
 	struct device_node *search, *child;
-	struct regulator_init_data *init_data = NULL;
 	const char *name;
 
 	if (!dev->of_node || !desc->of_match)
 		return NULL;
 
-	if (desc->regulators_node)
+	if (desc->regulators_node) {
 		search = of_get_child_by_name(dev->of_node,
 					      desc->regulators_node);
-	else
+	} else {
 		search = of_node_get(dev->of_node);
 
+		if (!strcmp(desc->of_match, search->name))
+			return search;
+	}
+
 	if (!search) {
 		dev_dbg(dev, "Failed to find regulator container node '%s'\n",
 			desc->regulators_node);
@@ -393,35 +401,48 @@ struct regulator_init_data *regulator_of_get_init_data(struct device *dev,
 		if (!name)
 			name = child->name;
 
-		if (strcmp(desc->of_match, name))
-			continue;
+		if (!strcmp(desc->of_match, name))
+			return of_node_get(child);
+	}
 
-		init_data = of_get_regulator_init_data(dev, child, desc);
-		if (!init_data) {
-			dev_err(dev,
-				"failed to parse DT for regulator %pOFn\n",
-				child);
-			break;
-		}
+	of_node_put(search);
 
-		if (desc->of_parse_cb) {
-			if (desc->of_parse_cb(child, desc, config)) {
-				dev_err(dev,
-					"driver callback failed to parse DT for regulator %pOFn\n",
-					child);
-				init_data = NULL;
-				break;
-			}
-		}
+	return NULL;
+}
+
+struct regulator_init_data *regulator_of_get_init_data(struct device *dev,
+					    const struct regulator_desc *desc,
+					    struct regulator_config *config,
+					    struct device_node **node)
+{
+	struct device_node *child;
+	struct regulator_init_data *init_data = NULL;
 
-		of_node_get(child);
-		*node = child;
-		break;
+	child = regulator_of_get_init_node(dev, desc);
+	if (!child)
+		return NULL;
+
+	init_data = of_get_regulator_init_data(dev, child, desc);
+	if (!init_data) {
+		dev_err(dev, "failed to parse DT for regulator %pOFn\n", child);
+		goto error;
 	}
 
-	of_node_put(search);
+	if (desc->of_parse_cb && desc->of_parse_cb(child, desc, config)) {
+		dev_err(dev,
+			"driver callback failed to parse DT for regulator %pOFn\n",
+			child);
+		goto error;
+	}
+
+	*node = child;
 
 	return init_data;
+
+error:
+	of_node_put(child);
+
+	return NULL;
 }
 
 static int of_node_match(struct device *dev, const void *data)

drivers/regulator/palmas-regulator.c

@@ -443,13 +443,16 @@ static int palmas_ldo_write(struct palmas *palmas, unsigned int reg,
 static int palmas_set_mode_smps(struct regulator_dev *dev, unsigned int mode)
 {
 	int id = rdev_get_id(dev);
+	int ret;
 	struct palmas_pmic *pmic = rdev_get_drvdata(dev);
 	struct palmas_pmic_driver_data *ddata = pmic->palmas->pmic_ddata;
 	struct palmas_regs_info *rinfo = &ddata->palmas_regs_info[id];
 	unsigned int reg;
 	bool rail_enable = true;
 
-	palmas_smps_read(pmic->palmas, rinfo->ctrl_addr, &reg);
+	ret = palmas_smps_read(pmic->palmas, rinfo->ctrl_addr, &reg);
+	if (ret)
+		return ret;
 
 	reg &= ~PALMAS_SMPS12_CTRL_MODE_ACTIVE_MASK;
 

drivers/regulator/pfuze100-regulator.c

@@ -370,6 +370,7 @@ static struct pfuze_regulator pfuze100_regulators[] = {
 	PFUZE100_VGEN_REG(PFUZE100, VGEN4, PFUZE100_VGEN4VOL, 1800000, 3300000, 100000),
 	PFUZE100_VGEN_REG(PFUZE100, VGEN5, PFUZE100_VGEN5VOL, 1800000, 3300000, 100000),
 	PFUZE100_VGEN_REG(PFUZE100, VGEN6, PFUZE100_VGEN6VOL, 1800000, 3300000, 100000),
+	PFUZE100_COIN_REG(PFUZE100, COIN, PFUZE100_COINVOL, 0x7, pfuze100_coin),
 };
 
 static struct pfuze_regulator pfuze200_regulators[] = {
@@ -436,6 +437,7 @@ static struct of_regulator_match pfuze100_matches[] = {
 	{ .name = "vgen4",	},
 	{ .name = "vgen5",	},
 	{ .name = "vgen6",	},
+	{ .name = "coin",	},
 };
 
 /* PFUZE200 */

drivers/regulator/qcom-rpmh-regulator.c

@@ -410,7 +410,7 @@ static int rpmh_regulator_init_vreg(struct rpmh_vreg *vreg, struct device *dev,
 	vreg->dev = dev;
 
 	for (rpmh_data = pmic_rpmh_data; rpmh_data->name; rpmh_data++)
-		if (!strcmp(rpmh_data->name, node->name))
+		if (of_node_name_eq(node, rpmh_data->name))
 			break;
 
 	if (!rpmh_data->name) {

drivers/regulator/s2mps11.c

@@ -5,7 +5,7 @@
 
 #include <linux/bug.h>
 #include <linux/err.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/slab.h>
 #include <linux/module.h>
 #include <linux/of.h>
@@ -14,7 +14,6 @@
 #include <linux/regulator/driver.h>
 #include <linux/regulator/machine.h>
 #include <linux/regulator/of_regulator.h>
-#include <linux/of_gpio.h>
 #include <linux/mfd/samsung/core.h>
 #include <linux/mfd/samsung/s2mps11.h>
 #include <linux/mfd/samsung/s2mps13.h>
@@ -44,7 +43,7 @@ struct s2mps11_info {
 	 * Array (size: number of regulators) with GPIO-s for external
 	 * sleep control.
 	 */
-	int *ext_control_gpio;
+	struct gpio_desc **ext_control_gpiod;
 };
 
 static int get_ramp_delay(int ramp_delay)
@@ -511,7 +510,7 @@ static int s2mps14_regulator_enable(struct regulator_dev *rdev)
 	case S2MPS14X:
 		if (test_bit(rdev_get_id(rdev), s2mps11->suspend_state))
 			val = S2MPS14_ENABLE_SUSPEND;
-		else if (gpio_is_valid(s2mps11->ext_control_gpio[rdev_get_id(rdev)]))
+		else if (s2mps11->ext_control_gpiod[rdev_get_id(rdev)])
 			val = S2MPS14_ENABLE_EXT_CONTROL;
 		else
 			val = rdev->desc->enable_mask;
@@ -805,7 +804,7 @@ static int s2mps14_pmic_enable_ext_control(struct s2mps11_info *s2mps11,
 static void s2mps14_pmic_dt_parse_ext_control_gpio(struct platform_device *pdev,
 		struct of_regulator_match *rdata, struct s2mps11_info *s2mps11)
 {
-	int *gpio = s2mps11->ext_control_gpio;
+	struct gpio_desc **gpio = s2mps11->ext_control_gpiod;
 	unsigned int i;
 	unsigned int valid_regulators[3] = { S2MPS14_LDO10, S2MPS14_LDO11,
 		S2MPS14_LDO12 };
@@ -816,11 +815,20 @@ static void s2mps14_pmic_dt_parse_ext_control_gpio(struct platform_device *pdev,
 		if (!rdata[reg].init_data || !rdata[reg].of_node)
 			continue;
 
-		gpio[reg] = of_get_named_gpio(rdata[reg].of_node,
-				"samsung,ext-control-gpios", 0);
-		if (gpio_is_valid(gpio[reg]))
-			dev_dbg(&pdev->dev, "Using GPIO %d for ext-control over %d/%s\n",
-					gpio[reg], reg, rdata[reg].name);
+		gpio[reg] = devm_gpiod_get_from_of_node(&pdev->dev,
+				rdata[reg].of_node,
+				"samsung,ext-control-gpios",
+				0,
+				GPIOD_OUT_HIGH | GPIOD_FLAGS_BIT_NONEXCLUSIVE,
+				"s2mps11-regulator");
+		if (IS_ERR(gpio[reg])) {
+			dev_err(&pdev->dev, "Failed to get control GPIO for %d/%s\n",
+				reg, rdata[reg].name);
+			continue;
+		}
+		if (gpio[reg])
+			dev_dbg(&pdev->dev, "Using GPIO for ext-control over %d/%s\n",
+				reg, rdata[reg].name);
 	}
 }
 
@@ -1126,17 +1134,10 @@ static int s2mps11_pmic_probe(struct platform_device *pdev)
 		return -EINVAL;
 	}
 
-	s2mps11->ext_control_gpio = devm_kmalloc_array(&pdev->dev,
-			rdev_num, sizeof(*s2mps11->ext_control_gpio),
-			GFP_KERNEL);
-	if (!s2mps11->ext_control_gpio)
+	s2mps11->ext_control_gpiod = devm_kcalloc(&pdev->dev, rdev_num,
+			       sizeof(*s2mps11->ext_control_gpiod), GFP_KERNEL);
+	if (!s2mps11->ext_control_gpiod)
 		return -ENOMEM;
-	/*
-	 * 0 is a valid GPIO so initialize all GPIO-s to negative value
-	 * to indicate that external control won't be used for this regulator.
-	 */
-	for (i = 0; i < rdev_num; i++)
-		s2mps11->ext_control_gpio[i] = -EINVAL;
 
 	if (!iodev->dev->of_node) {
 		if (iodev->pdata) {
@@ -1166,8 +1167,6 @@ static int s2mps11_pmic_probe(struct platform_device *pdev)
 	config.dev = &pdev->dev;
 	config.regmap = iodev->regmap_pmic;
 	config.driver_data = s2mps11;
-	config.ena_gpio_flags = GPIOF_OUT_INIT_HIGH;
-	config.ena_gpio_initialized = true;
 	for (i = 0; i < rdev_num; i++) {
 		struct regulator_dev *regulator;
 
@@ -1178,8 +1177,13 @@ static int s2mps11_pmic_probe(struct platform_device *pdev)
 			config.init_data = rdata[i].init_data;
 			config.of_node = rdata[i].of_node;
 		}
-		config.ena_gpio = s2mps11->ext_control_gpio[i];
-
+		config.ena_gpiod = s2mps11->ext_control_gpiod[i];
+		/*
+		 * Hand the GPIO descriptor management over to the regulator
+		 * core, remove it from devres management.
+		 */
+		if (config.ena_gpiod)
+			devm_gpiod_unhinge(&pdev->dev, config.ena_gpiod);
 		regulator = devm_regulator_register(&pdev->dev,
 						&regulators[i], &config);
 		if (IS_ERR(regulator)) {
@@ -1189,7 +1193,7 @@ static int s2mps11_pmic_probe(struct platform_device *pdev)
 			goto out;
 		}
 
-		if (gpio_is_valid(s2mps11->ext_control_gpio[i])) {
+		if (s2mps11->ext_control_gpiod[i]) {
 			ret = s2mps14_pmic_enable_ext_control(s2mps11,
 					regulator);
 			if (ret < 0) {

drivers/regulator/s5m8767.c

@@ -561,7 +561,7 @@ static int s5m8767_pmic_dt_parse_pdata(struct platform_device *pdev,
 	pdata->opmode = rmode;
 	for_each_child_of_node(regulators_np, reg_np) {
 		for (i = 0; i < ARRAY_SIZE(regulators); i++)
-			if (!of_node_cmp(reg_np->name, regulators[i].name))
+			if (of_node_name_eq(reg_np, regulators[i].name))
 				break;
 
 		if (i == ARRAY_SIZE(regulators)) {
@@ -956,10 +956,17 @@ static int s5m8767_pmic_probe(struct platform_device *pdev)
 		config.regmap = iodev->regmap_pmic;
 		config.of_node = pdata->regulators[i].reg_node;
 		config.ena_gpiod = NULL;
-		if (pdata->regulators[i].ext_control_gpiod)
+		if (pdata->regulators[i].ext_control_gpiod) {
+			/* Assigns config.ena_gpiod */
 			s5m8767_regulator_config_ext_control(s5m8767,
 					&pdata->regulators[i], &config);
 
+			/*
+			 * Hand the GPIO descriptor management over to the
+			 * regulator core, remove it from devres management.
+			 */
+			devm_gpiod_unhinge(s5m8767->dev, config.ena_gpiod);
+		}
 		rdev = devm_regulator_register(&pdev->dev, &regulators[id],
 						  &config);
 		if (IS_ERR(rdev)) {

drivers/regulator/stpmic1_regulator.c

@@ -489,14 +489,14 @@ static irqreturn_t stpmic1_curlim_irq_handler(int irq, void *data)
 {
 	struct regulator_dev *rdev = (struct regulator_dev *)data;
 
-	mutex_lock(&rdev->mutex);
+	regulator_lock(rdev);
 
 	/* Send an overcurrent notification */
 	regulator_notifier_call_chain(rdev,
 				      REGULATOR_EVENT_OVER_CURRENT,
 				      NULL);
 
-	mutex_unlock(&rdev->mutex);
+	regulator_unlock(rdev);
 
 	return IRQ_HANDLED;
 }

drivers/regulator/tps65090-regulator.c

@@ -480,6 +480,12 @@ static int tps65090_regulator_probe(struct platform_device *pdev)
 		else
 			config.of_node = NULL;
 
+		/*
+		 * Hand the GPIO descriptor management over to the regulator
+		 * core, remove it from devres management.
+		 */
+		if (config.ena_gpiod)
+			devm_gpiod_unhinge(&pdev->dev, config.ena_gpiod);
 		rdev = devm_regulator_register(&pdev->dev, ri->desc, &config);
 		if (IS_ERR(rdev)) {
 			dev_err(&pdev->dev, "failed to register regulator %s\n",

drivers/regulator/tps65910-regulator.c

@@ -1102,8 +1102,10 @@ static int tps65910_probe(struct platform_device *pdev)
 	platform_set_drvdata(pdev, pmic);
 
 	/* Give control of all register to control port */
-	tps65910_reg_set_bits(pmic->mfd, TPS65910_DEVCTRL,
+	err = tps65910_reg_set_bits(pmic->mfd, TPS65910_DEVCTRL,
 				DEVCTRL_SR_CTL_I2C_SEL_MASK);
+	if (err < 0)
+		return err;
 
 	switch (tps65910_chip_id(tps65910)) {
 	case TPS65910:

drivers/regulator/wm8350-regulator.c

@@ -1153,7 +1153,7 @@ static irqreturn_t pmic_uv_handler(int irq, void *data)
 {
 	struct regulator_dev *rdev = (struct regulator_dev *)data;
 
-	mutex_lock(&rdev->mutex);
+	regulator_lock(rdev);
 	if (irq == WM8350_IRQ_CS1 || irq == WM8350_IRQ_CS2)
 		regulator_notifier_call_chain(rdev,
 					      REGULATOR_EVENT_REGULATION_OUT,
@@ -1162,7 +1162,7 @@ static irqreturn_t pmic_uv_handler(int irq, void *data)
 		regulator_notifier_call_chain(rdev,
 					      REGULATOR_EVENT_UNDER_VOLTAGE,
 					      NULL);
-	mutex_unlock(&rdev->mutex);
+	regulator_unlock(rdev);
 
 	return IRQ_HANDLED;
 }

drivers/regulator/wm8994-regulator.c

@@ -19,7 +19,7 @@
 #include <linux/platform_device.h>
 #include <linux/regulator/driver.h>
 #include <linux/regulator/machine.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/slab.h>
 
 #include <linux/mfd/wm8994/core.h>
@@ -129,6 +129,7 @@ static int wm8994_ldo_probe(struct platform_device *pdev)
 	int id = pdev->id % ARRAY_SIZE(pdata->ldo);
 	struct regulator_config config = { };
 	struct wm8994_ldo *ldo;
+	struct gpio_desc *gpiod;
 	int ret;
 
 	dev_dbg(&pdev->dev, "Probing LDO%d\n", id + 1);
@@ -145,12 +146,18 @@ static int wm8994_ldo_probe(struct platform_device *pdev)
 	config.driver_data = ldo;
 	config.regmap = wm8994->regmap;
 	config.init_data = &ldo->init_data;
-	if (pdata) {
-		config.ena_gpio = pdata->ldo[id].enable;
-	} else if (wm8994->dev->of_node) {
-		config.ena_gpio = wm8994->pdata.ldo[id].enable;
-		config.ena_gpio_initialized = true;
-	}
+
+	/*
+	 * Look up LDO enable GPIO from the parent device node, we don't
+	 * use devm because the regulator core will free the GPIO
+	 */
+	gpiod = gpiod_get_optional(pdev->dev.parent,
+				   id ? "wlf,ldo2ena" : "wlf,ldo1ena",
+				   GPIOD_OUT_LOW |
+				   GPIOD_FLAGS_BIT_NONEXCLUSIVE);
+	if (IS_ERR(gpiod))
+		return PTR_ERR(gpiod);
+	config.ena_gpiod = gpiod;
 
 	/* Use default constraints if none set up */
 	if (!pdata || !pdata->ldo[id].init_data || wm8994->dev->of_node) {
@@ -159,12 +166,17 @@ static int wm8994_ldo_probe(struct platform_device *pdev)
 
 		ldo->init_data = wm8994_ldo_default[id];
 		ldo->init_data.consumer_supplies = &ldo->supply;
-		if (!config.ena_gpio)
+		if (!gpiod)
 			ldo->init_data.constraints.valid_ops_mask = 0;
 	} else {
 		ldo->init_data = *pdata->ldo[id].init_data;
 	}
 
+	/*
+	 * At this point the GPIO descriptor is handled over to the
+	 * regulator core and we need not worry about it on the
+	 * error path.
+	 */
 	ldo->regulator = devm_regulator_register(&pdev->dev,
 						 &wm8994_ldo_desc[id],
 						 &config);
@@ -172,15 +184,12 @@ static int wm8994_ldo_probe(struct platform_device *pdev)
 		ret = PTR_ERR(ldo->regulator);
 		dev_err(wm8994->dev, "Failed to register LDO%d: %d\n",
 			id + 1, ret);
-		goto err;
+		return ret;
 	}
 
 	platform_set_drvdata(pdev, ldo);
 
 	return 0;
-
-err:
-	return ret;
 }
 
 static struct platform_driver wm8994_ldo_driver = {

drivers/spi/spi-qcom-qspi.c

@@ -90,6 +90,9 @@
 #define PIO_DATAOUT_1B		0x0020
 #define PIO_DATAOUT_4B		0x0024
 
+#define RD_FIFO_CFG		0x0028
+#define CONTINUOUS_MODE		BIT(0)
+
 #define RD_FIFO_STATUS	0x002c
 #define FIFO_EMPTY	BIT(11)
 #define WR_CNTS_MSK	0x7f0
@@ -99,9 +102,6 @@
 #define RDY_16BYTE	BIT(1)
 #define FIFO_RDY	BIT(0)
 
-#define RD_FIFO_CFG		0x0028
-#define CONTINUOUS_MODE		BIT(0)
-
 #define RD_FIFO_RESET		0x0030
 #define RESET_FIFO		BIT(0)
 
@@ -139,7 +139,7 @@ struct qcom_qspi {
 	struct device *dev;
 	struct clk_bulk_data clks[QSPI_NUM_CLKS];
 	struct qspi_xfer xfer;
-	/* Lock to protect data accessed by IRQs */
+	/* Lock to protect xfer and IRQ accessed registers */
 	spinlock_t lock;
 };
 

include/dt-bindings/regulator/active-semi,8945a-regulator.h

+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2018 Microchip Technology, Inc. All rights reserved.
+ *
+ * Device Tree binding constants for the ACT8945A PMIC regulators
+ */
+
+#ifndef _DT_BINDINGS_REGULATOR_ACT8945A_H
+#define _DT_BINDINGS_REGULATOR_ACT8945A_H
+
+/*
+ * These constants should be used to specify regulator modes in device tree for
+ * ACT8945A regulators as follows:
+ * ACT8945A_REGULATOR_MODE_FIXED:	It is specific to DCDC regulators and it
+ *					specifies the usage of fixed-frequency
+ *					PWM.
+ *
+ * ACT8945A_REGULATOR_MODE_NORMAL:	It is specific to LDO regulators and it
+ *					specifies the usage of normal mode.
+ *
+ * ACT8945A_REGULATOR_MODE_LOWPOWER:	For DCDC and LDO regulators; it specify
+ *					the usage of proprietary power-saving
+ *					mode.
+ */
+
+#define ACT8945A_REGULATOR_MODE_FIXED		1
+#define ACT8945A_REGULATOR_MODE_NORMAL		2
+#define ACT8945A_REGULATOR_MODE_LOWPOWER	3
+
+#endif

include/linux/gpio/consumer.h

@@ -104,6 +104,7 @@ struct gpio_descs *__must_check
 devm_gpiod_get_array_optional(struct device *dev, const char *con_id,
 			      enum gpiod_flags flags);
 void devm_gpiod_put(struct device *dev, struct gpio_desc *desc);
+void devm_gpiod_unhinge(struct device *dev, struct gpio_desc *desc);
 void devm_gpiod_put_array(struct device *dev, struct gpio_descs *descs);
 
 int gpiod_get_direction(struct gpio_desc *desc);
@@ -172,6 +173,10 @@ int desc_to_gpio(const struct gpio_desc *desc);
 struct device_node;
 struct fwnode_handle;
 
+struct gpio_desc *gpiod_get_from_of_node(struct device_node *node,
+					 const char *propname, int index,
+					 enum gpiod_flags dflags,
+					 const char *label);
 struct gpio_desc *devm_gpiod_get_from_of_node(struct device *dev,
 					      struct device_node *node,
 					      const char *propname, int index,
@@ -245,6 +250,15 @@ static inline void gpiod_put(struct gpio_desc *desc)
 	WARN_ON(1);
 }
 
+static inline void devm_gpiod_unhinge(struct device *dev,
+				      struct gpio_desc *desc)
+{
+	might_sleep();
+
+	/* GPIO can never have been requested */
+	WARN_ON(1);
+}
+
 static inline void gpiod_put_array(struct gpio_descs *descs)
 {
 	might_sleep();
@@ -517,6 +531,15 @@ static inline int desc_to_gpio(const struct gpio_desc *desc)
 struct device_node;
 struct fwnode_handle;
 
+static inline
+struct gpio_desc *gpiod_get_from_of_node(struct device_node *node,
+					 const char *propname, int index,
+					 enum gpiod_flags dflags,
+					 const char *label)
+{
+	return ERR_PTR(-ENOSYS);
+}
+
 static inline
 struct gpio_desc *devm_gpiod_get_from_of_node(struct device *dev,
 					      struct device_node *node,

include/linux/mfd/axp20x.h

@@ -35,7 +35,7 @@ enum axp20x_variants {
 #define AXP152_ALDO_OP_MODE		0x13
 #define AXP152_LDO0_CTRL		0x15
 #define AXP152_DCDC2_V_OUT		0x23
-#define AXP152_DCDC2_V_SCAL		0x25
+#define AXP152_DCDC2_V_RAMP		0x25
 #define AXP152_DCDC1_V_OUT		0x26
 #define AXP152_DCDC3_V_OUT		0x27
 #define AXP152_ALDO12_V_OUT		0x28
@@ -53,7 +53,7 @@ enum axp20x_variants {
 #define AXP20X_USB_OTG_STATUS		0x02
 #define AXP20X_PWR_OUT_CTRL		0x12
 #define AXP20X_DCDC2_V_OUT		0x23
-#define AXP20X_DCDC2_LDO3_V_SCAL	0x25
+#define AXP20X_DCDC2_LDO3_V_RAMP	0x25
 #define AXP20X_DCDC3_V_OUT		0x27
 #define AXP20X_LDO24_V_OUT		0x28
 #define AXP20X_LDO3_V_OUT		0x29

include/linux/mfd/wm8994/pdata.h

@@ -20,9 +20,6 @@
 #define WM8994_NUM_AIF   3
 
 struct wm8994_ldo_pdata {
-	/** GPIOs to enable regulator, 0 or less if not available */
-	int enable;
-
 	const struct regulator_init_data *init_data;
 };
 

include/linux/regulator/consumer.h

@@ -508,7 +508,7 @@ static inline int regulator_get_error_flags(struct regulator *regulator,
 
 static inline int regulator_set_load(struct regulator *regulator, int load_uA)
 {
-	return REGULATOR_MODE_NORMAL;
+	return 0;
 }
 
 static inline int regulator_allow_bypass(struct regulator *regulator,

include/linux/regulator/driver.h

@@ -15,11 +15,12 @@
 #ifndef __LINUX_REGULATOR_DRIVER_H_
 #define __LINUX_REGULATOR_DRIVER_H_
 
-#define MAX_COUPLED		4
+#define MAX_COUPLED		2
 
 #include <linux/device.h>
 #include <linux/notifier.h>
 #include <linux/regulator/consumer.h>
+#include <linux/ww_mutex.h>
 
 struct gpio_desc;
 struct regmap;
@@ -462,7 +463,7 @@ struct regulator_dev {
 	struct coupling_desc coupling_desc;
 
 	struct blocking_notifier_head notifier;
-	struct mutex mutex; /* consumer lock */
+	struct ww_mutex mutex; /* consumer lock */
 	struct task_struct *mutex_owner;
 	int ref_cnt;
 	struct module *owner;
@@ -473,7 +474,6 @@ struct regulator_dev {
 	struct regmap *regmap;
 
 	struct delayed_work disable_work;
-	int deferred_disables;
 
 	void *reg_data;		/* regulator_dev data */
 
@@ -545,4 +545,7 @@ int regulator_set_active_discharge_regmap(struct regulator_dev *rdev,
 					  bool enable);
 void *regulator_get_init_drvdata(struct regulator_init_data *reg_init_data);
 
+void regulator_lock(struct regulator_dev *rdev);
+void regulator_unlock(struct regulator_dev *rdev);
+
 #endif

include/linux/regulator/machine.h

@@ -158,6 +158,9 @@ struct regulation_constraints {
 	/* used for coupled regulators */
 	int max_spread;
 
+	/* used for changing voltage in steps */
+	int max_uV_step;
+
 	/* valid regulator operating modes for this machine */
 	unsigned int valid_modes_mask;
 

include/linux/regulator/pfuze100.h

@@ -33,7 +33,8 @@
 #define PFUZE100_VGEN4		12
 #define PFUZE100_VGEN5		13
 #define PFUZE100_VGEN6		14
-#define PFUZE100_MAX_REGULATOR	15
+#define PFUZE100_COIN		15
+#define PFUZE100_MAX_REGULATOR	16
 
 #define PFUZE200_SW1AB		0
 #define PFUZE200_SW2		1