usb: xhci: add a quirk bit for ssic port unused

Two workarounds introduced by commit b8cb91e0 ("xhci: Workaround
for PME stuck issues in Intel xhci") and commit abce329c ("xhci:
Workaround to get D3 working in Intel xHCI") share a single quirk bit
XHCI_PME_STUCK_QUIRK. These two workarounds actually are different and
might happen on different hardwares. Need to separate them by adding a
quirk bit for the later.

Cc: stable@vger.kernel.org
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/usb/host/xhci-pci.c

@@ -156,6 +156,10 @@ static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci)
 		 pdev->device == PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI)) {
 		xhci->quirks |= XHCI_PME_STUCK_QUIRK;
 	}
+	if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
+		 pdev->device == PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI) {
+		xhci->quirks |= XHCI_SSIC_PORT_UNUSED;
+	}
 	if (pdev->vendor == PCI_VENDOR_ID_ETRON &&
 			pdev->device == PCI_DEVICE_ID_EJ168) {
 		xhci->quirks |= XHCI_RESET_ON_RESUME;
@@ -314,29 +318,20 @@ static void xhci_pci_remove(struct pci_dev *dev)
  * SSIC PORT need to be marked as "unused" before putting xHCI
  * into D3. After D3 exit, the SSIC port need to be marked as "used".
  * Without this change, xHCI might not enter D3 state.
- * Make sure PME works on some Intel xHCI controllers by writing 1 to clear
- * the Internal PME flag bit in vendor specific PMCTRL register at offset 0x80a4
  */
-static void xhci_pme_quirk(struct usb_hcd *hcd, bool suspend)
+static void xhci_ssic_port_unused_quirk(struct usb_hcd *hcd, bool suspend)
 {
 	struct xhci_hcd	*xhci = hcd_to_xhci(hcd);
-	struct pci_dev		*pdev = to_pci_dev(hcd->self.controller);
 	u32 val;
 	void __iomem *reg;
 	int i;
 
-	if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
-		 pdev->device == PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI) {
-
 	for (i = 0; i < SSIC_PORT_NUM; i++) {
 		reg = (void __iomem *) xhci->cap_regs +
 				SSIC_PORT_CFG2 +
 				i * SSIC_PORT_CFG2_OFFSET;
 
-			/*
-			 * Notify SSIC that SSIC profile programming
-			 * is not done.
-			 */
+		/* Notify SSIC that SSIC profile programming is not done. */
 		val = readl(reg) & ~PROG_DONE;
 		writel(val, reg);
 
@@ -353,7 +348,17 @@ static void xhci_pme_quirk(struct usb_hcd *hcd, bool suspend)
 		writel(val, reg);
 		readl(reg);
 	}
-	}
+}
+
+/*
+ * Make sure PME works on some Intel xHCI controllers by writing 1 to clear
+ * the Internal PME flag bit in vendor specific PMCTRL register at offset 0x80a4
+ */
+static void xhci_pme_quirk(struct usb_hcd *hcd)
+{
+	struct xhci_hcd	*xhci = hcd_to_xhci(hcd);
+	void __iomem *reg;
+	u32 val;
 
 	reg = (void __iomem *) xhci->cap_regs + 0x80a4;
 	val = readl(reg);
@@ -374,7 +379,10 @@ static int xhci_pci_suspend(struct usb_hcd *hcd, bool do_wakeup)
 		pdev->no_d3cold = true;
 
 	if (xhci->quirks & XHCI_PME_STUCK_QUIRK)
-		xhci_pme_quirk(hcd, true);
+		xhci_pme_quirk(hcd);
+
+	if (xhci->quirks & XHCI_SSIC_PORT_UNUSED)
+		xhci_ssic_port_unused_quirk(hcd, true);
 
 	return xhci_suspend(xhci, do_wakeup);
 }
@@ -406,8 +414,11 @@ static int xhci_pci_resume(struct usb_hcd *hcd, bool hibernated)
 	if (pdev->vendor == PCI_VENDOR_ID_INTEL)
 		usb_enable_intel_xhci_ports(pdev);
 
+	if (xhci->quirks & XHCI_SSIC_PORT_UNUSED)
+		xhci_ssic_port_unused_quirk(hcd, false);
+
 	if (xhci->quirks & XHCI_PME_STUCK_QUIRK)
-		xhci_pme_quirk(hcd, false);
+		xhci_pme_quirk(hcd);
 
 	retval = xhci_resume(xhci, hibernated);
 	return retval;

drivers/usb/host/xhci.h

@@ -1631,6 +1631,7 @@ struct xhci_hcd {
 #define XHCI_BROKEN_STREAMS	(1 << 19)
 #define XHCI_PME_STUCK_QUIRK	(1 << 20)
 #define XHCI_MTK_HOST		(1 << 21)
+#define XHCI_SSIC_PORT_UNUSED	(1 << 22)
 	unsigned int		num_active_eps;
 	unsigned int		limit_active_eps;
 	/* There are two roothubs to keep track of bus suspend info for */